sony gps navigation nv-u83t
TRANSCRIPT
-
SERVICE MANUAL
Published by Sony Techno Create Corporation
Sony CorporationAudio&Video Business Group
SPECIFICATIONS
PERSONAL NAVIGATION SYSTEM9-887-837-042008G05-1 2008.07
US ModelCanadian Model
NV-U83T
AEP ModelNV-U83F/U83N/U83S/
U93TC/U93TW
UK ModelNV-U83G/U93TW
Ver. 1.3 2008.07
NV-U83/U83T/U93TNV-U83F/U83G/U83N/U83S/U83T/U93TC/U93TW
Photo: NV-U93TW
Model Name Product Name(Printed on Model Number Label) Destination
NV-U83
NV-U83F FrenchNV-U83G UKNV-U83N NordicNV-U83S Iberia
NV-U83T NV-U83T US, Canadian
NV-U93TNV-U93TC East EuropeanNV-U93TW West European
DESTINATION TABLENV-U83 NV-U83T/U93T
Main Unit * *
Cradle NVA-CU5 NVA-CU5TCar battery adapter XA-DC3
COMPONENT MODEL NAME
*Note: Refer to the above table for the model name being written in MODEL NUMBER LABEL of the main unit.
Main unitOperating temperature: 5 45 C (41 113 F)Power requirements: DC 5 V from supplied USB cable or optional AC
adapterConnection terminals: Cradle connector DC IN 5V jack USB jack Headphone jackMemory card slot: Memory Stick Duo slotSpeaker: 20 40 mm (0.8 1.6 in) oval speakerConsumption current: Max. 1.5 ADimensions: Approx. 145 87 20 mm (5.7 3.4 0.8 in) (w h d, protruding parts excluded)Mass: Approx. 250 g (8.8 oz)MonitorSystem: Transmissive liquid crystal displayDrive system: a-Si TFT active matrix systemDimensions: 4.8 in (16:9) Approx. 106 60, 122 mm (4.2 2.4, 4.8 in) (h v, d)Segment: 391,680 (816 480) dots
Wireless CommunicationCommunication System: Bluetooth Standard version 2.0Output: Bluetooth Standard Power Class 2 (Max. +4 dBm)Maximum communication range: Line of sight approx. 10 m (32.8 ft)*1Frequency band: 2.4 GHz band (2.4000 2.4835 GHz)
Modulation method: FHSSCompatible Bluetooth Profi les*2: HFP (Hands-free Profi le) OPP (Object Push Profi le)
*1 The actual range will vary depending on fac-tors
such as obstacles between devices, magnetic fi elds around a microwave oven, static elec-
tricity, reception sensitivity, aerials performance, operating system, software application, etc.*2 Bluetooth standard profi les indicate the pur-
pose of Bluetooth communication between devices.
CradleOperating temperature: 5 45 C (41 113 F)Power requirements: DC 5.2 V from supplied 12 V/24 V car battery adapter (negative earth)Connection terminals: Unit connector DC IN 5.2V jack TMC aerial jack (NV-U83T/U93T)Reception frequency: 87.5 108.0 MHz (NV-U83T/U93T)
Built-in battery charging time/usage timeCharging timeWith the supplied car battery adapter/optional
ACadapter: Approx. 3 hours (with unit turned on), or 1.5 hours (in standby mode)With the supplied USB cable: Approx. 3 hours (in standby mode)Usage time Up to 2 hours (depending on usage)
Supplied accessories Cord (with Cigar Lighter Plug) Connection Cord (USB5P) Connection Cord (Antenna) (NV-U83T/U93T) Application Disc Quick Start Guide (Except NV-U83T) Read This First Before you use (NV-U83T) Warranty Card (Except NV-U83T) END-USER LICENSE AGREEMENT Design and specifi cations are subject to changewithout notice.
-
NV-U83/U83T/U93T
2
Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Flexible Circuit Board Repairing Keep the temperature of soldering iron around 270 C during
repairing. Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times). Be careful not to apply force on the conductor when soldering
or unsoldering.
1. SERVICING NOTES ............................................. 3
2. GENERAL .................................................................. 4
3. DISASSEMBLY3-1. Disassembly Flow .......................................................... 73-2. Front Block Assy ............................................................ 83-3. SENSOR Board, Lithium Ion Battery (BAT3001) ......... 93-4. MAIN Board .................................................................. 93-5. Liquid Crystal Display Panel (LCD5001) ...................... 103-6. Microphone (MIC3501), Touch Panel Switch (TPS5001) ...................................... 103-7. GPS Antenna Block Assy (ANT4001) ............................ 113-8. CRADLE (MID) Board ................................................. 11
4. TEST MODE ............................................................ 12
5. DIAGRAMS5-1. Block Diagram - MEMORY/LCD/SENSOR Section - ........................... 185-2. Block Diagram - MAIN Section - ................................... 195-3. Block Diagram - POWER SUPPLY Section - ................ 205-4. Printed Wiring Boards - MAIN Section (1/2) - .............. 225-5. Printed Wiring Board - MAIN Section (2/2) - ................ 235-6. Schematic Diagram - MAIN Section (1/10) - ................. 245-7. Schematic Diagram - MAIN Section (2/10) - ................. 255-8. Schematic Diagram - MAIN Section (3/10) - ................. 265-9. Schematic Diagram - MAIN Section (4/10) - ................. 275-10. Printed Wiring Boards - ANT/MS DUO Boards - .......... 275-11. Schematic Diagram - MAIN Section (5/10) - ................. 285-12. Schematic Diagram - MAIN Section (6/10) - ................. 295-13. Schematic Diagram - MAIN Section (7/10) - ................. 305-14. Schematic Diagram - MAIN Section (8/10) - ................. 315-15. Schematic Diagram - MAIN Section (9/10) - ................. 325-16. Schematic Diagram - MAIN Section (10/10) - ............... 335-17. Schematic Diagram - SENSOR Board - ......................... 34
6. EXPLODED VIEWS6-1. Rear Panel Section ......................................................... 496-2. Front Block Assy Section ............................................... 506-3. Cradle Section (NVA-CU5: for NV-U83) (NVA-CU5T: for NV-U83T/U93T) ................................ 51
7. ELECTRICAL PARTS LIST .............................. 52
TABLE OF CONTENTS
Note 1: Refer to SUPPLEMENT-1 for the TEST MODE of NV-U83T. When repairing the set of NV-U83/U93T, refer to either of original service manual according to the set.
Note 2: Refer to SUPPLEMENT-1 for the ANT, MAIN and SENSOR boards of printed wiring boards, schematic diagrams and electrical parts list of NV-U83T. When repairing the set of NV-U83/U93T, refer to either of original service manual/SUPPLEMENT-1 according to the set.
Note 3: Refer to SUPPLEMENT-1 for the CRADLE (MID) board of electrical parts list of NV-U83T. When repairing the set of NV-U83/U93T, refer to either of original service manual/SUPPLEMENT-1.
Microsoft and Windows are registered trademarks of Microsoft Corporation. Memory Stick, , Memory Stick Duo, , Memory Stick
, Memory Stick Micro (M2), MagicGate,, nav-u and are trademarks of Sony Corporation.
MagicGate is a generic name of a copyright protection technology, developed by SonyCorporation.
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use ofsuch marks by Sony Corporation is under license.
All other trademarks are trademarks of their respective owners.
1993 2007 NAVTEQ. All Rights Reserved.
Austria Bundesamt fr Eich- und VermessungswesenBelgiumTraffic Information is provided by the Ministerie van de Vlaamse Gemeenschap and theMinistrie de lEquipement et des Transports.Croatia, Estonia, Latvia, Lithuania, Poland, Slovenia
EuroGeographicsFrancesource: Goroute IGN France & BD Carto IGN FranceGermanyDie Grundlagendaten wurden mit Genehmigung der zustndigen Behrden entnommenGreat BritainBased upon Crown Copyright material.GreeceCopyright Geomatics Ltd.HungaryCopyright 2003; Top-Map Ltd.ItalyLa Banca Dati Italiana stata prodotta usando quale riferimento anche cartografianumerica ed al tratto prodotta e fornita dalla Regione Toscana.NorwayCopyright 2000; Norwegian Mapping AuthorityPortugalSource: IgeoE PortugalSpainInformacin geogrfica propiedad del CNIGSwedenBased upon electronic data National Land Survey Sweden.SwitzerlandTopografische Grundlage: Bundesamt fr Landestopographie.
V-Trafic Information in France is provided by Mediamobile company.
Traffic Information in the UK is provided by ITIS Holdings Plc.
NV-U83/U93T
NV-U83T Microsoft, Windows and Windows Vista are registered trademarks of
Microsoft Corporation in the United States and other countries. Memory Stick, , Memory Stick Duo, ,
, Memory Stick Micro (M2), MagicGate, , nav-u and are
MagicGate is a generic name of a copyright protection technology, developed by Sony Corporation.
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc.and any use of such marks by Sony Corporation is under license.
All other trademarks are trademarks of their respective owners.
2007 NAVTEQ. All Rights Reserved.The data for areas of Canada includes information taken with permissionfrom Canadian authorities, including: Her Majesty the Queen in Right ofCanada, Queens Printer for Ontario, Canada Post Corporation, GeoBase.Copyright 2007 ZENRIN CO., LTD. All Rights Reserved.
Portions of this software are copyright 2007 The FreeType Project(www.freetype.org). All rights reserved.
Memory Stick PRO Duo,
trademarks of Sony Corporation.
PRO Duo,
-
NV-U83/U83T/U93T
3
SECTION 1SERVICING NOTES
UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARKUnleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higher
than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to
about 350 C.Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscou-s (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.
Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
NOTE OF CHECKING THE TEST MODEProgram data for test mode and special USB cable for test mode is necessary to confi rm the test mode.Confi rm the method of obtaining the program data for test mode to each service headquarters.Use the Part No. J-2502-111-1 for special USB cable for test mode.
NOTE OF REPLACING THE MAIN BOARDWhen the MAIN board is exchanged, the writing work of data is necessary. Confi rm details to each service headquarters.
NOTE OF REPLACING THE SENSOR BOARDWhen the SENSOR board is exchanged, the G sensor caribration is necessary. Confi rm details to each service headquarters.
NOTE OF REPLACING THE PARTSIC1001, IC1502, IC1503, IC1505, IC2001, IC3002, IC3003, IC3501, IC4502, IC4503, IC4505 on the MAIN board and IC9511 on the SENSOR board cannot exchange with single. When IC1001, IC1502, IC1503, IC1505, IC2001, IC3002, IC3003, IC3501, IC4502, IC4503, IC4505 on the MAIN board and IC9511 on the SENSOR board are damaged, exchange the entire mounted board.
US, Canadian models
Using the Supplied SoftwareYou can install the software to your computer from the supplied disc.Using the software, you can manage various data to use on the unit.
System requirementsComputer IBM PC/AT compatible machines CPU: Pentium III Processor 800 MHz or faster Hard Disc space: 300 MB or more (500 MB or more recommended) RAM: 128 MB or more (256 MB or more recommended) USB port
OS Microsoft Windows 2000 Professional with Service Pack 4 (or later) Microsoft Windows XP Home Edition/Professional with Service
Microsoft Windows XP Media Center Edition/Media Center Edition
Microsoft Windows Vista Home Basic/Home Premium/Business/
MonitorHigh color (16-bit color) or more, 1024 768 dots or more
OtherInternet connection for data download and supportNotes The following system environments are not supported.
Non IBM PC type computers, such as NEC PC 98 series, Macintosh, etc. Homemade computers OS upgraded computers Multi-monitor environment Multi-boot environment
Depending on the computer condition, operation may not be possible even
Pack 2 (or later)
2004/Media Center Edition 2005
Ultimate
with the recommended environment.
Starting the software1 Start the software.
Click start, then select (All) Programs D nav-u tool Dnav-u tool.The main menu appears.
To manage the map data. To manage the address book data. To select the language for software on-screen displays. To upgrade the firmware. To manage guidance voice data. To access to the Sony navigation support site. To exit the software.
-
NV-U83/U83T/U93T
4
PRECAUTION WHEN HANDING THE FLEXIBLE FLAT CABLE (10 CORE)Repeated connection and disconnection of the fl exible fl at cable (10 core), which connects the MS DUO board and the MAIN board, from the connector could the bended portion to be broken. Handle the fl exible fl at cable (10 core) with extreme care when connecting it to or disconnecting it from the connector.
PRECAUTION WHEN DISASSEMBLING THE MAIN UNITThe jig is required to remove the front block assy of the main unit.Please prepare the following jig: 3-216-496-01 SPACER (RE-WORK)
Note: Follow the disassembly procedure in the numerical order given.
screwdriver
screw hole
six claws Push this part with a screwdriver inserted in a screw hole to detach the front block assy.
Insert the jig (3-216-496-01) into a clearance made by detaching the front block assy.
Make the jig (3-216-496-01) go round along the clearance in the front block assy to release the six claws.
AEP, UK models
Using the Supplied Software
The major functions of the software on the supplied disc areintroduced below.If you insert the disc into your computer, the screen appearsautomatically. Follow the on-screen instructions.
Contents
*1 Installation is required only for Windows 2000/Windows XP users.*2 The Map Manager function can be used only for the model with the disc
containing map data.
Install PC Connection Software*1PC connection software (ActiveSync) can be installed. Be sure to logon as administrator when installing this software.Language ManagerLanguage data for on-screen display and voice guidance can be added to the unit, and unnecessary language data can be deleted from the unit.Read the ManualYou can read the PDF manual which contains further information onoperations available.Support LinkEasy access to the Sony navigation support site is available.Visit this site for technical support, such as software updates, FAQs, etc.Map Manager*2Map data can be copied to the unit or Memory Stick (not supplied)from the supplied disc.When copying, you may need to delete unnecessary map data to freeup memory space.
This section is extracted from instruction manual.
B / (on/standby) buttonTo turn the unit on/off.
C Built-in microphoneTo talk on the telephone using the Bluetoothfunction.
D Screen buttonsE Display window/touch screenF Auto dimmer sensor
Detects ambient light and automaticallyadjusts the display brightness.
G (Bluetooth) indicatorLights up in blue while outputting theBluetooth signal.
H CHG (battery charge) indicatorLights up in red while charging, and changesto green when fully charged.When the adapter is disconnected, theindicator goes off.
I Cradle connectorJ RESET buttonK DC IN 5V jack
To connect to the car battery adapter or ACadapter*.
L (USB) jackTo connect to a computer with the USBcable.
M OPEN/RELEASE buttonTo open the built-in GPS aerial or remove theunit from the cradle.For details, see the supplied Read ThisFirst (Installation Manual).
N NameplateO Built-in GPS aerialP Speaker
Outputs guidance and warnings.Q Memory Stick access indicatorR (Memory Stick Duo) slot
For Memory Stick Duo insertion forfunctional expansion.
S J (headphones) jack
SECTION 2GENERAL
NV-U83/U93T
NV-U83T
/ (on/standby) button Built-in microphone for hands-free MENU button VOICE/POS. button
To show the current position and hear the next voice guidance.
Display window/touch screen (Bluetooth) indicator
Blue: Bluetooth signal on.
CHG (battery charge) indicatorRed: charging. Green: fully charged. O: adapter disconnected.
Cradle connector
RESET button DC IN 5V jack
To connect to the optional AC adapter.
(USB) jack OPEN/RELEASE button
To open the built-in GPS antenna or remove the unit from the cradle.
Nameplate Built-in GPS antenna Speaker Memory Stick access indicator (Memory Stick Duo) slot (headphones) jack
-
55NV-U83/U83T/U93T
NV-U83/U83T/U93T
Dashboard installationNotes Choose a surface that is as smooth and horizontal as possible for attachment. The cradle may not
attach properly on a curved surface. Clean the surface of the dashboard with a soft, dry cloth. After each use, please detach the cradle from the dashboard or windscreen.
Installation am ArmaturenbrettHinweise Whlen Sie fr die Montage eine mglichst glatte und horizontale Flche. Auf einer gebogenen
Flche lsst sich die Anschlussstation mglicherweise nicht richtig anbringen. Reinigen Sie die Oberfl che des Armaturenbretts mit einem weichen, trockenen Tuch. Nehmen Sie die Anschlussstation nach Gebrauch immer vom Armaturenbrett oder der
Windschutzscheibe ab.
Installation sur le tableau de bordRemarques Choisissez une surface de fi xation la plus lisse et la plus horizontale possible. Le support risque
de ne pas rester fi x correctement sur une surface incurve. Nettoyez la surface du tableau de bord avec un chiff on doux et sec. Aprs chaque utilisation, dtachez le support du tableau de bord ou du pare-brise.
Installatie op het dashboardOpmerkingen Kies een zo glad en horizontaal mogelijk oppervlak om de houder te bevestigen. De houder kan
mogelijk niet goed worden bevestigd op een gebogen oppervlak. Reinig het oppervlak van het dashboard met een zachte, droge doek. Verwijder de houder na elk gebruik van het dashboard of de voorruit.
1
TipRetain the removed protection sheet and attach it to the suction cup when you detach the cradle from the dashboard to keep the suction cup clean.
TippNehmen Sie die Schutzfolie ab und heben Sie sie auf. Bringen Sie die Schutzfolie wieder am Saugnapf an, wenn Sie die Anschlussstation vom Armaturenbrett abnehmen, um den Saugnapf vor Verunreinigungen zu schtzen.
ConseilConservez la feuille de protection que vous avez enleve et fi xez-la la ventouse lorsque vous dtachez le support du tableau de bord, afi n de garder la ventouse propre.
TipBewaar het verwijderde bevestigingsvel en bevestig dit op de zuignap wanneer u de houder van het dashboard verwijdert zodat de zuignap schoon blijft.
2
3NoteBe sure to use the supplied or optional car battery adapter, which is compatible with the cradle. Otherwise, excessive voltage may be applied to the unit/cradle and may cause smoke, fi re or accident.For details on optional accessories, refer to Optional accessories in the Specifi cations section of the supplied Quick Start Guide.
HinweisVerwenden Sie unbedingt den mitgelieferten oder einen gesondert erhltlichen Autobatterieadapter, der mit der Anschlussstation kompatibel ist. Andernfalls wird das Gert/die Anschlussstation bermiger Spannung ausgesetzt und es kann zu Rauchentwicklung kommen bzw. es besteht Feuer- und Unfallgefahr.Weitere Informationen zum Sonderzubehr fi nden Sie unter Sonderzubehr im Abschnitt Technische Daten in der mitgelieferten Anleitung zur schnellen Inbetriebnahme.
RemarqueVeillez utiliser ladaptateur pour batterie de voiture fourni ou en option, compatible avec le support. Sinon, une tension excessive risque dtre applique lappareil/au support et de provoquer lmission de fume, un incendie ou un accident.Pour plus dinformations sur les accessoires en option, reportez-vous la partie Accessoires en option de la section Spcifi cations du Guide de dmarrage rapide fourni.
OpmerkingGebruik de bijgeleverde of optionele accuadapter, die compatibel is met de houder. Als u dit niet doet, kan het apparaat/de houder te veel spanning ontvangen. Dit kan rook, brand of een ongeluk tot gevolg hebben.Raadpleeg "Optionele accessoires" in het gedeelte "Technische gegevens" van de bijgeleverde "Beknopte handleiding" voor meer informatie over optionele accessoires.
4
Click
5 6
Detaching the unitWhile pressing the OPEN/RELEASE button on the bottom of the unit, detach the unit from the cradle.
Abnehmen des GertsHalten Sie die Taste OPEN/RELEASE an der Unterseite des Gerts gedrckt und nehmen Sie das Gert von der Anschlussstation ab.
Retrait de lappareilTout en appuyant sur la touche OPEN/RELEASE situe sous lappareil, dtachez lappareil de son support.
Het apparaat verwijderenHoud de toets OPEN/RELEASE ingedrukt op de onderkant van het apparaat terwijl u het apparaat uit de houder verwijdert.
1
2
3
Detaching the cradle After each use, please detach the cradle from the dashboard or windscreen. Do not detach the cradle by forcing your fi nger under the suction cup. This may damage the
suction cup. It may be diffi cult to detach the cradle at low temperatures.
Abnehmen der Anschlussstation Nehmen Sie die Anschlussstation nach Gebrauch immer vom Armaturenbrett oder der
Windschutzscheibe ab. Lsen Sie die Anschlussstation nicht, indem Sie den Finger mit Gewalt unter den Saugnapf
schieben. Andernfalls knnte der Saugnapf beschdigt werden. Bei niedrigen Temperaturen lsst sich die Anschlussstation mglicherweise nur schwer abnehmen.
Retrait du support Aprs chaque utilisation, dtachez le support du tableau de bord ou du pare-brise. Ne dtachez pas le support en forant pour passer le doigt sous la ventouse. Cela pourrait
endommager la ventouse. Le support risque dtre diffi cile dtacher basse temprature.
De houder verwijderen Verwijder de houder na elk gebruik van het dashboard of de voorruit. Verwijder de houder niet door uw vinger onder de zuignap te duwen. Als u dit wel doet, kan de
zuignap worden beschadigd. Bij lage temperaturen kan het moeilijk zijn de houder te verwijderen.
1 2
Turning the unit on/off
Ein-/Ausschalten des Gerts
Mise sous/hors tension de lappareil
Het apparaat in-/uitschakelen
TMC aerial installation (NV-U93T only)Install the supplied TMC aerial to receive traffic information over the RDS-TMC (Traffic Message Channel).Installation der TMC-Antenne (nur NV-U93T)Installieren Sie die mitgelieferte TMC-Antenne . So knnen Sie Verkehrsinformationen ber RDS-TMC (Traffic Message Channel) empfangen.Installation de lantenne TMC (modle NV-U93T uniquement)Installez lantenne TMC fournie afin de recevoir des informations de radioguidage via RDS-TMC (Traffic Message Channel, canal des messages de radioguidage).Installatie van de TMC-antenne (alleen NV-U93T)Installeer de bijgeleverde TMC-antenne om verkeersinformatie via RDS-TMC (Traffic Message Channel) te ontvangen.
Windscreen installationBefore attaching the cradle, rotate the suction cup section.
Installation an der WindschutzscheibeDrehen Sie den Saugnapf, bevor Sie die Anschlussstation anbringen.
Installation sur le pare-briseAvant de fi xer le support, faites tourner la ventouse.
Installatie op de voorruitVoordat u de houder bevestigt, moet u de zuignap draaien.
NV-U83/U93T
-
66NV-U83/U83T/U93T
NV-U83/U83T/U93T
NV-U83T
B Dashboard installation / Installation sur le tableau de bord / Instalacin en el tablero
1 Attaching the cradle to the dashboard / Fixation du support sur le tableau de bord / Instalacin de la base en el tablero
Choose a surface that is as smooth and horizontally at as possible for attachment. The cradle may not attach properly on a curved surface. Clean the surface of the dashboard with a soft,
dry cloth.
Choisissez une surface de xation la plus lisse et la plus horizontale possible. Le support risque de ne pas tre x correctement sur une surface incurve. Nettoyez la surface du tableau de bord avec un
chion doux et sec.
Elija una supercie lo ms uniforme, horizontal y plana posible para realizar la instalacin. Es posible que la base no se adhiera correctamente en una supercie curva. Limpie la supercie del tablero con un pao
suave y seco.
Retain the removed protection cover and attach it to the suction cup when you detach the cradle from the dashboard to keep the suction cup clean.
Conservez le capuchon de protection que vous avez enlev et xez-le la ventouse lorsque vous dtachez le support du tableau de bord, an de garder la ventouse propre.
Conserve la lmina de proteccin que ha retirado y adhirala a la ventosa cuando retire la base del tablero para mantener limpia la ventosa.
C Windshield installation / Installation sur le pare-brise / Instalacin en el parabrisas
ROTATE
2 Connecting to the car cigarette lighter socket / Raccordement la prise de lallume-cigare du vhicule / Conexin a la toma del encendedor del automvil
3 Opening the built-in GPS antenna / Ouverture de lantenne GPS intgre / Apertura de la antena GPS integrada
CLICK
4 Attaching the unit to the cradle / Fixation de lappareil sur le support / Instalacin de la unidad a la base
5 Adjusting the monitor angle / Rglage de langle du moniteur / Ajuste del ngulo del monitor
D TMC antenna installation / Installation de lantenne TMC / Instalacin de la antena TMC
E Detaching the unit / Retrait de lappareil / Extraccin de la unidad
While pressing OPEN/RELEASE on the bottom of the unit, detach the unit from the cradle. Tout en appuyant sur la touche OPEN/RELEASE situe sous lappareil, dtachez lappareil de son support. Con el botn OPEN/RELEASE de la parte inferior de la unidad presionado, desconecte la unidad de la base.
F Detaching the cradle / Retrait du support / Extraccin de la base
TabOngletLengeta
Notes After each use, detach the cradle from the dashboard
or windshield. Be sure to use the suction cup tab when detaching
the cradle to avoid damage to the suction cup. Do not detach the cradle by forcing your nger under
the suction cup. This may damage the suction cup. It may be dicult to detach the cradle at low
temperatures.
Remarques Aprs chaque utilisation, dtachez le support du
tableau de bord ou du pare-brise. Pour dtacher le support, veillez utiliser longlet de
la ventouse an dviter de lendommager. Ne dtachez pas le support en forant pour passer le
doigt sous la ventouse. Cela pourrait endommager la ventouse. Le support risque dtre dicile dtacher basse
temprature.
Notas Despus de cada uso, extraiga la base del tablero o
del parabrisas. Para no daar la ventosa, asegrese de utilizar la
lengeta de la ventosa cuando extraiga la base. No introduzca el dedo a la fuerza en la parte
inferior de la ventosa para extraer la base. Este procedimiento podra daarla. Puede resultar difcil extraer la base cuando la
temperatura es baja.
-
NV-U83/U83T/U93T
7
SECTION 3DISASSEMBLY
This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
3-2. FRONT BLOCK ASSY (Page 8)
3-3. SENSOR BOARD, LITHIUM ION BATTERY (BAT3001) (Page 9)
3-7. GPS ANTENNA BLOCK ASSY (ANT4001) (Page 11)
3-4. MAIN BOARD (Page 9)
3-5. LIQUID CRYSTAL DISPLAY PANEL (LCD5001) (Page 10)
3-6. MICROPHONE (MIC3501), TOUCH PANEL SWITCH (TPS5001) (Page 10)
3-8. CRADLE (MID) BOARD (Page 11)
SET (CRADLE)SET (MAIN UNIT)
-
NV-U83/U83T/U93T
8
Note: Follow the disassembly procedure in the numerical order given.
3-2. FRONT BLOCK ASSY
two foots (MID)
two foot sheets
screw (M2.6) (3.5 mm)
screw (M2.6) (10 mm)
Push the button (GPS open).
Open the GPS antenna block assy.
two screws (M2.6) (5 mm)
screwdriver
screw hole
six claws Push this part with a screwdriver inserted in a screw hole to detach the front block assy.
Insert the jig (3-216-496-01) into a clearance made by detaching the front block assy.
R Make the jig (3-216-496-01) go round along the clearance in the front block assy to release the six claws.
RT While pusing the button (GPS open), open the front block assy.
RB Open the front block assy upper side.
RE connector (CN3502)RG connector (CN4007)
RH flexible flat cable (10 core) (CN2501)
RI front block assy
Note: Foot sheet cannot re-used. Please replace to brand-new part ones foot sheet is removed.
rear view
rear view
Note: The jig is required to remove the front block assy of the main unit. Please prepare the following jig: 3-216-496-01 SPACER (REWORK)
PRECAUTION WHEN HANDING THE FLEXIBLEFLAT CABLE (10 CORE)Repeated connection and disconnection of the flexibleflat cable (10 core), which connects the MS DUO boardand the MAIN board, from the connector could thebended portion to be broken. Handle the flexible flatcable (10 core) with extreme care when connecting itto or disconnecting it from the connector.
-
NV-U83/U83T/U93T
9
3-3. SENSOR BOARD, LITHIUM ION BATTERY (BAT3001)
3-4. MAIN BOARD
screw
sheet (GPS wire)RB flexible flat cable (8 core) (MAIN board: CN6001, SENSOR board: CN9503)
claw
RE SENSOR board
RT sensor protection sheet
connector (CN3001)
cushion (BATT)
cover (battery)
Lift up the lithium ion battery (BAT3001) section.
R lithium ion battery (BAT3001)
adhesive sheet (BAT)
Note 1: Adhesive sheet (BAT) cannot re-used. Please replace to brand-new part ones adhesive sheet (BAT) is removed.
Remove the SENSOR board in the direction of the arrow.
front block rear view
Note 2: When the SENSOR board is exchanged, the G sensor caribration is necessary. Confirm details to each service headquarters.
two screws
screw (M2)
two connectors (CN3501, CN5003)
two claws
touch panel switch flexible board (CN5001)
sheet (GPS wire)
lead wire (with connector) (CN5501)
liquid crystal flexible board (CN5002)
R MAIN board
front block rear view
-
NV-U83/U83T/U93T
10
3-5. LIQUID CRYSTAL DISPLAY PANEL (LCD5001)
3-6. MICROPHONE (MIC3501), TOUCH PANEL SWITCH (TPS5001)
screw
two screws spring (GPS open)
button (GPS open)
claw
liquid crystal display panel (LCD5001)
front panel block
chassis block
front block rear view
two screws
microphone case
microphone (MIC3501)
mic case sheet touch panel switch (TPS5001)
front panel block
two adhesive sheets (TP)
Note: Adhesive sheet (TP) cannot re-used. Please replace to brand-new part ones adhesive sheet (TP) is removed.
front block rear view
-
NV-U83/U83T/U93T
11
3-7. GPS ANTENNA BLOCK ASSY (ANT4001)
3-8. CRADLE (MID) BOARD
connector
Push the GPS antenna hinges.
GPS antenna block assy (ANT4001)
two screws
two screws
cradle (front) block
two screws
CRADLE (MID) board
-
NV-U83/U83T/U93T
12
SECTION 4TEST MODE
1. PREPARATIONPrepare the following before confi rming the test mode. Memory Stick Duo (128 MB or more) Special USB cable (Part No. J-2502-111-1)
2. NOTE OF CHECKING THE TEST MODEProgram data for test mode and special USB cable for test mode is necessary to confi rm the test mode.Confi rm the method of obtaining the program data for test mode to each service headquarters.Use the Part No. J-2502-111-1 for special USB cable for test mode.Test mode software will be updated according factory request.
3. OUTLINENecessary following function can be used by service by executing the test mode.1. Version display (Ver.)2. Shipment setting (Ship)3. Diagnosis function (Diag)4. LCD/touch panel test (LCD)5. Audio test (Audio)6. GPS test (GPS)7. Cradle test (Cradle)8. Bluetooth test (BT)9. Firmware update (FWUpdate)10. RDS test (RDS)11. Movi data copy (Disk)12. Log display (Log)
4. SETTING THE TEST MODEProcedure:1. Insert the Memory Stick Duo in which program fi le for test
mode is written in the main unit and connect the special USB cable to the main unit
2. Press the [RESET] button, then while touching the upper right corner of the main unit screen and press the [?/1] button.
3. After starting the test mode, Memory Stick Duo can be taken out and special USB cable can be disconnected.
When test mode is set fi rst, 6-4-4. Touch panel (2. Start Calibra-tion) is performed.Refer to 6-4-4. Touch panel (2. Start Calibration) for details.
5. RELEASING THE TEST MODEPress the [RESET] button and turn off the power.
6. OPERATION OF THE TEST MODETest mode is operated by touching the screen.
6-1. Version Display (Ver.)
6-1-1. S/NSerial number of the main unit is displayed usually. It is displayed at the error as No Bin File Existed.
6-1-2. FWBootStrap version, Boot Loader version and Recovery version are displayed usually. It is displayed at the error as ---.When File compare Result: NG is displayed in the last line, there is not the abnormality.
6-1-3. Map verMap data version and movi-NAND size are displayed usually. It is displayed at the error as Fail to mount MapData, Fail to fi nd *.map or movi-NAND size: not found.When File compare Result: NG is displayed in the last line, there is not the abnormality.
6-2. Shipment Setting (Ship)This mode is not used in servicing.Note: Never use it because user information will be deleted when Fac-
tory Reset is executed by touching the Start button of Factory Reset.
6-3. Diagnosis Function (Diag)
6-3-1. Diag1. NORWhen NOR on the screen is selected, and the EXEC button is touched, NOR fl ash memory (IC1504) is diagnosed.
When OK is displayed in the fi rst line, NOR fl ash memory (IC1505) is normal.When NG! is displayed in the fi rst line, NOR fl ash memory (IC1505) is abnormal.But NOR fl ash data is updated, it always show NG. Please ignore NG message.
Note: This test mode is for NV-U83/U93T, Refer to SUPPLEMENT-1 for NV-U83T.
-
NV-U83/U83T/U93T
13
2. moviNANDWhen moviNAND on the screen is selected, and the EXEC button is touched, NAND fl ash memory (IC2001) is diagnosed.
When OK is displayed in the last, NAND fl ash memory (IC2001) is normal.When NG! is displayed in the last, NAND fl ash memory (IC2001) is abnormal.But when software is updated, it always show NG. Please ignore NG message.
3. KEYWhen KEY on the screen is selected, and the EXEC button is touched, the [?/1] button of the main unit is diagnosed.
The check box of Power key reacts when the [?/1] button of the main unit is pressed. (The check box of Voice key doesnt react)
4. RDSWhen RDS on the screen is selected, and the EXEC button is touched, in the state of having connected the main unit with cradle (NVA-CU5T), device ID of RDS IC in the cradle is read.When U83 uses NVA-CU5T, this mode is possible.
When ID is OK is displayed, it is shown to be able to read device ID of RDS IC in the cradle. It is displayed at the error as Fail to Get RDS Chip ID.
5. GPSWhen GPS on the screen is selected, and the EXEC button is touched, GPS communication circuit is diagnosed.
When GPS test ...... OK is displayed, GPS communication cir-cuit is normal. It is displayed at the error as GPS test......Fail to open GPS device or GPS test......Fail to get GPS version.
6. BTWhen BT on the screen is selected, and the EXEC button is touched, BT version is displayed usually.
6-3-2. TP LEDThe current status of touch panel switch back light LED is dis-played. ON/OFF of touch panel switch back light LED is switched by touching the check box of ON and OFF.
6-3-3. BatteryThe voltage of the lithium battery of the main unit is displayed usually. It is displayed at the error as ---.
6-3-4. CDO1. ACCThe check box of ACC reacts when external power supply is sup-plied.
2. HeadPhoneThe check box of HeadPhone reacts when hedphone plug is in-serted.
6-4. LCD/Touch Panel Test (LCD)
6-4-1. LCD color setting1. RedWhen Red on the screen is selected, and the EXEC button is touched, red of the brightness max is displayed on full screen. To release from this mode, touch the screen.
-
NV-U83/U83T/U93T
14
2. GreenWhen Green on the screen is selected, and the EXEC button is touched, green of the brightness max is displayed on full screen. To release from this mode, touch the screen.
3. BlueWhen Blue on the screen is selected, and the EXEC button is touched, blue of the brightness max is displayed on full screen. To release from this mode, touch the screen.
4. White 100%When White 100% on the screen is selected, and the EXEC button is touched, white is displayed on full screen. To release from this mode, touch the screen.
5. White 0%When White 0% on the screen is selected, and the EXEC but-ton is touched, black is displayed on full screen. To release from this mode, touch the screen.
6. Color barWhen Color bar on the screen is selected, and the EXEC but-ton is touched, color bar is displayed on screen. To release from this mode, touch the screen.
7. Gray scaleWhen Gray scale on the screen is selected, and the EXEC button is touched, gradation (white 100% to 0%) is displayed on screen. To release from this mode, touch the screen.
8. GradationWhen Gradation on the screen is selected, and the EXEC but-ton is touched, gradation (blue 100% to 0%) is displayed on screen. To release from this mode, touch the screen.
9. ALLWhen ALL on the screen is selected, and the EXEC button is touched, above 1. Red is displayed on screen. Then whenever it touches the screen, it is displayed in order 2. Green 3. Blue 5. White 0% 6. Color bar 7. Gray scale 8. Gradation 4. White 100% LCD/touch panel test screen.6-4-2. Duty ratio up/downBacklight of screen can be adjusted.
6-4-3. Photo A/D valueA/D value of the photo sensor is displayed usually. It is displayed at the error as ---.
6-4-4. Touch panel1. TestThe Test button is touched, touch panel test screen is displayed.
200300
White point is displayed in the part touched on screen.The coordinates in the part touched at the last are displayed in the lower right of the screen.Value of upper: X axis (The left end is 0)Value of lower: Y axis (The up end is 0)To release from this mode, touch same point on the screen twice quickly.
2. Start CalibrationThe Calibration button is touched, touch panel test screen is dis-played. This mode is a mode adjusted to match the touch position to the screen coordinates.When test mode is set fi rst, this mode is performed. When the calibration fi le exists, the pop up screen of the confi rmation is dis-played. In that case, the calibration is begun when OK button is touched.
Touch for about three seconds the center of the target when this screen is displayed and then touch similarly because the next target is displayed.
When this screen is displayed, touch the screen and preserve the value in which the calibration is done. When not touching the screen for 30 seconds, the value in which the calibration is done is not preserved.
-
NV-U83/U83T/U93T
15
6-5. Audio Test (Audio)
6-5-1. Sine wave1. 100HzWhen 100Hz on the screen is selected, and the Play button is touched, 100 Hz sine curve is played. When the Stop button is touched, the audio output is stopped.
2. 500HzWhen 500Hz on the screen is selected, and the Play button is touched, 500 Hz sine curve is played. When the Stop button is touched, the audio output is stopped.
3. 1KHzWhen 1KHz on the screen is selected, and the Play button is touched, 1 kHz sine curve is played. When the Stop button is touched, the audio output is stopped.
4. 2KHzWhen 2KHz on the screen is selected, and the Play button is touched, 2 kHz sine curve is played. When the Stop button is touched, the audio output is stopped.
5. 5KHzWhen 5KHz on the screen is selected, and the Play button is touched, 5 kHz sine curve is played. When the Stop button is touched, the audio output is stopped.
6. Infi nityWhen Infi nity on the screen is selected, and the PLAY button is touched, output without audio is performed. When the Stop button is touched, the output is stopped.
7. SweepWhen Sweep on the screen is selected, and the Play button is touched, sine curve that changes continuously from 100 Hz to 5 kHz is played. When the Stop button is touched, the audio output is stopped.
6-5-2. VolumeAudio volume can be adjusted.
6-5-3. MicMicrophone volume can be adjusted. The purple shape show the volume size of input audio from mi-crophone.
6-6. GPS Test (GPS)
6-6-1. GPS InformationThe GPS Information button is touched, GPS information is dis-played on screen usually. It is displayed at the error as GPS port cant open or GPS read error. Note: Adjust Time button is not used in servicing.
Display Content DescriptionDate(UTC): UTC dateTIME: UTC timeN: North latitude (S: South latitude)E: East longitude (W: West longitude)Height: High degreeDir: DirectionSpeed: SpeedPDOP: Position DOP (DOP value is 0 to 10)HDOP: Horizontal DOP (DOP value is 0 to 10)VDOP: Vertical DOP (DOP value is 0 to 10)HPError: Not used in servicing
MODE:
Reception mode (2D: 2D measurement, 3D: 3D measurement, nofi x: non-mea-surement)Number in ( ) show detail (0: NO_FIX (nofi x), 1: SV1_FIX (nofi x), 2: SV2_FIX (nofi x), 3: SV3_FIX (2D), 4: ALL_IN_NEW (3D), 5: DL2 (2D), 6: DL3 (3D), 7: DR (nofi x), 8: JOHNNY_ERROR (nonfi x))
Number of satellites:
Left number that all satellites can be used in calculation (0 to 12)Right number that all satellites can be searched by this set (0 to 12)
-
NV-U83/U83T/U93T
16
6-6-2. G sensorThe G sensor button is touched, current real time G sensor data is displayed at the left on screen and G sensor data in g-calib.txt of NOR fl ash memory (IC1505) at the right on screen.
The Start button is touched, G sensor test screen is displayed. Then whenever it touches the screen, direction axis changes in or-der Y () Y (+) X () X (+) GPS test screen. (G sensor data is recorded in G-calib.txt of NOR fl ash memory (IC1505))
6-6-3. GyroThe value of the gyro is display at the right usually. It is displayed at the error as ---. (The value of the gyro (same numerical value) is displayed even if touching the Gyro button)The result of the gyro check (OK or NG) is displayed at the left after executing the G sensor.
6-6-4. Air PressureThe value of the atmospheric pressure is displayed usually. It is displayed at the error as ---. (The value of the atmospheric pres-sure (same numerical value) is displayed even if touching the Air Pressure button.
6-6-5. TemperatureThe value of the temperature is displayed usually. It is displayed at the error as ---. (The value of the temperature (same numerical value) is displayed even if touching the temperature button.
6-7. Cradle Test (Cradle)
6-7-1. CradleThe Cradle button is touched, A/D value for cradle ID distinc-tion is displayed on screen usually. It is displayed at the error as ---.
Connected Cradle A/D ValueCradle is not connected 4095TMC cradle (NVA-CU5T) About 1022Normal cradle (NVA-CU5) About 2088
6-7-2. BeaconThis mode is not used in this set.
6-7-3. CDO
1. ACCThe check box of ACC reacts when external power supply is sup-plied.
2. HeadPhoneThe check box of HeadPhone reacts when headphone plug is in-serted.
6-8. Bluetooth Test (BT)
-
NV-U83/U83T/U93T
17
6-8-1. Link TestThe start button is touched, microphone test, speaker/micro-phone test and RF power test is executed (Wait for a few minutes until the test result is displayed on the screen).
When OK is displayed in the for third line, microphone (MIC3501) is normal. When NG is displayed in the for third line, microphone (MIC3501) is abnormal. When OK is displayed in the for forth line, microphone (MIC3501) or speaker (SP3501) is normal. When NG is displayed in the for forth line, microphone (MIC3501) or speaker (SP3501) is abnormal. When OK is dis-played in the for seventh line, RF power is normal. When NG is displayed in the for seventh line, RF power is abnormal.
6-8-2. Device InfoThe Device Info button is touched, BD address and HCI version are displayed on the screen usually.
6-9. Firmware Update (FWUpdate)This mode is not used in servicing.
6-10. RDS Test (RDS)This mode is not used in servicing.
6-11. Movi Data Copy (Disk)This mode version is displayed on screen.
6-12. Log Display (Log)Test mode version is displayed on screen.
-
NV-U83/U83T/U93T
18
SECTION 5DIAGRAMS
5-1. BLOCK DIAGRAM - MEMORY/LCD/SENSOR Section -
MNAND_CLK
MD0 MD15
MA1 MA22
MNAND_DAT0 MNAND_DAT3
MA1 MA24
MD0 MD31
CPUIC1001 (1/3)
DATA
BUS
DATA BUS
ADDR
ESS
BUS
ADDRESS BUS
A20 P23MNAND_CMDB18
XRESET_OUTY21XOEAC5XWEAB5XCS0B3NOR_XWPAD5
MD0 MD31
XCE
DQ0 DQ15
A0 A21
NOR FLASH MEMORYIC1505
F1XWP/ACC B3
XOE G1XWE A4
XRESET B4
DAT0 DAT3
NAND FLASH MEMORYIC2001
CMD M5CLK M6
LED DRIVERIC3004
SHDN
VIN SWSYS3.2V 5 1FB3 3
4
MA1 MA24
MD0
MD1
5
MA10
MA
24
DQ0
DQ1
5
CLK
SDCL
K1
A0
A12,
BA0,
BA1
F2
AD7
CKE
SDCK
E
F3
AD6
XWE
F9
XCS
XSDC
S0
G9
AB7
XCAS
XSDC
AS
F7
AA6
XRAS
XSDR
AS
F8
AC7
LDQM
DQM0
E8
AB9
UDQM
DQM1
F1
AB10
DQM2
AC9
DQM3
AC10
SD-RAMIC1502
MD16
MD
31
MA10
MA
24
DQ0
DQ1
5
CLK
A0
A12,
BA0,
BA1
F2
CKE
F3
XWE
F9
A XRESET_OUT
XCS
G9
XCAS
F7
XRAS
F8
LDQM
E8
UDQM
F1
SD-RAMIC1503
: AUDIO
: VIDEO
SIGNAL PATH
LCD5001LIQUID
CRYSTALDISPLAY
LDD0 LDD4,LDD6 LDD15
R0 R7, G0 G7, B0 B7
HSYNCL_LCLK_A0
R23VSYNC
L_FCLK_RDP22
PCLKL_PCLK_WR
R21DE
L_BIAST24
PON
LED+LED
LCD_ON_CPU
A18PWM_OUT0
D3008
23 DOUT
24 DIN1 SCLK
B15SSPRXD
D16SSPTXDB16SSPSCLK
LEVEL SHIFTIC6002
LEVEL SHIFTIC9509
3 CSA17SSPSFRM LEVEL SHIFTIC9508
7AIN1+ 7 X_OUT9AIN2+ 6 Y_OUT
15AIN5+ATMOSPHERIC
SENSORIC9502
A/D CONVERTERIC9503
ACCELERATION SENSORIC9511
5AIN6+ 5 OUT11AIN3+ 6 V-REF
GYRO SENSORSE9501(NV-U83T)
(Page 19)
-
NV-U83/U83T/U93T
NV-U83/U83T/U93T
1919
5-2. BLOCK DIAGRAM - MAIN Section -
CP4001GPS MODULE
(GMX-040)
USB CONTROLLERIC4505
1 A21TXD_GPSGPS_IN FFRXDANT4001
INTERNALGPS ANTENNA
AUDIO CODEC,TOUCH SCREEN CONTROLLER
IC3501
BRIGHTDETECTQ4004
2 D19RXD_GPS FFTXD8 C161PPS GPS_1PPS7 F23MODE/RAMCLR GPS_RAM_CLEAR6 F22SYS RESET XGPS_RESET
5 SDATAOUT8 SDATAIN6 BITCLK10 SYNC46 PENDET11 RESETB
A22
C13
SDA
AC97_SDATA_OUT 37MONOOUT
41HPOUTR
39HPOUTL
30AUXADC
BATTERYCHECK
Q3501, 350231BMON
B13AC97_SDATA_IN_0
B10HP_XDET
A14AC97_BITCLKC12AC97_SYNCC10AC97_IRQ
14 X+/AUXL15 X/AUXR16 Y+/VIDL17 Y/VIDR
A13AC97_RESET_X
D14SP1_XMUTE
AA17HP_XMUTE
E22USBH_P1
D23USBH_N1
R22 43MSLED_EN GPIO0
8 FSDP
AC11MS_XINS
5D+ [1]
D20 SCL
AB14 RDS_XIRQ
A11 STD_TXD
CPUIC1001 (2/3)
CN6004 (1/2)
2
3
6
RDS_SDA
RDS_SCL
RDS_XIRQ
9 CRADLE_ID
FROM CRADLE(NVA-CU5/CU5T)
CN4003 (USB)
3
1
D+
56 D+ [0]
VBUS
X100113MHz
AC21AD21
P
X
T
A
L
_
O
U
T
P
X
T
A
L
_
I
N
X45016MHz
5049
X
T
A
L
O
U
T
X
T
A
L
I
N
X350124.576MHz
23
X
T
L
O
U
T
X
T
L
I
N
X250112MHz
43
X
O
X
I
12
P
C
B
E
E
P
T
X
T
A
L
_
O
U
T
T
X
T
A
L
_
I
N
X100232.768kHz
AA22AA23
TPS5001TOUCHPANEL
SWITCH
LINE AMPIC3503
POWER AMPIC3504 SP3501
DBATT_CHK
AXRESET_OUT
9 HSDP
6D [1]
24P0 [6]
18MS_D0
26MS_CLK
16MS_BS
22MS_XINS
25MS_3V3
CN9302(MEMORY STICK DUO)
4
8
2
9
DATA0
SCLK
BS
VCC
44XRST
6INS
J3501J
MUTINGQ3504
MUTINGQ3503
MUTING CONTROLSWITCH
Q3505 3507
BUFFERIC4001
SIGNALSELECTOR
IC4503
B11 STD_RXD
1 D [0]
51 VREF
E21 USB_ID
B22 USBC_P
AC19 USB_PUP
C20 USBC_N
C15 USB_XDET
2 D
4 ID
46 P1 [0]25 P0 [4]26 P0 [2]
SIGNALSELECTOR
IC4502D4004
7 FSDM6 HSDM
B VBUS
C USB_XCHGON, USB_HPWR, XACC_IN_HUB XACC_IN_HUBUSB_HPWRUSB_XCHGON
USB DETECTQ4002
17MS_D13DATA1
19MS_D25DATA2
23MS_D37DATA3
LED DRIVEQ2501
D2502(MEMORY STICK ACCESS)
MEMORY STICK CONTROLLERIC2501
: AUDIO
: FM
SIGNAL PATH
: NAVI
: USB
: MEMORY STICK
+3.3VREGULATOR
IC4501
R4010
MIC3501
22 MIC2
CP5501BLUETOOTH MODULE
15RESETB
ANT
20UART_RTS21UART_RX22UART_CTS23UART_TX
AD15 BT_XRESET
B20 BTCTSC22 BTTXDC19 BTRTSC21 BTRXD14
: BLUETOOTH OUT
: BLUETOOTH IN
: MIC
AT9001
Q5501
D5501(BLUETOOTH)
(Page 20)
(Page 20)
(Page 20)
(Page 18)
-
NV-U83/U83T/U93T
NV-U83/U83T/U93T
2020
5-3. BLOCK DIAGRAM - POWER SUPPLY Section -
CHARGE CONTROLIC3003
BVBUS
CN6004 (2/2)
9
10
11
CR_5VCR5V
CR_5V
XCRADLE_ON1
1XCRADLE_ON2
FROM CRADLE(NVA-CU5/CU5T)
D6002
D3016
D3007
D4005
Q4003
Y24XACC_IN
V22POWER_SW
C18XCRADLE_ON
AB6XBATT_CHG
W22XVDD_FAULT
AB15RDS_PWR_EN
AA24SYS_EN
Q3015
TU3.2V
B+ SWITCHQ3001
BAT3001LITHIUM ION
BATTERY
SYS5V
GPS3.3V
SWITCHINGQ3011, 3012
BU3V
11PROG
16NTCBAT
4IN1
2
OUT 3
SHDN 6
ACPR 13
WALL 5
15VNTC
1IN2
VOLTAGE DETECTIC3001
VOLTAGE DETECTQ3018
VOLTAGE DETECTQ3128
+3.2VREGULATOR
IC3007
AC17TPLED_ON
TPLED_5V B+ SWITCHQ3016, 3017
C11LCD3.2V_ON
LCD3.2V B+ SWITCHQ3009, 3010
SYS3V B+ SWITCHQ3007, 3008
+3.1V
MA+B
+3.1VREGULATOR
IC9510
+4.8V+4.8V
REGULATORIC9507
AB24XBATT_FAULT
DC/DCCONVERTER
IC3005
+3.3VREGULATOR
IC3505
D3003
D3023
D3004
D3006
D3009
D3005
D3014
B+ SWITCHQ3003-1, 3026
CHRG+B
B+ SWITCHQ3003-2
B+ SWITCHQ3002
+DC IN 5VJ3001
POWER CONTROLIC3002
VINDCDC3 5
VINDCDC1
VRTC
6DCDC1_EN 25
16
XPWRFAIL31XINT28
W23PWR_SDA
XRESET XRESPWRON27Y22SCLK30SDAT29
W21PWR_SCL
Y23PWR_EN
PWR_CORE L34VDCDC32
BU3V2 L235
XLOWBATT 21
VDCDC233
SYS3.2V L17VDCDC19
PWR1.1V VLDO218PWR1.3V VLDO120
CHRG
XACC_IN_HUB
14
SUSP7HPWR8
DCDC3_EN 23
VINLD0 19LDO_EN 22
VSYSIN 14
XHOT_RESET 11
VINDCDC2 36
D4002CHG
D BATT_CHK
C USB_XCHGON, USB_HPWR, XACC_IN_HUB
CPUIC1001 (3/3)
F3001
F3002
CHARGE CURRENTCONTROL SWITCH
Q3004, 3005
POWER OFFSWITCHQ3021
B+ SWITCHQ3006
S3002RESET
S3003I/
POWER SWITCHDETECTQ3024
POWER CONTROLQ3023
CHARGING(RED)
D9002
D4006CHG
FULL CHARGE(GRN)
TOUCH PANELSWITCH
BACK LIGHT
USB_HPWRUSB_XCHGON
+2.5VREGULATOR
IC3502MIC2.5V
(Page 19)
(Page 19)
(Page 19)
-
NV-U83/U83T/U93T
NV-U83/U83T/U93T
2121
For Schematic Diagrams.Note: All capacitors are in mF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics and tantalums.
All resistors are in and 1/4 W or less unless otherwise specifi ed.
f : internal component. C : panel designation. A : B+ Line. Power voltage is dc 3.7V and fed with regulated dc power
supply from battery connector (CN3001). Voltages and waveforms are dc with respect to ground
under no-signal conditions. no mark: TEST MODE (COLOR BAR) Voltages are taken with a VOM (Input impedance 10
M). Voltage variations may be noted due to normal production
tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production
tolerances. Circled numbers refer to waveforms. Signal path. F : AUDIO E : VIDEO f : FM j : NAVI N : USB P : MEMORY STICK a : BLUETOOTH OUT k : BLUETOOTH IN O : MIC
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.(In addition to this, the necessary note is printed in each block.)
Waveforms MAIN Board
X1002
500 mV/DIV, 10 s/DIV
30.5 s1 Vp-p
X1001
500 mV/DIV, 20 ns/DIV
76.9 ns1.1 Vp-p
IC3501 (XTLOUT)
1V/DIV, 20 ns/DIV40.7 ns
1.8 Vp-p
IC3501 (BITCLK)
2 V/DIV, 20 ns/DIV
81 ns4.1 Vp-p
IC2501 (XO)
2 V/DIV, 20 ns/DIV
83.3 ns3.4 Vp-p
For Printed Wiring Boards.Note: X : Parts extracted from the component side. Y : parts extracted from the conductor side. f : internal component. : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.)
Caution:Parts face side:(SIDE A)Pattern face side: (SIDE B)
Parts on the parts face side seen from the pattern face are indicated.Parts on the pattern face side seen from the parts face are indicated.
Lead layouts surface
CSP (Chip Size Package) Lead layout of conventional IC
Caution:Parts face side:(Conductor Side)Pattern face side: (Component Side)
Parts on the parts face side seen from the pattern face are indicated.Parts on the pattern face side seen from the parts face are indicated.
ANT, MAIN and SENSOR boards are multi-layer printed board.
However, the patterns of intermediate-layer have not been included in diagram.
The voltage and waveform of CSP (chip size package) cannot be measured, because its lead layout is different from that of conventional IC.
-
NV-U83/U83T/U93T
NV-U83/U83T/U93T
2222
5-4. PRINTED WIRING BOARDS - MAIN Section (1/2) - : Uses unleaded solder.
+
++
D
+
FB6010
CN4007
R3033
R3034
C1507
R
3
0
3
7
C1508
R3038
C4003
C
3
0
6
4
R
B
2
0
0
1
C4005
RB2002
C4006Q4004
C1510
C3068
C4009
R3041
C3069
C1512
R
3
0
4
2
C1514
C1515
R3046
F3002
C1517
R3047
C4010
R3048
C4011
C1519
C4013
C1520
C
1
5
2
2
R3052
R3054
R
1
1
1
4
R
1
1
1
5
R
3
0
5
6
R
3
0
5
7
R3058
R1120R1121
R3061
R3062
R1122
T
P
3
5
0
7
R3065 R3066
R4008
I
C
4
0
0
1
FL3001
FL3002
FL3003
FL3004
FL3005
R3075
R
3
0
7
6
R3083
R3084
C
N
2
5
0
1
R
4
0
2
6
R3087
R3088
CN5001
CN5003
C2501
C2503
C
2
5
0
4
Q2501
FB2001
C2506
C
2
5
0
7
C
2
5
0
8
C2509
C2511
D2502
R2501
R
2
5
0
2
R2503
R2505
D5001
R2506
R2507
IC2501
R2509
FL4001
R
2
5
1
9
R2520
R2526
V
D
5
0
0
1
VD5002VD5003
VD5004
CN3502
CN6001
CN6004
C3501C3502
C3503
C3504
Q3501
C3505FB3001
Q3502
C3506C3507
Q
3
5
0
3
Q
3
5
0
4
C3508
C3509
C6002
C
3
5
1
0
C3511
C
3
5
1
3
Q
3
1
2
8
R3106
C3517
C
3
5
1
8
C3519
R3109
C6014
C6015
R3110
C3522
C3523
C3524
D3501
C
3
5
2
5R3115
C
3
5
2
6
D
3
5
0
2
C3527
C3528
C3529
R
3
5
0
1
R
3
5
0
2
R3503R3504
L3001
R3506
L3003
C3530
R3508
L3005
C3531
IC3501FL2501
IC3503
C3533
R3123
IC3504
C3534
IC3505
C3535C3536
R
3
1
2
6
C3537C3538
R3510
IC6002
R3512
C1024
C
1
0
2
5
C3541
R3519
R3131
C1026
C3543
C1027
C
1
0
2
8
C
3
5
4
4
C3545
C
1
0
2
9
C3546
C3547
R1003
C
3
5
4
8
R6018
R3520
C
3
5
4
9
R6019
R3521
TP3002R1006
R
1
0
0
7
R3523
TP3003
R1008
V
D
3
5
0
4
VD3502
V
D
3
5
0
3
C
1
0
3
0
R3524
TP3004
R1009 C1031
VD3505
R3525
C
1
0
3
2
VD3506
R3526
C1033
R3527
VD3507
C
3
5
5
0
C1034
R3528
VD3508
C3551
C1035
R3529
C3552
C
1
0
3
6
C
3
5
5
3
C
1
0
3
7
C
1
0
3
8
VD6004
C3554
C3555
VD6005
R1012
C
3
5
5
6
R3530
VD3510
R3531
VD3511
R1015
R
3
5
3
2
R1016
R3533
R
1
0
1
7
C1040
FB1501
R3535
C1041
C1042C1043
R3538
C3560
R3539
C1045
C
3
5
6
1
C1046
C
3
5
6
2
C1047
C3563
R1020
C
3
5
6
4
C1049
R
1
0
2
2
FB4002
FB4003
R3540
R1024
FB4004
R3541
R1025
F
B
4
0
0
5
R
1
0
2
6
FB4006
R1027
F
B
4
0
0
7
R
1
0
2
8
FB4008
R
1
0
2
9
R3546R3547
R3549
R1030
R
1
0
3
1
R
1
0
3
3
R3550
C
2
0
0
2
C2003
C2004
C
2
0
0
5
C
2
0
0
7
C2013C2014
FL3501
FL6001
FL6002
R
1
0
5
9
X2501
R
1
0
6
0
R2002
R
1
0
6
3
R2003R2004
R
1
0
6
5
R2005
R
1
0
6
6
R
1
0
6
9
R2006R2007R2008R2009
IC2001
FL1001
R
1
0
7
1
R
2
0
1
1
R1072
R
1
0
7
3
R2013
R1078
FB2501
F
B
2
5
0
2
F
B
2
5
0
3
F
B
2
5
0
4
F
B
2
5
0
5
FB2506
FB2507
R
1
0
9
3
R
1
0
9
4
R
1
0
9
5
R1096
R1097
C3004
Q3001
C
3
0
0
5
Q
3
0
0
2
C
3
0
0
7
Q
3
0
0
3
C
3
0
0
8
Q3004
C3009
Q3005
Q
3
0
0
6
C
3
0
1
0
C
3
0
1
1
C3013
C3014
Q3011
C3015
Q3012
C3016
C
3
0
1
7
C3018
C
3
0
1
9
Q3018
C
3
0
2
0
C
3
0
2
1
C3022
C
3
0
2
3
X3501
C3025
C3026
D3002
D3003
C
3
0
2
7
D3004
C
3
0
2
9
D3005
Q3026
D3006
TP2506
D3007
D
3
0
0
9
C
3
0
3
0
IC3001
C
3
0
3
2
IC3002
C3033
IC3003
IC3005
R3010
C3039
R3011R3012
D3016
R3013
R3014
R3015
C
3
0
4
0
R3018
R3019
F
B
3
5
0
1
F
B
3
5
0
2
F
B
3
5
0
3
F
B
3
5
0
4
D3020
D
3
0
2
1
F
B
3
5
0
6
C
3
0
4
6
FB3507
D3023
C3047
F
B
3
5
0
8
C3049
R3021
FB6001
R3022
F
B
6
0
0
2
R3023
FB6003
R3024
FB6004
F
B
6
0
0
5
R3026
S3002
FB6006
S3003
FB6007
R3028
FB6008
R3029
FB6009 CN4003
R5004R5003
R
5
0
0
2
R5001
F
B
9
5
0
5
IC9509 C9526
TP9504R9504
C9505
IC9510R9503
C9521JL9503
F
B
9
5
0
4
IC9508
C
9
5
1
0
C9529C9518
IC9503
C9513
R9506
C9515
F
B
9
5
0
6
C9519
JL9502
F
B
9
5
0
3
IC9507
JL9501
FB9501
CN9503
C9507
C9512
R9514 TP9502
C
9
5
0
6
TP9503C9511
TP9505C9503
R
9
5
1
3
TP9501
IC9502
C9501
R
9
5
1
2
TP9506
C
9
5
0
9IC9511
D9501
+
C
3
5
4
2
C3557IC3502
CN3501
MIC3501
54
1
1
0
481
12 13
3736
2425
49
1 2 345
4
5
543
S
G
S
1 234
1 1040
41
17
611
1
8
13
1
1
0
18
1
2
C
B
E
K
KA
K
K
481
12 13
3736
2425
1
2
18
111
CB E
DG S
C
B
E
49
12
25
1
3624 37
1348
1 2 345
B1C1
A1B3A3
C3B2C2
A2
1
2
3
154
3
M6
A7
E7
M7
A11B2
F5
A1B1C1D1E1F1G1H1J1K1L1
A6
E6
A8
E8
M1N1P1
A2
G5H5J5K5M5 M8
A9
E9
M9
A10
E10
M10M11
A12
E12F12G12H12J12K12L12
A13 A14A3 A4 A5
E5
N6N7N5 N8N9 N10 N11P6 P7P5 P8 P9 P10 P11
C11C6 C8C7 C9 C10C5B11B6 B8B7 B9 B10B5
E13F13G13H13J13K13L13
E14F14G14H14J14K14L14
M12N12P12
M13N13P13
D12C12B12
D13C13B13
D14C14B14
M14N14P14
M4N4P4
M3N3P3
M2N2P2
E3F3G3H3J3K3L3
E2F2G2H2J2K2L2
D4C4B4
D3C3B3
D2C2
F10G10H10J10
K7K6 K8 K9 K10
8
1
5 4
C
B
E
C
B
E
8
1
5 4
DG
C E
D GS
C
B
E
A AKAA K
D
A
A
K
11
20213031
41
1 45
817
13
16
912
5
61011
1
AA K
1 5
AANT BOARD
BMS DUOBOARDCN9301MAIN BOARD (COMPONENT SIDE)
1-873-803-
11
(11)
SP3501
CP4001GPS
MODULE
ANT4001INTERNAL
GPSANTENNA
E E
TPS5001TOUCHPANEL
SWITCH
MEMORYSTICK
ACCESS
TOCRADLE
(NVA-CU5/CU5T)
13
64
1
3
6
4
(USB)RESET
581
2
34
5
58
1
2
34
5
24
1312
1
1 4
58
1 4
58
SENSOR BOARD (COMPONENT SIDE)
1-873-804-
11
(11)
8
7
6
5
1
2
3
4
8
7
6
5
1
2
3
4
1
7
26
35
4
8 18
+
+
+1-873-804-
11
(11)
SENSOR BOARD (CONDUCTOR SIDE)
A
B
C
D
E
F
G
H
1 2 3 4 5 6 7 8 9 10 11 12 13 14
1
3 4
5
1
2
Note 1: When the MAIN board is exchanged, the writing work of data is necessary. Confi rm details to each service headquarters.
Note 3: IC2001, IC3002, IC3003, IC3501 on the MAIN board and IC9511 on the SENSOR board cannot exchange with single. When IC2001, IC3002, IC3003, IC3501 on the MAIN board and IC9511 on the SENSOR board are damaged, exchange the entire mounted board.
(Page 27)
(Page 27)
Note 2: When the SENSOR board is exchanged, the G sensor caribration is necessary. Confi rm details to each service headquarters.
Ref. No. Location
Semiconductor Location
D2502 H-9 D3002 G-11 D3003 H-10 D3004 H-11 D3005 G-9 D3006 G-8 D3007 G-10 D3009 G-11 D3016 H-8 D3020 H-11 D3021 H-10
Ref. No. Location D3023 G-11 D3501 E-12 D3502 F-11 D5001 H-11 D9501 D-3
IC2001 D-13 IC2501 E-13 IC3001 G-11 IC3002 D-11 IC3003 G-10
Ref. No. Location IC3005 B-12 IC3501 F-12 IC3502 F-11 IC3503 B-11 IC3504 B-11 IC3505 F-13 IC4001 B-11 IC6002 H-5 IC9502 F-3 IC9503 D-2 IC9507 E-5
Ref. No. Location IC9508 E-4 IC9509 E-4 IC9510 E-5 IC9511 F-3
Q2501 G-10 Q3001 H-7 Q3002 H-6 Q3003 H-10 Q3004 G-11 Q3005 G-10
Ref. No. Location Q3006 G-10 Q3011 B-11 Q3012 B-11 Q3018 F-11 Q3026 H-11 Q3128 H-11 Q3501 G-12 Q3502 G-12 Q3503 H-13 Q3504 H-12 Q4004 A-11
-
NV-U83/U83T/U93T
NV-U83/U83T/U93T
2323
5-5. PRINTED WIRING BOARD - MAIN Section (2/2) - : Uses unleaded solder.
+
DG S
D
G
S
DG SC
3
0
5
8
C1501
C3059
R3031
R3032
C1504
R3035
FB1003
C
3
0
6
0
C3061
C3062
Q4002
Q4003
R1100R1101R1102
R3043R
1
1
0
3
R3044
F3001
R3045
R1105
R1108
R
1
1
0
9
C
4
0
1
2
R1110
R1111
R1116R1117
R1501
R1502
R1504
X4501 D4002
D4003
D4004
D
4
0
0
5
IC1502
D4006
IC1503
R4004
IC1505
R4009
FL3006
R3070
R4010
R3071
R4011
R3072
R3074
R4015
R4016
R3077
R3078
TP1001TP1002
R3081
R
3
0
8
2
R4025
R3085
R
3
0
8
6
R4027R4028
CN5002
R3092
R3095
R3098
C5004C5005
TP1030
TP1031
JL3501
JL3502
JL3503
JL3504
JL3505
J
L
3
5
0
6
JL6001
JL6002
JL3510
JL3511
TP1057
Q3505
Q3506
Q3507
JL1028
R
3
1
0
0
JL1029
C6010C6011
C6012
C1001
R3114
D
3
5
0
3
R
3
1
1
7
R
3
1
1
8
D
6
0
0
2
L3002
VD6007
R3120
D6004
R3121
L3006
R1001
TP3001
IC1001
R6020R6021
VD3509
J3501
V
D
6
0
0
1
R6022
V
D
6
0
0
2
V
D
6
0
0
3
R
6
0
2
3
R1010
R
6
0
2
4
R1011C1039 R 1
0
1
3
R1014
C3559
R3536
R3537
C1044
C
4
5
0
1C4502
C4503
C1048
C4504
R
1
0
2
1
C4505C4506
LF3001
R
3
5
4
4
R
3
5
4
8
R1032
R1034
R1035
R
1
0
3
8
R1039
C2006
R1040
D4501
R1041
R1042R1043
R1044
R1045
R1046R1047
R1048
R
4
5
0
4
C2011
R4505
R1049C2012
R
4
5
0
7
IC4501
IC4502
IC4503
R1050
IC4505
R1052R1053
R
1
0
5
4
R1055
R
4
5
1
2
R
1
0
5
7
R4514
TP1501
JL3001
JL3002
JL3003
JL3004
R4525
JL3005
JL3006
R4526
R4527
JL3007
JL3008
JL3009
R1074
JL3010
R1075
JL3011
JL3012
R1076
JL3013
JL3014
JL3015
JL3016
JL3017
JL3018
JL3019
R1080
R
1
0
8
1
FB5001
R
1
0
8
2
R
1
0
8
3
R
1
0
8
4 JL3020
R
1
0
8
5
JL3021
R
1
0
8
6
JL3022
JL3023
R
1
0
8
7
R
1
0
8
8
JL3024
R
1
0
8
9
JL3025
JL3026
J
L
3
0
2
7
J
L
3
0
2
8
JL3029
CN3001
R
1
0
9
0
R
1
0
9
1
JL3030
JL3031JL3032
R1099
C
3
0
0
1
C
3
0
0
2
RB1001
RB1002
RB1003
RB1004
RB1005RB1006 RB1007
Q3007
RB1008
Q3008RB1009
Q3009
RB1010
Q3010
RB1011 RB1012
RB1013
RB1014
RB1015
Q3015
RB1016
Q3016
RB1017
Q3017
Q3021
Q3023
Q3024
D3008
JL4001
JL4002
JL4003
JL4004
JL4005
C
3
0
3
1
JL4006
JL4007
JL4008
IC3004C3034
C3035
JL4009
C
3
0
3
6
C3037
IC3007
D3014
D
3
0
1
8
JL4010
JL4011
D3019
J
L
4
0
1
2
JL4013
R3016
JL4014
JL4015
X1001
C3041
JL4016
X1002
C
3
0
4
2
JL4017
JL4018
JL4019
C
3
0
4
8
RB4501
R
B
4
5
0
2
JL4020
JL4021JL4022
JL4023JL4024
C3057
Q5501
R5521
D5501
C5507
C5502
C5503
C5501 C5504
R5518
CP5501
R5526L5502
R5523
R5524
CN5501
A1B1C1D1E1F1G1H1J1
A2B2C2D2E2F2G2H2J2
A3B3C3D3E3F3G3H3J3
A7B7C7D7E7F7G7H7J7
A8B8C8D8E8F8G8H8J8
A9B9C9D9E9F9G9H9J9
A1B1C1D1E1F1G1H1J1
A2B2C2D2E2F2G2H2J2
A3B3C3D3E3F3G3H3J3
A7B7C7D7E7F7G7H7J7
A8B8C8D8E8F8G8H8J8
A9B9C9D9E9F9G9H9J9
1 45
4 5
57
4342
2928
1415
156
DG S
S
G S GS
1
2
3
5
CB E
C BE
AA K
A1 A2 A3 A4 A5 A6B1 B2 B3 B4 B5 B6C1 C2 C3 C4 C5 C6D1 D2 D3 D4 D5 D6E1 E2 E3 E4 E5 E6F1 F2 F3 F4 F5 F6G1 G2 G3 G4 G5 G6H1 H2 H3 H4 H5 H6
1 45
C
B
E
D GSC BE
K
KA
K
K
AB17 AC17 AD17A18B18C18D18AA18AB18AC18AD18A19B19C19D19AA19AB19AC19AD19A20B20C20D20AA20AB20AC20AD20A21B21C21D21E21F21G21H21J21K21L21M21N21P21R21T21U21V21W21Y21AA21AB21AC21AD21A22B22C22D22E22F22G22H22J22K22L22M22N22P22R22T22U22V22W22Y22AA22AB22AC22AD22A23B23C23D23E23F23G23H23J23K23L23M23
C1D1E1F1G1H1J1K1L1M1N1P1R1T1U1V1W1Y1AA1AB1AC1AD1A2B2C2D2E2F2G2H2J2K2L2M2N2P2R2T2U2V2W2Y2AA2AB2AC2AD2A3B3
K13
C3D3E3F3G3H3J3K3L3M3N3P3R3T3U3V3W3Y3AA3AB3AC3AD3A4B4C4D4E4F4G4H4J4K4L4M4N4P4R4T4U4V4W4Y4AA4AB4AC4AD4A5B5C5D5AA5AB5AC5AD5A6B6C6D6
AA17
AA6AB6AC6AD6A7B7C7D7AA7AB7AC7AD7A8B8C8D8AA8AB8AC8AD8A9B9C9D9AA9AB9AC9AD9A10B10C10D10K10L10M10N10P10R10AA10AB10AC10AD10A11B11C11D11K11L11M11N11P11R11AA11AB11AC11AD11A12B12C12
A1B1
D12K12L12M12N12P12R12AA12AB12AC12AD12A13B13C13D13L13M13N13P13R13AA13AB13AC13AD13A14B14C14D14K14L14M14N14P14R14AA14AB14AC14AD14A15B15C15D15K15L15M15N15P15R15AA15AB15AC15AD15A16B16C16D16AA16AB16AC16AD16A17B17C17D17
N23P23R23T23U23V23W23Y23AA23AB23AC23AD23A24B24C24D24E24F24G24H24J24K24L24M24N24P24R24T24U24V24W24Y24AA24AB24AC24AD24
A AK123
4 5
1
2
3
45
6
7
8
12345 6 7 8
15
D G
D
DG S
D
1
6
3
4
D
G
S
A K
123
4 5
1
2
3 4
MAIN BOARD (CONDUCTOR SIDE)
1-873-803-
11
(11)
J
LCD5001LIQUID
CRYSTALDISPLAY
BAT3001LITHIUM ION BATTERY
DC IN 5V +
J3001 CHGCHARGING
(RED)
CHGFULL CHARGE
(GRN)
A
B
C
D
E
F
G
H
1 2 3 4 5 6 7 8 9 10 11 12 13 14
E BC
(BLUETOOTH)
28 24
29 3130 32
23
151410
9
1
CANT BOARD
Note 1: When the MAIN board is exchanged, the writing work of data is necessary. Confi rm details to each service headquarters.
Note 2: IC1001, IC1502, IC1503, IC1505, IC4502, IC4503 and IC4505 on the MAIN board cannot exchange with single. When IC1001, IC1502, IC1503, IC1505, IC4502, IC4503 and IC4505 on the MAIN board are damaged, exchange the entire mounted board.
(Page 27)
Ref. No. Location Semiconductor Location
D3008 E-5 D3014 A-4 D3018 C-4 D3019 E-2 D3503 G-3 D4002 H-13 D4003 A-2 D4004 G-9 D4005 H-13 D4006 H-13 D4501 G-5
Ref. No. Location D5501 H-12 D6002 H-7 D6004 H-6
IC1001 D-3 IC1502 B-3 IC1503 B-2 IC1505 B-4 IC3004 E-5 IC3007 H-6 IC4501 G-3
Ref. No. Location IC4502 G-5 IC4503 H-5 IC4505 G-4
Q3007 C-5 Q3008 C-5 Q3009 E-2 Q3010 E-2 Q3015 H-5 Q3016 C-5 Q3017 D-5
Ref. No. Location Q3021 H-12 Q3023 G-12 Q3024 A-3 Q3505 H-3 Q3506 G-3 Q3507 G-3 Q4002 G-3 Q4003 H-12 Q5501 H-12
-
NV-U83/U83T/U93T
NV-U83/U83T/U93T
2424
5-6. SCHEMATIC DIAGRAM - MAIN Section (1/10) - See page 21 for Waveforms. See page 40 for IC Pin Function Description.
(2/10)BOARDMAIN
14
(2/10)BOARDMAIN
15
(2/10)BOARDMAIN
16
(9/10)BOARDMAIN
11
(3/10)BOARDMAIN
2
(4/10)BOARDMAIN
1
13MAIN
BOARD(7/10)
12MAIN
BOARD(8/10)
3(6/10)
BOARDMAIN
4(10/10)BOARDMAIN
5(10/10)BOARDMAIN
6(5/10)
BOARDMAIN
8(8/10)
BOARDMAIN
9(9/10)
BOARDMAIN
10(9/10)
BOARDMAIN
1
2RTPXA270C5C520
IC1001
D
6MA25
C
4MA24
D
4MA23
C
2MA22
D
2MA21
E
4MA20
E
3MA19
C
1MA18
D
1MA17
F
3MA16
G
4MA15
F
2MA14
E
1MA13
G
3MA12
G
2MA11
H
3MA10
H
2MA9
G
1MA8
J
3MA7
J
2MA6
K
3MA5
K
2MA4
J
1MA3
K
4MA2
A
6MA1
C
6MA0
L
2MD31
M
2MD30
M
3MD29
N
2MD28
N
1MD27
P
3MD26
R
3MD25
R
1MD24
T
1MD23
V
2MD22
U
4MD5
Y
2MD4
Y
3MD3
A
A
3
MD2
A
B
1
MD1
A
B
4
MD0
A
C
5
XOE
A
B
5
XWE
A
C
7
XSDRAS
A
A
6
XSDCAS
A
B
9
DQM0
A
B
1
0
DQM1
A
C
9
DQM2
A
C
1
0
DQM3
A
B
7
XSDCS0
A
B
8
XSDCS1
A
D
6
SDCKE
A
C
4
SDCLK0
A
D
7
SDCLK1
A
D
3
SDCLK2
C
9RD/XWR
B
3XCS0
A
3XCS1
B
9RDY
A
B
6
XBATT_CHG
A
D
5
NOR_XWP
B
6XCS5
A
1
0
XPWE
B
7XCS2
C
8XCS3
C
7XCS4
A
C
1
3
XPOE
A
B
1
3
XPIOIR
A
D
1
3
XPIOIW
A
C
1
4
WLAN_SCLK
A
B
1
4
RDS_XIRQ
AA10
X
P
R
E
G
AB11
X
P
W
A
I
T
AC11
M
S
_
X
I
N
S
AB12
W
L
A
N
_
S
R
X
D
AD9
G
P
I
O
8
2
AD10
W
L
A
N
_
S
F
R
M
AA11
C
I
F
_
F
V
AC12
C
I
F
_
L
V
T24
L
C
D
_
O
N
_
C
P
U
R22
M
S
L
E
D
_
E
N
G24
L
D
D
0
G22
L
D
D
1
G23
L
D
D
2
H24
L
D
D
3
H22
L
D
D
4
H23
L
D
D
5
J22
L
D
D
6
K24
L
D
D
7
K22
L
D
D
8
K23
L
D
D
9
L21
L
D
D
1
0
L23
L
D
D
1
1
M24
L
D
D
1
2
L22
L
D
D
1
3
N24
L
D
D
1
4
M22
L
D
D
1
5
R23
L
_
F
C
L
K
_
R
D
P23
L
_
L
C
L
K
_
A
0
P22
L
_
P
C
L
K
_
W
R
R21
L
_
B
I
A
S
N22
L
D
D
1
6
N23
L
D
D
1
7
C11
L
C
D
3
.
2
V
_
O
N
B10
H
P
_
X
D
E
T
C10
A
C
9
7
_
I
R
Q
A18
P
W
M
_
O
U
T
0
C16
G
P
S
_
1
P
P
S
D13
V
O
I
C
E
_
S
W
B16
S
S
P
S
C
L
K
A17
S
S
P
S
F
R
M
D16
S
S
P
T
X
D
B15
S
S
P
R
X
D
C15
U
S
B
_
X
D
E
T
A14
A
C
9
7
_
B
I
T
C
L
K
B13
A
C
9
7
_
S
D
A
T
A
_
I
N
_
0
C13
A
C
9
7
_
S
D
A
T
A
_
O
U
T
C12
A
C
9
7
_
S
Y
N
C
A20
M
N
A
N
D
_
C
L
K
A21
F
F
R
X
D
B19
M
S
C
_
P
W
R
O
N
C14
W
L
A
N
_
X
I
R
Q
A15
W
L
A
N
_
X
P
D
B14
W
L
A
N
_
X
R
E
S
E
T
D19
F
F
T
X
D
D14
S
P
1
_
X
M
U
T
E
L
1MD14
V
3MD6
K
1MD15
U
1MD7
A
A
4
MD16
T
3MD8
A
B
3
MD17
R
4MD9
A
A
1
MD18
P
4MD10
Y
1MD19
P
2MD11
W
1MD20
N
3MD12
V
1MD21
M
4MD13
C18
X
C
R
A
D
L
E
_
O
N
C21
B
T
R
X
D
C22
B
T
T
X
D
B20
B
T
C
T
S
C19
B
T
R
T
S
B11
S
T
D
_
R
X
D
A11
S
T
D
_
T
X
D
C23
B
A
T
T
_
K
I
L
L
D22
W
L
A
N
_
S
T
X
D
A19
M
N
A
N
D
_
D
A
T
0
AB19
C
I
F
_
D
D
6
AD19
C
I
F
_
D
D
5
AA18
C
I
F
_
D
D
4
AC19
U
S
B
_
P
U
P
AA17
H
P
-
X
M
U
T
E
AD18
C
I
F
_
D
D
0
AB18
A
N
T
_
B
T
S
E
L
_
P
AC18
A
N
T
_
B
T
S
E
L
_
N
AC17
T
P
L
E
D
_
O
N
AB17
X
P
C
E
1
AC16
C
I
F
_
D
D
3
AD15
B
T
_
X
R
E
S
E
T
AB16
X
P
C
E
2
AB15
R
D
S
_
P
W
R
_
E
N
AC15
M
N
A
N
D
_
P
R
O
G
AD14
C
I
F
_
D
D
7
D17
M
N
A
N
D
_
D
A
T
1
B17
M
N
A
N
D
_
D
A
T
2
C17
M
N
A
N
D
_
D
A
T
3
B18
M
N
A
N
D
_
C
M
D
A13
A
C
9
7
_
R
E
S
E
T
_
X
D24
C
I
F
_
D
D
1
D
2
0
SCL
A
2
2
SDA
B
2
2
USBC_P
C
2
0
USBC_N
E
2
2
USBH_P1
D
2
3
USBH_N1
F
2
2
XGPS_RESET
F
2
3
GPS_RAM_CLEAR
E
2
3
UIO
V
2
2
POWER_SW
Y
2
4
XACC_IN
W
2
1
PWR_SCL
W
2
3
PWR_SDA
U
2
2
GPIO9
V
2
3
LAN_INT
W
2
4
CLK_REQ
Y
2
2
XRESET
Y
2
1
XRESET_OUT
A
B
2
3
BOOT_SELY
2
3
PWR_ENA
B
2
4
XBATT_FAULT
W
2
2
XVDD_FAULT
A
A
2
4
SYS_EN
A
B
2
1
PWR_CAP0
A
D
2
2
PWR_CAP1
A
C
2
2
PWR_CAP2
A
A
2
0
PWR_CAP3
U
2
1
XTRST
U
2
3
TDI
V
2
4
TDO
T
2
1
TMS
T
2
2
TCK
T
2
3
TESTCLK
A
C
2
1
PXTAL_IN
A
D
2
1
PXTAL_OUT
A
A
2
2
TXTAL_IN
A
A
2
3
TXTAL_OUT
A
B
2
2
PWR_OUT
A
B
2
0
VCC_BATT
A
1
2
VCC_IO
A
D
1
7
VCC_IO
A
1
6
VCC_IO
D
1
1
VSS_IO
A
A
1
9
VSS_IO
D
1
5
VSS_IO
N
2
1
VSS_IO