selection of sensors (mechatronics)
TRANSCRIPT
![Page 1: Selection of sensors (mechatronics)](https://reader033.vdocument.in/reader033/viewer/2022042605/58e65fcb1a28ab8d758b5013/html5/thumbnails/1.jpg)
Konstruktiotekniikka
Mechatronics Components and Instrumentation(MSc Course: EDE-31206)
Selection of Sensors
Mithun ChowdhuryTomáš Spáčil
16/11/2013
![Page 2: Selection of sensors (mechatronics)](https://reader033.vdocument.in/reader033/viewer/2022042605/58e65fcb1a28ab8d758b5013/html5/thumbnails/2.jpg)
Konstruktiotekniikka
DESIGN PROCESS
Distinguish into 6 major phases• Conceptual design• Preliminary design• Detail design and development• Construction• Operation use• Retirement
Sensors are necessarily part of almost all phases
![Page 3: Selection of sensors (mechatronics)](https://reader033.vdocument.in/reader033/viewer/2022042605/58e65fcb1a28ab8d758b5013/html5/thumbnails/3.jpg)
Konstruktiotekniikka
REQUIREMENTS Summarizing possible future application of the system
Measurement principles• Environment• Size, weight
Sensing method• Resolution, range, frequency,...• Output• Cost
Best compromise
![Page 4: Selection of sensors (mechatronics)](https://reader033.vdocument.in/reader033/viewer/2022042605/58e65fcb1a28ab8d758b5013/html5/thumbnails/4.jpg)
Konstruktiotekniikka
SENSOR x TRANSDUCER
Sensor produce a signal relating to the physical quantity being measured.
Transducer converts one type of energy to another form of energy.• Transducer consists of a sensor and electronic circuit.• Output from of a transducer is normally voltage (V) or current (A).
![Page 5: Selection of sensors (mechatronics)](https://reader033.vdocument.in/reader033/viewer/2022042605/58e65fcb1a28ab8d758b5013/html5/thumbnails/5.jpg)
Konstruktiotekniikka
ROTATIONAL• Potentiometer• Resolvers• Magnetic / optical encoders• Capacitive encoders• Inductive encoders
![Page 6: Selection of sensors (mechatronics)](https://reader033.vdocument.in/reader033/viewer/2022042605/58e65fcb1a28ab8d758b5013/html5/thumbnails/6.jpg)
Konstruktiotekniikka
TEMPERATURE
![Page 7: Selection of sensors (mechatronics)](https://reader033.vdocument.in/reader033/viewer/2022042605/58e65fcb1a28ab8d758b5013/html5/thumbnails/7.jpg)
Konstruktiotekniikka
MAGNETIC• Hall sensor• Magnetoresistive sensor• Magnetodiode• Induction coil• SQUID
![Page 8: Selection of sensors (mechatronics)](https://reader033.vdocument.in/reader033/viewer/2022042605/58e65fcb1a28ab8d758b5013/html5/thumbnails/8.jpg)
Konstruktiotekniikka
Sensor Topology
Sensitivity Range Precision Resolution Accuracy Offset Linearity Hysteresis Response Time Dynamic Linearity
![Page 9: Selection of sensors (mechatronics)](https://reader033.vdocument.in/reader033/viewer/2022042605/58e65fcb1a28ab8d758b5013/html5/thumbnails/9.jpg)
Konstruktiotekniikka
Sensitivity• defined as the input parameter change required to produce a
standardized output change
Range• is the maximum and minimum values of applied parameter that can be
measured
Precision• refers to the degree of reproducibility of a measurement
Resolution• is the smallest detectable incremental change of input parameter that
can be detected in the output signal.
Sensor Topology
![Page 10: Selection of sensors (mechatronics)](https://reader033.vdocument.in/reader033/viewer/2022042605/58e65fcb1a28ab8d758b5013/html5/thumbnails/10.jpg)
Konstruktiotekniikka
Accuracy• maximum difference that will exist between the actual value (which
must be measured by a primary or good secondary standard) and the indicated value at the output of the sensor
Linearity• is an expression of the extent to which the actual measured curve of a
sensor departs from the ideal curve.
Response Time• Sensors do not change output state immediately when an input
parameter change occurs. Rather, it will change to the new state over a period of time, called the response time.
Sensor Topology
![Page 11: Selection of sensors (mechatronics)](https://reader033.vdocument.in/reader033/viewer/2022042605/58e65fcb1a28ab8d758b5013/html5/thumbnails/11.jpg)
Konstruktiotekniikka
Choose the Right Sensor for an Measurement System
Depend on Temperature Strain Sound Vibration Position and Displacement Pressure Force
![Page 12: Selection of sensors (mechatronics)](https://reader033.vdocument.in/reader033/viewer/2022042605/58e65fcb1a28ab8d758b5013/html5/thumbnails/12.jpg)
Konstruktiotekniikka
Mechatronics Components and Instrumentation(MSc Course: EDE-31206)
Thanks for your attention!
Mithun ChowdhuryTomáš Spáčil
16/11/2013