servicemanuals_lg_tv_plasma_42px2rv_42px2rv service manual.pdf
TRANSCRIPT
-
PLASMA TVSERVICE MANUAL
CAUTIONBEFORE SERVICING THE CHASSIS,READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS : MF-056A
MODEL : 42PX2RV42PX2RV-TA
website:http://biz.LGservice.come-mail:http://www.LGEservice.com/techsup.html
-
- 2 -
CONTENTS
SAFETY PRECAUTIONS ....................................................................................3
DESCRIPTION OF CONTROLS ..........................................................................4
SPECIFICATIONS................................................................................................8
ADJUSTMENT INSTRUCTIONS .......................................................................10
TROUBLE SHOOTING GUIDE..........................................................................14
BLOCK DIAGRAM.............................................................................................23
EXPLODED VIEW..............................................................................................24
EXPLODED VIEW PARTS LIST ........................................................................25
REPLACEMENT PARTS LIST...........................................................................26
SCHEMATIC DIAGRAM.........................................................................................
PRINTED CIRCUIT BOARD ..................................................................................
-
- 3 -
SAFETY PRECAUTIONS
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by inthe Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual toprevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used duringthe servicing of a receiver whose chassis is not isolated fromthe AC power line. Use a transformer of adequate power ratingas this protects the technician from accidents resulting inpersonal injury from electrical shocks.
It will also protect the receiver and its components from beingdamaged by accidental shorts of the circuitry that may beinadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this monitor is blown, replaceit with the specified.
When replacing a high wattage resistor (Oxide Metal FilmResistor, over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Due to high vacuum and large surface area of picture tube,extreme care should be used in handling the Picture Tube.Do not lift the Picture tube by its Neck.
Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source,connect an electrical jumper across the two AC plug prongs.Place the AC switch in the on position, connect one lead ofohm-meter to the AC plug prongs tied together and touch otherohm-meter lead in turn to each exposed metallic parts such asantenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, themeasured resistance should be between 1M and 5.2M. When the exposed metal has no return path to the chassis thereading must be infinite.An other abnormality exists that must be corrected before thereceiver is returned to the customer.
Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitorbetween a known good earth ground (Water Pipe, Conduit, etc.)and the exposed metallic parts.Measure the AC voltage across the resistor using ACvoltmeter with 1000 ohms/volt or more sensitivity.Reverse plug the AC cord into the AC outlet and repeat ACvoltage measurements for each exposed metallic part. Anyvoltage measured must not exceed 0.75 volt RMS which iscorresponds to 0.5mA.In case any measurement is out of the limits specified, there ispossibility of shock hazard and the set must be checked andrepaired before it is returned to the customer.
Leakage Current Hot Check circuit
1.5 Kohm/10W
To Instrument'sexposed METALLIC PARTS
Good Earth Groundsuch as WATER PIPE,CONDUIT etc.
AC Volt-meter
IMPORTANT SAFETY NOTICE
0.15uF
-
POWERMUTE
TV/AV MULTIMEDIA
LIST ARC MENU
PR
PR
VOLOK
1 2 3
4 5 6
7
PSM SSM
8 9
0
VOL
PIP/DW SLEEP
REVEAL TEXT/PIP PR+
WIN. SIZE MIXPIP PR-
POSITION TIMESWAP
HOLD INDEXPIP INPUT
?
i
I/II
MULTIMEDIASelects the Component, RGB or
HDMI modes.switches the set on from standby.
PIP/DWSwitches the sub picture on or off.
Selects PIP or DW modes.PIP PR + /-
Selects a programme for the sub picture.SWAP
Alternates between main and sub pic-ture.
PIP INPUTSelects the input mode for the sub pic-
ture.WIN.SIZE
Adjusts the sub picture size.POSITION
Moves the sub picture to DD / EE or FF / GGdirection.
POWERswitches the set on from standby oroff to standby.
ARC Changes the picture format.
MENUDisplays on screen menus one byone.Exits the current menu.Memorizes menu changes.
SWAPReturns to the previously viewedprogramme.Note : This function works onlywhen Favourite programme is setto Off. Otherwise each press of thisbutton will select a stored favoriteprogramme.
SSMTo select the sound appropriate toyour viewing programme.
NUMBER buttons
SLEEPSets the sleep timer.
I/IISelects the language during dual lan-guage broadcast.Selects the sound output.
TEXT/*These buttons are used for teletext.
For further details, see the Teletextsection.Note : In teletext mode, the PIP PR+/-, SWAP and PIP INPUT buttons areused for teletext function.
LISTDisplays the programme table.
TV/AVSelects the TV, AV, Component, RGB
or HDMI modes.switches the set on from standby.
MUTESwitches the sound on or off.
DD / EE (Programme Up/Down)selects a programme or a menu item.
switches the set on from standby.FF / GG (Volume Up/Down)
adjusts the volume.adjusts menu settings.
OKaccepts your selection or displays the
current mode.
PSMAdjusts the factory preset picture
according to the room.
No function
- 4 -
DESCRIPTION OF CONTROLS
-
- 5 -
ON/OFF
TV/AV MENU VOL PR
Main Power Button
Remote Control Sensor
TV/AV ButtonSelects the TV, AV, Component,RGB or HDMI modes. If OSD isdisplayed, selects menu item.
MENUDisplays on screen menus one by one.Exits the current menu.Memorizes menu changes.
DD / EE (Programme Up/Down)selects a programme or a menu item.
switches the set on from standby.FF / GG (Volume Up/Down)
adjusts the volume.adjusts menu settings.
Power Standby IndicatorIlluminates red in standbymode, Illuminates greenwhen the set is turned on
-
- 6 -
S-VI
DEO
VID
EOAU
DIO
RL/M
ONO
A/V 2A/V 2
AC INPUT
RS-232C INPUT(CONTROL/SERVICE)
S-VIDEOS-VIDEO(MONO)
AUDIO AUDIO
L R
AUDIO AUDIO
L R
AUDIO AUDIO
L R
Antenna
VIDEO VIDEO
REMOTECONTROL
HDMI/DVI(VIDEO) AUDIO INPUT RGB INPUT
VIDEOVIDEO
COMPONENTCOMPONENT INPUT INPUT 2 2
COMPONENTCOMPONENT INPUT INPUT 1 1
MONITMONITOR OUTPUTOR OUTPUT
A/V INPUTA/V INPUT 1 1
VVARIABLE ARIABLE AUDIO OUTAUDIO OUT
1. HDMI(DVI VIDEO) / AUDIO INPUT / RGB INPUTConnect the monitor output socket of the PERSONAL COM-PUTER, DVD or STB to this socket.Note: If you want to use RGB/DVI audio, we strongly recommend that you use the cable that has a core, or theEMI Filter core along with separate cable.
2. REMOTE CONTROL
3. RS-232C INPUT(CONTROL/SERVICE) PORTConnect to the RS-232C port on a PC.
4. COMPONENT INPUTConnect DVD video outputs to Y, PB, PR of COMPONENTINPUT and audio outputs to Audio sockets of AUDIO INPUT.
5. VIDEO/AUDIO IN/OUT SOCKETS (A/V INPUT 1)Connect the video/audio out sockets of external equipmentto these sockets.S-VIDEO/AUDIO IN SOCKETS Connect the S-VIDEO out socket of an VCR to the S-VIDEOsocket. Connect the audio out sockets of the VCR to the audio sock-ets as in A/V INPUT 1.
6. VARIABLE AUDIO OUTPUT
7. ANTENNA INPUT
8. POWER CORD SOCKETThis Monitor operates on AC power. The voltage is indicatedon the Specifications page. Never attempt to operate the set onDC power.
9. AUDIO/VIDEO INPUT (A/V 2)S-VIDEO/AUDIO IN SOCKETS
1 42 3 5 7 86
9
-
- 7 -
AS mark
LG TV
Owners Manual
1.5V1.5V
Alkaline batteries Power Cord
POWERMUTE
TV/AV MULTIMEDIA
LIST ARC MENU
PR
PR
VOLOK
1 2 3
4 5 6
7
PSM SSM
8 9
0
VOL
PIP/DW SLEEP
REVEAL TEXT/PIP PR+
WIN. SIZE MIXPIP PR-
POSITION TIMESWAP
HOLD INDEXPIP INPUT
?
i
I/II
Remote Control handset
- Optional extras can be changed or modified for quality improvement. Without any notification new optional extras can beadded.
- Contract your dealer for buying these items.
Optional Extras
Accessories
Tilt wall mounting bracket Video cables Audio cablesCeiling mounting bracket
40
4250
42
40
- Secure the set assembly by fixing it to a wall by using the Eye Bolts/Wall brackets.Fixing the set assembly to the wall to protect the set tumbling
If the set is mounted on a desk top, insert the 2 Eye-Bolts and tighten themsecurely in the upper holes as shown.Insert the 2 Eye Bolts and tighten securely, in the holes on the bracket. Install the wall brackets on the wall with 2 bolts, (not supplied with the product),as shown.Match the height of the Eye Bolts and the wall brackets. Check to be sure the brackets are tightened securely.
Secure the TV assembly to the wall with strong strings or wound wire cables,(not supplied with the product), as shown.
2-Wall brackets
2-Eye Bolts
-
SPECIFICATIONSNOTE : Specifications and others are subject to change without notice for improvement.
- 8 -
V Application RangeThis spec is applied to the 42PDP TV used MF-056A Chassis.
V SpecificationEach part is tested as below without special appointment.1) Temperature : 255C (779F), CST : 4052) Relative Humidity: 6510%3) Power Voltage: Standard Input voltage (100-240V~, 50/60Hz)
* Standard Voltage of each product is marked by models.4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM.5) The receiver must be operated for about 20 minutes prior to the adjustment.
V Test Method1) Performance : LGE TV test method followed.2) Demanded other specification
Safety: CE, IEC specificationEMC : CE, IEC
V General Specification1. Module Specification
Remark
Safety : IEC60065, EMI : CISPR13
Model Name
42PX2RV-TA
Market
Non-EU
Remark
PDP
LGE SPEC
Maker : SONY/ Sanken
Specification
42 inch wide Color Display Module
16:9
PDP42V7xxxx
RGB Closed Type, Film Filter
1) Temp : 0~40 deg2) Humidity : 0~85%1) Temp : -20~60 deg2) Humidity : 0~85%100-240V~, 50/60Hz
No
1
2
3
4
5
6
Item
Display Screen Device
Aspect Ratio
PDP Module
Operating Environment
Storage Environment
Input Voltage
-
2. Model Specification
- 9 -
Item
Market
Broadcasting system
Available Channel
Receiving system
Video Input (2EA)Video Output (1EA)S-Video Input (2EA)Component Input(2EA)RGB Input(1EA)
HDMI Input(1EA)
Audio Input(5EA)Wired Control
Audio variable out
No
1
2
3
4
5
6
7
8
9
10
11
12
13
Specification
Non-EU
PAL B/G/I/D/K, NTSC
BAND PAL NTSC
VHF/UHF C1~C69 2~83
CATV S1~S47 1~71
Upper Heterodyne
PAL, SECAM, NTSC
PAL, SECAM, NTSC
PAL, SECAM, NTSC
Y/Cb/Cr, Y/Pb/Pr
RGB-PC
RGB-DTV
HDMI-PC
HDMI-DTV
PC Audio, Component(2EA), AV(2EA)
Remark
4 System : PAL, SECAM, NTSC,PAL60
4 System : PAL, SECAM, NTSC,PAL60
4 System : PAL, SECAM, NTSC,PAL60
L/R Input
-
- 10 -
ADJUSTMENT INSTRUCTIONS1. Application Object
These instructions apply to the MF-056A Chassis.
2. Specification(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolationtransformer will help protect test instrument.
(2) Adjustment must be done in the correct order.(3) The adjustment must be performed in the circumstance of
255C of temperature and 6510% of relative humidity ifthere is no specific designation.
(4) The input voltage of the receiver must keep 100-220V,50/60Hz.
(5) The receiver must be operated for about 15 minutes priorto the adjustment.
O After RGB Full white HEAT-RUN Mode, the receiver mustbe operated prior to adjustment.
O Enter into HEAT-RUN MODE1) Press the POWER ON KEY on R/C for adjustment.2) OSD display and screen display 100% full WHITE
PATTERN.
[ Set is activated HEAT-RUN without signal generator inthis mode.
[ Single color pattern(RED/BLUE/GREEN) of HEAT-RUN mode uses to check PANEL.
Caution) If you turn on a still screen more than 20 minutes(Especially digital pattern, cross hatch pattern), afterimage may be occur in the black level part of thescreen.
3. Channel memory3-1. Setting up the LGIDS
1) Install the LGIDS. (idsinst.exe)2) After installation, restart your PC.3) Extract [files.zip] to folder [c:\LGIDS\files].4) Start LGIDS.
3-2. Channel memory Method 1) Select PDP and Hurricane on Model dialog. And check
your connection in Communication dialog. (If yourconnection is NG, then set your PORT(COM1,2,3,...)correctly.)
2) Connect RS-232C cable and turn on the power.(If your connection has completed, you can see Ready.)
[ If your set is not an end products but only a board, youhave to make your board to Stand-by state (LED_R). Andyou have to Download in Stand_by power state.
3) Select proper CH_memory file(*.nvm) for each model at[NVRAM Download] $ [Write Batch]Next, select proper binary file(*.bin) including the CHinformation for each model at [NVRAM File].
4) Click the [Download] button.It means the completion of the CH memory download if allitems show OK and Status is changed by PASS at thelower right corner of the window.
5) If you want to check whether the CH information ismemorized correctly or not, click the [Verify] button. And then compare NVRAM File(*.bin) with the CHinformation downloaded.
3-3 Sub program download1) Select PDP and Hurricane on Model dialog. And check
your connection in Communication dialog. (If yourconnection is NG, then set your PORT(COM1,2,3,...)correctly.)(Fig. 1)
(Fig. 3)
(Fig. 3-1)
-
- 11 -
2) Connect RS-232C cable and turn on the power. (Use thespecial Cable For Sub-program) (If your connection hascompleted, you can see Ready)
4. POWER PCB Assy Voltage Adjustments (Va, Vs Voltage Adjustments)
4-1. Test Equipment : D.M.M. 1EA4-2. Adjustment Method
(1) Va Adjustment1) After receiving 100% Full White Pattern, HEAT RUN.2) Connect + terminal of D.M.M to Va pin of P807, connect
- terminal to GND pin of P807.3) After turning RV501, voltage of D.M.M adjustment as
same as Va voltage which on label of panel right/top.(Deviation; 0.5V)
(2) Vs Adjustment1) Connect + terminal of D.M.M to Vs pin of P807, connect
terminal to GND pin of P805.2) After turning RV401, voltage of D.M.M adjustment as
same as Va voltage which on label of panel right/top.(Deviation; 0.5V)
5. EDID (The Extended DisplayIdentification Data)/ DDC (DisplayData Channel) download
5-1. Required Test Equipment1) Adjusting PC with S/W for writing EDID Data.(S/W : EDID
TESTER Ver.2.5)2) A Jig for EDID Download3) Cable : Serial(9Pin or USB) to D-sub 15Pin cable, D-sub
15Pin cable, DVI to HDMI cable
5-2. Setting of device
5.3. Preparation for Adjustment1) As above Fig. 5, Connect the Set, EDID Download Jig, PC
& Cable.2) Turn on the PC & EDID Download Jig. And Execute the
S/W : EDID TESTER Ver,2.53) Set up S/W option
Repeat Number : 5Device Address : A0PageByte : 8
4) Power on the Set
5.4. Sequence of Adjustment(1) DDC data of Analog-RGB
1) Init the data
2) Load the EDID data.(Open File)[Analog-RGB : MF056A_RGB.ANA][digital(HDMI) : MF056A_DMI.DVI]
3) Set the S/W as below.4) Push the Write Data & Verifybutton. And confirm Yes.5) If the writing is finished, you will see the OK message.
Each PCB assembly must be checked by check JIG set.(Because power PCB Assembly damages to PDP Module,especially be careful)
(Fig. 4) Connection diagram of power adjustment for measuring
(Fig. 5) Connection Diagram of DDC download
-
- 12 -
6. Auto AV(CVBS) Color Balance6-1. Required
- This AV color balance adjustment should be performed beforwhite Balance Adjustment
6-2. Required Equipment1) Remote controller for adjustment2) AV Pattern Generator
: 802F Pattern Generator, Master(MSPG-925FA), etc(Which has PAL Composite Video format output withstandard(1.0 Vpp) Vertical 100% Color Bar Pattern as Fig6)
6-3. Method of Auto Color Balance1) Input the PAL Composite Video (Fig6. 100% Color Bar
Pattern) into video input.(42PX4RV-TA : AV1/AV2 Input 50Hz,42PX4RV-ZA : AV4/AV5 Input)
2) Set the PSM to Standard mode in Picture menu.3) Press INSTAR key on R/C for adjustment.4) Press the G(Vol. +) key operate to set, then it becomes
automatically.5) Auto-RGB OK means completed adjustment.
7. Adjustment of White Balance7-1. Required Equipment
1) Remote controller for adjustment2) Color Analyzer (CA-100 or same product)3) Auto W/B adjustment instrument(only for auto adjustment)4) AV Pattern Generator
7-2. Connecting diagram of equipment formeasuring (For Auto Adjustment)
W Auto adjustment Map(RS-232C)
7-3. Adjustment of White BalanceO Operate the zero-calibration of the CA-100, then stick
sensor to PDP module surface when you adjust.O For manual adjustment, it is also possible by the following
sequence.
1) Select white pattern of heat-run mode by pressing poweron key on remote control for adjustment then operate heatrun more than 15 minutes.
2) As below Fig.7-1, Supply 216Level (85 IRE) full screenpattern to Video input.(42PX4RV-TA : AV1/AV2 INPUT 50Hz,42PX4RV-ZA : AV4/AV5 INPUT)
3) Press the TV/AV KEY on R/C for converting input mode.4) Set the PSM to Standard mode in Picture menu.5) Enter the White Balance adjustment mode by pressing the
INSTART key twice(White Balance) on R/C.6) Stick sensor to center of the screen and select each items
(Red/Green/Blue Gain and offset) using D / E(CH +/-) keyon R/C.
7) Adjust Only High Light with R Gain/ B Gain using F / G(VOL+/-) key on R/C.
8) Adjust it until color coordination becomes as below.(High Light G Gain : 7A // Low Light R Offset : 7F, G Offset7E, B Offset 80 is Fixed)[MF-056A : 42PX4RV-TA/ZA] - VGA 42Bright : High Light : 80 20cdColor-Coordinate : High Light : X : 0.285 0.003
Y : 0.295 0.003Color Temperature : 9,300K 500K
9) When adjustment is completed, Exit adjustment modeusing EXIT key on R/C
(Fig. 7-1) Pattern for Adjustment of White Balance
216 Level (85 IRE)
Type
Baud Rate
115200
Index
R GainG GainB Gain
R OffsetG OffsetB Offset
Data bit
8
Cmd1 Cmd2j aj bj cj dj ej f
Stop bit1
Parity
NONE
MF-056A : RT-42PX40/ RZ-42PX40
ProtocolSetting
Data Min Value
00(00)00(00)00(00)00(00)00(00)00(00)
Max Value
255(FF)255(FF)255(FF)255(FF)255(FF)255(FF)
(Fig. 6) Auto AV(CVBS) Color Balance Test Pattern
(Fig. 7) Connection Diagram of Auto W/B adjustment
MSPG-2100 /MSTG- 5200
216 Level (85 IRE)
COLORANALYZERTYPE ; CA-100
CVBSsignalinput
RS-232C Serial Communication
-
- 13 -
8. Auto Component Color Balance8-1. Required Test Equipment
1) Remote controller for adjustment2) 802F Pattern Generator
(Which has 720p Ypbpr output & PC 1024x768 60Hz withStandard(0.7Vpp) Vertical 100% Color Bar Pattern as Fig.8)
8-2. Method of Auto Component Color Balance1) Input the Component 720p 100% Color Bar signal into
Component1 or Component2.2) Set the PSM to Standard mode in Picture menu.3) Press INSTART key on R/C for adjustment.4) Press the G(Vol. +) key operate To set, then it becomes
automatically.5) Auto-RGB OK means complete adjustment
9. Auto RGB Color Balance9-1. Required Test Equipment
1) Remote controller for adjustment2) 802F Pattern Generator, Master (MSPG-925FA), etc.
(Which has XGA 60Hz PC Format output with standard(0.7Vpp) horizontal black and white pattern as Fig.10)
9-2. Method of Auto RGB Color Balance1) Input the PC 1024x768 60Hz horizontal black and white
pattern into RGB.2) Set the PSM to Standard mode in Picture menu.3) Press ADJ key on R/C for adjustment.4) Press the G(Vol. +) key operate To set, then it becomes
automatically.5) Auto-RGB OK means completed adjustment.
9. Default Value in Adjustment mode9-1. Auto Color Balance (Component/RGB)
9-2. White Balance
Level : 0
Level : 255
(Fig. 9) Auto RGB Color Balance Test Pattern
(Fig. 10) Default Value on OSD
(Fig. 10-1) Default Value on OSD
Auto Color Balance(Hex)Auto-RGB G To SetRed Offset1 22Green Offset1 24Blue Offset1 23Red Offset2 45Green Offset2 43Blue Offset2 37Red Gain 14Green Gain 31Blue Gain 11Reset G To Set
White Balance(Hex)Red Gain 82Red Offset 7AGreen Gain 86Green Offset 7FBlue Gain 7EBlue Offset 80Reset G To Set
(Fig. 8) Auto Component Color Balance Test Pattern
-
- 14 -
TROUBLE SHOOTING GUIDE
1. Power Board 1-1. The whole flowchart which it follows in voltage output state
Start check
Manufacture enterprisemeaning of a passage
1. Check the Power Offcondition.
Doesn't the screen whole come
out?
Is it identical with Power Off
condition?
Yes
Yes
No
No
No
No
No
2. Check the Interfacesignal condition.
Is the Interface signal operated?
Yes
3. Check the St-by 5Vsignal circuit.
Doesn't the low pressure output
come out?
Doesn't the St-by 5V signal
come out?
Yes
Yes
No
4. Check the 5V Monitorsignal circuit.
Doesn't the 5V Monitor signal
come out?
Yes
7. Check the VSC Vs-ONsignal
Doesn't the high tension output
come out?
Doesn't the VSC signal Vs-ON
come out?
Yes
Yes
Doeshigh tension
output voltage Dropoccur?
When theY B/D Module
input connector isremoved, does output
voltage dropoccur?
When theY, Z B/D Module
input connector is remove,does Power Board hightension
output voltage Dropoccur?
Yes No No
9. Check the PowerBoard Output high
tension circuit
Yes
10. Check the Z B/DModule output circuit
Yes
When theZ B/D Module
input connector isremoved, does output
voltage Drop occurs?
11. Check the Y B/DModule output circuit
Yes
No
8. Check the Vs, Vavoltage output circuit.
Doesn't the Vs, Va voltage output
come out?
Yes
No
No
5. Check the VSC RL-ONsignal.
Doesn't the VSC signal RL-ON
come out?
Yes
6. Check the VSC lowpressure output
Doesn't the VSC low pressureoutput come out?
Yes
-
- 15 -
1-2. Sony Power Board Structure
1 2 3
T502: Vs TransT702: Va TransT101: St-by TransT103: Low Voltage Trans
-
- 16 -
1-3. Sanken, LG INNOTEK Power Board Structure
1 2 3
T221: Vs TransT271: Va TransT121: St-by TransT201: Low Voltage Trans
-
- 17 -
2. No Power(1) Symptom
Doest minute discharge at module. Non does not come in into the front LED.
(2) Check following
Is plug in power cord? Plug in power cord.
Yes
No
Is the Line Filter and PowerBoard Cable connected? Connect the Cable.
Yes
No
Is the Fuse(F101) onPower Board normal? Replace the Fuse.
Yes
No
Is the Power Board and 7P ofVSC Board Cable connected? Connect the Cable.
Yes
No
After the cable connect is remvedto Power Board(except the CN101connection cable), the AC voltagemarking is authorized on manual.When ST-BY 5V is not operated,replace Power Board.
-
- 18 -
3. Protect Mode(1) Symptom
After once shining, it does not discharge minutely from module
The Rely falls(The sound is audible click) It is converted with the color where the front LED
is red from green.
(2) Check following
Is the Power Boardnormal ?
Replace PowerBoard.
Is output the normality Low/Highvoltage except Stand-by 5V?
Yes
No No
Is the each connectornormal?
Replace theconnector.
ReplaceY-Board.
After connecting well each connector,the normality it operates?
Yes
No No
Is the Ctrl Boardnormal?
ReplaceX-Board.
Is the output voltage normal afterremove P1, 2, 4, 9, 10 connector of
Ctrl-B/D?Yes
No Yes
Is the Y-Boardnormal?
Is the output voltagenormal after removeP5, P6 connector of
Y-B/D?
Is the Fuse(FS2) on Y-B/D normal?(In case of open is replace)
Yes
No Yes Yes
ReplaceZ-Board.
Is the Z-Boardnormal?
Is the output voltagenormal after removeP1 connector of Z-
B/D?
Is the Fuse (FS1, FS2) on Z-B/Dnormal? (In case of open is replace)
Yes
No Yes
Is the X- Boardnormal?
Is the output voltage normal afterremove P1, 2, 3, 4, 5 connector of
X-B/D?
After remove P1, P2, P3 output voltagenormality: Replace Right X-B/DAfter remove P4, P5 output voltagenormality: Replace Left X-B/D
Yes
No Yes
Is the VSC Board normal?
Is the output voltage normal afterremove P1001, P1100?
After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.
After remove P1001, 1100 normaloperation: Replace VSC Board
Yes
No
Is the COF of X, Y, Znormal ?
No
Yes
Yes
-
- 19 -
4. No Raster(1) Symptom
Doest minute discharge at module. It maintains the condition where the front LED is green.
(2) Check following
Is the Power Boardnormal?
Replace thePower Board.
Is output the normality Low/Highvoltage except Stand-by 5V?
Yes
No No
Is the each connectornormal?
Replace theconnector.
ReplaceY-Board.
After connecting well each connector,the normality it operates?
Yes
No No
Is the Ctrl Board normal?
ReplaceX-Board.
Is the output voltage normal afterremove P1, 2, 4, 9, 10 connector of
Ctrl-B/D?Yes
No Yes
Is the Y-Boardnormal?
Is the output voltagenormal after removeP5, P6 connector of
Y-B/D?
Is the Fuse(FS2) normal on Y-B/D?(In case of open is replace)
Yes
No Yes Yes
ReplaceZ-Board.
Is the Z- Board normal?
Is normal the outputvoltage after remove
P1 connector of Z-B/D?
Is the Fuse(FS1, FS2) normal onZ-B/D? (In case of open is replace)
Yes
No Yes
Is the X- Board normal?
Is the output voltage normal afterremove P1, 2, 3, 4, 5 connector of
X-B/D?
After remove P1, P2, P3 output voltagenormality: Replace Right X-B/DAfter remove P4, P5 output voltagenormality: Replace the Left X-B/D
Yes
No Yes
Is the VSC Board normal?
Is the output voltage normal afterremove P1001, P1100?
After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.
After remove P1001, P1100 normaloperation: Replace the VSC Board
Yes
No
Is the COF of X, Y, Znormal?
No
Yes
Yes
-
- 20 -
5. In case of occurring strange screen into specific mode5-1. In case the OSD does not displayed
(1) Symptom LED is green The minute discharged continuously becomes accomplished from module
(2) Check following
Is the LVDS cablenormal ?
Is the VSC Boardnormal?
Is the LVDS cableconnected well?
Cable inserts well.Yes
No
No
Yes
Does the FIL8532 IC(IC800) Operates ?
Replace FIL8532IC(IC800).
No
Is the Ctrl Board ofModule normal? Replace Ctrl B/D.
No
No
YesReplace VSC B/D
Replace the cable.Yes
-
- 21 -
5-2. In case of doest display the screen into specific mode(1) Symptom
The screen does not become the display from specific input mode(RF, AV, Component, RGB, DVI).
(2) Check following Check the all input mode should become normality display. Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become
normality display from the PIP mode or DW mode. (Re-Check it Swap)
(3) In case of becomes unusual display from RF mode
(4) In the case of becomes unusual display from RF, AV mode
(5) In the case of becomes unusual display from Component, RGB mode
(6) In the case of becomes unusual display from HDMI mode
Is the Tuner normal?
Is the CXA2069Qnormal?
Is the Tuner Cableconnected well?
Cable inserts well.Yes
No
No
Yes
Is the FIL8532normal?
Replace the Tuner
No
Is the Input voltage, IIC Communicationand CVBS output normal?
Yes
Is the Input voltage, IICCommunication and HV sync
normal?
NoReplace the IC
No
Is normal the Input voltage, IICCommunication and HV sync?
NoReplace the IC
No
Is the CXA2069Qnormal?
Yes
Is the FIL8532normal?
Is the Input voltage, IICCommunication and HV sync
normal?
NoReplace the IC
No
Is the Input voltage, IICCommunication and HV sync
normal?
NoReplace the IC
No
Is the FIL8532normal?
Is the Input voltage, IICCommunication and HV sync
normal?
NoReplace the IC
No
Is the Sil9011normal?
Yes
Is the FIL8532normal?
Is the Input voltage, IICCommunication and HV sync
normal?
NoReplace the IC
No
Is the Input voltage, IICCommunication and HV sync
normal?
NoReplace the IC
No
-
- 22 -
6. In case of no sound(1) Symptom
LED is green Screen display but sound is not output
(2) Check following
Is the SPK cablenormal?
Is the SPK cableconnected well?
Cable inserts well.
No
No
Replace IC400
No
Replace IC401
No
Replace SPK cableYes
Yes
Is the RF/ AV/Component/ RGB/
HDMI sound normal?
No Does IC400Operates ?
Does IC401Operates ?
Replace IC402
No
Does IC402Operates ?
Replace VSC B/D
Yes Yes
-
- 23 -
BLOCK DIAGRAM
cabl
e
-
- 24 -
EXPLODED VIEW
300
301
540
121
601600
120
305
303
530
501541
410
580
200
400
203
204
201
205
207
206
202
302
304
430
401
520
-
- 25 -
120 6401VD0013G SPEAKER ASSEMBLY, FULL RANGE(R) RZ-42PX10
121 6401VD0013H SPEAKER ASSEMBLY, FULL RANGE(L) RZ-42PX10
200 6348Q-E080Q PDP, 42 852*480 PDP42V70002.AKLGG
201 6871QCH053A PWB(PCB) ASSEMBLY,DISPLAY CTRL ASSY HAND INSERT 42V7 FPGA
202 6871QDH084A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42V7 YDRV TOP B/D
203 6871QDH085A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42V7 YDRV BTM B/D
204 6871QLH047A PWB(PCB) ASSEMBLY,DISPLAY XRLT ASSY HAND INSERT 42V7 XL B/D
205 6871QRH055A PWB(PCB) ASSEMBLY,DISPLAY XRRT ASSY HAND INSERT 42V7 XR B/D
206 6871QYH036A PWB(PCB) ASSEMBLY,DISPLAY YSUS ASSY HAND INSERT 42V7
207 6871QZH041A PWB(PCB) ASSEMBLY,DISPLAY ZSUS ASSY HAND INSERT 42V7
300 3091V00645L CABINET ASSEMBLY, 42PX2RV-TA AF05FC
301 4980V01067D SUPPORTER, ASSY AL FILTER TOP DN-42PX12X 7T
302 4980V01068D SUPPORTER, ASSY AL FILTER BOT DN-42PX12X 7T
303 4980V01069D SUPPORTER, ASSY AL FILTER RIGHT DN-42PX12X 7T
304 4980V01070D SUPPORTER, ASSY AL FILTER LEFT DN-42PX12X 7T
305 5230V00019B FILTER(MECH), RT-42PX10 FG401PAA-05 LG CHEMICAL GLASS FILTER MECH
400 3809V00605A BACK COVER ASSEMBLY, CHASSIS CHANGE
3809V00605E BACK COVER ASSEMBLY, CHASSIS CHANGE WARNING LABEL LGEAP
401 3301V00085B PLATE ASSEMBLY, ASSY 3300V00552B RT-42PX17 PLATE TUNER COVER
410 4980V01071A SUPPORTER, ASSY AL MODULE VER. RZ-42PX10
430 3501V00216C BOARD ASSEMBLY, ASSY AP-42DX30 MF056C
501 3301V00083A PLATE ASSEMBLY, ASSY 3300V00550A 3301V00084A 42PX17/30 PLATE TUNER
520 6871VMMF21A PWB(PCB) ASSEMBLY,MAIN MF-056A H2, 42PX4RV-TA/42PX3RV-TA
6871VMMF60A PWB(PCB) ASSEMBLY,MAIN MF-056A H2, 42PX3RV-TA FOR AUSTRALIA
530 6871VSMS32A PWB(PCB) ASSEMBLY,SUB CONT MF056A RT-42PX17
540 6871VSME92A PWB(PCB) ASSEMBLY,SUB PSW RF043A MAILBU
541 5020V00915A BUTTON, POWER RZ-42PX20 ABS 1KEY
580 3501V00220A POWER SUPPLY ASSEMBLY, HURRICANE2 FREE VOLTAGE SANKEN 42 PSU
600 6871VSMS18B PWB(PCB) ASSEMBLY,SUB A/V MF056A RT/RZ-42PX40 SIDE A/V SUSAB
601 4811V00118B BRACKET ASSEMBLY, DECO RU-42PX10 RF043A SIDE AV
EXPLODED VIEW PARTS LISTNo. Part No. Descriptions
-
MIC39100 MICREL 3P SOT223 R/TPBA033FP-E2 ROHM 3P-SOP,TO252-3KA7809R, FAIRCHILD 2P D-PAK, R/TPSC156515M-1.8TR SEMTECH 5P/TO-263-5BA033FP-E2 ROHM 3P-SOP,TO252-3BA033FP-E2 ROHM 3P-SOP,TO252-3BA033FP-E2 ROHM 3P-SOP,TO252-3MIC39100 MICREL 3P SOT223 R/TPSC156515M-1.8TR 5P/TO-263-5 R/TPKIA78R05F KEC 5PIN DPAK R/TP 1A,5VSC156515M-1.8TR SEMTECH 5P/TO-263-5MIC39100 3P SOT223 R/TP LDO TYPE 2.5VBA033FP-E2 3P-SOP,TO252-3 R/TP 3.3VSII9011CLU(PB FREE) SILICON IMAGE 128PAT24C02N-10SI-2.7 ATMEL 8P SOIC R/TPMC34063ADR2G ON SEMI SO-8P R/TPCXA2069Q QFP64 BK I2C BUS AV S/WLA7217M MFP14 TP SYNC SEPARATORMSP4410K MICRONAS 80P/PQFPNSP-2100A,LF NEOFIDELITY TQFP 64P R/TPTAS5122DCARG4,LF 56P/TSSOP R/TP 30W74HC14D 14SOP TP SHITTER TRIGGERAT24C02N-10SI-2.7 ATMEL 8P SOIC74HC14D 14SOP TP SHITTER TRIGGERICL3232CBNZ INTERSIL 16P/SOPFLI8125BB-LF GENESIS 208P/PQFPAT24C32AN-10SI-2.7 ATMEL 8PIN SOPSST25VF040-20-4C-S2AE-T SST SOICFLI8532BD-LF GENESIS 416P/PBGA24LC256T-I/SMG(PB FREE) MICROSOFT WARE, 3.21V 8BEC PDP MF056AK4D261638F-LC50,LF TSOPII 66PK4D261638F-LC50,LF TSOPII 66PSOFT WARE, 3.19V F733 PDP MF056A
BSS83 TP PHILIPS N-CHANNEL S/W TRBSS83 TP PHILIPS N-CHANNEL S/W TRBSS83 TP PHILIPS N-CHANNEL S/W TRBSS83 TP PHILIPS N-CHANNEL S/W TRBSS83 TP PHILIPS N-CHANNEL S/W TRBSS83 TP PHILIPS N-CHANNEL S/W TRBSS83 TP PHILIPS N-CHANNEL S/W TRBSS83 TP PHILIPS N-CHANNEL S/W TR2SC3875S(ALY) BK KEC2SC3875S(ALY) BK KEC2SC3875S(ALY) BK KEC2SC3875S(ALY) BK KEC2SC3875S(ALY) BK KEC2SC3875S(ALY) BK KEC2SC3875S(ALY) BK KEC
REPLACEMENT PARTS LIST
LOCA. NO PART NO DESCRIPTION
Q101Q102Q102
Q1200Q200Q201Q202Q203Q204Q205Q207Q300Q301Q302Q303Q304Q305Q400Q401Q402Q403Q404Q405Q406Q407Q408Q409Q410Q411
D1005D1006D1007D1008D1009D1010D1012D1013D106D107D108D109D1100D1104D1105D1106D1107D1109D1110D1200D1201D200
0TR387500AA0TR102008AA0TR387500AA0TR387500AA0TR150400BA0TR387500AA0TR387500AA0TR150400BA0TR150400BA0TR387500AA0TR150400BA0TR387500AA0TR387500AA0TR387500AA0TR387500AA0TR387500AA0TR150400BA0TR387500AA0TR387500AA0TR387500AA0TR387500AA0TR387500AA0TR102008AA0TR102008AA0TR387500AA0TR102008AA0TR387500AA0TR387500AA0TR387500AA
0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD200009AF0DD200009AF0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DD184009AA0DS113379BA0DD184009AA
2SC3875S(ALY) BK KECKRA102S R/TP KEC SOT23 TR2SC3875S(ALY) BK KEC2SC3875S(ALY) BK KEC2SA1504S(ASY) BK KEC2SC3875S(ALY) BK KEC2SC3875S(ALY) BK KEC2SA1504S(ASY) BK KEC2SA1504S(ASY) BK KEC2SC3875S(ALY) BK KEC2SA1504S(ASY) BK KEC2SC3875S(ALY) BK KEC2SC3875S(ALY) BK KEC2SC3875S(ALY) BK KEC2SC3875S(ALY) BK KEC2SC3875S(ALY) BK KEC2SA1504S(ASY) BK KEC2SC3875S(ALY) BK KEC2SC3875S(ALY) BK KEC2SC3875S(ALY) BK KEC2SC3875S(ALY) BK KEC2SC3875S(ALY) BK KEC
KRA102S R/TP KEC SOT23 TRKRA102S R/TP KEC SOT23 TR2SC3875S(ALY) BK KEC
KRA102S R/TP KEC SOT23 TR2SC3875S(ALY) BK KEC2SC3875S(ALY) BK KEC2SC3875S(ALY) BK KEC
KDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECRU2M V(1) TP R-TMD 400V 1.1A 20A 0.4US 10UARU2M V(1) TP R-TMD 400V 1.1A 20A 0.4US 10UAKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECKDS184 TP KEC - 85V - 300MA1SS133 T-72 TP ROHM KOREA DO34 90VKDS184 TP KEC - 85V - 300MA
LOCA. NO PART NO DESCRIPTION
IC1000IC1001IC1002IC1003IC1004IC1005IC1100IC1101IC1102IC1103IC1104IC1105IC1106IC1200IC1201IC202IC300IC301IC400IC401IC402IC404IC500IC502IC600IC700IC701IC703IC800IC802IC900IC901IC902
S1
IC1202IC1203IC200IC201IC503IC504IC505IC506Q100Q1000Q1001Q1002Q1003Q1004Q101
0IPRPML001A0IMCRRH001A0IMCRFA010A0IPMG00027A0IMCRRH001A0IMCRRH001A0IMCRRH001A0IPRPML001A0IPMG00027A0IPMGKE030A0IPMG00027A0IPRPML001A0IMCRRH001A0IPRPS5005A0IMMRAL014B0IPMGON013B0ISO206900A0ISA721700C
0IMCRMN028B0ILNR00015A0IMCRTI028C0IPH741400E
0IMMRAL014B0IPH741400E0IPRP00009A0IMCR02006A0IMMRAL025A0IMMR00004A0IMCR02005A0IMMR00024A6927V1245AZ0IMMR00002A0IMMR00002A6927V1246AJ
0TR830009BA0TR830009BA0TR830009BA0TR830009BA0TR830009BA0TR830009BA0TR830009BA0TR830009BA0TR387500AA0TR387500AA0TR387500AA0TR387500AA0TR387500AA0TR387500AA0TR387500AA
IC
TRANSISTOR
- 26 -
DIODE
-
- 27 -
LOCA. NO PART NO DESCRIPTION
D300D500D501D502D503D504D505D506
ZD300ZD301ZD400ZD600
C1000C1005C1007C1009C1010C1019C1022C103C1030C1043C1046C1047C1050C1051C1064C1065C1066C1067C1068C1069C1071C1073C108C1082C1083C1084C1085C1087C1098C1099C1102C1105C1107C1108C1110C1115C1116C1117
0DD226239AA0DD226239AA0DD226239AA0DD226239AA0DR050008AA0DR050008AA0DR050008AA0DR050008AA0DR050008AA0DR050008AA0DZRM00248A0DR050008AA
0CE477SF6DC0CE477SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE476SF6DC0CE107SF6DC0CE4763F6180CE476SF6DC0CE476SF6DC0CE477SF6DC0CE476SF6DC0CE477SF6DC0CE477SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE477SF6DC0CE477SF6DC0CE227SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE477SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE107SF6DC0CE107SF6DC0CE477SF6DC0CE477DJ6180CE477SF6DC0CE227VF6DC
KDS226 TP KECKDS226 TP KECKDS226 TP KECKDS226 TP KECSD05.TC R/TP SEMTECH SOD323 5V 5A 15ASD05.TC R/TP SEMTECH SOD323 5V 5A 15ASD05.TC R/TP SEMTECH SOD323 5V 5A 15ASD05.TC R/TP SEMTECH SOD323 5V 5A 15ASD05.TC R/TP SEMTECH SOD323 5V 5A 15ASD05.TC R/TP SEMTECH SOD323 5V 5A 15ARLZ8.2B-TE11 ROHM R/TP LLDS(LL-34)SD05.TC R/TP SEMTECH SOD323 5V 5A 15A
470UF MVG 16V 20% R/TP(SMD) SMD470UF MVG 16V 20% R/TP(SMD) SMD100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP47UF SRE,SE 16V 20% FL TP 547UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP470UF MVG 16V 20% R/TP(SMD) SMD47UF MVG 16V 20% SMD R/TP470UF MVG 16V 20% R/TP(SMD) SMD470UF MVG 16V 20% R/TP(SMD) SMD47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP470UF MVG 16V 20% R/TP(SMD) SMD470UF MVG 16V 20% R/TP(SMD) SMD220UF MVG 16V 20% R/TP(SMD) SMD47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP470UF MVG 16V 20% R/TP(SMD) SMD47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP470UF MVG 16V 20% R/TP(SMD) SMD470UF STD 35V 20% FL TP 5470UF MVG 16V 20% R/TP(SMD) SMD220UF MV 16V 20% R/TP(SMD) SMD
LOCA. NO PART NO DESCRIPTION
C1118C1119C1120C1126C113
C1135C1136C1137C1138C114
C1148C1149C115
C1150C1151C1154C1159C1162C1165C1166C1185C1186C1187C1188C1189C1190C1191C1192C1193C1195C1199C1200C1201C1225C1230C1231C1245C1247C1302C1304C1306C1309C1311C1312C1313C1314C1315C1316C1317C1318C1405C1406
0CE477SF6DC0CE477DJ6180CE227VF6DC0CE477SF6DC0CE106SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE106SF6DC0CE476SF6DC0CE107SF6DC0CE227SF6DC0CE107SF6DC0CE107SF6DC0CE476SF6DC0CE476SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE106SF6DC0CE106SF6DC0CE106SF6DC0CK105DF64A0CK105DF64A0CE106SF6DC0CE476SF6DC0CE107SF6DC0CE476SF6DC0CE476SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE107SF6DC0CE476SF6DC0CE476SF6DC0CE476SF6DC0CE106SF6DC0CE106SF6DC
470UF MVG 16V 20% R/TP(SMD) SMD470UF STD 35V 20% FL TP 5220UF MV 16V 20% R/TP(SMD) SMD470UF MVG 16V 20% R/TP(SMD) SMD10UF MVG 16V 20% R/TP(SMD) SMD100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP10UF MVG 16V 20% R/TP(SMD) SMD47UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP220UF MVG 16V 20% R/TP(SMD) SMD100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP10UF MVG 16V 20% R/TP(SMD) SMD10UF MVG 16V 20% R/TP(SMD) SMD10UF MVG 16V 20% R/TP(SMD) SMD1UF 2012 16V 20% R/TP F(Y5V)1UF 2012 16V 20% R/TP F(Y5V)10UF MVG 16V 20% R/TP(SMD) SMD47UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP10UF MVG 16V 20% R/TP(SMD) SMD10UF MVG 16V 20% R/TP(SMD) SMD
CAPACITOR
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
-
- 28 -
LOCA. NO PART NO DESCRIPTION
C1410C1411C1414C1417C1417C1418C1418C1423C1424C1427C1428C1431C1432C1436C1437C1506C203C204C208C210C211C214C215C221C238C241C300C304C305C307C315C318C319C320C321C325C327C329C337C402C403C413C418C422C425C437C444C451C456C457C462C463
0CE106SF6DC0CK105DF64A0CE106SF6DC0CE475SK6DC0CE476SK6D80CE475SK6DC0CE476SK6D80CE106SH6DC0CE106SH6DC0CE227VF6DC0CE227VF6DC0CE106SH6DC0CE106SH6DC0CE227VF6DC0CE227VF6DC0CE476SF6DC0CE475SK6DC0CE477SF6DC0CE477SF6DC0CE475SK6DC0CE477SF6DC0CE106SF6DC0CE475SK6DC0CE477SF6DC0CE107SF6DC0CE476SK6D80CE107SF6DC0CE226SF6DC0CE107SF6DC0CE476SF6DC0CK225DFK4A0CK225DFK4A0CK225DFK4A0CK225DFK4A0CK225DFK4A0CK225DFK4A0CE476SF6DC0CE105SK6DC0CE105SK6DC0CE476SF6DC0CE226SF6DC0CE335VK6DC0CE107SF6DC0CE106SF6DC0CE226SF6DC0CE106SF6DC0CE107SF6DC0CK105DF64A0CK105DF64A0CE335VK6DC0CE107SF6DC0CE106SF6DC
10UF MVG 16V 20% R/TP(SMD) SMD1UF 2012 16V 20% R/TP F(Y5V)10UF MVG 16V 20% R/TP(SMD) SMD4.7UF MVG 50V 20% SMD R/TP47UF MVG,MC 50V 20% SMD TAPPING4.7UF MVG 50V 20% SMD R/TP47UF MVG,MC 50V 20% SMD TAPPING10UF MVG 25V 20% SMD R/TP10UF MVG 25V 20% SMD R/TP220UF MV 16V 20% R/TP(SMD) SMD220UF MV 16V 20% R/TP(SMD) SMD10UF MVG 25V 20% SMD R/TP10UF MVG 25V 20% SMD R/TP220UF MV 16V 20% R/TP(SMD) SMD220UF MV 16V 20% R/TP(SMD) SMD47UF MVG 16V 20% SMD R/TP4.7UF MVG 50V 20% SMD R/TP470UF MVG 16V 20% R/TP(SMD) SMD470UF MVG 16V 20% R/TP(SMD) SMD4.7UF MVG 50V 20% SMD R/TP470UF MVG 16V 20% R/TP(SMD) SMD10UF MVG 16V 20% R/TP(SMD) SMD4.7UF MVG 50V 20% SMD R/TP470UF MVG 16V 20% R/TP(SMD) SMD100UF MVG 16V 20% SMD R/TP47UF MVG,MC 50V 20% SMD TAPPING100UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP2.2UF 2012 16V 20%,-20% F(Y5V) R/TP2.2UF 2012 16V 20%,-20% F(Y5V) R/TP2.2UF 2012 16V 20%,-20% F(Y5V) R/TP2.2UF 2012 16V 20%,-20% F(Y5V) R/TP2.2UF 2012 16V 20%,-20% F(Y5V) R/TP2.2UF 2012 16V 20%,-20% F(Y5V) R/TP47UF MVG 16V 20% SMD R/TP1UF MVG 50V 20% SMD R/TP1UF MVG 50V 20% SMD R/TP47UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP3.3UF MV 50V 20% R/TP(SMD) SMD100UF MVG 16V 20% SMD R/TP10UF MVG 16V 20% R/TP(SMD) SMD22UF MVG 16V 20% SMD R/TP10UF MVG 16V 20% R/TP(SMD) SMD100UF MVG 16V 20% SMD R/TP1UF 2012 16V 20% R/TP F(Y5V)1UF 2012 16V 20% R/TP F(Y5V)3.3UF MV 50V 20% R/TP(SMD) SMD100UF MVG 16V 20% SMD R/TP10UF MVG 16V 20% R/TP(SMD) SMD
LOCA. NO PART NO DESCRIPTION
C464C465C480C481C482C483C484C495C527C610C728C729C730C731C735C737C739C745C750C752C760C762C764C767C771C832C833C834C835C836C837C838C839C840C851C853C884C896C901C904C905C930C943C950
L1000L1101L1102L1103L1104L1124
0CE106SF6DC0CE106SK6DC0CE108DJ6180CE475SK6DC0CE475SK6DC0CF4741L4380CF4741L4380CE108DJ6180CE476SF6DC0CE107SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC0CE226SF6DC
6140VB0004B6140VB0004B6140VB0004B6140VB0004B6140VB0004B6140VB0004B
10UF MVG 16V 20% R/TP(SMD) SMD10UF MVG 50V 20% SMD R/TP1000UF STD 35V M FL TP54.7UF MVG 50V 20% SMD R/TP4.7UF MVG 50V 20% SMD R/TP0.47UF D 63V 5% TP 5 M/PE NI0.47UF D 63V 5% TP 5 M/PE NI1000UF STD 35V M FL TP547UF MVG 16V 20% SMD R/TP100UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP22UF MVG 16V 20% SMD R/TP
26UH 1UEWPHY 22.5TURN YL-9N 0.426UH 1UEWPHY 22.5TURN YL-9N 0.426UH 1UEWPHY 22.5TURN YL-9N 0.426UH 1UEWPHY 22.5TURN YL-9N 0.426UH 1UEWPHY 22.5TURN YL-9N 0.426UH 1UEWPHY 22.5TURN YL-9N 0.4
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
COIL
-
- 29 -
LOCA. NO PART NO DESCRIPTION
L404L405L406L407
C1C2C3C4C5C6C7C8C9
JK500JK601
AR1200AR1201AR1202AR1203AR1204AR1205AR700AR701AR702AR703AR704AR705AR806AR806AR807AR807AR808AR808AR809AR809AR810AR810AR811AR811AR812AR812AR813AR813AR814AR814AR815AR815AR816
6140VB0032A6140VB0032A6140VB0032A6140VB0032A
387-J12N6631V00020F6631V00045B6631V12047L6631V25083A6631V39013N6631V39021H6631V39022D6631V39023D6630G70016A6630G70017A
0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001D0RRZVTA001B0RRZVTA001D0RRZVTA001B0RRZVTA001D0RRZVTA001B0RRZVTA001D0RRZVTA001B0RRZVTA001D0RRZVTA001B0RRZVTA001D0RRZVTA001B0RRZVTA001D0RRZVTA001B0RRZVTA001D0RRZVTA001B0RRZVTA001D0RRZVTA001B0RRZVTA001D0RRZVTA001B0RRZVTA001D0RRZVTA001B
DBF-1015A 15.5UH 10PIE DIGITAL AUDIODBF-1015A 15.5UH 10PIE DIGITAL AUDIODBF-1015A 15.5UH 10PIE DIGITAL AUDIODBF-1015A 15.5UH 10PIE DIGITAL AUDIO
12P 2.5MM 900MM H-H UL1185AWG263P 3.96MM 250MM H-W UL1672 AWG1810P SPECIAL 150MM H-H UL1007AWG2413P 1.25MM 700MM H-H UL1061AWG287P 2.5MM 100MM H-H UL1007 AWG248P 3.96MM 900MM H-H UL1617AWG224P 3.96MM 450MM H-H UL1672AWG184P 3.96MM 250MM H-H UL1007AWG1810P 3.96MM 250MM H-H UL1007AWG18A03-7071-094 SPG 15P 2.29MMA02-0915-101 SPG 9P 2.54MM
22 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E2422 OHM 1 / 16 W 1608 5% R/TP 4P E24MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E24MNR14-E0A-J-510 R OHM 51 OHM 5%
LOCA. NO PART NO DESCRIPTION
AR816AR817AR817R230R801R802
D1003D1101D1102D1103D1104LD101
SW101SW102SW103SW104SW105SW106SW107SW108SW700SW800SW800
L100L1004L1005L1006L1007L1008L1009L101
L1010L1011L1012L1013L1014L1015L1016L1017L1018L1019L102
L1020L1021L1022L1023
0RRZVTA001D0RRZVTA001B0RRZVTA001D0RD0331H6090RKZVTA001L0RKZVTA001L
0DL233309AC0DL233309AC0DL233309AC0DL233309AC0DL233309AC0DL200000CA
140-315A140-315A140-315A140-315A140-315A140-315A140-315A140-315A
6600VR1004A6600VM2006A6600VR1004A
6200JB8010L6200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200JB8010L6200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200JB8010L6200J0000136200J0000136200J0000136200J000013
22 OHM 1 / 16 W 1608 5% R/TP 4P E24MNR14-E0A-J-510 R OHM 51 OHM 5% 22 OHM 1 / 16 W 1608 5% R/TP 4P E243.3 OHM 1/2 W 5.00% TA521.0M OHM 1/2 W 5% TA52 UL PILKOR1.0M OHM 1/2 W 5% TA52 UL PILKOR
SAM2333 GREEN:10MCD, RED:6MCDSAM2333 GREEN:10MCD, RED:6MCDSAM2333 GREEN:10MCD, RED:6MCDSAM2333 GREEN:10MCD, RED:6MCDSAM2333 GREEN:10MCD, RED:6MCDSAM5670(DL-2LRG) BK Y-GREEN
SKHV17910B 12V 0.05A HORIZONTAL 160GSKHV17910B 12V 0.05A HORIZONTAL 160GSKHV17910B 12V 0.05A HORIZONTAL 160GSKHV17910B 12V 0.05A HORIZONTAL 160GSKHV17910B 12V 0.05A HORIZONTAL 160GSKHV17910B 12V 0.05A HORIZONTAL 160GSKHV17910B 12V 0.05A HORIZONTAL 160GSKHV17910B 12V 0.05A HORIZONTAL 160GSKHMPW 5P J-ALPS .V .A HORIZONTAL .GSDDF3PATP011 250V 4A HORIZONTAL .GSKHMPW 5P J-ALPS .V .A HORIZONTAL .G
MLB-201209-1000L-N2 R/TP 1000OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-201209-1000L-N2 R/TP 1000OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-201209-1000L-N2 R/TP 1000OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHM
SWITCH
FILTER & CRYSTAL
LED
RESISTOR
CONNECTOR
For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;
CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic
RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible
-
- 30 -
LOCA. NO PART NO DESCRIPTION
L1024L1025L103L109L110L1105L1106L1107L1108L1109L111L1110L1111L1112L1113L1115L1116L1117L1118L1119L1120L1121L1122L1123L1125L1126L1127L1128L1129L1130L1204L1205L1206L1207L1208L1209L200L201L202L203L204L300L301L302L400L401L402L403L408L409L414L415
6200J0000136200J0000136200JB8010L6200JB8010L6200JB8010L6200J0000136200J0000136200J0000136200J0000136200J0000136200JB8010L6200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200J0000136200JB8010L6200J0000136200J0000136200J0000136200J0000136200JB8010L6200JB8010L6200J0000136200J000013
MLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-201209-1000L-N2 R/TP 1000OHMMLB-201209-1000L-N2 R/TP 1000OHMMLB-201209-1000L-N2 R/TP 1000OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-201209-1000L-N2 R/TP 1000OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-201209-1000L-N2 R/TP 1000OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-201209-1000L-N2 R/TP 1000OHMMLB-201209-1000L-N2 R/TP 1000OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHM
LOCA. NO PART NO DESCRIPTION
L416L417L500L502L503L506L604L900
X1200X300X400X700X800
JK100JK101JK101JK102
JK1200JK400JK502JK600
A1A2A3A4
C10C11C12F801
PA101TU200TU201
6200J0000136200J0000136200J0000136200JB8010L6200JB8010L6200J0000136200J0000136200J0000136212AB2845A
166-E02F156-A02M
6212AB2844A6212AB2844A
6612J00040B6612J10012A6613V00026A6612J10012A6612B00015B6612J00037A6612F00087A6612F00087A
3828VA0545A6710V00138P6410VEH003K4972V00178A
6850J00005B6850VA0004J6851V00022C0FS1002B53K6712000002B6700MF0010B6700MF0010A
MLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-201209-1000L-N2 R/TP 1000OHMMLB-201209-1000L-N2 R/TP 1000OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMMLB-321611-0500P-N2 R/TP 500 OHMRESONATOR,CRYSTAL ABLS-27.000MHZRESONATOR,CERAMIC CSBLA500KECZF09RESONATOR,CRYSTAL HC49U 18.432MHZRESONATOR,CRYSTAL ABLS-19.6608MHZRESONATOR,CRYSTAL ABLS-19.6608MHZ
UJB-06-23B UGCOM 6P RCA+1P S-JACKUJB-05-02C UGCOM COMPONENTUJB-03-28A 6613V00004S+SHIEL+SCREWUJB-05-02C UGCOM COMPONENTDC1R019WDH JAE 0.5MM,19PIN+2PIN,HDMI S/TUJB-02-12A UGCOM 2P RCA VERTICAL+SHIELDUEJ-CV-032 UGCOM EAR JACK 10MM UEJ-CV-032 UGCOM EAR JACK 10MM
MANUAL, USER MF056A EN 138P TXREMOTE CONTROLLER, MF056A POWER CORD, 003C-G/SOURCING WITH PACKINGFIXER, WALL ASSY PDP SET
CABLE,DVILVDS UL20276 AWG30 500MMCABLE,COAXIALUL1365#26 150MMCABLE,COAXIALUL1365#26 VW-1FUSE,SLOW BLOW 10000MA 250 V 5.2X20REMOTE CONTROLLER RECEIVER,KSM-603SM12E-1TUNER,TAFM-W502P 4SYSTEM SUBTUNER,TAUM-W501P 4 SYSTEM MAIN
ACCESSORIES
MISCELLANEOUS
JACK
-
PRINTED CIRCUIT BOARDMAIN (TOP) MAIN (BOTTOM )
SIDE A/V(TOP)
CONTROL(TOP)
SIDE A/V(BOTTOM)
POWER SWITCH(TOP)
CONTROL(BOTTOM)
POWER SWITCH(BOTTOM)
-
Jun., 2005Printed in KoreaP/NO : 3828VD0209V
#EV#