service manual revised - electronica … the radio from its shipping ... many factors and is beyond...
TRANSCRIPT
© 2003-6 PRINTED IN JAPANB51-8610-10 (N) 975
VHF FM TRANSCEIVER
TK-7102HSERVICE MANUAL
Panel assy(A62-0942-03)
Front glass(B10-2753-03)
Cabinet(A01-2181-01)
Chassis(A10-4048-21)
Key top(K29-9065-01)
Modular jack(E08-0877-05)
GENERAL .................................................. 2
SYSTEM SET-UP ...................................... 3
OPERATING FEATURES .......................... 4
REALIGNMENT ......................................... 8
INSTALLATION ....................................... 11
DISASSEMBLY FOR REPAIR ................. 13
CIRCUIT DESCRIPTION .......................... 14
SEMICONDUCTOR DATA ...................... 18
COMPONENTS DESCRIPTION .............. 20
PARTS LIST ............................................. 21
EXPLODED VIEW.................................... 27
PACKING ................................................. 28
ADJUSTMENT ........................................ 29
TERMINAL FUNCTION ........................... 34
PC BOARD
DISPLAY UNIT (X54-3460-20) ............ 35
TX-RX UNIT (X57-6700-XX) ............... 37
SCHEMATIC DIAGRAM.......................... 43
BLOCK DIAGRAM ................................... 47
LEVEL DIAGRAM .................................... 49
SPECIFICATION ...................................... 51
CONTENTS
REVISEDThis service manual applies to products with 50300001 or subsequent serial numbers.In terms of the products with the serial numbers earlier than 50300001, refer to the TK-7102H service manual as per part No.B51-8610-00 and B51-8627-00.
Service Manual List
Title Parts number Remarks Destination TX-RX unit number Display unit number
TK-7102H B51-8610-00 M X57-6380-20 X54-3340-20
TK-7102H B51-8627-00 SUPPLEMENT K,K2,M,M2 X57-6380-XX X54-3340-20
TK-7102H B51-8610-10 REVISED K,K2,M,M2 X57-6700-XX X54-3460-20(This service manual)
TK-7102H
2
INTRODUCTION
SCOPE OF THIS MANUALThis manual is intended for use by experienced techni-
cians familiar with similar types of commercial grade commu-nications equipment. It contains all required service informa-tion for the equipment and is current as of this publicationdate. Changes which may occur after publication are coveredby either Service Bulletins or Manual Revisions, which areissued as required.
ORDERING REPLACEMENT PARTSWhen ordering replacement parts or equipment informa-
tion, the full part identification number should be included.This applies to all parts : components, kits, and chassis. If thepart number is not known, include the chassis or kit numberof which it is a part and a sufficient description of the requiredcomponent for proper identification.
PERSONNEL SAFETYThe following precautions are recommended for person-
nel safety :• DO NOT transmit if someone is within two feet (0.6
meter) of the antenna.• DO NOT transmit until all RF connectors are secure and
any open connectors are properly terminated.• SHUT OFF this equipment when near electrical blasting
caps or while in an explosive atmosphere.• All equipment should be properly grounded before power-
up for safe operation.• This equipment should be serviced by only qualified tech-
nicians.
PRE-INSTALLATION CONSIDERATIONS
1. UNPACKINGUnpack the radio from its shipping container and check for
accessory items. If any item is missing, please contactKENWOOD immediately.
2. LICENSING REQUIREMENTSFederal regulations require a station license for each radio
installation (mobile or base) be obtained by the equipmentowner. The licensee is responsible for ensuring transmitterpower, frequency, and deviation are within the limits permit-ted by the station license.
Transmitter adjustments may be performed only by a li-censed technician holding an FCC first, second or generalclass commercial radiotelephone operator’s license. There isno license required to install or operate the radio.
3. PRE-INSTALLATION CHECKOUT
3-1. IntroductionEach radio is adjusted and tested before shipment. How-
ever, it is recommended that receiver and transmitter opera-tion be checked for proper operation before installation.
3-2. TestingThe radio should be tested complete with all cabling and
accessories as they will be connected in the final installation.Transmitter frequency, deviation, and power output shouldbe checked, as should receiver sensitivity, squelch operation,and audio output. Signalling equipment operation should beverified.
4. PLANNING THE INSTALLATION
4-1. GeneralInspect the vehicle and determine how and where the ra-
dio antenna and accessories will be mounted.Plan cable runs for protection against pinching or crushing
wiring, and radio installation to prevent overheating.
4-2. AntennaThe favored location for an antenna is in the center of a
large, flat conductive area, usually at the roof center. Thetrunk lid is preferred, bond the trunk lid and vehicle chassisusing ground straps to ensure the lid is at chassis ground.
4-3. RadioThe universal mount bracket allows the radio to be
mounted in a variety of ways. Be sure the mounting surfaceis adequate to support the radio’s weight. Allow sufficientspace around the radio for air cooling. Position the radio closeenough to the vehicle operator to permit easy access to thecontrols when driving.
4-4. DC Power and wiring1. This radio may be installed in negative ground electrical
systems only. Reverse polarity will cause the cable fuse toblow. Check the vehicle ground polarity before installationto prevent wasted time and effort.
2. Connect the positive power lead directly to the vehiclebattery positive terminal. Connecting the Positive lead toany other positive voltage source in the vehicle is not rec-ommended.
3. Connect the ground lead directly to the battery negativeterminal.
4. The cable provided with the radio is sufficient to handlethe maximum radio current demand. If the cable must beextended, be sure the additional wire is sufficient for thecurrent to be carried and length of the added lead.
GENERAL
TK-7102H
3
5. INSTALLATION PLANNING – CONTROL STATIONS
5-1. Antenna systemControl station. The antenna system selection depends on
many factors and is beyond the scope of this manual. YourKENWOOD dealer can help you select an antenna systemthat will best serve your particular needs.
5-2. Radio locationSelect a convenient location for your control station radio
which is as close as practical to the antenna cable entry point.Secondly, use your system’s power supply (which suppliesthe voltage and current required for your system). Make suresufficient air can flow around the radio and power supply toallow adequate cooling.
SERVICEThis radio is designed for easy servicing. Refer to the
schematic diagrams, printed circuit board views, and align-ment procedures contained in this manual.
Speakerjack cap
Power inputconnector
Antennaconnector
NOTEIf you do not intend to use the 3.5-mm jack for the external
speaker, fit the supplied speaker-jack cap to stop dust andsand from getting in.
Merchandise received
License and frequency allocated by FCC
Choose the type of transceiver
Transceiver programming
KCT-39Connection cable
KCT-18Ignition sense cable
KCT-36Extension cable
KDS-100Mobile data
terminal
KGP-2AModem GPS receiver or
KGP-2BModem GPS controller
KES-3External speaker
See page 8.A personal computer (IBM PC or compatible), programming interface (KPG-46),and programming software (KPG-70D) are required for programming.
Frequency range (MHz) RF power Type
146~174 50W K,M
136~162 50W K2,M2
(Option)(Option)
(Option)
(Option)(Option)
(Option)
or
Delivery
GENERAL / SYSTEM SET-UP
SYSTEM SET-UP
TK-7102H
4
OPERATING FEATURES
Indicator Description
Light while transmitting.
Lights when a signal is detected on
the currently selected channel.
Lights while the function programmed
onto its corresponding key is activated.
Lights while the function programmed
onto its corresponding key is activated.
Lights to display the currently selected
channel (1~ 4).
1-5. Rear panel
Externalspeakerjack
Power inputconnector
Antennaconnector
1. Controls and Functions
1-1. Front Panel
q (Power) switchPress to switch the transceiver ON. Press and hold forapproximately 1 seconds to switch the transceiver OFF.
w keyPress to increase the volume level.
e keyPress to decrease the volume level.
r keyPF (Programmable Function) key. The default setting ofthis key is None (no function). The programmable func-tions available for this key are listed below.
t keyPF (Programmable Function) key. The default setting ofthis key is Monitor. Other programmable functions avail-able for this key are listed below.
y 1/ 2/ 3/ 4 keysPress to select a channel from 1 to 4.
u Microphone jackInsert the microphone plug into this jack (the microphoneis an optional accessory).
i SpeakerInternal speaker.
o PTT switchPress this switch, then speak into the microphone to call astation.
1-2. Microphone
q w e tr
yu
i
o
1-3. Auxiliary Programmable Functions• Emergency • Scan On/OFF• Key Lock • Talk Around• Monitor • Temporary Delete• None (no function) • AUX• Horn Alert • Scan + Temporary Delete
1-4. Display
TK-7102H
5
2. Operation FeaturesThe TK-7102H is a VHF FM radio designed to operate in
conventional format. The programmable features are sum-marized.
3. Transceiver Controls and Indicators
3-1. Front Panel ControlsAll the keys on the front panel are momentary-type push
buttons. The functions of these keys are explained below.
• POWER keyTransceiver POWER key. When the power is switched
off, all the parameters are stored in memory. When thepower is switched on again, the transceiver returns to theprevious conditions.
• CHANNEL keys
• MONITOR key (Programmable)
• key (Programmable)
• VOLUME UP/DOWN keyWhen the key is pressed, the volume level is increased/
decreased and repeats if held for 200ms or longer.
• BUSY/TX LEDThe BUSY indicator (Green LED) shows that the channel is
in use. The TX indicator (Red LED) shows that you are trans-mitting.
3-2. Programmable KeysThe FPU (KPG-70D) enables programmable keys to select
the following functions.• Emergency• Key Lock• Monitor• Scan ON/OFF• Talk Around• Temporary Delete• None• AUX• Horn Alert• Scan + Temporary Delete
• EmergencyPressing this key for longer than 1 second causes the
transceiver to enter the emergency mode. The transceiverjumps to the programmed “Emergency channel” and trans-mits for 25* seconds.
The transceiver disables mic mute while transmitting. Af-ter finishing transmission, the transceiver receivers for 5*seconds. The transceiver Mute* the speaker while receiving.Following the above sequence, the transceiver continues totransmit and receive.* Default value.
• Key lockPressing this key causes the transceiver to accept entry of
only the [Vol Up/Down]*, [Key lock], Microphone [PTT],[Monitor], [Emergency], and [Power] keys.* Programmable
• MonitorUsed to release signalling (press once) or squelch (press
and hold for approximately two seconds) when operating as aconventional. It is also used to reset option signalling.
• Scan ON/OFFPress this key starts scanning. Pressing this key stops
scanning.
• Talk aroundPress this key, the transceiver uses the receive frequency
and the tone for transmission.The operator can call the other party directly (without re-
peater). Press this key again, the talk around function goesoff.
• Temporary deleteThe “Add” channel contained in the scan sequence, and
“Delete” channel is not contained. In the scan mode, thiskey switches the channel delete temporarily (Press and holdfor approximately one second).
When the transceiver is turned off, the transceiver exitsthe scan or switches the scan function off.
• NoneSounds error operation beep, and no action will occur.
Use this function when the transceiver is required to be moresimple operated.
• AUXPress to activate the auxiliary port. Press again to deacti-
vate the auxiliary port. Auxiliary is used with optional boards,allowing you to activate and deactivate these optional func-tions. While activated, the AUX icon appears on the display.
• Horn alertHorn Alert is a useful feature that will notify you of a re-
ceived call while you are away from your vehicle. The trans-ceiver is programmed to sound the vehicle horn or someother external alert device (such as the vehicle headlights)when a call is received that has correct signalling.
• Scan + Temporarily deleteTo temporarily remove a channel from the Scan list, press
and hold this key for approximately one second during Scan,while Scan is paused on the undesired channel, to tempo-rarily remove that channel from the scanning sequence. Af-ter switching the Scan function OFF, or switching the trans-ceiver OFF and then ON again, the Scan settings return tonormal.
OPERATING FEATURES
TK-7102H
6
4. Scan Operating
SCAN start conditionTwo or more channels must be added to all channels that
can be scanned. The transceiver must be in normal receivemode (PTT off).
When you activate the key programmed to the scan ON/OFF function, the scan starts. The indicator next to the pro-grammed key LED blinks.
Scan stop conditionThe scan stops temporarily if the following conditions are
satisfied.1) A carrier is detected, then QT/DQT matches on channels
for which receive the QT/DQT is set by the programmingsoftware.
2) A carrier is detected on the channels for which receivingQT/DQT is not set by the programming software or whenthe monitor (signalling cancel) function is activated.
Revert channelThe revert channel is used to transmit during scanning and
set by the programming software (KPG-70D).1) Selected channel
The transceiver reverts to the channel before scanning orthe channel that you changed during scan.
2) Selected with talkbackThe transceiver reverts to the selected channel prior toscan initiation.However, if a call is received on a channel other then theselected channel and PTT is pressed before scanning re-sume, the transceiver “talks back” on the current receivechannel.
Scan endWhen you press the key programmed to the scan function
during scan mode, the scan ends.The indicator next to the programmed key LED turns off.
Temporary deleteIt is possible to delete channel temporary during scan.
When scan stops on unnecessary channel for example by in-terference of the other party, activate the delete function (forexample press and hold the key for approximately one sec-ond), then that channel is deleted temporarily and scan re-start immediately.
The temporary deleted channels return to pre-set delete/add channels, when the transceiver is turned off or the scanfunction is switched off.
5. Details of Features
Time-out timerThe time-out timer can be programmed in 30 seconds in-
crements from 30 seconds to five minutes and off. If thetransmitter is transmitted continuously for longer than theprogrammed time, the transmitter is disabled and a warningtone sounds while the PTT button is held down. The warningtone stops when the PTT button is released.
PTT IDPTT ID provides a DTMF ANI or MSK ID to be sent with
every time PTT (connect ID at beginning of transmission, dis-connect ID at end of transmission, or both).
You can program PTT ID “on” or “off” for each groupchannel (DTMF). The contents of ID are programmed foreach transceiver.
The transceiver is capable to have ID. The format isDTMF. The timing that the transceiver sends ID is program-mable.
BOT : Connect ID is sent on beginning of transmission.EOT : Disconnect ID is sent on end of transmission.Both : Connect ID is sent on beginning of transmissionand disconnect ID is sent on end of transmission.There is also “PTT ID” setting for each channel.
Off hook decodeIf the Off hook decode function has been enabled, remov-
ing and replacing the microphone on the hook has no effectfor decoding QT/DQT and option signalling.
“TOT” pre-alertThe transceiver has “TOT” pre-alert timer. This param-
eter selects the time at which the transceiver generates“TOT” pre-alert tone before “TOT” is expired.
“TOT” will be expired when the selected time passesfrom a TOT pre-alert tone.
“TOT” re-key timeThe transceiver has “TOT” re-key timer. This timer is the
time you can not transmit after “TOT” exceeded. After“TOT” re-key time expired you can transmit again.
“TOT” reset timeThe transceiver has “TOT” reset timer. This timer is the
minimum wait time allowed during a transmission that willreset the “TOT” count.
“TOT” reset time causes the “TOT” to continue even af-ter PTT is released unless the “TOT” reset timer has expired.
Clear to transpondThe transceiver waits the transpond of DTMF if channel is
busy until channel open. This feature prevents the interfer-ence to other party.
6. Option Signalling (DTMF)Built-in DTMF decoder is available for option signalling.It is possible to use individual call, group call, Stun.If the option signalling matches, a predetermined action
will occur.If option signalling matches on a channel is set up with
option signalling, the channel LED will flash and option signal-ling will be released. The transpond or alert tone will sound.
While option signalling matches (or if option signalling isdeactivated when you are transmitting), you can mute orunmute QT/DQT/Carrier.
OPERATING FEATURES
TK-7102H
7
SP UnmuteYou can select the type of SP Unmute system for each
channel. The selection is as follows.Carrier, QT/DQT:Channel with this option will not check ID Code in order toopen its speaker.Carrier+DTMF, QT/DQT+DTMF:Channel that is set with this option will have to check forID Code in order to open its speaker.Default:Carrier, QT/DQT.
SP unmute Channel setting RX condition Speaker
QT/DQT DTMF condition
Carrier None None Carrier Sounds
Yes Carrier Sounds
Carrier+DTMF Sounds
Carrier+DTMF None Yes Carrier Not Sounds
Carrier+DTMF Sounds
QT/DQT Yes None Carrier Not Sounds
Carrier+QT/DQT Sounds
Yes Carrier Not Sounds
Carrier+QT/DQT Sounds
Carrier+QT/DQT+DTMF Sounds
Carrier+DTMF Not Sounds
QT/DQT+DTMF Yes Yes Carrier Not Sounds
Carrier+QT/DQT Not Sounds
Carrier+QT/DQT+DTMF Sounds
Carrier+DTMF Not Sounds
Note :When QT/DQT is not used, QT/DQT and QT/DQT+DTMF
can not be selected.When DTMF is not used, Carrier+DTMF and QT/
DQT+DTMF can not be selected.
Auto ResetIf option signalling matches a group set up with option sig-
nalling, option signalling is released. After matching optionsignalling, option signalling will temporarily reset automati-cally.
StunIf the stun code matches, a predetermined action will oc-
cur. Whether option signalling is activated or not, when stunmatches on any channel, the transceiver will become TX in-hibited or TX/RX inhibited. While stun is active, if the stuncode + “#” code is received, stun will deactivate.
When stun matches, transpond will function. Alert willnot be output.
7. Audible User Feedback TonesThe transceiver outputs various combinations of tones to
notify the user of the transceiver operating state.Refer to the help file on the KPG-70D, regarding the func-
tions that are not listed below.
Stun on toneWhen a stun code is received, transpond tone sounds.
Stun off toneWhen a stun release code is received, transpond tone
sounds.
Group call toneSounds when a group call with the correct DTMF option
signalling is received, repeats 7 times. You can select yes orno in the Alert tone level setting.
Individual call toneSounds when an individual call with the correct DTMF op-
tion signalling is received. You can select yes or no in theAlert tone level setting.
Key input error toneSounds when a key is pressed but that key cannot be
used. You can select yes or no for the optional feature'swarning tone.
Transpond toneSounds when an individual call with the correct DTMF op-
tion signalling is received. For group calls, only the grouptone will sound, not the transpond tone.
Pre alert toneSounds prior to the TOT TX inhibit activation. If TOT pre
alert is set, the tone sounds at the amount of time pro-grammed, before the TOT expires (TOT time – TOT pre alerttime = Pre alert tone sounding time). You can select yes orno for the optional feature’s warning tone.
Transmit protectionThe final FET is protected against heat while transmitting
by making the radio cuts down TX power when the tempera-ture of the final FET becomes higher than reference. Afterthat, if the temperature continue to rise, transmission isstopped. The final FET is also protected against over voltageby having the radio to check that the voltage of power supplyconnected to the radio is not higher than about 17V when theradio is turned on, otherwise it can not transmit. In bothcases when transmission is stopped, a beep will continue tosound until the PTT key is released.
OPERATING FEATURES
TK-7102H
8
1. Modes
User mode
PC mode Data program-ming mode
PC test mode PC tuning modeClone mode
Mode Function
User mode For normal use.
PC mode Used for communication between the
radio and PC (IBM compatible).
Data programming Used to read and write frequency data
mode and other features to and from the radio.
PC test mode Used to check the radio using the PC.
This feature is included in the FPU.
PC tuning mode Used to tune the radio using the PC.
Clone mode Used to transfer programming data from
one radio to another.
2. How to Enter Each Mode
Mode Operation
User mode Power ON
PC mode Received commands from PC
Clone mode [1]+Power ON (Two seconds)
3. PC Mode
3-1. PrefaceThe TK-7102H transceiver is programmed using a per-
sonal computer, a programming interface (KPG-46) and pro-gramming software (KPG-70D).
The programming software can be used with an IBM PCor compatible. Figure 1 shows the setup of an IBM PC forprogramming.
3-2. Connection Procedure1. Connect the TK-7102H to the personal computer with the
interface cable.2. When the Power is switched on, user mode can be en-
tered immediately. When the PC sends a command, theradio enters PC mode.When data is transmitted from transceiver, the red LEDblink.When data is received by the transceiver, the green LEDblink.In the PC mode, 4CH LEDs, [MON] LED and [] LED areturned on.
Notes :• The data stored in the personal computer must match
model type when it is written into the EEPROM.• Attach the interface cable, then change the TK-7102H to
PC mode.
3-3. KPG-46 Description
(PC programming interface cable : Option)The KPG-46 is required to interface the TK-7102H to the
computer. It has a circuit in its D-subconnector (25-pin) casethat converts the RS-232C logic level to the TTL level.
The KPG-46 connects the modular microphone jack of theTK-7102H to the computers RS-232C serial port.
3-4. Programming Software DescriptionThe KPG-70D programming disk is supplied in 3-1/2" disk
format. The software on this disk allows a user to programTK-7102H radio via a programming interface cable (KPG-46).
3-5. Programming With IBM PCIf data is transferred to the transceiver from an IBM PC
with the KPG-70D, the destination data (basic radio informa-tion) for each set can be modified.
Fig. 1
IMC-PC
KPG-46
KPG-70D
TK-7102H
REALIGNMENT
TK-7102H
9
4. Clone ModeProgramming data can be transferred from one radio to
another by connecting them via their modular microphonejacks. The operation is as follows (the transmit radio is themaster and the receive radio is the slave).
Note :Clone mode should enabled.
1. Turn the master TK-7102H power ON with the [1] key helddown. The TK-7102H [] LED is turned on.
2. Power on the slave TK-7102H.3. Connect the cloning cable (No. E30-3382-05) to the modu-
lar microphone jacks on the master and slave.4. Press the [] key on the master TK-7102H transceiver.
The data of the master is sent to the slave. While the mas-ter is sending data, [TX] LED blinked. While the slave isreceiving the data, 4 LEDs, [MON] LED, [] LED areturned on and [BUSY] LED blinked. When cloning of datais completed, the master [TX] LED turned off, and theslave automatically operates in the User mode. The slavecan then be operated by the same program as the master.
5. The other slave can be continuously cloned. Carry out theoperation in step 2 to 4.
4-1. Adding the data password.If the data password is set in the optional feature menu,
you must enter the password (Master transceiver) to activatea clone mode.
you can use 1, 2, 3, and 4 to configure the password. Themaximum length of the password is 10 digits.
1. [1]+Power ON.2. [1]~[4] LED, and MON LED are turned ON.3. Enter the password using [1]~[4] keys.4. Press [MON] key.5. If the password matches, the transceiver enters a clone
mode. Otherwise, transceiver beeps and returns to thepassword input mode.
Fig. 2
Clone cable(E30-3382-05)
REALIGNMENT
5. Accessory Connection Cable (KCT-39)The KCT-39 is an accessory connection cable for connect-
ing external equipment. The connector has 15 pins and thenecessary signal lines are selected for use.
5-1. Installing the KCT-39 in the Transceiver1. Lift the DC cord bushing ( 1 ) from the chassis. Peel the
pad as shown in Figure 3 ( 2 ).
1
2
3
4
Fig. 3
2. Stick the pad to the DC cord ( 3 ) and chassis ( 4 ), bothof which are supplied with the KCT-39.
Fig. 4
TK-7102H
10
CN2CN3
AB
7
8
6
5
Chassis
Chassis
Cushion
KCT-39sumi tube
PCB
Face down
Avoid forming the wiring towards the shielding cover closure area.
Wire harnessband (Stopper)
End view of this area
910
1315 1
3
3. Insert the KCT-39 cable ( 5 ) into the chassis ( 6 ). Thewire harness band ( 7 ) must be inside the chassis andface down.
4. Connect the KCT-39 to the TX-RX unit as shown in Figure5 ( 8 ).
5. Connect the KCT-39 to the external accessory by insertingthe crimp terminal ( 9 ) into the square plug ( 10 ), both ofwhich are supplied with the KCT-39.
Fig. 5
Fig. 6
1471013
2581114
3691215
No. Color Internal Name
connector
1 Red CN2-1 SB
2 Pink CN3-1 IGN
3 Black CN2-3 GND
4 Brown CN3-3 DETO
5 Orange CN3-2 DATAI
6 Yellow CN2-8 FNC4
7 Green CN2-7 FNC3
8 Blue CN2-9 FNC5
9 Purple CN2-12 FNC8
10 Gray CN2-10 FNC6
11 White CN2-11 FNC7
12 NC NC
13 NC NC
14 Sky blue CN2-6 FNC2
15 Turquoise CN2-5 FNC1
Accessory Port Function
REALIGNMENT
6. Ignition Sense Cable (KCT-18)The KCT-18 is an optional cable for enabling the ignition
function. The ignition function lets you turn the power to thetransceiver on and off with the car ignition key.
6-2. Connecting the KCT-18 to the Transceiver1. Install the KCT-39 in the transceiver. (See the KCT-39 sec-
tion)2. Insert the KCT-18 lead terminal ( 1 ) into pin 2 of the KCT-
39 ( 2 ).
Fig. 7
2
1
1315
1
3
TK-7102H
11
REALIGNMENT / INSTALLATION
6-3. Modifying the TransceiverModify the transceiver as follows to turn the power on and
off with the ignition key.
1. Remove the jumper resistor (0Ω) R71 of the TX-RX unit.
Setting With the KPG-70DSelect “External Devices” from the “Edit” menu and en-
able the “Ignition Sense”.
R71
CN
2
TX-RX UNITComponent side
Fig. 8
INSTALLATION
1. Optional Board
1-1. Voice Scrambler Board Connection
Modification1. Remove the cabinet and shielding cover from the trans-
ceiver.2. Delete R202 and R267 on the TX-RX unit.
A
9
87DCBA
A12
1
3
789
101112
1
12
BA11CA10DA9E12345B56B77A88A79A310B1111B912B4E18
Voice scramblerboard
12 pins lead wirewith connector (A)
E37-1081-05CN2
12
6
5
11
10
1
45
7
9
11
1
11
11 pins lead wirewith connector (B)
E37-1080-05CN3
R267
CN3
R202
TX-RX UNITComponent side
ConnectionThe functions of pins of CN2 and CN3 on the TX-RX unit
are shown in the TERMINAL FUNCTION section (page 34).
Fig. 1
Fig. 2
TK-7102H
12
Pins Connection
Voice scrambler 12 pins lead wire 11 pins lead wire
functions with connector (A) with connector (B)
A A-12 –
B A-11 –
C A-10 –
D A-9 –
5 – B-5
6 – B-7
7 A-8 –
8 A-7 –
9 A-3 –
10 – B-11
11 – B-9
12 – B-4
INSTALLATION
Setting With the KPG-70DSelect “External Devices” from the “Edit” menu and set
the “Scrambler”.
Note :The voice scrambler board is connected subsequent to thede-emphasis circuit.
Cushion (G13-1963-04)
Cushion (G13-1964-04)Voice scrambler board
Front side
to CN2 and CN3
to CN2and CN3
CN3
Voice scramblerboard
CN2
TX-RX UNITComponent side
Avoid forming the wiring towards shielding cover closure area.
1-2. Example for Connection
Picture (Trunking Board)
Fig. 3
Insulation sheet
Cushion D(G13-1972-04)
Cushion C Cushion B
Trunking board
TX-RX unitCN4
Front side
Setting With the KPG-70DSelect “External Devices” from the “Edit” menu and set
the “SmarTrunk”.
Fig. 4
TK-7102H
13
DISASSEMBLY FOR REPAIR
1. When you remove the panel, turn the transceiver up sidedown. Detach the panel by lifting the tabs as shown be-low.
Fig. 1
Fig. 2
2. To remove the cabinet, first turn the transceiver up sidedown. Detach the cabinet by prying the tabs as shownbelow.
3. To remove the display unit PCB, detach the PCB by liftingat the indents of the PCB as shown below.
Fig. 3
Fig. 5
5. When mounting the front panel, match the 4 tabs of thechassis with the panel, being sure they attach securely.
Tabs
Tabs
Tabs
Indents
Tabs
Tabs
4. Mount the display unitTo mount the display unit on the panel, follow the correctprocedures shown to ensure easy display unit assemblyand good fitting onto the panel.q Snap in bottom of display unit first.w Snap in top of displaly unit.
q
w
Fig. 4
TK-7102H
14
Frequency ConfigurationThe receiver utilizes double conversion. The first IF is
49.95MHz and the second IF is 450kHz. The first local oscil-lator signal is supplied from the PLL circuit.
The PLL circuit in the transmitter generates the necessaryfrequencies. Figure 1 shows the frequencies.
CIRCUIT DESCRIPTION
Receiver SystemThe receiver is double conversion superheterodyne. The
frequency configuration is shown in Figure 1.
Front-end RF AmplifierAn incoming signal from the antenna is applied to an RF
amplifier (Q353) after passing through a transmit/receiveswitch circuit (D603, D604, D605 are off) and a band passfilter (L357, L356 and varactor diodes : D353, D354). Afterthe signal is amplified (Q353), the signal is filtered through aband pass filter (L354, L355 and varactor diodes: D351,D352) to eliminate unwanted signals before it is passed tothe first mixer.
The voltage of these diodes are controlled by tracking theCPU (IC101) center frequency of the band pass filter. (SeeFig. 2)
First MixerThe signal from the RF amplifier is heterodyned with the
first local oscillator signal from the PLL frequency synthesizercircuit at the first mixer (Q352) to create a 49.95MHz firstintermediate frequency (1st IF) signal. The first IF signal isthen fed through one pair of monolithic crystal filter (MCF :XF351) to further remove spurious signals.
ANTSW
RFAMP
1stMIX
AFPA
TCXO
MICAMP
X3multiply
RFAMP
POWERAMP
CF 450kHz
MCF49.95MHz
IF SYSTEM
PLL/VCO
16.8MHz
50.4MHz
ANT
RX
TX
SP
MIC1/2
Fig. 1 Frequency configuration
IF AmplifierThe first IF signal is amplified by Q351, and the enters
IC301 (FM processing IC). The signal is heterodyned againwith a second local oscillator signal within IC301 to create a450kHz second IF signal. The second IF signal is then fedthrough a 450kHz ceramic filter (Wide : CF301, Narrow :CF302) to further eliminate unwanted signals before it is am-plified and FM detected in IC301.
Item Rating
Nominal center frequency 49.95MHz
Pass bandwidth ±5.0kHz or more at 3dB
35dB stop bandwidth ±20.0kHz or less
Ripple 1.0dB or less
Insertion loss 5.0dB or less
Guaranteed attenMuation 80dB or more at fo±1MHz
Spurious : 40dB or more within fo±1MHz
Terminal impedance 350Ω / 5.5pF
Table 1 Crystal filter (L71-0591-05) : XF351
Item Rating
Nominal center frequency 450kHz
6dB bandwidth ±6.0kHz or more
50dB bandwidth ±12.5kHz or less
Ripple 2.0dB or less
Insertion loss 6.0dB or less
Guaranteed attenuation 35.0dB or more within fo±100kHz
Terminal impedance 2.0kΩ
Table 2 Ceramic filter (L72-0993-05) : CF301
Item Rating
Nominal center frequency 450kHz
6dB bandwidth ±4.5kHz or more
50dB bandwidth ±10.0kHz or less
Ripple 2.0dB or less
Insertion loss 6.0dB or less
Guaranteed attenuation 60.0dB or more within fo±100kHz
Terminal impedance 2.0kΩ
Table 3 Ceramic filter (L72-0999-05) : CF302
ANTL357,356D353,354
BPFQ353
RF AMPQ351
IF AMPIC161
D/A CONVERTERQ352MIX
XF351MCFD602~605
ANTSW
IC161D/A
Q302X3 multiply
IC4021/2 divider
X401TCXO
IC301IF system
1st local OSC (VCO/PLL)
W/NO(EVOL2)
CF301 (Wide)
CF302 (Narrow)
TV
CPU
L354,355D351,352
BPF
Fig. 2 Receiver system
TK-7102H
15
Wide/Narrow Changeover CircuitThe Wide port (pin 65) and Narrow port (pin 64) of the CPU
is used to switch between ceramic filters. When the Wideport is high, the ceramic filter SW diodes (D303, D302) causeCF301 to turn on to receive a Wide signal.
When the Narrow port is high, the ceramic filter SW di-odes (D303, D302) cause CF302 to turn on to receive a Nar-row signal.
AF Signal SystemThe detection signal from IF IC (IC301) goes to D/A con-
verter (IC161) to adjust the gain and is output to AF filter(IC251) for characterizing the signal. The AF signal outputfrom IC251 and the DTMF signal, BEEP signal are summedand the resulting signal goes to the D/A converter (IC161).The AFO output level is adjusted by the D/A converter. Thesignal output from the D/A converter is input to the audiopower amplifier (IC252). The AF signal from IC252 switchesbetween the internal speaker and speaker jack (J1) output.
Squelch CircuitThe detection output from the FM IF IC (IC301) passes
through a noise amplifier (Q301) to detect noise. A voltage isapplied to the CPU (IC101). The CPU controls squelch ac-cording to the voltage (SQIN) level. The signal from the RSSIpin of IC301 is monitored. The electric field strength of thereceive signal can be known before the SQIN voltage is inputto the CPU, and the scan stop speed is improved.
NarrowIC101 64pin
IF_IN MIX_O
IC301IF System
CF302(Narrow)
CF301(Wide)
R32
0
R31
9
R317
R318
D303 D302
WideIC6 65pin
AFFilter
D/ACONV.
D/ACONV.
IC161 IC251 IC161W/NO(EVOL2)
AF PA
IC252 SP
IF IC
IC301
Q301NOISE AMP D301IC301 IC101
AFO
RSSI
DETCPUIF
SYSTEM
SQIN
RSSI
Fig. 3 Wide/Narrow changeover circuit
Fig. 4 AF signal system
Fig. 5 Squelch circuit
PLL Frequency SynthesizerThe PLL circuit generates the first local oscillator signal for
reception and the RF signal for transmission.
PLLThe frequency step of the PLL circuit is 5 or 6.25kHz. A
16.8MHz reference oscillator signal is divided at IC401 by afixed counter to produce the 5 or 6.25kHz reference fre-quency. The voltage controlled oscillator (VCO) output signalis buffer amplified by Q410, then divided in IC401 by a dual-module programmable counter. The divided signal is com-pared in phase with the 5 or 6.25kHz reference signal in thephase comparator in IC401. The output signal from thephase comparator is filtered through a low-pass filter andpassed to the VCO to control the oscillator frequency. (SeeFig. 6)
VCOThe operating frequency is generated by Q406 in transmit
mode and Q405 in receive mode. The oscillator frequency iscontrolled by applying the VCO control voltage, obtainedfrom the phase comparator, to the varactor diodes (D405 andD406 in transmit mode and D403 and D404 in receive mode).The TX/RX pin is set low in receive mode causing Q408 andQ407 to turn Q406 off, and turn Q405 on. The TX/RX pin isset high in transmit mode. The outputs from Q405 and Q406are amplified by Q410 and sent to the RF amplifiers.
D405,406
Q406TX VCO
Q410BUFFAMP
D403,404
Q405RX VCO
Q407,408T/R SW
Chargepump
LPF
Phasecomparator
1/M
1/N5kHz/6.25kHz
5kHz/6.25kHz
REFOSC
16.8MHz
PLLDATA
IC401 : PLL ICQ404AMP
Fig. 6 PLL circuit
CIRCUIT DESCRIPTION
TK-7102H
16
Unlock CircuitDuring reception, the 8RC signal goes high, the 8TC signal
goes low, and Q34 turns on. Q33 turns on and a voltage isapplied to the collector (8R). During transmission, the 8RCsignal goes low, the 8TC signal goes high and Q36 turns on.Q35 turns on and a voltage is applied to 8T.
The CPU in the control unit monitors the PLL (IC401) LDsignal directly. When the PLL is unlocked during transmis-sion, the PLL LD signal goes low. The CPU detects this sig-nal and makes the 8TC signal low. When the 8TC signal goeslow, no voltage is applied to 8T, and no signal is transmitted.
IC101CPU
Q34SW
Q33SW
IC401PLL
Q36SW
Q35SW
LD
8RC
8C
8R 8T
8TC
PLL lock: LD “H”
Fig. 7 Unlock circuit
Transmitter System
OutlineThe transmitter circuit produces and amplifies the desired
frequency directly. It FM-modulates the carrier signal bymeans of a varicap diode.
Power Amplifier CircuitThe transmit output signal from the VCO passes through
the transmission/reception selection diode (D409) and ampli-fied by Q501, Q502 and Q503. The amplified signal goes tothe final amplifier (Q504) through a low-pass filter. The low-pass filter removes unwanted high-frequency harmonic com-ponents, and the resulting signal is goes the antenna termi-nal.
APC CircuitThe automatic transmission power control (APC) circuit
detects part of a final amplifier output with a diode (D606,D607) and applies a voltage to IC501. IC501 compares theAPC control voltage (PC) generated by the D/A converter(IC161) and DC amplifier (IC203) with the detection outputvoltage. IC501 generates the voltage to control Q503 andQ504 and stabilizes transmission output.
The APC circuit is configured to protect over current ofQ503 and Q504 due to fluctuations of the load at the antennaend and to stabilize transmission output at voltage and tem-perature variations.
RFAMP
Q501
DRIVEAMP
Q503
FINALAMP
Q504PRE
DRIVEAMP
Q502
DCAMP
IC203
ANTSW
D602~D605
LPF
ANT
POWERDET
D606D607IC501
VR1APC
CONTROL
D409
PCIC161
3pin
Q411RF AMP2SC4649
(N,P)
Q501
RF AMP2SC3357
Q502PRE
DRIVE AMP2SC3357
Q503
ANT
DRIVE AMPPD55003TR
Q504FINAL AMPRD70HVF1
-01
IC4021/2
DIVIDERUPB1509GV
IC161 Q406D/A
CONVERTERM62363FP
X401
TCXO16.8MHz
VCO2SK508NV
(K52)
IC401
PLLMB15A02
Q410BUFFER2SC5108
(Y)
Q404RF AMP2SC4649
(N,P)
IC203
BUFFERNJM2902V
IC101
IC161
MIC KEYINPUT
CPU30622MAA
-B83GP
D/A CONVERTER
M62363FPIC161
D/A CONVERTER
M62363FP
IC203
SUM AMPNJM2902V
IC202IC201MIC
MIC/IDCNJM2100V
SplatterFILTER
NJM2904V
Fig. 9 APC circuit
Fig. 8 Transmitter system
CIRCUIT DESCRIPTION
TK-7102H
17
Control CircuitThe CPU carries out the following tasks:
1) Controls the WIDE, NARROW, TX/RX outputs.2) Adjusts the AF signal level of the AF filter (IC251) and
turns the filter select compounder on or off.3) Controls the display unit.4) Controls the PLL (IC401).5) Controls the D/A converter (IC161) and adjusts the vol-
ume, modulation and transmission power.
Memory CircuitThe transceiver has an 64k-bit EEPROM (IC66). The
EEPROM contains adjustment data. The CPU (IC101) con-trols the EEPROM through three serial data lines.
IC161D/A
converter
IC401PLL
IC101CPU
LDDTCK
PLLE
EEPCK
IC101CPU
IC66EEPROM
EEPDT
EEPWP
Display CircuitThe shift register controls the display LEDs through the CL
and DI lines from the CPU (IC101).When the transceiver is busy, LED G line becomes high
impedance, turning on Q4 and the green LED (D11) lights, intransmit mode, the LED R line becomes low impedance, andthe red LED (D12) lights.
Backlit LEDs (D1~D4) are provided and will only goes offwhen MBL line becomes low impedance.
When a function key (MON, PF, C1, C2, C3 or C4) is se-lected, its respective line becomes low impedance (LEDMON, LED PF, LED C1, LED C2, LED C3 or LED C4), theamber LED lights.
Key Matrix CircuitThe TK-7102H front panel has function keys. Each of
them is connected to a cross point of a matrix of the KMI1 toKMO2 ports of the microprocessor. The KMO1 to KMO2ports are always high, while the KMI1 to KMI4 ports are al-ways low.
The microprocessor monitors the status of the KMI1 toKMO2 ports. If the state of one of the ports changes, themicroprocessor assumes that the key at the matrix point cor-responding to that port has been pressed.
IC101CPU
KMI1KMI2KMI3
KMI4
KMO1KMO2
↑
↓
1
2
3P
M 4Fig. 10 Control circuit
Fig. 11 Memory circuit
Q4SW
Q10SW
Q9SW
IC101CPU
D1~D4
IC1Shift
register
CL LED MON
LED PF
LED C1
LED C2
LED C3
LED C4
LED R
LED G
MICBL
DI
D6
D5
D7
D8
D9
D10
D12
D11
Fig. 12 Display circuit
Fig. 13 Key matrix circuit
CIRCUIT DESCRIPTION
EncodeThe QT and DQT signals are output from QT/DQT of the
CPU (IC101) and summed with the external pin DI line by thesumming amplifier (IC203) and the resulting signal goes tothe D/A converter (IC161). The DTMF signal is output fromDTMF of the CPU and goes to the D/A converter (IC161). Thesignal is summed with a MIC signal by the summing amplifier(IC203), and the resulting signal goes to the D/A converter(IC161).
The D/A converter (IC161) adjusts the MO level and thebalance between the MO and QT/DQT levels. Part of a QT/DQT signal is summed with MO and the resulting signal goesto the VCOMOD pin of the VCO. This signal is applied to avaricap diode in the VCO for direct FM modulation.
X401TCXO
IC161D/A VCO
IC203SUMAMP
IC203SUMAMP
IC161D/A
IC401PLL
TCXOMOD
VCOMOD
HT
DI
QT/DQT
DTMF
IC101CPU
Fig. 14 Encodet
TK-7102H
18
Decode
• QT/DQT/DTMFThe signal (W/NO (EVOL2)) goes to SIGNAL (pin 88) of
CPU (IC101). The QT/DQT signal will pass through the low-pass filters in the CPU (IC101) and be decoded within theCPU (IC101). The DTMF signal will be decoded within theCPU (IC101).
D/A ConverterThe D/A converter (IC161) is used to adjust MO modula-
tion, AF volume, TV voltage, FC reference voltage, and PCPOWER CONTROL voltage level.
Adjustment values are sent from the CPU as serial data.The D/A converter has a resolution of 256 and the followingrelationship is valid:
D/A output = (Vin – VDAref) / 256 x n + VDArefVin: Analog inputVDAref: D/A reference voltagen: Serial data value from the microprocessor (CPU)
Power Supply CircuitWhen the power switch on the display unit is pressed, the
power port on the display unit which is connected port 17(POWER), goes low, then port 82 (SBC) goes high, Q32 turnson, SB SW (Q31) turns on and power (SB) is supplied to theradio.
When the DC power supplied to the radio, the voltageregulator IC (IC33) supply into the CPU VDD and reset voltagedetect IC (IC34). IC34 will generate signal (RESET) in to thereset terminal on the CPU (IC101) to carry out a power ONreset. Also, CPU (IC101) is checking on port 91 (Battery Volt-age). If DC power is less than about 9.5V, the radio is unableto power on.
When the DC power voltage deceases from normal volt-age, the INT voltage detector IC (IC35) will set to high on CPUport 18 (INT) if B line will became less than about 9.5V. ThenCPU send to EEPROM (IC66) the backup data and go intoSTOP mode.
This circuit has an overvoltage protection circuit. If a DCvoltage of 18V or higher is applied to the base of Q61, thisvoltage turns Q61 on and turns Q32 and SB off.
IC101CPU
SIGNAL W/NO (EVOL2)88
Q71SW
Q31SW
Q32SW
Q61SW
IC33AVR
D61
B
IC34RST
SBC
IGN
R77
R76
R39
R40
INT
5MBATT
IC101CPU
POWERSW
POWER
RE
SE
T
5M
IC35AVR
SB
IGN
Fig. 15 Decode
Fig. 16 Power supply circuit
CIRCUIT DESCRIPTION / SEMICONDUCTOR DATA
SEMICONDUCTOR DATA
Drive Amplifier : PD55003TR
(TX-RX Unit Q503)
Absolute Maximum Ratings (TCASE = 25°C)
Symbol Parameter Value Unit
V(BR)DSS Drain-Source voltage 40 V
VGS Gate-Source voltage ±20 V
ID Drain current 2.5 A
PDISS Power dissipation (@ Tc=70°C) 31.7 W
Tj Max. operating junction temperature 165 °C
TSTG Storage temperature –65 to +150 °C
TK-7102H
19
SEMICONDUCTOR DATA
Terminal Function
Pin No. Name I/O Function
1 QT/DQT O QT/DQT output.
2 DTMF/MSK O DTMF/MSK/BEEP output
3 PLLE O PLL IC chip select.
4,5 NC I
6 GND - GND.
7 CNVSS - DNVss for flash.
8 EVLLD O E-volume LD.
9 BSHIFT O Beat shift.
10 RESET - Reset.
11 XOUT - X’tal (14.318MHz).
12 VSS - GND.
13 XIN - X’tal (14.318MHz).
14 VCC - +5V.
15 GND - GND (Input only).
16 NC I
17 POWER I Power key input.
18 INT I µcom stop.
19 NC I
20 TX/RX O TX/RX.
21 UL O PLL unlock detect.
22~25 NC I
26 EEPWP O EEPROM write protect
27 EEPCK O EEPROM clock (N ch open drain).
28 EEPDT I/O EEPROM data (N ch open drain).
29 FNC1 I/O Function P1/TxD for flash.
30 FNC2 I/O Function P2/RxD for flash.
31 CLKFLS I SCLK for flash.
32 BSYFLS O Busy for flash.
33 TXD O To FPU.
34 RXD I From FPU.
35 PTT I PTT key.
36 HOOK I Hook.
37,38 NC I
39 EMPFLS I/O EPM for flash.
40~42 NC I
43 FNC3 I/O Function port 3.
44 CEFLS I/O CE for flash.
45,46 FNC4, FNC5 I/O Function port 4, 5
47,48 FNC7, FNC6 I/O Function port 7, 6.
49 FNC8 I/O Function port 8.
50 AFM O AF mute.
51 SPM O Speaker mute.
Pin No. Name I/O Function
52 AMPSW O AF AMP switch.
53 DT O Common data.
54 CK O Common clock.
55,56 NC I
57~59 DST1~DST3 I Destination 1~3
60 VCC - +5V.
61 NC I
62 VSS - GND.
63 NC I
64 NARROW O
65 WIDE O
66~68 NC I
69 CL O Clock for LCD.
70 CE O Chip enable for LCD.
71 DI O Transfer data to LCD.
72 IGN I Ignition.
73 MICMT1 O Mic 1 mute.
74 MICEM O Mic 2 mute.
75 MICMT2 O Mic 3 mute.
76 8RC O 8R control.
77 8TC O 8T control.
78 CM I/O Mic key check.
79~81 NC I
82 SBC O Battery switch.
83 KMI2 I Key matrix 2.
84 KMI1 I Key matrix 1.
85 KMI3 I Key matrix 3.
86 KMI4 I Key matrix 4.
87 NC I
88 SIGNAL I DTMF/QT/DQT input.
89 TEMP2 I Temperature 2.
90 TEMP1 I Temperature 1.
91 BATT I Battery voltage.
92 RSSI I RSSI input.
93 SQIN I Squelch input.
94 AVSS - GND.
95 NC I
96 VREF - +5V.
97 AVCC - +5V.
98 NC I
99 KMO1 O Key matrix output 1.
100 KMO2 O Key matrix output 2.
Microprocessor : 30622MAA-B83GP (TX-RX Unit IC101)
TK-7102H
20
Display Unit (X54-3460-20)
Ref. No. Parts name Description
IC1 IC Shift register for LED & MICBL control
Q4 Transistor Busy light switch
Q9,10 Transistor Key backlit switch
D1~4 LED Key backlit
D5 LED Monitor key light
D6 LED Programmable key light
D7~10 LED Channel key light
D11 LED Busy
D12 LED Transmit
D13 Diode Surge protection
TX-RX Unit (X57-6700-XX)
Ref. No. Parts name Description
IC31 IC Voltage regulator (8C)
IC32 IC Voltage regulator (5C)
IC33 IC Voltage regulator (5M)
IC34 IC Voltage detector reset
IC35 IC Voltage detector int
IC66 IC EEPROM
IC101 IC CPU
IC161 IC Digital potentiometer
IC201 IC MIC amplifier / IDC
IC202 IC MIC amplifier / Splatter filter
IC203 IC Buffer amplifier / SUM amplifier
/ DC amplifier / 1/2 Vcc
IC251 IC Audio filter
IC252 IC Audio amplifier
IC301 IC FM demodulation
IC401 IC PLL synthesizer
IC402 IC Divider (Hetero)
IC501 IC APC controller
Q1 FET TX AF
Q31,32 Transistor DC switch (SB) / Active when power is on
Q33,34 Transistor DC switch (8R) / Active while RX
Q35,36 Transistor DC switch (8T) / Active while TX
Q61 Transistor Over voltage detection / Active when
PS voltage is more than 18V
Q71 Transistor Ignition / Ignition sens
Q86,87 Transistor Beat shift / Active while beat shift is on
Q201 Transistor AF amplifier / MIC mute / Emergency MIC mute
Q202 FET Emergency MIC mute / Active when
MICEM is H
Q251 Transistor Buffer amplifier / RX audio
Q252,253 FET AF mute / Active while AFM is H
Ref. No. Parts name Description
Q254 Digital transistor AF mute / Active while SPM is H
Q255 Transistor AF mute / Active while AMPSW is H
Q301 Transistor Noise amplifier / SQL amplifier
Q302 Transistor Buffer amplifier / 16.8MHz 3rd over tone
Q351 Transistor IF amplifier
Q352 FET Mixer
Q353 FET RF amplifier / LNA
Q354 Transistor RF BPF
Q402,403 Transistor Charge pump
Q404 Transistor RF amplifier / PLL F in
Q405 FET RX VCO
Q406 FET TX VCO
Q407 FET T/R switch
Q408 Transistor T/R switch
Q410 Transistor Buffer amplifier / Output of VCO
Q411 Transistor RF amplifier / Output of VCO
Q440 Transistor Lipple filter
Q501,502 Transistor RF amplifier / Drive stage
Q503 FET RF amplifier / Drive amplifier
Q504 FET RF amplifier / Final amplifier
D1 Diode Surge absorption / CM
D2 Diode Surge absorption / HOOK
D3 Diode Surge absorption / PTT
D4~11 Diode Surge absorption / FNC1~8
D31 Diode Reverse connection protection
D32 Poly switch Current protection
D61 Diode Over voltage detection
D201 Diode OR gate / MIC mute, AGC
D202 Diode AGC
D251 Diode Limiter
D301 Diode Detection
D302,303 Diode IF switch (Wide/Narrow)
D351~354 Varicap RF BPF tuning
D401 Diode Lipple filter
D402 Diode Voltage dropped
D403,404 Varicap RX VCO
D405,406 Varicap TX VCO
D407 Varicap Modulation
D408 Diode Lipple filter
D409 Diode RF switch (TX/RX)
D501,502 Diode Temperature compensation
D503 Diode Voltage protection
D602~605 Diode ANT switch
D606,607 Diode APC voltage detect
D608 Diode Temperature compensation
COMPONENTS DESCRIPTION
TK-7102H
21
PARTS LIST New Parts. indicates safety critical components.Parts without Parts No. are not supplied.Les articles non mentionnes dans le Parts No. ne sont pas fournis.Teile ohne Parts No. werden nicht geliefert.
L : Scandinavia K : USA P : CanadaY : PX (Far East, Hawaii) T : England E : EuropeY : AAFES (Europe) X : Australia M : Other Areas
Ref. No. Address Parts No. Description Desti-nation
Newparts Ref. No. Address Parts No. Description Desti-
nationNewparts
TK-7102H
DISPLAY UNIT (X54-3460-20)
TX-RX UNIT (X57-6700-XX)
1 1B A01-2181-01 CABINET2 3B A10-4048-21 CHASSIS3 3A A62-0942-03 PANEL ASSY
5 3A B10-2753-03 FRONT GLASS8 1D B62-1596-10 INSTRUCTION MANUAL (ENGLISH)9 1D B62-1597-10 INSTRUCTION MANUAL (SPANISH)10 3B B72-2036-14 MODEL NAME PLATE K10 3B B72-2037-14 MODEL NAME PLATE K2
10 3B B72-2038-14 MODEL NAME PLATE M10 3B B72-2039-14 MODEL NAME PLATE M2
12 3B E04-0167-05 RF COAXIAL PECEPTACLE (M)14 3C E30-3339-05 DC CORD ACCESSORY15 2B E30-3448-05 DC CORD (RADIO)16 2A E37-1041-05 FLAT CABLE- E37-1080-05 FOR SCRAMBLER BOARD (B)
- E37-1081-05 FOR SCRAMBLER BOARD (A)19 3A E37-1082-05 SPEAKER CABLE
21 2B F10-2449-01 SHIELDING COVER22 3C F51-0017-05 FUSE (630) ACCESSORY
24 2B G02-0894-04 EARTH SPRING (FINAL FET)- G10-1274-04 FIBROUS SHEET (PANEL ASSY)25 3B G11-4127-14 RUBBER SHEET (CHASSIS)26 2B G11-4240-04 RUBBER SHEET (DRIVE FET)27 3B G13-1468-04 CUSHION (DC CORD)
28 3A G13-1836-04 CUSHION (SPEAKER)- G13-1963-04 CUSHION (SCRAMBLER BOARD)- G13-1964-04 CUSHION (SCRAMBLER BOARD)- G13-1972-04 CUSHION (TRUNKING BOARD)30 3A G53-1525-03 PACKING (PANEL)
31 2B G53-1542-03 PACKING (PHONE JACK)32 1B G53-1544-01 PACKING (CABINET)33 2A G53-1548-02 GASKET
35 2C,1D H12-3112-05 PACKING FIXTURE36 3D H13-1190-02 CARTON BOARD37 1D H25-2341-04 PROTECTION BAG38 2D H52-1829-22 ITEM CARTON CASE
40 3C J19-1584-05 HOLDER ACCESSORY K,K241 3D J29-0662-03 BRACKET ACCESSORY
43 3A K29-9065-01 KEY TOP
A 2B N67-2608-46 PAN HEAD SEMS SCREW WB 2B,3B N87-2606-46 BRAZIER HEAD TAPTITE SCREWC 1B,2B N87-2614-46 BRAZIER HEAD TAPTITE SCREW45 3C N99-0395-05 SCREW SET ACCESSORY
47 3A T07-0739-05 SPEAKER48 2C T91-0624-05 MICROPHONE ACCESSORY K,K2
D1-4 B30-2238-05 LED (Y)D5-10 B30-2239-05 LED (SY)
D11 B30-2237-05 LED (YG)D12 B30-2240-05 LED (SR)
C4 CK73GB1H103K CHIP C 0.010UF KC8-17 CK73GB1H103K CHIP C 0.010UF KC18 CK73GB1A105K CHIP C 1.0UF KC25 CK73GB1H103K CHIP C 0.010UF KC27 CK73GB1C104K CHIP C 0.10UF K
CN1 E40-6005-05 FLAT CABLE CONNECTORJ1 E08-0877-05 MODULAR JACK
L1 L92-0138-05 FERRITE CHIP
CP3,4 RK75GB1J392J CHIP-COM 3.9K J 1/16WR1-6 RK73GB1J102J CHIP R 1.0K J 1/16WR7-15 RK73FB2A272J CHIP R 2.7K J 1/10WR16 RK73GB1J101J CHIP R 100 J 1/16WR17 RK73GB1J100J CHIP R 10 J 1/16W
R18 RK73GB1J472J CHIP R 4.7K J 1/16WR19,20 RK73GB1J222J CHIP R 2.2K J 1/16W
D13 DA221 DIODEIC1 BU2090FS MOS ICQ4 KRC102S DIGITAL TRANSISTORQ9 KRA225S DIGITAL TRANSISTORQ10 KRC102S DIGITAL TRANSISTOR
C10 CK73GB1H102K CHIP C 1000PF KC13-26 CK73GB1H471K CHIP C 470PF KC28 CK73GB1H221K CHIP C 220PF KC29 CK73GB1H471K CHIP C 470PF KC30 CK73GB1H102K CHIP C 1000PF K
C33 CK73GB1H102K CHIP C 1000PF KC34 C92-0721-05 CHIP-ELE 330UF 25WVC35-38 CK73GB1H102K CHIP C 1000PF KC39,40 CK73GB1C104K CHIP C 0.10UF KC41 C92-0795-05 CHIP-TAN 22UF 10WV
C42 CK73GB1H103K CHIP C 0.010UF KC43-45 C92-0795-05 CHIP-TAN 22UF 10WVC49,50 CK73GB1H103K CHIP C 0.010UF KC51 C92-0560-05 CHIP-TAN 10UF 6.3WVC52,53 CK73GB1H102K CHIP C 1000PF K
C54,55 CK73GB1C104K CHIP C 0.10UF KC56 CK73GB1H102K CHIP C 1000PF KC61 CK73GB1H102K CHIP C 1000PF KC66 CK73GB1H102K CHIP C 1000PF KC72 CK73GB1H102K CHIP C 1000PF K
C77,78 CK73GB1H102K CHIP C 1000PF KC82 CK73GB1H102K CHIP C 1000PF KC83 CK73GB1C104K CHIP C 0.10UF KC87 CC73GCH1H180J CHIP C 18PF JC88,89 CC73GCH1H060B CHIP C 6.0PF B
C90 CC73GCH1H180J CHIP C 18PF JC97,98 CK73GB1H102K CHIP C 1000PF KC101 CK73GB1H102K CHIP C 1000PF KC102 CK73GB1C104K CHIP C 0.10UF K
TK-7102H
DISPLAY UNIT (X54-3460-20)
TX-RX UNIT (X57-6700-XX) -22 : M -23 : M2 -24 : K -25 : K2
TK-7102H
22
PARTS LIST
Ref. No. Address Parts No. Description Desti-nation
Newparts Ref. No. Address Parts No. Description Desti-
nationNewparts
TX-RX UNIT (X57-6700-XX)
C103 CK73GB1H102K CHIP C 1000PF KC104 CK73GB1C104K CHIP C 0.10UF KC151 CK73GB1H182K CHIP C 1800PF KC152 CK73GB1H392K CHIP C 3900PF KC161 CK73GB1H102K CHIP C 1000PF K
C162 C92-0507-05 CHIP-TAN 4.7UF 6.3WVC163 CK73GB1H102K CHIP C 1000PF KC164 C92-0560-05 CHIP-TAN 10UF 6.3WVC201 CK73GB1C104K CHIP C 0.10UF KC202 CK73GB1H102K CHIP C 1000PF K
C203 CK73GB1C273K CHIP C 0.027UF KC204 C92-0514-05 CHIP-TAN 2.2UF 10WVC205 CK73GB1C104K CHIP C 0.10UF KC206 CK73GB1H102K CHIP C 1000PF KC207 CK73GB1C223K CHIP C 0.022UF K
C208 CK73GB1H103K CHIP C 0.010UF KC210 CK73GB1C104K CHIP C 0.10UF KC211 CK73GB1H821K CHIP C 820PF KC212 CK73GB1H122K CHIP C 1200PF KC213 CK73GB1H332K CHIP C 3300PF K
C214 CC73GCH1H151J CHIP C 150PF JC215 CK73GB1C104K CHIP C 0.10UF KC217,218 C92-0560-05 CHIP-TAN 10UF 6.3WVC220 C92-0507-05 CHIP-TAN 4.7UF 6.3WVC221 CK73GB1C104K CHIP C 0.10UF K
C225 C92-0004-05 CHIP-TAN 1.0UF 16WVC226 CK73GB1H472K CHIP C 4700PF KC227 CK73GB1E103K CHIP C 0.010UF KC228 C92-0560-05 CHIP-TAN 10UF 6.3WVC229 C92-0507-05 CHIP-TAN 4.7UF 6.3WV
C230 CK73GB1C104K CHIP C 0.10UF KC231,232 CK73GB1H102K CHIP C 1000PF KC233 C92-0507-05 CHIP-TAN 4.7UF 6.3WVC250 CK73GB1C104K CHIP C 0.10UF KC251 C92-0714-05 CHIP-TAN 4.7UF 6.3WV
C252 CC73GCH1H390J CHIP C 39PF JC253,254 CK73GB1A105K CHIP C 1.0UF KC255 CK73GB1H822K CHIP C 8200PF KC256 CK73GB1E183K CHIP C 0.018UF KC257 CK73GB1C393K CHIP C 0.039UF K
C258-261 CK73GB1H103J CHIP C 0.010UF JC262 CK73GB1H102K CHIP C 1000PF KC263,264 CK73GB1C333K CHIP C 0.033UF KC265,266 CK73GB1C104K CHIP C 0.10UF KC267 CK73GB1A474K CHIP C 0.47UF K
C268 CK73GB1C104K CHIP C 0.10UF KC269 CK73GB1A105K CHIP C 1.0UF KC270 C92-0507-05 CHIP-TAN 4.7UF 6.3WVC271 CK73GB1H332K CHIP C 3300PF KC272 CK73GB1H102K CHIP C 1000PF K
C273 CK73GB1A105K CHIP C 1.0UF KC274 CK73FB1C224K CHIP C 0.22UF KC275 CK73GB1A105K CHIP C 1.0UF KC276,277 CK73GB1H102K CHIP C 1000PF KC278 CK73GB1C104K CHIP C 0.10UF K
C279 C92-0516-05 CHIP-TAN 4.7UF 16WVC280 C92-0040-05 CHIP-ELE 47UF 16WVC281 CK73GB1H102K CHIP C 1000PF KC282 C92-0722-05 CHIP-ELE 470UF 16WVC283 CK73GB1H102K CHIP C 1000PF K
C301 C92-0507-05 CHIP-TAN 4.7UF 6.3WVC302 CK73GB1H102K CHIP C 1000PF KC303 CK73GB1H472K CHIP C 4700PF KC304,305 CC73GCH1H331J CHIP C 330PF J K,MC304,305 CC73GCH1H391J CHIP C 390PF J K2,M2
C306 CK73GB1H102K CHIP C 1000PF KC307 CK73GB1E223K CHIP C 0.022UF KC308 CK73GB1H102K CHIP C 1000PF KC309 CK73GB1E223K CHIP C 0.022UF KC310 CK73FB1C334K CHIP C 0.33UF K
C311,312 CK73GB1C104K CHIP C 0.10UF KC313 C92-0662-05 CHIP-TAN 15UF 6.3WVC314 CK73GB1H103K CHIP C 0.010UF KC315-318 CK73GB1C104K CHIP C 0.10UF KC319 CC73GCH1H101J CHIP C 100PF J
C322 CC73GCH1H560J CHIP C 56PF JC323 CC73GCH1H271J CHIP C 270PF JC324 CK73GB1H103K CHIP C 0.010UF KC326 CK73GB1H103K CHIP C 0.010UF KC350 CK73GB1H471K CHIP C 470PF K
C351 CC73GCH1H330J CHIP C 33PF JC353 CK73GB1H103K CHIP C 0.010UF KC355 CC73GCH1H150J CHIP C 15PF JC357 CK73GB1H103K CHIP C 0.010UF KC358 CK73GB1H102K CHIP C 1000PF K
C359 CC73GCH1H080B CHIP C 8.0PF BC360-362 CK73GB1H102K CHIP C 1000PF KC363 CK73GB1H103K CHIP C 0.010UF KC364 CK73GB1H102K CHIP C 1000PF KC366 CK73GB1C104K CHIP C 0.10UF K
C367 CC73GCH1H101J CHIP C 100PF J K,MC367 CC73GCH1H151J CHIP C 150PF J K2,M2C368 CC73GCH1H220J CHIP C 22PF JC369 CC73GCH1H0R5B CHIP C 0.5PF B K2,M2C369 CC73GCH1H040B CHIP C 4.0PF B K,M
C370 CK73GB1H102K CHIP C 1000PF KC371 CC73GCH1H020B CHIP C 2.0PF BC372 CK73GB1H102K CHIP C 1000PF KC373 CC73GCH1H040B CHIP C 4.0PF B K,MC374 CC73GCH1H220J CHIP C 22PF J
C375-380 CK73GB1H102K CHIP C 1000PF KC382 CC73GCH1H220J CHIP C 22PF JC383 CK73GB1H102K CHIP C 1000PF KC384 CC73GCH1H010B CHIP C 1.0PF BC386 CC73GCH1H240J CHIP C 24PF J K,M
C386 CC73GCH1H270J CHIP C 27PF J K2,M2C387 CK73GB1H102K CHIP C 1000PF KC388 CC73GCH1H040B CHIP C 4.0PF B K,MC388 CC73GCH1H060B CHIP C 6.0PF B K2,M2C389 CK73GB1H102K CHIP C 1000PF K
C401-403 CC73GCH1H101J CHIP C 100PF JC404 C92-0662-05 CHIP-TAN 15UF 6.3WVC406 CK73GB1H102K CHIP C 1000PF KC408 CC73GCH1H220J CHIP C 22PF JC409 CK73GB1C104K CHIP C 0.10UF K
C410 C92-0560-05 CHIP-TAN 10UF 6.3WVC411 CK73GB1C104K CHIP C 0.10UF KC412 C92-0560-05 CHIP-TAN 10UF 6.3WVC413 CK73GB1H103K CHIP C 0.010UF KC414 CK73GB1C104K CHIP C 0.10UF K
TK-7102H
23
PARTS LIST
Ref. No. Address Parts No. Description Desti-nation
Newparts Ref. No. Address Parts No. Description Desti-
nationNewparts
TX-RX UNIT (X57-6700-XX)
C416-418 CK73GB1H102K CHIP C 1000PF KC421,422 CK73GB1H471K CHIP C 470PF KC423 C92-0555-05 CHIP-TAN 0.047UF 35WVC424 C92-0004-05 CHIP-TAN 1.0UF 16WVC425 C92-0001-05 CHIP C 0.1UF 35WV
C426 CC73GCH1H120J CHIP C 12PF J K2,M2C426 CC73GCH1H270J CHIP C 27PF J K,MC427 CC73GCH1H040B CHIP C 4.0PF B K2,M2C427 CC73GCH1H080B CHIP C 8.0PF B K,MC428 CK73GB1H471K CHIP C 470PF K
C429 CC73GCH1H010B CHIP C 1.0PF B K,MC429 CC73GCH1H020B CHIP C 2.0PF B K2,M2C430,431 CC73GCH1H050B CHIP C 5.0PF BC432 CC73GCH1H0R5B CHIP C 0.5PF BC434 CC73GCH1H330J CHIP C 33PF J K2,M2
C434 CK73GB1H471K CHIP C 470PF K K,MC435 CC73GCH1H050B CHIP C 5.0PF B K2,M2C435 CC73GCH1H100C CHIP C 10PF C K,MC436 CC73GCH1H0R5B CHIP C 0.5PF BC437 CK73GB1H471K CHIP C 470PF K
C438 CC73GCH1H020B CHIP C 2.0PF BC439 CC73GCH1H060B CHIP C 6.0PF B K,MC439,440 CC73GCH1H060B CHIP C 6.0PF B K2,M2C440 CC73GCH1H070B CHIP C 7.0PF B K,MC441 CC73GCH1H0R5B CHIP C 0.5PF B
C442 C92-0560-05 CHIP-TAN 10UF 6.3WVC444 CK73GB1H471K CHIP C 470PF KC448,449 CK73GB1H471K CHIP C 470PF KC450 C92-0568-05 CHIP-TAN 22UF 10WVC451,452 CK73GB1H471K CHIP C 470PF K
C453 CK73GB1H221K CHIP C 220PF KC454 CC73GCH1H060B CHIP C 6.0PF BC455 CC73GCH1H030B CHIP C 3.0PF BC456 CC73GCH1H020B CHIP C 2.0PF BC457 CK73GB1H102K CHIP C 1000PF K
C458 CK73GB1H221K CHIP C 220PF KC459 CK73GB1H102K CHIP C 1000PF KC460 CC73GCH1H180J CHIP C 18PF JC461 CK73GB1H102K CHIP C 1000PF KC462 CC73GCH1H100C CHIP C 10PF C
C463,464 CK73GB1H102K CHIP C 1000PF KC465 CC73GCH1H220J CHIP C 22PF JC466 CC73GCH1H101J CHIP C 100PF JC467 CK73GB1H102K CHIP C 1000PF KC468 CK73GB1H221K CHIP C 220PF K
C471 CC73GCH1H100C CHIP C 10PF C K,MC471 CC73GCH1H120J CHIP C 12PF J K2,M2C501,502 CK73GB1H102K CHIP C 1000PF KC503 CC73GCH1H101J CHIP C 100PF JC504-507 CK73GB1H102K CHIP C 1000PF K
C509 CC73GCH1H150J CHIP C 15PF JC510 CC73GCH1H080B CHIP C 8.0PF BC511-514 CK73GB1H102K CHIP C 1000PF KC515 CC73GCH1H270J CHIP C 27PF JC516 CK73GB1H821K CHIP C 820PF K
C517 CC73GCH1H030B CHIP C 3.0PF BC518 CC73GCH1H330J CHIP C 33PF JC519 CC73GCH1H820J CHIP C 82PF JC522 CK73FB1H102K CHIP C 1000PF KC525 CK73GB1H102K CHIP C 1000PF K
C526 CK73GB1H681K CHIP C 680PF KC527 CK73GB1H102K CHIP C 1000PF KC528 CK73GB1H221K CHIP C 220PF KC529 CK73FB1H102K CHIP C 1000PF KC530 CK73FB1C474K CHIP C 0.47UF K
C531 C92-0719-05 CHIP-ELE 47UF 25WVC533 C93-0570-05 CHIP C 68PF J K,MC533 C93-0572-05 CHIP C 100PF J K2,M2C536 CK73FB1H102K CHIP C 1000PF KC541,542 CM73F2H270J CHIP C 27PF J K,M
C545 C93-0603-05 CHIP C 1000PF KC546 CK73FB1C474K CHIP C 0.47UF KC549 CM73F2H221J CHIP C 220PF JC550 CM73F2H680J CHIP C 68PF JC552 C93-0564-05 CHIP C 22PF J K2,M2
C552,553 C93-0562-05 CHIP C 15PF J K,MC553 C93-0550-05 CHIP C 1.0PF C K2,M2C554 C93-0603-05 CHIP C 1000PF KC555 C93-0555-05 CHIP C 5.0PF CC556 C93-0603-05 CHIP C 1000PF K
C557,558 CK73GB1H103K CHIP C 0.010UF KC559 CK73GB1C104K CHIP C 0.10UF KC560 CK73GB1H102K CHIP C 1000PF KC574 CK73GB1H102K CHIP C 1000PF KC576 CK73GB1H221K CHIP C 220PF K
C601 CC73GCH1H120J CHIP C 12PF J K,MC601 CC73GCH1H180J CHIP C 18PF J K2,M2C602 C93-0555-05 CHIP C 5.0PF CC603 C93-0603-05 CHIP C 1000PF KC605 C93-0564-05 CHIP C 22PF J K,M
C605 C93-0566-05 CHIP C 33PF J K2,M2C606 CC73GCH1H0R5B CHIP C 0.5PF BC607 CC73GCH1H020B CHIP C 2.0PF BC608 C93-0566-05 CHIP C 33PF JC610 CC73GCH1H0R5B CHIP C 0.5PF B
C611 CC73GCH1H020B CHIP C 2.0PF BC613 C93-0566-05 CHIP C 33PF JC615 C93-0564-05 CHIP C 22PF JC616,617 CK73GB1H102K CHIP C 1000PF KTC351 C05-0399-05 CERAMIC TRIMMER CAP (6PF)
TC352 C05-0245-05 CERAMIC TRIMMER CAP (10PF)TC401,402 C05-0245-05 CERAMIC TRIMMER CAP (10PF)
J1 E11-0425-05 3.5D PHONE JACK (3P)CN1 E40-6268-05 FLAT CABLE CONNECTORCN2 E40-5702-05 PIN ASSYCN3 E40-6292-05 PIN ASSYCN4 E40-5932-05 PIN ASSY SOCKET
CN5 E40-3246-05 PIN ASSYCN601 E23-0486-05 TERMINAL
F501 F53-0108-05 FUSE (1.8A/50V)
CF301 L72-0993-05 CERAMIC FILTERCF302 L72-0999-05 CERAMIC FILTERL101 L92-0443-05 FERRITE CHIPL201 L92-0443-05 FERRITE CHIPL301 L34-4554-05 COIL
L302 L41-3385-08 SMALL FIXED INDUCTORL303,304 L40-3381-86 SMALL FIXED INDUCTOR (0.33UH)L351 L41-8285-08 SMALL FIXED INDUCTOR
TK-7102H
24
PARTS LIST
Ref. No. Address Parts No. Description Desti-nation
Newparts Ref. No. Address Parts No. Description Desti-
nationNewparts
TX-RX UNIT (X57-6700-XX)
L352 L41-5685-08 SMALL FIXED INDUCTORL354-356 L34-4612-05 AIR-CORE COIL K,ML354-356 L34-4613-05 AIR-CORE COIL K2,M2L357 L34-4611-05 AIR-CORE COILL401 L92-0443-05 FERRITE CHIP
L403 L41-1005-08 SMALL FIXED INDUCTORL404 L92-0442-05 FERRITE CHIPL405 L92-0443-05 FERRITE CHIPL406,407 L40-2702-86 SMALL FIXED INDUCTOR (27UH) K,ML406,407 L40-2785-92 SMALL FIXED INDUCTOR (270NH) K2,M2
L408 L40-2778-67 SMALL FIXED INDUCTOR (27NH) K,ML408 L40-3978-67 SMALL FIXED INDUCTOR (39NH) K2,M2L409-412 L40-2702-86 SMALL FIXED INDUCTOR (27UH) K,ML409-412 L40-2785-92 SMALL FIXED INDUCTOR (270NH) K2,M2L413 L40-3978-67 SMALL FIXED INDUCTOR (39NH) K,M
L413 L40-6878-67 SMALL FIXED INDUCTOR (68NH) K2,M2L414 L40-2785-92 SMALL FIXED INDUCTOR (270NH) K2,M2L414,415 L40-4791-86 SMALL FIXED INDUCTOR (4.7UH) K,ML415 L40-1085-92 SMALL FIXED INDUCTOR (100NH) K2,M2L416,417 L92-0443-05 FERRITE CHIP
L418 L40-6875-92 SMALL FIXED INDUCTOR (68NH) K2,M2L418 L41-3375-06 SMALL FIXED INDUCTOR K,ML419 L41-1085-06 SMALL FIXED INDUCTORL420 L41-1585-06 SMALL FIXED INDUCTORL421 L41-1085-06 SMALL FIXED INDUCTOR
L422 L41-5675-06 SMALL FIXED INDUCTORL501,502 L41-6875-08 SMALL FIXED INDUCTORL503,504 L41-2775-06 SMALL FIXED INDUCTORL505 L34-4606-05 AIR-CORE COIL K,ML505 L34-4645-05 AIR-CORE COIL K2,M2
L506 L34-4693-05 AIR-CORE COILL507 L34-4732-05 AIR-CORE COILL508 L34-4669-05 AIR-CORE COILL509 L34-4667-05 AIR-CORE COILL601 L34-4668-05 AIR-CORE COIL
L602-604 L34-4670-05 AIR-CORE COILL605 L34-4667-05 AIR-CORE COILX86 L77-1934-05 CRYSTAL RESONATOR (14.31818MHZ)X401 L77-1868-15 TCXO (16.8MHZ)XF351 L71-0591-05 MCF (49.95MHZ)
R1 RK73GB1J101J CHIP R 100 J 1/16WR2 R92-1252-05 CHIP R 0 OHM J 1/16WR3 RK73GB1J102J CHIP R 1.0K J 1/16WR4 RK73GB1J332J CHIP R 3.3K J 1/16WR5 RK73GB1J223J CHIP R 22K J 1/16W
R31 RK73GB1J472J CHIP R 4.7K J 1/16WR32 R92-1215-05 CHIP R 470 J 1/2WR33 RK73GB1J473J CHIP R 47K J 1/16WR34 RK73GB1J472J CHIP R 4.7K J 1/16WR35 RK73GB1J473J CHIP R 47K J 1/16W
R36 RK73GB1J152J CHIP R 1.5K J 1/16WR37 R92-1252-05 CHIP R 0 OHM J 1/16WR38 RK73GB1J334J CHIP R 330K J 1/16WR39 RK73GB1J474J CHIP R 470K J 1/16WR40 RK73GB1J394J CHIP R 390K J 1/16W
R41 RK73GB1J334J CHIP R 330K J 1/16WR61 RK73GB1J471J CHIP R 470 J 1/16WR62 RK73GB1J102J CHIP R 1.0K J 1/16WR66,67 RK73GB1J473J CHIP R 47K J 1/16WR68,69 RK73GB1J102J CHIP R 1.0K J 1/16W
R70 RK73GB1J473J CHIP R 47K J 1/16WR71 RK73GB1J472J CHIP R 4.7K J 1/16WR72 RK73GB1J105J CHIP R 1.0M J 1/16WR73 RK73GB1J104J CHIP R 100K J 1/16WR74 RK73GB1J473J CHIP R 47K J 1/16W
R75 RK73GB1J102J CHIP R 1.0K J 1/16WR76 RK73GH1J183D CHIP R 18K D 1/16WR77 RK73GH1J134D CHIP R 130K D 1/16WR78 RK73GB1J102J CHIP R 1.0K J 1/16WR81 RK73GB1J473J CHIP R 47K J 1/16W
R82 R92-1252-05 CHIP R 0 OHM J 1/16WR86 R92-1252-05 CHIP R 0 OHM J 1/16WR87 RK73GB1J102J CHIP R 1.0K J 1/16WR91,92 RK73GB1J102J CHIP R 1.0K J 1/16WR93,94 RK73GB1J562J CHIP R 5.6K J 1/16W
R101,102 RK73GB1J473J CHIP R 47K J 1/16WR103-106 RK73GB1J102J CHIP R 1.0K J 1/16WR107,108 RK73GB1J473J CHIP R 47K J 1/16WR109 RK73GB1J152J CHIP R 1.5K J 1/16WR110 RK73GB1J473J CHIP R 47K J 1/16W
R111 RK73GB1J102J CHIP R 1.0K J 1/16WR112,113 RK73GB1J473J CHIP R 47K J 1/16WR114-119 RK73GB1J102J CHIP R 1.0K J 1/16WR120-123 R92-1252-05 CHIP R 0 OHM J 1/16WR124 RK73GB1J473J CHIP R 47K J 1/16W
R125-128 RK73GB1J102J CHIP R 1.0K J 1/16WR129 R92-1252-05 CHIP R 0 OHM J 1/16WR130,131 RK73GB1J102J CHIP R 1.0K J 1/16WR151 RK73GB1J103J CHIP R 10K J 1/16WR152 RK73GB1J472J CHIP R 4.7K J 1/16W
R161 RK73GB1J122J CHIP R 1.2K J 1/16WR162 RK73GB1J152J CHIP R 1.5K J 1/16WR163 RK73GB1J473J CHIP R 47K J 1/16WR164-166 RK73GB1J102J CHIP R 1.0K J 1/16WR201 RK73GB1J681J CHIP R 680 J 1/16W
R202 R92-0670-05 CHIP R 0 OHMR203 RK73GB1J104J CHIP R 100K J 1/16WR204 RK73GB1J183J CHIP R 18K J 1/16WR205 RK73GB1J821J CHIP R 820 J 1/16WR206 RK73GB1J101J CHIP R 100 J 1/16W
R207 RK73GB1J754J CHIP R 750K J 1/16WR208 RK73GB1J152J CHIP R 1.5K J 1/16WR209 RK73GB1J244J CHIP R 240K J 1/16WR210 RK73GB1J183J CHIP R 18K J 1/16WR211,212 RK73GB1J823J CHIP R 82K J 1/16W
R213 RK73GB1J334J CHIP R 330K J 1/16WR214,215 RK73GB1J683J CHIP R 68K J 1/16WR216 RK73GB1J274J CHIP R 270K J 1/16WR217 RK73GB1J224J CHIP R 220K J 1/16WR218 RK73GB1J823J CHIP R 82K J 1/16W
R219 RK73GB1J184J CHIP R 180K J 1/16WR220,221 RK73GH1J153D CHIP R 15K D 1/16WR222 RK73GB1J102J CHIP R 1.0K J 1/16WR223 RK73GB1J472J CHIP R 4.7K J 1/16WR224 RK73GB1J102J CHIP R 1.0K J 1/16W
R225 RK73GB1J154J CHIP R 150K J 1/16WR226 RK73GB1J104J CHIP R 100K J 1/16WR227 RK73GB1J223J CHIP R 22K J 1/16WR228 RK73GB1J103J CHIP R 10K J 1/16WR229 RK73GB1J684J CHIP R 680K J 1/16W
TK-7102H
25
PARTS LIST
Ref. No. Address Parts No. Description Desti-nation
Newparts Ref. No. Address Parts No. Description Desti-
nationNewparts
TX-RX UNIT (X57-6700-XX)
R230 RK73GB1J124J CHIP R 120K J 1/16WR231 RK73GB1J683J CHIP R 68K J 1/16WR232 RK73GB1J912J CHIP R 9.1K J 1/16WR233 RK73GB1J682J CHIP R 6.8K J 1/16WR249-251 RK73GB1J473J CHIP R 47K J 1/16W
R252 RK73GB1J474J CHIP R 470K J 1/16WR253 R92-1252-05 CHIP R 0 OHM J 1/16WR254 RK73GB1J681J CHIP R 680 J 1/16WR255,256 RK73GB1J562J CHIP R 5.6K J 1/16WR257 RK73GB1J105J CHIP R 1.0M J 1/16W
R258 RK73GB1J272J CHIP R 2.7K J 1/16WR259 RK73GB1J123J CHIP R 12K J 1/16WR260 RK73GB1J224J CHIP R 220K J 1/16WR261 RK73GB1J124J CHIP R 120K J 1/16WR262 RK73GB1J183J CHIP R 18K J 1/16W
R263 RK73GH1J913D CHIP R 91K D 1/16WR264 RK73GH1J124D CHIP R 120K D 1/16WR265 RK73GH1J562D CHIP R 5.6K D 1/16WR266 RK73GB1J562J CHIP R 5.6K J 1/16WR267 R92-0670-05 CHIP R 0 OHM
R268 RK73GB1J102J CHIP R 1.0K J 1/16WR269 RK73GB1J823J CHIP R 82K J 1/16WR270 RK73GB1J272J CHIP R 2.7K J 1/16WR271 RK73GB1J561J CHIP R 560 J 1/16WR272 RK73GB1J152J CHIP R 1.5K J 1/16W
R273 RK73GB1J472J CHIP R 4.7K J 1/16WR274,275 RK73GB1J153J CHIP R 15K J 1/16WR276 RK73GB1J473J CHIP R 47K J 1/16WR277 RK73GB1J683J CHIP R 68K J 1/16WR278 RK73GB1J123J CHIP R 12K J 1/16W
R279 RK73GB1J472J CHIP R 4.7K J 1/16WR280 RK73GB1J391J CHIP R 390 J 1/16WR281 R92-0670-05 CHIP R 0 OHMR301,302 RK73GB1J472J CHIP R 4.7K J 1/16WR303 RK73GB1J223J CHIP R 22K J 1/16W
R304 RK73GB1J472J CHIP R 4.7K J 1/16WR305 RK73GB1J182J CHIP R 1.8K J 1/16WR306 RK73GB1J274J CHIP R 270K J 1/16WR308 RK73GB1J334J CHIP R 330K J 1/16WR309 RK73GB1J332J CHIP R 3.3K J 1/16W
R310 RK73GB1J102J CHIP R 1.0K J 1/16WR311 RK73GB1J333J CHIP R 33K J 1/16WR312 RK73GB1J473J CHIP R 47K J 1/16WR313 RK73GB1J104J CHIP R 100K J 1/16WR314 RK73GB1J222J CHIP R 2.2K J 1/16W
R315 RK73GB1J183J CHIP R 18K J 1/16WR316 RK73GB1J223J CHIP R 22K J 1/16WR317-320 RK73GB1J103J CHIP R 10K J 1/16WR321 RK73GB1J223J CHIP R 22K J 1/16WR322 RK73GB1J101J CHIP R 100 J 1/16W
R323 RK73GB1J224J CHIP R 220K J 1/16WR324 R92-1252-05 CHIP R 0 OHM J 1/16WR325 RK73GB1J333J CHIP R 33K J 1/16WR349 RK73GB1J473J CHIP R 47K J 1/16WR350 RK73GB1J273J CHIP R 27K J 1/16W
R351 RK73GB1J471J CHIP R 470 J 1/16WR352 RK73GB1J101J CHIP R 100 J 1/16WR353 RK73GB1J104J CHIP R 100K J 1/16WR354 RK73GB1J331J CHIP R 330 J 1/16WR355 RK73GB1J471J CHIP R 470 J 1/16W K,M
R355,356 RK73GB1J102J CHIP R 1.0K J 1/16W K2,M2R356 RK73GB1J102J CHIP R 1.0K J 1/16W K,MR358 RK73GB1J470J CHIP R 47 J 1/16WR359 RK73GB1J224J CHIP R 220K J 1/16WR360 RK73GB1J474J CHIP R 470K J 1/16W
R361 RK73GB1J470J CHIP R 47 J 1/16W K,MR361 RK73GB1J560J CHIP R 56 J 1/16W K2,M2R362 RK73GB1J474J CHIP R 470K J 1/16WR363 RK73GB1J154J CHIP R 150K J 1/16WR364 R92-1252-05 CHIP R 0 OHM J 1/16W
R365 RK73GB1J104J CHIP R 100K J 1/16WR366 RK73GB1J471J CHIP R 470 J 1/16WR367 RK73GB1J470J CHIP R 47 J 1/16WR368 RK73GB1J104J CHIP R 100K J 1/16WR369 R92-1252-05 CHIP R 0 OHM J 1/16W
R370 RK73GB1J151J CHIP R 150 J 1/16WR371 RK73GB1J474J CHIP R 470K J 1/16WR372 RK73GB1J124J CHIP R 120K J 1/16W K2,M2R372 RK73GB1J224J CHIP R 220K J 1/16W K,MR373 RK73GB1J684J CHIP R 680K J 1/16W
R374 RK73GB1J124J CHIP R 120K J 1/16W K2,M2R374 RK73GB1J184J CHIP R 180K J 1/16W K,MR375,376 RK73GB1J104J CHIP R 100K J 1/16WR378 RK73GB1J100J CHIP R 10 J 1/16W K2,M2R378 R92-1252-05 CHIP R 0 OHM J 1/16W K,M
R379 RK73GB1J104J CHIP R 100K J 1/16WR401-403 RK73GB1J102J CHIP R 1.0K J 1/16WR404 RK73GB1J103J CHIP R 10K J 1/16WR405 R92-1252-05 CHIP R 0 OHM J 1/16WR407 RK73GB1J152J CHIP R 1.5K J 1/16W
R408 RK73GB1J100J CHIP R 10 J 1/16WR409 RK73GB1J104J CHIP R 100K J 1/16WR410 RK73GB1J103J CHIP R 10K J 1/16W K2,M2R410 RK73GB1J822J CHIP R 8.2K J 1/16W K,MR411 RK73GB1J562J CHIP R 5.6K J 1/16W
R412,413 RK73GB1J103J CHIP R 10K J 1/16WR414 RK73GB1J471J CHIP R 470 J 1/16WR415 R92-1252-05 CHIP R 0 OHM J 1/16WR416 RK73GB1J471J CHIP R 470 J 1/16WR417 RK73GB1J224J CHIP R 220K J 1/16W
R418,419 RK73GB1J102J CHIP R 1.0K J 1/16WR420 RK73GB1J272J CHIP R 2.7K J 1/16WR421 RK73GB1J152J CHIP R 1.5K J 1/16WR422 RK73GB1J103J CHIP R 10K J 1/16WR423 RK73GB1J331J CHIP R 330 J 1/16W K2,M2
R423,424 RK73GB1J221J CHIP R 220 J 1/16W K,MR424 RK73GB1J221J CHIP R 220 J 1/16W K2,M2R425,426 RK73GB1J473J CHIP R 47K J 1/16WR427 RK73GB1J104J CHIP R 100K J 1/16WR428 RK73GB1J473J CHIP R 47K J 1/16W
R429,430 RK73GB1J101J CHIP R 100 J 1/16WR431 RK73GB1J104J CHIP R 100K J 1/16WR432 RK73GB1J102J CHIP R 1.0K J 1/16WR433 RK73GB1J472J CHIP R 4.7K J 1/16WR434 R92-1252-05 CHIP R 0 OHM J 1/16W
R435 RK73GB1J101J CHIP R 100 J 1/16WR436 RK73GB1J124J CHIP R 120K J 1/16WR437 RK73GB1J102J CHIP R 1.0K J 1/16WR438 RK73GB1J223J CHIP R 22K J 1/16WR439 RK73GB1J473J CHIP R 47K J 1/16W
TK-7102H
26
PARTS LIST
Ref. No. Address Parts No. Description Desti-nation
Newparts Ref. No. Address Parts No. Description Desti-
nationNewparts
TX-RX UNIT (X57-6700-XX)
R440-442 RK73GB1J101J CHIP R 100 J 1/16WR443 RK73GB1J222J CHIP R 2.2K J 1/16WR444 RK73GB1J102J CHIP R 1.0K J 1/16WR501 RK73GB1J102J CHIP R 1.0K J 1/16WR502 RK73GB1J271J CHIP R 270 J 1/16W
R503 RK73GB1J180J CHIP R 18 J 1/16WR504 RK73GB1J271J CHIP R 270 J 1/16WR505 RK73GB1J222J CHIP R 2.2K J 1/16WR506 RK73GB1J103J CHIP R 10K J 1/16WR507 RK73GB1J100J CHIP R 10 J 1/16W
R509 RK73GB1J220J CHIP R 22 J 1/16WR510 RK73GB1J152J CHIP R 1.5K J 1/16WR511 RK73FB2A470J CHIP R 47 J 1/10WR512 RK73FB2A100J CHIP R 10 J 1/10WR513 RK73FB2A222J CHIP R 2.2K J 1/10W
R514 R92-1217-05 CHIP R 0 OHMR516 R92-0670-05 CHIP R 0 OHMR518 RK73EB2B330J CHIP R 33 J 1/8WR519 RK73GB1J333J CHIP R 33K J 1/16WR520 RK73GB1J183J CHIP R 18K J 1/16W
R521 RK73GB1J101J CHIP R 100 J 1/16WR522 RK73EB2B181J CHIP R 180 J 1/8W K,MR522 RK73EB2B331J CHIP R 330 J 1/8W K2,M2R523 RK73GB1J393J CHIP R 39K J 1/16W K,MR523 RK73GB1J473J CHIP R 47K J 1/16W K2,M2
R524 R92-1215-05 CHIP R 470 J 1/2WR525 RK73GB1J563J CHIP R 56K J 1/16WR526 R92-1261-05 CHIP R 150 J 1/2WR527 RK73GB1J224J CHIP R 220K J 1/16WR528,529 RK73GB1J471J CHIP R 470 J 1/16W
R530 RK73GB1J102J CHIP R 1.0K J 1/16WR531 RK73GB1J473J CHIP R 47K J 1/16WR532,533 R92-1252-05 CHIP R 0 OHM J 1/16WR601,602 RK73GB1J223J CHIP R 22K J 1/16WR603 RK73GB1J473J CHIP R 47K J 1/16W
R605 RK73GB1J153J CHIP R 15K J 1/16WR606 RK73GB1J221J CHIP R 220 J 1/16WVR1 R12-6427-05 TRIMMING POT. (47K)
D1-11 DA221 DIODED31 ZSH5MA27 SURGE ABSORBERD32 1812L110PR VARISTORD61 02DZ18(X,Y) ZENER DIODED201 DAN222 DIODE
D202 1SS372 DIODED251 MA742 DIODED301 MA742 DIODED302,303 DAN222 DIODED351-354 HVC350B VARIABLE CAPACITANCE DIODE
D401 MA2S111 DIODED402 HZU5ALL DIODED403-406 MA2S304 VARIABLE CAPACITANCE DIODED407 MA360 VARIABLE CAPACITANCE DIODED408 MA2S111 DIODE
D409 DAN235E DIODED501 1SS355 DIODED502 DA221 DIODED503 02DZ5.1(Y) ZENER DIODED602 MA4PH633 DIODE
D603 XB15A709 DIODE K,M
D604,605 XB15A709 DIODE K2,M2D605 XB15A709 DIODE K,MD606,607 MA742 DIODED608 1SS355 DIODEIC31 KIA7808AF ANALOG IC
IC32,33 NJM78L05UA BI-POLAR ICIC34,35 PST9140NR MOS ICIC66 AT24C64N10SI18 ROM ICIC101 30622MAA-B83GP MPUIC161 M62363FP MOS IC
IC201 NJM2100V MOS ICIC202 NJM2904V MOS ICIC203 NJM2902V MOS ICIC251 NJM2902V MOS ICIC252 2B LA4600 AF POWER IC
IC301 TK14489V BI-POLAR ICIC401 MB15A02 MOS ICIC402 UPB1509GV BI-POLAR ICIC501 TA75W01FU MOS ICQ1 2SK1824 FET
Q31 2SA1641(S,T) TRANSISTORQ32 KRC102S DIGITAL TRANSISTORQ33 2SA1745(6,7) TRANSISTORQ34 KRC102S DIGITAL TRANSISTORQ35 KTA1664(Y) TRANSISTOR
Q36 KRC102S DIGITAL TRANSISTORQ61 KRC404RTK DIGITAL TRANSISTORQ71 KRC414RTK DIGITAL TRANSISTORQ86,87 2SK1824 FETQ201 2SC4919 TRANSISTOR
Q202 2SJ243 FETQ251 2SC4617(S) TRANSISTORQ252,253 2SK1824 FETQ254 DTC363EU DIGITAL TRANSISTORQ255 KRC102S DIGITAL TRANSISTOR
Q301 2SC2412K TRANSISTORQ302 2SC4617(S) TRANSISTORQ351 2SC5108(Y) TRANSISTORQ352,353 3SK255 FETQ354 2SK1824 FET
Q402 2SA1832(GR) TRANSISTORQ403 2SC4738(GR) TRANSISTORQ404 2SC4649(N,P) TRANSISTORQ405,406 2SK508NV(K52) FETQ407 2SJ243 FET
Q408 KRX102U TRANSISTORQ410 2SC5108(Y) TRANSISTORQ411 2SC4649(N,P) TRANSISTORQ440 2SC4617(S) TRANSISTORQ501,502 2SC3357 TRANSISTOR
Q503 PD55003TR FETQ504 2B RD70HVF1-01 RF POWER FETTH97,98 B57331V2104J THERMISTORTH301 B57331V2104J THERMISTORTH351 B57331V2104J THERMISTOR K2,M2
TK-7102H
27
EXPLODED VIEWA B
1
2
3
16
43
4728
5
3
19
1
2
32
33 21
31
2624
15Q504
IC252
A
700Caution label
701S/No. label
AA
C
C
CC
C CCx2
Bx12
B
B
12
30
2725
10
TX-RX unitDisplay unit
A M2.6 x 8 : N67-2608-46B M2.6 x 6 (Br-Tap) : N87-2606-46C M2.6 x 14 (Br-Tap) : N87-2614-46
Parts with the exploded numbers larger than 700 are not supplied.
TK-7102H
28
PACKINGC D
1
2
3
37 Protection bag (H25-2341-04)
37 Protection bag (H25-2341-04)
35 Packing fixture (H12-3112-05)
35 Packing fixture (H12-3112-05)
8 Instruction manual (English) (B62-1596-10)
9 Instruction manual (Spanish) (B62-1597-10)
702 Pamphlet
703 Pamphlet
48 Microphone (T91-0624-05) : K,K2
38 Item carton cse (H52-1829-22)
45 Screw set (N99-0395-05)
41 Bracket (J29-0662-03)
40 Holder (J19-1584-05) : K,K2 36 Carton board
(H13-1190-02)
14 DC cord (E30-3339-05)
22 Fuse (6x30) (F51-0017-05) x 2
Parts with the exploded numbers larger than 700 are not supplied.
TK-7102H
29
Test Equipment Required for Alignment
Test Equipment Major Specifications
1. Standard Signal Generator Frequency Range 136 to 175MHz(SSG) Modulation Frequency modulation and external modulation
Output –127dBm/0.1µV to greater than –7dBm/100mV2. Power Meter Input Impedance 50Ω
Operation Frequency 136 to 175MHz or moreMeasurement Capability Vicinity of 100W
3. Deviation Meter Frequency Range 136 to 175MHz4. Digital Volt Meter Measuring Range 1 to 20V DC
(DVM) Accuracy High input impedance for minimum circuit loading5. Oscilloscope DC through 30MHz6. High Sensitivity Frequency Range 10Hz to 1000MHz
Frequency Counter Frequency Stability 0.2ppm or less7. Ammeter 20A8. AF Volt Meter Frequency Range 50Hz to 10kHz
(AF VTVM) Voltage Range 1mV to 3V9. Audio Generator (AG) Frequency Range 20Hz to 20kHz or more
Output 0 to 1V10. Distortion Meter Capability 3% or less at 1kHz
Input Level 50mV to 10Vrms11. 4Ω Dummy Load Approx. 4Ω, 10W or more12. Regulated Power Supply 13.6V, approx. 20A (adjustable from 9 to 17V)
Useful if ammeter requipped13. Spectrum Analyzer Center frequency 50KHz to 600MHz14. Tracking Generator Output Voltage 100mV or more
Tuning cable (E30-3383-05)
Adapter cable (E30-3383-05) is required forinjecting an audio if PC tuning is used.See “PC Mode” section for the connection.
MIC connector
(Front view)
Test cable for microphone input (E30-3360-08)
1 : BLC2 : PSB3 : E4 : PTT5 : ME6 : MIC7 : HOOK8 : CM
ADJUSTMENT
Lead wire +
MICShield wire –
3
2
4
5
6
7
8
3
1
2
4
5
6
7
8
1GREEN
RED
BLACK
BLUE
SHIELD
WHITE
GRAY
YELLOW
PTT
E
MIC-E
MIC
HK
18
TK-7102H
30
ADJUSTMENT
Adjustment Location
Switch
Adjustment Points
Notes
• EEPROMThe tuning data (Deviation, Squelch, etc.) for the EEP-
ROM, is stored in memory. When parts are changed, re-adjust the transceiver.
• AF PA IC (IC252)How to mounting the IC252.
• Speaker CableThe speaker cable should be formed before mounting the
shield cover as below.
• FuseTo mount the fuse, the cable terminal direction must be as
follow.
Locator
Speakercable
This side up This side up
Cable terminal Cable terminal
Fuse
Pin 1 marker
IC25
2
Part name label face down
TX-RX UNITComponent side
Power
MIC jack 1/2/3/4 keys
Volumeup/down
key
key Speaker
Display
CV
R518
F501
Q503Q504
IC25
2
R516
R524
CNVSS
RESETPOWER
5M
E +B
RF
RXD TXD
DC
PC8T
IGN BPF
TEMP1
AFV
8T
TEMP2
TX-RX unitComponent side
VR1
ANT
TC401
TC402L301
TC351
TC352
E+B
BPF
TX-RX unitFoil side
TK-7102H
31
ADJUSTMENT
PCB Section
1. Setting 1) Power supply voltageDC Power supply terminal : 13.6V
2. VCO lock 1) CH : TX high Digital voltmeter CV TC402 5.5V ±0.1Vvoltage*
2) CH : RX high TC401 5.5V ±0.1V
3) CH : TX low Check 0.7V or more
4) CH : RX low
3. IF coil 1) CH : RX center (Wide) SSG AFV L301 3.25~3.35V (DC)2) SSG output : –53dBm (501µV) Digital voltmeter
Mod : 1kHzDev : 3kHz
4. RF 1) CH : RX center (Wide) Tra generator ANT TC351 Adjust the BPF waveformbandpass CH : RX low (Wide) Spectrum analyzer BPF TC352 to Fig. 1filter CH : RX high (Wide)
2) Tra generator output : –30dBmConnect the spectrum analyzerto BPF terminal
* Adjustment of TX VCO lock voltage1. Remove R516, F501, R518 and R524 (all on component side).2. Remove PCB from chassis.3. Transmit and check voltage at [CV] point.Warning : Do not transmit if step “1.” is not complete.4. Adjust of voltage can be done by tuning TC402.
Item ConditionTest equipment Terminal Parts Method
Specifications/
Remarks
Measurement Adjustment
Fig. 1
Test Frequency (MHz)
ChannelK,M K2,M2
TX RX TX RX
1 : Center 160.100 160.050 149.100 149.0502 : Low 146.100 146.050 136.100 136.0503 : High 173.900 173.950 161.900 161.9504 160.000 160.000 149.000 149.0005 160.200 160.200 149.200 149.2006 160.400 160.400 149.400 149.400
K2,M2K,M
TK-7102H
32
ADJUSTMENT
Receiver Section
1. Seisitivity 1) CH : RX low (Wide/Narrow) SSG ANT Check SINADCH : RX center (Wide/Narrow) Oscilloscope EXT. SP : 12dB or higherCH : RX high (Wide/Narrow) AF V.M
2) SSG output Distortion meter: –118dBm (0.28µV) (Wide): –116dBm (0.35µV) (Narrow)Mod : 1kHzDev : ±3.0kHz (Wide)Dev : ±1.5kHz (Narrow)
2. Squelch 9 1) CH : RX low (Wide) PC key Adjust to open the squelchCH : RX center (Wide/Narrow)CH : RX high (Wide)
2) SSG output: –115dBm (0.4µV) (Wide): –114dBm (0.45µV) (Narrow)Mod : 1kHzDev : ±3.0kHz (Wide)Dev : ±1.5kHz (Narrow)
3. Squelch 1 1) CH : RX low (Wide)CH : RX center (Wide/Narrow)CH : RX high (Wide)
2) SSG output: –120dBm (0.22µV) (Wide): –119dBm (0.25µV) (Narrow)Mod : 1kHzDev : ±3.0kHz (Wide)Dev : ±1.5kHz (Narrow)
Item ConditionTest equipment Terminal Parts Method
Specifications/
Remarks
Measurement Adjustment
Transmitter Section
1. Frequency 1) CH : TX center Frequency counter ANT PC key Adjust to center frequency Within ±100Hz2) Transmit
2. Maximum 1) CH : TX high Power meter VR1 53W ±1Wpower 2) Transmit Hex data 255limitting
3. High 1) CH : TX low PC key 50W ±1.0Wpower CH : TX low’
CH : TX centerCH : TX high’CH : TX high
2) Transmit
4. Low 1) CH : TX low 25W ±1.0Wpower CH : TX low’
CH : TX centerCH : TX high’CH : TX high
2) Transmit
Item ConditionTest equipment Terminal Parts Method
Specifications/
Remarks
Measurement Adjustment
TK-7102H
33
If normal power is not obtained, please follow the
step belowOpen the shielding cover (upper), and screw 3 locationsaround ANT pin.1. Switch off the transceiver.
Impedance of Final FET (Q504) and Drive FET (Q503) canbe measured easily using DVM Ω mode.Normal condition – Gate : 20kΩ~50kΩ, Drain : 1MΩ~2MΩThe above impedance values are rough estimations.
2. Switch on the transceiver. Check the voltage at F501 out-put point.The voltage is around 13.6V in receiving condition. Thevoltage will be 12.6V~ in transmitting condition. If found0V at this point then F501 is broken.
3. Remove R516.
4. Connect 50Ω load at the ANT location.Transmit and check current drain at High power mode.If the current drain is less than 1A, then Final FET is bro-ken.If the current drain is less than 5.0A, short the Drive FETgate to ground, and check the current drain.If the current drain is not 0.1A less than the original value,then the Drive FET is broken.
5. Check input power level at Drive FET gate location.Connect the wire to [RF] location.Transmit and check for power to be within the range of0.3W~0.6W.If power found is less than 0.3W, check the circuit beforethe Drive FET.
ADJUSTMENT
5. DQT 1) CH : TX low (Wide) Modulation analyzer ANT PC key Adjust the waveform as belowbalance CH : TC center (Wide/Narrow) or Linear detector
CH : TX high (Wide) (LPF : 3kHz)2) Transmit Oscilloscope
6. MAX 1) CH : TX low (Wide) Modulation analyzer ANT ±4.0kHz (Wide) ±50Hzbalance CH : TC center (Wide/Narrow) or Linear detector MIC ±2.0kHz (Narrow)
CH : TX high (Wide) (LPF : 15kHz) According to the large +, –2) AG : 1kHz/50mV Oscilloscope3) Transmit AG
AF V.M7. MIC 1) CH : TX center (Wide/Narrow) Check ±3kHz±0.2kHz
sensitivity 2) AG : 1kHz/5mV (Wide)3) Transmit ±1.5kHz±0.1kHz
(Narrow)
8. DQT 1) CH : TX low (Wide) Modulation analyzer ±0.75kHz (Wide) ±0.05kHzdeviation CH : TX center (Wide/Narrow) or Linear detector ±0.35kHz (Narrow)
CH : TX high (Wide) (LPF : 3kHz)2) Transmit Oscilloscope
9. QT 1) CH : TX low (Wide) ±0.75kHz (Wide) ±0.05kHzdeviation CH : TX center (Wide/Narrow) ±0.35kHz (Narrow)
CH : TX high (Wide)2) Transmit
10. DTMF 1) CH : TX center (Wide/Narrow) ±3.0kHz (Wide) ±0.2kHz/MSK 2) Transmit ±1.5kHz (Narrow)deviation
Item ConditionTest equipment Terminal Parts Method
Specifications/
Remarks
Measurement Adjustment
TK-7102H
34
TERMINAL FUNCTION
CN2
No. Name I/O Function
1 SB O Battery voltage DC supply
2 NC - -
3 GND O Ground
4 NC - -
5 FNC1 I/O Programable I/O (programmed by FPU)
6 FNC2 I/O Programable I/O (programmed by FPU)
7 FNC3 I/O Programable I/O (programmed by FPU)
8 FNC4 I/O Programable I/O (programmed by FPU)
9 FNC5 I/O Programable I/O (programmed by FPU)
10 FNC6 I/O Programable I/O (programmed by FPU)
11 FNC7 I/O Programable I/O (programmed by FPU)
12 FNC8 I/O Programable I/O (programmed by FPU)
Function Port Assignment
KDS100, KGP-2A/2B
Name I/O
FNC1 - -
FNC2 - -
FNC3 Data Channel I
FNC4 PTT I
FNC5 Carrier Operated Relay O
FNC6 Audio Mute I
FNC7 Mic Mute I
FNC8 TX Relay O
SmarTrunk II
Name I/O
FNC1 TXD O
FNC2 RXD I
FNC3 Reset O
FNC4 - -
FNC5 - -
FNC6 - -
FNC7 - -
FNC8 - -
Scrambler
Name I/O
FNC1 - -
FNC2 - -
FNC3 TX Relay O
FNC4 Scrambler O
FNC5 Scrambler Code1 (1) O
FNC6 Scrambler Code2 (2) O
FNC7 Scrambler Code3 (4) O
FNC8 Scrambler Code4 (8) O
Port Function is Low Active. (Exclude : Scrambler Code)
CN3
No. Name I/O Function
1 IGN I Ignition sens input
2 DATAI I External transmit signal input
3 DETO O FM detector output
4 TXAFI I TX audio input from scrambler board
5 TXAFO O TX audio output to scrambler board
6 EMGMIC I Emergency MIC input (1kHz/1.2mVrms)
7 RXAFO O RX audio output to scrambler board
8 ALTI I External alert tone signal input
9 RXAFI I RX audio input from scrambler board
10 5C O 5V DC power supply (50mA MAX)
11 8C O 8V DC power supply (50mA MAX)
CN4
No. Name I/O Function
1 GND O Ground
2 NC - -
3 NC - -
4 NC - -
5 FNC2 I/O Programable I/O (programmed by FPU)
6 NC - -
7 NC - -
8 FNC3 I/O Programable I/O (programmed by FPU)
9 FNC1 I/O Programable I/O (programmed by FPU)
10 NC - -
11 5C O 5V DC power supply (50mA MAX)
12 NC - -
13 DATAI I External transmit signal input
14 DETO2 O FM detector output
15 ALTI I External alert tone signal input
16 NC - -
17 NC - -
18 NC - -
19 NC - -
20 GND O Ground
SRQPONMLKJIHGFEDCBA
1
2
3
4
5
6
7
8
9
10
11
12
13
14
GNDPTTMIC
POWERME
HOOKKMI2
CMKMI1KMI3
KMO1KMI4
KMO2SB5C
CLDI
CN
1
HOOK
CM PTTMIC SB
MBLGNDME
18
1
C25
C27
Q10
C4
C8
C9
D13
L1
IC1
189 16
R10
R11R12
R13
R14
R15
R16
R17 R18
R19
R20Q
4
Q9
R1
R2
R3
R4
R5R6
R7
R8
R9
CP3
CP4
C10C11
C12
C13
C14
C15
C16
C17
C18
DICL
5CSB
KMO2KMI4
KMO1KMI3KMI1
CMKMI2
HOOKME
POWERMICPTT
GND
CN
1
HOOK
CM PTTMIC SB
MBLGNDME
18
1
C25
C27
Q10
C4
C8
C9
D13
L1
IC1
189 16
R10
R11R12
R13
R14
R15
R16
R17
R18
R19
R20
Q4
Q9
R1
R2
R3
R4
R5R6
R7
R8
R9
CP3
CP4
C10
C11
C12
C13
C14
C15
C16
C17
C18
J72-0916-09
J1
D1D2
D3D4
D5
D6
D7 D8
D9
D10
D11
D12
POWER
UP
DOWN
1 2 3 4
MONI
PROG
J72-0916-09
J1
D1D2
D3
D4
D5
D6
D7 D8
D9
D10
D11
D12
POWER
UP
DOWN
1 2 3 4
MONI
PROG
PC BOARD TK-7102H
3635
DISPLAY UNIT (X54-3460-20) Component side view (J72-0916-09)
DISPLAY UNIT (X54-3460-20) Foil side view (J72-0916-09)
Component side
Foil side
Ref. No. Address
IC1 4I
Q4 4G
Q9 4A
Q10 5A
D1 7K
D2 7F
D3 3M
D4 3D
D5 2J
D6 3J
D7 5E
D8 5G
D9 5J
D10 5L
D11 3G
D12 2G
D13 4K
Ref. No. Address
IC1 11I
Q4 11G
Q9 11A
Q10 10A
D1 8K
D2 8F
D3 12M
D4 12D
D5 13J
D6 12J
D7 10E
D8 10G
D9 10J
D10 10L
D11 12G
D12 13G
D13 11K
A B C D E F G H I J K L M N O P Q R S
1
2
3
4
5
6
7
8
9
10
11
12
13
14
C21C22
C23
R210
R405
R407
R408
C29
R409
R218R219
R605
IC16
1
1 121324
R412
R221
R222
R223
R224
R418R226
R227 R228
R421
R422 CVC44
C45
R232
R233
C49
C50
C51
C201
C202
C52
C204
C205
C207
C208
C401
C402
C403
C404
C406
C212
R250
C409C217
C218
C411
C605
C220
C414
C608
C221
C72
C416
C225
C77C78
C613
R267
R268
C615
C422
C424
C231
C425
C232
C83
C233
R270
R271
R272
R273
R274R275
Q36
R277
C97
C442
D2
D3
D8
D9
D202
Q302
C269
D402
C270
C271
C272
C274
Q71
C276
D603
D608
IC20
3
178 14
L508
L509
D251Q354
R101
R105R106
D11
R302
R304
R114 R115
R118
R119
R311R313
R314
R315
R316
R318
R322
R323
R518
R519
R520
R521
C103
R528
R530
R531
C303C304
C305
R151
R152
C310
C311
C312
R350
R351 C315C316
C317
R354
C318
R161R162
R163
R164
R165
R166
C517
C323
C518
C519
Q1
C522
C527
C528
C529
R1
R35
R2
R37
C530
R379
R5
C533
C536
C152
C545
C351
C546
C162C163
C164
Q201
C550
C554 C555
D303
Q40
2
Q403
L201
R72
R74
R76
L403
R78
L404
C574
C576
R81
R82
C389
IC501
CN
1
CN3
111
CN
4
1G
ND
NC
TXD
ATA
NC
RXDA
TAV
CC
SIG
OU
T(H
)BE
EPOU
T(H)
IRO
NC
NC
NC
NC
RES
ETSI
GO
UT(
L) NC
DIS
CBE
EPOU
T(L)
NC
GN
D
2
1920
CN
5
TH97
Q253
Q254
C10
C13
C14
R201
R202C16
R203
R204
R205
R206
R208C
20
R40
1
R40
2
R40
3
R40
4
R21
1R
212
R21
3
C28
R21
4R
215
R21
6
R21
7
R60
3
VR
1
R41
0R
411
R60
6
R41
3
R22
0
R41
4
R41
9
R22
5
IC33
O G B
1DI CE SB
KMI4
KMI3 CM
HOOK
POW
ER PTT
CL 5C KMO2
KMO1
KMI1
KMI2
GND
MIC
GND
17
2 18
CEI
R22
9
R42
0
R23
0
R23
1
C20
3C
206
R24
9
C21
0
C21
1
C21
3
C40
8
C21
4
C21
5
C60
2
C60
3
C41
0
X401
C41
2
C41
3
C41
7
C22
6
C22
7
C22
8
C22
9
R26
9
C42
3
C23
0
C82
Q35
F501
R27
6
R27
8R
279
R28
0
C98
C25
0
D1
D4
D5
D6
D7
D20
1
C26
7
C26
8
D40
1
Q503
C27
3
Q504G D
C27
5
C27
7C
278
IC25
2
110
D60
2
L302
L303
L304
IC201
C28
1
IC202
L503
L504
L505 L5
06
L507
IC401
Q35
1
R10
7
D10
R10
8
R30
3
R30
5
R30
6
R11
2
R11
3
R11
6
R11
7
R31
2
R12
0R
121
R12
2
R31
7R12
4
R31
9
R32
0
R32
1
R51
6
R32
4
R52
3
R52
4
R52
5
R52
7
R52
9
R53
2
R53
3
TH30
1
R34
9
C31
3 C31
4
R35
2
R35
3
R35
5
TH35
1
C31
9
C51
4C
516
C32
2C
324
C52
5
R36
R3
C53
1
C15
1
C54
1C
542
C35
0
C35
3
C54
9
C35
5
C16
1
Q20
2
C55
2C
553
D30
2
C55
9C
560
D50
3
R71
R73
R75
L401
R77
CN
2
TH98
Q25
2
Q25
5
C15
8C 5C RX
AFI
ALT
IR
XA
FOEM
GM
ICTX
AFO
TXA
FID
ETO
DAT
AI
IGN
C17
C18
C19
R20
7
R20
9
J1
+
+
+
CNVSS
RESETPOWER
5M
1 SBNC
GNDNC
FNC1FNC2FNC3FNC4FNC5FNC6FNC7FNC812
E SP
E +B
RF
+
RXD
TXD
SD
G
SD G
SD
G
SD
G
SD
G
+
+
+
S
S
DG
+
DC
PC
8T1
45
8
IGN
+
+
+
+
+
+
+
+
+
1
1011
20
BPF
TEMP1
AFV
+ +
+ +
+
+
8T
TEMP2
1
4 5
8
1
4 5
8
J72-0886-19
TK-7102H PC BOARD
37 38
TX-RX UNIT (X57-6700-XX) -22 : M -23 : M2 -24 : K -25 : K2 Component side view (J72-0886-19)
Component side
Foil side
Layer 1Layer 2Layer 3Layer 4
Ref. No. Address
IC33 12B
IC161 10N
IC201 10Q
IC202 11Q
IC203 12Q
IC252 10B
IC401 12J
IC501 8K
Q1 10F
Q35 13C
Q36 12C
Q71 11F
Q201 11P
Q202 11I
Q252 12G
Q253 12F
Q254 11D
Q255 10D
Q302 13L
Q351 12N
Q354 9P
Q402 12I
Q403 13I
Q503 6H
Q504 5L
D1 12D
D2 13F
D3 12F
D4 11E
D5 11F
D6 11E
D7 11E
D8 12E
D9 12E
D10 12E
D11 12F
D201 11O
D202 10O
D251 9E
D302 12O
D303 12P
D401 12J
D402 13I
D503 8J
D602 7P
D603 7Q
D608 7L
SRQPONMLKJIHGFEDCBA
1
2
3
4
5
6
7
8
9
10
11
12
13
14
C24
CF3
01
C25C26
CF302
R601R
602
C30
C33
C34
C35
R41
5
R41
6
C36
R417
C37
C38
IC31
I
O
G
C39
IC32
IC34
1 345
1 345
IC35
C40
C41
C42 C43
R42
3
R42
4R
425
R42
6
R427
R428
CN601ANT
R42
9
R43
0
R43
1
R43
2
C53
R43
3
C54R434
R435
C55
R43
6 C56R437
R438R439
R440
C61
R44
1
R442
R443
R444
R25
1R252C66R253
R25
4
R255
C601
R256
R25
7
R258
R25
9
IC66
C606C607
R260
C418
R261
TC40
1
TC40
2
R262
R263
C610R
264
C61
1
R26
5R26
6
C42
1
C616C
617
C426
C42
7
C42
8
Q31
E B
C
C42
9
Q32
Q33
C87
C88
Q34
C89
C430
C431
C43
2
C90
C43
4C
435
C436
C437
C438
R28
1
C43
9C440
C441C
444
C251
C252C25
3
C254
C44
8
C44
9
C255C256
C257
C258 C25
9 C450
C451 C452
C45
3
C454
C260
C45
5
C261
C45
6
C26
2
C457
C26
3
C458
C264
Q301
C459
Q61
C26
5
C26
6
C46
0
L101
C461C462
C46
3
D40
3
D404
C464
D40
5
Q50
1
B C E
C465
D406
Q502
B
C
E
C466
D407
C46
7
C46
8
D40
8
D40
9 C279
L301
D60
5
C471
D606
D607
C28
0
C28
2
C28
3
L501
L502
Q86
Q87
IC4021
45
8
Q35
21 234
Q353123
4
R102R103
R10
4
R10
9
R30
1
R110
L351
R11
1
L352L3
54
R30
8
R309
L355
L356
L357
IC251
1
78
14
R50
1
R50
2
R503
R310
R50
4 R505
R50
6
R50
7
R509
R123
R125R126
R127
R51
0
R128
R51
1
R129
D31
R512
D32
R513 R51
4
R130
R325
R131
R522
C101
R526
C102
C104
C30
1
C302
C306
C307
C308
C309
C501
C50
2
C503
C504
D61
C50
5
C50
6
C50
7
C509
R35
6
R358
C510
C51
1
R359
C51
2 C51
3
C515
R360
XF351
R36
1
R362
C326
R36
3
R36
4R
365
R36
6
R367
R36
8
R36
9
C526
R370
R371
R31
R372
R32
R33
R373
R34
R374
R37
5
R37
6
R4
R37
8
R38
R39
R40 R41
C35
7
C35
8
C359 C36
0
D30
1
C36
1
C556
C36
2
C55
7
C36
3
C558
C364
R61
R62
C366
C367
Q404
C368
Q40
5
GS D
GSD
C36
9
TC35
1
Q406
GS
D
R66
TC352
Q40
7
R67
Q408123
5
R68
D501
R69
D502
C370
C37
1
C37
2
C373C37
4
Q410
R70
C37
5
IC101
Q411
C37
6C377
C378
C37
9
L405
L406
L407
C38
0
L408
L409
IC301
C38
2
C38
3
C38
4
L601
L602
C386
L603
C38
7
L604
L410
C38
8
L605
L411
R86
L412
R87
L413
L414
L415
L416
L417
L418
L419
R91
R92R93
L420
R94
L421
L422
Q44
0
Q25
1
X86
D35
1
D352
D35
3
D354
+
+
I
G
O
+
+
+
GSDGSD
+
E+B
12526 100
5051 75
76
1
4 5
8
+
BPF
+
1
1011
20
J72-0886-19
D604
TX-RX UNIT (X57-6700-XX) -22 : M -23 : M2 -24 : K -25 : K2 Foil side view (J72-0886-19)
Component side
Foil side
Layer 1Layer 2Layer 3Layer 4
PC BOARD TK-7102H
39 40
Ref. No. Address
IC31 12R
IC32 13Q
IC34 13N
IC35 12M
IC66 11M
IC101 11O
IC251 12C
IC301 12G
IC402 13H
Q31 5R
Q32 4R
Q33 12Q
Q34 12Q
Q61 4R
Q86 10O
Q87 10P
Q251 11C
Q301 13G
Q352 10H
Q353 10C
Q404 12J
Q405 11K
Q406 13L
Q407 11J
Q408 11J
Q410 12K
Q411 12H
Q440 12J
Q501 10K
Q502 10L
D31 3O
D32 5R
D61 4Q
D301 13H
D351 10E
D352 10D
D353 9C
D354 7C
D403 11L
D404 11L
D405 12L
D406 12L
D407 12L
D408 12J
D409 10H
D501 10J
D502 10L
D604 7C
D605 7C
D606 5C
D607 4C
A B C D E F G H I J K L M N O P Q R S
1
2
3
4
5
6
7
8
9
10
11
12
13
14
C24
CF3
01
C25C26
CF302
R601
R60
2
C30
C33
C34
C35
R41
5
R41
6
C36
R417
C37
C38
IC31
I
O
G
C39
IC32
IC34
134 5
134 5
IC35
C40
C41
C42C43
R42
3
R42
4R
425
R42
6
R427
R428
CN601ANT
R42
9
R43
0
R43
1
R43
2
C53
R43
3
C54 R434
R435
C55 R43
6
C56
R437
R438 R439
R440
C61
R44
1R442
R443
R444
R25
1 R252C66 R253
R25
4
R255
C601
R256
R25
7
R258
R25
9
IC66
C606 C607
R260
C418
R261
TC40
1
TC40
2
R262
R263
C610
R26
4
C61
1
R26
5 R26
6
C42
1
C616
C61
7
C426
C42
7
C42
8
Q31
EB
C
C42
9
Q32
Q33
C87
C88
Q34
C89
C430
C431
C43
2
C90
C43
4C
435
C436
C437
C438
R28
1
C43
9
C440
C441
C44
4
C251
C252 C25
3
C254
C44
8
C44
9
C255C256
C257
C258C25
9C450
C451
C452
C45
3
C454
C260
C45
5
C261
C45
6
C26
2
C457
C26
3
C458
C264
Q301
C459
Q61
C26
5
C26
6
C46
0
L101
C461 C462
C46
3
D40
3
D404
C464
D40
5
Q50
1
BCE
C465
D406
Q502
B
C
E
C466
D407C
467
C46
8
D40
8
D40
9C279
L301
D60
5
C471
D606
D607
C28
0
C28
2
C28
3
L501
L502
Q86
Q87
IC4021
4 5
8
Q35
2 123 4
Q35312 3
4
R102 R103 R10
4
R10
9
R30
1
R110
L351
R11
1
L352
L354
R30
8
R309
L355
L356
L357
IC251
1
7 8
14
R50
1
R50
2
R503
R310
R50
4R505
R50
6
R50
7
R509
R123
R125R126
R127
R51
0
R128
R51
1
R129
D31
R512
D32
R513R51
4
R130
R325
R131
R522
C101
R526
C102
C104
C30
1
C302
C306
C307
C308
C309
C501
C50
2
C503
C504
D61
C50
5
C50
6
C50
7
C509
R35
6
R358
C510
C51
1
R359
C51
2
C51
3
C515
R360
XF351
R36
1
R362
C326
R36
3
R36
4R
365
R36
6
R367
R36
8
R36
9
C526
R370
R371
R31
R372
R32
R33
R373
R34
R374
R37
5
R37
6
R4
R37
8
R38
R39
R40R
41
C35
7C
358
C359C36
0
D30
1
C36
1
C556
C36
2
C55
7
C36
3
C558
C364
R61
R62
C366
C367
Q404
C368
Q40
5
GSD
G SD
C36
9
TC35
1
Q406
GS
D
R66
TC352
Q40
7
R67
Q40812 3
5
R68
D501
R69
D502
C370
C37
1
C37
2
C373 C37
4
Q410
R70
C37
5
IC101
Q411
C37
6
C377
C378
C37
9
L405
L406
L407
C38
0
L408
L409
IC301
C38
2
C38
3
C38
4
L601
L602
C386
L603
C38
7
L604
L410
C38
8
L605
L411
R86
L412
R87
L413
L414
L415
L416
L417
L418
L419
R91
R92 R93
L420
R94
L421
L422
Q44
0
Q25
1
X86
D35
1
D352
D35
3
D354
+
+
I
G
O
+
+
+
G SD G SD
+
1 2526100
505175
76
1
45
8
+
+
1
10 11
20
D604
C21C22
C23
R210
R405
R407
R408
C29
R409
R218
R219
R605
IC16
1
1 121324
R412
R221
R222
R223
R224
R418R226
R227 R228
R421
R422CV
C44
C45
R232
R233
C49
C50
C51
C201
C202
C52
C204
C205
C207
C208
C401
C402
C403
C404
C406
C212
R250
C409C217
C218
C411
C605
C220
C414
C608
C221
C72
C416
C225
C77C78
C613
R267
R268
C615
C422
C424
C231
C425
C232
C83
C233
R270
R271
R272
R273
R274R275
Q36
R277
C97
C442
D2
D3
D8
D9
D202
Q302
C269
D402
C270
C271
C272
C274
Q71
C276
D603
IC20
3
178 14
L508
L509
D251Q354
R101
R105R106
D11
R302
R304
R114 R115
R118
R119
R311R313
R314
R315
R316
R318
R322
R323
R518
R519
R520
R521
C103
R528
R530
R531
C303C304
C305
R151
R152
C310
C311
C312
R350
R351 C315C316
C317
R354
C318
R161R162
R163
R164
R165
R166
C517
C323
C518
C519
Q1
C522
C527
C528
C529
R1
R35
R2
R37
C530
R379
R5
C533
C536
C152
C545
C351
C546
C162C163
C164
Q201
C550
C554 C555
D303
Q40
2
Q403
L201
R72
R74
R76
L403
R78
L404
C574
C576
R81
R82
C389
IC501
CN
1
CN3
111
CN
4
1G
ND
NC
TXD
ATA
NC
RXDA
TAV
CC
SIG
OU
T(H
)BE
EPOU
T(H)
IRO
NC
NC
NC
NC
RES
ETSI
GO
UT(
L) NC
DIS
CBE
EPOU
T(L)
NC
GN
D
2
1920
CN
5
TH97
Q253
Q254
C10
C13
C14
R201
R202C16
R203
R204
R205
R206
R208C
20
R40
1
R40
2
R40
3
R40
4
R21
1R
212
R21
3
C28
R21
4R
215
R21
6
R21
7
R60
3
R41
0R
411
R60
6
R41
3
R22
0
R41
4
R41
9
R22
5
IC33
O G B
1DI CE SB
KMI4
KMI3 CM
HOOK
POW
ER PTT
CL 5C KMO2
KMO1
KMI1
KMI2
GND
MIC
GND
17
2 18
CEI
R22
9
R42
0
R23
0
R23
1
C20
3C
206
R24
9
C21
0
C21
1
C21
3
C40
8
C21
4
C21
5
C60
2
C60
3
C41
0
X401
C41
2
C41
3C41
7
C22
6
C22
7 C22
8
C22
9
R26
9
C42
3
C23
0
C82
Q35
F501
R27
6
R27
8R
279
R28
0
C98
C25
0
D1
D4
D5
D6
D7
D20
1
C26
7
C26
8
D40
1
Q503
C27
3
Q504G D
C27
5
C27
7C
278
IC25
2
110
D60
2
L302
L303
L304
IC201
C28
1
IC202
L503
L504
L505 L5
06
L507
IC401
Q35
1
R10
7
D10
R10
8
R30
3
R30
5
R30
6
R11
2
R11
3
R11
6
R11
7
R31
2
R12
0R
121
R12
2
R31
7R12
4
R31
9
R32
0
R32
1
R51
6
R32
4
R52
3
R52
4
R52
5
R52
7
R52
9
R53
2
R53
3
TH30
1
R34
9
C31
3 C31
4
R35
2
R35
3
R35
5
TH35
1
C31
9
C51
4C
516
C32
2C
324
C52
5
R36
R3
C53
1
C15
1
C54
1C
542
C35
0
C35
3
C54
9
C35
5
C16
1
Q20
2
C55
2C
553
D30
2
C55
9C
560
D50
3
R71
R73
R75
L401
R77
CN
2
TH98
Q25
2
Q25
5
C15
8C 5C RX
AFI
ALT
IR
XA
FOEM
GM
ICTX
AFO
TXA
FID
ETO
DAT
AI
IGN
C17
C18
C19
R20
7
R20
9
J1
+
+
+
CNVSS
RESETPOWER
5M
1 SBNC
GNDNC
FNC1FNC2FNC3FNC4FNC5FNC6FNC7FNC812
E SP
E +B
RF
+
RXD
TXD
SD
G
SD G
SD
G
SD
G
SD
G
+
+
+
S
S
DG
+
DC
PC
8T1
45
8
IGN
+
+
+
++
+
+
+
+
1
1011
20
BPF
TEMP1
AFV
+ +
+ +
+
+
8T
TEMP2
1
4 5
8
1
4 5
8
J72-0886-19
VR
1
D608
TK-7102H PC BOARD
41 42
TX-RX UNIT (X57-6700-XX) -22 : M -23 : M2 -24 : K -25 : K2 Component side view + Foil side (J72-0886-19)
Component side
Foil side
Layer 1Layer 2Layer 3Layer 4
Connect 1 and 4
Ref. No. Address
IC31 12B
IC32 13C
IC33 12B
IC34 13F
IC35 12G
IC66 11G
IC101 11E
IC161 10N
IC201 10Q
IC202 11Q
IC203 12Q
IC251 12Q
IC252 10B
IC301 12N
IC401 12J
IC402 13L
IC501 8K
Q1 10F
Q31 5B
Q32 4B
Q33 12C
Q34 12C
Q35 13C
Q36 12C
Q61 4B
Q71 11F
Q86 10E
Q87 10D
Q201 11P
Q202 11I
Q251 11Q
Q252 12G
Q253 12F
Q254 11D
Q255 10D
Q301 13M
Q302 13L
Q351 12N
Q352 10L
Q353 10Q
Q354 9P
Q402 12I
Q403 13I
Q404 12J
Q405 11I
Q406 13H
Q407 11J
Q408 11J
Q410 12I
Ref. No. Address
Q411 12L
Q440 12J
Q501 10I
Q502 10H
Q503 6H
Q504 5L
D1 12D
D2 13F
D3 12F
D4 11E
D5 11F
D6 11E
D7 11E
D8 12E
D9 12E
D10 12E
D11 12F
D31 3E
D32 5B
D61 4C
D201 11O
D202 10O
D251 9E
D301 13L
D302 12O
D303 12P
D351 10O
D352 10P
D353 9Q
D354 7Q
D401 12J
D402 13I
D403 11H
D404 11H
D405 12H
D406 12H
D407 12H
D408 12J
D409 10L
D501 10J
D502 10H
D503 8J
D602 7P
D603 7Q
D604 7Q
D605 7Q
D606 5Q
D607 4Q
D608 7L
46
7
6
5
4
3
2
1
TSRQPONMLKJIHGFEDCBA
SCHEMATIC DIAGRAM TK-7102HNote : The components marked with a dot (•) are parts of layer 1.
T:7.9V
R:2.78V
R:4.9V
R:7.59V
R:7.25VR:0.75V
R:6.2V
R:7.08V
T:4.9V
T:2.4V
R:0.7mV
R:2.46V
W:4.9VN:0V
R:13.5V
R:0.64V
T:7.5V
R:4.82V
R:6.9V
T:6.9V
R:6.8V
R:4.17V
R:5.44V
R:6.2V
R:4.85V
T:7.9V
T:0.79V
T:16V
T:2.2V
T:2.0V
T:13.6VR:12.6V
R:3.8V
R:0.069V
T:4.8VR:4.8V
R:7.77V
R:6.6V
T:3.37V
R:4.5V
R:13.5VT:13.0V
T:1.5V
R:4.9V
R:4.9V
T:0.82V
R:7.9V
R:0.82V
T:1.09V
R:7.9V
R:1.25V
R:0.76V
T:1.2V
R:1.77V
W:0VN:4.9V
R:12.8V
R:2.4V
R:7.39V
R:4.9VT:0.8mV
R:0.58V
R:3.37V
T:0.38V
T:6.6V
R:2.49V
R:1.2mV
R:7.9V
R:0.89VR:1.66V
R:0.57V
R:1.11V
R:7.9V
5.0V
R:1.85V
R:1.62V
T:6.7VT:0.97V
5.0V
T:7.9V
R:7.9V
4.9V
R:7.9V
R:3.1V
0.17V
3.7V
11.40V
11.1V
0.16V
0.17V
3.7V
11.38V
11.34V
0.16V
0.16V
0.15V
0.17V
11.40V
9.57V
0.16V
4.23V
4.96V
13.46V
11.35V
11.4V
-t
-t
-t
-t
FNC5
FNC8
FNC7
FNC2
FNC6
FNC4
FNC1
FNC3
C25
5
8200
p
C35
8
1000
p
100
C258
0.01u
R222 1k
R35
1
470
C37
6
1000
p
C22
1
0.1u
R60
1
22k
C460
18p
R31
6
22k
L354
*
C52
2
1000
p
17
R421
1.5k
C23
2
1000
p
C45
22u1
0
C264
0.033u
R214
68k
R434
0
C38
1000
p
C42
1
470p
R36
3
150k
2SC4919Q201
R51
3
2.2k
R208
1.5k
L50427n
8T
D31
ZS
H5M
A27
83
C61
1000
p
Q36KRC102S
70
85
R37
0
R42
4
220
8C
C45
1
470p C351
33p
C38
3
1000
p
C26
6
0.1u
R23
3
6.8k
C46
110
00p
R264120k
D607MA742
C61
3
33p
71
C44
0*
C52
5
1000
p
R217
220k
TC
401
10p
R62
1k
R42547k
C44
8
470p
R212
82k
R269
82k
C309
0.022u
R323
220k
C430 5p
C51
10u6
.3
C16
2
4.7u
6.3
R227
22k
8R
R35
2
100
R532
0
C61
1
2p
C30
8
1000
p
C15
1
1800
p
R131 1k
R25
7
1M
L601 5T
R522*
R369
0
C206
1000p
C55
7
0.01
u
C51
310
00p
2SC4617(S)Q251
L351
820n
R52
4
470
C25
9
0.01
u
99
R61
470
C46
3
1000
p
R50
1
1k
L502
68n
45
L417
C42
0.01
u
5M
1
2
3
4 5
6
7
8
C38
7
1000
p
C533*
Q408KRX102U
5C
C60
7
2p
C268
0.1u
R313
100k
C55
8
0.01
u
C43
6
0.5p
C454
6p
R51
2
10
R44
2
100
C36
3
0.01
u
R23
0
120k
R21
6
270k
B
C51
4
1000
p
R20
3
100k
D40
3
MA
2S30
4
D409 DAN235E
C22
5
1u16
C51
1
1000
p
C50
610
00p
71
R364
0
R51
1
47
L201
R166 1k
R31
9
10k
43
IC201NJM2100V
1 2 3 45678
V+
2SK1824Q252
C44
22u1
0
C35
5
15p
C44
4
470p
R38
330k
D50
11S
S35
5
C53
1000
p
C53
1
47u2
5
36
2SJ243Q407
L50327n
C50
1
1000
p
C46
2
10p
L352
560n
L605
9.5T
D406MA2S304
R258
2.7k
R52
6
150
2SC3357Q501
R41
1
5.6k
C15
2
3900
p
C36
1
1000
p
C213
3300p
C77
1000
p
47
C55
6
1000
p
70
C41
3
0.01
u
R503
18
Q32KRC102S
C31
0
0.33
u
C43
22u1
0
8C
R41
3
10k
R605
15k
R34
4.7k
R428
47k
D402
HZU5ALL
R10
4
1k
C61
5
22p
C50
4
1000
p
R60
6
220
R1091.5k
9
C36
2
1000
p
C60
2
5p
46
R31
710
k
L418
*
C37
2
1000
p
C26
3
0.03
3u
C51
833
p
R50
5
2.2k
IC31KIA7808AF
2
COM
1IN
3OUT
R26
1
120k
C441
0.5p
C43
15p
R23
1
68k
R81
47k
D201DAN222
C205
0.1u
8T
99
R20
1
680
L603
5T
C380
1000p
C44
2
10u6
.3
C55
5
5p
R112 47k
R35
6
1k
C46
5
22p
L357
43n
R32
0
10k
R31
810
k
C20
4
2.2u
10
C52
9
1000
p
C439 6p
L509
9.5T
C20
8
0.01
u
C56
1000
p
D2021SS372
D40
5
MA
2S30
4
8R
R429
100
R52
1
100
R32
470
IC32NJM78L05UA
2
COM
3IN
1OUT
R26
2
18k
R1524.7k
C51
210
00p
C41
6
1000
p
C20
2
1000
p
2SC4649(N,P)Q404
B
C37
7
1000
p
C21
4
150p
C37
9
1000
p
C50
5
1000
p
C37
4
22p
R36
6
470
R268
1k
C22
0
4.7u
6.3
C256
0.018u
C503
100p
R36
0
470k
C46
7
1000
p
C61
7
1000
p
R36
8
100k
3SK255Q353
G1
D
S
G2
C411
0.1u
R50
4
270
R412
10k
C51
982
p
C23
1
1000
p
C61
0
0.5p
C35
3
0.01
u
R510
1.5kR430
100
L420
150n
R223
4.7k
R30
8
330k
L415
*
C210
0.1u
8R
L507
1T
C42
4
1u16
R53
0
1k
C306
1000p
R42
3*
Q34KRC102S
C60
8
33p
D50
3
02D
Z5.
1(Y
)
L416
C25
4
1u
R52
7
220k
C20
1
0.1u
2SJ243Q202
R43
3
4.7k
R22
4
1k
R41
6
470
R51
4
0
R31
1
33k
R107 47k
L406*
R35
47k
5C
R207
750k
C55
9
0.1u
R36
1.5k
C22
7
0.01
u
R33
47k
X401
L77-1868-15
XOUT
5C
C37 1000p
Q61KRC404RTK
C42
3
0.04
7u35
R60
2
22k
C554
1000p
R77130k(D)
D40
1
MA
2S11
1
R228
10k
R35
9
220k
C466
100p
C26
5
0.1u
R31
0
1k
C28
220p
R53
3
0
R20
2
0
TH
301
100k
R26
0
220k
C31
8
0.1u
IC35PST9140NR
1NC
2VEE1
3VEE2
4
5
5C
C509
15p
C526
680pC432
0.5p
R42
2
10k
R528
470
R410*
C22
9
4.7u
6.3
C459
1000p
C54
2*
C502
1000p
C412
10u6.3
R25
5
5.6k
CN601
8R
C456
2p
R322
100
D35
4
HV
C35
0B
1
2
3
4VEE
5
6
7
8VCC
78
C20
7
0.02
2u
C41
4
0.1u
R211
82k
R265
5.6k
R42
0
2.7k
C16
1
1000
p
R32
1
22k
R26
6
5.6k
R43
612
0k
69
R205
820
8T
C53
0
0.47
u
R20
4
18k
R44
1
100
R215
68k
C35
7
0.01
u
R31
2
47k
C42
2
470p
C26
1
0.01
u
C36
0
1000
p
C42
5
0.1u
35
R267
0
8C
R5160
R444
1k
C50
710
00p
C25
7
0.03
9u
R50
7
10
R44
0
100
D35
3
HV
C35
0B
2SK1824Q253
C26
0
0.01
u
R419
1k
L421
100n
C50
0.01
u
C78
1000
p
R130 1k
TC
402
10p
R43
5
100
5M
C53
6
1000
p
5C
IC33NJM78L05UA
2
COM
3IN
1OUT
C16
3
1000
p
C60
6
0.5p
C26
2
1000
p
86
TC
352
10P
L405
R209
240k
C43
82p
R50
6
10k
R529
470
8C
C61
6
1000
p
L501
68n
R43
1
100k
R35
8
47
TC
351
6P
C36
8
22p
L505*
3SK255Q352
G1
D
S
G2
C36
1000
p
D404
MA2S304
R259
12k
78
R44
3
2.2k
C35
1000
p
8C
R37
1
470k
R165 1k
2SC2412KQ301
C43
7
470p
L419
100n
48
R50
2
270
R23
29.
1k
R43
7
1k
D6081SS355
R42647k
R22
9
680k
C44
9
470p
R523*
C21
1
820p
D302DAN222
R256
5.6k
C23
0
0.1u
R409
100k
C34
330u
25
D602MA4PH633
D40
7
MA
360
R432
1k
R52
5
56k
D40
8
MA
2S11
1 C36
4
1000
p
IC202NJM2904V
12345 6 7 8
V+
R43
8
22k
L604
5T
R50
922
D35
1
HV
C35
0B
R31
4.7k
R26
3
91k
35
R30
9
3.3k
R124
47k
R206
100
R354
330
C203
0.027u
R41
7
220k
D606MA742
R37
0
150
L304
330n
R39
470k
R41
330k
R36
2
470k
R36
5
100k
C54
0.1u
C359
8p
SB
F501
C21
5
0.1u
C23
3
4.7u
6.3
R418
1k
C51
0
8p
C22
8
10u6
.3
D502DA221
C384
1p
R51
9
33k
C52
1000
p
5M
C21
2
1200
p
C56
0
1000
p
C516820p
R415
0
5M
C36
6
0.1u
R37
6
100k
R108 47k
C31
7
0.1u
SB
R40
390k
R22
0
15k
C45
247
0p
R51
8
33
R16
1
1.2k
8R
C40
0.1u
C38
2
22p
C37
5
1000
p
C418
1000p
L602
5T
R531
47k
C371
2p
SB
C41
22u1
0
C30
7
0.02
2u
C37
0
1000
p
R37
3
680k
R36
7
47
C32
4
0.01
u
C603
1000p
R37
5
100k
C45
7
1000
p
L422
56n
C45
5
3p
D35
2
HV
C35
0B
C39
0.1u
5C
D303DAN222
C55
0.1u
C37
8
1000
p
R21
3
330k
IC34PST9140NR
1
2
3 4
5
84
R16
2
1.5k
C45
022
u10
R210
18k
C51
73p
R22
1
15k
8R
C217
10u6.3
R164 1k
C49
0.01
u
C51527p
C46
4
1000
p
C31
6
0.1u
CN21
2
3
4
5
6
7
8
9
10
11
12
C15
470p
C17
470p
CN31 IGN
2 DATAI
3 DETO
4 TXAFI
5 TXAFO
6 EMGMIC
7 RXAFO
8 ALTI
9 RXAFI
10 5C
11 8C
D5
DA
221
D7
DA
221
D9
DA
221
C14
470p
D11
DA
221
D8
DA
221
D4
DA
221
C24
470p
C25
470p
D6
DA
221
C22
470p
C16
470p
C20
470p
C21
470p
C26
470p
C19
470p
C13
470pCN4
1 GND
2 NC
3 NC
4 NC
5 TXDATA
6 NC
7 NC
8 RESET
9 RXDATA
10 SIGOUT(L)
11 VCC
12 NC
13 SIGOUT(H)
14 DISC
15 BEETOUT(H)
16 BEEPOUT(L)
17 IRQ
18 NC
19 NC
20 GND
C23
470p
D10
DA
221
C18
470p
29
30
43
45
46
48
47
49
8
1
8C
5M
R1230
C101
1000p R12
10
C102
0.1u
R12
20
IC401MB15A02
11121314151617181920
C40
2
100p
C40
3
100p
C40
1
100p
R402 1k
C40
4
15u6
.3
R403 1k
R401 1k
R40
5
0
R40
4
10k
C16
4
10u6
.3
R21
9
180k
C21
8
10u6
.3
R21
8
82k
IC203NJM2902V
1
2
3
4V+
5
6
7 8
9
10
11GND
12
13
14R
226
100k
R22
5
150k
C38
9
1000
p
R379
100k
R34
9
47k
C35
0
470p
R35
0
27k
2SK1824Q354
8T
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51525354555657585960616263646566676869707172737475
768RC
778TC
78CM
79NC
80NC
81NC
82SBC
83KMI2
84KMI1
85KMI3
86KMI4
87PWRPRCT
88SIGNAL
89TEMP2
90TEMP1
91BATT
92RSSI
93SQIN
94AVSS
95NC
96VREF
97AVCC
98NC
99KMO1
100KMO2
R118 1k
R119 1k
R116 1k
R117 1k
R115 1k
R113 47k
R114 1k
49
R105 1k
R106 1k
29
30
L401
C40
9
0.1u
C41
010
u6.3
L404
R40
810
C40
8
22p
L403
10u
R40
7
1.5k
C40
6
1000
p
L303
330n
C32
2
56p
L302
330n
C319
100p
C32
3
270p
R414
470
C41
7
1000
p
L411*
L407
*L4
12*
C42
8
470p
C42
7*
C426* L408*
L409
*
C42
9*
L410
*
C45
3
220p
C434*
C43
5*
L413*
L414
*
R42
7
100k
R10
3
1k
17
8C
C45
822
0p
C46
8
220p
C471*
RD55003TRQ503
C52
822
0p
C52
7
1000
p
C54
1*
C54
9
220p
L506
9.5T C
545
1000
pC
546
0.47
uC
574
1000
pC
576
220p
C55
2* C
553
*
C55
0
68p
L508
2.5T
8T
D60
4*
C60
1* D
603
*
C60
5*
C388* R378*
CN1
69
5C
SB
100
R126 1k
R127 1k
83R125 1k
84
86R128 1k
85
2SK1824Q1
5CR5
22k
C10
1000
p
5C
POWER
35
R11047k
5M
R15110k
R163 47k
C269
0.1u
R270
2.7k5M CNVSS
R10
1
47k
R78
1k
5M
R860
2SK1824Q87 C87
18p
C88 6p
X86L77-1934-05C90
18p
C89 6p
R76
18k
(D)
R87 1k
R10
2
47k
R82 0
C83
0.1u C82
1000
p
5M
R92 1k
R93
5.6k
R91 1k
C103
1000p
R94
5.6k
R60
3
47k
C97
1000
p
TH
98
100k
TH
97
100k
C98
1000
p
C29
470p
C30
1000
p
C33
1000
p
B
BS
B
R70
47k
R69 1k
R66
47k
R68 1k
R6747k
C66 1000p5M
R251
47k
C251
4.7u6.3
1
2
3
4V+
5
6
7 8
9
10
11GND
12
13
14
R25
2
470k
C25
2
39p
R253
0
C253
1u
R25
4
680
C27
2
1000
pR27
3
4.7k
D251MA742R
272
1.5k
R27
4
15kC27
1
3300
p
C27
0
4.7u
6.3
R275
15k
R27
1
560
3
7 3
9
7
8
R24
9
47k
R25
0
47k
C25
0
0.1u
5C
C26
7
0.47
u
IC301TK14489V
1
2
3
4
5
6
7
8
9
10 11
12
13
14
15
16
17
18
19
20
C30
5*
R30
3
22k
C315
0.1u
R314 2.2k
C312 0.1u
C30
1
4.7u
6.3
C30
3
4700
p
C31
4
0.01
u
C30
2
1000
p
R315 18k
R306
270k
C30
4*
R30
1
4.7k
R30
2
4.7k
C31
3
15u6
.3
R32
5
33k
L301L34-4554-05
C311 0.1u
R32
4
0
R30
4
4.7k
C32
6
0.01
u
8C
L101 C10
4
0.1u
R129
0
R353
100k
R355*
R36
1*
C367*
C36
9*
L355
*
C37
3*
R37
2*
R37
4*
C38
6*
L356
*
5C
8R
5M
8C
5C
C22
6
4700
p
R43
9
47k
R1 100
R2 0
R3 1k
R4 3.3k
R111 1k
R520
18k
36
R71
4.7kC72
1000
p
1
R72
1M
Q71KRC414RTK
5M
R751k
R73
100k
R74
47k B
D3
DA
221
D1
DA
221
D2
DA
221
C27
94.
7u16
C27
6
1000
p
C27
8
0.1u
C28
1
1000
p
R278
12k
C28
047
u16
12345678910
R28
1
0
Q254DTC363EU
5C
R28
0
390
C28
3
1000
p
C273
1u
R279
4.7k
C27
5
1u
CN5
BS
B
C28
2
470u
16
R27
6
47k
J1
Q255KRC102S
R277
68k
C27
7
1000
p
C274
0.22u
VR
147
k
TH351*
D60
5
XB
15A
709
D501
+
MIC AMP
PLL
E(C
PU
3)
FR
OO
(EV
OL2
3)
X57-6700-XX TX-RX UNIT
DC SWITCH
IF SWITCH
-
8R
BEATSHIFT
-
KEC
KDC
SQL AMP8C
MOD BUFFA
BUFFER AMP
TEMPERATURECOMPENSATION
BUFFERAMP
W/N
I(E
VO
L1)
SURGE ABSORPTION
BEATSHIFT
KEC
AFM(CPU50)
D32
TX/RX(CPU20)
D1-3
-
D31
1/2Vcc
VOLTAGEDETECTORINT
DETECTION
MIC AMP
8R
-
-
DIGITAL
8TC
8C
5C
KEC
+
MO
D
SB
OR GATE
FM DEMODULATION
KEC
TP
1/2Vcc
-
ANT SW
D606,607
VOLTAGEDETECTORRESET
APC VOLTAGEDETECT
8T
PC
+
5M
MIXER
-
-
RF BPF TUNING
SUM AMP
-
+
+
CV
+
CK
(CP
U54
)
1,1A
RX
HPF
B+
MIC
TEMPERATURECOMPENSATION
AGC
TCXO
VOLTAGEDROPPED
+
BUFFER AMP
-
RF AMP
16.8MHz
AFI(EVOL12)
-
DCAMP
AF AMP
+
DT
(CP
U53
)
AUDIOFILTER
+
PRE DRIVE AMP
-
8C
LIPPLEFILTER
RF SWITCH
PLL IC
1/2Vcc
++
SPLATTER FILTER
PLL SYNTHESIZER
RF AMPD351,352
RX VCO
VOLTAGE REGULATOR
-
+
CURRENTPROTECTION
CV
5C
-
REVERSECONNECTIONPROTECTION
E
OVER VOLTAGE
IDC
CHARGE PUMP
INT(CPU18)
+
Q402,403
KEC
POTENTIOMETER
RXD TXD
RESET(CPU10)
INT(CPU18)
Q35,36
Q33,34
SBC(CPU82)
1/2V
cc
Scrambler
Scrambler
8R
8RC(CPU76)
8TC(CPU77)
50.4
MH
z
AFV
D353,354
RF BPF TUNING
RF BPF
EEPROM
IF SWITCH
PRE DRIVE AMP
LIMITTER
TX AF
MIC MUTE
DC SWITCH
DC SWITCH
W/NI(EVOL1)DI
W/N
O(E
VO
L2)
SQIN(CPU93)
5M
5M
5M
RSSI(CPU92)
RESET(CPU10)
TV
KEC
IGNITION
DTMI(EVOL16)
RSSI(CPU92)RSSI(CPU92)
8CL
8CL
AF MUTE
AFO(EVOL11)
AMPSW(CPU52)
AF MUTE
KEC
SPM(CPU51)
R12
00
CLK
NC
3
DAT
ALEFC
NC
4
FO
UTP
NC
5RO
SC
IN
NC
1
OS
CO
UT
VP
VC
C
DO
GN
D
LD NC
2
FIN
VOLTAGEREGULATOR
MIC
AFO(EVOL11)
PC/TV
AMPSW(CPU52)
SMP(CPU51)
8RC(CPU76)
8TC(CPU77)
W/NO(EVOL2)
WIDE(CPU65)
NARROW(CPU64)
AFI(EVOL12)
AMPSW(CPU52)
SMP(CPU51)
SBC(CPU82)
DTMI(EVOL16)
QT/DQT(CPU1)
TX/RX(CPU20)
UL(CPU21)
EVLLD(CPU8)
PLLE(CPU3)
1/2Vcc
IGN(CPU72)
D4-11
SURGE ABSORPTION
2SK1824Q86
DT
MI(
EV
OL1
6)
MO
D
MO
DI(
EV
OL9
)
MO
DO
(EV
OL1
0)
PC
/TV
O(E
VO
L3)
EV
LLD
(CP
U8)
TX
/RX
(C
PU
20)
UL(
CP
U21
)
PC
/TV
DT
MO
(EV
OL1
5)
PLL
E(C
PU
3)
IGN
(CP
U72
)
SB
C(C
PU
82)
IC161M62363FP
AFI(EVOL12)
AFO(EVOL11)
MICEM(CPU74)
MICMT1(CPU73)
IC402UPB1509GV
DIVIDER
SW1
SW2
OUT
VCC2VCC1
IN
IN
GND
XF351
49.95ML71-0591-05
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
DI
CL
CE
5C
SB
KMO2
KMO1
KMI4
KMI3
KMI1
KMI2
CM
HOOK
POWER
PTT
MIC
PC/TV
MIC
8TC(CPU77)
8RC(CPU76)
AFO(EVOL11)
W/NI(EVOL1)
DT(CPU53)
CK(CPU54)
W/NO(EVOL2)
PC
/TV
O
PC
/TV
I
VD
D
LD CLK
DAT
MO
DI
MO
DO
W/N
O
W/N
I
AF
I
AF
O
DT
MI
DT
MO
BLO BLI IN
OU
T
DO
VD
Fref
RE
SE
T
GN
D
FR
QI
FR
QO
SP
M
AM
PS
WDT
CK
NC
NC
DS
T1
DS
T2
DS
T3
VC
C
NC
VS
S
NC
NA
RR
OW
WID
E
NC
NC
NCCL
CEDI
IGN
MIC
MT
1
MIC
EM
MIC
MT
2
EEPWP
EEPCK
EEPDT
FNC1
FNC2
CLKFLS
BSYFLS
TXD
RXD
PTT
HOOK
NC
NC
EMPFLS
NC
NC
NC
FNC3
CEFLS
FNC4
FNC5
FNC7
FNC6
FNC8
AFM
QT
/DQ
T
DT
MF
/MS
K
PLL
E
NC
NC
GN
D
CN
VS
S
EV
LLD
BS
HIF
T
RE
SE
T
XO
UT
VS
S
XIN
VC
C
GN
D
DT
MS
TD
PO
WE
R
INT
NC
TX
/RX
UL
NC
NC
NC
NC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
CF301L72-0993-05
CF302L72-0999-05
QUCO
PH_S
DEC2
DEC1
IF_IN
VCC
MIX_O
NC
OSC(E)
OSC(B)
Hy_C
GND
RFIN
AFO
RSSI
FLAMPI
FLAMPO
SQLIN
SCAN
SCAN
NARROW
DC SWITCH
VOLTAGEREGULATOR
8C
OUT
VCCNC
VEE1
VEE2OUT
VCC
W/N
O(E
VO
L2)
SQ
IN(C
PU
93)
IC251NJM2902V
R30
5
1.8k
SDA
SCL
WP
VCCA0
A1
A2
GND
IC66AT24C64N10SI18
1 2 3 4 5 6 7 8 9 10
2SC4738(GR)Q403
2SA1832(GR)Q402
TX VCOD405,406
D407MODULATION
RX VCOD403,404
2SK508NV(K52)Q406
2SK508NV(K52)Q405
TX VCO
LIPPLEFILTER
LIPPLEFILTER
2SC4617(S)Q440
T/R SW
2SC5108(Y)Q410
BUFFER AMP
T/R SW
2SC5108(Y)Q351
IF AMP
2SC4649(N,P)Q411
RF AMP
FINAL AMP
RD70HVF1-01Q504
DRIVE AMP
IC501TA75W01FU
IC252LA4600
AUDIO AMP
SBC(CPU82)
RESET(CPU10)
INT(CPU18)
1/2Vcc
SQIN(CPU93)
AF MUTE
AF MUTE
DETECTIOND301
MA742WIDE
5
6
7
81
2
3
4
IC10130622MAA-B83GP
CPU
1314151617181920212223241 2 3 4 5 6 7 8 9 10 11 12
2SA1641(S,T)Q31D32
1812L110PR
KTA1664(Y)Q35
2SA1745(6,7)Q33
D61
02DZ18(X,Y)OVER VOLTAGEDETECTION
ANT SW
D603-605
TEMPERATURECOMPENSATION
APC CONTROLLERVOLTAGEPROTECTION
2SC4617(S)Q302
2SC3357Q502
R3 1k
R7
2.7k
L1
J1
C25
0.01
u
R14
2.7k
R11
2.7k
C9
0.01
u
R16
100
R10
2.7k
R1 1k
R20
2.2k
R8
2.7k
C14
0.01
u
C27
0.1u
R2 1k
CP33.9k
C4
0.01
u
R6 1k
R18
4.7k
R13
2.7k
C18 1u
C13
0.01
u
CN1
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
R17
10
C10
0.01
u
R5 1k
Q4KRC102S
Q10KRC102S
C16
0.01
u
IC1BU2090FS
1VSS
2DATA
3CLOCK
4Q0
5Q1
6Q2
7Q3
8Q4
9
10
11
12
13
14
15
16
Q9KRA225S
C8
0.01
u
R192.2k
R4 1k
C11
0.01
u
D13
DA
221
CP43.9k
C15
0.01
u
R12
2.7k
C17
0.01
u
R15
2.7k
R9
2.7k
C12
0.01
u
CM
ME
KMO1
SUPER RED
KMI4
4
LEDC1
P
X54-3460-20 DISPLAY UNIT
CL
1
DI
2
KMI3
PTT
6
KMI2
ME
LEDMON
5C5C
BUSY LIGHT SWITCH
MICBL
CM
HOOK
SB
SUPER AMBERHOOK
LEDC4
LEDC2
SHIFT REGISTER FORLED & MICBL CONTROL
4
ME
HOOK
MICBL
3
5
YELLOW GREEN
LEDG
3PTT
CM
PTT
D1-4
MIC
KEY BACKLIT SWITCH
1
LEDR
KEY BACKLIT
MICBL
Q9,10
D13
5C
KMI1
GND
POWER
2
NORMAL AMBER
8
KMO2
7MIC
LEDPF
LEDC3
MIC
5C
M
2
M
P
4
R
1
3
G
Q5
Q6
Q7
Q8
Q9
Q10
Q11
VDD
D9
B30-2239-05
D8
B30-2239-05
D10
B30-2239-05
D5
B30-2239-05
D11
B30-2237-05
D7
B30-2239-05
D6
B30-2239-05
D12
B30-2240-05
CHANNEL KEY LIGHT
MONITOR KEY LIGHT
SURGE PROTECTION
PROGRAMMABLE KEY LIGHT
BUSY
TRANSMIT
D7-10
D2
B30-2238-05
D4
B30-2238-05
D1
B30-2238-05
D3
B30-2238-05
:KRC414RTK
22p
X57-6700-XX
D251.301,606,607
:KRC102S
NO
67n
:2SJ243:HVC350B
L414
330p
IC201
15n68n
Q254
5p
270n
R522
Q61
12p
1p
D602
L406
Q503
120k
L505
:MA742
L412
D61 Q33
2p
L409 R355
:2SC2412K
27p
33n
8p
:NJM2904V
27u
Q405,406
:2SC5108(Y)
1p
IC66
C471
220
C440
50n
47k
:KRC404RTK
100n
IC401
220k
:2SC3357
7p
L356
Q301
:2SK1824
4.7u
IC202
L410
NO
4p
:2SA1641(S,T)
NO
1k
Q251,302,440IC203,251
Q35 :KTA1664(Y)
18.5n
L407
:30622MAA-B83GP
Q408
C386
:AT24C64N10SI18:2SA1745(6,7)
C541
Q351,410
:RD70HVF1-01
27u
:PD55003TR
27p
Q31
:NJM2100V
Q1,86,87,252,253,354
12p
Q403
Q501,502
:NJM78L05UA
12p
Q352,353
L408 L411
D603,604
47
:DTC363EU
L354
D202
270n
XB15A709
:2SK508NV(K52)
27u
NO
C388
D351-354
470
B57331V2104J
L415
270n
:DAN222
Q71
180k
330p
Q202,407
120k
22p
C434
270n
D31
L355
:2SC4649(N,P)
L413
C427
6p
:MA360
C542C426
D604
C533
:
18p
IC501
0
10p
NO
:1SS355
:PST9140NR
15p68p
IC31
390p
39k
:ZSH5MA27
10p
:UPB1509GVD407
XB15A709
50n
:TA75W01FU
39n
C304
:DAN235E
4p
R523
NO
C435
:1812L110PR
39n
L418
27p 15p
D32
27p
27u
D409
:KIA7808AF
D603
330
:MA4PH633 :2SC4738(GR)
C553
:LA4600
4p
:MB15A02
270n
:NJM2902V
27u
C373
R361
:3SK255
IC32,33
27u
IC101
D402
R372
Q404,411
33p
D201,302,303
IC301
390p
IC34,35
4p
IC252
50n
C429
D503
Q201
270n
IC161
:DA221
:M62363FP
330
IC402
C601
:2SA1832(GR)
R423
:MA2S111
470p
4.7u
D1-11,502
C367 C369
R374
:KRX102U
:MA2S304
67n
C305
5668n
Q504
100p
TH351
C605
:1SS372
270n67n
6p
Q402
24p
33p
:2SC4617(S)
27n
180
D501.608
0.5p
:02DZ18(X,Y)
:HZU5ALL
10
D401,408
Q32.34,36,255
:XB15A709
:02DZ5.1(Y)
D605
R378
:2SC4919
150p
:TK14489V
100p
C552
D403-406
Q4,10 :BU2090FS
D11
D1-4 IC1
:DA221
Q9D5-10
:B30-2240-05
X54-3460-20
:KRC102S
D13
:B30-2239-05:B30-2238-05
:B30-2237-05D12
:KRA225S
X57-6700-XX
M2,K2
M,K
M,K
X57-6700-XX
M2,K2
M2,K2
M,K
X57-6700-XX
*
UL(CPU21)
MOD
MIC
W/NI(EVOL1)
DT(CPU53)
CK(CPU54)
PLLE(CPU3)
W/NO(EVOL2)
R410
10k
8.2k
VC
GND
-23,-25
-22,-24
-22,-24
-23,-25
-22,-24
-23,-25
136-162MHz
146-174MHz
136-162MHz
146-174MHz
146-174MHz
136-162MHz
MBLSBGNDPTTMEMICHOOKCM
TK-7102H TK-7102H
47 48
BLOCK DIAGRAM
Q4402SC4617(S)
DT
Q332SA1745(6,7)BATT
CF302(NARROW)
PREDRIVEAMP
D303DAN222
MICMT2
SW
IC202NJM2904V
8TC
AVR5V
XF35149.95MHz
8RC
D201DAN222
D2021SS372
IC66AT24C64N10SI18
RF
IC402UPB1509GV
DIVIDER
D302DAN222
PC
ANT
Q872SK1824
IC161M62363FP
(3/8)
IC161M62363FP(6/8)
IC161M62363FP
(7/8)
KMO1
BUFF
Vg
D/ACONV
D/ACONV
D/ACONV
BATT
POWER
BUFFER
IGN
Q71KRC414RTK
D301MA742
PLLE
TCXOM0D
AGCDET
INT
KMI1
Vg
KMO2
450kHz
SW
BPF
IC252LA4600
NOISE
D/ACONV
D/ACONV
IC501TA75W01FU(1/2)
IC501TA75W01FU(2/2)
TX-RX UNIT (X57-670x-xx)
CK
SW
WIDE
LOOPFILTER
ANT SW
8C
ELVLLD
SW
POWER
RF
BUFF
Q3512SC5108(Y)
IC203NJM2902V
(1/4)
IC203NJM2902V
(3/4)
VCOMOD
MICMUTE
OVERVOLTAGE
DET
HOOK
8CL
IC201NJM2100V
SW
CF301(WIDE)
D351,352HVC350B
PLL IC
8RC
CK
IC251NJM2902V
Q3533SK255
RF
SBC
TXRX
8C
IC31KIA7808AF
AVR8V
SUM
KMI1
TEMP2
CM
MICMT1
MIX
SW
5M
ME
AFFILTER
TXVCO
SW
MIC
RIPPLEFILTER
IGN
Q4112SC4649(N,P)
Q4102SC5108(Y)
SW
8T
MIC
8CL
D353,354HVC350B
5CBSHIFT
BSHIFT
8R
SW
KMO2
SW
E
D606MA742
HOOK(RXD)
AGC
RESET
Q35KTA1664(Y)
D607MA742
50.4MHz
DTMF
B
DET
SW
8R
Q2012SC4919
IC32NJM78L05UA
5M
SW
VCOMOD
Q4032SC4738(GR)
TCXO
D/ACONV
WIDE
KMI4
NARROW
EEPROM
Q252,2532SK1824
8R
RESET
NARROW
IC33NJM78L05UA
KMI3
MIC
RF BPFTUNE
RF BPFTUNE
SPLATTERFILTER
CPU
IC10130622MAA-B83GP
AVR
CHARGEPUMP
CHARGEPUMP16.8MHz
BPF
Q36KRC102S
Q254DTC363EU
IC161M62363FP(3/8)
IC161M62363FP(4/8)
8T
Q4062SK508NV(K52)
IC35PST9140NR
IC161M62363FP(8/8)
5C
RESETX86
IC161M62363FP(1/8)
IC34PST9140NR
DTMF/BEEP
8TC
SB
SQIN
Q32KRC102S
8C
PTT
SBC
KMI3
Q2512SC4617(S)
PTT(TXD)
8C
MICBL
MIC/IDC
FINALAMP
Q4042SC4649(N,P)
16.8MHz
8C
SPM
MICEM
SIGNAL
PTT(TXD)
Q34KRC102S
CM
8T
DRIVEAMP
SB
+B
IFDEMODULATOR
GND
AFPA
AFM
SW
ME
MCF
INT
Q4072SJ243
D602MA4PH633D603~605XB15A709
SW
8T
IC401MB15A02
8T
LD
Q61KRC404RTK
Q3022SC4617(S)
TRIPLER
DT
INT
KMI4
TEMP1
APCCONTROL
SW
KMO1
HOOK(RXD)
KMI2
TCXOMOD
D/ACONV
CM
CV
5C
Q503PD55003
Q4022SA1832(GR) LPF
KMI2
SB
8R
POW.DET
POW.DET
SW
RF
Q408KRX102U
Q862SK1824
T/RSW
HPF
DTMF
5M
Q3012SC2412K
IF
Q5012SC3357
5C
Q504RD70HVF1
D409DAN235E
EXT.SP
16.8MHz
Q3523SK255
Q312SA1641(S,T)
RXVCO
8R
PLLE
DISPLAY UNIT (X54-3460-20)
SP
Q5022SC3357
Q4052SK508NV(K52)
MICMT
IC1BU2090FS
CLDI
MICBL
POWER
5C
CLDI
Q12SK1824
OVERVOLTAGE
DET
EEPWPEEPCKEEPDT
X401
IC301
SWQ255
KRC102S
AMPSW
Q3542SK1824
SW8T
QT/DQT
TX/RX
FNC2FNC3 FNC4FNC5 FNC6FNC7 FNC8
FNC1
SPMAFM
AMPSW
CLDI
PWRPRCT
RSSI
SQIN
8C
4
KMO1
P
KMO2KMI1 KMI3
M
KMI4KMI2
321
SHIFTREGISTER
LEDMONLEDPFLEDC1LEDC2LEDC3LEDC4LEDRLEDG
KEY
D12
D5
Q9KRA2555S
LEDC4
LEDG
Q10KRC102S
LEDC3
D6
MICBL
D9
D10
2D8
LEDMON
PSB
MON
1LEDC1
4
D11
3
BUSY
PF
SW
D7
SW
RED
LEDC2
LEDR
LEDPF
Q4KRC102S
SW
5C
5C
CE
SBFNC1~FNC8
DETO
EMGMIC
8C
ALTI
TXAFI
5C
IGN
TXAFO
RXAFI
RXAFO
DATAI
5CFNC1(TXD)
DATAI
ALTIDETO2
FNC2(RXD)FNC3(RESET)
GND
TK-7102H TK-7102H
49 50
LEVEL DIAGRAM
S
To make measurements in the RF section, connect the RF Wattmeter (50Ω).
13dBm–5dBm
G2
Q351
14
3
J1
IC201
IC161
D
–7dBm
IC203
Q353 XF1
12
7
Q251
IC202 Q504
To make measurements in the AF section, connect the AC level meter.(ANT input : –53dBm, 1kHz FM, 3kHz DEV (Wide)/1.5kHz DEV (Narrow))The AF output level is adjusted for a 0.45V/4Ω by the front panel AF VOL control.
W : –123.5dBmN : –123.0dBm
W : –119.0dBmN : –118.5dBm
W : –104.5dBmN : –103.5dBm
W : –104.0dBmN : –103.5dBm
W : –112.0dBmN : –111.5dBm
W : 0.49mVrmsN : 0.20mVrms
W : 1.05VrmsN : 0.44Vrms
W : –92.0dBmN : –90.5dBm
W : –77.5dBmN : –74.0dBm
W : –85.0dBmN : –84.5dBm
IC202
BPF BPF 8
6 8
Q406
ANT
X54-346
G2
9
9
1
To make measurements in the RF section, connect the RF level meter.In the RF section, use a 0.01µF coupling capacitor.(The display shows the SSG input value required to obtain 12dB SINAD.)
TX-RX Unit
Q410
18dBm
12
11
G1
4Ω
11
2
Q411
10
FINAL Amp
2
Q503
IC251
2
S7
Q352
10
D409
IC252
TX-RX Unit
S
IC251
Display Unit
IC402
D
Audio Frequency
5
IC161Q501
1
D
TX-RX Unit (VCO)
IC251
MIC
To make measurements in the AF section, connect the AC level meter.AG is set so that MIC input becomes 3kHz/1.5kHz (Wide/Narrow) DEV at 1kHz MOD.
–8dBm
D
CF1/CF2
450kHz
IC251
7
W/N5.0mVrms
W/N0.10Vrms
W/N1.40Vrms
W/N1.16Vrms
W/N1.26Vrms
W/N1.04Vrms
Q502
11
G
IC203
–7dBm
TX-RX Unit
S
IC301
1
5
49.95MHz
D6029G
IC201
50W
G120 3
1 ANT
Center Frequency
W/N0.33Vrms
W/N0.32Vrms
W/N0.26Vrms
W/N0.30Vrms
W/N0.31Vrms
W/N10mVrms
W/N0.50Vrms
W/N0.45Vrms
Receiver Section
Transmitter Section
TK-7102H
51
GENERAL
Frequency Range ............................... K,M : 146 to 174MHz K2,M2 : 136 to 162MHz
Channels / Groups .............................. 4 channels
Channel Spacing ................................. Wide : 25kHz Narrow : 12.5kHz
PLL Channel Stepping ........................ 2.5, 5, 6.25, 7.5kHz
Operating Voltage ............................... 13.6V DC ±15%
Current Drain ...................................... Less than 0.4A on standby
Less than 1.0A on receive
Less than 14.0A on transmit
Operating Temperature Range ........... –30°C to +60°CDimensions & Weight ........................ 6.30 (160) W x 1.70 (43) H x 5.40 (137) D inch (mm), 2.60 lbs (1.18kg)
Channel Frequency Spread ................ 28MHz
RECEIVER (Measurements made per EIA standard EIA/TIA-603)
Sensitivity (12dB SINAD) .................... Wide : 0.28µV Narrow : 0.35µV
Selectivity ........................................... Wide : 75dB Narrow : 65dB
Intermodulation................................... Wide : 70dB Narrow : 60dB
Spurious Response ............................. 75dB
Audio Power Output ........................... 4.0W
Frequency Stability ............................. ±2.5ppm
TRANSMITTER (Measurements made per EIA standard EIA/TIA-603)
RF Power Output ................................ High : 50W Low : 25W
Spurious and Harmonics..................... 70dB
Modulation .......................................... Wide : 16K0F3E Narrow : 11K0F3E
FM Noise ............................................ Wide : 45dB Narrow : 40dB
Audio Distortion .................................. Less than 3%
Frequency Stability ............................. ±2.5ppm
SPECIFICATIONS
KENWOOD CORPORATION2967-3, Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan
KENWOOD U.S.A. CORPORATIONP.O. BOX 22745, 2201 East Dominguez Street, Long Beach, CA 90801-5745, U.S.A.
KENWOOD ELECTRONICS CANADA INC.6070 Kestrel Road, Mississauga, Ontario, Canada L5T 1S8
KENWOOD ELECTRONICS DEUTSCHLAND GMBHRembrücker Str. 15, 63150 Heusenstamm, Germany
KENWOOD ELECTRONICS BELGIUM N.V.Leuvensesteenweg 248 J, 1800 Vilvoorde, Belgium
KENWOOD ELECTRONICS FRANCE S.A.13, Boulevard Ney, 75018 Paris, France
KENWOOD ELECTRONICS U.K. LIMITEDKENWOOD House, Dwight Road, Watford, Herts., WD18 9EB United Kingdom
KENWOOD ELECTRONICS EUROPE B.V.Amsterdamseweg 37, 1422 AC Uithoorn, The Netherlands
KENWOOD ELECTRONICS ITALIA S.p.A.Via G. Sirtori, 7/9 20129 Milano, Italy
KENWOOD IBERICA S.A.Bolivia, 239-08020 Barcelona, Spain
KENWOOD ELECTRONICS AUSTRALIA PTY. LTD.(A.C.N. 001 499 074)16 Giffnock Avenue, Centrecourt Estate, North Ryde, N.S.W. 2113 Australia
KENWOOD ELECTRONICS (HONG KONG) LTD.Unit 3712-3724, Level 37, Tower one Metroplaza, 223 Hing Fong Road, Kwai Fong, N.T., Hong Kong
KENWOOD ELECTRONICS TECHNOLOGIES(S) PTE LTD.Sales Marketing Division1 Ang Mo Kio Street 63, Singapore 569110
TK-7102H