service manual aep model - especarchive.espec.ws/files/sony cdx-gt610u_gt616u_gt617ue.pdf3...

SERVICE MANUAL

Sony CorporationeVehicle DivisionPublished by Sony Techno Create Corporation

AEP ModelUK Model

CDX-GT610U/GT616U

East European ModelCDX-GT617UE

9-887-473-022007C04-1© 2007.03

Ver. 1.1 2007.03

SPECIFICATIONS

CD player sectionSignal-to-noise ratio 120 dBFrequency response 10 – 20,000 HzWow and flutter Below measurable limit

Tuner sectionFMTuning range CDX-GT610U/GT616U:

87.5 – 108.0 MHzCDX-GT617UE:FM1/FM2: 87.5 – 108.0 MHz (at 50 kHz step)FM3: 65 – 74 MHz (at 30 kHz step)

Antenna terminal External antenna connectorIntermediate frequency 10.7 MHz/450 kHzUsable sensitivity 9 dBfSelectivity 75 dB at 400 kHzSignal-to-noise ratio 67 dB (stereo), 69 dB (mono)Harmonic distortion at 1 kHz

0.5% (stereo), 0.3% (mono)Separation 35 dB at 1 kHzFrequency response 30 – 15,000 Hz

MW/LWTuning range MW: 531 – 1,602 kHz

LW: 153 – 279 kHzAntenna terminal External antenna connectorIntermediate frequency 10.7 MHz/450 kHzSensitivity MW: 30 µV, LW: 40 µV

USB player sectionInterface USB (Full-speed)Maximum current 500 mA

Power amplifier sectionOutputs Speaker outputs (sure seal connectors)Speaker impedance 4 – 8 ohmsMaximum power output

50 W × 4 (at 4 ohms)

• The tuner and CD sections have no adjustments. Model Name Using Similar Mechanism CDX-GT410U/GT414U

CD Drive Mechanism Type MG-101U-188//Q

Optical Pick-up Name DAX-25A

– Continued on next page –

CDX-GT610U/GT616U/GT617UE

FM/MW/LW COMPACT DISC PLAYER

(Photo: CDX-GT610U)

2


SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTSWHOSE PART NUMBERS APPEAR AS SHOWN IN THISMANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCKOR BASE UNITThe laser diode in the optical pick-up block may suffer electrostaticbreakdown because of the potential difference generated by thecharged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic breakdown and also usethe procedure in the printed matter which is included in the repairparts.The flexible board is easily damaged and should be handled withcare.

NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused onthe disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission,observe from more than 30 cm away from the objective lens.

If the optical pick-up block is defective, please replace the wholeoptical pick-up block.Never turn the semi-fixed resistor located at the side of optical pick-up block.

SERVICE NOTES

CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardousradiation exposure.

GeneralOutputs Audio outputs terminal (front/rear)

Subwoofer output terminal (mono)Power antenna relay control terminalPower amplifier control terminal

Inputs Telephone ATT control terminalIllumination control terminalBUS control input terminalBUS audio input terminal/AUX IN terminalRemote controller input terminalAntenna input terminal

Tone controls Low: ±10 dB at 60 Hz (XPLOD)Mid: ±10 dB at 1 kHz (XPLOD)High: ±10 dB at 10 kHz (XPLOD)

Power requirements 12 V DC car battery (negative ground)Dimensions Approx. 178 × 50 × 180 mm

(7 1/8 × 2 × 7 1/8 in.) (w/h/d)Mounting dimensions Approx. 182 × 53 × 162 mm

(7 1/4 × 2 1/8 × 6 1/2 in.) (w/h/d)Mass Approx. 1.3 kg (3 lb. 5 oz.)Supplied accessories Card remote commander: RM-X151

Parts for installation and connections (1 set)

Design and specifications are subject to change withoutnotice.

US and foreign patents licensed from Dolby Laboratories. optical pick-up

semi-fixed resistor

Notes on Chip Component Replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be damaged

by heat.

TEST DISCSPlease use the following test discs for the check on the CD section.

YDES-18 (Part No. 3-702-101-01)PATD-012 (Part No. 4-225-203-01)

3


•UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size.)

: LEAD FREE MARKUnleaded solder has the following characteristics.• Unleaded solder melts at a temperature about 40°C higher than

ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350°C.Caution: The printed pattern (copper foil) may peel away if the

heated tip is applied for too long, so be careful!• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow)than ordinary solder so use caution not to let solder bridgesoccur such as on IC pins, etc.

• Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.

SERVO BOARDCN2

MAIN BOARDCN350 J-2502-076-1

EXTENSION CABLE AND SERVICE POSITIONWhen repairing or servicing this set, connect the jig (extension cable)as shown below.

• Connect the MAIN board (CN350) and the SERVO board (CN2)with the extension cable (Part No. J-2502-076-1).

This label is located on the bottom of the chassis.

This compact disc player is classified as a CLASS 1 LASERproduct. The CLASS 1 LASER PRODUCT label is located on theexterior.

• CD playbackYou can play CD-DA (also containing CD TEXT*), CD-R/CD-RW (MP3/WMA/AAC files also containing Multi Session) andATRAC CD (ATRAC3 and ATRAC3plus format).

Type of discs Label on the disc

CD-DA

MP3

WMA

AAC

ATRAC CD

* A CD TEXT disc is a CD-DA that includes information such asdisc, artist and track name.

4


TABLE OF CONTENTS

1. GENERALLocation of Controls ........................................................ 5Connections ..................................................................... 6

2. DISASSEMBLY2-1. Sub Panel Assy ................................................................ 112-2. CD Mechanism Block ..................................................... 112-3. Main Board ...................................................................... 122-4. Servo Board ..................................................................... 122-5. Chassis (T) Sub Assy ....................................................... 132-6. Roller Arm Assy .............................................................. 132-7. Chassis (OP) Assy ........................................................... 14

3. DIAGNOSIS FUNCTION ........................................ 15

4. DIAGRAMS4-1. Block Diagram –Main Section– ...................................... 194-2. Block Diagram –Display Section– .................................. 204-3. Printed Wiring Board –Main Section– ............................ 224-4. Schematic Diagram –Main Section (1/3)– ...................... 234-5. Schematic Diagram –Main Section (2/3)– ...................... 244-6. Schematic Diagram –Main Section (3/3)– ...................... 254-7. Printed Wiring Board –Sub Section– .............................. 264-8. Schematic Diagram –Sub Section– ................................. 274-9. Printed Wiring Board –Key Section– .............................. 284-10. Schematic Diagram –Key Section– ................................. 29

5. EXPLODED VIEWS5-1. Main Section .................................................................... 335-2. Front Panel Section ......................................................... 345-3. CD Mechanism Section (MG-101U-188//Q) .................. 35

6. ELECTRICAL PARTS LIST .................................. 36

NOTE FOR REPLACEMENT OF THE USB CONNECTOR(J11)To replace the USB connector requires alignment.1. Insert the USB connector into the front panel.2. Place the KEY board on the front panel and align the terminals

of the USB connector with the holes in the KEY board.3. Solder the four terminals of the connector.

NOTE FOR REPLACEMENT OF THE SERVO BOARDWhen repairing, the complete SERVO board (A-1206-357-A) shouldbe replaced since any parts in the SERVO board cannot be repaired.

NOTE FOR THE 20-PIN CONNECTOR (CN901)Do not use alcohol to clean the 20-pin connector (CN901) connectingthe front panel with the main body.Do not touch the connector directly with your bare hand. Poor contactmay be caused.

KEY board

front panel

USB (socket) connector

Ver. 1.1

5

CDX-GT610U/GT616U/GT617UESECTION 1GENERAL This section is extracted

from instruction manual.

• LOCATION OF CONTROLS• CDX-GT610U/GT616U

• CDX-GT617UE

6

Location of controls and basic operations

Main unit

Front panel removed

Card remote commander RM-X151

Refer to the pages listed for details. The corresponding buttons on the card remote commander control the same functions as those on the unit.

A OFF buttonTo power off; stop the source.

B DSO button 4To select the DSO mode (1, 2, 3 or OFF). The larger the number, the more enhanced the effect.

C Volume control dial/select button 12To adjust volume (rotate); select setup items (press and rotate).

D SOURCE buttonTo power on; change the source (Radio/CD/MD*1/USB/AUX).

E Display window

F USB terminal 11To connect to the USB device.

G OPEN button 5

OFF OPEN

DSPL AF/TA

SEEK SEEK

PAUSEGP/ALBM REP SHUF BBE MP

PUSH SELECT

1 2 3 4 5 6

MODE

DSO

PTY

EQ3

SOURCE

1

q;9 qa qd qgqs

2

qf

4 5

8

6 73

CDX-GT616UCDX-GT610U

RESET

qj qkqh

OFF

DSPL SCRL

SELSOURCE MODE

1 32

4 65

ATT

VOL+

–

+

–

4 wsqs

1

ql

qd

wa

w;

wg

wd

wf

7

H EQ3 (equalizer) button 12To select an equalizer type (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF).

I Receptor for the card remote commander

J SEEK –/+ buttonsCD/MD*1/USB*2:To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); reverse/fast-forward a track (press and hold).Radio:To tune in stations automatically (press); find a station manually (press and hold).

K PTY (Program Type) button 10To select PTY in RDS.

L MODE button 8, 11, 13To select the radio band (FM/MW/LW); select the unit*3; select the play mode*4.

M DSPL (display) button 8, 9, 11To change display items.

N Number buttonsCD/MD*1/USB*2:(1)/(2): GP*5/ALBM*6 –/+

To skip albums (press); skip albums continuously (press and hold).*7

(3): REP 8, 11, 13(4): SHUF 8, 11, 13(5): BBE MP*8 2

To activate the BBE MP function, set “BBE MP-ON.” To cancel, set “BBE MP-OFF.”

(6): PAUSE*8

To pause playback. To cancel, press again.

Radio:To receive stored stations (press); store stations (press and hold).

O AF (Alternative Frequencies)/TA (Traffic Announcement) button 9To set AF and TA in RDS.

P RESET button 4

Q Z (eject) button 5To eject the disc.

R Disc slot 5To insert the disc.

The following buttons on the card remote commander have also different buttons/functions from the unit. Remove the insulation film before use (page 4).

ql < (.)/, (>) buttonsTo control CD/radio/MD/USB, the same as (SEEK) –/+ on the unit.

w; VOL (volume) +/– buttonTo adjust volume.

wa ATT (attenuate) buttonTo attenuate the sound. To cancel, press again.

ws SEL (select) buttonThe same as the select button on the unit.

wd M (+)/m (–) buttonsTo control CD, the same as (1)/(2) (GP/ALBM –/+) on the unit.

wf SCRL (scroll) button 8, 11To scroll the display item.

wg Number buttonsTo receive stored stations (press); store stations (press and hold).

*1 When an MD changer is connected.*2 When a USB device is connected.*3 When a CD/MD changer is connected.*4 When an ATRAC Audio Device is connected.*5 When an ATRAC CD is played.*6 When an MP3/WMA/AAC is played. *7 If the changer/USB is connected, the operation is

different, see page 13.*8 When playing back on this unit and a USB device.

Notes• When ejecting/inserting a disc, keep any USB

devices disconnected to avoid damage to the disc.• If the unit is turned off and the display disappears, it

cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first.

TipFor details on how to replace the battery, see “Replacing the lithium battery of the card remote commander” on page 17.

About USB capWhen not using the USB terminal (F), use the supplied USB cap to prevent dust or dirt entering.Keep the USB cap out of the reach of children to prevent accidental swallowing.

6

Location of controls and basic operations

Main unit

Front panel removed

Card remote commander RM-X151

Refer to the pages listed for details. The corresponding buttons on the card remote commander control the same functions as those on the unit.

A OFF buttonTo power off; stop the source.

B DSO button 4To select the DSO mode (1, 2, 3 or OFF). The larger the number, the more enhanced the effect.

C Volume control dial/select button 12To adjust volume (rotate); select setup items (press and rotate).

D SOURCE buttonTo power on; change the source (Radio/CD/MD*1/USB/AUX).

E Display window

F USB terminal 11To connect to the USB device.

G OPEN button 5

OFF OPEN

DSPL AF/TA

SEEK SEEK

PAUSEGP/ALBM REP SHUF BBE MP

PUSH SELECT

1 2 3 4 5 6

MODE

DSO

PTY

EQ3

SOURCE

1

q;9 qa qd qgqs

2

qf

4 5

8

6 73

CDX-GT617UE

RESET

qj qkqh

OFF

DSPL SCRL

SELSOURCE MODE

1 32

4 65

ATT

VOL+

–

+

–

4 wsqs

1

ql

qd

wa

w;

wg

wd

wf

7

H EQ3 (equalizer) button 12To select an equalizer type (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF).

I Receptor for the card remote commander

J SEEK –/+ buttonsCD/MD*1/USB*2:To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); reverse/fast-forward a track (press and hold).Radio:To tune in stations automatically (press); find a station manually (press and hold).

K PTY (Program Type) button 10To select PTY in RDS.

L MODE button 8, 11, 13To select the radio band (FM/MW/LW); select the unit*3; select the play mode*4.

M DSPL (display) button 8, 9, 11To change display items.

N Number buttonsCD/MD*1/USB*2:(1)/(2): GP*5/ALBM*6 –/+

To skip albums (press); skip albums continuously (press and hold).*7

(3): REP 8, 11, 13(4): SHUF 8, 11, 13(5): BBE MP*8 2

To activate the BBE MP function, set “BBE MP-ON.” To cancel, set “BBE MP-OFF.”

(6): PAUSE*8

To pause playback. To cancel, press again.

Radio:To receive stored stations (press); store stations (press and hold).

O AF (Alternative Frequencies)/TA (Traffic Announcement) button 9To set AF and TA in RDS.

P RESET button 4

Q Z (eject) button 5To eject the disc.

R Disc slot 5To insert the disc.

The following buttons on the card remote commander have also different buttons/functions from the unit. Remove the insulation film before use (page 4).

ql < (.)/, (>) buttonsTo control CD/radio/MD/USB, the same as (SEEK) –/+ on the unit.

w; VOL (volume) +/– buttonTo adjust volume.

wa ATT (attenuate) buttonTo attenuate the sound. To cancel, press again.

ws SEL (select) buttonThe same as the select button on the unit.

wd M (+)/m (–) buttonsTo control CD, the same as (1)/(2) (GP/ALBM –/+) on the unit.

wf SCRL (scroll) button 8, 11To scroll the display item.

wg Number buttonsTo receive stored stations (press); store stations (press and hold).

*1 When an MD changer is connected.*2 When a USB device is connected.*3 When a CD/MD changer is connected.*4 When an ATRAC Audio Device is connected.*5 When an ATRAC CD is played.*6 When an MP3/WMA/AAC is played. *7 If the changer/USB is connected, the operation is

different, see page 13.*8 When playing back on this unit and a USB device.

Notes• When ejecting/inserting a disc, keep any USB

devices disconnected to avoid damage to the disc.• If the unit is turned off and the display disappears, it

cannot be operated with the card remote commander unless (SOURCE) on the unit is pressed, or a disc is inserted to activate the unit first.

TipFor details on how to replace the battery, see “Replacing the lithium battery of the card remote commander” on page 17.

About USB capWhen not using the USB terminal (F), use the supplied USB cap to prevent dust or dirt entering.Keep the USB cap out of the reach of children to prevent accidental swallowing.

6


• CONNECTIONS• CDX-GT610U/GT616U

AUDIO OUTFRONT

AUDIO OUTREAR

SUB OUT (MONO)

BUS AUDIO IN

BUS CONTROL IN

BUS AUDIO IN

BUS CONTROL IN

A

B

* not supplied nicht mitgeliefertnon fourninon in dotazioneniet bijgeleverd

Source selector*Signalquellenwähler*Sélecteur de source*

Selettore di fonte*Geluidsbronkiezer*

XA-C40

Voorbeeldaansluitingen Opmerkingen (2-A)• Sluit eerst de aarddraad aan voordat u de versterker aansluit.• U hoort de pieptoon alleen als de ingebouwde versterker wordt

gebruikt.

Tip (2-B- )Om twee of meer CD/MD-wisselaars aan te sluiten, hebt u de geluidsbronkiezer XA-C40 (niet bijgeleverd) nodig.

Exemple de raccordement Remarques (2-A) • Raccordez d’abord le câble de mise à la masse avant de

connecter l’amplifi cateur.• L’alarme est émise uniquement lorsque l’amplifi cateur intégré

est utilisé.

Conseil (2-B- )Dans le cas du raccordement de deux changeurs de CD/MD ou plus, le sélecteur de source XA-C40 (non fourni) est indispensable.

Anschlussbeispiel Hinweise (2-A)• Schließen Sie unbedingt zuerst das Massekabel an, bevor Sie

den Verstärker anschließen.• Der Warnton wird nur ausgegeben, wenn der integrierte

Verstärker verwendet wird.

Tipp (2-B- )Zum Anschließen von zwei oder mehr CD/MD-Wechslern wird der Signalquellenwähler XA-C40 (nicht mitgeliefert) benötigt.

Esempio di collegamento Note (2-A) • Assicurarsi di collegare il cavo di terra prima di collegare

l’apparecchio all’amplifi catore.• L’allarme viene emesso solo se è in uso l’amplifi catore

incorporato.

Suggerimento (2-B- )Per collegare due o più cambia CD/MD, occorre utilizzare il selettore di fonte XA-C40 (non in dotazione).

Connection example Notes (2-A)• Be sure to connect the ground (earth) lead before connecting

the amplifi er.• The alarm will only sound if the built-in amplifi er is used.

Tip (2-B- )For connecting two or more CD/MD changers, the source selector XA-C40 (not supplied) is necessary.

7


L

R

AUDIOOUT

REAR

AUDIOOUT

FRONT

BUSAUDIO

IN

5 7

4 8

1 3 5 7

2 4 6 8

A

B

6

AUDIO OUTREAR

BUSCONTROL IN

REMOTEIN

AUDIO OUTFRONT

BUS AUDIO IN/ AUX IN*3

SUB OUT (MONO)*1 from car antenna (aerial) von Autoantenne de l’antenne de la voiture dall’antenna dell’auto van een auto-antenne

Fuse (10 A)Sicherung (10 A)Fusible (10 A)Fusibile (10 A)Zekering (10 A)

AMP REM

Light blueHellblauBleu cielAzzurroLichtblauw

Blue/white stripedBlauweiß gestreiftRayé bleu/blancRigato blu e biancoBlauw/wit gestreept

from the car’s power connectorvom Stromanschluss des Fahrzeugsdu connecteur d’alimentation de la voituredal connettore di alimentazione dell’autovan de autovoedingsstekker

ATT

See “Power connection diagram” on the reverse side for details.

Näheres dazu fi nden Sie im „Stromanschlussdiagramm“. Blättern Sie dazu bitte um.

Voir le « Schéma de raccordement d’alimentation » au verso pour plus de détails.

Per ulteriori informazioni, vedere “Diagramma dei collegamenti di alimentazione” che si trova sul retro.

Zie "Voedingsaansluitschema" op de achterkant voor meer details.

Max. supply current 0.3 Amax. Versorgungsstrom 0,3 ACourant d’alimentation maximum 0,3 AAlimentazione massima fornita 0,3 AMax. voedingsstroom 0,3 A

Negative polarity positions 2, 4, 6, and 8 have striped leads.An den negativ gepolten Positionen 2, 4, 6 und 8 befi nden sich gestreifte Adern.Les positions de polarité négative 2, 4, 6 et 8 sont dotées de cordons rayés.Le posizioni a polarità negativa 2, 4, 6 e 8 hanno cavi rigati.De posities voor negatieve polariteit (2, 4, 6 en 8) hebben gestreepte kabels.

1PurpleViolettMauveViolaPaars

+

Speaker, Rear, RightLautsprecher hinten rechtsHaut-parleur, arrière, droit

Diffusore, posteriore, destroLuidspreker, achter, rechts

5WhiteWeißBlanc

BiancoWit

+

Speaker, Front, LeftLautsprecher vorne links

Haut-parleur, avant, gaucheDiffusore, anteriore, sinistro

Luidspreker, voor, links

2 –

Speaker, Rear, RightLautsprecher hinten rechtsHaut-parleur, arrière, droit

Diffusore, posteriore, destroLuidspreker, achter, rechts

6 –

Speaker, Front, LeftLautsprecher vorne links

Haut-parleur, avant, gaucheDiffusore, anteriore, sinistro

Luidspreker, voor, links

3GrayGrauGris

GrigioGrijs

+

Speaker, Front, RightLautsprecher vorne rechtsHaut-parleur, avant, droit

Diffusore, anteriore, destroLuidspreker, voor, rechts

7GreenGrünVert

VerdeGroen

+

Speaker, Rear, LeftLautsprecher hinten links

Haut-parleur, arrière, gaucheDiffusore, posteriore, sinistro

Luidspreker, achter, links

4 –

Speaker, Front, RightLautsprecher vorne rechtsHaut-parleur, avant, droit

Diffusore, anteriore, destroLuidspreker, voor, rechts

8 –

Speaker, Rear, LeftLautsprecher hinten links

Haut-parleur, arrière, gaucheDiffusore, posteriore, sinistro

Luidspreker, achter, links

*2

Supplied with the CD/MD changerMit dem CD/MD-Wechsler geliefertFourni avec le changeur de CD/MDIn dotazione con il cambia CD/MDGeleverd met de CD/MD-wisselaar

Source selector(not supplied)

Signalquellenwähler(nicht mitgeliefert)

Sélecteur de source(non fourni)

Selettore di fonte(non in dotazione)Geluidsbronkiezer(niet bijgeleverd)

XA-C40

from the car’s speaker connectorvom Lautsprecheranschluss des Fahrzeugsdu connecteur de haut-parleur de la voituredal connettore del diffusore dellíautovan de autoluidsprekerstekker

Positions 1, 2 and 3 do not have pins.An Position 1, 2 und 3 befi nden sich keine Stifte.Les positions 1, 2 et 3 ne comportent pas de broches.Le posizioni 1, 2 e 3 non hanno piedini.De posities 1, 2 en 3 hebben geen pins.

4

YellowGelb

JauneGialloGeel

continuous power supplypermanente Stromversorgung

alimentation continuealimentazione continua

continu voeding

5

BlueBlauBleuBlu

Blauw

power antenna (aerial) controlMotorantennensteuerung

antenne électriquecomando dell’antenna elettrica

automatische antenne

6

Orange/WhiteOrangeweiß

gestreiftRayé orange/

blancArancione/

biancoOranje/wit

switched illumination power supplygeschaltete

Beleuchtungsstromversorgungalimentation de l’éclairage

commutéalimentazione illuminazione

commutatageschakelde voeding voor

verlichting

7

RedRot

RougeRossoRood

switched power supplygeschaltete Stromversorgung

alimentation commutéealimentazione commutata

geschakelde voeding

8

BlackSchwarz

NoirNeroZwart

ground (earth)Massemasseterra

aarding

*2

*5

*1 Note for the antenna (aerial) connectingIf your car antenna (aerial) is an ISO (International Organization for Standardization) type, use the supplied adaptor 2 to connect it. First connect the car antenna (aerial) to the supplied adaptor, then connect it to the antenna (aerial) jack of the master unit.

*2 RCA pin cord (not supplied)*3 Be sure to match the color-coded cord

for audio to the appropriate jacks from the unit. If you connect an optional CD/MD changer, you cannot use AUX IN terminal.

*4 Supplied with the auxiliary equipment*5 Insert with the cord upwards.*6 Supplied with XA-C40

*1 Hinweis zum Anschließen der AntenneWenn Ihre Fahrzeugantenne der ISO-Norm (ISO = International Organization for Standardization - Internationale Normungsgemeinschaft) entspricht, schließen Sie sie mithilfe des mitgelieferten Adapters 2 an. Verbinden Sie zuerst die Fahrzeugantenne mit dem mitgelieferten Adapter und verbinden Sie diesen dann mit der Antennenbuchse des Hauptgeräts.

*2 Cinchkabel (nicht mitgeliefert)*3 Achten Sie darauf, das farbcodierte

Audiokabel mit den richtigen Buchsen am Gerät zu verbinden. Wenn ein gesondert erhältlicher CD/MD-Wechsler angeschlossen ist, kann der Anschluss AUX IN nicht verwendet werden.

*4 Mit den Zusatzgeräten mitgeliefert*5 Mit dem Kabel nach oben einsetzen.*6 Mit dem XA-C40 geliefert

*1 Remarque sur le raccordement de l’antenneSi votre antenne de voiture est de type ISO (Organisation internationale de normalisation), utilisez l’adaptateur fourni

pour la r2 accorder. Raccordez d’abord l’antenne de voiture à l’adaptateur fourni et, ensuite, à la prise d’antenne de l’appareil principal.

*2 Cordon à broche RCA (non fourni)*3 Veillez à faire correspondre le code de

couleur du cordon audio à celui des fiches correspondantes de l’appareil. Si vous raccordez un changeur de CD/MD en option, vous ne pouvez pas utiliser la borne AUX IN.

*4 Fourni avec l’appareil auxiliaire*5 Insérez avec le câble vers le haut.*6 Fourni avec le XA-C40

*1 Opmerking bij de antenne-aansluitingIndien uw auto is uitgerust met een antenne van het type ISO (International Organization for Standardization), moet u die aansluiten met behulp van de bijgeleverde adapter 2. Sluit eerst de auto-antenne aan op de bijgeleverde adapter en vervolgens de antennestekker op het hoofdtoestel.

*2 Tulpstekkersnoer (niet bijgeleverd)*3 Zorg ervoor dat de kleurcode van het

snoer voor audio overeenkomt met de bijbehorende aansluitingen op het apparaat. Als u een optionele CD/MD-wisselaar aansluit, kunt u de AUX IN aansluiting niet gebruiken.

*4 Geleverd bij de optionele apparatuur*5 Plaatsen met het snoer naar boven.*6 Geleverd met de XA-C40

Auxiliary equipment such as portable DVD player (not supplied)Zusätzliche Geräte wie z. B. der tragbare DVD-Player (nicht mitgeliefert)Equipement auxiliaire comme un lecteur de DVD portable (non fourni)Apparecchio ausiliario quale un lettore DVD portatile (non in dotazione)Optionele apparatuur zoals de draagbare DVD-speler (niet bijgeleverd)

*1 Nota per il collegamento dell’antennaSe l’antenna dell’auto è di tipo ISO (International Organization for Standardization), utilizzare l’adattatore

in dotazione per collegar2 la. Collegare prima l’antenna della macchina all’adattatore in dotazione, quindi collegarla alla presa dell’antenna dell’apparecchio principale.

*2 Cavo a piedini RCA (non in dotazione)*3 Assicurarsi che i cavi differenziati in

base al colore per l’audio corrispondano alle prese appropriate dell’apparecchio. Se viene collegato un cambia CD/MD opzionale, non è possibile utilizzare il terminale AUX IN.

*4 in dotazione con l’apparecchio ausiliario*5 Inserire con il cavo rivolto verso l’alto.*6 In dotazione con il modello XA-C40

*6

*2

*4

*6

2

3

Aansluitschema

A Naar AMP REMOTE IN van een optionele eindversterkerDeze aansluiting is alleen bedoeld voor versterkers. Door een ander systeem aan te sluiten kan het apparaat worden beschadigd.

B Naar het interface-snoer van een autotelefoon

WaarschuwingIndien u een elektrische antenne hebt zonder relaiskast, kan het aansluiten van dit apparaat met het bijgeleverde netsnoer 3 de antenne beschadigen.Opmerkingen over de bedienings- en voedingskabels• De antennevoedingskabel (blauw) levert +12 V gelijkstroom

wanneer u de tuner inschakelt of de AF (Alternative Frequency) of TA (Traffi c Announcement) functie activeert.

• Wanneer uw auto is uitgerust met een FM/MW/LW-antenne in de achterruit/zijruit, moet u de antennevoedingskabel (blauw) of de hulpvoedingskabel (rood) aansluiten op de voedingsingang van de bestaande antenneversterker. Raadpleeg uw dealer voor meer details.

• Met dit apparaat is het niet mogelijk een automatische antenne zonder relaiskast te gebruiken.

Instandhouden van het geheugenZolang de gele stroomdraad is aangesloten, blijft de stroomvoorziening van het geheugen intact, ook wanneer het contact van de auto wordt uitgeschakeld.

Opmerkingen betreffende het aansluiten van de luidsprekers• Zorg dat het apparaat is uitgeschakeld, alvorens de

luidsprekers aan te sluiten.• Gebruik luidsprekers met een impedantie van 4 tot 8 Ohm

en let op dat die het vermogen van de versterker kunnen verwerken. Als u dit niet doet, kunnen de luidsprekers ernstig beschadigd raken.

• Verbind in geen geval de aansluitingen van de luidsprekers met het chassis van de auto en sluit de aansluitingen van de rechter- en linkerluidspreker niet op elkaar aan.

• Verbind de aarddraad van dit apparaat niet met de negatieve (–) aansluiting van de luidspreker.

• Probeer nooit de luidsprekers parallel aan te sluiten.• Sluit geen actieve luidsprekers (met ingebouwde versterkers)

aan op de luidsprekeraansluiting van dit apparaat. Dit zal leiden tot beschadiging van de actieve luidsprekers. Sluit dus altijd uitsluitend luidsprekers zonder ingebouwde versterker aan.

• Om defecten te vermijden mag u de bestaande luidsprekerbedrading in uw auto niet gebruiken wanneer er een gemeenschappelijke negatieve (–) draad is voor de rechter- en linkerluidsprekers.

• Verbind de luidsprekerdraden niet met elkaar.

Opmerking over aansluitenAls de luidspreker en versterker niet correct zijn aangesloten, wordt "FAILURE" in het display weergegeven. In dit geval moet u zorgen dat de luidspreker en versterker correct zijn aangesloten.

Schémas de raccordement

A Au niveau du AMP REMOTE IN d’un amplifi cateur de puissance facultatifCe raccordement existe seulement pour les amplifi cateurs. Le raccordement à tout autre système peut endommager l’appareil.

B Vers le cordon de liaison d’un téléphone de voiture

AvertissementSi vous disposez d’une antenne électrique sans boîtier de relais, le branchement de cet appareil au moyen du cordon d’alimentation fourni 3 risque d’endommager l’antenne.Remarques sur les câbles de commande et d’alimentation• Le câble de commande (bleu) fournit du courant continu de

+12 V lorsque vous mettez le tuner sous tension ou lorsque vous activez la fonction AF (fréquence alternative) ou TA (informations de circulation).

• Lorsque votre voiture est équipée d’une antenne FM/MW (GO)/LW (PO) intégrée dans la vitre arrière/latérale, raccordez le câble de commande d’antenne (bleu) ou l’entrée d’alimentation des accessoires (rouge) au bornier de l’amplifi cateur d’antenne existant. Pour plus de détails, consultez votre revendeur.

• Une antenne électrique sans boîtier de relais ne peut pas être utilisée avec cet appareil.

Raccordement pour la conservation de la mémoireLorsque le câble de commande d’antenne jaune est connecté, le circuit de la mémoire est alimenté en permanence même si la clé de contact est en position d’arrêt.

Remarques sur le raccordement des haut-parleurs• Avant de raccorder les haut-parleurs, mettre l’appareil hors

tension.• Utiliser des haut-parleurs ayant une impédance de 4 à 8 ohms

et une capacité adéquate sous peine de les endommager.• Ne pas raccorder les bornes du système de haut-parleurs au

châssis de la voiture et ne pas connecter les bornes du haut-parleur droit à celles du haut-parleur gauche.

• Ne pas raccorder le câble de mise à la masse de cet appareil à la borne négative (–) du haut-parleur.

• Ne pas tenter de raccorder les haut-parleurs en parallèle.• Connecter uniquement des haut-parleurs passifs. La

connexion de haut-parleurs actifs (avec des amplifi cateurs intégrés) aux bornes des haut-parleurs pourrait endommager l’appareil.

• Pour éviter tout problème de fonctionnement, n’utilisez pas les câbles des haut-parleurs intégrés installés dans votre voiture si l’appareil dispose d’un câble négatif commun (–) pour les haut-parleurs droit et gauche.

• Ne raccordez pas entre eux les cordons des haut-parleurs de l’appareil.

Remarque sur le raccordementSi les enceintes et l’amplifi cateur ne sont pas raccordés correctement, le message « FAILURE » s’affi che. Dans ce cas, assurez-vous que les enceintes et l’amplifi cateur sont raccordés correctement.

Anschlussdiagramm

A An AMP REMOTE IN des gesondert erhältlichen EndverstärkersDieser Anschluss ist ausschließlich für Verstärker gedacht. Schließen Sie nichts anderes daran an. Andernfalls kann das Gerät beschädigt werden.

B An Schnittstellenkabel eines Autotelefons

WarnungWenn Sie eine Motorantenne ohne Relaiskästchen verwenden, kann durch Anschließen dieses Geräts mit dem mitgelieferten Stromversorgungskabel 3 die Antenne beschädigt werden.Hinweise zu den Steuer- und Stromversorgungsleitungen• Die Motorantennen-Steuerleitung (blau) liefert +12 V

Gleichstrom, wenn Sie den Tuner einschalten oder die AF- (Alternativfrequenzsuche) oder die TA-Funktion (Verkehrsdurchsagen) aktivieren.

• Wenn das Fahrzeug mit einer in der Heck-/Seitenfensterscheibe integrierten FM (UKW)/MW/LW-Antenne ausgestattet ist, schließen Sie die Motorantennen-Steuerleitung (blau) oder die Zubehörstromversorgungsleitung (rot) an den Stromversorgungsanschluss des vorhandenen Antennenverstärkers an. Näheres dazu erfahren Sie bei Ihrem Händler.

• Es kann nur eine Motorantenne mit Relaiskästchen angeschlossen werden.

Stromversorgung des SpeichersWenn die gelbe Stromversorgungsleitung angeschlossen ist, wird der Speicher stets (auch bei ausgeschalteter Zündung) mit Strom versorgt.

Hinweise zum Lautsprecheranschluss• Schalten Sie das Gerät aus, bevor Sie die Lautsprecher

anschließen.• Verwenden Sie Lautsprecher mit einer Impedanz zwischen 4 und

8 Ohm und ausreichender Belastbarkeit. Ansonsten können die Lautsprecher beschädigt werden.

• Verbinden Sie die Lautsprecheranschlüsse nicht mit dem Wagenchassis und verbinden Sie auch nicht die Anschlüsse des rechten mit denen des linken Lautsprechers.

• Verbinden Sie die Masseleitung dieses Geräts nicht mit dem negativen (–) Lautsprecheranschluss.

• Versuchen Sie nicht, Lautsprecher parallel anzuschließen.• An die Lautsprecheranschlüsse dieses Geräts dürfen nur

Passivlautsprecher angeschlossen werden. Schließen Sie keine Aktivlautsprecher (Lautsprecher mit eingebauten Verstärkern) an, da das Gerät sonst beschuadigt werdenkönnte.

• Um Fehlfunktionen zu vermeiden, verwenden Sie nicht die im Fahrzeug installierten, integrierten Lautsprecherleitungen, wenn am Ende eine gemeinsame negative (–) Leitung für den rechten und den linken Lautsprecher verwendet wird.

• Verbinden Sie nicht die Lautsprecherkabel des Geräts miteinander.

Hinweis zum AnschließenWenn Lautsprecher und Verstärker nicht richtig angeschlossen sind, erscheint „FAILURE“ im Display. Vergewissern Sie sich in diesem Fall, dass Lautsprecher und Verstärker richtig angeschlossen sind.

Schema di collegamento

A A AMP REMOTE IN di un amplifi catore di potenza opzionale Questo collegamento è riservato esclusivamente agli amplifi catori. Non collegare un tipo di sistema diverso onde evitare di causare danni all’apparecchio.

B Al cavo di interfaccia di un telefono per auto

AvvertenzaQuando si collega l’apparecchio con il cavo di alimentazione in dotazione 3, si potrebbe danneggiare l’antenna elettrica se questa non dispone di scatola a relè.Note sui cavi di controllo e di alimentazione• Il cavo (blu) di controllo dell’antenna elettrica fornisce

alimentazione pari a +12 V CC quando si attiva il sintonizzatore oppure la funzione TA (notiziario sul traffi co) o AF (frequenza alternativa).

• Se l’automobile è dotata di antenna FM/MW/LW incorporata nel vetro posteriore/laterale, collegare il cavo (blu) di controllo dell’antenna elettrica o il cavo (rosso) di ingresso dell’alimentazione accessoria al terminale di alimentazione del preamplifi catore dell’antenna esistente. Per ulteriori informazioni, consultare il proprio fornitore.

• Non è possibile usare un’antenna elettrica senza scatola a relè con questo apparecchio.

Collegamento per la conservazione della memoriaQuando il cavo di ingresso alimentazione giallo è collegato, viene sempre fornita alimentazione al circuito di memoria anche quando l’interruttore di accensione è spento.

Note sul collegamento dei diffusori• Prima di collegare i diffusori spegnere l’apparecchio.• Usare diffusori di impedenza compresa tra 4 e 8 ohm e con

capacità di potenza adeguata, altrimenti i diffusori potrebbero venire danneggiati.

• Non collegare i terminali del sistema diffusori al telaio dell’auto e non collegare i terminali del diffusore destro a quelli del diffusore sinistro.

• Non collegare il cavo di terra di questo apparecchio al terminale negativo (–) del diffusore.

• Non collegare i diffusori in parallelo.• Assicurarsi di collegare soltanto diffusori passivi, poiché

il collegamento di diffusori attivi, dotati di amplifi catori incorporati, ai terminali dei diffusori potrebbe danneggiare l’apparecchio.

• Per evitare problemi di funzionamento, non utilizzare i cavi dei diffusori incorporati installati nell’automobile se l’apparecchio condivide un cavo comune negativo (–) per i diffusori destro e sinistro.

• Non collegare fra loro i cavi dei diffusori dell’apparecchio.

Nota sui collegamentiSe l’amplifi catore e il diffusore non sono collegati correttamente, “FAILURE” viene visualizzato nel display. In tal caso, accertarsi che l’amplifi catore e il diffusore siano collegati correttamente.

Connection diagram

A To AMP REMOTE IN of an optional power amplifi erThis connection is only for amplifi ers. Connecting any other system may damage the unit.

B To the interface cable of a car telephone

WarningIf you have a power antenna (aerial) without a relay box, connecting this unit with the supplied power connecting lead 3 may damage the antenna (aerial).Notes on the control power and suppy leads• The power antenna (aerial) control lead (blue) supplies +12 V

DC when you turn on the tuner, or when you activate the AF (Alternative Frequency) or TA (Traffi c Announcement) function.

• When your car has built-in FM/MW/LW antenna (aerial) in the rear/side glass, connect the power antenna (aerial) control lead (blue) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer.

• A power antenna (aerial) without a relay box cannot be used with this unit.

Memory hold connectionWhen the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.

Notes on speaker connection• Before connecting the speakers, turn the unit off.• Use speakers with an impedance of 4 to 8 ohms, and with

adequate power handling capacities to avoid its damage.• Do not connect the speaker terminals to the car chassis, or

connect the terminals of the right speakers with those of the left speaker.

• Do not connect the ground (earth) lead of this unit to the negative (–) terminal of the speaker.

• Do not attempt to connect the speakers in parallel.• Connect only passive speakers. Connecting active speakers

(with built-in amplifi ers) to the speaker terminals may damage the unit.

• To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers.

• Do not connect the unit’s speaker leads to each other.

Note on connectionIf speaker and amplifi er are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifi er are connected correctly.

8


• CDX-GT617UE

AUDIO OUTFRONT

AUDIO OUTREAR

SUB OUT (MONO)

BUS AUDIO IN

BUS CONTROL IN

A

B

BUS AUDIO IN

BUS CONTROL IN

Source selector**

XA-C40

* not supplied

Connection example Notes (2-A)• Be sure to connect the ground (earth) lead before connecting

the amplifi er.• The alarm will only sound if the built-in amplifi er is used.

Tip (2-B- )For connecting two or more CD/MD changers, the source selector XA-C40 (not supplied) is necessary.

9


L

R

AUDIOOUT

REAR

AUDIOOUT

FRONT

BUSAUDIO

IN

BUSCONTROL IN

1 3 5 7

2 4 6 8

5 7

4 86

AUDIO OUTREAR

REMOTEIN

AUDIO OUTFRONT

BUS AUDIO IN/ AUX IN*3

SUB OUT (MONO)

Negative polarity positions 2, 4, 6, and 8 have striped leads.

1Purple

+ Speaker, Rear, Right 5White

+ Speaker, Front, Left

2 – Speaker, Rear, Right 6 – Speaker, Front, Left

3Grey

+ Speaker, Front, Right 7Green

+ Speaker, Rear, Left

4 – Speaker, Front, Right 8 – Speaker, Rear, Left

AMP REM

Max. supply current 0.3 A

Fuse (10 A)

Blue/white striped

*2

Light blue

from the car’s power connector

See “Power connection diagram” on the reverse side for details.

*1 Note for the antenna (aerial) connectingIf your car antenna (aerial) is an ISO (International Organization for Standardization) type, use the supplied adaptor 2 to connect it. First connect the car antenna (aerial) to the supplied adaptor, then connect it to the antenna (aerial) jack of the master unit.

*2 RCA pin cord (not supplied)*3 Be sure to match the color-coded cord for

audio to the appropriate jacks from the unit. If you connect an optional CD/MD changer, you cannot use AUX IN terminal.

*4 Supplied with the auxiliary equipment*5 Insert with the cord upwards*6 Supplied with XA-C40

from the car’s speaker connector

ATT

*2

Source selector(not supplied)

XA-C40

*5

*2

4 Yellow continuous power supply 7 Red switched power supply

5 Blue power antenna (aerial) control 8 Black ground (earth)

6 Orange/White switched illumination power supply

*5

*1

*2

*3

*4

*5

*6

*4

*6

*1 from car antenna (aerial)

Auxiliary equipment such as portable DVD player (not supplied)

2 3

Connection diagram

A To AMP REMOTE IN of an optional power amplifi erThis connection is only for amplifi ers. Connecting any other system may damage the unit.

B To the interface cable of a car telephone

WarningIf you have a power antenna (aerial) without a relay box, connecting this unit with the supplied power supply lead

may damage the antenna (aerial).3

Notes on the control and power supply leads• The power antenna (aerial) control lead (blue) supplies +12 V

DC when you turn on the tuner, or when you activate the AF (Alternative Frequency) or TA (Traffi c Announcement) function.

• When your car has built-in FM/MW/LW antenna (aerial) in the rear/side glass, connect the power antenna (aerial) control lead (blue) or the accessory power input lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer.

• A power antenna (aerial) without a relay box cannot be used with this unit.

Memory hold connectionWhen the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off.

Notes on speaker connection• Before connecting the speakers, turn the unit off.• Use speakers with an impedance of 4 to 8 ohms, and with

adequate power handling capacities to avoid its damage.• Do not connect the speaker terminals to the car chassis, or

connect the terminals of the right speakers with those of the left speaker.

• Do not connect the ground (earth) lead of this unit to the negative (–) terminal of the speaker.

• Do not attempt to connect the speakers in parallel.• Connect only passive speakers. Connecting active speakers

(with built-in amplifi ers) to the speaker terminals may damage the unit.

• To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative (–) lead for the right and left speakers.

• Do not connect the unit’s speaker leads to each other.

Note on connectionIf speaker and amplifi er are not connected correctly, “FAILURE” appears in the display. In this case, make sure the speaker and amplifi er are connected correctly.

10

CDX-GT610U/GT616U/GT617UESECTION 2

DISASSEMBLY

Note: This set can be disassemble according to the following sequence.

2-1. SUB PANEL ASSY(Page 11)

2-2. CD MECHANISM BLOCK(Page 11)

SET

2-3. MAIN BOARD(Page 12)

2-5. CHASSIS (T) SUB ASSY(Page 13)

2-6. ROLLER ARM ASSY(Page 13)

2-7. CHASSIS (OP) ASSY(Page 14)

2-4. SERVO BOARD(Page 12)

1. CHUCKING ARM SUB ASSY(SUPPLEMENT-1 Page 1)

2. SLED MOTOR ASSY(SUPPLEMENT-1 Page 2)

3. OPTICAL PICK-UP SECTION(SUPPLEMENT-1 Page 3)

4. OPTICAL PICK-UP(SUPPLEMENT-1 Page 3)

Ver. 1.1

11


2-2. CD MECHANISM BLOCK

Note: Follow the disassembly procedure in the numerical order given.

2-1. SUB PANEL ASSY

2 two claws

3 two claws

6 sub panel assy

1 two screws (+PTT 2.6 × 6)

5 flexible flat cable (20 core)(CN802)

4 CN203 (3P)

4 CN350

3

1 screw(+PTT 2.6 × 6)

2 screw(+PTT 2.6 × 6)

5 two screws(+PTT 2.6 × 4)

6 bracket (CD)7 CD mechanism block

12


2-4. SERVO BOARD

2-3. MAIN BOARD

qd MAIN board

insulating sheet3


5 screw(+PTT 2.6 × 8)

1 three ground point screws(+PTT 2.6 × 6)

0 two screws(+P 2.6 × 8)

qa screw(+PTT 2.6 × 10)

qs heat sink

6 cord (RCA)

8 two screws(+P 2.6 × 8)


7 screw(+PTT 2.6 × 10)

4 CN410 (3P)

5 SERVO board

SERVO board

claw

claw

3 toothed lock screw(M 1.7 × 2.5)

2 toothed lock screw(M 1.7 × 2.5)

1 Remove the eleven solders.

GRYYELBLU

ORGREDBLKREDWHT

BLKREDWHT

4 optical pick-up (16 core)(CN1)

13


2-6. ROLLER ARM ASSY

2-5. CHASSIS (T) SUB ASSY

4 chassis (T) sub assy

3 claw

1 two precision screws(+P 1.7 × 2.2)

2 two precision screws(+P 1.7 × 2.2)

3 washer

4 gear (RA1)

5 roller arm assy

1 spring (RAL)

2 spring (RAR)

14


2-7. CHASSIS (OP) ASSY

7 coil spring (damper) (natural)

8 coil spring (damper) (green)

6 chassis (OP) assy

5

1 tension spring (KF)

2 gear (LE1)

3 lever (D)

4 slider (R)

Ver. 1.1

15


DIAGNOSIS FUNCTION

Description of the Diagnostics function:

1. Setting the Diag display modeWith the power off, press the [4] button, [5] button, and [4] buttonon the set body or the remote control (for more than 2 seconds)in turn.

2. Canceling the Diag display modeDuring the Diag function mode, press the [OFF] button.

3. Initial display in the Diag display mode.Just when the Diag mode is entered, “reset count” is displayed.The display mode is switched by each rotation of SEEK +/M > or SEEK – /. m keys.

4. Contents of each display mode4-1. Reset count display mode

4-2. Reset count by watchdog timer display mode

4-3. Number of connected units display mode

The display mode is switched by each rotation of [2/GP/ALBM+] or[1/GP/ALBM--] keys during the number of connected units displaymode.

4-4. Operating hours display mode

Reset count (in hexadecimal format)

Diag code01: Reset count

0 1 X X

Reset count (in hexadecimal format)

Diag code 02: Number of resets by watchdog timer

0 2 X X

Show the number of connected units for CD-C, MD-C and XM respectively from the rightmost (in hexadecimal format).

Recency of information1-3: 1 represents the latest.

Diag code03: Number of connected unit.

0 3 1 X X X

No. of connected units history 1 (latest) display

No. of connected units history 3 display

No. of connected units history 2 display

0 3 1 X X X

0 3 2 X X X

0 3 3 X X X

Operating hours (in hexadecimal format)

Diag code04: Operating hours

0 4 X X X X

Reset count display

OFFSET/FAILURE error display

CD error information display

Operating hours display

Number of connected units display

Reset count by watchdog timer display

0 1 X X

0 2 X X

0 3 1 X X X

0 4 X X X X

0 5 1 X X

0 6 1 X X X X X

USB error information display

0 7 1 X X

16


4-5. CD error information display mode4-5-1. Error description

4-5-2. Disc type and operating hours

The display mode is switched by each rotation of [2/GP/ALBM+] or[1/GP/ALBM--] keys during the CD error information display mode.

4-6. OFFSET/FAILURE error display mode

The display mode is switched by each rotation of [2/GP/ALBM+] or[1/GP/ALBM--] keys during the OFFSET/FAILURE error displaymode.

Error description (in hexadecimal format)


Diag code05: CD error information

0 5 1 X X

Operating hours


Diag code05: CD error information

0 5 1 X X X X

CD error info history 1 (latest)Error description plus error details display

CD error info history 3Disc type plus operating hours display

CD error info history 3Error description plus error details display

CD error info history 2Disc type plus operating hours display

CD error info history 2Error description plus error details display

CD error info history 1 (latest)Disc type plus operating hours display

0 5 1 X X X X

0 5 2 X X

0 5 2 X X X X

0 5 3 X X

0 5 3 X X X X

0 5 1 X X

Operating hours


Diag code06: OFFSET/FAILURE

Error description (0: OFFSET, 1: FAILURE)

0 6 1 X X X X X

OFFSET/FAILURE error history 1 (latest) display

OFFSET/FAILURE error history 3 display

OFFSET/FAILURE error history 2 display

0 6 2 X X X X X

0 6 3 X X X X X

0 6 1 X X X X X

Error informationIndication Description

1X SERVO ERROR3X LOADING ERROR4X TRACK JUMP5X TEXT ERRORFX MECHA ERROR

Disc typeIndication Disc type

0 MP31 WMA2 AAC3 ATRAC8 CD/DAF UNKNOWN

4-7. USB error information display mode4-7-1. Error description

Error description (in hexadecimal format)


Diag code07: USB error information

0 7 1 X X

Error informationIndication Description

15 DEVICE ERROR

17FILE ERROR(NO MUSIC)

1E POWER ON ERROR1F BOOT ERROR

3AINVALID EJECTERROR

43 READ ERROR

44INVALIDFORMAT FILE

FANOT SUPPORTDEVICE

FBHUB NOTSUPPORT

17


4-7-2. Disc type and operating hours The display mode is switched by each rotation of [2/GP/ALBM+] or[1/GP/ALBM--] keys during the CD error information display mode.

USB error info history 1 (latest)Error description plus error details display

USB error info history 3Disc type plus operating hours display

USB error info history 3Error description plus error details display



USB error info history 1 (latest)Disc type plus operating hours display

0 7 1 X X X X

0 7 2 X X

0 7 2 X X X X

0 7 3 X X

0 7 3 X X X X

0 7 1 X X





0 7 4 X X

0 7 4 X X X X

0 7 5 X X

0 7 5 X X X X

Operating hours


Diag code07: USB error information

0 7 1 X X X X

18


MEMO

19 19CDX-GT610U/GT616U/GT617UE


4-1. BLOCK DIAGRAM — MAIN SECTION —

SECTION 4DIAGRAMS

1 ANT

SCLSDA

CDMONCDON

ELECTRONIC VOLUMEIC401

J1(ANTENNA)

TU1(TUNER UNIT)

I2C BUS CONTROLLED POWER AMP/MULTIPLE VOLTAGE REGULATOR

IC300

SYSTEM CONTROLIC501 (1/2)

CN300

CN410

(REAR)

(FRONT)

(REAR)

(FRONT)

BATT

6 CD-LCH5 CD-RCH

6S-METER7TU MUTE

16E2P SCL17E2P SDA

39 VSM

5QUALITY

9RDS OUT

38 QUALITY8MUTE CON 53 TU ATTIN

56 DAVN

BU+3.3V

30 RDS ON

99 CDM ON98 CDON93 Z MUTE

11VDD+5V

4L-CH3R-CH

BU+3.3V

10VCC

12 TUATT

13 NSMASK

25 EEP CKO24 EEP SIO

CD ONCDM ON

CD LCD R

4 TU-LCH3 TU-RCH

CD-RCH

A ATT

TU-RCH

AUDIO+8.3V

AUDIO+8.3V

19SOUT18DATA

53

OUT FL+OUT FL–

97

OUT RL+OUT RL–

2927

AMP REM

R-CH

ANT REM

37REG1

35VP20VP16VP2

REG23133

REG3REG4

34REG5

28MUTE

2 SDA

AUDIO+8.3VBU+5VSERVO+3.3VMECHA+6VPANEL+B

4 SCL

SDASCL

16 BEEP22 STB25 DIAG

15

13

7

10

12

11

16

19

2

4

3

56

2930

SCLSDA

SCL

SA CLKSA DATA

SA IN

SDA

SCLSDA

986

VOLATTATT

33I2C CKO34I2C SIO

87

BUIN

73TESTIN

12 IN RR FL+FL–

RL+RL–

FR+FR–RR+RR–

AMP-REMANT-REM

ACC

TEST

17CLK

MUTEQ470

AUDIO OUTREAR

MUTE CONTROLSWITCH

Q491,492

60

UNISI54

UNISO

58

UNISCK

59

BUSON

88SYSRST

12

B/U-C11

DATA OUT10

DATA IN8

CLK IN

9

BUS IN

13 RST

RESET

3

56

8

423

1

BATT

CLK 4DATA I/O

1BUS ON

2RSTSY

SRST

72ACCIN ACCESSORY CHECKQ702

BATTBATT

OVER VOLTAGECHECKQ605

BUS INTERFACEIC601

MUTEQ430

MUTEQ426

MUTE CONTROLSWITCH

Q423

MUTEQ440

SA INSA DATA

44SA IN32SA DATA

SA CLK45SA CKO

D491

FU601

R-CH2324

OUTR2OUTR1

R-CH

L

R

J451 (2/2)

AUDIO OUTFRONTR-CH

2526

OUTF2OUTF1

R-CH

L

R

SUBOUT

21OUTS2 L

R

BUSCONTROL IN

D400

D602

DISPLAY SECTIONA

TH400

CNJ4007

BATT

TUNER+5VREGQ3

NOISE MASKSWITCH

Q1

RDS+3.3VSWITCH

Q50

RDS MODULATORIC50

15E2PVDD

13TU-SCL14TU-SDA

BU+5VBU+3.3V

REGIC502

11 IN RF

TEL ATT74TELATT TELEPHONE ATTENATION CHECKQ701

14ILL75ILLUIN

8DIAG26AMPSTB

7BEEP

BUSAUDIO

IN BUS-RCH

L

R

J451 (1/2)

Q471

9 BUS-LCH7 BUS-RCHBUS-RCH

CD-RCH

TU-RCH

ZMUTE

91 WAKE UPWAKE UP

89 EJECT OK SW

17 AUX SW

EJECT OK

27 MC RXMC RX

28 MC TXMC TX

Z MUTE

SYS RST

MECHA+6VBU+3.3V

SERVO+3.3V

BU IN

RXD

TXD

DR+6V

BU+3.3V

A+3.3V

D+3.3V

CDONCDMONZMUTE

WAKE UP WAKE UP

SYSRSTEJECT OK EJECT OK

BU IN

MC TX

MC RX

CDMECHANISM

UNIT(MG-101U)

(1/2)

6

11SCL

15INTN

16 MPX

XTO

XTI

12SDA

SCLSDA

1VDDA7VDDD

10

9

X508.664MHz

BUIN

ILLUMINATION CHECKQ703

30

BATT

• Signal Path• R-CH is omitted due to same as L-CH.

J : CD PLAY

K : FM

L : BUS

f : MW/LW

K K

K K

K K

K

K

K

K

K

K

K

K

K

J J

K

L L

KfK

(Page 20)

2020CDX-GT610U/GT616U/GT617UE


4-2. BLOCK DIAGRAM — DISPLAY SECTION —

RESETMAIN

SECTION A

KEY ACKNOWLEDGESWITCH

Q501

83

82

41

192018

40

52

76

64

SYSTEM CONTROLIC501 (2/2)

USB CONTROLIC803

DC-DC CONVERTERIC802

SHIFTCONTROLSWITCH

Q801

FL900FLUORESCENT

INDICATOR TUBE

KEYIN0

CLKCS

FL SOFL SCK

FL CS

28

27

35

34

26

GRID1

GRID2

GRID3

331G

13RESET

32Q1

31Q2

F+

F–

KEYIN1

47 RE-IN048 RE-IN1

71 RC IN143 RC IN0

KEYACK

AD ON

5 NOSE SW

SIRCS

77 RESET

46 DOOR IND

FL VH+12V

OSCOUT

OSCIN

65FL12V ON

X50018.432MHz

1112

103G

D501

39•

38

2•1

2G

DIO

PANEL+B

BU+3.3V

BU+5V

KEY MATRIX

80

79XOUT

XINX501

32.768kHz

10FSW IN

21USB OVER

70DOOR SW

3 2C

22USB ON

67DD ON

66FSW OUT

LSW901,S201,902–904,906–917

(VOLUME)

PUSH SELECTRE901

ROTARYENCODER

REMOTE CONTROLSIGNAL RECEIVER

IC971

S102(NOSE DET)

RESETIC602

PANEL+3.3V

FL VH+12V

PANEL+3.3V

BATT

PANEL+B

LED952–954,956–967,991–994,LSW901

LED902–904,906–917,941–944,LSW901

IN V–BUSOUT

4 EN5 OC

1

7

6 5

3

22•3

6•7•8

FL DRIVEQ991

FL DRIVEQ992

LED DRIVEQ941

LED DRIVEQ942

FL DRIVEQ993

7VH

8VDD(3.3V)

PANEL+3.3VREG

IC804

S103RESET

LED202Z

LED201

CDINDICATOR

D982

D998

V-BUS

USB SELECT SWITCHIC980

Q503

S918

CDMECHANISM

UNIT(MG-101U)

(2/2)

D997

FL +12VREG

IC801

SWBATT

INV

FB

VIN

EN

RT

D802

7 1C

2 1B5 2A

62B

USB D+USB D–

11A

J370(REMOTE IN)

DOOR INDICATORCONTROL SWITCH

Q589,590OPEN/CLOSE

5

4321

J11

J11

(Page 19)



• Waveforms

— MAIN Board —

• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR PRINTED WIRINGBOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note isprinted in each block.)

For schematic diagrams.Note:• All capacitors are in µF unless otherwise noted. (p: pF)

50 WV or less are not indicated except for electrolyticsand tantalums.

• All resistors are in Ω and 1/4 W or less unless otherwise

specified.• f : internal component.• C : panel designation.

For printed wiring boards.Note:• X : parts extracted from the component side.• Y : parts extracted from the conductor side.• a : Through hole.• : Pattern from the side which enables seeing.(The other layers' patterns are not indicated.)

• A : B+ Line.• B : B– Line.• H : adjustment for repair.• Voltages and waveforms are dc with respect to ground

under no-signal (detuned) conditions. no mark : FM

( ) : MW/LW< > : CD PLAY

∗ : Impossible to measure• Voltages are taken with a VOM (Input impedance 10 MΩ).

Voltage variations may be noted due to normal productiontolerances.

• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal productiontolerances.

• Circled numbers refer to waveforms.• Signal path.J : CD PLAYF : FMf : MW/LWL : BUS

Caution:Pattern face side: Parts on the pattern face side seen from the(Side B) pattern face are indicated.Parts face side: Parts on the parts face side seen from the(Side A) parts face are indicated.

Q

C

These are omitted

EB

EThese are omitted

CB

CThese are omitted

BE

Note: The components identified by mark 0 or dotted linewith mark 0 are critical for safety.Replace only with part number specified.

1.1 Vp-p

8.664 MHz

3 IC50 9 (XTI)

0.7 Vp-p

32.768 kHz

1 IC501 i; (XIN)

0.9 Vp-p

18.432 MHz

2 IC501 is (OSC IN)

0.2 V/DIV, 20 µsec/DIV

0.5 V/DIV, 0.1 µsec/DIV

0.5 V/DIV, 0.1 µsec/DIV



: Uses unleaded solder.4-3. PRINTED WIRING BOARD — MAIN SECTION —

1

A

B

C

D

E

F

G

H

I

J

2 3 4 5 6 7 8 9 10 11 12 13 14

L RJ1

(ANTENNA) L R

-1 -2 -3 -4

AUDIO OUTREAR

L R L R

-5 -6 1 2 3

AUDIO OUTFRONT

CN410(SUB OUT)

BUSAUDIO IN

CDMECHANISM

UNIT(MG-101U)

(1/2)

8 73 2 1

6 5 4

123

5

4

1

7

X500

(CHASSIS)

(CHASSIS)

S103RESET

S102(NOSE DET)

1-872-074- 11

FU601

CN2

BATT

C414C413

C432 C452 C442 C422

R432 R452 R442 R422

Q44

0

Q42

0

C423

C443 Q46

0

Q470

R470

R460

R440

C454

R481

R480

R482

R483

C482

C483

C484

R2

R3

R4

R5 R1R8

R9Q1

D2

C7R10

Q3

C3

C9

R12

R13

R6

R7

C8

C301

YEL+B 14.4V

YEL

+B 14.4V

C323C324

C304C305C307

C320 C462

C313

C315

R70

2

R703 R704

D705

C902

C901

C704

L301

L302

L303

D606

D605

D60

2

Q605

R60

3

R60

4

R611

D603

D604

R61

0

R606

R607

R706

D701

D704

D70

3

R708

R70

7

Q702

C415

C402

R351

FB408

FB40

7

FB406

FB405

FB401

FB402

FB403

C412

R402

R401

C419C418

R71

1

R712

Q703

IC60

1

C601

R543

IC602

R52

2

R53

1

R53

2 R53

4 R60

1

R602

R536

C516

C515

C506

R370 R546R529

R530 R528R54

7

D502

R541

R526R525

C507

C508

R54

0

C509

R51

6

R54

8R

549

R54

5

R302C319

C318

R301

R509

R510

C504

R51

9

R520

D50

1

R542

C56 C57

R11L2

L3

IC50

R14

C58

R55

C50

C51

C52

C53

C54

C55

R52

R53 R54

C60

Q50

R58

C502

IC502

C325

D491

R491

Q501

R52

3

R52

4

R57

L1

L500

L4

R55

3

C14

C62

D903

R500

JC50

1 JC50

3

JC491JC490

JC30

2

JC300 JC301

JC3

JC600

JC50

6

JC998

JC350

C519

R527

R53

3

R420

R471

R53

9

R521

C513

Q701

C410

JC999

C705

C523

JC90

SUB BOARD CN202

C114

C110

C108

C103

D10

3

C104

D101

R55

5

R55

6

R558

R53

7

JC304

R411

C411

R46

1

R559

JC32

D11

4

D11

5

R418

Q589

Q590

JC305

Q43

0

R416

Q492Q491

D400

R56

3

C472

R433

R45

4

R453

R51

3

C470

JC52

4R

561

R56

2

R503R504

R505R506

R455

IC40

1

Q47

1

R47

4

R57

1

C327

C328

R419

R417

R554 R484

R557

R570

IC501

FMB3

FMB4

JC511

JC512

R572

C998

R60

0

C465

C466

R51

4

R517

R51

5

R518

D118

IC802

IC801

C809

C810

C811

C812

C814

C816

C819R801

R802R803

R804R805

R806

R80

8

FB80

1

R809

FB802

FB803

FB80

4

Q801

R81

0

R81

1

D802

D801

JC50

4

JC51

8

JC519

JC50

8

D119 JC53

D120

JC602

JC400

JC80

6

R701

R502

R371C512C511

C510

IC804

IC803

JC494

JC49

2

C447

C446R

431

R421

R441

JC9

JC522

JC80

4

R512

C817R812

D10

4

D10

5

D10

6

D10

7

D108D109

D110

JC603

JC52

3

R709

D10

2

R55

1

JC51

4

JC51

5

JC51

6

C821

JC51

0

C602

R605

R830

C830

R573

C417

C109

JC49

3

D471

R53

5

R424

R42

5JC42

9

Q424

R423

C312

Q426

Q423

GT617UE

GT617UE

GT617UE

GT61OU/GT616U

GT61OU/GT616U

GT61OU/GT616U

C360

C361

R57

4

C362

R813

C309

JC997

JC49

5 FB404

C303

C471

C2

C5

C310

C308

C306

D30

8D30

5

D31

0

D30

2

D30

1

D304

D303

D60

7C701

L300

CNJ400

J370(REMOTE IN)

CNJ400(BUS CONTROL IN)

CN300

TH400

C401

C405

C703

X500

X501

X50

C61

S103

TU1(TUNER UNIT)

CN350

R710

D30

9

D31

1

D31

2

C1

C480

C481

S102

R70

5

J451

D30

7

D30

6

C487

C461

C485

C505

IC300

JW1

JW2

JW3

JW5

JW6JW7

JW8

JW9

JW10

JW11

JW12

JW13

JW17

JW21

JW22

JW23

JW24

JW25

JW26

JW27

JW28

JW29

JW30

JW31

JW32

JW44

JW45 C600

JW52

JW55

JW56

JW57

JW58

JW59

JW60

JW61

JW65

JW66

JW67

JW68

JW69

JW72

JW73

JW80

JW81

JW82

JW83

JW84

JW85

JW86

JW87

JW88

JW89

JW90

JW92

JW94

JW95

JW96

JW97

JW98

JW99

JW10

3

JW10

4

JW10

5

JW10

9

JW110

JW111

JW112

JW11

3

JW11

4

JW115

JW11

7

JW11

8

JW12

4

JW12

7

JW12

8

JW13

1

JW13

2

JW12

9

L802

L803

C803

C805

C802

JW13

4

JW13

5JW

136

JW13

7

JW13

8

JW13

9JW14

0

JW14

1

JW14

3

JW15

0

JW15

4

JW15

3

JW152

JW74

CN802

JW64

JW62

JW63

JW38

JW34

JW35

JW36

JW33

JW39

JW40

JW41 JW37

C363

C364

C431

C441

C421

JW14

8

JW10

1

JW13

3

JW10

8

JW14

2

JW78

JW79

JW10

2

JW10

7

JW76

JW50

JW49

JW46

JW47

JW12

5 JW11

9JW

120

JW12

1

JW12

2

JW12

3

C806

JW15

6

JW14

JW15

JW16

JW18

JW19

JW15

7

JW43

JW158

JW160

C804

JW51

JW20

JW14

7

C702

C501

C403

C316

C503

C314

C491

C317

L101

JW13

0

JW10

0

JW149

JW151

JW54

JW77

JW75

L801

JW15

5

CN410

C801

C822

C429

C430

JW53

JW4

D702

R450

(Page 26)

D2 F-2D101 I-2D102 I-2D103 J-3D104 J-3D105 J-3D106 J-3D107 J-3D108 J-2D109 J-2D110 I-2D114 J-2D115 J-2D118 I-3D119 I-4D120 J-4D301 D-8D302 D-8D303 D-9D304 C-9D305 D-6D306 C-6D307 C-6D308 D-6D309 D-7D310 D-6D311 D-7D312 D-7D400 H-8D471 B-3D491 E-5D501 I-6D502 I-6D602 F-10D603 F-10D604 F-10D605 B-10D606 C-10D607 C-10D701 C-8D702 G-10

• Semiconductor LocationRef. No. Location Ref. No. Location

D703 D-8D704 F-9D705 G-9D801 I-10D802 I-6D903 C-9

IC50 H-2IC300 B-5IC401 E-3IC501 H-6IC502 E-6IC601 H-10IC602 I-8IC801 I-7IC802 I-10IC803 J-5IC804 I-4

Q1 E-2Q3 F-2Q50 H-1Q420 C-4Q423 F-7Q424 E-6Q426 E-6Q430 C-3Q440 C-3Q460 C-4Q470 C-4Q471 B-2Q491 E-5Q492 E-5Q501 I-6Q589 I-2Q590 I-2Q605 F-10Q701 D-8Q702 G-10Q703 G-9Q801 I-10



4-4. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) — • Refer to page 30 for IC Block Diagrams.

IC B/D

C701

D303 D304

D30

1

D30

2

C303

C600

R610

D606

C306

D305D306D307D308D309D310D311D312

C317

R301

R302

R604 R603

R706 R708

R707

R703

R704

D705 R711

R712C703

Q492

C491

R491 D491

C501

R600

JC999

R605

Q491

C602

JC603

C601

JC602

C901C902

C705

C319

C318

JC504

JC495

C472 C462

C465C466

C324

C304

C323

C301JC301JC300 C305

C307C309

C325 C502

C704

JC510

R611

D607

C320

C310

C312

C313

C314

C315

C316

IC502

JC302

C308

R601R602

CN300

FU601

R710

R701

R709R705

C702

R606

R607

L303

L301

L302

IC601

L300

Q605TH400

CNJ400

J370

JW43

IC300

D701

D702

D703

R702

D903

D704

D603 D602

D605D604

Q703

Q701

Q702

(Page 25)

(Page 24)



4-5. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) —• Refer to page 21 for Waveforms.• Refer to page 30 for IC Block Diagrams.

(Page 23)

(Page 25)

IC B/DIC B/D

Q3

R441 R421 R431

C441 C421 C431

X50

R52

R53

C363

C364

R3

R10

C1

C5

R58

Q440 Q420 Q430

R11

R483

R481

R440

R460

R470

R420

Q460Q470

C471

R471 R461

C461

L4

CN410

R432R411

R452R422R442

R484

R418 R416

Q589

CN802

C487

JC304

L101

JW142

Q590

R542

JC998

C14

C484

JC522

JC491 JC305

C443 C447

C423 C446

C411

C442 C422 C452 C432 C413 C414

JC490

C328

C327C55

C54

C52

C51

C50

C58

L2 L3

C8

C9

C7

C103

C104

C114

C108

C109

C110

JC9

C57

C56

C485

JC400

C454

R454

R453

R455

C362

C361

C360

JC494

JC492

C481

R482

R480

C480

C483

C482

JC493

R419 R417

R474

C470

R55

C53C61

C60

R14 C62

JC806

JC32

C2

C3

JC3

R9

R8

R2 R1

R5

R4

IC50

TU1

R450

J451

Q471

Q1

J1

JW25

JW151

JW125 JW158

JW149

Q50

JW26D471

IC401

R433

R57

R7

R6

L1

R13R12

R54

D118

D11

0

D10

9

D10

8

D11

4

D10

7

D10

6

D10

5

D10

1

D10

4

D11

9

D10

3

5120

D10

2

D11

5

D2

(Page 27)



4-6. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) —

• Refer to page 21 for Waveforms.• Refer to page 30 for IC Block Diagrams.• Refer to page 31 for IC Pin Description of IC501.

(Page 23) (Page 24)

IC B/D

C401

C405

R401

R402

D50

2

D400

C503

R548 R549

JC600

JC50

6

JC512

JC511

R55

4

R521

R563

R513

C802

R802

R803

R805

R809

R808

R810

R811

C801

C804

C803

R801

C805

JW136

R806 R812

C806

JC51

4

JC51

5

JC51

6

R804

R830

C830

R424

Q424

R425

Q426

C429

C430

R423

R813

C822

JC997

R50

2

R50

5

R50

3

R523

R524

R53

0

R51

4

R51

5

R51

6

R518R517

R51

0

R50

9

R526

R53

1

R53

2

R53

3

R53

4

R527

R539

R540

R543

R54

5

R54

6

FB405

FB403FB406

C998

C523

R556

R555

R557

R558

R570

FB802

FB803

R57

2

R57

3

FB801

R51

2

R57

4

R50

4

R50

6

C417

FB404

JC350

JC804

C819

C809 C810 C821 C811

C814

C817

C816

C402

C410

FB401C412 JC429

C515

C516

C506

JC519

JC523

C504

JC524

JC90

JC501C507

JC503

C519

JC53

R551

R553

R536

C505L500 R537

R500

R351

C415FB407 C419

C418

C403

FB402

R571

R559

JC51

8

C512

C511

C510

C513 R371 JC508

R519

R520

R522

C509

C508

R547

R370

R529

R528

R525

R535

R541

IC802

IC804

C812

Q801

JW129 JW128

S103

Q501

JW99

JW98

S102

CN350JW49

Q423

FB804

X501

FB408

IC801

D802

L802 L803 IC803

IC602

D501

X500

IC501

JW79

JW78

R561

R562

L801

D80

1



4-7. PRINTED WIRING BOARD — SUB SECTION — : Uses unleaded solder.

1

A

B

C

D

E

F

G

H

I

J

2 3 4 5 6 7 8 9 10 11 12

1-872-098-

1-872-098-

MAIN BOARD CN802

KEY BOARD CN901

A

B

(11)

11

(11)

11

FMA3

FMA4

R201

R202

S201

LED202

CN201

LED201

LED201(CD INDICATOR)

LED202,S201Z

R203

R204

C202

R205

D203

D204CN203

CDMECHANISM

UNIT(MG-101U)

(2/2)

CN202

CN101

3

11 20

(Page 28)(Page 22)



4-8. SCHEMATIC DIAGRAM — SUB SECTION —

(GT610U/GT616U)(GT617UE)

*1 *1

*1

CN201

CN203

R203R204

C202

R205

S201

R201 R202

CN202

LED202

D204 D203

LED201

LED201,202SML-310VTT86SML-310PTT86

(Page 24)(Page 29)

Ver. 1.1


CDX-GT610U/GT616U/GT617UE4-9. PRINTED WIRING BOARD — KEY SECTION — : Uses unleaded solder.

1

A

B

C

D

E

F

G

H

2 3 4 5 6 7 8 9 10 11 12 13

1-872-099-

1-872-099-

LED902,952,S902

SOURCE

M >

SEEK+

LED941-944,991-994(RING ILLUMINATION)

LSW901

SEEK–

OFF

EQ3

LED908,958,S908

LED907,957,S907

DSO

LED906,956,S906

DSPL 1/GP/ALBM– 2/GP/ALBM+ 5/BBE MP 6/PAUSE AF/TA

IC971

PTY

MODE

LED917,967,S917

LED903,953,S903

LED904,954,S904

LED916,966,S916

LED915,965,S915

LED914,964,S914

LED913,963,S913

LED912,962,S912

LED911,961,S911

LED909,959,S909

LED910,960,S910

3/REP 4/SHUF

BSUB BOARD CN201

145

8

GT617UE

GT610U/GT616U

(11)

11

(GT610U/GT616U)

(21)

21

(GT617UE)

(11)

11

(GT610U/GT616U)

(21)

21

(GT617UE)

PUSH SELECT(VOLUME)

RE901

S908

S907S9

06

S902

S903

S904

S909S910S912S913S914 S911S915S917

LED

909

LED

910LE

D91

1

LED

912

LED

913

LED

915LE

D91

6

LED

917

LED

908

LED

907

LED

906

LED

943

LED

903

LED

904

LED944

LED

959

LED960

LED

961

LED

962

LED

963

LED

964

LED

965

LED

966

LED

967 LE

D95

4

LED

953

LED

952

LED

958

LED

957

LED

956

LED

993

LED994

IC971

1 2

4 3

LED

991

LED992

LED

941

LED942

LSW

901

S916

LED

902

LED

914

R939

R94

0

R941

R94

2

R95

9

Q50

3

D99

7

D99

6

D904

FB97

1

R93

6

R94

8R

950

R93

3

R93

5

R93

4 R947

3 5 4

2 1

39 1

FL900FLUORESCENT INDICATOR YUBE

R94

9

R93

7

R93

8

R945

R946R944

R973R971R972

C971 D97

1

R906

R943

R907

R908

R992Q991

D982 R994

Q993Q

992

R99

5 R99

6

R963

R962

R95

3

R958

R95

5

R957

R921

R954

R951

R952

R956

R916 R915R922

R923

R924

R914

R927

R993 R98

9

R98

8

R99

0R

966

C932

D986

R98

6

Q941

R925

Q942

R913

R98

5

R984

R981

C992

R98

2

R98

3

R93

2R926

R92

8

R931

R93

0R929

R911

R91

0 R90

9

D902

D984

D98

1

D98

3

R987

C920

D985

C991

R902

R904R905

R912

R991

R903

CN901

R967

IC980

R901

R968

J11

J11

LF99

0R965

R964

C921

D90

3

D976D973

D992

D991

D98

9

D990

D993

D978

D979

R96

9 S918FB991

D93

1

D99

8

RE901

5

4

3

2

S918(OPEN/CLOSE)

(Page 26)

D984 F-9D985 F-8D986 G-8D989 G-9D990 G-9D991 F-9D992 F-9D993 G-11D996 A-12D997 B-13D998 G-13

Ref. No. Location

D902 G-11D903 E-12D904 C-12D931 G-8D971 E-3D973 F-11D976 F-11D978 F-12D979 F-12D981 F-9D982 D-5D983 G-9

• Semiconductor LocationRef. No. Location

IC971 D-3IC980 F-12

LED902 B-5LED903 B-5LED904 C-5LED906 C-2LED907 B-2LED908 B-2LED909 D-11LED910 D-10LED911 D-10

Ref. No. Location Ref. No. Location

LED912 D-9LED913 D-8LED914 D-7LED915 D-6LED916 D-5LED917 D-4LED941 B-3LED942 B-4LED943 C-3LED944 B-3LED952 B-5LED953 B-5

LED954 C-5LED956 C-2LED957 B-2LED958 B-2LED959 D-11LED960 D-11LED961 D-10LED962 D-9LED963 D-8LED964 D-7LED965 D-6LED966 D-5

LED967 D-4LED991 B-3LED992 B-4LED993 C-3LED994 B-3

Q503 B-13Q941 F-5Q942 F-8Q991 G-7Q992 G-7Q993 G-7

Ref. No. Location Ref. No. Location

Ver. 1.1



4-10. SCHEMATIC DIAGRAM — KEY SECTION —

GT610U/GT616U

GT617UE

R985

R986

R988

R990

R984

R972

R962

R963

R915

R908

R914

R907R906

R913R912

R904

R911

R903R902

R910R909 R916

FB971

R982

FB991R987

R905

R967

D981

D984

D902D903

R968

D998

D983

R971

R973

R969

D993D996

D986

D985

D989D990

D992D991

C921

R983

D904

R964

R965

R981

S918

R959

S908S907S906

S917S916S915S914S913S912S911S910

S904S903S902LSW901(1/2)

S909

R901

C920

J11

R921 R922

R923 R924

R925 R926

R927 R928

R929 R930

R931 R932

R933 R934

R935 R936

R937 R938

R943 R944

R945 R946

R951

R953

R952

R954

R939 R940

R941 R942

R947

R949

R948

R950

R955 R956

R957 R958

C971

C932

IC971

R993

Q99

2

Q99

3

Q99

1

C991 C992

R996R994

R966D931

R992R991

D971

LSW901(2/2)

RE901

D978 D979

Q503

Q941Q942

LED917

LED916

LED915

LED967

LED966

LED965

LED914

LED913

LED912

LED964

LED963

LED962

LED909

LED910

LED911

LED959

LED960

LED961

LED941

LED942

LED991

LED992

LED943

LED944

LED993

LED994

LED902

LED904

LED952

LED954

LED908

LED906

LED958

LED956

LED907

LED903

LED957

LED953

FL900D982

R989

D997

IC980

LF990

CN901

D973 D976

R995

(Page 27)

Ver. 1.1



• IC BLOCK DIAGRAMS

IC601 BA8271F-E2 (MAIN Board (1/3))

1

2

3

456

7 8

9

10

14

131211

BUS ONSWITCH

RESETSWITCH

BATTERYSWITCH

BUS ON

RST

BATT

CLKVREF

GND

VCC

RESETBUS ONCLK INBU IN

DATA IN

DATA OUT

DATA

IC401 BD3442FS-E2 (MAIN Board (2/3))

1

2

BUS-RCH

100k

100k

100k

100k

100k

100k

250k

250k

250k

BUS-LCH

TU-RCH 3

4TU-LCH

5CD-RCH

6CD-LCH

7AUX-RCH

8AUX-GND

9AUX-LCH

10DS3-L

11DS1-L

12DS2-L

13EBIAS

14DS2-R

15DS1-R

16DS3-R

26 OUT-FR

27 VCCVCC

VCC2

28 MUTE

29 SCL

30 SDA

31 GND

32 F2L

INPUTSELECTOR

VOLUME1/MUTE

VOLUME2

I2CBUS

LOGIC

TREBLE/BASS

/MIDDLE

SPECTRUMANALYZER

FADER

25 OUT-FL

24 OUT-RR

23 OUT-RL

FADER

FADER

22 SUBOUT-R

21

20

SUBOUT-L

19

ADJ

18

SAOUT

17

SADA

SACLK

FADER

FADER

LPF

EFFECT

INPUTGAIN

FADER

IC50 TDA7333013TR (MAIN Board (2/3))

VDDA

INTERPOLATOR

RAMBUFFER

&CONTROL

LOGIC

TEST LOGIC&

PIN MUX'S

I2C/SPI

INTERFACE

BAND PASSFILTER

SIGMA DELTACONVERTER

SINC4FILTER

REF3

REF2

REF1

VSS

VDDD

RESETN

TM

1

MPX16

CSNSDAOUT

RDSREG

3

INTN

MPX

SINC

4REG

SDAINSCKSPITESTREG

14

2

3

4

5

6

7

8

INTN15

SA_DATAOUT13SDA_DATAIN12SCL_CLK11

OSCILLATOR

XTO10

XTI9

RDSDEMODULATOR &

SYNCHRONIZATION

2

IC802 BD9778HFP (MAIN Board (3/3))

1 2 3 4 5

CURRENTLIMIT

PWMCOMPARATOR

ERRORAMP

L:OFFH:ON

VREF

VINTSD

OSC

VIN SW PB GND INV6

RT7

EN

VREFSOFTSTART

ON/OFF

LATCH

DRIVER

RESET

31


• IC PIN DESCRIPTIONIC501 MB90F046PF-G-102E1 (SYSTEM CONTROL) (CDX-GT610U/GT616U) (MAIN BOARD (3/3))IC501 MB90F046PF-G-104E1 (SYSTEM CONTROL) (CDX-GT617UE) (MAIN BOARD (3/3))

Pin No. Pin Name I/O Pin Description

1 AREASEL0 I Destination setting pin 0



4 B-OUTSEL I Black-out with/without discrimination signal input “H”: Black-out

5 NOSE SW I Front panel attachment detect signal input “L”: with panel

6 AAC SEL I AAC play setting signal input “H”: AAC

7 BEEP O Beep signal output to power amplifier

8 DIAG I Status signal input from power amplifier

9 VOLATT O Electronic volume attenuate control signal output

10 FSW IN I D/D converter oscillator frequency count signal input

11 VSS — Ground pin

12 TUATT O Tuner mute control signal output

13 NSMASK O Noise mask signal output

14 NCO O Not used. (Open)

15 ILLUMI SEL I Illumination voltage setting signal input


17 AUX SW O AUX change over signal output “L”: AUX, “H”: BUS IN

18 FL CS O Fluorescent indicator tube chip select signal output

19 FL SO O Fluorescent indicator tube serial data signal output

20 FL SCK O Fluorescent indicator tube serial clock signal output

21 USB OVR I Overcurrent detect signal input from USB power supply high side switch

22 USB ON O USB power supply high side switch control signal output

23 VCC5 — Power supply pin (+3.3 V)

24 EEP SIO I/O EEPROM bus serial data signal input/output

25 EEP CKO O EEPROM bus serial clock signal output

26 AMPSTB O Standby signal output to power amplifier

27 MC RX I Mechanism microcomputer comunication signal input RX

28 MC TX O Mechanism microcomputer comunication signal output TX


30 RDS ON O RDS (Radio Data System) on signal output Tuner on: “L”


32 SA DATA O Data signal output for electronic volume IC spectrum analyzer

33 I2C SCK O I2C bus serial clock signal output

34 I2C SIO I/O I2C bus serial data signal input/output

35 DAVDD — A/D converter power supply pin (+3.3 V)

36 AVRH — A/D converter external reference power supply pin (+3.3 V)

37 DAVSS — Ground pin

38 QUALITY I Noise detect signal input

39 VSM I S-meter voltage detect signal input

40 KEYIN1 I Key signal input 1

41 KEYIN0 I Key signal input 0

42 VSS — Ground pin

43 RCIN0 I Rotary commander key signal input

44 SA IN I Spectrum analyzer data signal input

45 SA CKO O Spectrum analyzer clock signal output

46 DOOR IND O Disc door indicator control signal output

47 RE IN0 I Rotary encoder signal input 0

48 RE IN1 I Rotary encoder signal input 1

49 MD0 I Operation mode setting pin (Connect to VDD.)

32


50 MD1 I Operation mode setting pin (Connect to VDD.)

51 MD2 I Operation mode setting pin (Connect to VSS.)

52 KEYACK I Key acknowledgment detect signal input

53 TU ATTIN I Tuner mute zero cross detect signal input

54 BUIN I Back-up power supply detect signal input


56 DAVN I RDS (Radio Data System) data block synchronized detect signal input


58 UNISI I SONY bus data signal input

59 UNISO O SONY bus data signal output

60 UNISCK O SONY bus clock signal output

61 to 63 NCO O Not used. (Open)

64 SIRCS I Remote control signal input

65 FL12V ON O 12V power supply control signal output for fluorescent indicator tube

66 FSW OUT O D/D converter oscillator frequency shift control signal output

67 DD ON O 3.3V D/D converter power on/off control signal output for fluorescent indicator tube

68 FLASH W IMemory mode change signal input Normally “H”: Single chip mode, after reset

“L”: flash write mode


70 DOOR SW I Front panel open/close detect switch signal input

71 RC IN1 I Rotary commander shift key signal input

72 ACC IN I Accessory power supply detect signal input

73 TESTIN I Test mode detect signal input

74 TELATT I Telephone attenuate detect signal input

75 ILLUIN I Illumination detect signal input “H”: Illumination off

76 AD ON O A/D converter power supply control signal output

77 RESET I CPU reset signal input


79 XOUT O Low speed operation clock signal output (32.768 kHz)

80 XIN I Low speed operation clock signal input (32.768 kHz)

81 VSS1 — Ground pin

82 OSCIN I High speed operation clock signal input (18.432 MHz)

83 OSCOUT O High speed operation clock signal output (18.432 MHz)

84 VCC3 — Power supply pin (+3.3 V)


86 ATT O Audio mute control signal output

87 BUSON O Bus on signal output

88 SYSRST O System reset signal output

89 EJECT OK SW O Eject OK signal output to CD mechanism unit


91 WAKE UP O Mechanism microcomputer wake up signal output


93 Z MUTE I Mute signal input


95 DEMO SEL I DEMO select signal input “H”: DEMO on, “L”: DEMO off

96 CYRIL SEL I Cyril correspondence discrimination signal input “L”: No correspondence


98 CD ON I CD mechanism servo power supply control request signal input

99 CDM ON I CD mechanism deck power supply control request signal input

100 OPEN MUTE O Not used. (Open)

Pin No. Pin Name I/O Pin Description

33


EXPLODED VIEWS

1 X-2149-741-1 LOCK ASSY2 3-246-441-01 BUTTON (EJECT)3 1-833-591-11 CABLE, FLEXIBLE FLAT (20 CORE)4 3-260-247-01 CUSHION (SUB PANEL)5 3-042-244-01 SCREW (T)

6 X-2149-726-1 PANEL ASSY, SUB7 X-3384-203-1 GEAR ASSY8 3-713-786-51 SCREW +P 2X39 3-376-464-11 SCREW (+PTT 2.6X6), GROUND POINT10 A-1217-699-A MAIN BOARD, COMPLETE (GT610U/GT616U)

10 A-1217-728-A MAIN BOARD, COMPLETE (GT617UE)

11 2-021-848-01 SHEET (TU), GROUND12 1-831-837-11 CORD (WITH CONNECTOR) (ISO) (POWER)13 1-833-887-11 CONNECTION CORD (RCA) (SUB OUT (MONO))14 3-264-798-01 CAPFU601 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A

TU1 A-3220-961-B TUNER UNIT (TUX-032)#1 7-685-792-09 SCREW +PTT 2.6X6 (S)#2 7-685-790-01 SCREW +PTT 2.6X4 (S)#3 7-685-793-09 SCREW +PTT 2.6X8 (S)#4 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT

#5 7-685-794-09 SCREW +PTT 2.6X10 (S)

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

NOTE:• The mechanical parts with no reference

number in the exploded views are not supplied.• Items marked “*” are not stocked since

they are seldom required for routine service.Some delay should be anticipatedwhen ordering these items.

• -XX and -X mean standardized parts, sothey may have some difference from theoriginal one.

• Color Indication of Appearance PartsExample :

KNOB, BALANCE (WHITE) ... (RED)

Parts Color Cabinet’s Color• Accessories are given in the last of this parts list.

5-1. MAIN SECTION

R R

The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

not supplied

not supplied(SUB board)

not supplied

FU601

not supplied

TU1

not supplied

not supplied

#1

#1

#1

#3#5

#4

#3

#5

#4

#5

#2

#1

MG-101U-188//Q

A

B

B

1

2

34

5

6

7

5

8

9

12

11

A

10

not supplied

13

14

#3

34


51 A-1217-701-A PANEL OVERALL ASSY, FRONT (GT610U)51 A-1217-705-A PANEL OVERALL ASSY, FRONT (GT616U)51 A-1217-730-A PANEL OVERALL ASSY, FRONT (GT617UE)52 3-264-712-01 SPRING (OPEN)53 X-2159-395-1 BUTTON ASSY (S) (GT610U)

53 X-2159-397-1 BUTTON ASSY (S) (GT616U/GT617UE)54 X-2159-394-1 PANEL (SV) ASSY, FRONT (GT610U)54 X-2159-396-1 PANEL (SV) ASSY, FRONT (GT616U)54 X-2159-399-1 PANEL (SV) ASSY, FRONT (GT617UE)

55 X-2149-198-1 KNOB ASSY (S)56 X-2159-462-1 PANEL (SV) ASSY, BACK57 3-250-543-21 SCREW (+B P-TITE M2)58 X-2149-228-2 CASE ASSY (for FRONT PANEL)59 2-686-945-01 CAP (USB)

FL900 1-519-916-12 INDICATOR TUBE, FLUORESCENTJ11 1-820-858-11 CONNECTOR, USB (SOCKET) (USB)RE901 1-479-902-11 ENCODER, ROTARY (PUSH SELECT/VOLUME)


5-2. FRONT PANEL SECTION

58

59

FL900

not supplied(KEY board)

not suppliednot supplied

not supplied

not supplied

not supplied

not supplied52

51

5354

55

56

57

57

RE901

J11

35


101 A-1234-480-A MECHANICAL BLOCK (U) ASSY102 A-1177-169-A DAXEV//Q

0103 X-2149-672-1 SERVICE ASSY, OP (DAX-25A)104 2-626-869-01 SCREW (M2X3), SERRATION

105 3-348-998-31 SCREW (M1.4X2.5), TAPPING, PAN106 3-352-758-31 SCREW (M1.7X2.5), TOOTHED LOCK107 A-1206-357-A SERVO BOARD, COMPLETE#6 7-627-000-08 SCREW, PRECISION +P 1.7X2.2 TYPE3


5-3. CD MECHANISM SECTION(MG-101U-188//Q)

NOTE: Refer to SUPPLEMENT-1 for disassembly of OPTICAL PICK-UP.

not supplied

#6#6

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

not supplied

101

102

103

105

104

107

106not supplied106

Ver. 1.1

36


ELECTRICAL PARTS LIST

KEY BOARD**********

< CAPACITOR >

C920 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC921 1-127-760-11 CERAMIC CHIP 4.7uF 10% 6.3VC932 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3VC971 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC991 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C992 1-165-908-11 CERAMIC CHIP 1uF 10% 10V

< CONNECTOR >

CN901 1-818-141-11 PLUG, CONNECTOR 20P

< DIODE >

D902 8-719-977-12 DIODE DTZ6.8BD903 8-719-977-12 DIODE DTZ6.8BD904 8-719-977-12 DIODE DTZ6.8BD931 8-719-404-50 DIODE MA111-TXD971 8-719-420-90 DIODE MA8051-M

D973 8-719-977-12 DIODE DTZ6.8BD976 8-719-977-12 DIODE DTZ6.8BD978 8-719-977-12 DIODE DTZ6.8BD979 8-719-977-12 DIODE DTZ6.8BD981 8-719-057-80 DIODE MA8180-M-TX

D982 6-501-089-01 DIODE RF101L2STE25D983 8-719-420-90 DIODE MA8051-MD984 8-719-057-80 DIODE MA8180-M-TXD985 8-719-977-12 DIODE DTZ6.8BD986 8-719-977-12 DIODE DTZ6.8B

D989 8-719-977-12 DIODE DTZ6.8BD990 8-719-977-12 DIODE DTZ6.8BD991 8-719-977-12 DIODE DTZ6.8BD992 8-719-977-12 DIODE DTZ6.8BD993 8-719-977-12 DIODE DTZ6.8B

D996 8-719-977-12 DIODE DTZ6.8BD997 8-719-058-24 DIODE RB501V-40TE-17D998 8-719-404-50 DIODE MA111-TX

< JUMPER RESISTOR >

FB971 1-216-864-11 SHORT CHIP 0FB991 1-216-864-11 SHORT CHIP 0

< FLUORESCENT INDICATOR TUBE >

FL900 1-519-916-12 INDICATOR TUBE, FLUORESCENT

< IC >

IC971 6-600-163-01 IC RS-770 (IR)* IC980 6-703-107-01 IC SN74LVC2G66DCUR

< CONNECTOR >

J11 1-820-858-11 CONNECTOR, USB (SOCKET) (USB)

< DIODE >

LED902 8-719-053-09 LED SML-310VTT86 (SOURCE)LED903 8-719-053-09 LED SML-310VTT86 (M > SEEK+)LED904 8-719-053-09 LED SML-310VTT86 (MODE)LED906 8-719-053-09 LED SML-310VTT86 (EQ3)LED907 8-719-053-09 LED SML-310VTT86 (. m SEEK–)

LED908 8-719-053-09 LED SML-310VTT86 (DSO)LED909 8-719-053-09 LED SML-310VTT86 (AF/TA)LED910 8-719-053-09 LED SML-310VTT86 (6/PAUSE)LED911 8-719-053-09 LED SML-310VTT86 (5/BBE MP)LED912 8-719-053-09 LED SML-310VTT86 (4/SHUF)

LED913 8-719-053-09 LED SML-310VTT86 (3/REP)LED914 8-719-053-09 LED SML-310VTT86 (2/GP/ALBM +)LED915 8-719-053-09 LED SML-310VTT86 (1/GP/ALBM –)LED916 8-719-053-09 LED SML-310VTT86 (DSPL)LED917 8-719-053-09 LED SML-310VTT86 (PTY)

LED941 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION)LED942 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION)LED943 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION)LED944 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION)LED952 8-719-078-21 LED SML-310PTT86 (SOURCE)

LED953 8-719-078-21 LED SML-310PTT86 (M > SEEK+)LED954 8-719-078-21 LED SML-310PTT86 (MODE)LED956 8-719-078-21 LED SML-310PTT86 (EQ3)LED957 8-719-078-21 LED SML-310PTT86 (. m SEEK–)LED958 8-719-078-21 LED SML-310PTT86 (DSO)

LED959 8-719-078-21 LED SML-310PTT86 (AF/TA)LED960 8-719-078-21 LED SML-310PTT86 (6/PAUSE)LED961 8-719-078-21 LED SML-310PTT86 (5/BBE MP)LED962 8-719-078-21 LED SML-310PTT86 (4/SHUF)LED963 8-719-078-21 LED SML-310PTT86 (3/REP)

LED964 8-719-078-21 LED SML-310PTT86 (2/GP/ALBM +)LED965 8-719-078-21 LED SML-310PTT86 (1/GP/ALBM –)


NOTE:• Due to standardization, replacements in

the parts list may be different from theparts specified in the diagrams or thecomponents used on the set.

• -XX and -X mean standardized parts, sothey may have some difference from theoriginal one.

• RESISTORSAll resistors are in ohms.METAL:Metal-film resistor.METAL OXIDE: Metal oxide-film resistor.F:nonflammable

• Items marked “*” are not stocked sincethey are seldom required for routine service.Some delay should be anticipatedwhen ordering these items.

• SEMICONDUCTORSIn each case, u : µ, for example:uA.. : µA.. uPA.. : µPA..uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..

• CAPACITORSuF : µF

• COILSuH : µH

The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

When indicating parts by referencenumber, please include the board.

KEY

37


LED966 8-719-078-21 LED SML-310PTT86 (DSPL)LED967 8-719-078-21 LED SML-310PTT86 (PTY)LED991 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION)LED992 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION)LED993 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION)

LED994 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION)

< COIL >

LF990 1-457-223-11 COIL, COMMON MODE CHOKE

< SWITCH >

LSW901 1-798-017-11 SWITCH, TACTILE (WITH LED) (OFF)

< TRANSISTOR >

Q503 8-729-027-23 TRANSISTOR DTA114EKA-T146Q941 6-550-752-01 TRANSISTOR DTC614TKT146Q942 6-550-752-01 TRANSISTOR DTC614TKT146Q991 8-729-026-49 TRANSISTOR 2SA1037AK-T146-RQ992 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R

Q993 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R

< RESISTOR >

R901 1-216-047-11 RES-CHIP 820 5% 1/10WR902 1-216-821-11 METAL CHIP 1K 5% 1/10WR903 1-216-821-11 METAL CHIP 1K 5% 1/10WR904 1-216-822-11 METAL CHIP 1.2K 5% 1/10WR905 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R906 1-216-824-11 METAL CHIP 1.8K 5% 1/10WR907 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR908 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR909 1-216-821-11 METAL CHIP 1K 5% 1/10WR910 1-216-821-11 METAL CHIP 1K 5% 1/10W

R911 1-216-822-11 METAL CHIP 1.2K 5% 1/10WR912 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR913 1-216-824-11 METAL CHIP 1.8K 5% 1/10WR914 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR915 1-216-827-11 METAL CHIP 3.3K 5% 1/10W

R916 1-216-828-11 METAL CHIP 3.9K 5% 1/10WR921 1-216-027-00 RES-CHIP 120 5% 1/10WR922 1-216-023-00 RES-CHIP 82 5% 1/10WR923 1-216-025-11 RES-CHIP 100 5% 1/10WR924 1-216-021-00 RES-CHIP 68 5% 1/10W

R925 1-216-027-00 RES-CHIP 120 5% 1/10WR926 1-216-023-00 RES-CHIP 82 5% 1/10WR927 1-216-025-11 RES-CHIP 100 5% 1/10WR928 1-216-021-00 RES-CHIP 68 5% 1/10WR929 1-216-027-00 RES-CHIP 120 5% 1/10W







R962 1-216-864-11 SHORT CHIP 0R963 1-216-864-11 SHORT CHIP 0R964 1-216-001-00 RES-CHIP 10 5% 1/10WR965 1-216-001-00 RES-CHIP 10 5% 1/10WR966 1-216-833-11 METAL CHIP 10K 5% 1/10W

R967 1-216-833-11 METAL CHIP 10K 5% 1/10WR968 1-216-864-11 SHORT CHIP 0R969 1-216-833-11 METAL CHIP 10K 5% 1/10WR971 1-216-811-11 METAL CHIP 150 5% 1/10WR972 1-216-809-11 METAL CHIP 100 5% 1/10W

R973 1-216-811-11 METAL CHIP 150 5% 1/10WR981 1-216-864-11 SHORT CHIP 0R982 1-216-864-11 SHORT CHIP 0R983 1-216-864-11 SHORT CHIP 0R984 1-216-809-11 METAL CHIP 100 5% 1/10W

R985 1-216-809-11 METAL CHIP 100 5% 1/10WR986 1-216-809-11 METAL CHIP 100 5% 1/10WR987 1-216-845-11 METAL CHIP 100K 5% 1/10WR988 1-216-821-11 METAL CHIP 1K 5% 1/10WR989 1-216-821-11 METAL CHIP 1K 5% 1/10W

R990 1-216-821-11 METAL CHIP 1K 5% 1/10WR991 1-216-833-11 METAL CHIP 10K 5% 1/10WR992 1-216-833-11 METAL CHIP 10K 5% 1/10WR993 1-216-833-11 METAL CHIP 10K 5% 1/10WR994 1-216-845-11 METAL CHIP 100K 5% 1/10W

R995 1-216-845-11 METAL CHIP 100K 5% 1/10WR996 1-216-845-11 METAL CHIP 100K 5% 1/10W

< ROTARY ENCODER >

RE901 1-479-902-11 ENCODER, ROTARY (PUSH SELECT/VOLUME)

< SWITCH >

S902 1-786-653-21 SWITCH, TACTILE (SOURCE)S903 1-786-653-21 SWITCH, TACTILE (M > SEEK+)S904 1-786-653-21 SWITCH, TACTILE (MODE)S906 1-786-653-21 SWITCH, TACTILE (EQ3)S907 1-786-653-21 SWITCH, TACTILE (. m SEEK–)


KEY

38


S908 1-786-653-21 SWITCH, TACTILE (DSO)S909 1-786-653-21 SWITCH, TACTILE (AF/TA)S910 1-786-653-21 SWITCH, TACTILE (6/PAUSE)S911 1-786-653-21 SWITCH, TACTILE (5/BBE MP)S912 1-786-653-21 SWITCH, TACTILE (4/SHUF)

S913 1-786-653-21 SWITCH, TACTILE (3/REP)S914 1-786-653-21 SWITCH, TACTILE (2/GP/ALBM +)S915 1-786-653-21 SWITCH, TACTILE (1/GP/ALBM –)S916 1-786-653-21 SWITCH, TACTILE (DSPL)S917 1-786-653-21 SWITCH, TACTILE (PTY)

S918 1-798-032-11 SWITCH, DETECTION (OPEN/CLOSE)*************************************************************

A-1217-699-A MAIN BOARD, COMPLETE (GT610U/GT616U)A-1217-728-A MAIN BOARD, COMPLETE (GT617UE)

*********************

7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT7-685-794-09 SCREW +PTT 2.6X10 (S)

< CAPACITOR >

C1 1-126-963-11 ELECT 4.7uF 20% 50VC2 1-126-947-11 ELECT 47uF 20% 35VC3 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC5 1-126-947-11 ELECT 47uF 20% 35VC7 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C8 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50VC9 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC14 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC50 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC51 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C52 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC53 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC54 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC55 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC56 1-162-917-11 CERAMIC CHIP 15PF 5% 50V

C57 1-162-917-11 CERAMIC CHIP 15PF 5% 50VC58 1-162-959-11 CERAMIC CHIP 330PF 5% 50VC60 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC61 1-126-947-11 ELECT 47uF 20% 35VC62 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

C103 1-165-319-11 CERAMIC CHIP 0.1uF 50VC104 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC108 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC109 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC110 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C114 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC301 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC303 1-128-551-11 ELECT 22uF 20% 63VC304 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC305 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C306 1-126-964-11 ELECT 10uF 20% 50VC307 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC308 1-126-964-11 ELECT 10uF 20% 50VC309 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC310 1-126-916-11 ELECT 1000uF 20% 6.3V

C312 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC313 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC314 1-124-261-00 ELECT 10uF 20% 50V

C315 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC316 1-124-261-00 ELECT 10uF 20% 50VC317 1-124-257-00 ELECT 2.2uF 20% 50VC318 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC319 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V


C328 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16VC360 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC361 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC362 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC363 1-124-257-00 ELECT 2.2uF 20% 50V

C364 1-124-257-00 ELECT 2.2uF 20% 50VC401 1-124-584-00 ELECT 100uF 20% 10VC402 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC403 1-126-176-11 ELECT 220uF 20% 10VC405 1-124-248-00 ELECT 22uF 20% 25V

C410 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC411 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC412 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC413 1-163-251-11 CERAMIC CHIP 100PF 5% 50VC414 1-163-251-11 CERAMIC CHIP 100PF 5% 50V

C415 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC417 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC418 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC419 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC421 1-126-791-11 ELECT 10uF 20% 35V

C422 1-163-251-11 CERAMIC CHIP 100PF 5% 50VC423 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC429 1-124-261-00 ELECT 10uF 20% 50VC430 1-124-261-00 ELECT 10uF 20% 50VC431 1-126-791-11 ELECT 10uF 20% 35V

C432 1-163-251-11 CERAMIC CHIP 100PF 5% 50VC441 1-126-791-11 ELECT 10uF 20% 35VC442 1-163-251-11 CERAMIC CHIP 100PF 5% 50VC443 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC446 1-165-908-11 CERAMIC CHIP 1uF 10% 10V

C447 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC452 1-163-251-11 CERAMIC CHIP 100PF 5% 50VC454 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50VC461 1-126-791-11 ELECT 10uF 20% 35VC462 1-165-908-11 CERAMIC CHIP 1uF 10% 10V

C465 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC466 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC470 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC471 1-126-791-11 ELECT 10uF 20% 35VC472 1-165-908-11 CERAMIC CHIP 1uF 10% 10V

C480 1-136-159-00 FILM 0.033uF 5% 50VC481 1-136-159-00 FILM 0.033uF 5% 50VC482 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC483 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC484 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C485 1-104-665-11 ELECT 100uF 20% 25VC487 1-126-791-11 ELECT 10uF 20% 35VC491 1-124-589-11 ELECT 47uF 20% 16V


MAINKEY

39


C501 1-128-057-11 ELECT 330uF 20% 6.3VC502 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC503 1-124-584-00 ELECT 100uF 20% 10VC504 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC505 1-124-584-00 ELECT 100uF 20% 10V


C511 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC512 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC513 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC515 1-162-917-11 CERAMIC CHIP 15PF 5% 50VC516 1-162-918-11 CERAMIC CHIP 18PF 5% 50V

C519 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC523 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC600 1-126-935-11 ELECT 470uF 20% 16VC601 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC602 1-165-319-11 CERAMIC CHIP 0.1uF 50V

C701 1-131-868-81 ELECT 3300uF 20% 16VC702 1-126-160-11 ELECT 1uF 20% 50VC703 1-126-163-11 ELECT 4.7uF 20% 50VC704 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC705 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C801 1-126-933-11 ELECT 100uF 20% 16VC802 1-126-934-11 ELECT 220uF 20% 16VC803 1-104-665-11 ELECT 100uF 20% 25VC804 1-126-963-11 ELECT 4.7uF 20% 50VC805 1-126-933-11 ELECT 100uF 20% 16V

C806 1-126-934-11 ELECT 220uF 20% 16VC809 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC810 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC811 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC812 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V


C822 1-126-933-11 ELECT 100uF 20% 16VC830 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC901 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50VC902 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50VC998 1-216-864-11 SHORT CHIP 0

< CONNECTOR >

CN300 1-774-701-21 PIN, CONNECTOR 16PCN350 1-820-611-11 CONNECTOR, BOARD TO BOARD 28P

* CN410 1-564-506-11 PLUG, CONNECTOR 3PCN802 1-569-913-11 SOCKET, CONNECTOR 20PCNJ400 1-580-907-41 PLUG, CONNECTOR 8P (BUS CONTROL IN)

< DIODE >

D2 8-719-977-03 DIODE DTZ5.6BD101 8-719-977-12 DIODE DTZ6.8BD102 8-719-420-90 DIODE MA8051-MD103 8-719-057-80 DIODE MA8180-M-TXD104 8-719-057-80 DIODE MA8180-M-TX

D105 8-719-420-90 DIODE MA8051-MD106 8-719-420-90 DIODE MA8051-MD107 8-719-420-90 DIODE MA8051-MD108 8-719-420-90 DIODE MA8051-MD109 8-719-420-90 DIODE MA8051-M

D110 8-719-420-90 DIODE MA8051-MD114 8-719-420-90 DIODE MA8051-MD115 8-719-978-33 DIODE DTZ-TT11-6.8BD118 8-719-977-12 DIODE DTZ6.8BD119 8-719-057-80 DIODE MA8180-M-TX

D120 8-719-420-90 DIODE MA8051-MD301 6-500-522-01 DIODE 10EDB40-TA1B2D302 6-500-522-01 DIODE 10EDB40-TA1B2D303 6-500-522-01 DIODE 10EDB40-TA1B2D304 6-500-522-01 DIODE 10EDB40-TA1B2

D305 6-500-522-01 DIODE 10EDB40-TA1B2D306 6-500-522-01 DIODE 10EDB40-TA1B2D307 6-500-522-01 DIODE 10EDB40-TA1B2D308 6-500-522-01 DIODE 10EDB40-TA1B2D309 6-500-522-01 DIODE 10EDB40-TA1B2

D310 6-500-522-01 DIODE 10EDB40-TA1B2D311 6-500-522-01 DIODE 10EDB40-TA1B2D312 6-500-522-01 DIODE 10EDB40-TA1B2D400 6-501-013-01 DIODE BAT54ALT1GD471 8-719-977-12 DIODE DTZ6.8B

D491 8-719-404-50 DIODE MA111-TXD501 8-719-050-37 DIODE M1MA152WA-T1D502 8-719-060-48 DIODE RB751V-40TE-17D602 8-719-057-80 DIODE MA8180-M-TXD603 8-719-422-67 DIODE MA8062-H

D604 8-719-057-80 DIODE MA8180-M-TXD605 8-719-057-80 DIODE MA8180-M-TXD606 8-719-072-70 DIODE MA2ZD14001S0D607 6-501-571-01 DIODE 1N5404-C311-3D701 8-719-057-80 DIODE MA8180-M-TX

D702 8-719-057-80 DIODE MA8180-M-TXD703 8-719-420-90 DIODE MA8051-MD704 8-719-057-80 DIODE MA8180-M-TXD705 8-719-081-97 DIODE MMDL914T1D801 6-501-657-01 DIODE MA24D5000BS0

D802 8-719-420-90 DIODE MA8051-MD903 8-719-057-80 DIODE MA8180-M-TX

< FERRITE BEAD >

FB401 1-216-295-11 SHORT CHIP 0FB402 1-216-864-11 SHORT CHIP 0FB403 1-216-864-11 SHORT CHIP 0FB404 1-216-295-11 SHORT CHIP 0FB405 1-216-864-11 SHORT CHIP 0

FB406 1-216-864-11 SHORT CHIP 0FB407 1-216-295-11 SHORT CHIP 0FB408 1-469-876-11 INDUCTOR, FERRITE BEADFB801 1-216-864-11 SHORT CHIP 0FB802 1-216-864-11 SHORT CHIP 0

FB803 1-216-864-11 SHORT CHIP 0FB804 1-216-821-11 METAL CHIP 1K 5% 1/10W


MAIN

40


< IC >

IC50 6-803-747-01 IC TDA7333013TRIC300 6-705-359-02 IC TDA8588AJ/N2/R1 (GT617UE)IC300 6-705-359-11 IC TDA8588AJ/N2/R1/M5 (GT610U/GT616U)IC401 6-710-065-01 IC BD3442FS-E2IC501 6-807-002-01 IC MB90F046PF-G-102E1 (GT610U/GT616U)

IC501 6-807-259-01 IC MB90F046PF-G-104E1 (GT617UE)IC502 6-704-529-01 IC XC6206P332PRIC601 6-703-884-01 IC BA8271F-E2IC602 6-703-224-01 IC S-80828CNNB-B8NT2GIC801 6-710-493-01 IC NJM2370U1-12-TE2

IC802 6-707-911-01 IC BD9778HFPIC803 6-710-624-01 IC TPS2051BDRG4IC804 8-759-460-72 IC BA033FP-E2

< JACK >

J1 1-815-185-13 JACK (ANTENNA)J370 1-566-822-41 JACK (REMOTE IN)J451 1-774-700-41 JACK, PIN 6P (BUS AUDIO IN,

AUDIO OUT REAR/FRONT)

< JUMPER RESISTOR >

JC3 1-216-864-11 SHORT CHIP 0JC9 1-216-295-11 SHORT CHIP 0JC32 1-216-864-11 SHORT CHIP 0JC53 1-216-864-11 SHORT CHIP 0JC90 1-216-296-11 SHORT CHIP 0








JC997 1-216-864-11 SHORT CHIP 0JC998 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VJC999 1-216-864-11 SHORT CHIP 0

< COIL >

L1 1-500-245-11 INDUCTOR, FERRITE BEADL2 1-414-595-11 INDUCTOR, FERRITE BEADL3 1-414-595-11 INDUCTOR, FERRITE BEADL4 1-469-844-11 INDUCTOR 2.2uHL101 1-410-509-11 INDUCTOR 10uH

L300 1-456-617-11 COIL, CHOKEL301 1-216-864-11 SHORT CHIP 0L302 1-216-864-11 SHORT CHIP 0L303 1-216-864-11 SHORT CHIP 0L500 1-469-844-11 INDUCTOR 2.2uH

L801 1-457-418-11 COIL, CHOKEL802 1-457-378-11 COIL, CHOKEL803 1-457-418-11 COIL, CHOKE

< TRANSISTOR >

Q1 1-801-806-11 TRANSISTOR DTC144EKAQ3 8-729-106-68 TRANSISTOR 2SD1615A-GPQ50 8-729-026-49 TRANSISTOR 2SA1037AK-T146-RQ420 6-550-752-01 TRANSISTOR DTC614TKT146Q423 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R

Q424 6-550-752-01 TRANSISTOR DTC614TKT146Q426 6-550-752-01 TRANSISTOR DTC614TKT146Q430 6-550-752-01 TRANSISTOR DTC614TKT146Q440 6-550-752-01 TRANSISTOR DTC614TKT146Q460 6-550-752-01 TRANSISTOR DTC614TKT146

Q470 6-550-752-01 TRANSISTOR DTC614TKT146Q471 6-550-683-01 FET RJK005N03-T146Q491 8-729-027-23 TRANSISTOR DTA114EKA-T146Q492 8-729-027-43 TRANSISTOR DTC114EKA-T146Q501 8-729-027-23 TRANSISTOR DTA114EKA-T146

Q589 8-729-027-43 TRANSISTOR DTC114EKA-T146Q590 8-729-027-23 TRANSISTOR DTA114EKA-T146Q605 8-729-027-43 TRANSISTOR DTC114EKA-T146Q701 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q702 8-729-120-28 TRANSISTOR 2SC1623-L5L6

Q703 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q801 1-801-806-11 TRANSISTOR DTC144EKA

< RESISTOR >

R1 1-216-809-11 METAL CHIP 100 5% 1/10WR2 1-216-839-11 METAL CHIP 33K 5% 1/10WR3 1-216-843-11 METAL CHIP 68K 5% 1/10WR4 1-216-839-11 METAL CHIP 33K 5% 1/10WR5 1-216-843-11 METAL CHIP 68K 5% 1/10W

R6 1-414-595-11 INDUCTOR, FERRITE BEADR7 1-414-595-11 INDUCTOR, FERRITE BEADR8 1-216-839-11 METAL CHIP 33K 5% 1/10WR9 1-216-843-11 METAL CHIP 68K 5% 1/10W


MAIN

41


R10 1-216-821-11 METAL CHIP 1K 5% 1/10WR11 1-216-864-11 SHORT CHIP 0R12 1-414-595-11 INDUCTOR, FERRITE BEADR13 1-414-595-11 INDUCTOR, FERRITE BEADR14 1-216-864-11 SHORT CHIP 0

R52 1-216-845-11 METAL CHIP 100K 5% 1/10WR53 1-216-797-11 METAL CHIP 10 5% 1/10WR54 1-414-595-11 INDUCTOR, FERRITE BEADR55 1-216-797-11 METAL CHIP 10 5% 1/10WR57 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R58 1-216-821-11 METAL CHIP 1K 5% 1/10WR301 1-216-811-11 METAL CHIP 150 5% 1/10WR302 1-216-841-11 METAL CHIP 47K 5% 1/10WR351 1-216-845-11 METAL CHIP 100K 5% 1/10WR370 1-216-809-11 METAL CHIP 100 5% 1/10W

R371 1-216-809-11 METAL CHIP 100 5% 1/10WR401 1-216-813-11 METAL CHIP 220 5% 1/10WR402 1-216-813-11 METAL CHIP 220 5% 1/10WR411 1-216-833-11 METAL CHIP 10K 5% 1/10WR416 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R417 1-216-833-11 METAL CHIP 10K 5% 1/10WR418 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR419 1-216-833-11 METAL CHIP 10K 5% 1/10WR420 1-216-809-11 METAL CHIP 100 5% 1/10WR421 1-216-809-11 METAL CHIP 100 5% 1/10W

R422 1-216-833-11 METAL CHIP 10K 5% 1/10WR423 1-216-845-11 METAL CHIP 100K 5% 1/10WR424 1-216-833-11 METAL CHIP 10K 5% 1/10WR425 1-216-833-11 METAL CHIP 10K 5% 1/10WR431 1-216-809-11 METAL CHIP 100 5% 1/10W

R432 1-216-833-11 METAL CHIP 10K 5% 1/10WR433 1-218-883-11 METAL CHIP 33K 0.5% 1/10WR440 1-216-809-11 METAL CHIP 100 5% 1/10WR441 1-216-809-11 METAL CHIP 100 5% 1/10WR442 1-216-833-11 METAL CHIP 10K 5% 1/10W

R450 1-216-809-11 METAL CHIP 100 5% 1/10WR452 1-216-833-11 METAL CHIP 10K 5% 1/10WR453 1-216-864-11 SHORT CHIP 0R454 1-216-864-11 SHORT CHIP 0R455 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R460 1-216-809-11 METAL CHIP 100 5% 1/10WR461 1-216-809-11 METAL CHIP 100 5% 1/10WR470 1-216-809-11 METAL CHIP 100 5% 1/10WR471 1-216-809-11 METAL CHIP 100 5% 1/10WR474 1-216-821-11 METAL CHIP 1K 5% 1/10W

R480 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR481 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR482 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR483 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR484 1-216-821-11 METAL CHIP 1K 5% 1/10W

R491 1-216-805-11 METAL CHIP 47 5% 1/10WR500 1-216-817-11 METAL CHIP 470 5% 1/10WR502 1-216-845-11 METAL CHIP 100K 5% 1/10WR503 1-216-845-11 METAL CHIP 100K 5% 1/10W

(GT610U/GT616U)R504 1-216-845-11 METAL CHIP 100K 5% 1/10W

(GT617UE)

Ref. No. Part No. Description Remark

R505 1-216-845-11 METAL CHIP 100K 5% 1/10W(GT610U/GT616U)

R506 1-216-845-11 METAL CHIP 100K 5% 1/10W(GT617UE)

R509 1-216-845-11 METAL CHIP 100K 5% 1/10WR510 1-216-833-11 METAL CHIP 10K 5% 1/10WR512 1-216-845-11 METAL CHIP 100K 5% 1/10W

R513 1-216-809-11 METAL CHIP 100 5% 1/10WR514 1-216-809-11 METAL CHIP 100 5% 1/10WR515 1-216-809-11 METAL CHIP 100 5% 1/10WR516 1-216-809-11 METAL CHIP 100 5% 1/10WR517 1-216-845-11 METAL CHIP 100K 5% 1/10W

R518 1-216-845-11 METAL CHIP 100K 5% 1/10WR519 1-218-871-11 METAL CHIP 10K 0.5% 1/10WR520 1-218-871-11 METAL CHIP 10K 0.5% 1/10WR521 1-216-821-11 METAL CHIP 1K 5% 1/10WR522 1-218-871-11 METAL CHIP 10K 0.5% 1/10W



R533 1-216-845-11 METAL CHIP 100K 5% 1/10WR534 1-216-845-11 METAL CHIP 100K 5% 1/10WR535 1-216-809-11 METAL CHIP 100 5% 1/10WR536 1-216-811-11 METAL CHIP 150 5% 1/10WR537 1-216-845-11 METAL CHIP 100K 5% 1/10W

R539 1-216-809-11 METAL CHIP 100 5% 1/10WR540 1-216-809-11 METAL CHIP 100 5% 1/10WR541 1-216-849-11 METAL CHIP 220K 5% 1/10WR542 1-216-845-11 METAL CHIP 100K 5% 1/10WR543 1-216-845-11 METAL CHIP 100K 5% 1/10W

R545 1-216-845-11 METAL CHIP 100K 5% 1/10WR546 1-216-845-11 METAL CHIP 100K 5% 1/10WR547 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR548 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR549 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R551 1-216-864-11 SHORT CHIP 0R553 1-216-821-11 METAL CHIP 1K 5% 1/10WR554 1-216-821-11 METAL CHIP 1K 5% 1/10WR555 1-216-833-11 METAL CHIP 10K 5% 1/10WR556 1-216-833-11 METAL CHIP 10K 5% 1/10W

R557 1-216-809-11 METAL CHIP 100 5% 1/10WR558 1-216-809-11 METAL CHIP 100 5% 1/10WR559 1-216-845-11 METAL CHIP 100K 5% 1/10WR561 1-216-845-11 METAL CHIP 100K 5% 1/10W

(GT617UE)R562 1-216-845-11 METAL CHIP 100K 5% 1/10W

(GT610U/GT616U)

R563 1-216-845-11 METAL CHIP 100K 5% 1/10WR570 1-216-864-11 SHORT CHIP 0R571 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR572 1-216-845-11 METAL CHIP 100K 5% 1/10WR573 1-216-845-11 METAL CHIP 100K 5% 1/10W


MAIN

42


R574 1-216-845-11 METAL CHIP 100K 5% 1/10WR600 1-216-864-11 SHORT CHIP 0R601 1-216-851-11 METAL CHIP 330K 5% 1/10WR602 1-216-851-11 METAL CHIP 330K 5% 1/10WR603 1-216-821-11 METAL CHIP 1K 5% 1/10W

R604 1-216-835-11 METAL CHIP 15K 5% 1/10WR605 1-216-809-11 METAL CHIP 100 5% 1/10WR606 1-216-821-11 METAL CHIP 1K 5% 1/10WR607 1-216-821-11 METAL CHIP 1K 5% 1/10WR610 1-216-809-11 METAL CHIP 100 5% 1/10W

R611 1-216-809-11 METAL CHIP 100 5% 1/10WR701 1-216-821-11 METAL CHIP 1K 5% 1/10WR702 1-216-841-11 METAL CHIP 47K 5% 1/10WR703 1-216-833-11 METAL CHIP 10K 5% 1/10WR704 1-216-833-11 METAL CHIP 10K 5% 1/10W

R705 1-249-425-11 CARBON 4.7K 5% 1/4WR706 1-216-841-11 METAL CHIP 47K 5% 1/10WR707 1-216-841-11 METAL CHIP 47K 5% 1/10WR708 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR709 1-216-049-11 RES-CHIP 1K 5% 1/10W

R710 1-249-425-11 CARBON 4.7K 5% 1/4WR711 1-216-845-11 METAL CHIP 100K 5% 1/10WR712 1-216-837-11 METAL CHIP 22K 5% 1/10WR801 1-218-869-11 METAL CHIP 8.2K 0.5% 1/10WR802 1-218-883-11 METAL CHIP 33K 0.5% 1/10W

R803 1-218-871-11 METAL CHIP 10K 0.5% 1/10WR804 1-218-907-11 METAL CHIP 330K 0.5% 1/10WR805 1-218-893-11 METAL CHIP 82K 0.5% 1/10WR806 1-216-821-11 METAL CHIP 1K 5% 1/10WR808 1-216-821-11 METAL CHIP 1K 5% 1/10W

R809 1-216-821-11 METAL CHIP 1K 5% 1/10WR810 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR811 1-216-821-11 METAL CHIP 1K 5% 1/10WR812 1-216-833-11 METAL CHIP 10K 5% 1/10WR813 1-216-821-11 METAL CHIP 1K 5% 1/10W

R830 1-216-797-11 METAL CHIP 10 5% 1/10W

< SWITCH >

S102 1-786-458-11 SWITCH, PUSH (1 KEY) (NOSE DET)S103 1-692-431-21 SWITCH, TACTILE (RESET)

< THERMISTOR (POSITIVE) >

TH400 1-803-350-21 THERMISTOR, POSITIVE

< TUNER UNIT >

TU1 A-3220-961-B TUNER UNIT (TUX-032)

< VIBRATOR >

X50 1-813-532-11 VIBRATOR, CRYSTAL (8.664MHz)X500 1-813-524-21 VIBRATOR, CERAMIC (18.432MHz)X501 1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz)

*************************************************************

A-1206-357-A SERVO BOARD, COMPLETE**********************

*************************************************************

SUB BOARD**********

1-833-591-11 CABLE, FLEXIBLE FLAT (20 CORE)

< CAPACITOR >

C202 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

< CONNECTOR >

CN201 1-818-142-11 SOCKET, CONNECTOR 20PCN203 1-691-550-11 PIN, CONNECTOR (1.5mm) (SMD) 3P

< DIODE >

D203 8-719-420-90 DIODE MA8051-MD204 8-719-420-90 DIODE MA8051-MLED201 8-719-053-09 LED SML-310VTT86 (CD INDICATOR)

(GT610U/GT616U)LED201 8-719-078-21 LED SML-310PTT86 (CD INDICATOR)

(GT617UE)LED202 8-719-053-09 LED SML-310VTT86 (Z) (GT610U/GT616U)

LED202 8-719-078-21 LED SML-310PTT86 (Z) (GT617UE)

< RESISTOR >

R201 1-216-812-11 METAL CHIP 180 5% 1/10WR202 1-216-815-11 METAL CHIP 330 5% 1/10WR203 1-216-797-11 METAL CHIP 10 5% 1/10WR204 1-216-797-11 METAL CHIP 10 5% 1/10WR205 1-216-864-11 SHORT CHIP 0

< SWITCH >

S201 1-786-653-21 SWITCH, TACTILE (Z)*************************************************************

MISCELLANEOUS***************

12 1-831-837-11 CORD (WITH CONNECTOR) (ISO) (POWER)13 1-833-887-11 CONNECTION CORD (RCA) (SUB OUT (MONO))

0103 X-2149-672-1 SERVICE ASSY, OP (DAX-25A)FU601 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A

*************************************************************

ACCESSORIES************

1-479-077-13 REMOTE COMMANDER (RM-X151)2-548-729-01 LID, BATTERY CASE (for RM-X151)2-888-758-31 MANUAL, INSTRUCTION (ENGLISH,GERMAN,

FRENCH,ITALIAN,DUTCH)(GT610U/GT616U)

2-888-758-41 MANUAL, INSTRUCTION (ENGLISH,RUSSIAN)(GT617UE)

2-888-759-31 MANUAL, INSTRUCTION, INSTALL (ENGLISH,GERMAN,FRENCH,ITALIAN,DUTCH)

(GT610U/GT616U)

2-888-759-41 MANUAL, INSTRUCTION, INSTALL (ENGLISH,RUSSIAN) (GT617UE)

X-2149-228-2 CASE ASSY (for FRONT PANEL)*************************************************************

MAIN SERVO


SUBVer. 1.1

43


PARTS FOR INSTALLATION AND CONNECTIONS***************************************

151 X-3382-647-1 FRAME ASSY, FITTING152 2-638-099-01 COLLAR153 3-246-471-01 KEY (FRAME)154 X-3381-154-1 SCREW ASSY (BS4), FITTING (GT617UE)155 X-3382-926-1 SCREW ASSY (BS), FITTING (GT610U/GT616U)

156 3-349-410-11 BUSHING157 1-465-459-31 ADAPTOR, ANTENNA158 1-831-837-11 CORD (WITH CONNECTOR) (ISO) (POWER)


151

154

152

156

157

153

× 2

158

156155

× 4

44


MEMO

SERVICE MANUAL

9-887-473-81

Ver. 1.1 2007.03

SUPPLEMENT-1File this supplement with the service manual.

Subject: Notes for removal of the OPTICAL PICK-UP added.

DISASSEMBLY

1. CHUCKING ARM SUB ASSY

3 chucking arm sub assy

2

1 spring

Note: Have this portion receive the chassis. Note: Have this portion receive the chassis.

Note: Be careful not to touch the turn table.

AEP ModelUK Model

CDX-GT610U/GT616U

East European ModelCDX-GT617UE


2


2. SLED MOTOR ASSY

3 sled mtor assy

sled mtor assy

1 spring

spring

stand

stand

turn table

2 three serration screws(M 2 × 3)

three serration screws(M 2 × 3)

Note: Place the stand with care not to touch the turn table.

Note: Never remove these parts since they were adjusted.

Note for Assembly

Note: Take care to prevent the chassis from being bent when tightening the three machine screws.

3


3. OPTICAL PICK-UP SECTION

4. OPTICAL PICK-UP

1

2 optical pick-up section

Note: Be careful not to touch the lens and hologram terminal when removing the optical pick-up section.

There is space at the end of the leaf spring (sub guide) to avoid contact with the slide.

1 pan tapping screw(M 1.4 × 2.5)

2 leaf spring (sub guide)

3 leaf spring (OP)

5 optical pick-up

4 lead screw assy

Notes for Assembly

Prevent the end of the leaf spring (sub guide) from being in contact with the OP slide base.

Prevent the end of the leaf spring (sub guide) from being in contact with the OP slide base.

4


REVISION HISTORY

Clicking the version allows you to jump to the revised page.Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.

Ver. Date Description of Revision

1.0 2006.11 New

1.1 2007.03 Change of initial illumination color of CDX-GT617UE.

Notes for removal of the OPTICAL PICK-UP added.

(SUPPLEMENT-1) (ECN-ECC04028/ECC08328, ENG-07003)

service manual aep model - especarchive.espec.ws/files/sony cdx-gt610u_gt616u_gt617ue.pdf3...

Documents