sharp xl 1200 stereo user manual

8/10/2019 Sharp XL 1200 Stereo User Manual

http://slidepdf.com/reader/full/sharp-xl-1200-stereo-user-manual 1/32

Thank you for purchasing this SHARP product.To obtain the best performance from this product, pleaseread this manual carefully. It will guide you in operatingyour SHARP product.

XL-1200 Compact Audio System consisting of XL-1200 (mainunit) and CP-XL1200U (speaker system).

COMPACT AUDIO SYSTEM

MODEL

XL-1200OPERATION MANUAL

XL1200(FRONT) 01.2.19, 7:01 PM1



01/2/19 XL-1200(U)1.fm

6

G e n e r a

l I n f o r m a t i o n

- P r e c a u t i o

n s

/ A c c e s s o r i e s -

Precautions (continued)„ Care of compact discsCompact discs are fairly resistant to damage, however mistrackingcan occur due to an accumulation of dirt on the disc surface. Followthe guidelines below for maximum enjoyment from your CD collec-tion and player.z Do not write on either side of the disc, particularly the non-label

side from which signals are read. Do not mark this surface.z Keep your discs away from direct sunlight, heat, and excessive

moisture.z Always hold the CDs by the edges. Fingerprints, dirt, or water on

the CDs can cause noise or mistracking. If a CD is dirty or doesnot play properly, clean it with a soft, dry cloth, wiping straight outfrom the center, along the radius.

„ Condensation

AccessoriesPlease confirm that the following accessories are included.

Note:Only the above accessories are included.

Sudden temperature changes, storageor operation in an extremely humid en-vironment may cause condensation in-side the cabinet (CD pickup, etc.) or onthe transmitter on the remote control.Condensation can cause the unit to

malfunction. If this happens, leave thepower on with no disc in the unit untilnormal playback is possible (about 1hour). Wipe off any condensation onthe transmitter with a soft cloth beforeoperating the unit.

NO YEScorrect

AC power cord 1 Remote control 1(QACCD0001SJ00) (RRMCG0032SJSA)

AM loop antenna 1 FM antenna 1(QANTL0001SJZZ) (QANTW0002SJZZ)

Speaker wire 2(QCNWH0006SJZZ)



01/2/19 XL-1200(U)1.fm

7

G e n e r a


- C o n

t r o l s a n

d I n d i c a t o r s -

Controls and Indicators„ Front panel

Reference page1. CD Compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 182. Volume Up and Down Buttons . . . . . . . . . . . . . . . . . . . . . . 163. Power Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154. Function Selector Button . . . . . . . . . . . . . . . . . . . . . 18, 22, 285. Memory/Set Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21, 246. Bass/Treble Selector Button . . . . . . . . . . . . . . . . . . . . . . . . 167. CD Play or Pause, Tuning Up Button . . . . . . . . . . . 18, 19, 228. CD Stop, Tuning Down Button . . . . . . . . . . . . . . . . . . . 19, 229. CD Track Down or Fast Reverse,

Tuner Preset Down Button . . . . . . . . . . . . . . . . . . . . . . 20, 2410. CD Open/Close Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1511. CD Track Up or Fast Forward,

Tuner Prese t Up Button . . . . . . . . . . . . . . . . . . . . . . . . . 20, 24

„ Display1. Timer Play Indicator2. Sleep Indicator3. CD Random Play Indicator4. Memory Indicator5. FM Stereo Mode Indicator6. CD Play Indicator7. CD Repeat Play Indicator8. FM Stereo Receiving Indicator

1

2

3

4

5

6

7

8

9

10

11

1 2 3 4 5

7

6

8

Description of remote control (See page 9.)



01/2/19 XL-1200(U)1.fm

8

G e n e r a


- C o n

t r o l s a n


Controls and Indicators (continued)„ Rear panel

Reference page1. Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282. AM Antenna Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 133. Antenna Earth Terminal . . . . . . . . . . . . . . . . . . . . . . . . . 12, 134. FM 75 Ohms Antenna Jack . . . . . . . . . . . . . . . . . . . . . . 12, 135. CD Digital Output Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286. Subwoofer Output Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147. Video/Auxiliary (Audio Signal) Input Jacks . . . . . . . . . . . . 288. Speaker Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 149. AC Power Input Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 14

5

6

7

8

9

2

1

3

4



01/2/19 XL-1200(U)1.fm

10

G e n e r a


- C o n

t r o l s a n


Controls and Indicators (continued)

„ Speaker system

1. Tweeter2. Woofer

3. Bass Reflex Duct4. Speaker Terminals

Placing the speaker system:There is no distinction between the right and the left speakers.

4

32

1

Speaker grilles are removable:Make sure nothing comes into contact withthe speaker diaphragms when you removethe speaker grilles.

Left speaker Right speaker

Notes:z The speakers are magnetically shielded.

Therefore, they do not affect the display even if you use them nearthe TV. However, some color variation may occur, depending onthe type of TV used.

If color variation occurs...Turn off the TV (from the power switch).After 15 - 30 minutes, turn the TV on again.

If the color variation is still present...Move the speakers further away from the TV.

z If any kind of magnet or an electromagnet is placed too close to

the TV and the system, irregular colors may appear on the TVscreen.



01/2/19 XL-1200(U)2.fm

11

P r e p a r a t i o n

f o r

U s e

- R e m

o t e C o n

t r o l -

Remote Control„ Battery installation

Precautions for battery use:z Replace all old batteries with new ones at the same time.z Do not mix old and new batteries.z Remove the batteries if the unit will not be used for long periods

of time. This will prevent potential damage due to battery leak-age.

Caution:z Do not use rechargeable batteries (nickel-cadmium battery, etc.).z Installing the batteries incorrectly may cause the unit to malfunc-

tion.

Notes concerning use:z Replace the batteries if the operating distance is reduced or if the

operation becomes erratic.z Periodically clean the transmitter on the remote control and thesensor on the unit with a soft c loth.

z Exposing the sensor on the unit to strong light may interfere withoperation. Change the lighting or the direction of the unit.

z Keep the remote control away from moisture, heat, shock, andvibrations.

„ Test of the remote controlCheck the remote control after checking all connections have beenmade correctly. (See pages 12 - 14.)Face the remote control directly to the remote sensor on the unit.

The remote control can be used within the range shown below:Press the POWER button. Does the power turn on? Now, you canenjoy the music.

Use 2 "AAA" size batteries (UM-4, R03, HP-16 or similar).Batteries are not included.

1 Remove the battery cover.2 Insert the batteries according to the direction indicated in

the battery compartment. When inserting or removing the batteries, push them toward the

battery terminals.3 Replace the cover.

Remote sensor

8" - 20'(0.2 m - 6 m )



01/2/19 XL-1200(U)2.fm

12

P r e p a r a t i o n

f o r

U s e

- S y s t e m

C o n n e c t i o n s -

System Connections

VCR, DVD, etc.

Speaker with abuilt-in amplifier

Right speaker Left speaker

FM antenna

AM loop antenna

AC outlet(AC 120 V, 60 Hz)

not supplied

(This speaker is not included.)

MD recorder

not supplied

not supplied



01/2/19 XL-1200(U)2.fm

15

B a s i c

O p e r a t i o n

- G e n e r a l C o n

t r o l -

General Control„ To turn the power onPress the POWER button to turn the power on.

To set the unit to stand-by mode:Press the POWER button again.

„ To change the display brightness (2 levels)You can switch the display brightness by pressing the DIMMER but-ton on the remote control.

„ Opening and closing the CD compartmentThe CD compartment cover is motorized.

When the power is turned on, you can open or close the CD com-partment cover by pressing the (OPEN/CLOSE) button.

Caution:z Do not open or close the CD compar tment cover manually. It may

cause malfunctions to the unit.z Be careful not to jam your fingers in the CD compartment cover.

Dimmed Brightened



01/2/19 XL-1200(U)2.fm

16

B a s i c

O p e r a t i o n

- S o u n

d C o n

t r o l -

Sound Control„ Adjusting the volumePress the VOLUME button to increase the volume and the VOL-UME button for decreasing.

„ Adjusting the bassMain unit operation:1 Press the BASS/TREBLE button until "BASS" appears on the

display.2 Within 5 seconds, press the VOLUME ( or ) button to adjust

the bass.

Remote control operation:Press the BASS ( or ) button to adjust the bass.

„ Adjusting the trebleMain unit operation:1 Press the BASS/TREBLE button until "TRE" appears on the dis-

play.2 Within 5 seconds, press the VOLUME ( or ) button to adjust

the treble.

Remote control operation:Press the TREBLE ( or ) button to adjust the treble.

21 28 29 MAXMIN .....

0 5-5 ... ...

0 5-5 ... ...



01/2/19 XL-1200(U)2.fm

17

B a s i c

O p e r a t i o n

- S e t t i n g

t h e

C l o c k -

Setting the Clock

This may be operated only with the remote control.In this example, the clock is set for the 12-hour (AM 12:00) display.

To confirm the t ime display when the power is on:Press the CLOCK button.The time display will appear for about 5 seconds.

Note:The time will flash at the push of the CLOCK button when the ACpower supply is restored after a power failure or unplugging the unit.Readjust the clock as follows.

To readjust the clock:Perform "Setting the Clock" from the beginning.

To change the 12-hour or 24-hour display:

1 Press the CLOCK button and within 3 seconds, pressthe MEMORY button.

2 Within 1 minute, press the PRESET ( or ) button toselect 12-hour or 24-hour display and then press theMEMORY button.

"AM 12:00" The 12-hour display will appear. (AM 12:00 - PM 11:59)"0:00" The 24-hour display will appear. (0:00 - 23:59)Note that this can only be set when the unit is first installed or ithas been reset. (Refer to step 3 under "If trouble occurs" onpage 30.)

3 Within 1 minute, press the PRESET ( or ) button toadjust the hour and then press the MEMORY button.

z When the 12-hour display is selected, "AM" will change au-

tomatically to "PM".4 Within 1 minute, press the PRESET ( or ) button to

adjust the minutes and then press the MEMORY button.

z The hour will not advance even if minutes advance from "59"to "00".

z The clock starts from "0" second. (Seconds are not dis-played.)

1 Clear all the programmed contents. [Perform to step 3 under "Iftrouble occurs" on page 30 for details.]

2 Perform "Setting the Clock" from the beginning.



01/2/19 XL-1200(U)2.fm

18

C D

P l a y b a c k

- L i s t e n

i n g

t o a

C D -

Listening to a CD1 Press the POWER button to turn the power on.

2 Press the FUNCTION button until "CD STOP" or "NODISC" appears on the display.When operating with the remote control, press the CD button.

3 Press the (OPEN/CLOSE) button to open the CD com-

partment.4 Place a CD on the spindle, label side up.

Be sure to place 3" (8 cm) disc in the middle of a disc holder.

5 Press the (OPEN/CLOSE) button toclose the CD com-partment.

Total number oftracks

Total playing time

6 Press the ( ) button to start playback from track 1.

When the last track on the disc has finished playing, the CDplayer will stop automatically.

5" (12 cm)3" (8 cm)

Sound Control (See page 16.)



01/2/19 XL-1200(U)2.fm

19

C D

P l a y b a c k

- L i s t e n

i n g

t o a

C D -

To interrupt playback:Main unit operation:Press the button.To resume playback from the same point, press the button again.Remote control operation:Press the button.To resume playback from the same point, press the button.

To stop playback:Press the button.

To remove the CD:While in the stop mode, press the (OPEN/CLOSE) button.Press the CD ejec t button and remove the CD.

Notes:z After removing the CD, make sure to press the (OPEN/CLOSE)

button and close the CD compartment.z When the unit enters the stand-by mode, the opened CD com-

partment cover will be closed automatically.

After use:Press the POWER button to enter the power stand-by mode.

Caution:z Do not open or close the CD compartment cover manually. It

may cause malfunctions to the unit.z Be careful not to jam your fingers in the CD compartment

cover.z If the power fails while the compartment is open, wait until the

power is restored.z If a disc is damaged, dirty, or loaded upside down, "NO DISC" or

"READ ERR" will appear on the display.z Keep foreign objects out of the CD compartment.z Subjecting the unit to shock or vibration may cause mistracking.z When the unit is not being used, be sure to close the CD com-

partment. If it is left open, the lens may be covered with dust andthe unit may not operate properly.

z If TV or radio interference occurs during CD operation, move theunit away from the TV or radio.

CD Eject Button



01/2/19 XL-1200(U)2.fm

20

C D

P l a y b a c k

- L i s t e n i n g

t o a

C D / R e p e a t o r

R a n

d o m

P l a y -

Listening to a CD (continued)„ To locate the beginning of a track

„ To locate the desired portion

Notes:z Normal playback will resume when the or button is

released.z When the end of the last track is reached during fast forward,

"END" will appear on the display and CD operation will bepaused. When the beginning of the first track is reached duringfast reverse, playback will start when you release the button.

z The or button on the remote control allows you to locatethe desired portion.

Repeat or Random PlayYou can select one of the CD playback mode; "Repeat play", "Ran-dom play" and "Normal play".

To repeat a programmed sequence:Perform steps 1 - 5 in the "Programmed Play" section and thenselect the repeat playback.

Notes:z In random play, the CD player will select and play tracks automat-

ically. (You cannot select the order of the tracks.)z If you press the button during random play, you can move to

the track selected next by the random operation. On the otherhand, the button does not allow you to move to the previoustrack. The beginning of the track being played will be located.

Caution:After performing repeat or random play, be sure to press the but-ton. Otherwise, the disc will play continuously.

To cancel repeat or random play:Press the RANDOM/REPEAT button on the remote control repeat-edly to select the normal playback mode.

To move to the beginning of the next track:Press the button for less than 0.5 seconds during playback.

z You can skip to any track by pressing thebutton repeatedly until the desired tracknumber appears.

To restart the track being played:Press the button for less than 0.5 seconds during playback.

z You can skip to any track by pressing thebutton repeatedly until the desired tracknumber appears.

For audible fast forward:Press and hold down the button during playback.For audible fast reverse:Press and hold down the button during playback.

1 When in the CD mode, press the RANDOM/REPEATbutton on the remote control repeatedly to select theplayback mode.

Repeat playback mode Random playback mode

Normal playback mode

2 Press the button to start playback.



01/2/19 XL-1200(U)3.fm

21

C D

P l a y b a c k

- P r o g r a m m e d

P l a y -

Programmed PlayBy specifying tracks from 1 to 99, you can choose up to 20 selec-tions for playback in the order you like.

To cancel the programmed play mode:While in the stop mode and the "MEMORY" indicator is lit, press theCLEAR button on the remote control. The "MEMORY" indicator willdisappear and all the programmed contents will be cleared.

Adding tracks to the program:If a program has been previously stored, the "MEMORY" indicatorwill be displayed. Then follow steps 1 - 3 to add tracks. The newtracks will be stored after the last track of the original program.

Notes:z Opening the CD compartment automatically cancels the pro-

grammed sequence.z Even if you press the POWER button to enter the stand-by mode

or the function is changed from CD to some other function, theprogrammed selections will not be cleared.

z During program operation, random play is not possible.

1 While in the stop mode, press the MEMORY/SET (MEM-ORY) button to enter the programming save mode.

2 Within 30 seconds, press the or button to selectthe desired track.

Selected track number Playback time

3 Press the MEMORY/SET (MEMORY) button to save thetrack number.

Playback order Total playback time

4 Repeat steps 2 - 3 for other tracks. Up to 20 tracks canbe programmed.

5 Press the ( ) button to start playback.

To clear the programmed selec-tions:Press the CLEAR button on the remotecontrol while the "MEMORY" indicatoris flashing.Each time the button is pressed, onetrack will be cleared, beginning with thelast track programmed.



01/2/19 XL-1200(U)3.fm

22

R a d

i o

- L i s t e n i n g

t o t h e

R a d

i o -

Listening to the Radio1 Press the POWER button to turn the power on.

2 Press the FUNCTION button until "FM" or "AM" ap-pears on the display.When operating with the remote control, press the TUNER but-ton, and then the BAND button to select "FM" or "AM".

3 Press the TUNING ( or ) button to tune in to the de-sired station.Manual tuning:Press the TUNING button as many times as required to tune into the desired station.Auto tuning:When the TUNING button is pressed for more than 0.5 sec-onds, scanning will start automatically and the tuner will stop atthe first receivable broadcast station.

Notes:z This can be operated by pressing the TUN. ( or ) button

on the remote control.z When radio interference occurs, auto scan tuning may stop

automatically at that point.z Auto scan tuning will skip weak signal stations.z To stop the auto tuning, press the TUNING button again.

Sound Control (See page 16.)



01/2/19 XL-1200(U)3.fm

23

R a d

i o

- L i s t e n i n g

t o t h e

R a d

i o -

To receive an FM stereo transmission:Press the FUNCTION (BAND) button to display the "ST" indicator.z " " will appear when an FM broadcast is in stereo.

z If the FM reception is weak, press the FUNCTION (BAND) button

to extinguish the "ST" indicator. The reception changes to mon-aural, and the sound becomes clearer.

After use:Press the POWER button to enter the power stand-by mode.

FM stereo mode indicator

FM stereo receiving indicator



01/2/19 XL-1200(U)3.fm

24

R a d

i o

- L i s t e n i n g

t o t h e

M e m o r i z e d

S t a t i o n -

Listening to the Memorized Station„ Memorizing a stationYou can store 30 AM and FM stations in memory and recall them atthe push of a button. (Preset tuning)

Note:The backup function protects the memorized stations for a few hoursshould there be a power failure or the AC power cord disconnection.

„ To recall a memorized station

„ To scan the preset stationsThe stations saved in memory can be scanned automatically. (Pre-set memory scan)

„ To clear a memorized station

1 Perform the steps 1 - 3 in "Listening to the Radio" onpage 22.

2 Press the MEMORY/SET

(MEMORY) button to enter thepreset tuning saving mode.

3 Within 5 seconds, press thePRESET ( or ) button to se-lect the preset channel num-ber.Store the stations in memory, in order, starting with presetchannel 1.

4 Within 5 seconds, press theMEMORY/SET (MEMORY) but-ton to store that station inmemory.If the "MEMORY" and preset number indicators go out beforethe station is memorized, repeat the operation from step 2.

5 Repeat steps 1 - 4 to set other stations, or to change apreset station.When a new station is stored in memory, the station previouslymemorized will be erased.

Press the PRESET ( or ) button for less than 0.5 seconds toselect the desired station.

Preset channel Frequency and frequency band

1 Press the PRESET ( or ) button for more than 0.5seconds.The preset number will flash and the programmed stations will

be tuned in sequentially, for 5 seconds each.2 Press the PRESET ( or ) button again when the de-

sired station is located.

1 Recall the memorized station.2 While it is displayed, press the

MEMORY/SET (MEMORY) but-ton.

3 Within 5 seconds, press theCLEAR button on the remote con-trol.

Listening to the Radio (See page 22.)



01/2/19 XL-1200(U)3.fm

25

A d v a n c e d

F e a t u r e s

- T i m e r a n

d S l e e p O p e r a t i o n -

Timer and Sleep OperationThis may be operated only with the remote control.

Timer playback:The unit turns on and plays the desired source (CD, tuner) at thepreset time.

Sleep operation:The radio and compact disc can all be turned off automatically.

„ Timer playbackBefore setting timer:

Continued to the next page

1 Press the CLOCK button to check that the clock is on time.

2 Load a disc to be played.

1 Press the POWER button to turn the power on.

2 Press the CD or TUNER button to select the desiredfunction.When you selected the TUNER, tune in to the desired sta-tion.

3 Adjust the volume using the VOLUME buttons.

Do not turn the volume up too high.

4 Press the TIMER button and within 6 seconds, pressthe MEMORY button.

5 Within 1 minute, press the PRESET ( or ) button tospecify the hour to start, then press the MEMORY but-ton.

Setting the Clock (See page 17.) / Listening to the Radio (See page 22.)



01/2/19 XL-1200(U)3.fm

26

A d v a n c e d

F e a t u r e s

- T i m e r a n


Timer and Sleep Operation (continued)

To reset or change the timer setting:Perform "Timer playback" from the beginning.

Notes:z Once the time is set, the setting will be retained until a new time

is entered.z When performing timer playback using another unit connected to

the VIDEO/AUX IN jacks, select "VIDEO/AUX" in step 2. At thistime, only this unit will be turned on or enter the power stand-bymode automatically. It will enter the power stand-by mode 1 hourafter the timer playback starts. (Another unit will not be turned onor off.)

6 Within 1 minute, press the PRESET ( or ) button tospecify the minutes to start, then press the MEMORYbutton.z The timer playback starting time, function, and volume will be

displayed, and then the unit will enter the stand-by mode au-tomatically.

z " " will appear and the current time will be displayed.

To cancel the timer playback:Press the POWER button to turn the power on.

7 When the preset time is reached, playback will start.

The volume will increase gradually until it reaches the volumeyou were listening at before your system enters the timer stand-by mode.

8 If you select CD, the unit will enter the stand-by modeafter the playback. If you select TUNER, it will enter thestand-by mode one hour after the timer playback starts.



01/2/19 XL-1200(U)3.fm

27

A d v a n c e d

F e a t u r e s

- T i m e r a n


„ Sleep operation

To cancel the sleep operation:Press the POWER button while the sleep timer is set.

To confirm the remaining sleep time:Press the SLEEP button once while the sleep timer is set.The remaining sleep time is displayed for about 3 seconds.

„ To use timer and sleep operation togetherExample: To fall asleep and wake to the same radio stationYou can play back the same source only (the function cannot beswitched).

1 Play back the desired sound source.

2 Press the SLEEP button.

To change the sleep time:Press the SLEEP button repeatedly to select the desired sleeptime. The time will decrease as follows.The amount of sleep time can also be changed while in thesleep mode.

3 Your system will enter the power stand-by mode auto-matically after the preset time has elapsed.The volume will be turned down 1 minute before the sleep op-eration finishes.

3:00 2:00

OFF 15 30

1:30 1:00

1 Set the sleep time (see left, steps 1 - 2).

2 While the sleep timer is set, set the desired playbacktime (steps 4 - 6, pages 25 - 26).

1.Sleep timer setting2.Timer playback setting

Timer playbackstart time

15 minutes - 3 hours Desired time

Sleep operation willautomatically stop.

End time



01/2/19 XL-1200(U)3.fm

29

R e f e r e n c e s

- T r o u b

l e s h o o

t i n g

C h a r t -

Troubleshooting ChartMany potential "problems" can be resolved by the owner withoutcalling a service technician.If something is wrong with this product, check the following beforecalling your authorized SHARP dealer or service center.

„ General

„ CD player

„ Tuner

„ Remote control

Symptom Possible causez The clock is not on

time.z Did a power failure occur? Reset the

clock. (Refer to page 17.)z When a button is

pressed, the unitdoes not respond.

z Set this unit to the power stand-bymode and then turn it back on.

z If the unit still malfunctions, reset it.(Refer to step 3 under "If trouble oc-curs" on page 30.)

z No sound is heard. z Is the volume level set to "0"?z Are the headphones connected?z Are the speaker wires disconnected?

Symptom Possible causez Playback does not

start.z Is the disc loaded upside down?

z Playback stops in themiddle or is not per-formed properly.

z Does the disc satisfy the standards?z Is the disc distorted or scratched?

z Playback sounds areskipped, or stoppedin the middle of atrack.

z Is the unit located near excessive vi-brations?

z Is the disc very dirty?z Has condensation formed inside the

unit?

Symptom Possible causez Radio makes unusual

noise consecutively.z Is the unit placed near the TV or com-

puter?z Is the FM antenna or AM loop anten-

na placed properly? Move the ACpower cord away from the antenna if

located near.

Symptom Possible causez The remote control

does not operate.z Is the AC power cord of the unit

plugged in?z Is the battery polarity respected?z Are the batteries dead?z Is the distance or angle incorrect?z Does the remote control sensor re-

ceive strong light?



01/2/19 XL-1200(U)3.fm

30

R e f e r e n c e s

- T r o u

b l e s h o o

t i n g

C h a r t

/ M a i n

t e n a n c e -

Troubleshooting Chart (continued)„ If trouble occursWhen this product is subjected to strong external interference(mechanical shock, excessive static electricity, abnormal supplyvoltage due to lightning, etc.) or if it is operated incorrectly, it maymalfunction.

If such a problem occurs, do the following:

Caution:This operation will erase all data stored in memory including clock,timer settings, tuner preset, and CD program.

Maintenance„ Cleaning the CD pickup lensDo not touch the laser pickup lens. If fingerprints or dust accumulateon the pickup, clean it gently with a dry cotton swab.

„ Cleaning the cabinet

1 Set the unit to the stand-by mode and turn the power onagain.2 If the unit is not restored in step 1, unplug and plug in theunit, and then turn the power on.

3 If neither step 1 nor 2 restores the unit, do the following:Press the POWER button to enter the power stand-by mode.Unplug the AC power cord from the AC INPUT jack on theunit.While pressing down the MEMORY/SET button and thebutton, plug the AC power cord into the AC INPUT jack on theunit.

AC INPUT

Periodically wipe the cabinet with a soft clothand a diluted soap solution, then with a drycloth. Caution:z Do not use chemicals for cleaning (gaso-

line, paint thinner, etc.). It may damagethe cabinet finish.

z Do not apply oil to the inside of the unit. Itmay cause malfunctions.



01/2/19 XL-1200(U)3.fm

31

R e f e r e n c e s

- S p e c i f i c a t i o n s -

SpecificationsAs part of our policy of continuous improvement, SHARP reservesthe right to make design and specification changes for productimprovement without prior notice. The performance specification fig-ures indicated are nominal values of production units. There may besome deviations from these values in individual units.

„ General

„ Amplifier

„ CD player

„ Tuner

„ Speaker

Power source AC 120 V, 60 Hz

Powerconsumption

33 W

Dimensions Width: 9-1/16" (230 mm)Height: 5-1/16" (128 mm)Depth: 11-9/16" (293 mm)

Weight 5.5 lbs. (2.5 kg)

Output power 8 watts minimum RMS per channel into 8ohms from 100 Hz to 20 kHz, 10% total har-monic distortion

Output terminals Speakers: 8 ohms

Headphones: 16 - 50 ohms (recommended:32 ohms)

CD digital output (optical)

Subwoofer (Audio signal): 500 mV/47 kohms

Input terminals Video/Auxiliary (audio signal): 500 mV/47kohms

Type Compact disc player

Signal readout Non-contact, 3-beam semiconductor laserpickup

D/A converter 1-bit D/A converter

Frequency

response

20 - 20,000 Hz

Dynamic range 90 dB (1 kHz)

Frequency range FM: 87.5 - 108 MHz

AM: 530 - 1,720 kHz

Type 2-way type speaker system

Tweeter

4" (10 cm) Woofer

Maximum inputpower

20 W

Rated input power 10 W

Impedance 8 ohms

Dimensions Width: 5-9/16" (140 mm)Height: 10-3/8" (263 mm)Depth: 7-3/8" (187 mm)

Weight 3.8 lbs. (1.7 kg)/each

sharp xl 1200 stereo user manual

Documents