section b index standard aluminum products …...standard aluminum products inc. wind loads 450...
TRANSCRIPT
STANDARD ALUMINUM PRODUCTS INC.
Section B IndexStorefront Framing Systems
450 s/g Flush Glazed System Specification B1
450 s/g Flush Glazed System Wind Load B2
450 s/g Flush Glazed System Profiles
550 d/g Flush Glazed System Specification
B3-B9
B10
550 d/g Flush Glazed System Wind Load B11
550 d/g Flush Glazed System Profiles B12-B18
550T d/g Thermally Broken Flush Glazed System Specification B20
550T d/g Thermally Broken Flush Glazed System Wind Load B21
550T d/g Thermally Broken Flush Glazed System Profiles B22-B28
Sash & Stop B32
Adjustable Base B32
U Channels B33
Miscellaneous Tubing B34
550T d/g Thermally Broken c/w 200T Door Profiles B29-B31
STANDARD ALUMINUM PRODUCTS INC.
Specification450 Series Flushed Glazed
B-1
Design
The system shall be 4 ½” x 1 ¾” center line
flush glazing and accommodate glass from
3mm to 10mm thick. The system can be
glazed from interior or exterior and is dry
glaze.
Performance
See Wind load Charts.
Structural performance shall conform to CSA
Standard CAN3-S157 “Strength design in
Aluminum” and a maximum deflection
of 1/175 of the span.
Material
Extrusions shall be 6063 alloy and T5 Temper.
Glazing gaskets shall be EPDM elastomeric
extrusions.
Finish
Both anodized and painted finishes are
available. All integral colour anodizing is
Architectural Class II., 0.4 to 0.7 mm coating.
A fluropolymer paint coating conforming to the
requirements of AAMA 603 and AAMA 605
specifications, the toughest coating in the
industry standards.
Testing
All testing shall be on full size frame sections.
Air infiltration shall be tested in accordance
with ASTM-Designation E283-91 or ASHRAE
standards #90-80
Fabrication
Framing should be fabricated from extrusions
of size and shape in accordance with shop
drawings. The framing system shall provide
for flush glazing while maintaining
the 1 ¾” nominal face dimensions.
The 450 Series has a complete number of
sections including deflection header and
extruded sub sill runner that can satisfy any
design requirements.
Construction
Frames shall have mechanically joined
corners with no exposed screws. All joints
shall be accurately fitted free of burrs and
rough edges. Complete frame assemblies
shall be free of warp. Each type of entrance
framing systems is compatible with all
Standard Aluminum swing doors and sliding
mall fronts.
Installation
Experienced technicians in accordance with
approved shop drawings shall install all
frames. The frames shall be set plumb,
square, and level and in correct alignment and
adjacent construction. All anchoring shall suit
the type of construction of the perimeter work.
Protection and Cleaning
After installation the general contractor should
adequately protect the exposed aluminum and
glass surfaces from damage by other trades.
i.e.(but not restricted to) cement splash and
leach, grinding, polishing compounds, plaster,
paint, lime, acids and other contaminants.
STANDARD ALUMINUM PRODUCTS INC.
Wind Loads450 Series Flushed Glazed
B-2SCALE 1/2 FULL SIZE
Calculations are based on CAN3-S157-M83 "Strength Design In Aluminum" using
6063-T5 Alloy-Temper, and a Deflection Limit = Span/175
2
5
6
7
8
9
10
11
12
13
14
15
3 4 5 6 7
Height (Feet)
Module Width, (Feet)
Part # - 450 & 451
2
7
8
9
10
11
12
13
14
15
16
18
3 4 5 6 8
Height (Feet)
Module Width, (Feet)
c/w 12 Gauge Reinforcing
7
17
25 PSF
15 PSF
30 PSF
35 PSF
20 PSF
25 PSF
15 PSF
30 PSF
35 PSF
20 PSF
450 Series Storefront
450 Series Storefront
Part # - 450 & 451
STANDARD ALUMINUM PRODUCTS INC.
Storefront System450 Series Flushed Glazed
B-3SCALE 1/2 FULL SIZE
450 Series - Profiles
557
558
459
456
458
450
451
454
453
452
455
559
S553
457
9 2
5
3
STANDARD ALUMINUM PRODUCTS INC.
450 Series Flushed Glazed
6
8
Jamb1 Vertical2
4
4 1
/2
"
1 3/4"
Storefront System
1
11
4m
m
45mm45mm
1 3/4"
7
B-4SCALE 1/2 FULL SIZE
450
450
451
7
5 Sill
STANDARD ALUMINUM PRODUCTS INC.
Head With Deflection6
Horizontal4
3
1 3
/4
"
4 1/2"
Storefront System450 Series Flushed Glazed
45
mm
114mm
SCALE 1/2 FULL SIZE
B-5
450
455
454
Head
454
453
458
450
7 Sill With Subsill
S553
454
453
7
450 Series Flushed GlazedSTANDARD ALUMINUM PRODUCTS INC.
90° Corner8
135° Corner
4 1/2"
4 1
/2
"
4 1
/2
"
Storefront System
11
4m
m
114mm
2
1
/
4
"
B-6SCALE 1/2 FULL SIZE
451
451
559
11
4m
m
557
558
459
5
7
m
m
STANDARD ALUMINUM PRODUCTS INC.
450 Series
19mm
Steel Reinforcing
45mm
1 3/4"
3/4"
4"
10
1m
m
12 Gauge Steel
Steel Reinforcing9
B-7SCALE 1/2 FULL SIZE
451
450
4 1
/2
"
1 3/4"
2 Door Jamb With Sidelite
2Rev.
11
4m
m
1 3/4"
45mm
45mm
450 Series Flushed GlazedStorefront System
STANDARD ALUMINUM PRODUCTS INC.
B-8SCALE 1/2 FULL SIZE
456
450
456
451
450
Door Jamb 1
4
5
21
3
1
4
Rev.
1/8"
3mm
STANDARD ALUMINUM PRODUCTS INC.
Threshold4
Door Head3
Door Head With Transom5
1 3
/4
"
4 1/2"
450 Series Flushed GlazedStorefront System
114mm
45
mm
B-9
450
SCALE 1/2 FULL SIZE
454
455
1/8"
3mm
3
16
"
SCALE 1/2 FULL SIZE
Design
The system shall be 4 ½” x 2” center line flush
glazing and accommodate glass from 22mm to
25mm thick. The system can be glazed from
interior or exterior and is dry glaze.
Performance
See Wind load Charts.
Structural performance shall conform to CSA
Standard CAN3-S157 “Strength design in
Aluminum” and a maximum deflection of 1/175 of
the span.
Material
Extrusions shall be 6063 alloy and T5 Temper.
Glazing gaskets shall be EPDM elastomeric
extrusions.
Finish
Both anodized and painted finishes are available.
All integral colour anodizing is Architectural Class
II., 0.4 to 0.7 mm coating. A fluropolymer paint
coating conforming to the requirements of AAMA
603 and AAMA 605 specifications, the toughest
coating in the industry standards.
Testing
All testing shall be on full size frame sections. Air
infiltration shall be tested in accordance with
ASTM-Designation E283-91 or ASHRAE
standards #90-80
Fabrication
Framing should be fabricated from extrusions of
size and shape in accordance with shop
drawings. The framing system shall provide for
flush glazing while maintaining the 2” nominal
face dimensions.
The 550 Series has a complete number of
sections including deflection header and
extruded sub sill runner that can satisfy any
design requirements.
Construction
Frames shall have mechanically joined corners
with no exposed screws. All joints shall be
accurately fitted free of burrs and rough edges.
Complete frame assemblies shall be free of
warp. Each type of entrance framing systems is
compatible with all Standard Aluminum swing
doors and sliding mall fronts.
Installation
Experienced technicians in accordance with
approved shop drawings shall install all frames.
The frames shall be set plumb, square, and level
and in correct alignment and adjacent
construction. All anchoring shall suit the type of
construction of the perimeter work.
Protection and Cleaning
After installation the general contractor should
adequately protect the exposed aluminum and
glass surfaces from damage by other trades.
i.e.(but not restricted to) cement splash and
leach, grinding, polishing compounds, plaster,
paint, lime, acids and other contaminants.
550 Series Flushed GlazedSpecification
STANDARD ALUMINUM PRODUCTS INC.
B-10
STANDARD ALUMINUM PRODUCTS INC.
550 Series Flushed GlazedWind Loads
B-11SCALE 1/2 FULL SIZE
Calculations are based on CAN3-S157-M83 "Strength Design In Aluminum" using
6063-T5 Alloy-Temper, and a Deflection Limit = Span/175
2
5
6
7
8
9
10
11
12
13
14
15
3 4 5 6 8
Height (Feet)
Module Width, (Feet)
550 Series Storefront
2
7
8
9
10
11
12
13
14
15
16
18
3 4 5 6 8
Height (Feet)
Module Width, (Feet)
7
17
19
20
7
25 PSF
15 PSF
30 PSF
35 PSF
20 PSF
25 PSF
15 PSF
30 PSF
35 PSF
20 PSF
Part # - 550 & 551
c/w 12 Gauge Reinforcing
550 Series Storefront
Part # - 550 & 551
550 Series Flushed GlazedSTANDARD ALUMINUM PRODUCTS INC.
SCALE 1/2 FULL SIZE
Storefront System
B-12
550 Series - Profiles
557
558
458
555
554
553
452
551
550556
559
S553
550 Series Flushed GlazedSTANDARD ALUMINUM PRODUCTS INC.
1 Jamb
4 1
/2
"
Vertical2
1 2
5
4
3 6
87
Storefront System
11
4m
m
2"
51mm 51mm
9
SCALE 1/2 FULL SIZE
550
2"
B-13
550
551
7
STANDARD ALUMINUM PRODUCTS INC.
5
3
Sill
Head
4 Horizontal
555
4 1/2"
2"
6 Head With Deflection
550 Series Flushed GlazedStorefront System
51
mm
114mm
B-14
550
SCALE 1/2 FULL SIZE
554
554
553
458
550
7 Sill With Subsill
554
553
S553
4 1/2"
4 1
/2
"
90° Corner
135° Corner
4 1
/2
"
11
4m
m
11
4m
m
114mm
2
1
/
4
"
550 Series Flushed GlazedSTANDARD ALUMINUM PRODUCTS INC.
B-15
559
557
8
7
Storefront System
SCALE 1/2 FULL SIZE
551
551
558
5
7
m
m
Steel Reinforcing550 Series
STANDARD ALUMINUM PRODUCTS INC.
2"
51mm
3/4"
10
1m
m
4"
19mm
12 Gauge Steel
Steel Reinforcing9
B-16SCALE 1/2 FULL SIZE
551
550
4 1
/2
"
2
2"
Door Jamb 1
3
4
1 2
4
1
5
STANDARD ALUMINUM PRODUCTS INC.
Door Jamb With Sidelite
550 Series Flushed GlazedStorefront System
51mm
11
4m
m
51mm
2"
Rev.2Rev.
B-17SCALE 1/2 FULL SIZE
550
556 556
550
551
1/8"
3mm
STANDARD ALUMINUM PRODUCTS INC.
4 1/2"
Threshold4
Door Head3
Door Head With Transom
550 Series Flushed GlazedStorefront System
5
51
mm
114mm
B-18SCALE 1/2 FULL SIZE
550
556
556
555
554
2"
1/8"
3mm
3
16
"
STANDARD ALUMINUM PRODUCTS INC.
B-19
550T Series Flushed GlazedSpecification
STANDARD ALUMINUM PRODUCTS INC.
B-20SCALE 1/2 FULL SIZE
Design
The system shall be 4 ½” x 2 1/4” Thermally
Broken center line flush glazing and accommodate
glass from 22mm to 25mm thick. The system can
be glazed from interior or exterior and is dry glaze.
Performance
See Wind load Charts.
Structural performance shall conform to CSA
Standard CAN3-S157 “Strength design in
Aluminum” and a maximum deflection of 1/175 of
the span.
Material
Extrusions shall be 6063 alloy and T5 Temper.
Glazing gaskets shall be EPDM elastomeric
extrusions.
Finish
Both anodized and painted finishes are available.
All integral colour anodizing is Architectural Class
II., 0.4 to 0.7 mm coating. A fluropolymer paint
coating conforming to the requirements of AAMA
603 and AAMA 605 specifications, the toughest
coating in the industry standards.
Testing
All testing shall be on full size frame sections. Air
infiltration shall be tested in accordance with
ASTM-Designation E283-91 or ASHRAE
standards #90-80
Fabrication
Framing should be fabricated from extrusions of
size and shape in accordance with shop
drawings. The framing system shall provide for
flush glazing while maintaining the 2 1/4” nominal
face dimensions.
The 550 Series has a complete number of
sections including deflection header and
extruded sub sill runner that can satisfy any
design requirements.
Construction
Frames shall have mechanically joined corners
with no exposed screws. All joints shall be
accurately fitted free of burrs and rough edges.
Complete frame assemblies shall be free of
warp. Each type of entrance framing systems is
compatible with all Standard Aluminum swing
doors and sliding mall fronts.
Installation
Experienced technicians in accordance with
approved shop drawings shall install all frames.
The frames shall be set plumb, square, and level
and in correct alignment and adjacent
construction. All anchoring shall suit the type of
construction of the perimeter work.
Protection and Cleaning
After installation the general contractor should
adequately protect the exposed aluminum and
glass surfaces from damage by other trades.
i.e.(but not restricted to) cement splash and
leach, grinding, polishing compounds, plaster,
paint, lime, acids and other contaminants.
STANDARD ALUMINUM PRODUCTS INC.
Wind Loads550T Series Flushed Glazed
B-21SCALE 1/2 FULL SIZE
Calculations are based on CAN3-S157-M83 "Strength Design In Aluminum" using
6063-T5 Alloy-Temper, and a Deflection Limit = Span/175
2
5
6
7
8
9
10
11
12
13
14
15
3 4 5 6
Height (Feet)
Module Width, (Feet)
25 PSF
15 PSF
30 PSF
35 PSF
20 PSF
550T Series Storefront
7
40 PSF
16
17
18
8 2
5
6
7
8
9
10
11
12
13
14
15
3 4 5 6
Module Width, (Feet)
7
16
17
18
8
550T Series Storefront
19 19
c/w 10 Gauge Reinforcing
Part # - 550T & 551T
Part # - 550T & 551T
550T Series Flushed GlazedSTANDARD ALUMINUM PRODUCTS INC.
SCALE 1/2 FULL SIZE
Storefront System
B-22
550T Series - Profiles
556
458T
550T
555T
554
551T
553T
557T
558T
456456T
559T
S553T
STANDARD ALUMINUM PRODUCTS INC.
4
1 2
4
5
8
3
7
6
1 Vertical2
550T Series Flushed Glazed
4 1
/2
"
2 1/4"
B-23SCALE 1/2 FULL SIZE
550T
551T
Jamb
Storefront System
57mm
2 1/4"
11
4m
m
57mm
550T
9
7
STANDARD ALUMINUM PRODUCTS INC.
554
555T
553T
554
Head3
Horizontal4
Sill5
Head With Deflection6
4 1/2"
550T Series Flushed GlazedStorefront System
114mm
2 1
/4
"
57
mm
B-24SCALE 1/2 FULL SIZE
550T
458T
550T
554
553T
Sill With Subsill5
S553T
STANDARD ALUMINUM PRODUCTS INC.
4 1
/2
"
7 135° Corner
8 90° Corner
4 1
/2
"
4 1/2"
Storefront System550T Series Flushed Glazed
11
4m
m
114mm
11
4m
m
2
1
/
4
"
B-25SCALE 1/2 FULL SIZE
559T
551T
551T
557T
558T
5
7
m
m
STANDARD ALUMINUM PRODUCTS INC.
Vertical c/w Steel Reinforcing9
550T Series Flushed Glazed
2 1/4"
B-26SCALE 1/2 FULL SIZE
551T
Storefront System
57mm
550T
1
1 4
"
1
1
2
"
38mm
32
mm
Steel Reinforcing
10 Gauge Steel
21
4
3
1
4
5
4 1
/2
"
57mm
11
4m
m
2 1/4"
57mm
2 1/4"
Door Jamb With Sidelite2Door Jamb1
Rev. 2 Rev.
550T Series Flushed GlazedStorefront System
STANDARD ALUMINUM PRODUCTS INC.
B-27SCALE 1/2 FULL SIZE
556
550T
550T
551T
556
1/8"
3mm
1/8"
3mm
STANDARD ALUMINUM PRODUCTS INC.
556
Threshold4
Door Head3
550T Series Flushed GlazedStorefront System
Door Head With Transom5
4 1/2"
114mm
2 1
/4
"
57
mm
B-28SCALE 1/2 FULL SIZE
556
550T
555T
556
554
1/8"
3mm
3
16
"
1/8"
3mm
21
4
3
1
6
5
4 1
/2
"
57mm
11
4m
m
2 1/4"
57mm
2 1/4"
Door Jamb With Sidelite2Door Jamb1
Rev. 2 Rev.
550T Series Flushed Glazed c/w 200T DoorStorefront System
STANDARD ALUMINUM PRODUCTS INC.
B-29SCALE 1/2 FULL SIZE
550T
550T
551T
456
456T
PIVOT JAMB
456
456T
LOCKING JAMB
46
1/8"
3mm
1/8"
3mm
STANDARD ALUMINUM PRODUCTS INC.
Threshold4
Door Head3
550T Series Flushed Glazed c/w 200T DoorStorefront System
4 1/2"
114mm
2 1
/4
"
57
mm
B-30SCALE 1/2 FULL SIZE
550T
456
456T
1/8"
3mm
3
16
"
STANDARD ALUMINUM PRODUCTS INC.
550T Series Flushed Glazed c/w 200T Door
B-31SCALE 1/2 FULL SIZE
Door Head With Transom5
555T
554
4 1/2"
114mm
456
456T
Threshold6
1/8"
3mm
3
16
"
STANDARD ALUMINUM PRODUCTS INC.
Adjustable BaseSash & Stop
3 1
/2
"
5/8
"
Double Glazed
100-02 Double GlazedSection
100-01 Single GlazedSection
Adjustable BaseAdjustable BaseSingle Glazed
B-32SCALE 1/2 FULL SIZE
3 1
/2
"
2 3
/8
"3
/4
"
#835
#855
#855
#835
2 3
/8
"
1 3/4"
1"
1 3/4"
1"
2mm
1/16"
2mm
1/16"
2mm
1/16"
2mm
1/16"
U-ChannelsSTANDARD ALUMINUM PRODUCTS INC.
1100 7575
1225
5750
1"
25mm
2 1
/4
"
57
mm
1/8"
3mm
1/8"
3mm
25mm
1"
1"
25
mm
3/4
"
19
mm
3/4"
19mm
3/4
"
19
mm
1/2"
13mm
5/8"
3/8"
5/8"
5/8"
B-33
5050
1/2
"
13
mm
13mm
1/2"
3/8"
3/4
"
7575A
19
mm
3/4"
19mm
SCALE - FULL SIZE
2mm
1/16"
7510
1"
25
mm
3/4"
19mm
5/8"
Miscellaneous TubingSTANDARD ALUMINUM PRODUCTS INC.
175450
1 3
/4
"
44
mm
44mm
1 3/4"
175175
1 3/4"
44mm
4 1
/2
"
11
4m
m
2.5mm
.100"
4"
.100"
175400
2.5mm
10
2m
m
1 3/4"
44mm
B-34SCALE - FULL SIZE
.100"
2.5mm