Machine application

Discover advantages of Ceresit CT 174 MACHINE

Application Plaster.

Smart wayof plastering

Work goes easier and faster than ever!

Ceresit CT 174 MACHINE Application Plaster guarantees a smart way of plastering. The product allows you to finish work with less effort, in shorter time and the final effect is always perfect. All you need is Ceresit CT 174 MACHINE and a spraying machine!

Advantages of Ceresit CT 174 MACHINE Application Plaster Silicate-silicone plaster, stone like structure, grain 1,0 mm

With Ceresit CT 174 MACHINE you can forget about problems of manual technique e.g. visible levels of the scaffolding and direction of structuring. You can easily achieve homogenous structure without ‘woodworm’ effects and make corrections if needed.

With Ceresit CT 174 MACHINE you do not need to create the structure manually. It means that youcan benefit from less application steps and make your work easier.

Ceresit CT 174 MACHINE allows you to speed up application significantly.With the machine you can plaster 600-800 m2 per day with 1 applicator and 2 helpers instead of 100-150 m2

with 2 applicators and 2 persons for structuring.

The fast, easy and efficient working withCeresit CT 174 MACHINE, allows to save

on labour costs. Additionally, with low and precise consumption of the product you save money.

Ceresit CT 174 MACHINE can be easily applied in any temperature (from +5 to +30°C).

As there is no need of structuring the surface, you do not have to speed up your work due to faster drying of the

plaster in high temperature.

Due to mechanical application, which is fast andconvenient, Ceresit CT 174 MACHINE is highly

recommended to finish large objects.

Due to low product consumption (approx. 1,5 kg/m2), one container of Ceresit CT 174 MACHINE can cover

around 17 m2 of the wall. To compare, regular wet plaster consumption is 2,5-3,0 kg/m2

Ceresit CT 174 MACHINE Application Plaster Ceresit CT 174 MACHINE Application Plaster

Ceresit CT 174 machine application plaster

• for dedicated ETICS applications and bigger objects we recommend SPG Baumaschinen PG 20 Plaster spraying machine or Wagner PC 830 Compact plaster aggregate

• for smaller objects (walls up to 100 m2) we advice to use 100 l air compressor with plaster spray gun

Worm pump, nozzle size 6-10 mm, delivery rate c.a. 8-10 l/min., working pressure up to 40 bar:

Application steps of Ceresit CT 174 MACHINE Application Plaster

PROTECTION OF DOORS AND WINDOWS. Doors, windows and a plinth area should be covered and sealed with the plastic foil. Tape position along the plinth will determine the edge line of the plaster, so perform taping in a straight line.

MACHINE PREPARATION. If using a plaster spraying machine SPG PG 20 or similar device, assemble all the parts following manufacturers recommendations.

PLASTERING TRIAL. Spray a spare board(e.g. gypsum cardboard) to check the air pressure,the size of the nozzle and spraying fluency.

CLEANING. Immediately after spraying, disassemble all the parts and wash them thoroughly. Clean the hopper, the hose and the nozzle with water.

DRYING. To conduct further works, wait until surface is completely dry. Faster or slower drying of the plaster may occur in different conditions.

PRIMING. Prime the substrate with the suitable agent – we recommend to use priming paint CT 16 in colour similar to the colour of the plaster. Plaster can be sprayed when the primer becomes completely dry.

MACHINE FILLING. First, pour some of the primingpaint into the hopper and pump it out. This will later provide an easy flow of the plaster. Next, stir CT 174 MACHINE plaster and pour it into the machine.

PLASTER APPLICATION. Place the nozzle vertically approx 40 - 60 cm from the wall and spray the surface with smooth, round moves.

4

1

5

7 8

3

2

6

Machine application requirements

Ceresit CT 174 MACHINE Application Plaster Ceresit CT 174 MACHINE Application Plaster

Cost-saving in materials

Cost-saving in labour

Cost-saving in time

CT 174 MACHINE

Ceresit CT 174 MACHINE Application Plaster Ceresit CT 174 MACHINE Application Plaster

Type of application

Manually applied wet plaster CT 174 MACHINE

Number of workers 4 workers 3 workers

Application 2 workers 1 worker

Structuring 2 workers -

Helping - 2 workers

Time 16 days 3 days

Quantity of material around 5 tons up to 3 tons

Ceresit CT 174 MACHINE plaster is available in 211 Colours of Nature. From delicate blues of the oceans to succulent shades of greens and friendly tones of brickreddish earth – all colours of the concept are derived from the beauty of nature. The plaster can be tinted in many other colours on request.

Adhesive mortar

CT 85 CT 190

CT 325 CT 325

CT 83 CT 180

EPS MWInsulation material

Reinforced layer

Mesh

Ceresit CT 174 MACHINE

Foamed polystyrene based system

Manually applied wet plaster

Mineral wool based system

Ceresit CT 174 MACHINE Application Plaster as a part of Ceresit Ceretherm insulation systems

Plastering building’s facade of 2000 m2

Your benefits

CER

XXXX

_XX.

XX_X

XXX

Henkel CEE

Erdbergstraße 29,A-1030 Vienna,AustriaTel.: +43 171 10 44 336www.ceresit.comwww.ceresit-visage.comwww.ceresit-impactum.com