sheartaptm - morse cutting tools nf 3 .354 .521 2c\, 34461 34462 — 34463 94461 94462 — 94463...

$: ShearTapTM - Morse Cutting Tools nf 3 .354 .521 2c\, 34461 34462 — 34463 94461 94462 — 94463 1/4-20 nc 3 .433 .567 2z\x — 34466 — 34467 — 94466 — 94467$
MACHINING APPLICATION SOLUTIONS

- for CArBoN steel ANd stAiNless steel up to 35 rC

- spirAl poiNt & spirAl flute

- optiMiZed GeoMetrY

- tABle 302A reduCed NeCK desiGN

- HiGH speed steel

- oXide / Nitride surfACe treAtMeNt & titANiuM Nitride (tiN) CoAted

ShearTapTM P R O D U C T I O N T A P S

P R O D U C T I O NS O L U T I O N S

ShearTapTM offers exceptional value for high volume production tapping in carbon steels and stainless steels up to 35Rc hardness. ShearTapTM features a new optimized flute

design for tremendous cutting edge strength and wear resistance, fast chip removal and perfect quality threads. A reduced neck and shorter thread length allow for

deeper hole tapping while enhancing coolant flow to the cutting teeth for extended tool life.

G E O M E T R Y Spiral Point Taps are designed for efficient tapping of through holes and blind holes with adequate depth for chip accumulation at the bottom of the hole. The shearing action of the point provides freer cutting action and ejects the chips ahead of the tap, eliminating chip disposal problems and chip damage to the threads. Shallower flutes also result in greater tap strength allowing for higher cutting speeds.

Spiral Flute Taps are designed to lift the chips out of the hole in blind hole tapping, eliminating chip disposal problems which can result in damaged threads and broken taps. They will also bridge openings, keyways and other interruptions in the tapped hole.

Plug Style (3-5 thread chamfer) is the most common chamfer used for tapping applications in through holes and blind holes with sufficient bottom clearance.

Modified Bottoming Style (2-2-1/2 thread chamfer) allows threading close to the bottom of blind holes but cuts more efficiently than standard bottoming taps due to a slightly longer chamfer which distributes the cutting load over a greater number of teeth.

CNC Reduced Neck Design enhances chip evacuation and cutting fluid flow to the cutting teeth for reduced friction, heat and galling. Also reduces contact between the tap and the work piece.

S U R F A C E F I N I S H E S / T O O L C O A T I N G S Steam Oxide Over Nitride Finish helps toughen the hard abrasion resistant nitrided base. Also reduces friction, loading and galling, helps retain cutting fluids, improves thread quality and extends tool life.

TiN - Titanium Nitride Coating increases wear resistance, reduces friction and galling, reduces tapping torque, improves thread quality and allows increased cutting speeds for greatly increased productivity and tool life.

ShearTapTM

HIGH PRODUCTION TAPSPREMIUM HIGH SPEED STEEL

H I G H V O L U M E P R O D U C T I O N T A P P I N G

CARBON STEELS • STAINLESS STEELS

2

Surface Treated TiN CoatedEDP No. EDP No.

SizeThread Type

No. of Flutes

Thread Length

Neck Length OAL H2 H3 H4 H5 H2 H3 H4 H5

4-40 NC 2 .313 .250 1M\, 34400 34401 — 34402 94400 94401 — 944026-32 NC 2 .375 .313 2 34404 34405 — 34406 94404 94405 — 944068-32 NC 3 .375 .375 2Z\, 34407 34408 — 34409 94407 94408 — 9440910-24 NC 3 .500 .375 2C\, — 34410 — — — 94410 — —10-32 NF 3 .500 .375 2C\, 34411 34412 — 34413 94411 94412 — 944131/4-20 NC 3 .625 .375 2Z\x 34416 34417 — 34418 94416 94417 — 944181/4-28 NF 3 .625 .375 2Z\x 34419 34420 34421 — 94419 94420 94421 —5/16-18 NC 3 .688 .438 2XC\cx — 34422 — 34423 — 94422 — 944235/16-24 NF 3 .688 .438 2XC\cx — 34424 34425 – — 94424 94425 —3/8-16 NC 3 .750 .500 2ZB\zn — 34426 — 34427 — 94426 — 944273/8-24 NF 3 .750 .500 2ZB\zn — 34428 34429 — — 94428 94429 —7/16-14 NC 3 .875 .563 3B\cx — 34430 — 34431 — 94430 — 944317/16-20 NF 3 .875 .563 3B\cx — 34432 — 34433 — 94432 — 944331/2-13 NC 3 .938 .719 3C\, — 34434 — 34435 — 94434 — 944351/2-20 NF 3 .938 .719 3C\, — 34436 — 34437 — 94436 — 944379/16-12 NC 4 1.000 .673 3Z>\cx — 34438 — — — 94438 — —9/16-18 NF 4 1.000 .673 3Z>\cx — 34439 — — — 94439 — —5/8-11 NC 4 1.125 .673 3ZC\zn — 34440 — — — 94440 — —5/8-18 NF 4 1.125 .673 3ZC\zn — 34441 — — — 94441 — —3/4-10 NC 4 1.219 .766 4Z\v — 34444 — — — 94444 — —3/4-16 NF 4 1.219 .766 4Z\v — 34445 — — — 94445 — —7/8-9 NC 4 1.344 .875 4ZZ\zn — — 34500 — — — 94500 —7/8-14 NF 4 1.344 .875 4ZZ\zn — — 34501 — — — 94501 —

1-8 NC 4 1.500 1.000 5Z\, — — 34502 — — — 94502 —1-12 NF 4 1.500 1.000 5Z\, — — 34503 — — — 94503 —1Z\,-7 NC 4 1.719 .843 5M\zn — — 34504 — — — 94504 —

1Z\,-12 NF 4 1.719 .843 5M\zn — — 34505 — — — 94505 —1Z\v-7 NC 4 1.719 .843 5C\v — — 34506 — — — 94506 —1Z\v-12 NF 4 1.719 .843 5C\v — — 34507 — — — 94507 —1C\,-6 NC 4 2.000 1.000 6Z\zn — — 34508 — — — 94508 —1C\,-12 NF 4 2.000 1.000 6Z\zn — — 34509 — — — 94509 —1Z\x-6 NC 6 2.000 1.000 6C\, — — 34510 — — — 94510 —1Z\x-12 NF 6 2.000 1.000 6C\, — — 34511 — — — 94511 —1C\v-5* NC 6 2.406 .782 7 — — — 34512* — — — 94512*2-4Z\x* NC 6 2.688 .874 7B\, — — — 34514* — — — 94514*

List No. 2090 — Steam Oxide Over Nitride

List No. 2090G — TiN Coated

STANDARD Machine Screw Sizes — 12 eachPACKAGE Fractional Sizes 1/4″ thru 1/2″ — 12 each 9/16″ thru 3/4″ — 3 each 7/8″ thru 2″ —1 each

*H7 Pitch Diameter Limit (sizes 1C\v-5 and 2-4Z\x)

Spiral PointShearTap™High Speed SteelPlug Style“Sheartap” offers exceptional value for high volume production tapping in carbon steels and stainless steels up to 35 Rc hardness.

Steam Oxide Over Nitride resists chip welding, increases lubricity and helps to retain cutting fluid. TiN Coating increases hardness and lubricity for improved thread quality, higher speeds and longer tool life.

Primarily designed for tapping through holes.

The spiral point forces the chips ahead of the tap.

3

List No. 2091 — Steam Oxide Over NitrideList No. 2091G — TiN Coated

STANDARD Machine Screw Sizes — 12 eachPACKAGE Fractional Sizes 1/4″ thru 1/2″ — 12 each 9/16″ thru 3/4″ — 3 each 7/8″ thru 2″ —1 each

*H7 Pitch Diameter Limit (sizes 1C\v-5 and 2-4Z\x)

Spiral FluteShearTap™High Speed Steel — 48° Helix AngleSemi-Bottoming Style“Sheartap” offers exceptional value for high volume production tapping in carbon steels, and stainless steels up to 35 Rc Hardness.


Surface Treated TiN CoatedThread No.of Thread Neck EDP No. EDP No.

Size Type Flutes Length Length OAL H2 H3 H4 H5 H2 H3 H4 H5

4-40 NC 3 .236 .327 1M\, 34450 34451 — — 94450 94451 — —

6-32 NC 3 .236 .452 2 34453 34454 — 34455 94453 94454 — 94455

8-32 NC 3 .236 .514 2Z\, 34456 34457 — 34458 94456 94457 — 94458

10-24 NC 3 .354 .521 2C\, 34459 34460 — — 94459 94460 — —

10-32 NF 3 .354 .521 2C\, 34461 34462 — 34463 94461 94462 — 94463

1/4-20 NC 3 .433 .567 2Z\x — 34466 — 34467 — 94466 — 94467

1/4-28 NF 3 .433 .567 2Z\x — 34468 34469 — — 94468 94469 —

5/16-18 NC 3 .472 .653 2XC\cx — 34470 — 34471 — 94470 — 94471

5/16-24 NF 3 .472 .653 2XC\cx — 34472 34473 — — 94472 94473 —

3/8-16 NC 3 .551 .699 2ZB\zn — 34474 — 34475 — 94474 — 94475

3/8-24 NF 3 .551 .699 2ZB\zn — 34476 34477 — — 94476 94477 —

7/16-14 NC 3 .591 .847 3B\cx — 34478 — 34479 — 94478 — 94479

7/16-20 NF 3 .591 .847 3B\cx — 34480 — 34481 — 94480 — 94481

1/2-13 NC 3 .630 1.026 3C\, — 34482 — 34483 — 94482 — 94483

1/2-20 NF 3 .630 1.026 3C\, — 34484 — 34485 — 94484 — 94485

9/16-12 NC 3 .690 .983 3Z>\cx — 34486 — — — 94486 — —

9/16-18 NF 3 .690 .983 3Z>\cx — 34487 — — — 94487 — —

5/8-11 NC 3 .745 1.052 3ZC\zn — 34488 — — — 94488 — —

5/8-18 NF 3 .745 1.052 3ZC\zn — 34489 — — — 94489 — —

3/4-10 NC 4 .820 1.165 4Z\v — 34492 — — — 94492 — —

3/4-16 NF 4 .820 1.165 4Z\v — 34493 — — — 94493 — —

7/8-9 NC 4 .911 1.308 4ZZ\zn — — 34520 — — — 94520 —

7/8-14 NF 4 .911 1.308 4ZZ\zn — — 34521 — — — 94521 —

1-8 NC 4 1.025 1.475 5Z\, — — 34522 — — — 94522 —

1-12 NF 4 1.025 1.475 5Z\, — — 34523 — — — 94523 —

1Z\,-7 NC 4 1.143 1.419 5M\zn — — 34524 — — — 94524 —

1Z\,-12 NF 4 1.143 1.419 5M\zn — — 34525 — — — 94525 —

1Z\v-7 NC 4 1.143 1.419 5C\v — — 34526 — — — 94526 —

1Z\v-12 NF 4 1.143 1.419 5C\v — — 34527 — — — 94527 —

1C\,-6 NC 4 1.333 1.667 6Z\zn — — 34528 — — — 94528 —

1C\,-12 NF 4 1.333 1.667 6Z\zn — — 34529 — — — 94529 —

1Z\x-6 NC 4 1.333 1.667 6C\, — — 34530 — — — 94530 —

1Z\x-12 NF 4 1.333 1.667 6C\, — — 34531 — — — 94531 —

1C\v-5* NC 6 1.600 1.588 7 — — — 34532* — — — 94532*2-4Z\x* NC 6 1.777 1.588 7B\, — — — 34534* — — — 94534*

Primarily designed for tapping blind holes.

The spiral flutes draw the chips out of the hole.

4

Metric ShearTap™Steam Oxide Over Nitride resists chip welding, increases lubricity and helps to retain cutting fluid. TiN Coating increases hardness and lubricity for improved thread quality, higher speeds and longer tool life.

Size Pitch

Pitch Dia.Limit

No. of Flutes

Thread Length

Neck Length OAL

Surface Treated EDP NO.

TiN Coated EDP NO.

M3 0.5 D3 2 .313 .313 1ZB\zn 35240 95240M3.5 0.6 D4 2 .375 .313 2 35241 95241M4 0.7 D4 3 .375 .375 2Z\, 35242 95242M5 0.8 D4 3 .500 .375 2C\, 35243 95243M6 1 D5 3 .625 .375 2Z\x 35244 95244M7 1 D5 3 .688 .438 2XC\cx 35245 95245M8 1 D5 3 .688 .438 2XC\cx 35246 95246M8 1.25 D5 3 .688 .438 2XC\cx 35247 95247

M10 1.25 D5 3 .750 .500 2ZB\zn 35248 95248M10 1.5 D6 3 .750 .500 2ZB\zn 35249 95249M12 1.25 D5 3 .938 .719 3C\, 35250 95250M12 1.75 D6 3 .938 .719 3C\, 35251 95251M14 1.5 D6 4 1.000 .673 3Z>\cx 35252 95252M14 2 D7 4 1.000 .673 3Z>\cx 35253 95253M16 1.5 D6 4 1.125 .673 3ZC\zn 35254 95254M16 2 D7 4 1.125 .673 3ZC\zn 35255 95255M18 1.5 D6 4 1.125 .719 4Z\cx 35256 95256M18 2.5 D7 4 1.125 .719 4Z\cx 35257 95257M20 1.5 D6 4 1.188 .812 4ZB\cx 35280 95280M20 2.5 D7 4 1.188 .812 4ZB\cx 35281 95281M22 1.5 D6 4 1.188 1.031 4ZZ\zn 35282 95282M22 2.5 D7 4 1.188 1.031 4ZZ\zn 35283 95283M24 2 D7 4 1.422 .797 4X>\cx 35284 95284M24 3 D8 4 1.422 .797 4X>\cx 35285 95285

Size Pitch

Pitch Dia.Limit

No. of Flutes

Thread Length

Neck Length OAL


TiN Coated EDP NO.

M3 0.5 D3 3 .236 .389 1ZB\zn 35258 95258M3.5 0.6 D4 3 .236 .452 2 35259 95259M4 0.7 D4 3 .236 .514 2Z\, 35260 95260M5 0.8 D4 3 .354 .521 2C\, 35261 95261M6 1 D5 3 .433 .567 2Z\x 35262 95262M7 1 D5 3 .472 .653 2XC\cx 35263 95263M8 1 D5 3 .472 .653 2XC\cx 35264 95264M8 1.25 D5 3 .472 .653 2XC\cx 35265 95265

M10 1.25 D5 3 .551 .699 2ZB\zn 35266 95266M10 1.5 D6 3 .551 .699 2ZB\zn 35267 95267M12 1.25 D5 3 .630 1.026 3C\, 35268 95268M12 1.75 D6 3 .630 1.026 3C\, 35269 95269M14 1.5 D6 3 .690 .983 3Z>\cx 35270 95270M14 2 D7 3 .690 .983 3Z>\cx 35271 95271M16 1.5 D6 3 .745 1.052 3ZC\zn 35272 95272M16 2 D7 3 .745 1.052 3ZC\zn 35273 95273M18 1.5 D6 4 .813 .983 4Z\cx 35274 95274M18 2.5 D7 4 .813 .983 4Z\cx 35275 95275M20 1.5 D6 4 .790 1.210 4ZB\cx 35290 95290M20 2.5 D7 4 .790 1.210 4ZB\cx 35291 95291M22 1.5 D6 4 .790 1.428 4ZZ\zn 35292 95292M22 2.5 D7 4 .790 1.428 4ZZ\zn 35293 95293M24 2 D7 4 .940 1.279 4X>\cx 35294 95294M24 3 D8 4 .940 1.279 4X>\cx 35295 95295

List No. 2090M — Steam Oxide Over NitrideList No. 2090G — TiN Coated

Spiral PointPlug Style

List No. 2091M — Steam Oxide Over NitrideList No. 2091G — TiN Coated

Spiral FluteSemi-Bottoming Style48° Helix Angle



STANDARD PACKAGE

M3-M12 — 12 eachM14-M18 — 3 eachM20-M24 —1 each



Pitch diameter limits are those recommended

for 6H class of thread.

5

Surface Treated

TiN Coated

Size No. of FlutesThread Length Neck Length OAL

Pitch Dia.Limit EDP NO. EDP NO.

1-1/8-8 4 1.143 1.419 5M\zn H5 34660 946601-1/4-8 4 1.143 1.419 5C\v H5 34661 946611-3/8-8 4 1.333 1.667 6Z\zn H5 34662 946621-1/2-8 4 1.333 1.667 6C\, H5 34663 946631-5/8-8 6 1.333 1.854 6ZZ\zn H6 34664 946641-3/4-8 6 1.600 1.588 7 H6 34665 946651-7/8-8 6 1.600 1.962 7B\zn H6 34666 94666

2-8 6 1.777 1.588 7B\, H6 34667 94667

Surface Treated

TiN Coated

Size No. of FlutesThread Length

Neck Length OAL

Pitch Dia. Limit EDP NO. EDP NO.

1-1/8-8 4 1.719 .843 5M\zn H5 34650 946501-1/4-8 4 1.719 .843 5C\v H5 34651 946511-3/8-8 4 2.000 1.000 6Z\zn H5 34652 946521-1/2-8 6 2.000 1.000 6C\, H5 34653 946531-5/8-8 6 2.000 1.187 6ZZ\zn H6 34654 946541-3/4-8 6 2.406 .782 7 H6 34655 946551-7/8-8 6 2.406 1.156 7B\zn H6 34656 94656

2-8 6 2.688 .874 7B\, H6 34657 94657



Eight PitchShearTap™Eight pitch taps are often required for applications in the power generation industry and general construction.

“Sheartap” offers exceptional value for high volume production tapping in carbon steels and stainless steels up to 35 Rc Hardness.


Spiral Point Eight Pitch SHEARTAP™

Plug Style

Spiral FluteEight Pitch SHEARTAP™

48° Helix Angle Semi-Bottoming StyleEight Pitch taps are often required for applications in the power generation industry and general construction.





6

SPEEDS shown are suggested starting points and may be increased or decreased depending on actual material and machining conditions. Start conservatively and increase until machining cycle is optimized.

SPEEDS may be increased for coated taps, spiral point taps, fine pitch taps, and when the percentage of thread is decreased.

SPEEDS may need to be decreased for uncoated taps, spiral flute taps, coarse pitch taps, bottoming taps, difficult materials, longer thread lengths, and when the percentage of thread is increased.

SHEARTAP™ Cutting Speeds

WORKPIECE MATERIAL

BRINELLHARDNESS

(BHN)

SURFACESPEED(SFM)

Low Carbon Steel – 1118, 12L12, 1108, 1213 ≤120 65

Low & Medium Carbon Steel – 1018, 1551, 11L44 120 - 250 40

Medium Carbon and Alloyed Steel – 1040, 1140, 4340, 8640 ≤250 40

Free Machining Stainless Steels – 303, 410, 416, 440F ≤260 35

Moderate Machining Stainless Steels – 304, 316 ≤300 20

Spiral PointPlug Style

InchList No. 2090 — Steam Oxide Over NitrideList No. 2090G — TiN Coated

MetricList No. 2090M — Steam Oxide Over NitrideList No. 2090G — TiN Coated

Spiral FluteSemi-Bottoming Style48° Helix Angle

InchList No. 2091 — Steam Oxide Over NitrideList No. 2091G — TiN Coated

MetricList No. 2091M — Steam Oxide Over NitrideList No. 2091G — TiN Coated

Spiral Point Spiral Flute

Size Thread TypePitch Dia.

Limit

Surface Treated

EDP NO.

TiN Coated

EDP NO.


TiN Coated

EDP NO.6-32 NC H7 34542 94542 34592 945928-32 NC H7 34544 94544 34594 9459410-24 NC H7 34546 94546 34596 9459610-32 NF H7 34548 94548 34598 945981/4-20 NC H7 34550 94550 34600 946001/4-20 NC H11 34551 94551 34601 946011/4-28 NF H7 34552 94552 34602 946021/4-28 NF H11 34553 94553 34603 946035/16-18 NC H7 34554 94554 34604 946045/16-18 NC H11 34555 94555 34605 946055/16-24 NF H7 34556 94556 34606 946065/16-24 NF H11 34557 94557 34607 946073/8-16 NC H7 34558 94558 34608 946083/8-16 NC H11 34559 94559 34609 946093/8-24 NF H7 34560 94560 34610 946103/8-24 NF H11 34561 94561 34611 946117/16-14 NC H11 34563 94563 34613 946137/16-20 NF H11 34565 94565 34615 946151/2-13 NC H11 34567 94567 34617 946171/2-20 NF H11 34569 94569 34619 946199/16-12 NC H11 34571 94571 34621 946219/16-18 NF H11 34573 94573 34623 946235/8-11 NC H11 34575 94575 34625 946255/8-18 NF H11 34577 94577 34627 946273/4-10 NC H11 34579 94579 34629 946293/4-16 NF H11 34581 94581 34631 946317/8-9 NC H11 34583 94583 34633 946337/8-14 NF H11 34585 94585 34635 94635

1-8 NC H11 34587 94587 34637 946371-12 NF H11 34589 94589 34639 94639

MetricM3 × 0.5 H7 34670 94670 34680 94690M4 × 0.7 H7 34671 94671 34681 94691M5 × 0.8 H7 34672 94672 34682 94692M6 × 1 H11 34673 94673 34683 94693

M8 × 1.25 H11 34674 94674 34684 94694M10 × 1.5 H11 34675 94675 34685 94695M12 × 1.75 H11 34676 94676 34686 94696

PITCH DIA. LIMIT

AMOUNT LARGER THAN BASIC PITCH DIA.

H7 .0030”-.0035”

H11 .0050”-.0055”

OversizeShearTap™Oversize taps are mainly used for parts that will be plated or heat treated after tapping. Also used in materials that tend to shrink after tapping.

Oversize ShearTaps

now available TiN Coated.

7

TAP DRILL SIZES METRIC TAP DRILL SIZESCutting Taps based

on approx. 75% thread

Forming Taps based on approx.

65% thread

Cutting Taps based on approx. 75% thread

Forming Taps based on approx.

65% thread

TAP SIZECUTTING TAP

DRILL SIZEFORMING TAP

DRILL SIZE TAP SIZECUTTING TAP

DRILL SIZEFORMING TAP

DRILL SIZE0-80 3/64 No. 54 M1.6 x 0.35 1.25mm 1.45mm1-64 No. 53 1.65mm M1.8 x 0.35 1.45mm 1/161-72 No. 53 1.7mm M2 x 0.4 1.60mm No. 492-56 No. 50 5/64 M2.2 x 0.45 1.75mm No. 422-64 No. 50 2.0mm M2.5 x 0.45 2.05mm No. 413-48 No. 47 No. 43 M3 x 0.5 2.5mm No. 343-56 No. 46 2.3mm M3.5 x 0.6 2.9mm 3.3mm4-40 No. 43 No. 39 M4 x 0.7 3.3mm 3.7mm4-48 No. 42 2.6mm M4.5 x 0.75 3.75mm 4.2mm5-40 No. 39 No. 33 M5 x 0.8 No. 19 No. 135-44 No. 38 2.9mm M6 x 1 5mm No. 26-32 No. 36 1/8 M7 x 1 6mm 6.5mm6-40 No. 33 3.2mm M8 x 1.25 H M8-32 No. 29 No. 25 M8 x 1 J 19/648-36 No. 29 No. 24 M10 x 1.5 8.5mm U10-24 No. 25 11/64 M10 x 1.25 8.75mm 9.5mm10-32 No. 21 No. 16 M12 x 1.75 13/32 7/1612-24 No. 17 5mm M12 x 1.25 10.75mm 11.5mm12-28 No. 15 No. 8 M14 x 2 12mm 33/641/4-20 No. 7 No. 1 M14 x 1.5 12.5mm 17/321/4-28 No. 3 A M16 x 2 14mm 19/32

5/16-18 F 7.3mm M16 x 1.5 14.5mm 39/645/16-24 I M M18 x 2.5 15.5mm 17mm3/8-16 5/16 S M18 x 1.5 16.5mm 11/163/8-24 Q T M20 x 2.5 17.5mm 18.75mm

7/16-14 U 13/32 M20 x 1.5 18.5mm 49/647/16-20 W 10.5mm M22 x 2.5 19.5mm 21mm1/2-13 27/64 11.8mm M22 x 1.5 20.5mm 27/321/2-20 29/64 12mm M24 x 3 53/64 57/649/16-12 31/64 17/32 M24 x 2 22mm

* Reaming Recommended

9/16-18 33/64 13.5mm M27 x 3 24mm5/8-11 17/32 14.75mm M27 x 2 63/645/8-18 37/64 15.25mm M30 x 3.5 1-3/64*3/4-10 21/32 45/64 M30 x 2 1-7/64*3/4-16 11/16 23/32 M33 x 3.5 1-11/64*7/8-9 49/64 M33 x 2 31mm*

7/8-14 13/16 M36 x 4 32mm*1-8 7/8 M36 x 3 33mm*

1-12 59/64 M39 x 4 35mm*1-14 15/16 M39 x 3 36mm*

HIGH PERFORMANCE TOOLSHIGH PRODUCTION TOOLS

PRODUCTION TOOLSSPECIAL APPLICATION TOOLS

31695 Stephenson Hwy.Madison Heights, MI 48071-1672

Phone: 248.588.2220 Fax: 248.588.2230Phone: 800.255.1701 Fax: 800.338.4857

www.morsecuttingtools.com

Always order from your local Morse distributor:

Flyer #22 Rev. #5 Rev. Date: 5-1-2009

sheartaptm - morse cutting tools nf 3 .354 .521 2c\, 34461 34462 — 34463 94461 94462 — 94463...

Documents