MF

Made in Germany

Service Manual

5314 / 5316Vacuum-Belt Applicator

up to Serial No. 8698

2 2

Family TypeVacuum-Belt Applicator 5314 L-3

5314 R-3

5316 L-3

5316 R-3

Edition: 03/2016 - Part.-No. 9009638

CopyrightThis documentation as well as translation hereof are property of cab Produkttechnik GmbH & Co. KG. The replication, conversion, duplication or divulgement of the whole manual or parts of it for other intentions than its original intended purpose demand the previous written authorization by cab.

EditorRegarding questions or comments please contact cab Produkttechnik GmbH & Co. KG.

TopicalityDue to the constant further development of our products discrepancies between documentation and product can occur.Please check www.cab.de for the latest update. Terms and conditionsDeliveries and performances are effected under the General conditions of sale of cab.

Service Manual for the following products

Germanycab Produkttechnik GmbH & Co KGPostfach 1904 D-76007 Karlsruhe Wilhelm-Schickard-Str. 14 D-76131 KarlsruheTelefon +49 721 6626-0 Telefax +49 721 6626-249www.cab.de info@cab.de

Francecab technologies s.a.r.l. F-67350 Niedermodern Téléphone +33 388 722 501www.cab.de/fr info.fr@cab.de

USAcab Technology Inc. Tyngsboro MA, 01879 Phone +1 978 649 0293www.cab.de/us info.us@cab.de

Asia cab Technology Co., Ltd.

Junghe, Taipei, Taiwan Phone +886 2 8227 3966www.cab.de/tw info.asia@cab.de

China cab (Shanghai)Trading Co., Ltd.

Phone +86 21 6236-3161www.cab.de/cn info.cn@cab.de

Representatives in other countries on request

2 3Table of contentsOperation1 Introduction ............................................................................................................................................ 41.1 Instructions ............................................................................................................................................... 41.2 Intended Use ............................................................................................................................................ 41.3 Safety Instruction ..................................................................................................................................... 41.4 Safety Marking ......................................................................................................................................... 51.5 Environment ............................................................................................................................................. 52 Product Description ............................................................................................................................... 62.1 Important Features ................................................................................................................................... 62.2 Technical Data .......................................................................................................................................... 62.3 Device Overview ..................................................................................................................................... 72.4 Contents of Delivery ................................................................................................................................. 83 Operation ................................................................................................................................................ 93.1 Standard Operation .................................................................................................................................. 93.2 Cleaning ................................................................................................................................................... 94 Error Messages .................................................................................................................................... 104.1 Error Messages of the Printer ................................................................................................................ 104.2 Error messages of the Applicator ........................................................................................................... 105 Licences ................................................................................................................................................ 115.1 Declaration of Incorporation ....................................................................................................................115.2 EU Declaration of Conformity ................................................................................................................. 12Service6 Installation ............................................................................................................................................ 136.1 Standard Settings Ex Factory ................................................................................................................ 136.2 Tools ....................................................................................................................................................... 146.3 Mounting ................................................................................................................................................ 157 Adjustments ......................................................................................................................................... 167.1 Adjust the angle to the printer ............................................................................................................... 167.2 Adjust the pressure roll .......................................................................................................................... 167.3 Adjustment of the Printer Setup ............................................................................................................. 177.4 Signals ................................................................................................................................................... 178 Configuration ........................................................................................................................................ 188.1 Quick Mode for Setting the Delay Times ................................................................................................ 188.2 ConfigurationParametersoftheApplicator ........................................................................................... 188.3 Setting the Peel Position ........................................................................................................................ 198.4 Activation of Peel-off Mode .................................................................................................................... 199 Operation .............................................................................................................................................. 209.1 Test Mode without Print Job ................................................................................................................... 209.2 Test Mode with Print Job ........................................................................................................................ 20Spare Parts / Drawings10 Spare Parts ........................................................................................................................................... 2110.1 Support Assembly / Transport ................................................................................................................ 2110.2 Control Unit / Contact Pressure ............................................................................................................. 2210.3 Fan ......................................................................................................................................................... 2311 Block Diagram ...................................................................................................................................... 2412 Index ...................................................................................................................................................... 25

4 41 Introduction1.1 Instructions

Important information and instructions in this documentation are designated as follows:

Danger!Draws your attention to an exceptionally grave, impending danger to your health or life.

!Warning!Indicates a hazardous situation that could lead to injuries or material damage.

! Attention!Draws attention to possible dangers, material damage or loss of quality.

i Notice! Gives you tips. They make a working sequence easier or draw attention to important working processes.

Environment!Gives you tips on protecting the environment.

Handling instruction

Reference to section, position, illustration number or document.

Option(accessories,peripheralequipment,specialfittings).

Time Information in the display.

1.2 Intended Use• The device is manufactured in accordance with the current technological status and the recognized safety rules.

However, danger to the life and limb of the user or third parties and/or damage to the device and other tangible assets can arise during use.

• The device may only be used for its intended purpose and if it is in perfect working order, and it must be used with regard to safety and dangers as stated in the operating manual.

• The device applicator mounted on a cab printer of the Hermes+ series is intended exclusively for applying suitable materials that have been approved by the manufacturer. Any other use or use going beyond this shall be regarded as improper use. The manufacturer/supplier shall not be liable for damage resulting from unauthorized use; the user shall bear the risk alone.

• Usage for the intended purpose also includes complying with the operating manual, including the manufacturer‘s maintenancerecommendationsandspecifications.

i Notice! The complete documentation can currently be found in the Internet.

1.3 Safety Instruction

!Attention!Initiation,adjustmentsandchangingofpartsisforqualifiedservicepersonalonly.

!Warning!This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

• Before mounting the delivered components disconnect the printer from the power supply and close the shutoff valve at the applicator.

• Only connect the device to other devices which have a protective low voltage.• Switch off all affected devices (computer, printer, accessories) before connecting or disconnecting.• In operation, moving parts are easily accessible.

This applies especially for the zone of belts and fans. During operation do not reach into that zone and keep long hair, loose clothes, and jewelry distant.

4 51 Introduction During operation do not reach into that zone and keep long hair, loose clothes, and jewelry distant. • The device may only be used in a dry environment, do not expose it to moisture (sprays of water, mists, etc.).• Do not use the device in an explosive atmosphere.• Do not use the device close to high-voltage power lines.• Perform only those actions described in this operating manual.

Work going beyond this may only be performed by trained personnel or service technicians.• Unauthorized interference with electronic modules or their software can cause malfunctions.• Otherunauthorizedworkonormodificationstothedevicecanalsoendangeroperationalsafety.• Alwayshaveserviceworkdoneinaqualifiedworkshop,wherethepersonnelhavethetechnicalknowledgeand

tools required to do the necessary work.• There are various warning stickers on the device. They draw your attention to dangers. Warning stickers must

therefore not be removed, as then you and other people cannot be aware of dangers and may be injured.

1.4 Safety Marking

1

Fig.1 Safety marking

1: Risk of injuries by rotating parts !

! Attention!Never remove or cover safety markings! Replace it in case of damage!

1.5 Environment

Obsolete devices contain valuable recyclable materials that should be sent for recycling. Send to suitable collection points, separately from residual waste.

The modular construction of the print module enables it to be easily disassembled into its component parts. Send the parts for recycling.

6 62 Product Description2.1 Important Features

• For operation in a system the I/O interface of the printer can be used.

2.2 Technical Data

Technical data Vacuum-Belt Applicator 5314

Vacuum-Belt Applicator 5316

Label width Hermes+4 mm 20 – 114 –Hermes+6 mm – 50 – 174

Label height mm 70 – 320Product during labeling in motion ¢

Labeling onto the product from the top ¢

from below ¢

sideways ¢

Product height fix ¢

Speed vacuum belt mm/s 100 / 150 / 220 / 300Length vacuum belt mm 390Cycle time about 1) frequency/min. 30

1) Label height 100 mm, print speed 100 mm/s

Table 1 Technical Data

6 72.3 Device Overview

1

6

12

4

5

7 9 108 11

3

2

13

14

15

without cover of the control unit

Fig.2 Overview

1 SUB-D 15 Interface to the printer2 EEPROM3 Interface sensor on board PCB control 4 Sensor5 Pressure roller6 Setting screw roller pressure7 Setting screw stopper roller8 Fan

9 Connector to SUB-D 15 Interface to the printer10 Connectors to the fans11 Motor belts12 Connector motor belts13 Base plate for mounting on printer14 Screws to adjust the angle of the applicator15 Screws to adjust the applicator direction

2 Product Description

8 82 Product Description2.4 Contents of Delivery

2

1

Fig.3 Contents of delivery

1 Applicator mounted 2 Screws to mount on the printer3 Documentation

i Notice! Please keep the original packaging in case the applicator must be returned.

! Attention!The device and printing materials will be damaged by moisture and wetness.

Set up label printer with applicator only in dry locations protected from splash water.

8 93 Operation3.1 Standard Operation

Check all external connections. Load the material. "Operator's Manual" of the printer. Switch on the printer. Press the feed key at the printer.

A synchronization feed is released. The processed labels have to be removed manually. After a few seconds the printer carries out a short backfeed to position the front edge of the next label at the printing line.

i Notice!This synchronizing also has to be carried out when the print job has been interrupted with the cancel key.Synchronizing is not necessary when the print head was not lifted between print jobs. This also applies if the printer was powered off between print jobs.

Start a print job Start the labelling process via PLC interface.

Error messages during labelling process are shown in the display of the printer 4 Error Messages.

3.2 Cleaning

! Attention!Never use solvent and abrasive.

1

3

2

Clean the outside surfaces and transport belts with multi purpose cleaner. area 1

Clean the fan area with a soft brush or/and a vacuum cleaner. area 2

Useglasscleanertocleanthereflexsensor.area3

Fig.4 Cleaning

10 104 Error Messages4.1 Error Messages of the Printer

For detailed information about printer errors (e.g. 'Paper out', 'Ribbon out', etc.) Operator's manual of the printerError treatment :

Clear the error results Press the feed key to synchronize the label feed, remove the peeled labels manually Press the pause key to quit the error state.

After error correction, the print of the label causing the error will be repeated.

4.2 Error messages of the ApplicatorThe following table contains an overview of error messages and their possible causes. It also suggests methods to resolve the problem :

Error Message Possible Cause

Vac. plate empty Label is removed from the waiting position on the pressure roll before the signal START is coming in.

Upper position Labelhasnotreachedtheareaofthereflexsensorafter5secorwasnotdetected.

Table 2 Error messages of the applicator

Error treatment : Clear the error results Press the pause key to quit the error state.

i Notice!In fault check adjustments and settings with help of the Service Manual.

After error correction, the print of the label causing the error cannot be repeated without re-start of the print job. Except at the error " Vac. plate empty" . In this case, the latest label will print again after quit the error with the pause key and then press the Enter button .

Intheapplicationmode"Apply/Print"sendthesignal"Printfirstlabel"orpressthebutton to send a printed labeltothereflexsensorpositionontheapplicator.

10 115 Licences5.1 Declaration of Incorporation

cab Produkttechnik GmbH & Co KG Wilhelm-Schickard-Str. 14 D-76131 Karlsruhe Germany

Declaration of Incorporation

We declare herewith that the following „partly completed machinery“ as a result of design, construction and the version put in circulation complies with the essential requirements of the Directive 2006/42/EC on machinery :Annex I, Article 1.1.2, 1.1.3, 1.1.5, 1.1.6, 1.2.1, 1.3.2, 1.5.2, 1.5.8, 1.6.3, 1.7In the event of any alteration which has not been approved by us being made to any device as designated below, this statement shall thereby be made invalid.

Device: Vacuum-Belt ApplicatorType: 5314 / 5316

Applied EU Regulations: Applied Standards:Directive 2006/42/EC on machinery • EN ISO 12100:2010

• EN ISO 13849-1:2008• EN 60950-1:2006

+A11:2009+A12:2011+A1:2010+A2:2013Other Relevant Directives:• Directive 2014/30/EU relating to electromagnetic compatibility• Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and

electronic equipment

Personauthorisedtocompilethetechnicalfile: Erwin Fascher Am Unterwege 18/20 99610 Sömmerda

Signed for, and on behalf of the Manufacturer :

cab Produkttechnik Sömmerda Gesellschaft für Computer- und Automationsbausteine mbH 99610 Sömmerda

Sömmerda, 17.06.2015

Erwin FascherManaging Director

Theproductmustnotbeputintoserviceuntilthefinalmachineryintowhichitistobeincorporatedhasbeendeclaredinconformity with the provisions of the Directive on machineryThe documents according annex VII part B from the incomplete machinery are created and will commit to state agencies on request in electronic kinds.

12 125 Licences5.2 EU Declaration of Conformity

cab Produkttechnik GmbH & Co KG Wilhelm-Schickard-Str. 14 D-76131 Karlsruhe Germany

EU Declaration of Conformity

We declare herewith that the following device as a result of design, construction and the version put in circulation complies with the relevant fundamental regulations of the EU Rules for Safety and Health. In the event of any alteration which has not been approved by us being made to any device as designated below, this statement shall thereby be made invalid.

Device: Vacuum-Belt ApplicatorType: 5314 / 5316

Applied EU Regulations: Applied Standards:Directive 2014/30/EU relating to electromagnetic compatibility • EN 55022:2010

• EN 55024:2010• EN 61000-6-2:2005

Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment

• EN 50581:2012

Signed for, and on behalf of the Manufacturer :

cab Produkttechnik Sömmerda Gesellschaft für Computer- und Automationsbausteine mbH 99610 Sömmerda

Sömmerda, 17.06.2015

Erwin Fascher Managing Director

12 136 Installation6.1 Standard Settings Ex Factory

i Notice! Theapplicatorisadjustedinastandardconfigurationbythefactory.Adjustmentswiththesevaluesguaranteeasmoothoperationwithsameconfiguration.

i Notice! In case of a customer setup with special material the adjustments can deviate from standard values. Then the values in the setup protocol are valid.

The standard values for the settings ex-factory are: - Connecting on a cab Hermes+ printer, vertical - Used material for ex-factory settings: cab part No.: 5556472 54x35.5

14 146.2 Tools

• Crosstip screwdriver (Phillips)

2 to adjust the sensor

• Hexagon kay L-wrench 2.5 for matched norm parts (in delivery state of the applicator)

3 5

to set the angle of the applicatorto adjust the pressure roll

• Flat-round noise straight

angled

Table 3 Tools

6 Installation

14 156 Installation

Fig.5 Mounting

1 Lay on the printer (1) on the rear side - print unit and material guiding on top.2 Move the applicator (6) so in position to the printer that the holes in the mounting plate (4) are over the holes in

the base of the printer (1) .3 Set on screws (5) and tighten it.4 Connect SUB-D 15 male connector (3) to the female connector (2) of the printer.

!Attention!

Disconnect the printer from the power supply before mounting the applicator ! Ensure a stable standing of the printer !

2

1

3

5

4

6

6.3 Mounting

16 167 Adjustments

i Notice!The right position of the applicator to the printer is adjusted ex factory and is not to change. Adjust only the Degree of the applicator to the printer and the pressure of the pressure roll.

7.1 Adjust the angle to the printer

2

1

max 45°

A5214 ...-2 A= 105 mm531x ...-3 A= 155 mm

Fig.6 Angle to printer

!Warning!Attention if you lose the screws (1 und 2)! Device dump down.

Lose both screws (1 and 2) to adjust the angle and so in follow the depth of the applicator to the printer. Adjust angle or the depth on a product and tighten screws (1 and 2).

7.2 Adjust the pressure roll

2

1

Fig.7 Pressure

With the setting screw (1) it is possible to change the pressure which the label apply on the product.

Adjust the pressure so that the label apply bubble-free over the full area.

Do not damage the product with to much pressure

Settingscrew(2)adjustthelowerpositionoftherollinfineadjustment.

16 177 Adjustments7.3 Adjustments in the Printer Setup

3

2

1

4

Fig.8 Labeltransport/Reflexsensor

Waiting position of the label

The operation mode "Blow" must be selected in the setup. Only with this setting it is possible to change the parameter "Blow time" .

Afterdetectingthelabel(2)bythereflexsensor(1)itwillbetransportedfurtherforadefinedtimetoreachthepressure roll (4). To change this overrun time use the parameter

> Blow time

A higher value causes a longer transport distance. 200 ms equates to 10 mm Setup parameters of the applicator

Overrun of the label

Ifthelabel(2)hasleftthesensorarea(3)itwillbetransportedfurtherforadefinedtimetoapplythelabelcompletelystressless. To change this overrun time use the parameter

> Support delay on

7.4 Signals• With the signal DREE will be started the print and transport to the waiting position of the label.• With the signal START will be started the application of the label on the product.

In the application mode "Apply - Print" the print of the next label starts directly after application of the previous label. In the application mode "Print - Apply" the signal DREE must be sent for each label.

Pin Signal Name Description Activation / Active Statuswithout applicator with applicator

1 DREE - printfirstlabelinmode "Apply-Print"

Switch on +24V between Pin 1 and Pin 25

13 START Print start signalPrecondition: The superior controlhasconfirmedwiththe ETE signal that the previous label has been taken from the peel-off position.

Start of printing and labeling +24V between Pin 13 and Pin 25

Interface description Hermes+

Table 4 Part of the interface description of the label printer Hermes+

18 188 Configuration

8.1 Quick Mode for Setting the Delay TimesOn the applicator it is possible to set the transport speed of the label in four steps.By the parameter Support del. off .Besidethestandardmethodfortheprinterconfigurationthereisaquickmodetoadjustthedelaytimesavailable.

i Notice !The quick mode settings can be made during operation . The changes affect directly the current print job. 1. Press the menu key for at least 2 seconds.

Thefirstdelaytimeappearsonthedisplay.2. Adjust the delay time by pressing the ~ key and � key.3. To switch between the different delay times press the } key.4. To leave the quick setup mode press the | key.

The selected delay times are stored in the printer.

8.2 ConfigurationParameters of the ApplicatorTheconfigurationparametersoftheapplicatorcanbefoundinthemenuSetup > Machine param. .

i Notice! The speed of the belt and the label transport is to set by the parameter Support del. off . The value is displayed in ms and not in real used mm/s.

i Notice! It is necessary to set exact the values of the table . In case of a deviation will used the standard value 100.

Parameter Meaning Default> Support del.

offParameter to set the speed of the belts. Four steps are available.100 ms : 100 mm/s speed of the transport belt150 ms : 150 mm/s speed of the transport belt220 ms : 220 mm/s speed of the transport belt300 ms : 300 mm/s speed of the transport belt

100 ms

Table 5 Applicator parameters

18 198.3 Setting the Peel Position

To optimize the transfer of the labels from the printer to the applicator there two different parameters are available for adjusting the peel position.

! Attention! Firstadjusttheparameter"PeelPosition"intheprinterconfiguration. Following adjust the additional peel-off offset in the software.

It is very important to follow that procedure for a certain start after label loading and for the re-start after error treatment.

Parameter"PeelPosition"intheprinterconfiguration

Check the basic setting in the printer setup. Perform labelling cycles by alternately pressing the feed key and the pre-dispense key „9.1 Test Mode without Print Job“.

Adjust the "Peel Position" in such a way, that the blank labels are peeled-off completely from the liner

Peel-off offset in the software

Check the setting in the software. Perform labelling cycles by repeatedly pressing the the pre-dispense key „9.2 Test Mode with Print Job“

Adjust the peel-off offset in such a way, that the printed labels are peeled-off completely from the liner Programming manual or software documentation.

8.4 Activation of Peel-off Mode

i Notice! For labelling operation activate the peel-off mode in the software.

For direct programming use the P command Programming manual.

8 Configuration

20 209.1 Test Mode without Print Job

! Warning!In operation of the applicator movable parts are accessible. It is particularly in the area of belt and fans.

Do not reach into the zone of the moving parts and keep long hair, loose clothes, and jewelry distant.

2

1

Fig.9 Test mode via Enter key

i Notice! Pleaseusethattestmodetoadjusttheparameter"Peelposition"intheprinterconfiguration.

The whole labelling process can be simulated without the need of a print job or a connection to a computer by alter-nately pressing the feed (2) key and the Enter key (1) :

Press the feed key (2). A blank label is fed. The vacuum from the fans as well as the supporting air (blow tube) are switched on. After the detectingthelabelfromreflexsensor,thesupportingairisswitchedoff.

Press the Enter key (1). The label will moved to the labelling position.

9.2 Test Mode with Print Job

i Notice! Please use that test mode to adjust the peel-off offset in the software.

That method allows to check labelling process with the real print data using the Enter key (1). Send a print job.

The test mode is executed in two half cycles : Press the Enter key (1).

Half cycle 1 A label is printed. The vacuum from the fans as well as the supporting air (blow tube) are switched on. After the label has been picked up by the applicator, the supporting air is switched off.

Press the Enter key (1) again. Half cycle 2 The label will moved to the labelling position.

Ifthelabelismanuallyremovedafterthefirsthalfcycle,thehalfcycle1willberepeatedwhenthepre-dispensekeyis pressed again.

9 Operation

20 2110 Spare Parts10.1 Support Assembly / Transport

Fig.10 Support Assembly / Transport - Spare Parts

No. Part-No. Description PU Serial No.from to

1 5902282.001 Screw DIN7984 M5x20 102 5903041.001 Washer DIN125-A5.3 103 5971488.001 Side Plate 14.1 5971679.001 Support L 14.2 5971507.001 Support R 15 5903059.001 Washer DIN988-10x16x0.5 106 5903054.001 Washer DIN988-10x16x1 107.1 5971492.001 ProfileShaft5314 17.2 5972134.001 ProfileShaft53168.1 5971501.001 ProfileShaftMotorSide5314 18.2 5972253.001 ProfileShaftMotorSide53169 5906309.001 Circular Belt AA=330 4.0x737 1

10.1 5971483.001 Axle 5314 110.2 5972149.001 Axle 5316

No. Part-No. Description PU Serial No.from to

11.1 5971491.001 Motor Shaft 111.2 5972137.00112 5971493.001 Adapter Plate 113 5902016.001 Screw DIN7991-M4x10 1014.1 5971696.001 Ground Plate 5314 L 114.2 5971698.001 Ground Plate 5314 R14.3 5972147.001 Ground Plate 5316 L 114.4 5972179.001 Ground Plate 5316 R15 5971689.001 Flange 116.1 5971682.001 Base Plate 5314 L 116.2 5971692.001 Base Plate 5314 R16.3 5972129.001 Base Plate 5316 L 116.4 5972174.001 Base Plate 5316 R17 5902241.001 Screw DIN7984-M4x10 1018 5902240.001 Screw DIN7991-M5x14 10

22 2210 Spare Parts10.2 Control Unit / Contact Pressure

Fig.11 Control Unit / Contact Pressure - Spare Parts

No. Part-No. Description PU Serial No.from to

6 5903054.001 Washer DIN988-10x16x1 1013 5902016.001 Screw DIN7991-M4x10 1017 5902241.001 Screw DIN7984-M4x10 1019 5903510.001 E-Ring DIN6799-9 1020.1 5971497.001 Foam Roll 5314 120.2 5972146.001 Foam Roll 531621.1 5971498.001 Core 5314 121.2 5972144.001 Core 531622.1 5971674.001 Axle 5314 122.2 5972143.001 Axle 531623 5971495.001 Plate 124.1 5971683.001 Holder L 124.2 5971494.001 Holder R 125 5918211.001 ReflexSensor 126 5971518.001 Cable Sensor 127.1 5971673.001 Adjusting Plate L 127.2 5971509.001 Adjusting Plate R 128 5903040.001 Washer DIN125-A6.4 10

No. Part-No. Description PU Serial No.from to

29 5902375.001 Screw DIN7984-M6x10 1030 5971677.001 Lever 131 5971684.001 Bolt 132 5902536.001 Nut DIN439 M6 1033 5971512.001 Set Screw M6 134 5971687.001 Flange 135 5902459.001 Screw DIN7984-M4x12 1036 5971693.001 Bracket 137 5902358.001 Screw DIN7984-M4x6 1038 5971514.001 Motor 139 5902003.001 Screw DIN912 M3x15 1040 5966468.001 Distance bolt 141 5551173.001 PCB Control 142.1 5971702.001 Cover L 142.2 5971701.001 Cover R 143 5971790.001 Fan 144 5971519.001 Cable Printer Interface 148 5905034.001 Spring 1

22 2310 Spare Parts10.3 Fan

Fig.12 Fan - Spare Parts

No. Part-No. Description PU Serial No.from to

43 5971790.001 Fan 145 5902015.001 Screw DIN7991-M4x35 1046 5902570.001 Nut DIN982-M4 1047 5907065.001 Protective Grid 92x92 1

3x 53146x 5316

24 2411 Block Diagram

41Applicator Control

C

ON

1

CO

N 2

C

ON

6

Fig.13 Block diagram

EEPROM

C

ON

3

CO

N 4

C

ON

5

43 Fan

43 Fan

43 Fan

44 SUB-D 9

Anschluss zum Drucker

38 Motor Belt Unit

26 Sensor

Label Detecting

24 2512 IndexIndexB

Block Diagram ..................................24

C

Cleaning .............................................9Conformity ........................................12Control Unit.......................................22

D

Delay Time........................................18Delay Times ......................................18Delivery...............................................8

E

Environment .......................................5Error Messages ................................10

F

Fan ...................................................23Features .............................................6

I

Incorporation..................................... 11Instruction ...........................................4

M

Mounting ...........................................15

O

Operation ............................................9

P

Parameter .........................................18Peel-off Mode ...................................19Peel Position.....................................19Pressure rol ......................................16Printer Setup.....................................17Print Job ...........................................20

S

Safety Instruction ................................4Safety Marking....................................5Signals ..............................................17Standard Operation ............................9Standard Settings .............................13Support Assembly.............................21

T

Technical Data ....................................6Test Mode .........................................20Tools .................................................14