shopnotes #129 (vol22) - (may-jun.2013)
TRANSCRIPT
http:/
/www.th
etrav
ellere
st.co
m
http:/
/www.th
etrav
ellere
st.co
m
http:/
/www.th
etrav
ellere
st.co
m
http:/
/www.th
etrav
ellere
st.co
m
http:/
/www.th
etrav
ellere
st.co
m
http:/
/www.th
etrav
ellere
st.co
m
http:/
/www.th
etrav
ellere
st.co
m
http:/
/www.th
etrav
ellere
st.co
m
http:/
/www.th
etrav
ellere
st.co
m
carving duplicator Pattern
ShopNotes No. 129 Page 1 of 1 ©2013 August Home Publishing. All rights reserved.
TAPE BOTH HALVES OF PATTERN TOGETHER
ALONG DASHED LINES
Materials List
best-ever Planer Cart
ShopNotes No. 129 Page 1 of 1 ©2013 August Home Publishing. All rights reserved.
Cutting Diagram
1!/2" x 5!/2" - 96" HARD MAPLE (7.3 Bd. Ft.)
1!/2" x 5!/2"- 24" HARD MAPLE (1.8 Bd. Ft.)
48" x 96"- #/4" BIRCH PLYWOOD
!/4" x 24"- 24" BIRCH PLYWOOD
#/4" x 3!/2"- 24" HARD MAPLE (.6 Bd. Ft.)
NOTE: SAVE WASTE PIECE FROM SIDE (E) FOR MAKING LEAF SUPPORT (K)
A A A G
Q
E E
L
HJ
J
M
NN
OO
B B C C
P
D D D D
I F
K
48" x 96"- #/4" BIRCH PLYWOOD
GRAIN DIRECTION
A Platforms (3) 24 x 23 - 3⁄4 Ply.B Front/Back Supports (6) 11⁄2 x 11⁄2 - 23C Side Supports (6) 11⁄2 x 11⁄2 - 21D Corner Blocks (4) 11⁄2 x 4 - 4E Sides (2) 241⁄2 x 31 - 3⁄4 Ply.F Cart Cleat (1) 3⁄4 x 3⁄4 - 131⁄8
G Cart Back (1) 23 x 101⁄2 - 3⁄4 Ply.H Auxiliary Table (1) 13 x 31 - 3⁄4 Ply.I Table Cleat (1) 3⁄4 x 13⁄4 - 13J Side Fillers (2) 511⁄16 x 31 - 3⁄4 Ply. K Leaf Support (1) 113⁄4 x 157⁄8 - 3⁄4 Ply.
L Drop Leaf (1) 241⁄2 x 157⁄8 - 3⁄4 Ply.M Lower Filler (1) 241⁄2 x 15 - 3⁄4 Ply.N Drawer Sides (2) 91⁄2 x 20 - 3⁄4 Ply.O Drawer Front/Back (2) 91⁄2 x 21 - 3⁄4 Ply. P Drawer Bottom (1) 19 x 21 - 1⁄4 Ply.Q False Front (1) 227⁄8 x 103⁄8 - 3⁄4 Ply.
• (56) #8 x 11⁄2" Fh Woodscrews• (4) #8 x 11⁄4" Fh Woodscrews• (4) 3" Locking Swivel Casters• (16) #14 x 1" Lag Screws
• (16) 1⁄4" Flat Washers • (2) 36" Continuous Hinges w/Screws• (1 pr.) 11⁄2" x 20" Full-Ext. Drawer Slides • (1) 43⁄4" Drawer Pull
PATTERN GUIDES (SHOWN ACTUAL SIZE)
SMALL MEDIUM LARGE
NOTE: SHAPE SHOWN IS FOR “ROUND” SECTION
NOTE: MARK INDICATES WIDEST POINT
ROUND
OVAL
HANDLE
ShopNotes No. 129 Page 1 of 2 ©2013 August Home Publishing. All rights reserved.
pattern guides & gauge forOval Tool Handles
The patterns below help you lay out and shape each of the three sizes of handles while turning them. I used 1⁄4" plywood to make the pattern guides.
The gauge on page 2 helps ensure key features of the handles are prop-erly sized. The notches on one edge are for sizing the small handles. The
notches on the opposite edge apply to the medium and large handles. Just slip the notches over the features as you turn them.
GAUGE (SHOWN ACTUAL SIZE)
MEDIUM& LARGE
BEAD
TENON
TENON
BEAD
NECK
NECK
SMALL
%/8
#/8
#/4
!!/16
&/8
!/2
NOTE: GAUGE CAN BE MADE FROM !/4" PLYWOOD OR HARDBOARD
ShopNotes No. 129 Page 2 of 2 ©2013 August Home Publishing. All rights reserved.