sinks 2011...• reversible stainless steel/silver glass sliding sink covers accessories (suit...
TRANSCRIPT
1
SINKS
2011
2
VR78
3
about Smeg sinks 4
complementary designs 6
undermount sinks 8
topmount sinks 12
4
About Smeg sinks
At Smeg we understand that kitchen appliances need to be aesthetically beautiful and functional in equal measure. The humble kitchen sink has gone from a functional space in which to wash dishes, to a food preparation area, a drying area, a place to remove food scraps (perhaps via a food waste disposer) and, ultimately, to the focal point of a designer kitchen.
Smeg’s range of sinks vary from a simple, yet beautifully made, single bowl with drainer sink, through to the flagship of the range — a very sophisticated, double-bowl sink with elegant glass sliding chopping boards. A selection of sinks has been designed to specifically complement the iconic Smeg kitchen appliance ranges; for example, the LV range of sinks is shaped to perfectly correspond to the PGA range of cooktops, and the LD range will enhance the Marc Newson-designed range of ovens and cooktops. The design combination of Smeg Linear products with Smeg LQ sinks is superb.
Kitchen sinks are in most cases made of stainless steel, which is defined as a steel alloy with a minimum of 10.5–11% chromium content by mass. Stainless steel does not stain, corrode or rust as easily as ordinary steel. Stainless steel is austenitic — metallic but non magnetic. Smeg sinks are made from high-quality AISI304 (iron free) brushed stainless steel with a satin finish, 1mm thick is used for Smeg LD, LV, LQV, LQR, LR, VQ and VST ranges. The standard ranges are made with 0.6–0.7mm thick stainless steel.
The majority of Smeg sinks are made of lightly-brushed satin stainless steel to achieve the same finish as Smeg cooktops, ovens, rangehoods and refrigeration.
There are three methods of mounting sinks — topmount, flushmount and undermount. Topmounting is the standard method of installation, ie the sink is placed into a cutout and has a low profile.
For granite, marble, quartz resin and pure resin etc, flushmounting is often the preferred method as it achieves a completely flat surface. The ‘hole’ must be perfectly cut to accommodate the exact dimensions of the sink with a small rebate to accommodate the flush fitment of the visible trim. Undermounting is when the sink’s trim is perfectly concealed below the bench. It is important when installing undermount sinks that the manufacturer’s instructions are followed carefully, using silicon and the brackets provided. The sink should not be glued in place.
For both flush and undermounting, the sink should always be at hand for the qualified and skilled fabricator/stonemason to install.
5
About Smeg sinks
CLEANING
The premium-quality stainless which Smeg uses for its kitchen sinks is extremely durable. Over the course of its life, it will show signs of wear which may change its appearance but does not alter its integrity. Discolouration and marks which may appear on stainless steel are usually caused by water-borne deposits on its surface. Such stains often have a ‘rainbow effect’ and can be avoided by removing any wet objects (cloths etc) from the sink; it is helpful to dry the sink thoroughly after use.
Perforated rubber or plastic mats in the sink will cut down on scratching and marking by pans and tableware. Wash with a solution of dishwashing liquid detergent and water; or a solution of baking soda and water. Rinse and polish dry with paper towel or soft cloth. Never use scouring powders or steel wool as they will scratch stainless steel. You can brighten the sink by polishing with a cloth dipped in vinegar, or in ammonia, or dampen sink and a sponge, sprinkle a little baking soda on sponge and rub sink gently; rinse, then polish dry with a paper towel.
Smeg sinks, over time, actually improve with age. The day-to-day touching of plates, pots, utensils etc all add and improve the texture and appearance within its satin-finished surface.
25 YEAR
25252525252525252525252525252525252525252525252525252525252525252525252525252525252525252525252525252525252525252525252525252525252525GUARANTEE
6
Complementary
linear
classic
7
Complementary
marc newson
8
UNDERMOUNT
VSTQ20 undermount sink16 litres capacity
VSTQ40N undermount sink32 litres capacity
VSTQ72N undermount sink58 litres capacity
TLQ40 timber chopping board
TTQ40 polymer chopping board
VSH40Q single-bowl stainless steel drainer
VSH20Q half-bowl stainless steel drainer
Accessories
9
UNDERMOUNT
The VSTQ range was among the first hand-made bowls with 0° corners. The success of this range is due to a rigorous design which is in line with modern trends of simplicity and elegance in the kitchen.
NB: these are hand-made sinks; variations, though minimal, from indicated measurements might occur. Always have the sink(s) at hand when the qualified fabricator/stonemason is cutting out the benchtop. This will help ensure a perfect fit.
400420
420
400420
420
240202
438
400
10
UNDERMOUNT
BST30 undermount sink21.6 litres capacitydesigner waste & plug supplied
Accessories
DB30 drainer basket DB45 drainer basketDB34 drainer basket
TS30 chopping board TS45 chopping boardTS34 chopping board
BST45 undermount sink32.4 litres capacitydesigner waste & plug supplied
BST34 undermount sink24.5 litres capacitydesigner waste & plug supplied
11
UNDERMOUNT
UM4530 undermount sinkmain: 32.4 litres capacityauxiliary: 21.6 litres capacitydesigner waste & plug suppliedoverflow — plumbing kit supplied
UM3434 undermount sink24.3 litres capacity each bowldesigner waste & plug suppliedoverflow — plumbing kit supplied
UM4545 undermount sink32.4 litres capacity each bowldesigner waste & plug suppliedoverflow — plumbing kit supplied
760
450
340 34025 30 25
400180
760
450
340 34025 30 25
400180
OVERFLOW AND KIT
OVERFLOW AND KIT
OVERFLOW AND KIT
NB: these are hand-made sinks; variations, though minimal, from indicated measurements might occur. Always have the sink(s) at hand when the qualified fabricator/stonemason is cutting out the benchtop. This will help ensure a perfect fit.
12
TOPMOUNT
LE861A topmount sink24.5 litres capacitydesigner waste & plug suppliedno taphole — punched on request, L or R drainer area
LE862A topmount sink24.5 litres capacity each bowldesigner waste & plug suppliedno taphole — punched on request
Accessories
DB34 drainer basket TS34 chopping board
13
TOPMOUNT
LE116A topmount sink24.5 litres capacity each bowldesigner waste & plug suppliedno taphole — punched on request, L or R drainer area
LE102A topmount sinkmain: 24.5 litres capacityauxiliary: 10 litres capacitydesigner waste & plug suppliedno taphole — punched on request, L or R drainer area
TVN black glass chopping board
TVSG silver glass chopping board13
14
TOPMOUNT
LD861S topmount sink, left-hand drainerLD861D topmount sink, right-hand drainer27.2 litres capacitydesigner waste & plug suppliedpre-punched taphole, L or R drainer area
LD862 topmount sink27.2 litres capacity each bowldesigner waste & plug suppliedpre-punched taphole
LD116S topmount sink, left-hand drainerLD116D topmount sink, right-hand drainer27.2 litres capacity each bowldesigner waste & plug suppliedpre-punched taphole, L or R drainer area
Accessories
VSH40Q single-bowl stainless steel drainer
VSH20Q half-bowl stainless steel drainer
TVN black glass chopping board
TVSG silver glass chopping board
• modern design• 15mm radius corners• 20cm deep bowls• low profile• easy to clean• overflow and plumbing kit supplied• high-quality 1mm thick brushed stainless
steel
OVERFLOW AND KIT
OVERFLOW AND KIT
OVERFLOW AND KIT
15
TOPMOUNT
LD861D/S
LD862
LD116D/S
TVN/TVSG
16
TOPMOUNT
LV951S-3 topmount sink, left-hand drainerLV951D-3 topmount sink, right-hand drainer36 litres capacitydesigner waste & plug suppliedpre-punched taphole, L or R drainer area
LV116S-3 topmount sink, left-hand drainerLV116D-3 topmount sink, right-hand drainer24.5 litres capacity each bowldesigner waste & plug suppliedpre-punched taphole, L or R drainer area
LV95-3 topmount sink24.5 litres capacity each bowldesigner waste & plug suppliedpre-punched taphole
DB45 drainer basket
DB34 drainer basket
TS45 chopping board
TS34 chopping board
Accessories
OVERFLOW AND KIT
OVERFLOW AND KIT
OVERFLOW AND KIT
17
TOPMOUNTLV951D/S-3
LV116D/S-3
LV95-3
18
TOPMOUNT
LQVS862-1• 31.5 litres capacity each bowl• three pre-punched holes for tap fitment two
remote-control designer plug & waste• reversible stainless steel/silver glass sliding sink
covers
Accessories(suit LQVS862-1, LQVN862-1)
TLQ40 timber chopping board
TTQ40 polymer chopping board
LQVN862-1• 31.5 litres capacity each bowl• three pre-punched holes for tap fitment and two
remote-control designer plug & waste• reversible stainless steel/black glass sliding sink
covers
The LQV range features hand-made, 1mm-thick stainless steel bowls with glass/stainless steel sliding work surface. The design complements perfectly the Smeg Linear range of appliances. The designer pop-up plug and waste includes a stainless steel cover. Also included is a sliding 150mm-wide stainless steel colander.
OVERFLOW AND KIT
OVERFLOW AND KIT
1.0
7.5
19
TOPMOUNT
VR78S67 litres capacitytwo pre-punched holes in rear platform for tap and single remote control plug and waste
Beautiful and practical, the VQ78R is hand-built of 1mm thick stainless steel, with silver glass chopping boards and sliding stainless steel colander.
FEATUREdesigner pop-up plug and wastewith stainless steel cover
20
TOPMOUNT
LQR862-2 topmount sink30 litres capacity each bowltwo pre-punched holes for tap and remote control for designer waste & plug, either bowl (supplied)
LQR100-2 topmount sinkmain: 29.6 litresauxiliary: 14.7 litrestwo pre-punched holes for tap and remote control for outer bowl designer waste & plug (supplied) — reversible for L or R drainer area
LQR116-2 topmount sink30 litres capacity each bowltwo pre-punched holes for tap and remote control for outer bowl designer plug and waste (supplied) — reversible for L or R drainer area
The VQ range of sinks was amongst the first hand-made bowls with 0° corners. The success of this range is due to
a rigorous design which is in line with the modern trends of simplicity and elegance in the kitchen.
Accessories
TLQ40 timber chopping board
TTQ40 polymer chopping board
VSH40Q single-bowl stainless steel drainer
VSH20Q half-bowl stainless steel drainer
remote control for designer waste &
OVERFLOW AND KIT OVERFLOW
AND KIT
OVERFLOW AND KIT
21
TOPMOUNT
NB: each LQR sink is prepunched with two holes in either end of the stainless steel bridge between the two sink bowls. Depending on your drainer side, one hole will be fitted with the remote control square knob to raise or lower strainer plug in the bowl; the other hole will be for the tap.
22
TOPMOUNT
VQ20 topmount sink16.8 litres capacity designer waste & plug supplied
VQ40NR topmount sink33.6 litres capacitydesigner waste & plug supplied
VQ40N topmount sink33.5 litres capacity designer waste & plug supplied
Accessories
TLQ40 timber chopping board
TTQ40 polymer chopping board
VSH40Q single-bowl stainless steel drainer
VSH20Q half-bowl stainless steel drainer
OVERFLOW AND KIT
OVERFLOW AND KIT
OVERFLOW AND KIT
23
TOPMOUNTVQ20N
VQ40N
VQ40NR
10
24
TOPMOUNT OR FLUSHMOUNT
LR102 sinkmain: 30 litresauxiliary: 6 litrestwo pre-punched holes for tap and remote control for outer bowl designer plug and waste (supplied) — reversible for L or R drainer area
LR861 sink30 litres capacity designer waste & plug suppliedtwo pre-punched holes for tap and remote control for outer bowl designer plug and waste (supplied) — reversible for L or R drainer area
1.25
+10.5
OVERFLOW AND KIT
OVERFLOW AND KIT
25
1.0
7.5
TOPMOUNT OR FLUSHMOUNT
VR80 sink64.8 litres capacitytwo pre-punched holes for tap and remote control for designer plug and waste (supplied)
With the elegant and minimal design of a squareline sink, 10mm radius corners have been introduced to the LR/VR range of sinks for ease of cleaning
Accessories
TLQ40 timber chopping board
TTQ40 polymer chopping board
VSH40Q single-bowl stainless steel drainer
VSH20Q half-bowl stainless steel drainer
26
27
Smeg Australia Pty Ltd
Sydney Head Office 02 8667 4888
Smeg Service 02 8667 4833
Smeg Spare Parts 02 8667 4875
Smeg Melbourne 03 9094 1999
Australia-wide distributors:
Newcastle 02 4960 9266
Wagga Wagga 02 6922 8600
ACT 02 6280 7099
Queensland 07 3266 0444
Tasmania 03 6334 8166
South Australia 08 8346 1888
Western Australia 08 9478 0466
Smeg Australia Pty Ltd is constantly seeking ways to improve the specifications, design and production of its products. Alterations take place continually. Whilst every effort is made to produce up-to-date literature, this brochure should not be regarded as an infallible guide to the current specifications, nor does it constitute an offer for the sale of any particular product. Product cutouts indicated in our literature are indicative only. Actual product only should be used to define cutout sizes. Distributors, agents and retailers are not agents of Smeg Australia and have no authority to bind Smeg Australia by any express or implied undertaking or representation.
www.smeg.com.au
WARNING: technical specifications and product sizes can be varied by the manufacturer without notice. Cutouts for appliances should only be by physical product measurements. The above information is indicative only.
28