self adhesive molding - b-d company | serving the...
TRANSCRIPT
B-D Company Section 5 - Page 1 303.744.1405 www-b-dco.com 1.800.748.2244
MANUFACTURER & DISTRIBUTOR OF FINE AUTOMOTIVE PRODUCTS
Your One Stop Shop For Specialty Automotive Products
Self Adhesive Molding
Factory and Universal Styles -Sold by the Foot or as a Kit-
Vinyl Extruded Self Adhesive 3M
Automotive Tape
1360 S. Acoma St. Denver, CO. 80223
303.744.1405 800.748.2244
www.b-dco.com
B-D Company Section 5 - Page 2 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Table of Contents
Body Side Molding Instructions Black Body Side Molding Chrome Body Side Molding Gold Body Side Molding Black & Chrome Body Side Molding Ribbed Body Side Molding Door Edge Guard Color Kit Body Side Molding Wheel Well Molding Trim-Gard Catalog - Special Order - Call For Availability Rivet-On Molding Body Side Molding Tools
3
4 - 5
6 - 7
8
8 - 10
11
12 - 14
15
16 - 17
18 - 23
24
25
B-D Company Section 5 - Page 3 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Installation Instructions
TO ACHIEVE BEST RESULTS THE FOLLOWING PROCEDURES MUST BE FOLLOWED
READ CAREFULLY BEFORE STARTING
CLEAN SURFACE - The area where the molding is to be applied should be free of wax,
dirt, or foreign substances. Use PRO-CLEAN for best results.
SURFACE TEMPERATURE - The surface where molding is to be installed should be at least 75 Degrees F for proper adhesion. If needed, the surface can be warmed with any
type of heat gun.
ADHESION PORMOTER - Just prior to installation, a light coat of PROBOND Adhesion Promoter should be applied to the surface area where moldings will adhere,
to provide permanent bonding aggression.
WARM MOLDINGS - Lightly use a heat gun or a heat box to warm moldings if they are cold and inflexible. Storage in a warm area will prevent molding from becoming stiff.
CAUTION: Too much localized heat will wrinkle chrome surfaces.
INSTALLATION - To start, cut your molding for your beginning point to the proper angle using pruning shears. Peel back the poly liner from the adhesive about 18" and apply the molding along your desired line. Continue the peel and apply steps, being careful not to touch or allow the exposed adhesive to get dirty, until your installation is complete. Once the molding has been applied, use a soft clean cloth to apply pressure along the surface
of the molding, to assure maximum and uniform adhesion.
NOTE: The sharp cutting edge should always be against the chrome side of the molding, with the adhesive liner side against the anvil. When the molding is cut upside down, the
anvil will crush the chrome side and destroy the adhesive bonds between the chrome and the material.
NOTE: AFTER INSTALLATION IS COMPLETED, APPLY A COAT OF PRO-SEAL TO
EVERY CUT THAT HAS BEEN MADE. THIS SEAL COAT MUST COVER THE SURFACE AREA OF THE CUT ALONG WITH A SLIGHT, BUT POSITIVE, OVERLAP OF
THE CHROME. This will prevent degradation due to severe weathering.
B-D Company Section 5 - Page 4 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Solid Black Molding
PART # SOLD
BBR By The Foot
BBR20 In a 20’ Kit
BBR90 In a 90’ Roll
PART # SOLD
B650 By The Foot
B65050 In a 50’ Roll
PART # SOLD
DMB By The Foot
DMB60 In a 60’ Roll
PART # SOLD
BL By The Foot
BL60 In a 60’ Roll
PART # SOLD
BLHR By The Foot
BLHR20 In a 20’ Kit
BLHR50 In a 50’ Roll
⅜" Flat Top Black Molding
⅝" Flat Top Black Molding
⅝" Cantilever Black Molding
¼" Half Round Black Molding
⅜" Half Round Black Molding
PART # SOLD
450 By The Foot
4506002 In a 60’ Roll
⅝" "High-Top" Black Embossed Molding
B-D Company Section 5 - Page 5 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Solid Black Molding
PART # SOLD
ES150 By The Foot
ES15065 In a 65’ Roll
PART # SOLD
ES138 By The Foot
ES138100 In a 100’ Roll
1⅜" Half Round Black Molding
PART # SOLD
GM10B By The Foot
GM10B34 In a 34’ Kit
GM10B65 In a 65’ Roll
2⅜" GMC Molding
PART # SOLD
LS170 By The Foot
LS17042 In a 42’ Roll
1¾" LeSabre Black Molding
PART # SOLD
ES2100 By The Foot
ES210065 In a 65’ Roll
2" Matte Black Molding
1½" Matte Black Molding
PART # SOLD
ES126 By The Foot
ES12626 In a 26’ Roll
ES12660 In a 60’ Roll
1" Matte Black Standard Molding
B-D Company Section 5 - Page 6 303.744.1405 www-b-dco.com 1.800.748.2244
PART # SOLD
ABR By The Foot
ABR90 In a 90’ Roll
Body Side Molding - Solid Chrome Molding
¼" Half Round Chrome Molding
⅜" Flat Top Chrome Molding
⅝" Flat Top Chrome Molding
⅝" Deluxe Chrome Molding
¾" Standard Chrome Molding
PART # SOLD
AB By The Foot
AB60 In a 60’ Roll
PART # SOLD
AB650 By The Foot
AB65050 In a 50’ Roll
PART # SOLD
DMC By The Foot
DMC60 In a 60’ Roll
PART # SOLD
AB825 By The Foot
AB82560 In a 60’ Roll
PART # SOLD
ABHR By The Foot
ABHR20 In a 20’ Kit
ABHR50 In a 50’ Roll
⅜" Half Round Chrome Molding
B-D Company Section 5 - Page 7 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Solid Chrome Molding
PART # SOLD
AB1750 By The Foot
AB175065 In a 65’ Roll
PART # SOLD
VT125 By The Foot
VT12565 In a 65’ Roll
PART # SOLD
VT200 By The Foot
VT20034 In a 34’ Kit
VT20065 In a 65’ Roll
PART # SOLD
AB100 By The Foot
AB10060 In a 60’ Roll
1" Solid Chrome Molding
1¼" Chrome Molding
2" Chrome Molding
1¾" Solid Chrome Molding
PART # SOLD
SLV220 By The Foot
SLV22034 In a 34’ Roll
SLV22065 In a 65’ Roll
2¼" Chrome Molding
B-D Company Section 5 - Page 8 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Solid Gold Molding
PART # SOLD
DMG By The Foot
DM100G In a 100' Roll
PART # SOLD
GB By The Foot
GB60 In a 60' Roll
⅜" Solid Gold Molding
⅝" Solid Gold Molding
PART # SOLD
1937 By The Foot
19376502 In a 65' Roll
PART # SOLD
1211 By The Foot
12116002 In a 60' Roll
⅞" Black & Chrome Molding
1¼" Black & Chrome Molding
PART # SOLD
724 By The Foot
7246002 In a 60' Roll
⅝" Black & Chrome Molding
Body Side Molding - Black & Chrome Molding
B-D Company Section 5 - Page 9 303.744.1405 www-b-dco.com 1.800.748.2244
PART # SOLD
FT92 By The Foot
FT9266 In a 66’ Roll
PART # SOLD
S260 By The Foot
S26019 In a 19’ Kit
S26058 In a 58’ Roll
2" Ford Truck Molding
2⅛" GMC Molding
PART # SOLD
VT20002 By The Foot
VT2003402 In a 34’ Kit
VT2006502 In a 65’ Roll
2" Van & Truck Molding
Body Side Molding - Black & Chrome Molding
PART # SOLD
PDC By The Foot
PDC20065 In a 65’ Roll
1⅞" Chrysler/Dodge Molding
PART # SOLD
DRC By The Foot
DRC19042 In a 42’ Roll
1¾" Dodge Ram Molding
PART # SOLD
F234 By The Foot
F23445 In a 45’ Roll
1¾" Ford Truck Molding
B-D Company Section 5 - Page 10 303.744.1405 www-b-dco.com 1.800.748.2244
PART # SOLD
S94 By The Foot
S9419 In a 19’ Kit
S9458 In a 58’ Roll
PART # SOLD
S98 By The Foot
S9858 In a 58' Roll
3" GMC Truck Molding
3⅛" GMC Truck Molding
PART # SOLD
SLV99 By The Foot
SLV9918 In a 18' Kit
SLV9954 In a 54' Roll
3⅞" Silverado Truck Molding
Body Side Molding - Black & Chrome Molding
PART # SOLD
FT97 By The Foot
FT9766 In a 66’ Roll
3" Ford Truck Molding
2½" Ford Truck Molding
PART # SOLD
GM10C By The Foot
GM10C34 In a 34’ Kit
GM10C65 In a 65’ Roll
2⅜" GMC Molding
PART # SOLD
FT300 By The Foot
FT30022 In a 22' Roll
FT30044 In a 44' Roll
B-D Company Section 5 - Page 11 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Ribbed Molding
PART # SOLD
RBC By The Foot
RBC5002 In a 50' Roll
1¼" Black & Chrome Ribbed
PART # SOLD
RK By The Foot
RK20065 In a 65' Roll
2" Black Ribbed Molding
PART # SOLD
RB By The Foot
RB5002 In a 50' Roll
RB15002 In a 150' Roll
1¼" Black Ribbed Molding
2⅜" Black Ribbed Molding
PART # SOLD
RB237 By The Foot
Limited to Stock
B-D Company Section 5 - Page 12 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Door Edge Guard
PART # SOLD
DGB400 By The Foot
DG50B400 In a 50' Roll
DG150B400 In a 150' Roll
PART # SOLD
DG-CLR By The Foot
DG50CLR In a 50' Roll
DG150CLR In a 150' Roll
PART # SOLD
DGB By The Foot
DG50B-R In a 50' Roll
DG150B-R In a 150' Roll
Standard ¼" Matte Black Door Edge Guard
Large ⅜" Matte Black Door Edge Guard
Heavy Duty ½" Matte Black Door Edge Guard
PART # SOLD
EG By The Foot
EG6002 In a 60' Roll
Standard ¼" Clear Door Edge Guard
Standard ¼" Chrome Door Edge Guard
Large ⅜" Chrome Door Edge Guard
PART # SOLD
DGC By The Foot
DG50C-R In a 50' Roll
DG150C-R In a 150' Roll
PART # SOLD
TRI/21 By The Foot
TRI/21-50 In a 50' Roll
TRI/21-150 In a 150' Roll
B-D Company Section 5 - Page 13 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Door Edge Guard
PART # SOLD
DGG By The Foot
DG50G In a 50' Roll
Standard ¼" Gold Door Edge Guard
Standard ¼" High Gloss Door Edge Guard
PART # SOLD
DG20-HG By The Foot
DG5020-HG In a 50' Roll
Bright Red
PART # SOLD
DG42-HG By The Foot
DG5042-HG In a 50' Roll
Silver
PART # SOLD
DG13-HG By The Foot
DG5013-HG In a 50' Roll
White
PART # SOLD
DG02-HG By The Foot
DG5002-HG In a 50' Roll
Black
½" 'L'-Shaped Matte Black Door Edge Guard with 3M® Tape
PART # SOLD
DGAB By The Foot
DGA20B-R In a 20' Kit
DGA50B-R In a 50' Roll
PART # SOLD
DGA33 By The Foot
DGA3350-R In a 50' Roll
Beige
½" 'L'-Shaped Door Edge Guard with 3M® Tape
PART # SOLD
DGA16 By The Foot
DGA1650-R In a 50' Roll
Dk. Maple
PART # SOLD
DGA18 By The Foot
DGA1850-R In a 50' Roll
Lt. Maple
B-D Company Section 5 - Page 14 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Door Edge Guard
PART # SOLD
DGAC By The Foot
DGA20C-R In a 20' Kit
DGA50C-R In a 50' Roll
⅜" Matte Black "Slimline" Door Edge Guard
½" 'L'-Shaped Chrome Door Edge Guard with 3M® Tape
PART # SOLD
DGB-AR By The Foot
DG50B-AR In a 50' Roll
PART # SOLD
DGAR20 By The Foot
DGAR5020-HG In a 50' Roll
Red
⅜" High Glass "Slimeline" Door Edge Guard
PART # SOLD
DGAR13 By The Foot
DGAR5013-HG In a 50' Roll
White
PART # SOLD
DGAR40 By The Foot
DGAR5040-HG In a 50' Roll
Charcoal
PART # SOLD
DGAR02 By The Foot
DGAR5002-HG In a 50' Roll
Black
PART # SOLD
DGAR42 By The Foot
DGAR5042-HG In a 50' Roll
Silver
B-D Company Section 5 - Page 15 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Kits with Tips
⅝" Universal Molding Kit with 4 ends
2 Pieces - 13' Long
PART # COLOR
724K02 Black
724K04 White
724K06 Dk. Blue
724K10 Lt. Blue
724K16 Dk. Maple
724K24 Dk. Brown
724K28 Buckskin
724K40 Charcoal Met.
724K42 Silver
⅞" Universal Molding Kit with 4 ends
2 Pieces - 13' Long PART # COLOR
1937K02 Black
1937K04 White
1937K06 Dk. Blue
1937K10 Lt. Blue
1937K16 Dk. Maple
1937K24 Dk. Brown
1937K28 Buckskin
1937K42 Silver
1¼" Universal Molding Kit with 4 ends
2 Pieces - 13' Long PART # COLOR
1211K02 Black
1211K04 White
1211K06 Dk. Blue
1211K16 Dk. Maple
1211K28 Buckskin
1211K42 Silver
B-D Company Section 5 - Page 16 303.744.1405 www-b-dco.com 1.800.748.2244
½" Matte Black Wheel Well Molding PART # SOLD
W601B By The Foot
W601B20 In a 20' Kit
W601B125 In a 125' Roll
Body Side Molding - Wheel Well Molding
PART # SOLD
W716B By The Foot
W716B20 In a 20' Kit
W716B150 In a 150’ Roll
7⁄ 16" Matte Black Half Round Wheel Well Molding
7⁄ 16" High Gloss Half Round Wheel Well Molding
PART # SOLD
W71616 By The Foot
W7165016-HG In a 50' Roll
Dk. Maple
PART # SOLD
W71613 By The Foot
W7165013-HG In a 50' Roll
White
PART # SOLD
W71620 By The Foot
W7165020-HG In a 50' Roll
Bright Red
PART # SOLD
W71602 By The Foot
W7165002-HG In a 50' Roll
Black
PART # SOLD
W71642 By The Foot
W7165042-HG In a 50' Roll
Silver
PART # SOLD
W702B By The Foot
W702B20 In a 20' Kit
W702B100 In a 100' Roll
½" Matte Black Wheel Well Molding with Lip
B-D Company Section 5 - Page 17 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Wheel Well Molding
PART # SOLD
W801G20 In a 20' Kit
½" Chrome Wheel Well Molding with Lip
PART # SOLD
W402C By The Foot
W402C20 In a 20’ Kit
W402C100 In a 100’ Roll
½" Chrome Wheel Well Molding
PART # SOLD
W501C By The Foot
W501C20 In a 20’ Kit
W501C125 In a 125’ Roll
½" Gold Wheel Well Molding
B-D Company Section 5 - Page 18 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Trim Gard Special Order Moldings
500 - Series 501 - All Chrome Colors Available
800 - Series 801 - All Chrome Colors Available
1300 - Series 1301 - All Chrome Colors Available
PP01 - All Chrome
PP02 - Chrome & Black
CMV01 - All Chrome CMV02 - Black
Actual products are later than illustrated
C600 - Series Colors Available
602 - Black
PC02 - Black
CM44 - Series Colors Available
8002E - Black (Embossed) 8002S - Black (Smooth
FN - Series Color Available: 02, 04, 14, 47, 80, 84
2502E - Black (Embossed) 2502S - Black (Smooth)
1102NT - Black 1102WC - Black & Chrome
1002NT - Black 1002WC - Black & Chrome
11702 - Black & Chrome 11702R - Black & Red
CV-02WC - CV88-02NT - Blacvk Black & Chrome
CV92 - Black
COLORS: GROUP A - See Page 21
01 - Chrome 14 - Silver 80 - Bright Red 02 - Black 20 - Dk Autumn Metallic 81 - Champagne Silver Metallic 04 - White 29 - Chestnut 84 - Dark Charcoal 05 - Dark Blue 34 - Liquid Silver 85 - Rally Blue 06 - Gold 35 - Midnight Blue 90 - Absolute Red 07 - Dark Green 45 - Silver Blue Metallic 91 - Camel Beige 08 - Adobe Beige 47 - Emerald Green 95 - Spectra Blue 10 - Dark Red 64 - Dark Silver 99 - Natural (paintable)
B-D Company Section 5 - Page 19 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Trim Gard Special Order Moldings
TCT11 - Black & Chrome TCT11NT - Black (Embossed)
99CT - Black & Chrome Colors: 02, 04, 64, 81
98DT - Black; K1 or K2 (Pre-cut kits)
S10 - Black & Chrome
94S10 - Black & Chrome
T11WC - Black & Chrome ET11WC - Black & T11NT - Black Chrome (Embossed) T1184WC - Charcoal & ET11NT - Black Chrome (Embossed)
98S10 - Black & Chrome
94DT - Black & Chrome
2001 - Chrome 2002 - Black & Chrome
9001 - Chrome 9002 - Black & Chrome
99GT - 01 Chrome 99GT - 02 Black
GMAV - Dark Silver & Chrome
F150 - Black & Chrome
FD92 - Black & Chrome FD94 - White & Chrome
FD97 - Black & Chrome Colors Available: 02, 04, 64
FD02 - Black
B-D Company Section 5 - Page 20 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Trim Gard Special Order Moldings
BT00DC SERIES Color Group "B" High Gloss
Packaged in two 8ft lengths with die cut tips on all ends
BT01 - Chrome Roll Stock
BT00 SERIES Color Group "B" High Gloss Packaged in two 8ft lengths with formed tips on all ends
1400DC SERIES Color Group "B" High Gloss
Packaged in two 7ft lengths with die cut tips on all ends
1401 - Chrome Roll Stock
1400BT SERIES Color Group "B" High Gloss Packaged in two 7ft lengths with formed tips on all ends
1500DC SERIES Color Group "B" High Gloss
Packaged in two 8ft lengths with die cut tips on all ends
1500AT SERIES Color Group "B" High Gloss Packaged in two 8ft lengths with formed tips on all ends
CV96DC SERIES Colors: 02, 04, 31, 64,, 99
Packaged in a four-piece kit with die cut tips
BT01 - Chrome Roll Stock
CV96 SERIES Colors: 02, 04, 34, 64, 99 Packaged in a four-piece kit with formed tips
Color 99 is a natural color suitable for paint applications
NC00 - Clear NC02 -Black
22L - Black
21 - Chrome 22 -Black 401 - Chrome 402 - Black Colors Available
B-D Company Section 5 - Page 21 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Trim Gard Special Order Moldings
B-D Company Section 5 - Page 22 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Trim Gard Special Order Moldings
EP02WC - Black & Chrome EP02NT - Black 1" (2.54 cm)
9702 - Black 1⅛" (2.86 cm)
SS02 - Black 2" (5.08 cm)
ST200NL - Black 2" (5.08 cm)
STWL - Series Black (With lip) 3" (7.62 cm) - 6" (15.24 cm)
VM Series - Blac 3½" (8.89 cm) - 4½" (11.43 cm)
FST02 - Black 4½" (11.43 cm)
ST02NT - Black ST02WC - Black & Chrome 5" (12.7 cm)
SLE50NT - Black SLE50WC - Black & Chrome 5" (12.7 cm)
TRG02 - Black Tail Gate Guard and Rail Protector
STB500 - Black 5" (12.7 cm)
RT - Series High Gloss Colors: 02, 04, 14, 47, 80, 84 7" (17.78 cm)
W4002 - Black W4014 - Silver N4002 - Black N4014 - Silver
BV01 - Chrome & Black
R102 - Black & Chrome
201 - Chrome & Black 202 - Black
92WC - Chrome & Black 92NT - Black
M301 - Chrome M302 - Black
301 - Chrome 302 - Black
0301 - Chrome 0302 - Black Colors Available
WLS01 -Chrome & Black WLS02 -Black
901 - Chrome 902 - Black
N91 - Chrome N92 - Black
WW2WC - Chrome & Black WW2NT - Black
B-D Company Section 5 - Page 23 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Trim Gard Special Order Moldings
WRT02 - Black WRT44 - Shell White DR02 - Black
RRT02 - Black
RRT32 - Black
NE01 - Chrome NE02 - Black Colors Available
PTC01 - Chrome (PT Cruiser Molding
WXL01 - Chrome & Black WXL02 - Black
3502E - Black (Embossed) 3502S - Black (Smooth) CT03 - Black & Chrome
B-D Company Section 5 - Page 24 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Rivet On Molding
Rivet-On Molding Rail 7½ ft Lengths
Rivet-On Molding Insert Sold by the Foot Available in Black or White
*Can be dyed*
Rivet-On Molding "Stub" Tips Available in Black or Gold
*Chrome Stub Tips are not available at this time*
Rivet-On Molding "Point" Tips Available in Gold *Chrome Point Tips are not available
at this time*
Rivet-On Molding "Bevel" Tips *Not available at this time*
Rivet-On Molding "Long" Tips Available in Chrome, Gold & Black
Rivet-On Molding Plastic Tips "Stub" is available in Chrome or Black "Bevel" is available in Chrome
B-D Company Section 5 - Page 25 303.744.1405 www-b-dco.com 1.800.748.2244
Body Side Molding - Body Side Molding Tools
The Multi-Cut has a mechanical action
different from that of scissors. With scissors
you're limited to cutting sheets of material,
such as paper, fabric and thin plastic. The
Multi-Cut has a mechanical action of a blade
coming down onto a flat anvil. This design
combined with a razor sharp blade & an offset
pivot point gives you incredible cutting ability
for cutting thick & rigid materials that have
density
PART # SOLD
AP16 16oz
Pro Bond Adhesive Promoter
PART # SOLD
MC10XP Kit
Replacement Anvil and Blades
PART #
MC10X
Replacement Anvil and Blades
PART # SOLD
6396 2.5cc Packets
3M® Adhesive Promoter