smdk-bridge-board manual · 6. appendix 6.6 dc5v supply for s1r72v27 eva boad s1r72v27 eva board...
TRANSCRIPT
SMDK-BRIDGE-BOARD Manual
Rev.1.00
NOTICE
No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or circuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such as, medical products. Moreover, no license to any intellectual property rights is granted by implication or otherwise, and there is no representation or warranty that anything made in accordance with this material will be free from any patent or copyright infringement of a third party. This material or portions thereof may contain technology or the subject relating to strategic products under the control of the Foreign Exchange and Foreign Trade Law of Japan and may require an export license from the Ministry of Economy, Trade and Industry or other approval from another government agency. All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective companies..
©SEIKO EPSON CORPORATION 2009, All rights reserved.
Scope
This document applies to the SMDK-BRIDGE-BOARD released by SEIKO EPSON.
Table of Contents
1. Overview............................................................................................................................................ 1
2. Jumper Settings................................................................................................................................ 2
3. SMDK Board Interface ...................................................................................................................... 3
4. EVA Board Interface.......................................................................................................................... 3
5. Power Supply .................................................................................................................................... 3
6. Appendix............................................................................................................................................ 4
6.1 External View........................................................................................................................... 4 6.2 Circuit Diagram........................................................................................................................ 5 6.3 Components List...................................................................................................................... 5 6.4 Circuit Board Dimensional Diagram......................................................................................... 5 6.5 Connection .............................................................................................................................. 6 6.6 DC5V supply for S1R72V27 EVA Boad ................................................................................... 7 6.7 S1R72V27 EVA Board Jumper settings................................................................................. 10
SMDK-BRIDGE-BOARD Manual Seiko Epson Corporation i (Rev. 1.00)
1. Overview
1. Overview
This “SMDK-BRIDGE-BOARD” is a joint board between SMDK6400/6410 and S1R72V27 Evaluation Board.
(Note)
SMDK6400/6410 : SAMSUNG Mobile Development Kit
SMDK-BRIDGE-BOARD Manual Seiko Epson Corporation 1 (Rev. 1.00)
2. Jumper Settings
2. Jumper Settings
Set the jumpers on the board as they are suitable for your evaluation environment. Settings marked “*” as shown Table 2-1 are default settings.
No. Details Setting (* indicates default) JP1 XINT selection * 1-2 XINT connects XEINT3
1-3 XINT connects XEINT4 JP2 XDREQ selection * 1-2 XDREQ connects XuRXD_2/ExdREQ
1-3 XDREQ connects XuRXD_3/ExdREQ JP3 XDACK selection * 1-2 XDACK connects XuTXD_2/ExdACK
1-3 XDACK connects XuTXD_3/ExdACK JP4 XRESET selection * 1-2 XRESET connects nReset from SMDK
1-3 XRESET connects on this board XRESET
Table 2-1 Jumper Settings
Fig.2-1 Jumper Settings
JP1, JP2, JP3, JP4
2 Seiko Epson Corporation SMDK-BRIDGE-BOARD Manual (Rev. 1.00)
3. SMDK Board Interface
3. SMDK Board Interface
Connect JF1 on SMDK6400/6410 via CN1 on this board. Refer to “6.2 Circuit Diagrams” for pin assignment specifics. The CN1 connector and mating connector are provided as shown below.
CN1 : QSE-040-01-L-D-EM2 / SAMTEC
Opposite side : QTE-040-01-L-D-EM2 / SAMTEC
4. EVA Board Interface
Connect CN4 on S1R72V27 Evaluation Board via CN2 on this board. Refer to “6.2 Circuit Diagrams” for pin assignment specifics. The CN2 connector and mating connector are provided as shown below.
CN2 : NDS100-002-BF / Yamaichi Electronics
Opposite side : NDP100-002-BF / Yamaichi Electronics
5. Power Supply
This board don’t have a connector for Power Supply.
It’s no need for this board to supply power especially from extenal.
SMDK-BRIDGE-BOARD Manual Seiko Epson Corporation 3 (Rev. 1.00)
6. Appendix
6. Appendix
6.1 External View
Fig.6-1 External View
CN1:
SMDK Board Interface
CN2:
EVA Board Interface
4 Seiko Epson Corporation SMDK-BRIDGE-BOARD Manual (Rev. 1.00)
6. Appendix
6.2 Circuit Diagram Refer to attachments.
6.3 Components List Refer to attachments.
6.4 Circuit Board Dimensional Diagram External dimensions: 40.00 x 100.00 [mm]
Fig.6-2 Circuit Board Dimensional Diagram
[Unit: mm]
SMDK-BRIDGE-BOARD Manual Seiko Epson Corporation 5 (Rev. 1.00)
6. Appendix
6.5 Connection SMDK6400/6410 and SMDK-BRIDGE-BOARD connect to use External ROM Bus port (JF1) on SMDK6400/6410.
Fig.6-3 Connection between SMDK6400 and S1R72V27 EVA Board
JF1
Fig.6-4 Connection between SMDK6410 and S1R72V27 EVA Board
JF1
6 Seiko Epson Corporation SMDK-BRIDGE-BOARD Manual (Rev. 1.00)
6. Appendix
6.6 DC5V supply for S1R72V27 EVA Boad S1R72V27 EVA Board needs to be supplied DC5V without via SMDK-BRIDGE-BOARD. Because
JF1 on SMDK6400/6410 doesn’t have any pins for DC5V. On the other hands, JF1 has GND pins. So GND on SMDK6400/6410 connects both GND on SMDK-BRIDGE-BOARD and ones on S1R72V27 EVA Board. Please make a cable for DC5V to connect between SMDK6400/6410 and S1R72V27 EVA Board.
Case.1 SMDK6400 to S1R72V27 EVA Board
Fig. 6-5 SMDK6400 DC5V output point:J4_1pin (B_PWR_5V)
Fig. 6-6 S1R72V27 EVA Board DC5V input point (red cable):CN7_1pin
SMDK-BRIDGE-BOARD Manual Seiko Epson Corporation 7 (Rev. 1.00)
6. Appendix
Case.2 SMDK6410 to S1R72V27 EVA Board
Fig. 6-7 SMDK6410 DC5V output point:CON4_1pin (DC_5V) with SW5 sets PWR ON
SW5:PWR ON
Fig. 6-8 S1R72V27 EVA Board DC5V input point (red cable):CN7_1pin
8 Seiko Epson Corporation SMDK-BRIDGE-BOARD Manual (Rev. 1.00)
6. Appendix
If the current on DC5V from SMDK6400/6410 is not sufficient, supply DC5V from a external power unit to S1R72V27 EVA Board directly. In this case, turn on and off DC5V at the same timing both SMDK6400/6410 and S1R72V27 EVA Board.
Case.3 a External power unit to S1R72V27 EVA Board
Fig. 6-9 S1R72V27 EVA Board DC5V input point
DC5V (red cable):CN7_1pin GND (black cable):CN7_2pin
SMDK-BRIDGE-BOARD Manual Seiko Epson Corporation 9 (Rev. 1.00)
6. Appendix
6.7 S1R72V27 EVA Board Jumper settings Fig6-10 CN2, CN3
CN2:1pin_2pin short CN3:1pin_2pin short
Fig6-11 JP3 (Solder Jumper)
JP3
CN2、SN3
JP3:CVDD_3.3V short
Please set this Jumper as suitable for your evaluation environment.
10 Seiko Epson Corporation SMDK-BRIDGE-BOARD Manual (Rev. 1.00)
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
CA8
CA7CA6CA5CA4CA3CA2CA1
B_ADDR1B_ADDR3B_ADDR5B_ADDR7
B_ADDR2B_ADDR4B_ADDR6
B_ADDR8
B_DATA1B_DATA3B_DATA5B_DATA7
B_DATA9B_DATA11B_DATA13B_DATA15
B_DATA0B_DATA2B_DATA4B_DATA6
B_DATA10B_DATA12B_DATA14
B_DATA8
CD15CD14CD13CD12CD11CD10CD9CD8
CD7CD6CD5CD4CD3CD2CD1CD0
CA9CA10
B_ADDR10B_ADDR9
B_ADDR1
B_ADDR2
B_ADDR3
B_ADDR4
B_ADDR5
B_ADDR6
B_ADDR7
B_ADDR8
B_ADDR9
B_ADDR10
CA1
CA2
CA3
CA4
CA5
CA6
CA7
CA8
CA9
CA10
XRESET
XnRSTOUT
XuTXD2/ExdACKXuTXD3/ExdACK
XuRXD2/ExdREQXuRXD3/ExdREQ
XEINT3XEINT4
CD0
CD1
CD2
CD3
CD4
CD5
CD6
CD7
CD8
CD9
CD10
CD11
CD12
CD13
CD14
CD15B_DATA15
B_DATA14
B_DATA13
B_DATA12
B_DATA11
B_DATA10
B_DATA9
B_DATA8
B_DATA7
B_DATA6
B_DATA5
B_DATA4
B_DATA3
B_DATA2
B_DATA1
B_DATA0
B_ADDR[10:1]
B_nBE0
nCS_EXTB_WEn
B_DATA[15:0]
B_nBE0
nCS_EXT
B_OEn
B_nBE1
B_WEn
XEINT3
XEINT4
XuRXD2/ExdREQ
XuRXD3/ExdREQ
XuTXD2/ExdACK
XuTXD3/ExdACK
XCS
XRDXBEHXWR
XINT
XDREQXDACK
XBEL
3.3V
CA11CA12CA13CA14CA15
B_ADDR11B_ADDR13B_ADDR15
B_ADDR12B_ADDR14
B_OEn
CD[15:0]
CA[10:1]
CD1
CD0
CA1
CA2
5V
B_nBE1
Title
Size Document Number Rev
Date: Sheet of
<Doc> 1.0
Bridge Board
A3
1 1Monday, September 01, 2008
Title
Size Document Number Rev
Date: Sheet of
<Doc> 1.0
Bridge Board
A3
1 1Monday, September 01, 2008
Title
Size Document Number Rev
Date: Sheet of
<Doc> 1.0
Bridge Board
A3
1 1Monday, September 01, 2008
LA22LA22
R10 0R10 0
LA5LA5
R28 0R28 0
R21 0R21 0
U1
MCP100-270DI/TO
U1
MCP100-270DI/TO
RST
VDD
GN
D
LA8LA8
LA26LA26
TP12TP12
TP8TP8
R17 0R17 0
LA30LA30LA16LA16
TP4TP4
LA23LA23
R29 0R29 0
R11 0R11 0
JP3JP3
12
3
R22 0R22 0
R35 270R35 270
JP2JP2
12
3
TP10TP10
JP1JP1
12
3
D1
TLGV1022(F)
D1
TLGV1022(F)
LA29LA29
JP4JP4
12
3
TP1TP1
LA1LA1
R18 0R18 0
R1 0R1 0
TP5TP5
R2 0R2 0
R30 0R30 0
R12 0R12 0
TP6TP6
R23 0R23 0
R3 0R3 0
TP11TP11
D2
TLGV1022(F)
D2
TLGV1022(F)
TP7TP7
LA18LA18
CN2
NDS100-002-BF
CN2
NDS100-002-BF
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
B1
B2
B3
B4
B5
B6
B7
B8
B9
B11
B12
B13
B14
B15A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
A33
A34
A35
A36
A37
A38
A39
A40
A41
A42
A43
A44
A45
A46
A47
A48
A49
A50
B10
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
B32
B33
B34
B35
B36
B37
B38
B39
B40
B41
B42
B43
B44
B45
B46
B47
B48
B49
B50
U2
TC7WH00FU
U2
TC7WH00FU
1A11B22Y3GND4 2A 52B 61Y 7Vcc 8 LA25LA25
U3
TC7WH02FU
U3
TC7WH02FU
1A11B22Y3GND4 2A 52B 61Y 7Vcc 8
LA27LA27
LA2LA2
J1J1
12
TP9TP9
R31 0R31 0
R13 0R13 0
R24 0R24 0
LA12LA12 LA19LA19
LA6LA6
LA17LA17
R36 270R36 270
TP3TP3
LA9LA9
LA24LA24
R4 0R4 0
LA28LA28
CN1
QSE-040-01-L-D-EM2
CN1
QSE-040-01-L-D-EM2
1 23 45 67 89 10
11 1213 1415 1617 1819 2021 2223 2425 2627 2829 3031 3233 3435 3637 3839 4041 4243 4445 4647 4849 5051 5253 5455 5657 5859 6061 6263 6465 6667 6869 7071 7273 7475 7677 7879 80
TP14TP14
R5 0R5 0
R32 0R32 0
TP15TP15
LA3LA3
R14 0R14 0
TP2TP2
R25 0R25 0
LA13LA13 LA20LA20
R19 0R19 0 TP16TP16
U4
TC7WH04FU
U4
TC7WH04FU
1A1
2A3 3A 63Y2 1Y 7
2Y 5GND4
Vcc 8
LA31LA31
R33 0R33 0
R6 0R6 0
R15 0R15 0
R26 0R26 0
LA14LA14
LA4LA4
LA21LA21
LA7LA7
R27 0R27 0
R7 0R7 0
R20 0R20 0
LA10LA10
R8 0R8 0
TP13TP13
LA11LA11
R9 0R9 0
R34 0R34 0
R16 0R16 0
LA15LA15
LA32LA32
SMDK-BRIDGE-BOARD Components List
■Boardreference Quantity Maker Part Name Note
CN1 1 SAMTEC QSE-040-01-L-D-EM2CN2 1 YAMAICHI NDS100-002-BFD1,D2 2 TOSHIBA TLGV1022(F)
JP1,JP2,JP3,JP4 4 MAC8 WL-1-3PJS1,JS2,JS3,JS4 4 MAC8 JS-1 for JP1,JP2,JP3,JP4J1 1 MAC8 WL-1-2P
LA1,LA2,LA3,LA4,LA5,LA6,LA7,LA8,LA9,LA10,LA11,LA12,LA13,LA14,LA15,LA16,LA17,LA18,LA19,LA20,LA21,LA22,LA23,LA24,LA25,LA26,LA27,LA28,LA29,LA30,LA31,LA32 32 no_maker landR1,R2,R3,R4,R5,R6,R7,R8,R27,R28,R29,R30,R31,R33,R34 15 ROHM MCR03EZHJ101R11,R12,R13,R14,R15,R16,R17,R18,R19,R20,R21,R22,R23,R24,R25,R26 16 ROHM MCR03EZHJ560R9,R10,R32 2 ROHM MCR03EZHJ000R35,R36 2 ROHM MCR03EZHJ271TP1,TP2,TP3,TP4,TP5,TP6,TP7,TP8,TP9,TP10,TP11,TP12 12 MAC8 LC-33-S(Yellow)
TP13,TP14,TP15,TP16 4 MAC8 LC-33-S(Black)
U1 1 MICROCHIP MCP100-270DI/TO TO-92U2 1 TOSHIBA TC7WH00FU No mountU3 1 TI SN74LVC2G02DCTR No mountU4 1 TOSHIBA TC7WH04FU No mount
■Accessoryreference Quantity Maker Part Name Note
- 1 no_maker Cable
for DC5V supplyfrom SMDK6400/6410to S1R72V27 EVA Board
Revision History
Revision History Revision details
Date Rev. Page Type Details 08/17/2009 1.00 All pages New New issue
International Sales Operations
AMERICA EPSON ELECTRONICS AMERICA, INC. 2580 Orchard Parkway, San Jose, CA 95131, USA Phone: +1-800-228-3964 FAX: +1-408-922-0238 EUROPE EPSON EUROPE ELECTRONICS GmbH Riesstrasse 15, 80992 Munich, GERMANY Phone: +49-89-14005-0 FAX: +49-89-14005-110
ASIA EPSON (CHINA) CO., LTD. 7F, Jinbao Bldg., No.89 Jinbao St., Dongcheng District, Beijing 100005, CHINA Phone: +86-10-6410-6655 FAX: +86-10-6410-7320
SHANGHAI BRANCH 7F, Block B, Hi-Tech Bldg., 900 Yishan Road, Shanghai 200233, CHINA Phone: +86-21-5423-5522 FAX: +86-21-5423-5512
SHENZHEN BRANCH 12F, Dawning Mansion, Keji South 12th Road,Hi-Tech Park, Shenzhen 518057, CHINA Phone: +86-755-2699-3828 FAX: +86-755-2699-3838 EPSON HONG KONG LTD. 20/F, Harbour Centre, 25 Harbour Road, Wanchai, Hong Kong Phone: +852-2585-4600 FAX: +852-2827-4346 Telex: 65542 EPSCO HX EPSON TAIWAN TECHNOLOGY & TRADING LTD. 14F, No. 7, Song Ren Road, Taipei 110, TAIWAN Phone: +886-2-8786-6688 FAX: +886-2-8786-6660 EPSON SINGAPORE PTE., LTD. 1 HarbourFront Place, #03-02 HarbourFront Tower One, Singapore 098633 Phone: +65-6586-5500 FAX: +65-6271-3182 SEIKO EPSON CORP. KOREA OFFICE 50F, KLI 63 Bldg., 60 Yoido-dong, Youngdeungpo-Ku, Seoul 150-763, KOREA Phone: +82-2-784-6027 FAX: +82-2-767-3677
SEIKO EPSON CORP. SEMICONDUCTOR OPERATIONS DIVISION IC Sales Dept. IC International Sales Group 421-8, Hino, Hino-shi, Tokyo 191-8501, JAPAN Phone: +81-42-587-5814 FAX: +81-42-587-5117
Document Code: 411806600 First Issue August 2009, JAPAN