server connection- (fibre channel) - fujitsu
TRANSCRIPT
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
1/58
FUJITSU Storage
ETERNUS DXConfiguration Guide -Server Connection-
(Fibre Channel) for WindowsDriver Settings for Fujitsu Fibre Channel Cards
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
2/58
This page is intentionally left blank.
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
3/58
Preface
This manual briefly explains the operations that need to be performed by the user in order to connect an
ETERNUS DX Disk storage system or an ETERNUS DX200F All Flash Array to a Fujitsu server running Windows
via a Fibre Channel interface.
This manual is used when performing the setup procedure described in "Installing Drivers and Setting Up theServer" of the "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Win-
dows".
This manual should be used in conjunction with any other applicable user manuals, such as those for theETERNUS DX Disk storage system, ETERNUS DX200F All Flash Array, server, OS, Fibre Channel cards, and driv-ers.
Refer to "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- Notations" for the notationsused in this manual such as product trademarks and product names.
This manual references the following documents:
Server Support Matrix FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS DX60 S3/
DX100 S3/DX200 S3, ETERNUS DX500 S3/DX600 S3 Disk Storage Systems, ETERNUS DX200F All Flash ArraySettings
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS DX80 S2/DX90 S2, ETERNUS DX410 S2/DX440 S2, ETERNUS DX8100 S2/DX8700 S2 Disk Storage System Settings
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS DX60/DX60S2, DX80, DX90 Disk Storage System Settings
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS DX400/DX8000 series Disk Storage System Settings
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
This manual is designed for use with the following storage systems:
ETERNUS DX60 S3/DX100 S3/DX200 S3 Disk storage system
ETERNUS DX500 S3/DX600 S3 Disk storage system
ETERNUS DX60 S2/DX80 S2/DX90 S2 Disk storage system
ETERNUS DX410 S2/DX440 S2 Disk storage system
ETERNUS DX8100 S2/DX8700 S2 Disk storage system
ETERNUS DX60/DX80/DX90 Disk storage system
ETERNUS DX410/DX440 Disk storage system
ETERNUS DX8100/DX8400/DX8700 Disk storage system
ETERNUS DX200F All Flash Array
11th Edition
December 2014
3FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
4/58
The Contents and Structure of this Manual
This manual is composed of the following three chapters and an appendix.
"Chapter 1 Setup Procedure for PRIMERGY" (page 8)This chapter describes how to install a Fibre Channel card, set up the Fibre Channel card BIOS, install theFibre Channel card driver, check the driver version, and set up the driver parameters for PRIMERGY.
"Chapter 2 Setup Procedure for PRIMEQUEST 1000 Series" (page 30)
This chapter describes how to install a Fibre Channel card, set up the Fibre Channel card BIOS, install theFibre Channel card driver, check the driver version, and set up the driver parameters for PRIMEQUEST 1000series.
"Chapter 3 Setup Procedure for PRIMEQUEST 500/400 Series" (page 39)
This chapter describes how to install a Fibre Channel card, set up the Fibre Channel card BIOS, install theFibre Channel card driver, check the driver version, and set up the driver parameters for PRIMEQUEST500/400 series.
The appendix consists of a management table that is used in the "Setting Up the Fibre Channel Cards" sec-tion, and information on how to set up the server when Fujitsu QLogic Fibre Channel cards (2Gbit/s) are used.
Fibre Channel card names
Refer to "Server Support Matrix" to check the Fibre Channel cards.
"Fujitsu Emulex Fibre Channel cards" refers to Fibre Channel cards with the following product IDs.
- PG-FC105
- PG-FC106
- PG-FC107
- PG-FC201
- PG-FC202/PG-FC202L
- PG-FC203/PG-FC203L
- PY-FC201/PY-FC201L
- PG-FC204/PG-FC204L
- PY-FC202/PY-FC202L
- PY-FC221/PY-FC222
- PG-FCD201
- PG-FCD202
- MC-0JFC31/MCX0JFC31/MC-0JFC3L
- MC-0JFC91/MCX0JFC91/MC-0JFC9L
- MC-0JFC41/MCX0JFC41/MC-0JFC4L
- MC-0JFCA1/MCX0JFCA1/MC-0JFCAL
- MC-0JFC71/MCX0JFC71
- MC-0JFC72/MCX0JFC72/MC-0JFC7L
- MC-0JFC81/MCX0JFC81
- MC-0JFC82/MCX0JFC82/MC-0JFC8L
- MC-0JFC11/MC-0JFC1L
Preface
4FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
5/58
- MC-0JFC21/MC-0JFC2L
- MC-08FC11/MC-08FC71
- MC-08FC31/MC-08FC41
- MC-08FC51/MC-08FC61
- MC-08FC81/MC-08FC91- S26361-F2624-E1
- S26361-F2843-E1/S26361-F2843-E201
- S26361-F3141-E10/S26361-F3141-E210
- S26361-F3141-E1
- S26361-F3306-L1/S26361-F3306-L201
- S26361-F3961-L1/S26361-F3961-L201
- S26361-F3961-L2/S26361-F3961-L202
- S26361-F3306-E601/BX600-FC42E
- MC-FC82E "Fujitsu QLogic Fibre Channel cards" refers to Fibre Channel cards with the following product IDs.
- PG-FCD101
- PG-FCD102
- PG-FC205/PG-FC205L
- PY-FC211/PY-FC211L
- PG-FC206/PG-FC206L
- PY-FC212/PY-FC212L
- S26361-F3023-E1
-
S26361-F3631-L1/S26361-F3631-L201- S26361-F3631-L2/S26361-F3631-L202
Preface
5FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
6/58
Table of Contents
Chapter 1 Setup Procedure for PRIMERGY 8
1.1 Workflow ........................................................................................................................................ 8
1.2 For Fujitsu Emulex Fibre Channel Cards........................................................................................ 11
1.2.1 Setting Up the Fibre Channel Cards.....................................................................................................................11
1.2.2 Setting Up SAN Boot ...........................................................................................................................................14
1.2.3 Installing Windows .............................................................................................................................................14
1.2.4 Installing the Driver............................................................................................................................................14
1.2.5 Checking the Driver Version................................................................................................................................15
1.2.6 Setting Up the Driver Parameters .......................................................................................................................151.2.7 Setting Fixed Target IDs ......................................................................................................................................20
1.2.8 Installing the ETERNUS DX Driver........................................................................................................................20
1.3 For Fujitsu QLogic Fibre Channel Cards......................................................................................... 20
1.3.1 Setting Up the Fibre Channel Cards.....................................................................................................................20
1.3.2 Setting Up SAN Boot ...........................................................................................................................................23
1.3.3 Installing Windows .............................................................................................................................................25
1.3.4 Installing the Driver............................................................................................................................................25
1.3.5 Checking the Driver Version................................................................................................................................25
1.3.6 Setting Up the Driver Parameters .......................................................................................................................25
1.3.7 Installing the ETERNUS DX Driver........................................................................................................................28
Chapter 2 Setup Procedure for PRIMEQUEST 1000 Series 30
2.1 Workflow ...................................................................................................................................... 30
2.2 Setup Procedure for Fujitsu Emulex Fibre Channel Cards.............................................................. 32
2.2.1 Setting Up the Fibre Channel Cards.....................................................................................................................32
2.2.2 Installing the Driver............................................................................................................................................352.2.3 Checking the Driver Version................................................................................................................................35
2.2.4 Setting Up the Driver Parameters .......................................................................................................................36
2.2.5 Setting Fixed Target IDs ......................................................................................................................................37
2.2.6 Installing the ETERNUS DX Driver........................................................................................................................38
Chapter 3 Setup Procedure for PRIMEQUEST 500/400 Series 39
3.1 Workflow ...................................................................................................................................... 39
3.2 For Fujitsu Emulex Fibre Channel Cards........................................................................................ 40
6FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
7/58
3.2.1 Setting Up the Fibre Channel Cards.....................................................................................................................40
3.2.2 Installing the Driver............................................................................................................................................42
3.2.3 Checking the Driver Version................................................................................................................................43
3.2.4 Setting Up the Driver Parameters .......................................................................................................................43
3.2.5 Installing the ETERNUS DX Driver........................................................................................................................46
Appendix A WWN Instance Management Table for the Server (Blank) 47
Appendix B For Fujitsu QLogic Fibre Channel Cards (2Gbit/s) 48
B.1 Workflow...................................................................................................................................... 48
B.2 Setting Up the Fibre Channel Cards.............................................................................................. 50
B.3 Setting Up SAN Boot..................................................................................................................... 53B.4 Installing Windows....................................................................................................................... 55
B.5 Installing the Driver ..................................................................................................................... 55
B.6 Checking the Driver Version ......................................................................................................... 55
B.7 Installing the ETERNUS DX Driver ................................................................................................. 56
Table of Contents
7FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
8/58
Chapter 1Setup Procedure for PRIMERGY
This chapter describes how to install and set up the Fibre Channel cards in PRIMERGY.
1.1 Workflow
Workflow
When using the 2Gbit/s Fujitsu QLogic Fibre Channel cards, refer to "Appendix B For Fujitsu QLogic FibreChannel Cards (2Gbit/s)" (page 48).
Setting Up the Fibre Channel Cards
Install the Fibre Channel cards, acquire their physical addresses, and perform the BIOS settings.
For Fujitsu Emulex Fibre Channel cards
- "1.2.1 Setting Up the Fibre Channel Cards" (page 11)
For Fujitsu QLogic Fibre Channel Cards
- "1.3.1 Setting Up the Fibre Channel Cards" (page 20)
Setting Up SAN Boot
Set up the SAN Boot configuration (if SAN Boot is to be used).
For Fujitsu Emulex Fibre Channel cards
- "1.2.2 Setting Up SAN Boot" (page 14)
For Fujitsu QLogic Fibre Channel cards
- "1.3.2 Setting Up SAN Boot" (page 23)
8FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
9/58
Installing Windows
Install Windows.
For Fujitsu Emulex Fibre Channel cards
- "1.2.3 Installing Windows" (page 14) For Fujitsu QLogic Fibre Channel Cards
- "1.3.3 Installing Windows" (page 25)
Installing the Driver
Install the Fibre Channel card driver.
For Fujitsu Emulex Fibre Channel cards
- "1.2.4 Installing the Driver" (page 14)
- "1.2.5 Checking the Driver Version" (page 15)
For Fujitsu QLogic Fibre Channel cards
- "1.3.4 Installing the Driver" (page 25)
- "1.3.5 Checking the Driver Version" (page 25)
Setting Up the Driver ParametersSet up the parameters for the Fibre Channel card driver.
For Fujitsu Emulex Fibre Channel cards
- "1.2.6 Setting Up the Driver Parameters" (page 15)
For Fujitsu QLogic Fibre Channel cards
- "1.3.6 Setting Up the Driver Parameters" (page 25)
Chapter 1 Setup Procedure for PRIMERGY1.1 Workflow
9FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
10/58
Installing the ETERNUS DX Driver
Install the ETERNUS DX driver.
For Fujitsu Emulex Fibre Channel cards
- "1.2.8 Installing the ETERNUS DX Driver" (page 20)- Checking the driver-related notes
"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Win-
dows"
For Fujitsu QLogic Fibre Channel cards
- "1.3.7 Installing the ETERNUS DX Driver" (page 28)
- Checking the driver-related notes
"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Win-
dows"
After all of the required procedures in this manual are complete, proceed to the procedure that is de-scribed in "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for
Windows".
Chapter 1 Setup Procedure for PRIMERGY1.1 Workflow
10FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
11/58
1.2 For Fujitsu Emulex Fibre Channel Cards
This section describes how to set up the server for use with the Fujitsu Emulex Fibre Channel cards.
When using the Fujitsu QLogic Fibre Channel cards, follow the procedure in "1.3 For Fujitsu QLogic FibreChannel Cards" (page 20).
Depending on the Fibre Channel card used, the actual on-screen Fibre Channel card information may dif-fer from that in the screenshots shown in this manual.
1.2.1 Setting Up the Fibre Channel Cards
Install the Fibre Channel cards in the server, acquire the relevant physical addresses and World Wide Names
(WWNs), and perform Topology and LinkSpeed settings. The physical address and WWN of a Fibre Channel card are required information in the following cases:
when an error has occurred in the system, when using the ETERNUS DX storage systems (security function,host affinity function, etc.) to restrict server access, or when connecting the ETERNUS DX storage systemsand the server using a Fibre Channel switch.
The relationship between a physical address and WWN cannot be determined from BIOS and OS. The physi-cal address and WWN must be recorded as a pair when each Fibre Channel card is installed. Physical ad-dress and WWN must be assigned to "WWN instance management table for the server".
The workflow is shown below.
(1) Install the Fibre Channel card
(2) Turn on the server
(3) Acquire the physical address and WWN for the Fibre Channel card
(4) Add a record for the server in the WWN instance management table for the server
(5) Set the Topology and LinkSpeedWhen installing two or more Fibre Channel cards in the server, first turn off the server, then repeat Steps (1)through (5) above for each Fibre Channel card to be installed.
The procedure is as follows:
1 Install the Fibre Channel card in the server.
For the installation method, slot positions, and notes regarding the Fibre Channel card, refer to themanual provided with the Fibre Channel card or the user guide of the server.
2 Turn on the server, and press the [Alt] + [E] keys or [Ctrl] + [E] keys while the following message isdisplayed.
!!! Emulex LightPulse x86 BIOS !!!, Version xxxxxx
Copyright (c)1997-2010 Emulex.All rights reserved.
Press or to enter Emulex BIOS configuration
utility. Press to skip Emulex BIOS.
"LightPulse BIOS Utility" starts.
Chapter 1 Setup Procedure for PRIMERGY1.2 For Fujitsu Emulex Fibre Channel Cards
11FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
12/58
3 Select the port for the Fibre Channel card that is to be checked and press the [Enter] key.
4 Check the [Mem Base] and [Port Name] values.
The value of [Mem Base] is the physical address and the value of [Port Name] is the WWN.
Physical address
Fibre Channel card WWN
-------------------------------------------------------------------------------
Emulex LightPulse FC BIOS Utility, KA6.00a13
-------------------------------------------------------------------------------
01: LPe16002-M6: Bus#: 02 Dev#: 00 Func#: 00
Mem Base: CE000000 Firmware Version: 1.1.8.0 BIOS: Disabled
Port Name: 10000090FA02097E Node Name: 20000090FA02097E
Link Status: Link Down
-------------------------------------------------------------------------------
Enable/Disable Boot from SAN
Scan for Target Devices
Reset Adapter Defaults
Configure Boot Devices
Configure Advanced Adapter Parameters
Enter to Previous Menu
< / > to Highlight, to Select
The name of the physical address might be "I/O Base", " I/O Address", or "Mem Base", depending onthe HBA BIOS version. For more information about how to check the physical address, refer to the
HBA manual.
5 Record the physical address and WWN in the "WWN instance management table for the server".
(found in "Appendix A WWN Instance Management Table for the Server (Blank)" (page 47)).
The following shows an example of this.
WWN instance management table for the server
Host name
IP Address
Physical slot
nameFibre Channel card WWN Instance name Physical address Cable tag
slot0 10000090FA02097E CE000000
Details of contents
The details of contents for the WWN instance management table for the server are as follows:
Host name:
Record the host name.
Chapter 1 Setup Procedure for PRIMERGY1.2 For Fujitsu Emulex Fibre Channel Cards
12FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
13/58
IP Address:
Record the IP address of the server.
Physical slot name:
Record the slot position of the installed Fibre Channel card.
For the installation location, refer to the User's Guide for each server.
Fibre Channel card WWN:
Record the value of [Port Name] or [Adapter Port Name].
Instance name:
Not necessary to record.
Physical address:
Record the value of [I/O Base], [I/O Address], or [Mem Base].
Cable tag:
Record a tag name which indicates the connection path (relationship between the connected deviceand the port).
6 Select "Configure Advanced Adapter Parameters" and press the [Enter] key.
7 Select "Topology Selection" and press the [Enter] key.
8 Select "Auto Topology: Loop first (Default)" (for a direct connection) or "Fabric Point to Point" (for aswitch connection), and then press the [Enter] key.
When a direct connection is used and the LinkSpeed is 16Gbit/s, select "Fabric Point to Point".
9 Press the [Esc] key to return to the window shown in Step 7.
10 Select "Link Speed Selection" and press the [Enter] key.
11 Select the transfer rate according to the values listed in the LinkSpeed settings table below, and pressthe [Enter] key.
LinkSpeed settings
FibreChannelcard trans-fer rate
Switch connection
Fibre Channel switch transfer rate
Direct connection
CA transfer rate
16Gbit/s 8Gbit/s 4Gbit/s 2Gbit/s 1Gbit/s 16Gbit/s 8Gbit/s 4Gbit/s
16Gbit/s 16 8 4 16 8 4
8Gbit/s 8 8 4 2 8 8 4
4Gbit/s 4 4 4 2 1 4 4 4
2Gbit/s 2 2 2 1 2 2
12 Press the [Esc] key to quit the "Emulex LightPulse FC BIOS Utility".
When the total number of ports for installed Fibre Channel cards is two or more, first repeat Step 3through Step 11for each port, and then press the [Esc] key to exit "Emulex LightPulse FC BIOS Utility".
Chapter 1 Setup Procedure for PRIMERGY1.2 For Fujitsu Emulex Fibre Channel Cards
13FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
14/58
If two or more Fibre Channel cards have already been installed in the server at the time of purchase,the one-to-one relationship between the WWNs and Fibre Channel cards may not be easy to deter-mine. The WWNs that are obtained in this section may need to be repeatedly registered and set up
on the ETERNUS DX until a server recognizes the ETERNUS DX logical disks.For details about ETERNUS DX settings, refer to the following manuals.
"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUSDX60 S3/DX100 S3/DX200 S3, ETERNUS DX500 S3/DX600 S3 Disk Storage Systems, ETERNUSDX200F All Flash Array Settings"
"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUSDX80 S2/DX90 S2, ETERNUS DX410 S2/DX440 S2, ETERNUS DX8100 S2/DX8700 S2 Disk Storage Sys-tem Settings"
"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUSDX60/DX60 S2, DX80, DX90 Disk Storage System Settings"
"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS
DX400/DX8000 series Disk Storage System Settings"
1.2.2 Setting Up SAN Boot
Refer to "Server Support Matrix" to check the support status of SAN Boot and refer to the manual of the serv-er, OS, or the Fibre Channel card that is to be used.
When using a logical unit (LUN) of the ETERNUS DX storage systems as a boot disk, make sure that the LUNhas enough capacity to install the OS.
1.2.3 Installing Windows
Refer to the documentation supplied with the product for Windows installation details.
1.2.4 Installing the Driver
Refer to the documentation provided with each Fibre Channel card for details on how to obtain and install aFibre Channel card driver for it.
Chapter 1 Setup Procedure for PRIMERGY1.2 For Fujitsu Emulex Fibre Channel Cards
14FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
15/58
1.2.5 Checking the Driver Version
Use the Device Manager to check the version of the Fibre Channel card driver.
1 In the Device Manager, go to [Storage controllers], and open the [Properties] of the Fibre Channel card.
2 Select the [Driver] tab, and open [Driver Details].
3 Select the driver file, and check its [File version].
If a different driver version is displayed from that shown in "Server Support Matrix", reinstall the driv-er.
1.2.6 Setting Up the Driver Parameters
The procedure depends on the type of Fibre Channel card that is being used.
For the 2Gbit/s Fibre Channel cards, proceed to "1.2.6.1 For 2Gbit/s Fibre Channel Cards" (page 15).
For 16Gbit/s Fibre Channel cards, 8Gbit/s Fibre Channel cards, or 4Gbit/s Fibre Channel cards, proceed to"1.2.6.2 For 16Gbit/s, 8Gbit/s, and 4Gbit/s Fibre Channel Cards" (page 17).
1.2.6.1 For 2Gbit/s Fibre Channel Cards
Set the driver parameters after installing HBAnyware.
1 Install HBAnyware.
For installation, refer to the Fibre Channel card manual.
The Driver Parameter Setting Tool (LightPulse Utility/NT) is included in HBAnyware.
2 Start up the "LightPulse Utility/NT".
3 Select [Driver Parameters] from [Category:].
4 Select [Registry] with the radio button.
The registry contents are displayed.
Chapter 1 Setup Procedure for PRIMERGY1.2 For Fujitsu Emulex Fibre Channel Cards
15FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
16/58
The display contents vary according to the installed Fibre Channel card type and the driver version.
5 Double click [Device].The [Modify Registry Entry] dialog box is displayed.
6 Check the current values of each parameter.
Compare with the parameter values in the tables below, and correct the current value if necessary.
If the parameter is not shown, add the necessary information.
For Windows Server2003
Fibre Channel cardtransfer rate
Setting value
Topology QueueDepth Queue Target LinkSpeed
2Gbit/s 0 (direct connection)
1 (switch connection)
Arbitrary (*1)
(Up to 512 for eachFC port of the ETER-NUS DX)
0 2 (direct connection)
2 (8Gbit/s switch con-nection)
2 (4Gbit/s switch con-nection)
2 (2Gbit/s switch con-nection)
1 (1Gbit/s switch con-nection)
*1: Recommended value = 512 (number of Fibre Channel ports that are connected to a single CAport) number of LUNs
(Round the result down)
Use the value of "8" if the actual result is lower.
If correcting or adding parameters, note the following restrictions.
Describe each parameter, using ";" (semicolon) to delimit.
Enter each parameter, using correct spelling. Note that misspelled words are not checked.
Do not modify any parameters other than those described here.
The following describes each parameter: "Topology" parameter
Set the connection configuration between the server and ETERNUS DX storage systems.
"QueueDepth" parameter
Set the command queue depth.
"QueueTarget" parameter
Set to specify the command queue depth to either the LUN or to the target.
"LinkSpeed" parameter
Set the link speed.
Chapter 1 Setup Procedure for PRIMERGY1.2 For Fujitsu Emulex Fibre Channel Cards
16FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
17/58
7 After all the cards have been set, select [Exit] from the [File] menu to quit the "LightPulse Utility/NT".
1.2.6.2 For 16Gbit/s, 8Gbit/s, and 4Gbit/s Fibre Channel CardsSet the driver parameters after installing OneCommand Manager.
When the server OS is Windows Server2012 R2, Windows Server2012, Windows Server2008 R2, Windows
Server2008, or Windows Server2003, it is recommended that fixed Target IDs be assigned to the FibreChannel card connected devices, and that automatic Target ID allocation be disabled.
For details of the Target ID settings, refer to the "Fibre Channel Controller User's Guide".
By default, Target IDs are automatically allocated. However, when a device is added, automatic Target IDallocation can result in a different distribution of Target IDs, which can cause the devices to not be recog-
nized.
1 Install OneCommand Manager.
For installation, refer to the Fibre Channel card manual.
2 Start OneCommand Manager.
3 Select the target Fibre Channel card port and click the [Driver Parameters] tab.
Chapter 1 Setup Procedure for PRIMERGY1.2 For Fujitsu Emulex Fibre Channel Cards
17FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
18/58
4 Check the parameter values in the [Adapter Parameter] list.
Compare with the parameter values in the following tables, and correct the current value if necessary.
Select the parameter whose value is to be corrected from the [Adapter Parameter] list and modify thevalue in the [Modify Adapter Parameter] area.
For Windows Server2012 R2, Windows Server2012, or Windows Server2008 R2
Fibre Channel cardtransfer rate
Setting value
Topology QueueDepth Queue Target LinkSpeed
16Gbit/s
8Gbit/s
4Gbit/s
0 (direct connection)
1 (switch connection)
When a direct con-nection is used andthe LinkSpeed is16Gbit/s, select "1".
Arbitrary (*1)
(Up to 512 for each
FC port of the ETER-NUS DX)
0 (*2)
*1: Recommended value = 512 (number of Fibre Channel ports that are connected to a single CAport) number of LUNs
(Round the result down)
Use the value of "8" if the actual result is lower.
*2: LinkSpeed setting value list:
FibreChannelcardtransferrate
Switch connection
Fibre Channel switch transfer rate
Direct connection
CA transfer rate
16Gbit/s 8Gbit/s 4Gbit/s 2Gbit/s 1Gbit/s 16Gbit/s 8Gbit/s 4Gbit/s
16Gbit/s 16 8 4 16 8 4
8Gbit/s 8 8 4 2 8 8 4
4Gbit/s 4 4 4 2 1 4 4 4
Chapter 1 Setup Procedure for PRIMERGY1.2 For Fujitsu Emulex Fibre Channel Cards
18FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
19/58
For Windows Server2008 or Windows Server2003
Fibre Channel cardtransfer rate
Setting value
Topology QueueDepth Queue Target LinkSpeed
8Gbit/s
4Gbit/s
0 (direct connection)
1 (switch connection)
Arbitrary (*1)
(Up to 512 for eachFC port of the ETER-NUS DX)
0 (*2)
*1: Recommended value = 512 (number of Fibre Channel ports that are connected to a single CAport) number of LUNs
(Round the result down)
Use the value of "8" if the actual result is lower.
*2: LinkSpeed setting value list:
Fibre
Channelcardtransferrate
Switch connection
Fibre Channel switch transfer rate
Direct connection
CA transfer rate
16Gbit/s 8Gbit/s 4Gbit/s 2Gbit/s 1Gbit/s 16Gbit/s 8Gbit/s 4Gbit/s
8Gbit/s 8 8 4 2 8 8 4
4Gbit/s 4 4 4 2 1 4 4 4
Do not modify any parameters other than those described here.
The following describes each parameter:
"Topology" parameter
Set the connection configuration between the server and ETERNUS DX storage systems.
"QueueDepth" parameter
Set the command queue depth.
"QueueTarget" parameter
Set to specify the command queue depth to either the LUN or to the target.
"LinkSpeed" parameter
Set the link speed.
5 After the values have been modified, click the [Apply] button.Parameters that are displayed in red in the [Adapter Parameter] column show that their values havebeen modified but not yet applied. Click the [Apply] button to apply the changed values.
6 If there are multiple cards, repeat Step 2through Step 5to change the settings for all cards.
7 After all the cards have been set, select [Exit] from the [File] menu to quit OneCommand Manager.
Chapter 1 Setup Procedure for PRIMERGY1.2 For Fujitsu Emulex Fibre Channel Cards
19FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
20/58
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
21/58
The workflow is shown below.
(1) Install the Fibre Channel card
(2) Turn on the server
(3) Acquire the physical address and WWN for the Fibre Channel card
(4) Add a record for the server in the WWN instance management table for the server(5) Set the Fibre Channel card BIOS
When installing two or more Fibre Channel cards in the server, first turn off the server, then repeat Steps (1)through (5) above for each Fibre Channel card to be installed.
The procedure is as follows:
1 Install the Fibre Channel card in the server.
For the installation method, position (PCI bus slots), and notes regarding the Fibre Channel card, referto the Fibre Channel card manual or the user guide of the server.
2 Turn on the server, and press the [Ctrl] + [Q] keys while the following message is displayed.
QLogic Corporation
QLA23xx PCI Fibre Channel ROM BIOS Version *.**
Copyright(C) QLogic Corporation 2000. All rights reserved
www.qlogic.com
Press for Fast!UTIL
The "Fast!UTIL" program starts up (Startup may take longer than usual).
3 Check the value of [I/O Address] of the [Select Host Adapter] window.
The value of [I/O Address] is the physical address.
Adapter Type
QLA2xxx
I/O Address
3400
Select Host Adapter
Physical
address
4 Select [Configuration Settings] from the [Fast!UTIL Options] menu and press the [Enter] key.
5 Select [Host Adapter Settings] from the [Configuration Settings] menu and press the [Enter] key.
6 Check the value of [Adapter Port Name].
The value of [Adapter Port Name] is the Fibre Channel card WWN.Host Adapter Settings
BIOS Address
BIOS Revision
Adapter Serial Number
Interrupt Level
Adapter Port Name
Host Adapter BIOS
:xxxxx
:x.xx
:xxxxxx
:xx
:200000E08B0214D0
:Disabled
7 Record the physical address and WWN in the "WWN instance management table for the server".
(found in "Appendix A WWN Instance Management Table for the Server (Blank)" (page 47)).
Chapter 1 Setup Procedure for PRIMERGY1.3 For Fujitsu QLogic Fibre Channel Cards
21FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
22/58
The following shows an example of this.
Host name Server#1
IP Address 192.168.0.10
Physical slot
nameFibre Channel card WWN Instance name Physical address Cable tag
slot0 20 00 00 E0 8B 02 14 D0 3400 SERV1_SLOT0 to SN200_1_port0
8 Set up the BIOS parameters for the Fibre Channel card.
Check the values for each parameter in the [Host Adapter Settings] window. See the following tablesand set each value. For details on how to set the values, refer to the BIOS Readme file and Fibre Chan-nel card user's guide.
Parameter Host Adapter settings value Remarks
BIOS Address Fixed for each card Settings cannot be changed.
BIOS Revision (*1)
Adapter Serial Number
Interrupt Level
Adapter Port Name
Host Adapter BIOS Enabled or Disabled Set "Enabled" for SAN Boot.
Set "Disabled" for non SAN Boot.
Frame Size 2048 If the current parameter values are dif-ferent, change them to the indicated
values.Loop Reset Delay 5Adapter Hard Loop ID Disabled
Hard Loop ID 0
Spinup Delay Disabled
Connection Options 0 or 1 For direct connection: 0 (*2)
For switch connection: 1 (*3)
Fibre Channel
Tape Support
Disabled If "Enabled" is displayed, change thevalue to "Disabled".
Data Rate (*4) 1: 2Gbit/s fixed
2: Auto-negotiated
3: 4Gbit/s fixed
4: 8Gbit/s fixed
5: 16Gbit/s fixed
*1: The BIOS version of the Fibre Channel card is displayed. Check that the BIOS version is the same asshown in "Server Support Matrix".
*2: When connecting directly to the ETERNUS DX storage systems via a Fibre Channel pass-throughblade
However, select "1" for direct connections with 16Gbit/s Fibre Channel cards.
*3: When the Fibre Channel switch is connected to the ETERNUS DX storage systems via a Fibre Chan-nel pass-through blade or Fibre Channel switch blade.
Chapter 1 Setup Procedure for PRIMERGY1.3 For Fujitsu QLogic Fibre Channel Cards
22FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
23/58
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
24/58
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
25/58
7 Select [Exit Fast!UTIL] and press the [Enter] key.
8 Select [Reboot System] and press the [Enter] key.
Reboot System
Return to Fast!UTIL
Exit Fast!UTIL
The server reboots.
To return to the [Fast!UTIL] menu, select [Return to Fast!UTIL].
1.3.3 Installing WindowsRefer to the documentation supplied with the product for Windows installation details.
1.3.4 Installing the Driver
Refer to the documentation provided with each Fibre Channel card for details on how to obtain and install aFibre Channel card driver for it.
1.3.5 Checking the Driver Version
Use the Device Manager to check the version of the Fibre Channel card driver.
1 In the Device Manager, go to [Storage controllers], and open the [Properties] of the Fibre Channel card.
2 Select the [Driver] tab, and open [Driver Details].
3 Select the driver file, and check its [File version].
If a different driver version is displayed from that shown in "Server Support Matrix", reinstall the driv-er.
1.3.6 Setting Up the Driver Parameters
Set the driver parameters using the following procedure.
Chapter 1 Setup Procedure for PRIMERGY1.3 For Fujitsu QLogic Fibre Channel Cards
25FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
26/58
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
27/58
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
28/58
(3) Move to the path as shown below:
HKEY_LOCAL_MACHINE
\SYSTEM
\CurrentControlSet
\Services \ql2300 \Parameters
\Device
(4) Double click [DriverParameter].
(5) Enter the Queue Depth value (qd="recommended value") in "Value data" and click the [OK] but-ton.
Recommended value = 512 (number of Fibre Channel ports that are connected to a single CAport) number of LUNs
(Round the result down)
Use the value of "8" if the actual result is lower.
Use the value of "254" if the actual result is higher.
(6) Close the Registry Editor.
9 Reboot the server.
1.3.7 Installing the ETERNUS DX Driver
Install the driver for ETERNUS DX storage systems as required.
Refer to the "Driver Notes" section in "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-
(Fibre Channel) for Windows" for notes on each driver in cases such as when connecting the server to theETERNUS DX in multipath configuration and using the path redundancy control (path fail-over) function,
and for when single-path connection is used between the ETERNUS DX and server.
Chapter 1 Setup Procedure for PRIMERGY1.3 For Fujitsu QLogic Fibre Channel Cards
28FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
29/58
For the procedure about how to install (or uninstall), set up, and use the drivers for ETERNUS DX storagesystems, refer to the software manuals.
Chapter 1 Setup Procedure for PRIMERGY1.3 For Fujitsu QLogic Fibre Channel Cards
29FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
30/58
Chapter 2Setup Procedure for PRIMEQUEST 1000 Series
This chapter describes how to install and set up the Fibre Channel cards in the PRIMEQUEST 1000 series.
2.1 Workflow
Workflow
Installing the Fibre Channel Card
Install the Fibre Channel card and its driver, check the driver version, and set up the Fibre Channelcard BIOS.
For Fujitsu Emulex Fibre Channel cards
- "2.2.1 Setting Up the Fibre Channel Cards" (page 32)
- "2.2.2 Installing the Driver" (page 35)
Setting Up the Driver Parameters
Set the Topology, QueueDepth and other parameters.
For Fujitsu Emulex Fibre Channel Cards
- "2.2.4 Setting Up the Driver Parameters" (page 36)
30FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
31/58
Installing the ETERNUS DX Driver
Install the ETERNUS DX driver.
For Fujitsu Emulex Fibre Channel Cards
- "2.2.6 Installing the ETERNUS DX Driver" (page 38)- Checking the driver-related notes
"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Win-
dows"
After all of the required procedures in this manual are complete, proceed to the procedure that is de-scribed in "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for
Windows".
Chapter 2 Setup Procedure for PRIMEQUEST 1000 Series2.1 Workflow
31FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
32/58
2.2 Setup Procedure for Fujitsu Emulex Fibre Channel Cards
If a SAN boot environment is to be set up, the SAN boot settings must be made beforehand for the PRIME-QUEST 1000 series. Refer to "PRIMEQUEST 1000 Series SAN Boot Environment Configuration Manual" fordetails.
2.2.1 Setting Up the Fibre Channel Cards
Install the Fibre Channel cards in the server, acquire the relevant physical addresses and World Wide Names(WWNs), and perform Topology and LinkSpeed settings.
The physical address and WWN of a Fibre Channel card are required information in the following cases:when an error has occurred in the system, when using the ETERNUS DX storage systems (security function,
host affinity function, etc.) to restrict server access, or when connecting the ETERNUS DX storage systemsand the server using a Fibre Channel switch.
The relationship between a physical address and WWN cannot be determined from BIOS and OS. The physi-cal address and WWN must be recorded as a pair when each Fibre Channel card is installed. Physical ad-dress and WWN must be assigned to "WWN instance management table for the server".
The workflow is shown below.
(1) Install the Fibre Channel card
(2) Turn on the server
(3) Acquire the physical address and WWN for the Fibre Channel card
(4) Add a record for the server in the WWN instance management table for the server
(5) Set the Topology and LinkSpeedWhen installing two or more Fibre Channel cards in the server, first turn off the server, then repeat Steps (1)through (5) above for each Fibre Channel card to be installed.
The procedure is as follows:
1 Install the Fibre Channel card in the server.
For the installation method, slot positions, and notes regarding the Fibre Channel card, refer to themanual provided with the Fibre Channel card or the user guide of the server.
2 Turn on the server, and press the [Alt] + [E] keys or [Ctrl] + [E] keys while the following message isdisplayed.
!!! Emulex LightPulse x86 BIOS !!!, Version xxxxxx
Copyright (c)1997-2010 Emulex.All rights reserved.
Press or to enter Emulex BIOS configuration
utility. Press to skip Emulex BIOS.
"LightPulse BIOS Utility" starts.
3 Select the port for the Fibre Channel card that is to be checked and press the [Enter] key.
Chapter 2 Setup Procedure for PRIMEQUEST 1000 Series2.2 Setup Procedure for Fujitsu Emulex Fibre Channel Cards
32FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
33/58
4 Check the [Mem Base] and [Port Name] values.
The value of [Mem Base] is the physical address and the value of [Port Name] is the WWN.
Physical address
Fibre Channel card WWN
-------------------------------------------------------------------------------
Emulex LightPulse FC BIOS Utility, KA6.00a13
-------------------------------------------------------------------------------01: LPe16002-M6: Bus#: 02 Dev#: 00 Func#: 00
Mem Base: CE000000 Firmware Version: 1.1.8.0 BIOS: Disabled
Port Name: 10000090FA02097E Node Name: 20000090FA02097E
Link Status: Link Down
-------------------------------------------------------------------------------
Enable/Disable Boot from SAN
Scan for Target Devices
Reset Adapter Defaults
Configure Boot Devices
Configure Advanced Adapter Parameters
Enter to Previous Menu
< / > to Highlight, to Select
The name of the physical address might be "I/O Base", " I/O Address", or "Mem Base", depending onthe HBA BIOS version. For more information about how to check the physical address, refer to theHBA manual.
5 Record the physical address and WWN in the "WWN instance management table for the server".
(found in "Appendix A WWN Instance Management Table for the Server (Blank)" (page 47)).
The following shows an example of this.
WWN instance management table for the server
Host name
IP Address
Physical slotname
Fibre Channel card WWN Instance name Physical address Cable tag
slot0 10000090FA02097E CE000000
Details of contents
The details of contents for the WWN instance management table for the server are as follows:
Host name:
Record the host name.
IP Address:
Record the IP address of the server.
Chapter 2 Setup Procedure for PRIMEQUEST 1000 Series2.2 Setup Procedure for Fujitsu Emulex Fibre Channel Cards
33FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
34/58
Physical slot name:
Record the slot position of the installed Fibre Channel card.
For the installation location, refer to the User's Guide for each server.
Fibre Channel card WWN:
Record the value of [Port Name] or [Adapter Port Name].
Instance name:
Not necessary to record.
Physical address:
Record the value of [I/O Base], [I/O Address], or [Mem Base].
Cable tag:
Record a tag name which indicates the connection path (relationship between the connected deviceand the port).
6 Select "Configure Advanced Adapter Parameters" and press the [Enter] key.
7 Select "Topology Selection" and press the [Enter] key.
8 Select "Auto Topology: Loop first (Default)" (for a direct connection) or "Fabric Point to Point" (for aswitch connection), and then press the [Enter] key.
9 Press the [Esc] key to return to the window shown in Step 7.
10 Select "Link Speed Selection" and press the [Enter] key.
11 Select the transfer rate according to the values listed in the LinkSpeed settings table below, and pressthe [Enter] key.
LinkSpeed settings
FibreChannelcard trans-fer rate
Switch connection
Fibre Channel switch transfer rate
Direct connection
CA transfer rate
16Gbit/s 8Gbit/s 4Gbit/s 2Gbit/s 1Gbit/s 16Gbit/s 8Gbit/s 4Gbit/s
8Gbit/s 8 8 4 2 8 8 4
4Gbit/s 4 4 4 2 1 4 4 4
2Gbit/s 2 2 2 1 2 2
12 Press the [Esc] key to quit the "Emulex LightPulse FC BIOS Utility".
When the total number of ports for installed Fibre Channel cards is two or more, first repeat Step 3through Step 11for each port, and then press the [Esc] key to exit "Emulex LightPulse FC BIOS Utility".
Chapter 2 Setup Procedure for PRIMEQUEST 1000 Series2.2 Setup Procedure for Fujitsu Emulex Fibre Channel Cards
34FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
35/58
If two or more Fibre Channel cards have already been installed in the server at the time of purchase,the one-to-one relationship between the WWNs and Fibre Channel cards may not be easy to deter-mine. The WWNs that are obtained in this section may need to be repeatedly registered and set up
on the ETERNUS DX until a server recognizes the ETERNUS DX logical disks.For details about ETERNUS DX settings, refer to the following manuals.
"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUSDX60 S3/DX100 S3/DX200 S3, ETERNUS DX500 S3/DX600 S3 Disk Storage Systems, ETERNUSDX200F All Flash Array Settings"
"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUSDX80 S2/DX90 S2, ETERNUS DX410 S2/DX440 S2, ETERNUS DX8100 S2/DX8700 S2 Disk Storage Sys-tem Settings"
"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUSDX60/DX60 S2, DX80, DX90 Disk Storage System Settings"
"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS
DX400/DX8000 series Disk Storage System Settings"
2.2.2 Installing the Driver
Refer to the documentation provided with each Fibre Channel card for details on how to obtain and install aFibre Channel card driver for it.
2.2.3 Checking the Driver VersionUse the Device Manager to check the version of the Fibre Channel card driver.
1 In the Device Manager, go to [Storage Area controllers], and open the [Properties] of the Fibre Channelcard.
2 Select the [Driver] tab, and open [Driver Details].
3 Select the driver file, and check its [File version].
If a different driver version is displayed from that shown in "Server Support Matrix", reinstall the driv-er.
Chapter 2 Setup Procedure for PRIMEQUEST 1000 Series2.2 Setup Procedure for Fujitsu Emulex Fibre Channel Cards
35FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
36/58
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
37/58
*2: LinkSpeed setting value list:
Fibre Chan-nel cardtransferrate
Switch connection
Fibre Channel switch transfer rate
Direct connection
CA transfer rate
16Gbit/s 8Gbit/s 4Gbit/s 2Gbit/s 16Gbit/s 8Gbit/s 4Gbit/s
8Gbit/s 8 8 4 2 8 8 4
Do not modify any parameters other than those described here.
The following describes each parameter:
"Topology" parameter
Set the connection configuration between the server and ETERNUS DX storage systems.
"QueueDepth" parameter
Set the command queue depth.
"QueueTarget" parameter
Set to specify the command queue depth to either the LUN or to the target.
"LinkSpeed" parameter
Set the link speed.
5 After the values have been modified, click the [Apply] button.
Parameters that are displayed in red in the [Adapter Parameter] column show that their values havebeen modified but not yet applied. Click the [Apply] button to apply the changed values.
6 If there are multiple cards, repeat Step 2through Step 5to change the settings for all cards.
7 After all the cards have been set, select [Exit] from the [File] menu to quit OneCommand Manager.
2.2.5 Setting Fixed Target IDs
Each device connected to a Fibre Channel card is allocated a Target ID. By default, these Target IDs are auto-matically allocated by the driver. Under this default, the device Target IDs may be reallocated as devices areadded and removed, or depending on how the devices are recognized. If the Target IDs have changed when
the server reboots, devices may end up off-line, and unavailable depending on the OS or application beingused. To avoid this, it is recommended that a fixed Target ID be allocated to each device and automatic Tar-get ID allocation be disabled.
Contact your supplier for more details.
Chapter 2 Setup Procedure for PRIMEQUEST 1000 Series2.2 Setup Procedure for Fujitsu Emulex Fibre Channel Cards
37FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
38/58
2.2.6 Installing the ETERNUS DX Driver
Install the driver for ETERNUS DX storage systems as required.
Refer to the "Driver Notes" section in "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-
(Fibre Channel) for Windows" for notes on each driver in cases such as when connecting the server to the
ETERNUS DX in multipath configuration and using the path redundancy control (path fail-over) function,and for when single-path connection is used between the ETERNUS DX and server.
For the procedure about how to install (or uninstall), set up, and use the drivers for ETERNUS DX storagesystems, refer to the software manuals.
Chapter 2 Setup Procedure for PRIMEQUEST 1000 Series2.2 Setup Procedure for Fujitsu Emulex Fibre Channel Cards
38FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
39/58
Chapter 3Setup Procedure for PRIMEQUEST 500/400 Series
This chapter describes how to install and set up the Fibre Channel cards in the PRIMEQUEST 500/400 series.
3.1 Workflow
Workflow
Installing the Fibre Channel Card
Install the Fibre Channel card and acquire WWPN information.
For Fujitsu Emulex Fibre Channel cards
- "3.2.1 Setting Up the Fibre Channel Cards" (page 40)
- "Appendix A WWN Instance Management Table for the Server (Blank)" (page 47)
- Checking the WWPN acquisition procedure
"PRIMEQUEST 500A/500/400 SERIES INSTALLATION MANUAL"
Installing the Driver
Install the Fibre Channel card driver.
For Fujitsu Emulex Fibre Channel cards
- "3.2.2 Installing the Driver" (page 42)
- Checking how to obtain and install the Fibre Channel card driver
Fibre Channel card documentation
39FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
40/58
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
41/58
The workflow is shown below.
(1) Install the Fibre Channel card
(2) Turn on the server
(3) Acquire the physical address and WWPN for the Fibre Channel card
(4) Add a record for the server in the WWN instance management table for the server(5) Set the Topology and LinkSpeed
The following shows an example of this.
Host name
IP Address
Physical slot name Fibre Channel card WWN Instance name Physical address Cable tag
slot0 10 00 00 00 C9 38 D2 29 5000
Details of contents
The details of contents for the WWPN instance management table for the server are as follows:
Host name:
Record the host name.
IP Address:
Record the IP address of the server.
Physical slot name:
Record the slot position of the installed Fibre Channel card.
For the installation location, refer to the User's Guide for each server.
Fibre Channel card WWPN:
Record the WWPN of the Fibre Channel card.
Instance name:
Not necessary to record.
Physical address:
Record the value of [I/O Base] or [I/O Address].
Cable tag:
Record a tag name which indicates the connection path (relationship between the connected device andthe port).
Topology
Set the Topology according to the system configuration that is used:
For direct connections: "1. Auto Topology: Loop first (Default)"
For switch connections: "4. Fabric Point to Point"
Chapter 3 Setup Procedure for PRIMEQUEST 500/400 Series3.2 For Fujitsu Emulex Fibre Channel Cards
41FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
42/58
LinkSpeed
Set the link speed according to the values listed in the following table.
Fibre Chan-nel cardtransferrate
Switch connection
Fibre Channel switch transfer rate
Direct connection
CA transfer rate
16Gbit/s 8Gbit/s 4Gbit/s 2Gbit/s 1Gbit/s 16Gbit/s 8Gbit/s 4Gbit/s
8Gbit/s 8 8 4 2 8 8 4
4Gbit/s 4 4 4 2 1 4 4 4
2Gbit/s 2 2 2 1 2 2
When installing two or more Fibre Channel cards in the server, first turn off the server, then repeat Steps (1)through (5) above for each Fibre Channel card to be installed.
If two or more Fibre Channel cards have already been installed in the server at the time of purchase, theone-to-one relationship between the WWPNs and Fibre Channel cards may not be easy to determine. TheWWPNs that are obtained in this section may need to be repeatedly registered and set up on the ETERNUSDX until a server recognizes the ETERNUS DX logical disks.
For details about ETERNUS DX settings, refer to the following manuals.
"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS DX60S3/DX100 S3/DX200 S3, ETERNUS DX500 S3/DX600 S3 Disk Storage Systems, ETERNUS DX200F All FlashArray Settings"
"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS DX80S2/DX90 S2, ETERNUS DX410 S2/DX440 S2, ETERNUS DX8100 S2/DX8700 S2 Disk Storage System Set-tings"
"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS DX60/DX60 S2, DX80, DX90 Disk Storage System Settings"
"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) ETERNUS DX400/DX8000 series Disk Storage System Settings"
3.2.2 Installing the Driver
Refer to the documentation provided with each Fibre Channel card for details on how to obtain and install aFibre Channel card driver for it.
Chapter 3 Setup Procedure for PRIMEQUEST 500/400 Series3.2 For Fujitsu Emulex Fibre Channel Cards
42FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
43/58
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
44/58
3 Select the target Fibre Channel card port and click the [Driver Parameters] tab.
4 Check the parameter values in the [Adapter Parameter] list.
Compare with the parameter values in the following tables, and correct the current value if necessary.Select the parameter whose value is to be corrected from the [Adapter Parameter] list and modify thevalue in the [Modify Adapter Parameter] area.
Chapter 3 Setup Procedure for PRIMEQUEST 500/400 Series3.2 For Fujitsu Emulex Fibre Channel Cards
44FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
45/58
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
46/58
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
47/58
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
48/58
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
49/58
Installing the Driver
Install the Fibre Channel card driver.
"B.5 Installing the Driver" (page 55)
"B.6 Checking the Driver Version" (page 55)
Installing the ETERNUS DX Driver
Install the ETERNUS DX driver.
"B.7 Installing the ETERNUS DX Driver" (page 56)
Checking the driver-related notes
"FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Win-dows"
After all of the required procedures in this manual are complete, proceed to the procedure that is de-scribed in "FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for
Windows".
Appendix B For Fujitsu QLogic Fibre Channel Cards (2Gbit/s)B.1 Workflow
49FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
50/58
B.2 Setting Up the Fibre Channel Cards
Install the Fibre Channel cards in the server, and acquire their physical addresses and World Wide Names(WWNs).
The physical address and WWN of a Fibre Channel card are required information in the following cases:when an error has occurred in the system, when using the ETERNUS DX storage systems (security function,host affinity function, etc.) to restrict server access, or when connecting the ETERNUS DX storage systemsand the server using a Fibre Channel switch.
Acquire the physical address and WWN when installing the Fibre Channel card, because they cannot bedetermined from BIOS and OS. Physical address and WWN must be assigned to "WWN instance manage-ment table for the server".
The workflow is shown below.
(1) Install the Fibre Channel card
(2) Turn on the server
(3) Acquire the physical address and WWN for the Fibre Channel card(4) Add a record for the server in the WWN instance management table for the server
(5) Set the Fibre Channel card BIOS
When installing two or more Fibre Channel cards in the server, first turn off the server, then repeat Steps (1)through (5) above for each Fibre Channel card to be installed.
The procedure is as follows:
1 Install the Fibre Channel card in the server.For the installation method, position (PCI bus slots), and notes regarding the Fibre Channel card, referto the Fibre Channel card manual or the user guide of the server.
2 Turn on the server, and press the [Ctrl] + [Q] keys while the following message is displayed.
QLogic Corporation
QLA23xx PCI Fibre Channel ROM BIOS Version *.**
Copyright(C) QLogic Corporation 2000. All rights reserved
www.qlogic.com
Press for Fast!UTIL
The "Fast!UTIL" program starts up (Startup may take longer than usual).
3 Check the value of [I/O Address] of the [Select Host Adapter] window.
The value of [I/O Address] is the physical address.
Adapter Type
QLA2xxx
I/O Address
3400
Select Host Adapter
Physical
address
4 Select [Configuration Settings] from the [Fast!UTIL Options] menu and press the [Enter] key.
5 Select [Host Adapter Settings] from the [Configuration Settings] menu and press the [Enter] key.
Appendix B For Fujitsu QLogic Fibre Channel Cards (2Gbit/s)B.2 Setting Up the Fibre Channel Cards
50FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
51/58
6 Check the value of [Adapter Port Name].
The value of [Adapter Port Name] is the Fibre Channel card WWN.Host Adapter Settings
BIOS Address
BIOS Revision
Adapter Serial NumberInterrupt Level
Adapter Port Name
Host Adapter BIOS
:xxxxx
:x.xx
:xxxxxx:xx
:200000E08B0214D0
:Disabled
7 Record the physical address and WWN in the "WWN instance management table for the server".
(found in "Appendix A WWN Instance Management Table for the Server (Blank)" (page 47)).
The following shows an example of this.
Host name Server#1
IP Address 192.168.0.10
Physical slot
name Fibre Channel card WWN Instance name Physical address Cable tag
slot0 20 00 00 E0 8B 02 14 D0 3400 SERV1_SLOT0 to SN200_1_port0
8 Set up the BIOS parameters for the Fibre Channel card.
Check the values for each parameter in the [Host Adapter Settings] window. See the following tablesand set each value. For details on how to set the values, refer to the BIOS Readme file and Fibre Chan-nel card user's guide.
Parameter Host Adapter settings value Remarks
BIOS Address Fixed for each card Settings cannot be changed.
BIOS Revision (*1)
Adapter Serial Number
Interrupt Level
Adapter Port Name
Host Adapter BIOS Enabled or Disabled Set "Enabled" for SAN Boot.
Set "Disabled" for non SAN Boot.
Frame Size 2048 If the current parameter values are dif-ferent, change them to the indicated
values.Loop Reset Delay 5Adapter Hard Loop ID Disabled
Hard Loop ID 0
Spinup Delay Disabled
Connection Options 0 or 1 For direct connection: 0 (*2)
For switch connection: 1 (*3)
Fibre Channel
Tape Support
Disabled If "Enabled" is displayed, change thevalue to "Disabled".
Data Rate 1 0: 1Gbit/s fixed
1: 2Gbit/s fixed
2: Auto-negotiated
Appendix B For Fujitsu QLogic Fibre Channel Cards (2Gbit/s)B.2 Setting Up the Fibre Channel Cards
51FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
52/58
*1: The BIOS version of the Fibre Channel card is displayed. Check that the BIOS version is the same asshown in "Server Support Matrix".
*2: When connecting directly to the ETERNUS DX storage systems via a Fibre Channel pass-throughblade
*3: When the Fibre Channel switch is connected to the ETERNUS DX storage systems via a Fibre Chan-nel pass-through blade or Fibre Channel switch blade.
9 Return to the [Configuration Settings] menu by pressing the [Esc] key.
10 Select [Advanced Adapter Settings] from the [Configuration Settings] menu and press the [Enter] key.
Compare with the parameter values in the following tables, and correct the current value if necessary.
Parameter Advanced HBA Parameter settings Remarks
Execution Throttle Arbitrary (*1)
(Up to 512 for each FC port of theETERNUS DX)
If the current parameter values are dif-ferent, change them to the indicatedvalues.
LUNs per Target 256
Enable LIP Reset No
Enable LIP Full Login Yes
Enable Target Reset Yes
Login Retry Count 8
Port Down Retry Count 45
Link Down Timeout 45
Extended Error Logging Disabled
RIO Operation Mode 0
Interrupt Delay Timer 0
EV Controller Order Disabled
*1: Recommended value = 512 (number of Fibre Channel ports that are connected to a single CAport) number of LUNs
(Round the result down)
Use the value of "8" if the actual result is lower.
Use the value of "254" if the actual result is higher.
11 Press the [Esc] key twice to return to the [Fast!UTIL Options] menu.
If the BIOS settings were changed, save the settings using [Save xxxxxx]. When two or more FibreChannel cards are installed in the server, select the second or later Fibre Channel card using the follow-ing steps, and set the BIOS of the selected card.
(1) Select [Select Host Adapter] from the [Fast!UTIL Options] menu and press the [Enter] key.
(2) Select the Fibre Channel card to be set (BIOS setting) in the [Select Host Adapter] window.
The [Fast!UTIL Options] menu appears. Then perform Step 3through Step 11.
12 Select [Exit Fast!UTIL] and press the [Enter] key.
Appendix B For Fujitsu QLogic Fibre Channel Cards (2Gbit/s)B.2 Setting Up the Fibre Channel Cards
52FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
53/58
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
54/58
4 Check the values for each parameter.
Selectable Boot
Boot Port Name, Lun
:Disabled
:0000000000000000,0
Selectable Boot Settings
Parameter Setting value Remarks
Selectable Boot Enabled or Disabled Set [Enabled] for SAN Boot.
Set [Disabled] for non SAN Boot.
Boot Port Name, Lun ETERNUS DX port WWN, LUN#
or 0000000000000000,0
The boot path (ETERNUS DX port WWN)and boot LUN# for SAN Boot are separated
by a comma. "0000000000000000,0" for non SAN Boot.
5 Return to the [Configuration Settings] menu by pressing the [Esc] key.
6 Press the [Esc] key twice to return to the [Fast!UTIL Options] menu.
If the settings were changed, save the settings using [Save xxxxxx].
When two or more Fibre Channel cards are installed in the server, select the second or later Fibre Chan-nel card using the following steps, and set the BIOS of the selected card.
(1) Select [Select Host Adapter] from the [Fast!UTIL Options] menu and press the [Enter] key.
Fast!UTIL Options
Configuration Settings
Scan Fibre Devices
Fibre Disk Utility
Select Host Adapter
Exit Fast!UTIL
Fast!UTIL Options
(2) Select the Fibre Channel card to be set (BIOS setting).
Adapter Type I/O AddressQLA2xxx
QLA2xxx
3400
3800
Select Host Adapter
(3) The [Fast!UTIL Options] menu appears. Then perform Step 1through Step 6.
7 Select [Exit Fast!UTIL] and press the [Enter] key.
Appendix B For Fujitsu QLogic Fibre Channel Cards (2Gbit/s)B.3 Setting Up SAN Boot
54FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
55/58
8 Select [Reboot System] and press the [Enter] key.
Reboot System
Return to Fast!UTIL
Exit Fast!UTIL
The server reboots.
To return to the [Fast!UTIL] menu, select [Return to Fast!UTIL].
B.4 Installing Windows
Refer to the documentation supplied with the product for Windows installation details.
B.5 Installing the Driver
Refer to the documentation provided with each Fibre Channel card for details on how to obtain and install aFibre Channel card driver for it.
B.6 Checking the Driver Version
Use the Device Manager to check the version of the Fibre Channel card driver.
1 In the Device Manager, go to [Storage controllers], and open the [Properties] of the Fibre Channel card.
2 Select the [Driver] tab, and open [Driver Details].
3 Select the driver file, and check its [File version].
If a different driver version is displayed from that shown in "Server Support Matrix", reinstall the driv-er.
Appendix B For Fujitsu QLogic Fibre Channel Cards (2Gbit/s)B.4 Installing Windows
55FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (Fibre Channel) for Windows
Copyright 2014 FUJITSU LIMITED
P3AM-6332-11ENZ0
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
56/58
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
57/58
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection-
(Fibre Channel) for Windows
Driver Settings for Fujitsu Fibre Channel Cards
P3AM-6332-11ENZ0
Date of issuance: December 2014Issuance responsibility: FUJITSU LIMITED
The content of this manual is subject to change without notice.
This manual was prepared with the utmost attention to detail. However, Fujitsu shall assume no responsibility for anyoperational problems as the result of errors, omissions, or the use of information in this manual.
Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any informationin this manual.
The content of this manual may not be reproduced or distributed in part or in its entirety without prior permission fromFujitsu.
-
7/23/2019 Server Connection- (Fibre Channel) - Fujitsu
58/58