sony cdx gt460us fm am
TRANSCRIPT
-
7/24/2019 Sony Cdx Gt460us Fm Am
1/46
SERVICE MANUAL
Sony CorporationeVehicle Division
Published by Sony Techno Create Corporation
US Model
Canadian Model
CDX-GT41UW/GT410U
E ModelCDX-GT460U/GT460US
Chinese ModelCDX-GT460U
9-887-470-032007C04-1
2007.03
Ver. 1.2 2007.03
SPECIFICATIONS
CD player section
Signal-to-noise ratio 120 dB
Frequency response 10 20,000 Hz
Wow and flutter Below measurable limit
Tuner sectionFM
Tuning range GT41UW/GT410U:
87.5 107.9 MHz
GT460U/GT460US:
87.5 108.0 MHz (at 50 kHz step)
87.5 107.9 MHz (at 200 kHz step)
FM tuning interval GT460U/GT460US:
50 kHz/200 kHz switchable
Antenna terminal External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity 9 dBf
Selectivity 75 dB at 400 kHzSignal-to-noise ratio 67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo), 0.3% (mono)
Separation 35 dB at 1 kHz
Frequency response 30 15,000 Hz
AM
Tuning range GT41UW/GT410U:
530 1,710 kHz
GT460U/GT460US:
531 1,602 kHz (at 9 kHz step)
530 1,710 kHz (at 10 kHz step)
AM tuning interval GT460U/GT460US:
9 kHz/10 kHz switchable
Antenna terminal External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity 30 V
USB player section
Interface USB (Full-speed)
Maximum current 500 mA
Power amplifier section
Outputs Speaker outputs (sure seal connectors)Speaker impedance 4 8 ohms
Maximum power output
52 W 4 (at 4 ohms)
The tuner and CD sections have no adjustments. Model Name Using Similar Mechanism NEW
CD Drive Mechanism Type MG-101U-188//Q
Optical Pick-up Name DAX-25A
Continued on next page
CDX-GT41UW/GT410U/GT460U/GT460US
FM/AM COMPACT DISC PLAYER
(Photo: CDX-GT460U)
AUDIO POWER SPECIFICATIONS (US MODEL)POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
-
7/24/2019 Sony Cdx Gt460us Fm Am
2/462
CDX-GT41UW/GT410U/GT460U/GT460US
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCKOR BASE UNITThe laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical pick-up block.
SERVICE NOTES
CAUTIONUse of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
GeneralOutputs Audio outputs terminal (sub/rear switchable)
Power antenna relay control terminal
Power amplifier control terminal
Inputs BUS control input terminal
BUS audio input terminal
Antenna input terminal
AUX input jack (stereo mini jack)
Tone controls Low: 10 dB at 60 Hz (XPLOD)
Mid: 10 dB at 1 kHz (XPLOD)
High: 10 dB at 10 kHz (XPLOD)
Power requirements 12 V DC car battery (negative ground)
Dimensions Approx. 178 50 179 mm
(71/82 71/8in.) (w/h/d)
Mounting dimensions Approx. 182 53 162 mm
(71/421/861/2in.) (w/h/d)
Mass Approx. 1.2 kg (2 lb. 11 oz.)
Supplied accessories Card remote commander: RM-X151
Parts for installation and connections (1 set)
USB cap
Design and specifications are subject to change without
notice.
US and foreign patents licensed from Dolby
Laboratories.
optical pick-up
semi-fixed resistor
Notes on Chip Component Replacement Never reuse a disconnected chip component.
Notice that the minus side of a tantalum capacitor may be damaged
by heat.
TEST DISCSPlease use the following test discs for the check on the CD section.
YDES-18 (Part No. 3-702-101-01)
PATD-012 (Part No. 4-225-203-01)
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK0
OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT!!
LES COMPOSANTS IDENTIFIS PAR UNE MARQUE0
SUR LESDIAGRAMMES SCHMATIQUES ET LA LISTE DES PICESSONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT.NE REMPLACER CES COMPOSANTS QUE PAR DES PICESSONY DONT LES NUMROS SONT DONNS DANS CE MANUELOU DANS LES SUPPLMENTS PUBLIS PAR SONY.
Ver. 1.1
-
7/24/2019 Sony Cdx Gt460us Fm Am
3/463
CDX-GT41UW/GT410U/GT460U/GT460US
UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARKUnleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SERVO BOARDCN2
MAIN BOARDCN350 J-2502-076-1
EXTENSION CABLE AND SERVICE POSITIONWhen repairing or servicing this set, connect the jig (extension cable)
as shown below.
Connect the MAIN board (CN350) and the SERVO board (CN2)
with the extension cable (Part No. J-2502-076-1).
This compact disc player is classified as a CLASS 1 LASER
product. The CLASS 1 LASER PRODUCT label is located on the
exterior.
E model
CD playbackYou can play CD-DA (also containing CD TEXT*), CD-R/CD-
RW (MP3/WMA/AAC files also containing Multi Session) and
ATRAC CD (ATRAC3 and ATRAC3plus format).
Type of discs Label on the disc
CD-DA
MP3
WMA
AAC
ATRAC CD
* A CD TEXT disc is a CD-DA that includes information such as
disc, artist and track name.
This label is located on the bottom of the chassis.
Chinese model
-
7/24/2019 Sony Cdx Gt460us Fm Am
4/464
CDX-GT41UW/GT410U/GT460U/GT460US
TABLE OF CONTENTS
1. GENERALLocation of Controls ........................................................ 5
Connections ..................................................................... 6
2. DISASSEMBLY2-1. Sub Panel (FL) Assy ........................................................ 11
2-2. CD Mechanism Block ..................................................... 11
2-3. Main Board ...................................................................... 12
2-4. Servo Board ..................................................................... 12
2-5. Chassis (T) Sub Assy....................................................... 13
2-6. Roller Arm Assy .............................................................. 13
2-7. Chassis (OP) Assy ........................................................... 14
3. DIAGNOSIS FUNCTION ........................................ 15
4. DIAGRAMS4-1. Block Diagram Main Section ...................................... 19
4-2. Block Diagram Display Section .................................. 20
4-3. Printed Wiring Board Main Section ............................ 224-4. Schematic Diagram Main Section (1/3) ...................... 23
4-5. Schematic Diagram Main Section (2/3) ...................... 24
4-6. Schematic Diagram Main Section (3/3) ...................... 25
4-7. Printed Wiring Board Key Section .............................. 26
4-8. Schematic Diagram Key Section ................................. 27
5. EXPLODED VIEWS5-1. Main Section.................................................................... 32
5-2. Front Panel Section ......................................................... 33
5-3. CD Mechanism Section (MG-101U-188//Q) .................. 34
6. ELECTRICAL PARTS LIST .................................. 35
NOTE FOR REPLACEMENT OF THE USB CONNECTOR
(CN902)To replace the USB connector requires alignment.
1. Insert the USB connector into the front panel.
2. Place the KEY board on the front panel and align the terminals
of the USB connector with the holes in the KEY board.
3. Solder the four terminals of the connector.
KEY board
front panel
USB (socket) connector
NOTE FOR REPLACEMENT OF THE SERVO BOARDWhen repairing, the complete SERVO board (A-1206-357-A) should
be replaced since any parts in the SERVO board cannot be repaired.
NOTE FOR THE 24-PIN CONNECTOR (CN901)Do not use alcohol to clean the 24-pin connector (CN901) connecting
the front panel with the main body.
Do not touch the connector directly with your bare hand. Poor contact
may be caused.
Ver. 1.2
-
7/24/2019 Sony Cdx Gt460us Fm Am
5/46
-
7/24/2019 Sony Cdx Gt460us Fm Am
6/466
CDX-GT41UW/GT410U/GT460U/GT460US
CONNECTIONS CDX-GT41UW/GT410U
A
B
AUDIO OUT REAR*
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
BUS CONTROL IN
Source selector*Slecteur de source*
XA-C40
*not supplied non fourni
*AUDIO OUT SUB/REAR
Exemple de raccordement
Remarques (2-A) Raccordez dabord le cble de mise la masse avant de
raccorder lamplificateur. Lalarme est mise uniquement lorsque lamplificateur intgr
est utilis.
Conseil (2-B- )Dans le cas du raccordement de deux changeurs de CD/MD ouplus, le slecteur de source XA-C40 (non fourni) est requis.
Connection example
Notes (2-A) Be sure to connect the ground (earth) lead before connecting
the amplifier.
The alarm will only sound if the built-in amplifier is used.Tip (2-B- )For connecting two or more CD/MD changers, the sourceselector XA-C40 (not supplied) is necessary.
-
7/24/2019 Sony Cdx Gt460us Fm Am
7/467
CDX-GT41UW/GT410U/GT460U/GT460US
L
R
BUS AUDIO IN
AUDIO OUT REAR*2
BUSCONTROL IN
2
4
5
1
3
AUDIO OUTREAR/SUB
BUSIN
AMP REM
Max. supply current 0.3 ACourant max. fourni 0,3 A
Fuse (10 A)Fusible (10 A)
Blue/white stripedRay bleu/blanc
ANT REM
RedRouge
YellowJaune
BlackNoir
BlueBleu
WhiteBlanc
GreenVert
PurpleViolet
White/black stripedRay blanc/noir
Gray/black stripedRay gris/noir
Green/black stripedRay vert/noir
GrayGris
Left
Gauche
RightDroit
LeftGauche
RightDroit
*1RCA pin cord (not supplied)*2 AUDIO OUT can be switched SUB or
REAR. For details, see the suppliedOperating Instructions.
*1Cordon broche RCA (non fourni)*2 AUDIO OUT peut tre commut sur SUB
ou REAR. Pour obtenir plus de dtails,reportez-vous au mode demploi fourni.
Purple/black stripedRay volet/noir
*1
Source selector(not supplied)
Slecteur de source(non fourni)
XA-C40
Supplied with the CD/MD changerFourni avec le changeur de CD/MD
Max. supply current 0.1 ACourant max. fourni 0,1 A
from car antenna (aerial) partir de lantenne du vhicule
Supplied with XA-C40Fourni avec le XA-C40
2
Schma de raccordement
1 un point mtallique de la voitureBranchez dabord le cble de mise la masse noir et,ensuite, les cbles dalimentation jaune et rouge.
2 Au cble de commande dantenne lectriqueou au cble dalimentation de lamplificateurdantenneRemarques Il nest pas ncessaire de raccorder ce cble sil ny a pas
dantenne lectrique ni damplificateur dantenne, ou avecune antenne tlescopique manuelle.
Si votre voiture est quipe dune antenne FM/AMintgre dans la vitre arrire/latrale, voir Remarquessur les cbles de commande et dalimentation .
3 Au niveau de AMP REMOTE IN delamplificateur de puissance en optionCe raccordement sapplique uniquement aux amplificateurs.Le branchement de tout autre systme risquedendommager lappareil.
4 la borne +12 V qui est alimente quand lacl de contact est sur la position accessoiresRemarques Sil ny a pas de position accessoires, raccordez la borne
dalimentation (batterie) +12 V qui est alimente enpermanence.Raccordez dabord le cble de mise la masse noir unpoint mtallique du vhicule.
Si votre voiture est quipe dune antenne FM/AMintgre dans la vitre arrire/latrale, voir Remarquessur les cbles de commande et dalimentation .
5 la borne +12 V qui est alimente enpermanenceRaccordez dabord le cble de mise la masse noir unpoint mtallique du vhicule.
Connection diagram
1 To a metal surface of the carFirst connect the black ground (earth) lead, then connect theyellow and red power supply leads.
2 To the power antenna (aerial) control lead orpower supply lead of antenna (aerial) boosterNotes It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with amanually-operated telescopic antenna (aerial).
When your car has a built-in FM/AM antenna (aerial) inthe rear/side glass, see Notes on the control and powersupply leads.
3 To AMP REMOTE IN of an optional poweramplifierThis connection is only for amplifiers. Connecting any othersystem may damage the unit.
4 To the +12 V power terminal which isenergized in the accessory position of theignition switchNotes If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.Be sure to connect the black ground (earth) lead to ametal surface of the car first.
When your car has a built-in FM/AM antenna (aerial) inthe rear/side glass, see Notes on the control and powersupply leads.
5 To the +12 V power terminal which is
energized at all timesBe sure to connect the black ground (earth) lead to a metalsurface of the car first.
Remarques sur les cbles de commande et dalimentation Le cble de commande dantenne lectrique (bleu) fournit une
alimentation de + 12 V CC lorsque vous mettez la radio soustension.
Lorsque votre voiture est quipe dune antenne FM/AMintgre dans la vitre arrire/latrale, raccordez le cble decommande dantenne (bleu) ou le cble dalimentation desaccessoires (rouge) la borne dalimentation de lamplificateurdantenne existant. Pour plus de dtail s, consultez votredtaillant.
Une antenne lectrique sans botier de relais ne peut pas treutilise avec cet appareil.
Raccordement pour la conservation de la mmoireLorsque le cble dalimentation jaune est raccord, le circuitde la mmoire est aliment en permanence mme si la cl decontact est sur la position darrt.
Remarques sur le raccordement des haut-parleurs Avant de raccorder les haut-parleurs, mettez lappareil hors
tension. Utilisez des haut-parleurs ayant une impdance de 4 8 ohms
avec une capacit lectrique adquate pour viter de lesendommager.
Ne raccordez pas les bornes du systme de haut-parleurs auchssis de la voiture et ne raccordez pas les bornes du haut-parleur droit celles du haut-parleur gauche.
Ne raccordez pas le cble de mise la masse de cet appareil la borne ngative () du haut-parleur.
Nessayez pas de raccorder les haut-parleurs en parallle. Raccordez uniquement des haut-parleurs passifs. Le
raccordement de haut-parleurs actifs (avec amplificateursintgrs) aux bornes des haut-parleurs peut endommagerlappareil.
Pour viter tout problme de fonctionnement, nutilisez pas lescbles des haut-parleurs intgrs installs dans votre voiture silappareil partage un cble ngatif commun () pour les haut-parleurs droit et gauche.
Ne raccordez pas entre eux les cordons des haut-parleurs delappareil.
Remarque sur le raccordementSi les haut-parleurs ne sont pas raccords correctement, lemessage FAILURE saffiche. Dans ce cas, assurez-vous queles haut-parleurs sont bien raccords.
Notes on the control and power supply leads The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner. When your car has built-in FM/AM antenna (aerial) in the rear/
side glass, connect the power antenna (aerial) control lead(blue) or the accessory power supply lead (red) to the powerterminal of the existing antenna (aerial) booster. For details,consult your dealer.
A power antenna (aerial) without a relay box cannot be usedwith this unit.
Memory hold connectionWhen the yellow power supply lead is connected, power willalways be supplied to the memory circuit even when the ignitionswitch is turned off.
Notes on speaker connection Before connecting the speakers, turn the unit off. Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage. Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of theleft speaker.
Do not connect the ground (earth) lead of this unit to thenegative () terminal of the speaker.
Do not attempt to connect the speakers in parallel. Connect only passive speakers. Connecting active speakers
(with built-in amplifiers) to the speaker terminals may damagethe unit.
To avoid a malfunction, do not use the built-in speaker leadsinstalled in your car if the unit shares a common negative ()lead for the right and left speakers.
Do not connect the units speaker leads to each other.
Note on connectionIf speaker and amplifier are not connected correctly, FAILUREappears in the display. In this case, make sure the speaker andamplifier are connected correctly.
-
7/24/2019 Sony Cdx Gt460us Fm Am
8/468
CDX-GT41UW/GT410U/GT460U/GT460US
CDX-GT460U/GT460US
AUDIO OUT REAR*
BUS AUDIO IN
BUS CONTROL IN
A
B
BUS AUDIO IN
BUS CONTROL IN
Source selector*Selector de fuente*
*
XA-C40
*not suppliedno suministrado
*AUDIO OUT SUB/REAR
Connection example
Notes (2-A) Be sure to connect the ground (earth) lead before connecting
the amplifier. The alarm will only sound if the built-in amplifier is used.
Tip (2-B- )For connecting two or more CD/MD changers, the sourceselector XA-C40 (not supp lied) is necessary.
Ejemplo de conexiones
Notas (2-A) Asegrese de conectar primero el cable de conexin a masa
antes de realizar la conexin del amplificador. La alarma sonar nicamente si se utiliza el amplificador
incorporado.
Sugerencia (2-B- )Si desea conectar dos o ms cambiadores de CD/MD,necesitar el selector de fuente XA-C40 (no suministrado).
-
7/24/2019 Sony Cdx Gt460us Fm Am
9/469
CDX-GT41UW/GT410U/GT460U/GT460US
L
R
BUS AUDIO IN
AUDIO OUT REAR*2
BUSCONTROL IN
2
4
5
1
3
AUDIO OUTREAR/SUB
BUSINfrom car antenna (aerial)
desde la antena del automvil
*1RCA pin cord (not supplied)*2AUDIO OUT can be switched SUB or
REAR. For details, see the suppliedOperating Instructions.
*1Cable con terminales RCA(no suministrado)
*2AUDIO OUT (Salida de audio) puedecambiarse a SUB (Secundaria) o REAR(Posterior). Para obtener informacin,consulte el manual de instruccionessuministrado.
*1
*2
AMP REM
Max. supply current 0.3 ACorriente mx. de alimentacin de 0,3 A
Fuse (10 A)Fusible (10 A)
Blue/white stripedCon rayas azules y blancas
RedRojo
YellowAmarillo
WhiteBlanco
GreenVerde
PurpleMorado
White/black striped
Con rayas blancas y negras
Grey/black stripedCon rayas grises y negras
Green/black stripedCon rayas verdes y negras
GreyGris
LeftIzquierdo
RightDerecho
LeftIzquierdo
RightDerecho
ANT REM
BlackNegro
BlueAzul
Max. supply current 0.1 ACorriente mx. de alimentacin de 0,1 A
Purple/black stripedCon rayas moradas y negras
Source selector(not supplied)
Selector de fuente(no suministrado)
XA-C40
Supplied with the CD/MD changerSuministrado con el cambiador de CD/MD
*1
Supplied with XA-C40Suministrado con el XA-C40
2
Connection diagram1 To a metal surface of the car
First connect the black ground (earth) lead, then connect theyellow and red power supply leads.
2 To the power antenna (aerial) control lead orpower supply lead of antenna (aerial) boosterNotes It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with amanually-operated telescopic antenna (aerial).
When your car has a built-in FM/AM antenna (aerial) inthe rear/side glass, see Notes on the control and powersupply leads.
3 To AMP REMOTE IN of an optional poweramplifierThis connection is only for amplifiers. Connecting any othersystem may damage the unit.
4 To the +12 V power terminal which isenergized in the accessory position of theignition switchNotes If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.Be sure to connect the black ground (earth) lead to ametal surface of the car first.
When your car has a built-in FM/AM antenna (aerial) inthe rear/side glass, see Notes on the control and powersupply leads.
5 To the +12 V power terminal which isenergized at all timesBe sure to connect the black ground (earth) lead to a metalsurface of the car first.
Notes on the control and power supply leads The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner. When your car has built-in FM/AM antenna (aerial) in the rear/
side glass, connect the power antenna (aerial) control lead(blue) or the accessory power supply lead (red) to the powerterminal of the existing antenna (aerial) booster. For details,consult your dealer.
A power antenna (aerial) without a relay box cannot be usedwith this unit.
Memory hold connectionWhen the yellow power supply lead is connected, power willalways be supplied to the memory circuit even when the ignitionswitch is turned off.
Notes on speaker connection Before connecting the speakers, turn the unit off. Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage. Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of theleft speaker.
Do not connect the ground (earth) lead of this unit to thenegative () terminal of the speaker.
Do not attempt to connect the speakers in parallel. Connect only passive speakers. Connecting active speakers
(with built-in amplifiers) to the speaker terminals may damagethe unit.
To avoid a malfunction, do not use the built-in speaker leadsinstalled in your car if the unit shares a common negative ()lead for the right and left speakers.
Do not connect the units speaker leads to each other.
Note on connectionIf speaker and amplifier are not connected correctly, FAILUREappears in the display. In this case, make sure the speaker andamplifier are connected correctly.
Diagrama de conexin1 A una superficie metlica del automvil
Conecte primero el cable de conexin a masa negro, ydespus los cables amarillo y rojo de fuente de alimentacin.
2 Al cable de control de la antena motorizadao al cable de fuente de alimentacin delamplificador de seal de la antenaNotas Si no se dispone de antena motorizada ni de amplificador
de antena, o se utiliza una antena telescpica accionadamanualmente, no ser necesario conectar este cable.
Si el automvil incorpora una antena de FM/AM en elcristal trasero o lateral, consulte Notas sobre los cablesde control y de fuente de alimentacin.
3 A AMP REMOTE IN de un amplificador depotencia opcionalEsta conexin es slo para amplificadores. La conexin decualquier otro sistema puede daar la unidad.
4 Al terminal de alimentacin de +12 V querecibe energa en la posicin de accesoriodel interruptor de encendidoNotas Si no hay posicin de accesorio, conctelo al terminal de
alimentacin (batera) de +12 V que recibe energa sininterrupcin.Asegrese de conectar primero el cable de conexin amasa negro a una superficie metlica del automvil.
Si el automvil incorpora una antena de FM/AM en elcristal trasero o lateral, consulte Notas sobre los cables
de control y de fuente de alimentacin.
5 Al terminal de alimentacin de +12 V querecibe energa sin interrupcinAsegrese de conectar primero el cable de conexin a masanegro a una superficie metlica del automvil.
Notas sobre los cables de control y de fuente dealimentacin El cable de control de la antena motorizada (azul) suministrar
cc de + 12 V cuando conecte la alimentacin del sintonizador. Si el automvil dispone de una antena de FM/AM incorporada
en el cristal trasero o lateral, conecte el cable de control deantena motorizada (azul) o el cable de fuente de alimentacinauxiliar (rojo) al terminal de alimentacin del amplificador deantena existente. Para obtener ms informacin, consulte a sudistribuidor.
Con esta unidad no es posible utilizar una antena motorizadasin caja de rel.
Conexin para proteccin de la memoriaSi conecta el cable de fuente de alimentacin amarillo, el circuitode la memoria recibir siempre alimentacin, aunque apague elinterruptor de encendido.
Notas sobre la conexin de los altavoces Antes de conectar los altavoces, desconecte la alimentacin
de la unidad. Utilice altavoces con una impedancia de 4 a 8 con la
capacidad de potencia adecuada para evitar que se daen. No conecte los terminales de altavoz al chasis del automvil,
ni conecte los terminales del altavoz derecho con los delizquierdo.
No conecte el cable de conexin a masa de esta unidad alterminal negativo () del altavoz.
No intente conectar los altavoces en paralelo. Conecte solamente altavoces pasivos. Si conecta altavocesactivos (con amplificadores incorporados) a los terminales dealtavoz, puede daar la unidad.
Para evitar fallas de funcionamiento, no utilice los cables dealtavoz incorporados instalados en el automvil si la unidadcomparte un cable negativo comn () para los altavocesderecho e izquierdo.
No conecte los cables de altavoz de la unidad entre s.
Nota sobre la conexinSi el altavoz no est conectado correctamente, aparecerFAILURE en la pantalla. Si es as, compruebe la conexin delaltavoz.
-
7/24/2019 Sony Cdx Gt460us Fm Am
10/4610
CDX-GT41UW/GT410U/GT460U/GT460US
SECTION 2
DISASSEMBLY
Note:This set can be disassemble according to the following sequence.
2-1. SUB PANEL (FL-U) ASSY
(Page 11)
2-2. CD MECHANISM BLOCK(Page 11)
SET
2-3. MAIN BOARD(Page 12)
2-5. CHASSIS (T) SUB ASSY(Page 13)
2-6. ROLLER ARM ASSY(Page 13)
2-7. CHASSIS (OP) ASSY(Page 14)
2-4. SERVO BOARD(Page 12)
1. CHUCKING ARM SUB ASSY(SUPPLEMENT-1 Page 1)
2. SLED MOTOR ASSY(SUPPLEMENT-1 Page 2)
3. OPTICAL PICK-UP SECTION(SUPPLEMENT-1 Page 3)
4. OPTICAL PICK-UP(SUPPLEMENT-1 Page 3)
Ver. 1.2
-
7/24/2019 Sony Cdx Gt460us Fm Am
11/4611
CDX-GT41UW/GT410U/GT460U/GT460US
2-2. CD MECHANISM BLOCK
Note:Follow the disassembly procedure in the numerical order given.
2-1. SUB PANEL (FL) ASSY
2 two claws
3 two claws
4sub panel (FL-U) assy
1two screws (+PTT 2.66)
4 CN350
5 CN352 (3P)
3
1 screw(+PTT 2.66)
2 screw(+PTT 2.66)
6 two screws(+PTT 2.64)
7 bracket (CD)8 CD mechanism block
-
7/24/2019 Sony Cdx Gt460us Fm Am
12/4612
CDX-GT41UW/GT410U/GT460U/GT460US
2-4. SERVO BOARD
2-3. MAIN BOARD
0 MAIN board
insulating sheet3
2 two screws(+PTT 2.68)
8 screw(+PTT 2.610)
7 screw(+P 2.610)
9 heat sink
5 two screws(+P 2.68)
4 two screws(+PTT 2.610)
6 two screws(+PTT 2.610)
1 three screws(+BTT 2.65)
5 SERVO board
SERVO board
claw
claw
3 toothed lock screw(M 1.72.5)
2 toothed lock screw(M 1.72.5)
1 Remove the eleven solders.
GRYYELBLU
ORGREDBLK
REDWHT
BLKRED
WHT
4 optical pick-up (16 core)(CN1)
-
7/24/2019 Sony Cdx Gt460us Fm Am
13/4613
CDX-GT41UW/GT410U/GT460U/GT460US
2-6. ROLLER ARM ASSY
2-5. CHASSIS (T) SUB ASSY
4 chassis (T) sub assy
3 claw
1 two precision screws(+P 1.72.2)
2 two precision screws(+P 1.72.2)
3 washer
4 gear (RA1)
5 roller arm assy
1 spring (RAL)
2 spring (RAR)
-
7/24/2019 Sony Cdx Gt460us Fm Am
14/4614
CDX-GT41UW/GT410U/GT460U/GT460US
2-7. CHASSIS (OP) ASSY
Ver. 1.2
7 coil spring (damper) (natural)
8 coil spring (damper) (green)
6chassis (OP) assy
5
1 tension spring (KF)
2 gear (LE1)
3 lever (D)
4 slider (R)
-
7/24/2019 Sony Cdx Gt460us Fm Am
15/4615
CDX-GT41UW/GT410U/GT460U/GT460US
SECTION 3DIAGNOSIS FUNCTION
Description of the Diagnostics function:
1. Setting the Diag display modeWith the power off, press the [4]button, [5]button, and [4]button
on the set body or the remote control (for more than 2 seconds)
in turn.
2. Canceling the Diag display modeDuring the Diag function mode, press the [OFF]button.
3. Initial display in the Diag display mode.Just when the Diag mode is entered, reset count is displayed.
The display mode is switched by each rotation of
SEEK +/M> or SEEK /.m keys.
4. Contents of each display mode4-1. Reset count display mode
4-2. Reset count by watchdog timer display mode
4-3. Number of connected units display mode
The display mode is switched by each rotation of [2/GP/ALBM+]or
[1/GP/ALBM--]keys during the number of connected units displaymode.
4-4. Operating hours display mode
Reset count
(in hexadecimal format)Diag code01: Reset count
0 1 X X
Reset count(in hexadecimal format)
Diag code02: Number of resets by watchdog timer
0 2 X X
Show the number of connected units forCD-C, MD-C and XM respectively fromthe rightmost (in hexadecimal format).
Recency of information1-3: 1 represents the latest.
Diag code03: Number of connected unit.
0 3 1 X X X
No. of connected units history 1 (latest) display
No. of connected units history 3 display
No. of connected units history 2 display
0 3 1 X X X
0 3 2 X X X
0 3 3 X X X
Operating hours
(in hexadecimal format)Diag code04: Operating hours
0 4 X X X X
Reset count display
OFFSET/FAILURE error display
CD error information display
Operating hours display
Number of connected units display
Reset count by watchdog timer display
0 1 X X
0 2 X X
0 3 1 X X X
0 4 X X X X
0 5 1 X X
0 6 1 X X X X X
USB error information display
0 7 1 X X
-
7/24/2019 Sony Cdx Gt460us Fm Am
16/4616
CDX-GT41UW/GT410U/GT460U/GT460US
4-5. CD error information display mode4-5-1. Error description
4-5-2. Disc type and operating hours
The display mode is switched by each rotation of [2/GP/ALBM+]or
[1/GP/ALBM--]keys during the CD error information display mode.
4-6. OFFSET/FAILURE error display mode
The display mode is switched by each rotation of [2/GP/ALBM+]or
[1/GP/ALBM--] keys during the OFFSET/FAILURE error display
mode.
Error description(in hexadecimalformat)
Recency of information1-3: 1 represents the latest.
Diag code05: CD error information
0 5 1 X X
Operating hours
Recency of information1-3: 1 represents the latest.
Diag code05: CD error information
0 5 1 X X X X
CD error info history 1 (latest)Error description plus error details display
CD error info history 3
Disc type plus operating hours display
CD error info history 3Error description plus error details display
CD error info history 2Disc type plus operating hours display
CD error info history 2Error description plus error details display
CD error info history 1 (latest)Disc type plus operating hours display
0 5 1 X X X X
0 5 2 X X
0 5 2 X X X X
0 5 3 X X
0 5 3 X X X X
0 5 1 X X
Operating hours
Recency of information1-3: 1 represents the latest.
Diag code06: OFFSET/FAILURE
Error description
(0: OFFSET, 1: FAILURE)
0 6 1 X X X X X
OFFSET/FAILURE error history 1 (latest) display
OFFSET/FAILURE error history 3 display
OFFSET/FAILURE error history 2 display
0 6 2 X X X X X
0 6 3 X X X X X
0 6 1 X X X X X
Error information
Indication Description
1X SERVO ERROR3X LOADING ERROR
4X TRACK JUMP
5X TEXT ERROR
FX MECHA ERROR
Disc type
Indication Disc type
0 MP3
1 WMA
2 AAC
3 ATRAC
8 CD/DA
F UNKNOWN
4-7. USB error information display mode4-7-1. Error description
Error description(in hexadecimalformat)
Recency of information1-5: 1 represents the latest.
Diag code07: USB error information
0 7 1 X X
Error information
Indication Description
15 DEVICE ERROR
17FILE ERROR
(NO MUSIC)
1E POWER ON ERROR
1F BOOT ERROR
3A INVALID EJECTERROR
43 READ ERROR
44INVALID
FORMAT FILE
FANOT SUPPORT
DEVICE
FBHUB NOT
SUPPORT
-
7/24/2019 Sony Cdx Gt460us Fm Am
17/4617
CDX-GT41UW/GT410U/GT460U/GT460US
4-7-2. Disc type and operating hours The display mode is switched by each rotation of [2/GP/ALBM+]or[1/GP/ALBM--]keys during the CD error information display mode.
USB error info history 1 (latest)Error description plus error details display
USB error info history 3Disc type plus operating hours display
USB error info history 3Error description plus error details display
USB error info history 2Disc type plus operating hours display
USB error info history 2Error description plus error details display
USB error info history 1 (latest)Disc type plus operating hours display
0 7 1 X X X X X
0 7 2 X X
0 7 2 X X X X
0 7 3 X X
0 7 3 X X X X X
0 7 1 X X
USB error info history 5Disc type plus operating hours display
USB error info history 5Error description plus error details display
USB error info history 4Disc type plus operating hours display
USB error info history 4Error description plus error details display
0 7 4 X X
0 7 4 X X X X
0 7 5 X X
0 7 5 X X X X
Operating hours
Recency of information1-5: 1 represents the latest.
Diag code07: USB error information
0 7 1 X X X X
-
7/24/2019 Sony Cdx Gt460us Fm Am
18/4618
CDX-GT41UW/GT410U/GT460U/GT460US
MEMO
-
7/24/2019 Sony Cdx Gt460us Fm Am
19/46
-
7/24/2019 Sony Cdx Gt460us Fm Am
20/46
-
7/24/2019 Sony Cdx Gt460us Fm Am
21/46
21 21CDX-GT41UW/GT410U/GT460U/GT460US
CDX-GT41UW/GT410U/GT460U/GT460US
Waveforms
MAIN Board
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRINGBOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note isprinted in each block.)
For schematic diagrams.Note: All capacitors are inF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolyticsand tantalums.
All resistors are inand 1/4W or less unless otherwise
specified. f : internal component.C : panel designation.
For printed wiring boards.Note:X : parts extracted from the component side.Y : parts extracted from the conductor side. a : Through hole.
: Pattern from the side which enables seeing.(The other layers' patterns are not indicated.)
A : B+ Line.B : B Line.H : adjustment for repair. Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions. no mark : FM
( ) : AM< > : CD PLAY
: Impossible to measure Voltages are taken with a VOM (Input impedance 10 M).
Voltage variations may be noted due to normal productiontolerances.
Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal productiontolerances.
Circled numbers refer to waveforms. Signal path.
J : CD PLAYF : FMf : AML : AUX
Caution:Pattern face side: Parts on the pattern face side seen from the(Side B ) pat te rn face a re ind icated .
Parts face side: Parts on the parts face side seen from the( Si de A) p art s f ac e a re in di ca te d.
Q
C
These are omitted
EB
E
These are omitted
CB
C
These are omitted
BE
0.8 Vp-p
32.768 kHz
1 IC501 i;(XOUT)
1 Vp-p
18.432 MHz
2 IC501 is(OSC IN)
0.2 V/DIV, 20sec/DIV
0.5 V/DIV, 0.1sec/DIV
Note:The components identi-fied by mark0or dottedline with mark0are criti-
cal for safety.Replace only with part
number specified.
Note:Les composants identifis parune marque 0sont critiquespour la scurit.
Ne les remplacer que par unepice portant le numrospcifi.
-
7/24/2019 Sony Cdx Gt460us Fm Am
22/46
2222CDX-GT41UW/GT410U/GT460U/GT460US
CDX-GT41UW/GT410U/GT460U/GT460US
: Uses unleaded solder.4-3. PRINTED WIRING BOARD MAIN SECTION
1
A
B
C
D
E
F
G
H
I
J
2 3 4 5 6 7 8 9 10 11 12 13 14
L RJ1
(ANTENNA) L R
J652
-1 -2 -3 -4
AUDIO OUTREAR/SUB
BUSAUDIO IN
CN2
CN101
CDMECHANISM
UNIT(MG-101U)
1
3
S501
9K
10K
FREQUENCYSELECT
1
4
8 7
3 2 1
6 5 4
3
4
2
1
1
5
1
7
1
5
X501 S103
RESET
1-872-031- 11
R552
JC38
C890
D153
C951C
820
C704
C705
R673
D503
JC905
IC802
R672
C302
R553JC912
IC401
D802
R815
R814
R813 D801
R816
R818
R890
C812 R8
19
R8
20
Q805C8
14
C808
IC804
R891
JC810
C807
C445
R812
R811
C805
R810
IC681
C804
R809
C802R529
C810
Q3
R351
R570
JC907
L402
L411
JC909
JC910
JC927
JC924
R903
JC923
JC922
JC929
R612R615
R912
C317
JC931
JC930JC928
C7
R917
D105
C329
D107
D106
JC21
D111
D112
JC921
R152
D109
R606
D108
R607
D113
JC926
JC939
C509
JC940R920
R817
JC943
C703
C313
R923
C315
R925
R924
R709
D703
D702
R706
Q702
R708
R
707
D605
D606
D603
D602
R611
L409
R616
JC22
C601
R601
R602
C402
R402
R401
L410
C418
C419
L406
L401
C307
IC6 02
C305
C309
L403
C417
IC601
C415
L405
JC19
R901
R902
JC906
JC941
C301
C325
C516
C330
C304
JC933
C515
JC36
R537
R551
R507
GT460U/GT460U S
GT460U/GT460US
GT460U/GT460U S
GT460U/GT460US
GT41UW/GT410U
GT41UW/GT410U
R538
R523
R534
R557
R544
R556
R545
R546
R559
R520
JC811
JC934
IC801
C702
JC938
JC935
R511
JC33
JC32
R555
R568
C507
C508
C320
R910
C504
R521
R522
C513
C501
C512 C514
R504
R505
R502
R503
C502
R671
R565
R567
R561
L4
R517
Q664
JC16
C510
R519
D502
R674
R563
C519
R569
R636
JC18
JC24
D353R600
D901
JC23
JC903
C312
JC920
JC904
R61
C681
Q420
Q440
C412
C682
D604
D2
Q605
R531
Q491
Q492
R604
R491
JC902
D491
R603
R2
R3R4 R5
R10
C3
C15
C6
L1
R12
R13R6
R7
C8
JC5
D110
CN352
R151
R154
R155
JC932
R153
L151
L901
L902
JC17
R533R532
L407
JC901
JC936
JC913
JC914
R509
JC942
R919
R918
JC12
C816
R558
JC28
C361
C362
C413C414
R357
R358
R355R356
R420
R440
R460
R470
R452
R430
R485
C484 R
451
R431
JC4
JC30
JC29
C443
C426C423
Q432
Q452
C454
C318
R301
JC8
JC14
JC31
R 4 50 R 4 49
C432 C452
R448 R447
R442
R421
R471
R461
Q460
Q470
C434
R462
R472C463
C462
C472 C473
JC9
C444
C424
R540
R510
R526
JC1
R951
R952
C319
R961
R302
C157
D102
D101D
104
D103
C905
C891
C892
C921
C924
JC911
R150
R354
JC11
L501
R913
IC501
R802
R803
R591
L804
L805
R592 R
593
Q401
Q402
JC401
Q411
Q412R411
R493
R916
R915
R914
R403
R404
D152
D151
(CHASSIS)
R926
R927
R536
R550
R595
R596
R597
R598
R599
R156
R157
R158
D156
JC10
R800
C706
C707
D706
D707
JC705
C158
C159
C953
C493
C494
TU1
(TUNER UNIT)
JW1
JW2
JW22
JW23
JW24
JW28
JW34
JW35
JW38
JW42
JW43
JW44
JW45
JW46
JW49
JW50
YEL
JW51
JW52
JW53
JW56
JW57
JW58
JW59
JW60
JW61
JW66
JW68
JW74
JW75
JW76
JW77
JW79
JW95
JW96
JW97
JW98
JW99
JW101
JW102
JW103
JW105
JW106
JW26
JW25
JW33
JW32
JW31
JW36
JW29
JW81
JW80
JW19
JW20
JW21
JW12
JW11
JW10
JW9
JW109
JW108
JW100
JW110
JW17
JW16
JW15
JW14
JW13
JW92
JW91
JW89
JW86
JW83
JW62
JW64
JW63
JW65
JW69
JW84
JW67
JW48
JW47
JW27
JW3
JW4
JW30
JW70
JW71
JW72
JW73
JW78
JW82
JW85
JW87
JW88
JW90
JW104
JW111
JW113
JW114
JW115
JW116
JW119
JW120JW121
JW122
JW123
JW124
JW125
JW126
JW127
JW128
JW129
JW130
JW131
JW132
JW133
JW134
JW135
JW136
JW137
JW138
D607
S103
C803
D304
D303
D308
C623
D30
7
C622
C683
D311
D312
L818
D310
C316
C314
R705
D301
C809
IC803
D302
C403
C401
C701
YEL
C308
C306
C405
C409
C806
C811X50
1
CN350
D309D30
6
D30
5
TH400
X502
L300
L802
L803
C491
CN300
C2
C5
C153
C152
C151
C818
CN370
C364
C363
C365
C366
C486
C485
C431
C451
C461C471
C441
C421
C303
C801
JW18
JW54
JW55
JW118
D804
JW139
C624
C625
C626
C815
JW107
JW5
JW117
JW112
JW94
JW93
CNJ400
CNJ400(BUS CONTROL IN)
IC300
C406
C407
JW140
JW41
JW40
JW39
C819
C600
JW7
F901
R710
CN351
R9
(Page 26)
D2 E-2
D101 I-4
D102 I-4
D103 I-4
D104 I-4
D105 J-7
D106 I-4
D107 I-4
D108 I-3
D109 I-2
D110 I-4
D111 I-4
D112 I-4D113 H-3
D151 I-2
D152 I-2
D153 I-3
D156 I-2
D301 C-8
D302 D-8
D303 C-9
D304 D-9
D305 C-6
D306 C-6
D307 C-6
D308 C-6
D309 C-6
D310 C-6
D311 C-7
D312 C-7
D353 H-8
D491 E-5
D502 H-7
D503 I-6
D602 D-10
D603 D-10
D 60 4 E- 10
D605 D-9
D606 D-9
Semiconductor LocationRef . No. Locat ion Ref . No. Locat ion
D607 D-9
D702 C-8
D703 C-9
D706 C-9
D707 D-8
D 801 F-10
D802 F-9
D804 H-9
D 901 B-10
I C3 00 B -6
I C4 01 D -3
I C5 01 G -6I C6 01 E -1 0
I C6 02 G -7
I C6 81 D -6
I C8 01 I -1 0
I C8 02 H -1 0
I C8 03 G -1 0
I C8 04 H -9
Q3 F-2
Q401 F-4
Q402 E-4
Q411 E-5
Q412 E-4
Q420 B-4
Q432 B-3
Q440 B-4
Q452 C -3
Q460 C -4
Q470 C -4
Q491 E-5
Q492 E-5
Q 60 5 D -1 0
Q664 I-6
Q702 C -8
Q 80 5 G -11
-
7/24/2019 Sony Cdx Gt460us Fm Am
23/46
23 23 CDX-GT41UW/GT410U/GT460U/GT460US
CDX-GT41UW/GT410U/GT460U/GT460US
4-4. SCHEMATIC DIAGRAM MAIN SECTION (1/3) Refer to page 28 for IC Block Diagrams.
IC B/D
IC B/D
C701
C303
C600
D606
C622
C306
R301
R302
C623
R604 R603
R706 R708
Q492
C491
R491
R600
R531
JC36
JC905
C626
C625
C624
R599
Q491
C601
JC909
C 70 2 C 70 3
C705
C704
L300
C319 C318
C317
C325
C301
C302
C444 C424 C330
C304
C454 C434
C3 05 C3 07
C309
JC939
JC940
R615
JC31JC30JC29
L902
L901C308
JC12
C312
C320
C314
C313
C316
C315
C681C682C683
IC681IC602
R961
R493 JC8
JC1
R705
R709
R707
R612
R607
R606
JC21
JC 22 R 611
R616 R602
R601
IC300
IC601
JC33 JC32
F901
Q702
Q605
CNJ400
TH400
JC910
JC19
D302
D301
D304
D303D305D306D307D308D309D310D311D312
C706
C707
JC705
CN300
D706
D703
D607
D702
D707
D603 D602
D 60 5 D 604D901
D491
R710
C329
(Page 25)
(Page 24)
-
7/24/2019 Sony Cdx Gt460us Fm Am
24/46
2424CDX-GT41UW/GT410U/GT460U/GT460US
CDX-GT41UW/GT410U/GT460U/GT460US
4-5. SCHEMATIC DIAGRAM MAIN SECTION (2/3) Refer to page 28 for IC Block Diagrams.
(Page 23)
(Page 25)
IC B/D
R442R421 R451 R431
C441C421 C451 C431
R10
Q440Q420 Q452 Q432
R447R448 R449 R450
R12 R13
R430
R420
R460
R470
R440
R452
R 35 7 R 35 8
R 35 5 R 3 56
C365
C366
C461
R461
C471
R471
R462R472
C485
R153R155
L1
JC9
JC28
R918
R919
C953
R150
C406
C407
Q401
Q402
Q411
Q460Q470
Q412
C426 C423
C 4 45 C 4 43
C 4 73 C 4 72
C484
JC4
C463 C462
C452 C 432 C413 C414
C905
C362
C361
JC943
C6
C3
C8
C157
JC926
L818
C921
CN352
L805
R152
R151
L151
JC927
C924
JC923
L804
C818
JC928JC930
JC929JC931
R913
J1
R5
R4
R2
R3
C15
JC5
JC11
R354
R920
JC401
R411
R156
R158
R157
R485
J C9 42 J C9 41
C7
R 6 R 7
L4
R558
R61
C151
C153
C152
R154
C820
R912
JC920
J C9 21 J C9 22
R952
R951
JC924
CN370
J652TU1
Q3
C486
IC401
C2
C364
C363
R403
R404
C158
C159
C493
C494
D106
D107
D109
D108
D113
D111
D112
D110
D105
D153
D104
D103
D102
D101
D151
D152D156
C5
D2
R9
JC10
(Page 27)
-
7/24/2019 Sony Cdx Gt460us Fm Am
25/46
25 25 CDX-GT41UW/GT410U/GT460U/GT460US
CDX-GT41UW/GT410U/GT460U/GT460US
4-6. SCHEMATIC DIAGRAM MAIN SECTION (3/3)
Refer to page 21 for Waveforms. Refer to page 29 for IC Block Diagrams. Refer to page 30 for IC Pin Description of IC501.
(Page 23) (Page 24)
IC B/D IC B/D
IC B/D
X502
C409
R351
R502
R401
R402 L401
L410
L403
L407
R551
R557
R511
R510
R532
R534
R553
R567R565
R561
R503
D353
R540
R555
R520
R523
L501
L803
R813
L802
C803 C806
Q805
R811
R812R810
R809
R816
R817
JC901 R901
L411
R925
C891
R552
R591
R592
R593
R927
R595
CN350
R507
R545
S501
JC902
JC903
C415
L406
L405
C892
C804
C402
C419
C412
C507
C508
C510
JC14
C519
C512
C501
C513
R672
JC913
R526
R556
R559 C504R916
R914
R915
R544
JC911
R671
C516C515R521
R522
J C9 32 J C9 33
JC934
R517
JC935
JC936
JC938
JC23
R673
C502
C514 JC16
R 50 5 R 50 4
R596
R598
JC24
JC914
R570
R529
JC912
C509
R674
R519
JC17
R536
JC38
R546
R 8 02 R 8 03
JC811
C815C816
R891
R819R820
C814
R818
C812
JC810
R890
C810
C811
C890
R815R800
JC907R814
C808
C809
C807
C805
IC802IC801
C802C801
R917
R926
CN351
JC18
R636
R563
R 9 23 R 9 24
R533
L402 L409
C418
C401
JC906JC904
R902
R903
C417C405
IC803
R910
R509
X501
S103
Q664
C403
R568
D502
C951
D804
C819
IC804
D802
D801
IC501
R597
D503
R569
R550
R537
R538
-
7/24/2019 Sony Cdx Gt460us Fm Am
26/46
2626CDX-GT41UW/GT410U/GT460U/GT460US
CDX-GT41UW/GT410U/GT460U/GT460US
4-7. PRINTED WIRING BOARD KEY SECTION : Uses unleaded solder.
1
A
B
C
D
E
F
G
H
I
J
2 3 4 5 6 7 8 9 10 11 12 13
1-872-032-
1-872-032- (11)
11
1-872-033- (11)
11
1-872-033- (11)
11
(11)
11
LED846,946,S903
SOURCE
M >
SEEK+
LSW901LED861864,LED961963
(RING ILLUMINATION)
LED843,943,S902
SEEK
LSW902
OFF
LED844,944,S904
EQ3
LED845,945,S906
BTM/CAT
1/GP/ALBM 2/GP/ALBM+ 5 6/PAUSE SCRL
PUSH SELECT
(VOLUME)
RE901
AUX
J901
DSPL/DIM
IC971
MODE
LED 847,947,S907
LED 850,950,S908
LED 851,951,S909
LED852,952,S910
LED 853,953,S911
LED854,954,S912
LED855,955,S913
LED 856,956,S914
LED857,957,S915
3/REP 4/SHUF
LED841,941,S901
A
MAIN BOARD CN370
1 2
5 4 3
LED 842,942(CD INDICATOR)
LED944
LED943LED843
LED863
LED961
LED862
LED864
LED846
LED946
LED847
R904
LED947
LED842
LED942
LED850
LED950
LED851L
ED951
LED852
LED845
LED952
S908 S909
S903
S902
LED853L
ED953
LED854
S907
LED945
LED856
LED956
LED857
LED957
LED941LED841
R909
LED861
LED963
LED962
IC971
S906
S904
S910
R854
R954
R947
R847
R961
R861
R862
R843
R943
R906
R907
R908
R902
R903
C974R977
R853
R953
LSW902
S915
LSW901
LED844
S901
S911 S912 S913 S914
LED954
LED855
LED955
1
2
3
4
CN902
ORG
REDFB901
FB903
FB902
BRN
ORG
RED
BRN
R989
C981
R988
C982R901
C992
C975
D906 D953D
904
D903
R971
R888
R889
R887
C976
R978
R984
R983
C979
R850
R950
R910
CN901
Q882Q881 Q883
R911
FB907
FB906C991
R849
R949
R951
R851
R912
R952
R852
R914
R915
R962
R848
R948R946
R846
R845
R945
R944
R844
R905
D971 R976
R975
R864R 863
Q991 Q992
R922
R921
D907
R913
C977
R982
R942 R842
R841
R941
R981
D905
D908 FB904FB905
R993
R994R995
LF901
D951
D955
R881 R882
R886
R883
R885R884IC972
C905
RB901
FL901FLUORESCENT INDICATOR TUBE
CN902
RE901
(Page 22)
LE D844 B -2LE D845 C-2LE D846 B -4LE D847 C-4LE D850 D-5LE D851 D-6LE D852 D-7LE D853 D-8LE D854 D-8LE D855 D-9L ED 85 6 D -1 0L ED 85 7 D -11LE D861 B -3LE D862 B -2
Ref. No. Location
D903 I-10D904 I-9D905 I-10D906 I-10D907 I-10D908 H-9D971 H-4
IC971 D-4IC972 I-11
L ED 84 1 A -13LE D842 B -7LE D843 A -1
Semiconductor LocationRef. No. Location
LE D863 B-3LE D864 C-3L ED 94 1 A -1 3LE D942 B-7LE D943 A-2LE D944 B-2LE D945 C-2LE D946 B-4LE D947 C-4LE D950 D-5LE D951 D-6LE D952 D-7LE D953 D-7LE D954 D-8
Ref . No. Locat ion Ref . No. Locat ion
LE D955 D-9LE D9 56 D -10LE D9 57 D -11LE D961 B -3LE D962 C-3LE D963 C-2
Q881 I-8Q882 I-8Q883 I-9Q991 I-6Q992 I-6
-
7/24/2019 Sony Cdx Gt460us Fm Am
27/46
27 27 CDX-GT41UW/GT410U/GT460U/GT460US
CDX-GT41UW/GT410U/GT460U/GT460US
4-8. SCHEMATIC DIAGRAM KEY SECTION
R989
R988
R901 R904
R978
R984R983
R909
R850R950
R910
Q882
Q881
Q883
R911
R849R949
R 95 1 R 85 1
R912
R 95 2 R 85 2
R 91 4 R 91 5
R954
R962
R961
R943
R948
R946
R945
R9 06 R 907 R 90 8
R944
R 90 2 R 90 3
R977
R976
R975
R913
R982
R953
R981
R881
R886
R883
R885
R884
IC972
R941
R942
R947
R841
R842
R843
R844
R845
R846
R847
R848
R853
R854
R861
R862
FB905
FB904
C905
FB902
FB901
FB903
S901
S902
S903
S904
LSW901(2/2)
LSW902(2/2)
S907
S908
S909
S910
S911
S912
S913
S914
S915
S906
R 92 2 R 92 1
C974C975
C976
C977
C979
C982
C981
Q991Q992
C992 C991
IC971
R971
FB906
FB907
R905
R882
R887
R888
R889
R994
R993
R995
LSW901(1/2)
LSW902(1/2)
R863
R864
FL901RE901
CN901
CN902
J901
LED941
LED942
L ED9 43 L ED8 43
LED945
LED842
LED841
LED944
LED946
LED844
LED947
LED845
LED847
LED846
LED950
LED951
LED952
LED955
LED852
LED954
LED851
LED953
L ED 85 0 L ED 957
LED853
LED956
LED854
L ED 85 5 L ED 96 3
LED962
LED856
LED857
LED961
LED861
LED863
LED862
LED864
D971
D904
D903
D908
D906
D907
D951 D953
D955
LF901
RB901
D905
(Page 24)
-
7/24/2019 Sony Cdx Gt460us Fm Am
28/46
-
7/24/2019 Sony Cdx Gt460us Fm Am
29/4629
CDX-GT41UW/GT410U/GT460U/GT460US
IC801 NJM2387ADL3 (MAIN Board (3/3))IC802 NJM2387ADL3 (MAIN Board (3/3))
1 2 3 4 5
CURRENT
LIMIT
THERMAL
PROTECTION
OVERVOLTAGE
PROTECTION
BANDGAP
REFERENCE
VIN CONTROL VOUT VADJ GND
IC803 BD9778HFP (MAIN Board (3/3))
1 2 3 4 5
CURRENT
LIMIT
PWM
COMPARATOR
ERROR
AMP
L:OFF
H:ON
VREF
VIN
TSD
OSC
VIN SW PB GND INV
6
RT
7
EN
VREFSOFT
START
ON/OFF
LATCH
DRIVER
RESET
-
7/24/2019 Sony Cdx Gt460us Fm Am
30/4630
CDX-GT41UW/GT410U/GT460U/GT460US
IC PIN DESCRIPTIONIC501 MB90F046PF-G-101E1 (SYSTEM CONTROL) (MAIN BOARD (3/3))
Pin No. Pin Name I/O Pin Description
1 AREASEL0 I Destination setting pin 0
2 AREASEL1 I Destination setting pin 1
3 AREASEL2 I Destination setting pin 24 B-OUTSEL I Black-out with/without discrimination signal input H: Black-out
5 DIAG I Status signal input from power amplifier
6 AAC SEL I AAC play setting signal input
7 BEEP O Beep signal output to power amplifier
8 AMPSTB O Standby signal output to power amplifier
9 VOLATT O Electronic volume attenuate control signal output
10 FSW IN I D/D converter oscillator frequency count signal input
11 VSS Ground pin
12 TUATT O Tuner mute control signal output
13 NSMASK O Noise mask signal output Not used in this set.
14 ILLUMI SEL I Illumination voltage setting signal input
15 COL SEL I Two colors change setting signal input
16, 17 NCO O Not used. (Open)
18 FL CS O Fluorescent indicator tube chip select signal output
19 FL SO O Fluorescent indicator tube serial data signal output
20 FL SCK O Fluorescent indicator tube serial clock signal output
21, 22 NCO O Not used. (Open)
23 VCC5 Power supply pin (+3.3 V)
24 EEP SIO I/O EEPROM bus serial data signal input/output
25 EEP CKO O EEPROM bus serial clock signal output
26 RDS ON O RDS (Radio Data System) on signal output Tuner on: L Not used in this set.27 MC RX I Mechanism microcomputer comunication signal input RX
28 MC TX O Mechanism microcomputer comunication signal output TX
29, 30 NCO O Not used. (Open)
31 RE IN0 I Rotary encoder signal input 0
32 RE IN1 I Rotary encoder signal input 1
33 I2C SCK O I2C bus serial clock signal output
34 I2C SIO I/O I2C bus serial data signal input/output
35 DAVDD A/D converter power supply pin (+3.3 V)
36 AVRH A/D converter external reference power supply pin (+3.3 V)
37 DAVSS Ground pin
38 QUALITY I Noise detect signal input
39 VSM I S-meter voltage detect signal input
40 KEYIN1 I Key signal input 1
41 KEYIN0 I Key signal input 0
42 VSS Ground pin
43 RCIN0 I Rotary commander key signal input Not used in this set.
44 to 47 NCO O Not used. (open)
48 AD ON O A/D converter power supply control signal output
49 MD0 I Operation mode setting pin (Connect to VDD.)
50 MD1 I Operation mode setting pin (Connect to VDD.)
51 MD2 I Operation mode setting pin (Connect to VSS.)
52 KEYACK I Key acknowledgment detect signal input
53 TUATTIN I Tuner mute zero cross detect signal input Not used in this set.
54 BUIN I Back-up power supply detect signal input
-
7/24/2019 Sony Cdx Gt460us Fm Am
31/4631
CDX-GT41UW/GT410U/GT460U/GT460US
55 NCO O Not used. (Open)
56 DAVN IRDS (Radio Data System) data block synchronized detect signal input
Not used in this set.
57 NCO O Not used. (Open)
58 UNISI I SONY bus data signal input59 UNISO O SONY bus data signal output
60 UNISCK O SONY bus clock signal output
61 Z MUTE I Mute signal input
62 NOSE SW I Front panel attachment detect signal input L: With panel, H: Without panel
63 FLASH W IMemory mode change signal input Normally H: Single chip mode, after reset
L: flash write mode
64 SIRCS I Remote control signal input
65 to 70 NCO O Not used. (Open)
71 RC IN1 I Rotary commander shift key signal input Not used in this set.
72 to 74 NCO O Not used. (Open)
75 FSW OUT OD/D converter oscillator frequency shift control signal output
L: 350 kHz, H: 415 kHz
76 NCO O Not used. (Open)
77 RESET I CPU reset signal input
78 NCO (OPEN REQ) O Not used. (Open)
79 XIN I Low speed operation clock signal input (32.768 kHz)
80 XOUT O Low speed operation clock signal output (32.768 kHz)
81 VSS1 Ground pin
82 OSCIN I High speed operation clock signal input (18.432 MHz)
83 OSCOUT O High speed operation clock signal output (18.432 MHz)
84 VCC3 Power supply pin (+3.3 V)
85 CYRIL SEL I Cyril correspondence discrimination signal input L: No correspondence
86 DEMOSEL I DEMO select signal input H: DEMO on, L: DEMO off
87 NCO O Not used. (Open)
88 SYSRST O System reset signal output
89 FL ON O Fluorescent indicator tube power on/off control signal output
90 DD ON O D/D converter power on/off control signal output
91 USB OVER I USB overcurrent detection signal input L: Overcurrent detection
92 USB ON O USB overcurrent detection IC control signal output H: On, L: Off
93 WAKE UP O Mechanism microcomputer wake up signal output H: Wake up, L: Sleep
94 CDON I CD mechanism servo power supply control request signal input95 CDMON I CD mechanism deck power supply control request signal input
96 BUSON O Bus on signal output
97 TESTIN I Test mode detect signal input
98 TELATT I Telephone attenuate detect signal input
99 ACC IN I Accessory power supply detect signal input
100 ATT O Audio mute control signal output
Pin No. Pin Name I/O Pin Description
-
7/24/2019 Sony Cdx Gt460us Fm Am
32/4632
CDX-GT41UW/GT410U/GT460U/GT460US
SECTION 5
EXPLODED VIEWS
1 X-2149-438-1 PANEL (FL-U) ASSY, SUB
2 3-042-244-11 SCREW (T)
3 X-2108-670-1 LOCK ASSY (S)
4 2-050-124-01 SCREW +BTT 2.6X5
5 A-1215-219-A MAIN BOARD, COMPLETE (GT460U/GT460US)
5 A-1215-247-A MAIN BOARD, COMPLETE (GT41UW/GT410U)
6 2-021-848-01 SHEET (TU), GROUND7 1-833-100-11 CORD (WITH CONNECTOR) (POWER)
(EXCEPT GT460US:IND)
7 1-833-762-11 CONNECTION CORD FOR AUTOMOBILE
(POWER) (for Maruti Suzuki) (GT460US:IND)
F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
TU1 A-3220-961-B TUNER UNIT (TUX-032)
#1 7-685-792-09 SCREW +PTT 2.6X6 (S)
#2 7-685-790-01 SCREW +PTT 2.6X4 (S)
#3 7-685-793-09 SCREW +PTT 2.6X8 (S)
#4 7-685-794-09 SCREW +PTT 2.6X10 (S)
#5 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT#6 7-621-284-40 SCREW +P 2.6X10
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
NOTE:
The mechanical parts with no reference
number in the exploded views are not supplied.
Items marked * are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
-XX and -X mean standardized parts, so
they may have some difference from the
original one.
Color Indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ... (RED)
Parts Color Cabinets Color
Accessories are given in the last of this parts list.
Abbreviation
CND : Canadian model
IND : Indian model
5-1. MAIN SECTION
R R
not supplied
not supplied
not supplied
F901
not supplied
TU1
not supplied
not supplied
#1
#1
#1
#3
#4
#4
#5
#6
#3
#4
#2
#1
MG-101U-188//Q
A
A
B
B
1
2
3
4
7
6
A
5
not supplied
The components identified by
mark0or dotted line with mark
0are critical for safety.
Replace only with part number
specified.
Les composants identifis par une
marque0sont critiques pour
la scurit.
Ne les remplacer que par une pice
portant le numro spcifi.
Ver. 1.2
-
7/24/2019 Sony Cdx Gt460us Fm Am
33/4633
CDX-GT41UW/GT410U/GT460U/GT460US
51 A-1215-221-A PANEL COMPLETE ASSY, FRONT (GT460US)
51 A-1215-232-A PANEL COMPLETE ASSY, FRONT (GT460U)
51 A-1215-249-A PANEL COMPLETE ASSY, FRONT (GT41UW:US)
51 A-1215-256-A PANEL COMPLETE ASSY, FRONT (GT410U:US)
51 A-1222-410-A PANEL COMPLETE ASSY, FRONT
(GT41UW:CND)
51 A-1222-411-A PANEL COMPLETE ASSY, FRONT
(GT410U:CND)
52 X-2149-756-1 BUTTON ASSY (S) (GT460US)
52 X-2149-757-1 BUTTON ASSY (S) (GT41UW/GT410U/GT460U)53 X-2149-760-1 PANEL (SV) ASSY, FRONT (GT460US)
53 X-2149-761-1 PANEL (SV) ASSY, FRONT (GT460U)
53 X-2149-762-1 PANEL (SV) ASSY, FRONT (GT41UW)
53 X-2149-763-1 PANEL (SV) ASSY, FRONT (GT410U)
54 X-2149-353-1 KNOB (VOL) (SV) ASSY
55 2-693-599-01 SPRING (RELEASE)
56 2-686-937-02 PANEL (FL-U), BACK
57 3-250-543-21 SCREW (+B P-TITE M2)
58 X-2149-228-2 CASE ASSY (for FRONT PANEL) (EXCEPT US)
59 2-686-941-01 HOLDER (USB)
60 X-2176-322-1 CAP (USB) ASSY
61 3-251-320-01 EMBLEM (NO. 2.5), SONY
CN902 1-820-877-11 CONNECTOR, USB (SOCKET) (USB)
FL901 1-519-909-12 INDICATOR TUBE, FLUORESCENT
RE901 1-479-481-13 ENCODER, ROTARY (PUSH SELECT,VOLUME)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
5-2. FRONT PANEL SECTION
58
59FL901CN902
not supplied(KEY board)
not supplied
not supplied
not supplied
not supplied
not suppliednot supplied(AUX board)
51
52
53
60
54
55
56
57
57
RE901
61
Ver. 1.1
-
7/24/2019 Sony Cdx Gt460us Fm Am
34/4634
CDX-GT41UW/GT410U/GT460U/GT460US
101 A-1177-168-A MECHANICAL BLOCK ASSY
102 A-1177-169-A DAXEV//Q
0103 X-2149-672-1 SERVICE ASSY, OP (DAX-25A)
104 2-626-869-01 SCREW (M2X3), SERRATION
105 3-348-998-31 SCREW (M1.4X2.5), TAPPING, PAN
106 3-352-758-31 SCREW (M1.7X2.5), TOOTHED LOCK
107 A-1206-357-A SERVO BOARD, COMPLETE
#7 7-627-000-08 SCREW, PRECISION +P 1.7X2.2 TYPE3
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
5-3. CD MECHANISM SECTION(MG-101U-188//Q)
NOTE:Refer to SUPPLEMENT-1 for disassembly of OPTICAL PICK-UP.
not supplied
#7#7
not supplied
not supplied
not supplied
not supplied
not supplied
not supplied
not supplied
not supplied
not supplied
not supplied
101
102
103
105
104
107
106not supplied106
Ver. 1.2
-
7/24/2019 Sony Cdx Gt460us Fm Am
35/4635
CDX-GT41UW/GT410U/GT460U/GT460US
SECTION 6
ELECTRICAL PARTS LIST
AUX BOARD
**********
< FERRITE BEAD >
FB901 1-414-595-11 INDUCTOR, FERRITE BEAD
FB902 1-414-595-11 INDUCTOR, FERRITE BEAD
FB903 1-500-245-11 INDUCTOR, FERRITE BEAD
< JACK >
J901 1-819-732-21 JACK (DIA. 3.5) (AUX)
*************************************************************
KEY BOARD
**********
< CAPACITOR >
C905 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC974 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C975 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C976 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C977 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C979 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C981 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C982 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C991 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C992 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
< CONNECTOR >
CN901 1-820-620-11 PLUG, CONNECTOR 24P
< DIODE >
D903 8-719-057-80 DIODE MA8180-M-TX
D904 8-719-057-80 DIODE MA8180-M-TX
D905 8-719-977-12 DIODE DTZ6.8B
D906 8-719-977-12 DIODE DTZ6.8B
D907 8-719-977-12 DIODE DTZ6.8B
D908 8-719-977-12 DIODE DTZ6.8B
D951 1-804-988-21 VARISTOR, CHIP (1608)
D953 1-804-988-21 VARISTOR, CHIP (1608)
D955 1-804-988-21 VARISTOR, CHIP (1608)
D971 8-719-420-90 DIODE MA8051-M
< FERRITE BEAD >
FB904 1-469-876-11 INDUCTOR, FERRITE BEAD
FB905 1-469-876-11 INDUCTOR, FERRITE BEAD
FB906 1-216-295-11 SHORT CHIP 0
FB907 1-216-295-11 SHORT CHIP 0
< FLUORESCENT INDICATOR TUBE >
FL901 1-519-909-12 INDICATOR TUBE, FLUORESCENT
< IC >
IC971 6-600-163-01 IC RS-770 (IR)
IC972 6-706-715-01 IC NJM2867F33(TE2)
< DIODE >
LED841 8-719-078-21 LED SML-310PTT86 (Z)
LED842 8-719-078-21 LED SML-310PTT86 (CD INDICATOR)
LED843 8-719-078-21 LED SML-310PTT86 (OFF)
LED844 8-719-078-21 LED SML-310PTT86 (EQ3)
LED845 8-719-078-21 LED SML-310PTT86 (BTM/CAT)
LED846 8-719-078-21 LED SML-310PTT86 (SOURCE)
LED847 8-719-078-21 LED SML-310PTT86 (MODE)
LED850 8-719-078-21 LED SML-310PTT86 (DSPL/DIM)
LED851 8-719-078-21 LED SML-310PTT86 (1/GP/ALBM )
LED852 8-719-078-21 LED SML-310PTT86 (2/GP/ALBM +)
LED853 8-719-078-21 LED SML-310PTT86 (3/REP)
LED854 8-719-078-21 LED SML-310PTT86 (4/SHUF)
LED855 8-719-078-21 LED SML-310PTT86 (5)
LED856 8-719-078-21 LED SML-310PTT86 (6/PAUSE)
LED857 8-719-078-21 LED SML-310PTT86 (SCRL)
LED861 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION)
LED862 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION)
LED863 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION)LED864 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION)
LED941 8-719-053-09 LED SML-310VTT86 (Z)
LED942 8-719-053-09 LED SML-310VTT86 (CD INDICATOR)
LED943 8-719-053-09 LED SML-310VTT86 (OFF)
LED944 8-719-053-09 LED SML-310VTT86 (EQ3)
LED945 8-719-053-09 LED SML-310VTT86 (BTM/CAT)
LED946 8-719-053-09 LED SML-310VTT86 (SOURCE)
LED947 8-719-053-09 LED SML-310VTT86 (MODE)
LED950 8-719-053-09 LED SML-310VTT86 (DSPL/DIM)
LED951 8-719-053-09 LED SML-310VTT86 (1/GP/ALBM )
LED952 8-719-053-09 LED SML-310VTT86 (2/GP/ALBM +)
LED953 8-719-053-09 LED SML-310VTT86 (3/REP)
LED954 8-719-053-09 LED SML-310VTT86 (4/SHUF)
LED955 8-719-053-09 LED SML-310VTT86 (5)
LED956 8-719-053-09 LED SML-310VTT86 (6/PAUSE)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
NOTE:
Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
-XX and -X mean standardized parts, so
they may have some difference from the
original one.
RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
Items marked * are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
SEMICONDUCTORS
In each case, u : , for example:
uA.. : A.. uPA.. : PA..
uPB.. : PB.. uPC.. : PC.. uPD.. : PD..
CAPACITORS
uF : F
COILS
uH : H
Abbreviation
CND : Canadian model
IND : Indian model
KEYAUX
The components identified by
mark0or dotted line with mark
0are critical for safety.
Replace only with part number
specified.
Les composants identifis par une
marque0sont critiques pour
la scurit.
Ne les remplacer que par une pice
portant le numro spcifi.
When indicating parts by reference
number, please include the board.
Ver. 1.1
-
7/24/2019 Sony Cdx Gt460us Fm Am
36/4636
CDX-GT41UW/GT410U/GT460U/GT460US
LED957 8-719-053-09 LED SML-310VTT86 (SCRL)
LED961 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION)
LED962 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION)
LED963 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION)
< COIL >
LF901 1-457-223-11 COIL, COMMON MODE CHOKE
< SWITCH >
LSW901 1-798-018-11 SWITCH, TACTILE (WITH LED)
(M>SEEK+)
LSW902 1-798-018-11 SWITCH, TACTILE (WITH LED)
(.mSEEK)
< TRANSISTOR >
Q881 8-729-600-22 TRANSISTOR 2SA1235-F
Q882 8-729-600-22 TRANSISTOR 2SA1235-F
Q883 8-729-600-22 TRANSISTOR 2SA1235-F
Q991 6-550-752-01 TRANSISTOR DTC614TKT146Q992 6-550-752-01 TRANSISTOR DTC614TKT146
< RESISTOR >
R841 1-216-810-11 METAL CHIP 120 5% 1/10W
R842 1-216-810-11 METAL CHIP 120 5% 1/10W
R843 1-216-811-11 METAL CHIP 150 5% 1/10W
R844 1-216-810-11 METAL CHIP 120 5% 1/10W
R845 1-216-811-11 METAL CHIP 150 5% 1/10W
R846 1-216-810-11 METAL CHIP 120 5% 1/10W
R847 1-216-811-11 METAL CHIP 150 5% 1/10W
R848 1-216-810-11 METAL CHIP 120 5% 1/10W
R849 1-216-807-11 METAL CHIP 68 5% 1/10W
R850 1-216-807-11 METAL CHIP 68 5% 1/10W
R851 1-216-807-11 METAL CHIP 68 5% 1/10W
R852 1-216-807-11 METAL CHIP 68 5% 1/10W
R853 1-216-811-11 METAL CHIP 150 5% 1/10W
R854 1-216-810-11 METAL CHIP 120 5% 1/10W
R861 1-216-811-11 METAL CHIP 150 5% 1/10W
R862 1-216-810-11 METAL CHIP 120 5% 1/10W
R863 1-216-811-11 METAL CHIP 150 5% 1/10W
R864 1-216-810-11 METAL CHIP 120 5% 1/10W
R881 1-216-821-11 METAL CHIP 1K 5% 1/10W
R882 1-216-821-11 METAL CHIP 1K 5% 1/10W
R883 1-216-821-11 METAL CHIP 1K 5% 1/10W
R884 1-216-833-11 METAL CHIP 10K 5% 1/10W
R885 1-216-833-11 METAL CHIP 10K 5% 1/10W
R886 1-216-833-11 METAL CHIP 10K 5% 1/10W
R887 1-216-845-11 METAL CHIP 100K 5% 1/10W
R888 1-216-845-11 METAL CHIP 100K 5% 1/10W
R889 1-216-845-11 METAL CHIP 100K 5% 1/10W
R901 1-216-820-11 METAL CHIP 820 5% 1/10W
R902 1-216-821-11 METAL CHIP 1K 5% 1/10W
R903 1-216-821-11 METAL CHIP 1K 5% 1/10W
R904 1-216-822-11 METAL CHIP 1.2K 5% 1/10W
R905 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R906 1-216-820-11 METAL CHIP 820 5% 1/10W
R907 1-216-821-11 METAL CHIP 1K 5% 1/10WR908 1-216-821-11 METAL CHIP 1K 5% 1/10W
R909 1-216-822-11 METAL CHIP 1.2K 5% 1/10W
R910 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R911 1-216-824-11 METAL CHIP 1.8K 5% 1/10W
R912 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R913 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R914 1-216-828-11 METAL CHIP 3.9K 5% 1/10W
R915 1-216-830-11 METAL CHIP 5.6K 5% 1/10WR921 1-216-295-11 SHORT CHIP 0
R922 1-216-295-11 SHORT CHIP 0
R941 1-216-813-11 METAL CHIP 220 5% 1/10W
R942 1-216-813-11 METAL CHIP 220 5% 1/10W
R943 1-216-812-11 METAL CHIP 180 5% 1/10W
R944 1-216-811-11 METAL CHIP 150 5% 1/10W
R945 1-216-812-11 METAL CHIP 180 5% 1/10W
R946 1-216-811-11 METAL CHIP 150 5% 1/10W
R947 1-216-812-11 METAL CHIP 180 5% 1/10W
R948 1-216-811-11 METAL CHIP 150 5% 1/10W
R949 1-216-809-11 METAL CHIP 100 5% 1/10W
R950 1-216-809-11 METAL CHIP 100 5% 1/10W
R951 1-216-809-11 METAL CHIP 100 5% 1/10WR952 1-216-809-11 METAL CHIP 100 5% 1/10W
R953 1-216-812-11 METAL CHIP 180 5% 1/10W
R954 1-216-811-11 METAL CHIP 150 5% 1/10W
R961 1-216-809-11 METAL CHIP 100 5% 1/10W
R962 1-216-809-11 METAL CHIP 100 5% 1/10W
R971 1-216-809-11 METAL CHIP 100 5% 1/10W
R975 1-216-811-11 METAL CHIP 150 5% 1/10W
R976 1-216-811-11 METAL CHIP 150 5% 1/10W
R977 1-216-809-11 METAL CHIP 100 5% 1/10W
R978 1-216-864-11 SHORT CHIP 0
R981 1-218-893-11 METAL CHIP 82K 0.5% 1/10W
R982 1-216-841-11 METAL CHIP 47K 5% 1/10W
R983 1-216-801-11 METAL CHIP 22 5% 1/10W
R984 1-216-801-11 METAL CHIP 22 5% 1/10W
R988 1-216-864-11 SHORT CHIP 0
R989 1-216-845-11 METAL CHIP 100K 5% 1/10W
R993 1-216-809-11 METAL CHIP 100 5% 1/10W
R994 1-216-809-11 METAL CHIP 100 5% 1/10W
R995 1-216-809-11 METAL CHIP 100 5% 1/10W
< NETWORK RESISTOR >
RB901 1-239-662-81 RESISTOR, NETWORK 10X2
< ROTARY ENCODER >
RE901 1-479-481-13 ENCODER, ROTARY (PUSH SELECT,VOLUME)
< SWITCH >
S901 1-786-653-21 SWITCH, TACTILE (Z)
S902 1-786-653-21 SWITCH, TACTILE (OFF)
S903 1-786-653-21 SWITCH, TACTILE (SOURCE)
S904 1-786-653-21 SWITCH, TACTILE (EQ3)
S906 1-786-653-21 SWITCH, TACTILE (BTM/CAT)
S907 1-786-653-21 SWITCH, TACTILE (MODE)
S908 1-786-653-21 SWITCH, TACTILE (DSPL/DIM)
S909 1-786-653-21 SWITCH, TACTILE (1/GP/ALBM )
S910 1-786-653-21 SWITCH, TACTILE (2/GP/ALBM +)S911 1-786-653-21 SWITCH, TACTILE (3/REP)
S912 1-786-653-21 SWITCH, TACTILE (4/SHUF)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
KEY
-
7/24/2019 Sony Cdx Gt460us Fm Am
37/4637
CDX-GT41UW/GT410U/GT460U/GT460US
S913 1-786-653-21 SWITCH, TACTILE (5)
S914 1-786-653-21 SWITCH, TACTILE (6/PAUSE)
S915 1-786-653-21 SWITCH, TACTILE (SCRL)
*************************************************************
A-1215-219-A MAIN BOARD, COMPLETE (GT460U/GT460US)
A-1215-247-A MAIN BOARD, COMPLETE (GT41UW/GT410U)*********************
7-621-284-40 SCREW +P 2.6X10
7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT
7-685-794-09 SCREW +PTT 2.6X10 (S)
< CAPACITOR >
C2 1-126-947-11 ELECT 47uF 20% 35V
C3 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C5 1-124-589-11 ELECT 47uF 20% 16V
C6 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C7 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C8 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC15 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C151 1-126-960-11 ELECT 1uF 20% 50V
C152 1-126-960-11 ELECT 1uF 20% 50V
C153 1-126-961-11 ELECT 2.2uF 20% 50V
C157 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C158 1-163-017-00 CERAMIC CHIP 0.0047uF 10% 50V
C159 1-163-017-00 CERAMIC CHIP 0.0047uF 10% 50V
C301 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
C302 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C303 1-128-551-11 ELECT 22uF 20% 63V
C304 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
C305 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C306 1-124-233-11 ELECT 10uF 20% 16V
C307 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C308 1-124-233-11 ELECT 10uF 20% 16V
C309 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
C312 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
C313 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C314 1-124-233-11 ELECT 10uF 20% 16V
C315 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C316 1-124-233-11 ELECT 10uF 20% 16V
C317 1-125-889-11 CERAMIC CHIP 2.2uF 10% 10V
C318 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C319 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C320 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C325 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
C329 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C330 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
C361 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C362 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C363 1-126-160-11 ELECT 1uF 20% 50V
C364 1-126-160-11 ELECT 1uF 20% 50V
C365 1-126-960-11 ELECT 1uF 20% 50V
C366 1-126-960-11 ELECT 1uF 20% 50V
C401 1-124-234-00 ELECT 22uF 20% 16V
C402 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C403 1-124-584-00 ELECT 100uF 20% 10VC405 1-124-234-00 ELECT 22uF 20% 16V
C406 1-124-257-00 ELECT 2.2uF 20% 50V
C407 1-124-257-00 ELECT 2.2uF 20% 50V
C409 1-124-233-11 ELECT 10uF 20% 16V
C412 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C413 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C414 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C415 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC417 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C418 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C419 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C421 1-126-964-11 ELECT 10uF 20% 50V
C423 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C424 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C426 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C431 1-126-964-11 ELECT 10uF 20% 50V
C432 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C434 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C441 1-126-964-11 ELECT 10uF 20% 50V
C443 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C444 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC445 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C451 1-126-964-11 ELECT 10uF 20% 50V
C452 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C454 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C461 1-126-964-11 ELECT 10uF 20% 50V
C462 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C463 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C471 1-126-964-11 ELECT 10uF 20% 50V
C472 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C473 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C484 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C485 1-126-933-11 ELECT 100uF 20% 16V
C486 1-126-964-11 ELECT 10uF 20% 50V
C491 1-124-589-11 ELECT 47uF 20% 16V
C493 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V
C494 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V
C501 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C502 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C504 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C507 1-162-917-11 CERAMIC CHIP 15PF 5% 50V
C508 1-162-917-11 CERAMIC CHIP 15PF 5% 50V
C509 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C510 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C512 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C513 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C514 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C515 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C516 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C519 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C600 1-126-935-11 ELECT 470uF 20% 16V
C601 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C622 1-126-924-11 ELECT 330uF 20% 10V
C623 1-126-916-11 ELECT 1000uF 20% 6.3V
C624 1-124-584-00 ELECT 100uF 20% 10V
C625 1-124-584-00 ELECT 100uF 20% 10V
C626 1-124-584-00 ELECT 100uF 20% 10V
C681 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C682 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C683 1-124-584-00 ELECT 100uF 20% 10V
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
MAINKEY
-
7/24/2019 Sony Cdx Gt460us Fm Am
38/4638
CDX-GT41UW/GT410U/GT460U/GT460US
C701 1-131-868-81 ELECT 3300uF 20% 16V
C702 1-164-005-11 CERAMIC CHIP 0.47uF 25V
C703 1-164-005-11 CERAMIC CHIP 0.47uF 25V
C704 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
C705 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
C706 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50VC707 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C801 1-126-933-11 ELECT 100uF 20% 16V
C802 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C803 1-124-589-11 ELECT 47uF 20% 16V
C804 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C805 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C806 1-124-589-11 ELECT 47uF 20% 16V
C807 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C808 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C809 1-126-933-11 ELECT 100uF 20% 16V
C810 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C811 1-124-584-00 ELECT 100uF 20% 10V
C812 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25VC814 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C815 1-126-933-11 ELECT 100uF 20% 16V