side jamb liner replacement - andersen windows
TRANSCRIPT
“Andersen” and all other marks where denoted are trademarks of Andersen Corporation and its subsidiary. ©2013 Andersen Corporation. All rights reserved. 9069158 BA Revised 06/03/13
Side Jamb Liner Replacementfor E-Series Double-Hung
Thank you for choosing Andersen.
For questions call 1-888-888-7020. For more information and/or guides visit www.eaglewindow.com
Please leave this guide with building owner.
▶ Read guide from beginning to end before starting maintenance procedure. Read all warnings and cautions during unit maintenance.
Parts Included (1) Side Jamb Liner
▶ For information, calculating, and design pressure ratings for E-Series windows and doors go to www.eaglewindow.com/Wintelligence/Design-Pressure-Estimator.aspx
▶ Check with your local building code official to identify and confirm compliance with local building code requirements.
Tools Needed ∙ Safety Glasses ∙ Flat Blade Screw Driver ∙ Finish Nailer (for monumental units only) ∙ Pliers (for monumental units only) ∙ Putty Knife (for monumental units only)
Supplies Needed ∙ Denatured Alcohol ∙ Clean Cloth
Side Jamb Liner
Use caution when working at elevated heights and around unit openings. Follow manufacturers’ instructions for ladders and/or scaffolding. Failure to do so may result in injury or death.
Follow manufacturers’ instructions for hand or power tools. Always wear safety glasses. Failure to do so may result in injury and/or product damage.
Windows and doors can be heavy. Use safe lifting techniques and a reasonable number of people with enough strength to lift, carry and install window and door products to avoid injury and/or product damage.
29069158
Slide tilt latches inward while tilting sash in 90 degrees.
Tilt Latches
Tilt Latch
Lower top sash 6”.
6 Inches
6Interior
7Interior
Pivot bottom sash to remove from window frame as shown. Place sash on clean flat work surface, exterior side up.
Rotate and hold lock handles toward center while tilting sash in 90 degrees.
Unlock window and raise bottom sash 4".
Lock Handles
4 Inches
Lock Handles
2Interior
3Interior
4Interior
Bottom Sash
Bottom Sash
Pry interior side stop away from frame. Repeat on opposite side. Remove any nails from frame and interior side stops.
Remove sash stop from the side jamb.
For Monumental Only
Single Hung and Monumental Only
▶ For double hung units proceed to step 6.
1Interior
▶ For single and double hung units proceed to step 2.
5Interior
Pliers
Interior Side Stop
Pivot top sash to remove from window frame as shown. Place sash on clean flat work surface, exterior side up.
8Interior
Top Sash
Putty Knife
Interior Side Stop
39069158
Slide outside side jamb liner insert up 12”.
12 Inches
Pocket Cover
Grasp jamb liner pocket cover at bottom and pull outward and down from behind head stop to remove and save for reuse.
9Interior
12Interior
Outside Jamb LinerInsert
Insert flat blade screwdriver into cam slot, apply firm downward pressure, and rotate 1/4 turn. Hold firmly allowing shoe to rise until it stops. Repeat for other three balances.
BalanceShoe
ShoeBalanceCam
Flat BladeScrewdriver
Balance shoes are under high tension. Use flat blade screwdriver with long handle so that both hands can be used to release balance tension. Suddenly releasing balance shoe could damage window unit. Cam in unlocked
(travel) position2nd
1st
Cam in locked position
Remove existing sill cushion and save for reuse.
Sill Cushion
Flat BladeScrewdriver
11Interior
10Interior
49069158
Remove side jamb liner working from bottom to top, prying jamb liner edge from frame to disengage as shown.
Jamb Liner
Jamb Liner
13Interior
Pull side jamb liner down slowly, while supporting head stop and remove from frame. Dispose of side jamb liner properly.
14Interior
Insert new side jamb liner behind head stop.
15Interior
Position side jamb liner in frame, locking front lip behind interior side stop.
16Interior
Jamb Liner
InteriorSideStop
Jamb Liner
Re-engage side jamb liner, working from bottom to top, pressing jamb liner edge into frame to engage as shown.
17Interior Balance
Shoe
ShoeBalanceCam
Flat BladeScrewdriver
Unlocked Position
Locked Position
Insert flat blade screwdriver into cam and pull down until shoe is aligned with shoe on opposite side. Rotate cam 1/4 turn to lock.
18Interior
Side Jamb Liner
Head Stop
59069158
Slide outside side jamb liner insert down to sill.
19Interior
Jamb LinerExterior Insert
Clean area with a clean cloth and denatured alcohol.
Clean Cloth and Denatured Alcohol
20Interior
CheckrailWeatherstrip
Side CuttingPliers
Position wide end of sill cushion in jamb liner channel, adhesive side down, and press into place.
Sill Cushion
21Interior
Rotate top sash to engage pivot pins into balance shoes of exterior channel. Push down until both pivot pins are fully engaged.
Balance Shoes
Pivot Pin
22Interior
Tilt Latches
Tilt Latches
23Interior
Tilt sash up, retracting tilt latches by sliding inward. Release tilt latches to re-engage sash in frame. Verify top sash operation. Repeat steps 22-23 if sash does not operate correctly.
Insert top of jamb liner pocket cover, beveled side toward exterior, into interior channel, sliding it up behind head stop. Press jamb liner pocket cover firmly into place, starting at top, zippering down full length.
Jamb Liner Pocket Cover
InteriorChannel
Beveled Side24Interior
Jamb Liner Channel
Head Stop
Wide End
Sill Cushion
▶ For double hung units proceed to step 26.
69069158
Rotate bottom sash to engage pivot pins into balance shoes of interior channel. Push down until both pivot pins are fully engaged.
Balance Shoe
InteriorChannel
Pivot Pin
26Interior
Tilt sash up, retracting tilt latches by rotating lock handles toward center, then release lock handles to re-engage sash.
Lock Handles
27Interior
Verify sash operation. Repeat steps 26-27 if sash does not operate correctly.
Lock Handles
28Interior
Close and lock sash.
Lock Handles
30Interior
Verify sash operation. Repeat steps 30-31 if sash does not operate correctly.
Lock Handles
29Interior
▶ Side jamb liner replacement procedure is complete for monumental units.
Reapply interior side stop on frame. Repeat on opposite side. Fasten with finish nailer.
Interior Side Stop
For Monumental Only
31Interior
▶ Side jamb liner replacement procedure is complete for single and double hung units.
▶ For monumental units proceed to step 31.
Replace sash stop in the side jamb.
25Interior
Sash Stop
Single Hung and Monumental Only