sp101 - murdercube manuals/ruger sp101.pdf · can operate firearms that can cause severe ... reach...
TRANSCRIPT
INSTRUCTIONMANUAL
FOR
RUGER® SP101®
DOUBLE ACTION REVOLVER
For Product Service on This Model Please Call:(603) 865-2442 (See p. 25)
STURM, RUGER & Company, Inc.Southport, Connecticut 06890 U.S.A.
THIS INSTRUCTION MANUAL SHOULD ALWAYS ACCOMPANY THIS FIREARM AND BETRANSFERRED WITH IT UPON CHANGE OF OWNERSHIP, OR WHEN THE FIREARM IS LOANED OR
PRESENTED TO ANOTHER PERSON.
KW/9-02 CR12
READ THE INSTRUCTIONS ANDWARNINGS IN THIS MANUAL CAREFULLYBEFORE USING THIS FIREARM
STAINLESSSTEEL
CALIBERS.357, .38 SPECIAL
9mm, .22 & .32
3
WARNING
“Children are attracted to andcan operate firearms that cancause severe injuries or death.Prevent child access by alwayskeeping guns locked away andunloaded when not in use. If youkeep a loaded firearm where achild obtains and improperly usesit, you can be fined or sent toprison.”
ADVERTENCIA
State-By-State WarningsCertain states require by law that their own specified warningnotices in larger-than-normal type be conspicuously included bythe manufacturer, distributor, or retail dealer with firearms soldin that state. Sturm, Ruger sells its products in compliance withapplicable laws and regulations. Because our products may besold in these states, we include the following:
California:
“A los niños los atraen las armasde fuego y las pueden hacerfuncionar. Ellos pueden causarseslesions graves y la muerte. Eviteque los niños tengan accesso a lasarmas de fuego guardándolassiempre con llave y descargadascuando no las esté utilizando. Siusted tiene un arma de fuegocargada en un lugar en que unniño tiene acceso a ella y la usaindebidamente, le pueden dar unamulta o enviarlo a la carcel.”
Connecticut:“UNLAWFUL STORAGE OF A LOADED FIREARM MAYRESULT IN IMPRISONMENT OR FINE.”
Florida:“IT IS UNLAWFUL, AND PUNISHABLE BYIMPRISONMENT AND FINE, FOR ANY ADULT TOSTORE OR LEAVE A FIREARM IN ANY PLACE WITHINTHE REACH OR EASY ACCESS OF A MINOR UNDER 18YEARS OF AGE OR TO KNOWINGLY SELL OROTHERWISE TRANSFER OWNERSHIP OR POSSESSIONOF A FIREARM TO A MINOR OR A PERSON OFUNSOUND MIND.”
Maine:“ENDANGERING THE WELFARE OF A CHILD IS ACRIME. IF YOU LEAVE A FIREARM AND AMMUNITIONWITHIN EASY ACCESS OF A CHILD, YOU MAY BESUBJECT TO FINE, IMPRISONMENT OR BOTH. KEEPFIREARMS AND AMMUNITION SEPARATE. KEEPFIREARMS AND AMMUNITION LOCKED UP. USETRIGGER LOCKS.”
Maryland:“WARNING: Children can operate firearms which may causedeath or serious injury. It is a crime to store or leave a loadedfirearm in any location where an individual knew or shouldhave known that an unsupervised minor would gain access tothe firearm. Store your firearm responsibly!”
Massachusetts:“WARNING FROM THE MASSACHUSETTS ATTORNEYGENERAL: This handgun is not equipped with a device thatfully blocks use by unauthorized users. More than 200,000firearms like this one are stolen from their owners every yearin the United States. In addition, there are more than athousand suicides each year by younger children andteenagers who get access to firearms. Hundreds more die fromaccidental discharge. It is likely that many more childrensustain serious wounds, or inflict such wounds accidentally onothers. In order to limit the chance of such misuse, it isimperative that you keep this weapon locked in a secure placeand take other steps necessary to limit the possibility of theftor accident. Failure to take reasonable preventive steps mayresult in innocent lives being lost, and in some circumstancesmay result in your liability for these deaths.”
“IT IS UNLAWFUL TO STORE OR KEEP A FIREARM,RIFLE, SHOTGUN OR MACHINE GUN IN ANY PLACEUNLESS THAT WEAPON IS EQUIPPED WITH ATAMPER-RESISTANT SAFETY DEVICE OR IS STOREDOR KEPT IN A SECURELY LOCKED CONTAINER.”
4
New Jersey:“IT IS A CRIMINAL OFFENSE TO LEAVE A LOADEDFIREARM WITHIN EASY ACCESS OF A MINOR.”
New York City:
“THE USE OF A LOCKING DEVICE OR SAFETY LOCK ISONLY ONE ASPECT OF RESPONSIBLE WEAPONSSTORAGE. ALL WEAPONS SHOULD BE STOREDUNLOADED AND LOCKED IN A LOCATION THAT ISBOTH SEPARATE FROM THEIR AMMUNITION ANDINACCESSIBLE TO CHILDREN AND ANY OTHERUNAUTHORIZED PERSONS.”
North Carolina:“IT IS UNLAWFUL TO STORE OR LEAVE A FIREARMTHAT CAN BE DISCHARGED IN A MANNER THAT AREASONABLE PERSON SHOULD KNOW IS ACCESSIBLETO A MINOR.”
Texas:“IT IS UNLAWFUL TO STORE, TRANSPORT, ORABANDON AN UNSECURED FIREARM IN A PLACEWHERE CHILDREN ARE LIKELY TO BE AND CANOBTAIN ACCESS TO THE FIREARM.”
Wisconsin:“IF YOU LEAVE A LOADED FIREARM WITHIN THEREACH OR EASY ACCESS OF A CHILD YOU MAY BEFINED OR IMPRISONED OR BOTH IF THE CHILDIMPROPERLY DISCHARGES, POSSESSES, OR EXHIBITSTHE FIREARM.”
* * * * * * * * * * * * * * * * * * * * * *
Please check with your licensed retailer or state police foradditional warnings which may be required by local law orregulation. Such regulations change constantly, and localauthorities are in the best position to advise you on such legalmatters.
5
This firearm was originally soldwith a key-operated lockingdevice. While it can help providesecure storage for your unloadedfirearm, any locking device canfail. All guns are designed to fireif they are loaded and the triggeris pulled. Therefore, never installthe locking device inside thetrigger guard or in any way thatit can possibly pull the trigger!Do not leave the keys in the lock.
The ultimate responsibility forsecure storage of any firearmmust depend upon its owner andhis or her individualcircumstances. Guns should besecurely stored unloaded, in asecure location, separate fromtheir ammunition.
See “Storage Warning”, page 23.
NEVER INSTALLLOCKING DEVICE
INSIDE TRIGGER GUARD
WHY ARE WE INCLUDING A FIRED CARTRIDGE CASEWITH EVERY RUGER PISTOL AND REVOLVER?
Certain states and jurisdictions now require that all newly manufactured pistolsand revolvers must be accompanied by a cartridge case, which has been test firedfrom that gun at the factory. The case must be placed in a sealed containerbearing certain information concerning this test cartridge.
At the time of retail sale in those jurisdictions, firearms dealers must forwardsuch test cartridge to a designated destination such as their State PoliceLaboratory. As independent Ruger Distributors have nationwide markets withoutterritorial restrictions, we have decided to include a fired cartridge case with allnew Ruger pistols and revolvers, to minimize the possibility of inadvertent non-compliance with these laws.
Retail customers located in other states, where laws or regulations do not requirethe dealer to so act, may be assured that the fired cartridge case they receive withthe firearm at the time of retail purchase is proof that your new Ruger firearmhas undergone our normal test firing procedures during manufacture.
6
WARNING – LOCKING DEVICES
DO NOT INSTALLINSIDE TRIGGER GUARD
INSTALL LOCKAS SHOWN HERE
FIREARMS SAFETY-YOUR RESPONSIBILITYSAFETY MUST BE THE FIRST AND CONSTANTCONSIDERATION OF EVERY PERSON WHOHANDLES FIREARMS AND AMMUNITION.
This Instruction Manual is designed to assist you in learning how to use and carefor your RUGER® SP101® revolver properly. Please contact us if you haveany questions about it.
Only when you are certain you fully understand the Manual and can properlycarry out its instructions should you practice loading, unloading, etc. with liveammunition. If you have any doubts about your ability to handle or use aparticular type of gun safely, then you should seek supervised instruction. Suchpersonalized instruction is often available from gun dealers, gun clubs or policedepartments. If none of these sources can help you, write to the National RifleAssociation, 11250 Waples Mill Road, Fairfax, VA 22030-7400. They will put youin touch with a source of personalized instruction.
The person possessing a gun has a full-time job. You cannot guess; you cannotforget. You must know how to use your firearm safely. Do not use any firearmwithout having a complete understanding of its particular characteristics andsafe use. Remember: There is no such thing as a foolproof gun.
TABLE OF CONTENTSPage
State-By-State Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3General Information and Mechanical Characteristics . . . . . . . . . . . . . . . . . . . . . 8Ammunition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Operation of “Double-Action Only” Revolvers . . . . . . . . . . . . . . . . . . . . . . . . . 12Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13To Load and Fire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14To Uncock (Decock) The Revolver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16To Unload or Eject Cartridge Cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Special Instructions for 9 mm Clips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22Care of Stainless Steel Revolvers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Sights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Sight Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Service and Parts Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Parts Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33The Basic Rules of Safe Firearms Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Ruger®, “SP101”®,and the Sturm, Ruger logo are registered U.S. trademarks.
7
8
FIREARMS ARE DANGEROUS WEAPONS–READ THE INSTRUCTIONS AND WARNINGS IN THIS
MANUAL THOROUGHLY AND CAREFULLY BEFORE USING.
GENERAL INFORMATIONAND MECHANICAL CHARACTERISTICS
The RUGER® SP101® revolver is a double-action firearm which embodiesmany features found in the famous RUGER® GP100® and RUGER®
SUPER REDHAWK® revolvers. The unique frame extension permits the useof full wrap-around style grips of any desired configuration. This feature reducesoverall weight and contributes to a desirable muzzle of heaviness. The crane andcylinder assembly of the SP101 revolver lock directly into the frame, both at therear of the cylinder and at the front of the crane. The ejector serves only as anejector – it does not rotate with the cylinder. All of this mechanism is readily
WARNING–ALTERATIONS
This product was designed tofunction properly in its originalcondition. Alterations can make itunsafe. Do not alter any part or addor substitute parts or accessoriesnot made by Sturm, Ruger & Co. Inc.
DO NOT ALTER ANY GUN
WARNINGS OF GREAT IMPORTANCE AREFOUND ON THE FOLLOWING PAGES:
Locking Devices 6 Cylinder Interlock 14Alterations 8 Firing 16Lead Exposure 10 Disassembly 19Ammunition 11 Lubrication 22Double-Action Only 12 Storage 23Handling 13 Parts Purchasers 26
OTHER CAUTIONS AND WARNINGS APPEARTHROUGHOUT THE MANUAL.
removable without tools and dismantles, along with the cylinder/crane group,into a small number of subassemblies for inspection and cleaning (See Figure 1).
The internal parts are installed either through the top or bottom of the grip-frame; therefore, no side plate is needed. The resulting double solid framecontributes greatly to the extraordinary strength and reliability of theserevolvers.
The RUGER® SP101® revolver has a transfer bar which is connected directlyto the trigger. The transfer-bar safety system provides that the hammer blow canbe transmitted to the firing pin only when the trigger is pulled all the way to therear. This is a positive internal safety feature.
NOMENCLATURE
9
FRONT SIGHT
MUZZLE
EJECTOR ROD
CYLINDER
TRIGGER GUARD PISTOL GRIPINSERT
GRIP SCREW
CRANE LATCH
HAMMER PIVOTASSEMBLY
HAMMERBARREL
TRIGGER
FRAME
FRONT SIGHT
HAMMER STRUT, MAINSPRING,& MAINSPRING SEAT
HAMMER ASSEMBLY
GRIP SCREW
HAMMER PIVOT ASSEMBLY
PISTOL GRIP
GRIP PANELLOCATOR
TRIGGER GUARDASSEMBLY
CYLINDER/CRANEASSEMBLY DISASSEMBLY PIN
Figure 1.
Figure 2.
Despite their many highly desirable features, Ruger revolvers–as with allfirearms–must at all times be handled with strict attention to correct safetypractices, and be inspected frequently to assure the gun is working properly.
10
Discharging firearms in poorly ventilatedareas, cleaning firearms, or handlingammunition may result in exposure tolead and other substances known to thestate of California to cause birth defects,reproductive harm, and other seriousphysical injury. Have adequate ventilationat all times. Wash hands thoroughly afterexposure.
SHOOTING OR CLEANING GUNSMAY EXPOSE YOU TO LEAD
WARNING – LEAD EXPOSURE
AMMUNITION
RUGER® SP101® revolvers are designed for use with cartridges of thecorrect caliber which are manufactured in accordance with the U.S. IndustryStandards. Be certain to use proper cartridges of the correct caliber. See page 21(“Care and Cleaning”) for important information on chamber cleaning.
Please refer to the Notes below regarding proper ammunition for the availableSP101 calibers.
Notes on Caliber .38 Special: .38 Special caliber revolvers are designedspecifically for modern higher-powered factory loaded cartridges, including .38Special and .38 Special + P ammunition.
Notes on .357 Magnum caliber: This revolver is designed to fire factory loaded.357 Magnum, .38 Special and .38 Special + P ammunition.
Special Ammunition Notice for .357 Revolvers marked “125 GR. BULLET”only: Some revolvers have slightly shorter cylinders and frames and aretherefore limited to the use of .357 Magnum ammunition with a maximumbullet weight of 125 grains and an overall loaded cartridge length of notmore than 1.57 inches. These revolvers are roll-marked with “125GR.BULLET” on the right side of the barrel.
Ammunition containing heavier bullets or of a longer length may not permitthe cylinder to close or rotate! You may not even be able to fire the revolver ifyou try to use longer or heavier bullets. Be sure the ammunition you wish touse in the revolver will chamber freely, and will permit the cylinder to open,close and rotate readily. Do not assume any ammunition will work withoutchecking it first.
All other .357 SP101 revolvers can use all standard factory .357 loads.
11
Notes on 9mm Parabellum Revolvers: This model is chambered for the 9mmParabellum (Luger) cartridge. A package of 9mm clips are supplied with therevolver and are required to allow proper ejection of the 9mm rimless cases. SeeSPECIAL INSTRUCTIONS FOR 9mm CLIPS, p. 14. Do not use any other 9mmcartridges (9mm Short, 9mm Bergmann, etc.).
Because 9mm cartridges are manufactured worldwide for use in pistols,revolvers, and submachine guns, it is possible to encounter cartridges which,when fired, develop pierced primers. If this occurs, discontinue the use of theparticular brand or type of ammunition. The possibility of a pierced primer isanother complete reason why a shooter should always wear protective glasses toshield his eyes. Use only metal jacketed bullets in 9mm revolvers. When a leadbullet is fired, its base expands and a ring of lead is shaved off and deposited inthe shoulder area of the chamber. A build-up of lead rings can prevent properchambering of cartridges because 9mm cartridge mouths seat on the chambershoulders.
Notes on .22 Caliber Long Rifle: The .22 cal. model is a six-shot double actionrevolver chambered for the .22 Long Rifle cartridge. The .22 Short, .22 Long and.22 shot cartridges can also be fired from this model. It should be noted thatextensive use of the .22 Short cartridge can cause a “ring” to be cut in eachcylinder chamber which may interfere with the extraction of Long and Long RifleCartridges.
Notes on Caliber .32 H & R Magnum: This six-shot SP101 chambered for theCaliber .32 H & R Magnum cartridge will also chamber the .32 S & W cartridgeand the .32 S & W Long cartridge. The use of other than .32 H & R Magnumcartridges, may, in some loadings, result in unsatisfactory accuracy.
For reasons noted above, revolver chambers should be cleaned regularly andchamber cleaning should be the first corrective action when cartridges of thecorrect caliber and type do not chamber properly.
WARNING –AMMUNITIONDeath, serious injury, and damagecan result from the use of wrongammunition, bore obstructions,powder overloads, or incorrectcartridge components. Always wearshooting glasses and hearingprotectors.
IMPROPER AMMUNITIONDESTROYS GUNS
12
AMMUNITION (CARTRIDGES) NOTICEWE SPECIFICALLY DISCLAIM RESPONSIBILITY FOR
ANY DAMAGE OR INJURY WHATSOEVER OCCURRING INCONNECTION WITH, OR AS THE RESULT OF, THE USE IN
THE SP101 REVOLVER OF FAULTY, OR NON-STANDARD, OR“RE-MANUFACTURED”, OR HAND LOADED (RELOADED)
AMMUNITION, OR OF CARTRIDGES OTHER THAN THOSEFOR WHICH THE FIREARM WAS ORIGINALLY CHAMBERED.
OPERATION OF“DOUBLE-ACTION ONLY “ REVOLVERS
(This section applied only to “Double-Action Only” revolvers, identified by theirlack of a hammer spur)
The model you have selected is equipped with a special trigger mechanism thatpermits only “double-action” firing. The hammer cannot be manually cocked,since there is no full cock notch or hammer spur. The revolver can only be firedby a relatively long (“double-action”) pull of the trigger which draws the hammerrearward and then releases it to fire every shot.
It is important to note that the mechanism of the gun will not permit anothershot to be fired unless the trigger is first fully released and then pulled again.
The revolver has an internal transfer bar that will not allow the hammer tocontact the firing pin and fire the gun until the operator completely pulls thetrigger.
WARNING–DOUBLE-ACTION ONLY
Do not attempt to manually cockthe hammer! Since there is no full-cock notch, the hammer will fallforward when released, and if fingerpressure is applied to the trigger,the revolver can fire. The automaticsafeties that prevent firing if thehammer falls are deactivated if thetrigger is pulled. Do not touch thetrigger unless you intend to shootthe revolver!
DO NOT COCK HAMMER
13
CAUTION: When firing the double-action only revolver,be sure that the trigger is released completely to its fully
forward position before attempting to pull the trigger for asubsequent shot. If the trigger finger is allowed to interfere with thefull recovery of the trigger (preventing it from moving through aboutthe last one-eighth inch of its forward movement), pulling the triggerwill not fire the revolver. The trigger must be fully released after eachshot is fired. This characteristic is found on all modern double-actionrevolvers and “double-action only” pistols.
HANDLING
CARRYING: The SP101 revolver can be carried with all chambers loaded. Whenthe hammer and trigger are fully forward, the transfer-bar is lowered out of itsfiring position and the hammer rests directly on the frame.
WARNING –HANDLING
DRY-FIRING“Dry Firing” is practicing the trigger pull of the empty revolver for practice andfamiliarity. The SP101 revolver can be dry-fired without damage to the firing pinor internal components.
Be sure that the revolver is unloaded before handling. Be sure of your bulletstop, even when dry-firing for practice. Do not dry-fire the revolver with theplastic ‘safety disc’ on the cylinder.
If the trigger is held to the rear, the guncan fire if the hammer strikes thetransfer bar. Note that it need not be adeliberate effort to pull the trigger. Anysituation where the trigger attains itsrearward position and permits thetransfer bar to be interposed between thehammer and the firing pin can cause thecartridge under the firing pin todischarge.
NEVER DROP OR STRIKE THEREVOLVER – COCKED OR UNCOCKEDCARRY AND HANDLE THE REVOLVERIN SUCH A MANNER THAT THEHAMMER AND TRIGGER WILL NOT BESTRUCK.
NEVER CARRY ANYREVOLVER WITH THE
HAMMER COCKED OR THETRIGGER HELD TO THE REAR
WARNING –CYLINDER INTERLOCK
14
2. Insert cartridges and gently close cylinder, making sure it is securely latched.Do not “flip” the cylinder open or shut.
3. The revolver is now ready to fire, either “double-action” by pulling the triggerthrough its complete arc for each shot, or “single-action” by cocking thehammer and then pulling the trigger for each shot. The trigger pull issomewhat shorter and lighter when the revolver is fired single action, andthis is the preferred mode for precise shots or target shooting.
FIGURE 3LOADING THE REVOLVER.➧
When correctly operated, the cylindercannot be opened when the hammer iscocked, and the hammer/triggermechanism is not able to be operateduntil the cylinder is locked shut.However, this safety interlock can beintentionally defeated if the crane latch isdepressed and the hammer is thencocked while the cylinder is opened. Ifthe cylinder is then shut when thehammer is cocked, the hammer may falland the gun may fire.
NEVER CLOSE OR OPENTHE CYLINDER WHILE
THE HAMMER IS COCKED
TO LOAD AND FIREBe sure the revolver is pointed in a safe direction and is
never cocked while loading.
1. Press the crane latch and guide cylinder out of frame to the left to its loadingposition (See Figure 3, below).
4. DO NOT TOUCH THE TRIGGER UNTIL YOU ARE READY TO FIRE.
5. DO NOT HOLD THE REVOLVER BY THE BARREL OR CYLINDER WHENFIRING.
CAUTION–DOUBLE ACTION FIRING
15
When firing in the double actionmode, be sure that the trigger isreleased completely to its fullyforward position before pulling thetrigger for a subsequent shot. Ifthe trigger finger is allowed tointerfere with the full recovery ofthe trigger (preventing it frommoving thru about the last one-eighth inch of its forwardmovement), the trigger cannot bepulled again for another discharge.The trigger must be fully releasedafter each shot is fired. Thischaracteristic is found in allmodern double-action revolversand “double-action only” pistols.
FULLY RELEASETRIGGER
BETWEEN SHOTS
When firing the SP101 revolver, be sureall persons are a safe distance to the rearof the shooter. When fired, all revolversdischarge hot gas and particles of lead,powder grains, or lubricant through theclearance gap between the cylinder andthe rear of the barrel at high speed. Thiscan injure a person who is standing tooclose to the revolver.
When firing the SP101 revolver (or anyrevolver), always be certain that nothing– including your hands – is in the path ofthe hot gas and particles which aredischarged from the front and sides of thecylinder.
When shooting, adequate eye protectionis essential. Shooters and bystandersmust wear shooting glasses. Hearingprotection must also be worn. Exposureto shooting noise can damage hearing.
HOT GASES EXITBARREL/CYLINDER GAP
TO UNCOCK (DECOCK) THE REVOLVERIf your revolver is cocked, and you wish to let the hammer down to its forwardposition (against the frame), proceed as follows: USE EXTREME CARE WHENATTEMPTING TO DECOCK THE REVOLVER, AS THE THUMB SLIPPINGDURING THIS PROCESS CAN RESULT IN AN ACCIDENTAL DISCHARGE IFTHE TRIGGER IS HELD TO THE REAR.
1. Make certain that the revolver is pointed in a safe direction (See Rule 2, Page35).
2. Make certain both hands are dry and not impeded in any way – gloves,bandages, cold, etc.
3. Grasp the revolver (if right handed) so that the thumb and forefinger of yourleft hand are firmly holding the frame, forward of the trigger guard. Thus,your left hand is in full control of the revolver (See Figure 4A, Page 17).
4. Place your right thumb firmly on the hammer spur and, with your thumbsecurely in control of the hammer, squeeze the trigger only enough to permitthe hammer to ‘break free’ of the trigger. At that instant, IMMEDIATELYRELEASE THE TRIGGER and then slowly permit the hammer, STILLSECURE UNDER YOUR THUMB, to move fully forward to its resting positionagainst the frame. NOTE: It is imperative that finger pressure be removedfrom the trigger just as soon as it is free of the hammer. Then, properly, thetrigger and hammer will move towards their fully forward rest positionstogether (See Figure 4B, Page 17).
16
WARNING–FIRING
Practice this important gun handling skill with an unloaded revolver until youhave developed the proper control and ‘touch’ to decock your revolver safely. Thekey to safe decocking is having the weight of the revolver controlled with onehand, while the thumb and forefinger of the ‘shooting hand’ control thehammer and trigger. Improperly restraining the trigger during this proceduremay result in the hammer not resting fully against the frame. If this shouldoccur, carefully repeat the procedure for decocking, steps 1–4 again.
UNCOCKING THE REVOLVER
FIGURE 4
A. With the thumb controlling the hammeras shown (1), squeeze trigger to permithammer to ‘break free’ (2).
TO UNLOAD OR EJECT CARTRIDGE CASES
KEEP THE REVOLVER POINTED IN A SAFE DIRECTION!DO NOT ATTEMPT TO UNLOAD WHEN THE HAMMER IS COCKED.
1. Uncock the revolver (See pp. 16 - 17)
2. Press crane latch. Guide cylinder out left of frame as for loading. The revolvernow cannot be fired.
3. Push head of ejector rod smartly toward rear of cylinder until it stops. Thisaction will extract cartridges or fired cases. Do not eject live cartridges ontoany surface where a primer might strike a solid object and discharge thecartridge.
4. Check to be sure all chambers are empty.
1
2
4
3
17
B. When hammer is free, IMMEDIATELYrelease trigger (3). Then lower hammerslowly to its resting position completelydown against frame (4).
NOTE: When ejecting fired cartridge cases, position the revolver at ahigh angle so the cases will come fully out of the chambers and not slipunder the ejector. This high angle positioning is not necessary whenejecting unfired cartridges.
18
SPECIAL INSTRUCTIONS FOR 9MM CLIPS9mm revolvers require special clips to extract cartridges using the ejector rodbecause this cartridge has no rim for the ejector to act against. Individualcartridges may be fired without the clip, but will then require that each cartridgeor fired case be individually removed to unload the revolver.
TO LOAD CLIP:
Hold clip on outside diameter in one hand. With thumb and forefinger ofopposite hand, press cartridge’s extractor groove into clip until it snaps intoplace. Continue until clip is fully loaded. Load cartridges, along with the clip,into the cylinder.
3
2
4
1
CORRECT UNLOADING SEQUENCE
DISASSEMBLYRead instructions before disassembling a gun.
1. BE CERTAIN THE REVOLVER IS UNLOADED BEFORE DISASSEMBLY.
2. Using a properly fitting screwdriver, removegrip screw. Remove pistol grip inserts fromgrips. Grip panel locator may then be removed.Pull grip downward off frame. Take care not tolose the disassembly pin, which may fall freewhen the grip is removed.
3. Cock the hammer. Insert disassembly pinabout one half its length into the hole at therear of the mainspring strut. Lacking a
disassembly pin, any similar instrument will serve (See Figure 5).
4. With thumb on hammer spur, squeeze trigger allowing hammer to go fullyforward. Lift out mainspring assembly. CAUTION: Do not remove thedisassembly pin until the mainspring assembly is reinstalled in the revolver atthe time of reassembly. Doing so will permitthe mainspring to fly off its strut with greatforce and may cause injury.
5. Pull trigger and remove hammer pivot whileholding trigger in a rearward position. Lifthammer out of the top of the frame whiletrigger is held in a rearward position (SeeFigure 6).
TO UNLOAD CLIP:
Eject clip and cases from cylinder. While holding clip on outside diameter, pressempty cases of clip for removal. Clip is now ready to be reloaded. Inspect clipsafter each use. If broken, bent or cracked, discard and replace. Additional clipscan be purchased from out Newport, New Hampshire Service Department.
19
WARNING –DISASSEMBLYAlways unload a firearm beforecleaning, lubrication, disassemblyor assembly.Never remove or install a loadedcylinder – it can fire if dropped orstruck.
UNLOAD BEFORE CLEANING
3
2
4
1
Figure 5
Figure 6
NOTE: If you cannot supply sufficient force to the plunger using the mainspringassembly as a “tool”, then use a screwdriver of appropriate size and insertthrough hole in frame. It may be necessary to slightly depress the trigger whileremoving the trigger guard assembly.
7. Cradle the revolver frame in your left hand and with the thumb of your righthand press cylinder latch button, swing out cylinder assembly and remove itforward from the frame.
8. Further disassembly is not essential for normal cleaning purposes. Any furtherdisassembly should only be undertaken by factory service personnel.
REASSEMBLYAGAIN, BE CERTAIN REVOLVER IS UNLOADED!
Before starting reassembly, be certain that all components and the inside of theframe are thoroughly clean. In particular the tongue on the front of the triggerguard and its mating recess in the frame must be completely clean.
1. Replace cylinder and crane assembly in frame and close cylinder.
2. Hook front of trigger guard into recess inframe (See Figure 7). Align pawl in its recessin the frame and be sure transfer bar is incorrect position in frame then allow latch tore-engage. If solid resistance is felt whenswinging trigger guard into frame, or iftrigger guard will not lock into position re-check position of pawl and transfer bar (SeeFigure 9).
TRANSFERBAR
PAWL
6. Use mainspring assembly to depress trigger guard lock plunger located insideframe at rear of trigger guard. Simultaneously pull down and remove triggerguard assembly (See Figure 7 & 8).
20
Figure 7 Figure 8
Figure 9
NOTE: At this point in reassembly trigger should function to rotate and lock thecylinder. Pull the trigger a few times, to check proper functioning, as always withthe revolver pointed in a safe direction.
3. Hold trigger in its rearward position and insert hammer into frame. Installhammer pivot. Release trigger and permit hammer to go fully forward.
4. With hammer forward, insert mainspring assembly into frame. Position thetwo ends of notch in the mainspring seat onto the matching projections of thegrip frame. (Note: The large notch in the mainspring seat should be forward toallow clearance for the grip screw.) Hold mainspring assembly in position andcock hammer. It may be necessary to move the mainspring assembly a little toproperly position the upper end of the mainspring strut to rest in recess in thehammer. When the hammer is cocked, disassembly pin can be removed (It willfall free).
5. Squeeze trigger and ease hammer down. Put the disassembly pin in its “nest.”Push grip upward onto the frame, install grip panel locator and place pistolinserts into position. Install and tighten grip panel screw.
6. Open and close cylinder. Function the trigger and hammer single action anddouble action to be certain that all parts are working properly.
CARE AND CLEANINGALWAYS BE CERTAIN THE REVOLVER IS UNLOADED BEFORE CLEANING.
The internal mechanism of the SP101 revolver can be lubricated withoutdisassembly. A few drops of light oil recommended as suitable for firearms,applied periodically about the various frame openings, will work its way into themechanism parts. The exterior of the revolver and the bore and chambers shouldbe thoroughly cleaned and then wiped with an oily cloth if the gun is to bestored. Do not apply excess lubrication.
To clean the revolver after firing, swing the cylinder out and clean the barrelfrom the muzzle by running a cleaning rod with a solvent coated patch throughthe bore several times. A bronze wire brush (of correct size for gun caliber)attached to the cleaning rod should then be pushed the full length of the boreseveral times. Again swab the bore with a solvent coated patch. Then wipe therod clean and, using a dry patch, swab the bore until it is clean. Examine thebore to be sure that no fouling remains. Repeat the above procedure for each ofthe five chambers.
Chambers must be thoroughly scrubbed to remove build-up of bullet metal andfiring residue. A dirty chamber can prevent full seating of a cartridge, which inturn causes the cylinder to bind. DO NOT APPLY EXCESSIVE OIL TOUNDERSIDE OF EJECTOR – AREA SHOULD BE WIPED DRY WITH OILYCLOTH. Also, the underside of the ejector (‘star’) and the area of the cylinderwhere the ejector seats, must be clean. Dirt can prevent the ejector from fullyseating. That condition can cause hard closing of the cylinder and interfere withproper cylinder rotation.
21
STORAGEGUNS SHOULD NOT BE STORED LOADED!
Do not keep your revolver in a leather, fabric or canvas holster when it is stored.These materials attract moisture, even though the holster may appear to beperfectly dry.
TO RENDER THE REVOLVER INOPERATIVE FOR SAFE STORAGE
With the muzzle pointed in a safe direction, press the cylinder latch and swing thecylinder outward. Check to be sure that each chamber is completely unloaded!With a coin or screwdriver, unscrew the grip panels and remove the grips. Cock thehammer and then insert the disassembly pin into the hole at the bottom of themainspring strut. Uncock the hammer, remove the hammer strut from the frame,remove the hammer pivot from the frame, and lift the hammer out of the top ofthe frame. Use a screwdriver to depress the trigger housing latch and remove thetrigger assembly from the bottom of the frame.
Store the hammer and the trigger assembly in different locations from the frame.When disassembled in this manner, the revolver is inoperable. It is impossible tofire the revolver until the trigger assembly and the hammer have been correctlyreassembled into the frame.
USE THE LOCKING DEVICE SUPPLIED WITHTHE REVOLVER FOR STORAGE.
(SEE PAGE 6)
22
WARNING –LUBRICATIONFiring a revolver with oil, grease, or anyother material even partially obstructing thebore may result in damage to the revolverand injury to the shooter and those nearby.
Do not spray or apply lubricants directly onammunition. If the powder charge of acartridge is affected by the lubricant, it maynot be ignited, but the energy from theprimer may be sufficient to push the bulletinto the bore where it may become lodged.Firing a subsequent bullet onto theobstructed bore may damage the revolverand cause injury to the shooter and thosenearby. Use lubricants properly. You areresponsible for the proper care andmaintenance of your firearms.
IMPROPER LUBRICATIONDESTROYS GUNS
If lead bullet loads are fired extensively, lead build-up may cause cylinderbinding. Lubricate the cylinder crane gap with Break-Free® CLP or some otherlubrication which meets mil. spec. Mil-163460 to prevent this condition.
Never place or store any firearm insuch a manner that it may bedislodged. Firearms should always bestored securely and unloaded, awayfrom children and careless adults. Usethe locking device originally suppliedwith this firearm for storage.
The use of a locking device or safetylock is only one aspect of responsiblefirearms storage. For increased safety,firearms should be stored unloaded andlocked in a location that is bothseparate from their ammunition andinaccessible to children and any otherunauthorized person.
STORE SECURELY & UNLOADED
23
WARNING –STORAGE
To reassemble the revolver for firing, carefully reinsert the trigger housing intothe frame. Place the hammer into the top of the frame, and reinsert the hammerpivot pin. Cock the hammer, reinstall the mainspring strut, and remove thedisassembly pin from the mainspring strut. Lower the hammer and replace thegrips on the revolver. The revolver is now reassembled and can be loaded andfired normally.
While the revolver is less likely to be used by unauthorized persons whendisassembled in the above manner, it is always safest to store a firearm withthe supplied locking device correctly installed, or to store the firearm in a gunsafe or other secure location, away from children and unauthorized adults.Guns should always be stored securely, unloaded and separate from theirammunition.
CARE OF STAINLESS STEEL REVOLVERSRevolvers made of stainless steel are more resistant to corrosion than blued steelrevolvers. However, in the interest of proper operation and long life of yourrevolver, inspect it frequently and clean, lubricate and apply an appropriate rustpreventative.
Sometimes surface discoloration may be noted, particularly in the grip area ofstainless steel revolvers, resulting from perspiration. Contact with some types ofholsters can also cause stains or rusting. Rusting may also occur as a result ofthe revolver being exposed to moisture, humidity, salt air or chemicals.
SIGHTS.38 SPL, .357 Mag. & 9mm
The SP101 .38 SPL, .357 Mag. & 9mm revolvers are provided with fixed sights.To change the front sight, drive out the pin in the barrel rib with a small punchand lift out sight blade.
24
Rear sight Suggested sight picture
Top of front sight even with topof rear sight. Front sight centeredin notch of rear sight. Targetbullseye centered on top of frontsight.
Minor discoloration can usually be removed by rubbing the stained area with anabrasive ink eraser, crocus cloth, or a “metal polishing” compound. When usingany of these abrasives, proceed with care and use light pressure to achieve ablending of ‘color’ with those areas that are not discolored.
External surfaces of the barrel, frame and cylinder should be cleaned and wipeddry after use or after exposure to adverse conditions. If the revolver is to bestored, coat it with a light film of oil or preservative. Where the revolver is incontinuing use, and the presence of oil or grease would be objectionable, thenthe external surface can be coated (after cleaning and drying) with a paste waxformulated for use on metals. Apply the wax sparingly, allow time for it to dryhard, then buff lightly with a soft cloth. When applying the wax, take care that itdoes not get into the mechanism or on the functioning parts such as thehammer, trigger, crane latch, etc. A properly applied hard wax coating will notinterfere with gun handling and it will provide a measure of protection.
25
SIGHT ADJUSTMENTS.22 LR & .32 H & R Magnum
The SP101 .22 LR & .32 H & R Magnum revolvers are equipped with sightsadjustable for windage. Each click of the rear sight adjustment screw will movethe point of bullet impact approximately 1/2” on the target at 25 yards using a 4”barrel length.
To move the point of impact to the right: Turn the click screw counterclockwise.
To move the point of impact to the left: Turn the click screw clockwise.
SERVICE AND PARTS POLICYIf you have any questions with regard to the performance of your RUGER®
SP101 revolver please write or call (603-865-2442) our Product ServiceDepartment in Newport, New Hampshire 03773, fully describing allcircumstances and conditions involved. If you should return your revolver to thefactory for repair, or order parts for it, please comply with the followingsuggestions for prompt service:
SHIPPING FIREARMS FOR REPAIRRUGER® SP101 revolvers returned to the factory for repair should be sentto: Sturm, Ruger & Company, Inc., Product Service Department, 411 SunapeeSt., Newport, New Hampshire 03773. Telephone (603) 865-2442.
Guns should be sent prepaid. We will not accept collect shipments.
The Federal Gun Control Act, as well as the laws of most States and localities, donot prohibit an individual (who is not otherwise barred from purchasing orpossessing a firearm) from shipping a firearm directly to the manufacturer forrepair. However, before you ship your revolver to us, be certain that your State orlocality does not have a law or regulation which will prohibit you from receivingthe revolver from us after it has been repaired. If such receiving is prohibited,then please have a Federally Licensed firearms dealer ship the gun to us. If yourrevolver is sent to us by a dealer, it will be returned to him after being repaired.If a handgun (pistol or revolver) is shipped by an individual who does not hold aFederal Firearms License, it must be shipped via U.P.S. (Next Day Air) Personswho do not hold a Federal Firearms License are prohibited by Federal law fromshipping a handgun by Mail. Handguns mailed in violation of the law areimpounded by the Post Office.
WARNING–BEFORE SHIPPING ANYFIREARM, BE ABSOLUTELY CERTAIN THAT ITAND ITS CYLINDER ARE UNLOADED. DONOT SHIP CARTRIDGES WITH A FIREARM.
DO NOT SEND GUN BOXES OR LITERATURE THAT YOU CONSIDER TO BECOLLECTOR’S ITEMS – THESE ARE INVARIABLY DAMAGED ORDESTROYED IN SHIPMENT. Please do not include holster, grip panels, or otheraccessories with a firearm being shipped to the factory for service. Always insureyour shipment.
Enclose a letter which includes your name, address, telephone number, serialnumber and model of the firearm. Describe in detail the trouble you haveexperienced with your firearm, or the work you wish to have done. Merely statingthat the firearm “needs repair” is inadequate information.
Work performed will bear a net minimum labor charge of $20.00 plus a $20.00shipping and handling charge. The charge for metal refinishing the RUGER®
SP101 revolver is $50.00 plus a $20.00 shipping and handling charge. Customgunsmithing service or nonstandard alterations are NOT AVAILABLE from RugerProduct Service Departments.
26
ORDERING PARTSPlease contact the New Hampshire Product Service Department for partsavailability and current prices. All parts orders for the RUGER® SP101revolvers should be sent to: Sturm, Ruger & Co., Inc., Product ServiceDepartment, 411 Sunapee Street, Newport, New Hampshire 03773, 603-865-2442. We cannot comply with open account or C.O.D. orders. Payment in theform of a check, money order, Visa or Mastercard must accompany your order.Credit Card orders must include the account number, expiration date andwhether it is a Visa or Mastercard account. Minimum parts order is $1.00 plus$3.50 shipping and handling charge. Order parts by Part Name and Part Numberand include the entire serial number of the firearm for which the parts are beingordered. There is a minimum net labor charge of $20.00 plus $20.00 shippingand handling charge if the parts are factory fitted. All factory fitted parts are fiton an exchange basis only. We will not return the replaced parts.
WARNING–PARTS PURCHASERSIt is the purchaser’s responsibility to beabsolutely certain that any parts ordered from thefactory are correctly fitted and installed. Firearmsare complicated mechanisms and IMPROPERFITTING OF PARTS MAY RESULT IN ADANGEROUS MALFUNCTION, DAMAGE TOTHE FIREARM, AND SERIOUS INJURY TO THESHOOTER AND OTHER PERSONS. Thepurchaser and installer of parts must accept fullresponsibility for the correct adjustment andfunctioning of the revolver after such installation.
PARTS MUST FIT CORRECTLY
27
Barrels, cylinders, cylinder/crane assemblies and a number of other componentparts must be fitted at the factory. Company policy is to proof-test and/orfunction fire all barrels after fitting to the frames in which they are to be used.This procedure ensures maximum protection to our customers. The specialproof-test ammunition used in this testing is sold only to bonafide firearmsmanufacturers and is not available to gun shops, gunsmiths, or individuals.
Because the frame of the RUGER® SP101 revolver is a serial numberedcomponent, it is defined as a “firearm” by Federal law and is not sold as aseparate component.
*Parts designated by an asterisk must be factory fitted. These parts are fitted onan exchange basis only. We will not return the replaced parts. We will not returnany part that is broken, malfunctioning, badly worn or has been modified. See“Warning – Parts Purchasers”, p. 26.
CAUTION: A gun containing modified, broken,malfunctioning, or badly worn parts should not be fired.
28
RU
GE
R®
SP
10
1®
RE
VO
LV
ER
PAR
TS L
IST
Des
ign,
pri
ces
and
spec
ifica
tion
s su
bjec
t to
cha
nge
wit
hout
not
ice.
SPE
CIF
Y M
OD
EL
AND
CAL
IBE
R W
HE
N O
RD
ER
ING
(See
Exp
lode
d Vi
ew o
n Pa
ge 3
3)
Par
t N
ame
Par
t N
o.M
odel
*B
arre
l, 2
1/4”
KW
0062
5SP
101
-.3
57 c
al.
*B
arre
l, 3
1/16
”K
W00
626
SP10
1-
.357
cal
.*
Bar
rel,
2 1/
4”K
W00
601
SP10
1-
.38
Spec
ial
*B
arre
l, 2
1/4”
, Ext
ende
d Fr
ame
KW
0064
0SP
101
-.3
8 Sp
ecia
l*
Bar
rel,
3 1/
16”
KW
0060
2SP
101
-.3
8 Sp
ecia
l*
Bar
rel,
2 1/
4”K
W00
617
SP10
1-
9mm
*B
arre
l, 3
1/16
”K
W00
616
SP10
1-
9mm
*B
arre
l, 2
1/4”
KW
0060
7SP
101
-.2
2 ca
l.*
Bar
rel,
4”, H
alf S
hrou
dK
W00
620
SP10
1-
.22
cal.
*B
arre
l, 4”
, Ful
l Shr
oud
KW
0060
6SP
101
-.2
2 ca
l.*
Bar
rel,
3 1/
16”
KW
0061
2SP
101
-.3
2 H
&R
*B
arre
l, 4”
, Ful
l Shr
oud
KW
0061
1SP
101
-.3
2 H
&R
Cab
le L
ock,
10”
, Not
Illu
stra
ted
PM12
0AAl
l SP1
01 M
odel
sC
ase
Onl
y, S
mal
lR
GC
-SAl
l SP1
01 M
odel
sC
ente
r Pi
n Lo
ckK
W05
300
All S
P101
Mod
els
Cen
ter
Pin
Rod
KW
0540
0SP
101
-.3
8 Sp
ecia
l, 9m
m, .
22 c
al.,
.32
H&
R.
Cen
ter
Pin
Rod
KW
0541
0SP
101
-.3
57 c
al.
Cen
ter
Pin
Spri
ngK
W03
400
SP10
1-
.38
Spec
ial,
9mm
, .22
cal
., .3
2 H
&R
Cen
ter
Pin
Spri
ngK
W03
410
SP10
1-
.357
cal
.C
lip, F
ull M
oon,
10
per
pack
age
W06
400-
10SP
101
-9m
m*
Cra
ne &
Cra
ne P
ivot
Ass
embl
yK
W00
800A
SP10
1-
.38
Spec
ial,
9mm
, .22
cal
., .3
2 H
&R
29
Par
t N
ame
Par
t N
o.M
odel
*C
rane
& C
rane
Piv
ot A
ssem
bly
KW
0081
2ASP
101
-.3
57 c
al.
*C
rane
Lat
chK
W00
900
All S
P101
Mod
els
*C
rane
Lat
ch P
ivot
KW
0270
0Al
l SP1
01 M
odel
sC
rane
Lat
ch S
prin
gK
E-5
7Al
l SP1
01 M
odel
sC
rane
Lat
ch S
prin
g Pl
unge
rK
H05
100
All S
P101
Mod
els
*C
rane
Piv
ot L
ock
Plun
ger
KH
0670
0Al
l SP1
01 M
odel
s*
Cra
ne P
ivot
Loc
k Sp
ring
KH
0760
0Al
l SP1
01 M
odel
s*
Cyl
inde
rK
W00
100
SP10
1-
.357
cal
. or
.38
Spec
ial
*C
ylin
der
KW
0011
6SP
101
-.3
57 c
al.
*C
ylin
der
KW
0010
4SP
101
-9m
m*
Cyl
inde
r, 6-
shot
KW
0010
2SP
101
-.2
2 ca
l.*
Cyl
inde
r, 6-
shot
KW
0010
3SP
101
-.3
2 H
&R
Cyl
inde
r La
tch
KW
0450
1Al
l SP1
01 M
odel
sC
ylin
der
Latc
h Pi
vot
KH
0140
0Al
l SP1
01 M
odel
sC
ylin
der
Latc
h Pl
unge
rK
E-5
1Al
l SP1
01 M
odel
sC
ylin
der
Latc
h Sp
ring
KH
0500
0Al
l SP1
01 M
odel
sD
isas
sem
bly
Pin
E-6
3Al
l SP1
01 M
odel
s*
Eje
ctor
KW
0181
7SP
101
-.3
57 c
al.
*E
ject
orK
W01
800
SP10
1-
.38
Spec
ial
*E
ject
orK
W01
805
SP10
1-
9mm
*E
ject
orK
W01
802
SP10
1-
.22
cal.
*E
ject
orK
W01
803
SP10
1-
.32
H&
RE
ject
or A
lignm
ent
Pin,
(2
Req
’d.)
KE
-35
All S
P101
Mod
els
*E
ject
or R
etai
ner
KW
0240
0Al
l SP1
01 M
odel
sE
ject
or R
odK
W02
300
All S
P101
Mod
els
Eje
ctor
Spr
ing
KW
0250
0SP
101
-.3
8 Sp
ecia
l, 9m
m, .
22 c
al.,
.32
H&
RE
ject
or S
prin
gK
W02
510
SP10
1-
.357
cal
.
30
Par
t N
ame
Par
t N
o.M
odel
Ferr
ule
(Rig
ht S
ide)
, Not
Illu
stra
ted
W01
014
All S
P101
Mod
els
Ferr
ule
(Lef
t Si
de)
W01
015
All S
P101
Mod
els
*Fi
ring
Pin
KH
0210
0SP
101
-.3
57 c
al.,
.38
Spec
ial,
9mm
, .32
H&
R*
Firi
ng P
inK
XR
0210
0SP
101
-.2
2 ca
l.Fi
ring
Pin
Reb
ound
Spr
ing
KE
-48
All S
P101
Mod
els
Fron
t La
tch
KW
0310
0Al
l SP1
01 M
odel
sFr
ont
Latc
h Pi
vot
Lock
KH
0750
0Al
l SP1
01 M
odel
sFr
ont
Latc
h Pi
vot
Lock
Spr
ing
KH
0770
0Al
l SP1
01 M
odel
sFr
ont
Latc
h Pi
vot
Pin
KW
0560
0Al
l SP1
01 M
odel
sFr
ont
Latc
h Sp
ring
KE
-57
All S
P101
Mod
els
Fron
t La
tch
Spri
ng P
lung
erK
W06
800
All S
P101
Mod
els
Fron
t Si
ght
W03
602
SP10
1-
.357
cal
., .3
8 Sp
ecia
l, 9m
mFr
ont
Sigh
tW
0360
3SP
101
-.2
2 ca
l.Fr
ont
Sigh
tW
0360
4SP
101
-.3
2 H
&R
Fron
t Si
ght
Cro
ss P
inK
W02
600
All S
P101
Mod
els
Gri
p, 1
Pie
ce R
ubbe
r, N
o In
sert
sW
0100
0Al
l SP1
01 M
odel
sG
rip
wit
h Pl
asti
c In
sert
sW
2100
0Al
l SP1
01 M
odel
s(D
isas
sem
bly
Pin
& S
crew
Inc
lude
d)G
rip
Inse
rts,
Bla
ck P
last
ic (
Sold
in P
airs
Onl
y)W
2101
8Al
l SP1
01 M
odel
sG
rip
Inse
rts,
Woo
d (
Sold
in P
airs
Onl
y)W
IAl
l SP1
01 M
odel
sG
rip
Pane
l Loc
ator
W03
300
All S
P101
Mod
els
Gri
p Pa
nel S
crew
KW
0130
0Al
l SP1
01 M
odel
s*
Ham
mer
Ass
embl
yK
W24
000
All S
P101
Mod
els
*H
amm
er A
ssem
bly,
Spu
rles
s, N
ot I
llust
rate
dK
W24
004
All S
P101
Mod
els
*H
amm
er D
ogK
W01
900
All S
P101
Mod
els
Ham
mer
Dog
Piv
ot P
inK
E-2
2Al
l SP1
01 M
odel
s
31
Par
t N
ame
Par
t N
o.M
odel
Ham
mer
Dog
Spr
ing
KE
-57
All S
P101
Mod
els
Ham
mer
Dog
Spr
ing
Plun
ger
KH
0510
0Al
l SP1
01 M
odel
sH
amm
er P
ivot
Ass
embl
yK
E-1
6Al
l SP1
01 M
odel
sH
amm
er S
trut
KT0
1500
All S
P101
Mod
els
Ham
mer
Str
ut M
ains
prin
gK
W00
401
All S
P101
Mod
els
Ham
mer
Str
ut M
ains
prin
g Se
atK
T005
00Al
l SP1
01 M
odel
sPa
wl
KW
0070
0SP
101
-.3
57 c
al.,
.38
Spec
ial,
9mm
Paw
lK
W00
701
SP10
1-
.22
cal.,
.32
H&
RPa
wl P
lung
erK
H05
100
All S
P101
Mod
els
Paw
l Plu
nger
Spr
ing
KH
0500
0Al
l SP1
01 M
odel
sR
ear
Sigh
t Ad
just
men
t Sc
rew
W05
900
SP10
1-
.22
cal.,
.32
H&
RR
ear
Sigh
t B
lade
W05
902
SP10
1-
.22
cal.,
.32
H&
RR
ear
Sigh
t Sp
ring
MR
0590
7SP
101
-.2
2 ca
l., .3
2 H
&R
*R
ecoi
l Pla
teK
MR
0200
0SP
101
-.3
57 c
al.,
.38
Spec
ial,
9mm
, .32
H&
R*
Rec
oil P
late
KX
R02
000
SP10
1-
.22
cal.
Rec
oil P
late
Cro
ss P
inK
E-4
9SP
101
-.3
57 c
al.,
.38
Spec
ial,
9mm
, .32
H&
RR
ecoi
l Pla
te C
ross
Pin
KH
0490
0SP
101
-.2
2 ca
l.Sa
fety
Ins
ert
W10
000
SP10
1-
.357
cal
., .3
8 Sp
ecia
l, 9m
m, .
32 H
&R
Safe
ty I
nser
tW
1000
2SP
101
-.2
2 ca
l.Tr
ansf
er B
arK
W01
700
SP10
1-
.357
cal
., .3
8 Sp
ecia
l, 9m
m, .
32 H
&R
Tran
sfer
Bar
KW
0170
1SP
101
-.2
2 ca
l.*
Trig
ger
Asse
mbl
yK
W23
900
All S
P101
Mod
els
*Tr
igge
r G
uard
KW
0030
0Al
l SP1
01 M
odel
sTr
igge
r G
uard
Lat
chK
W04
600
All S
P101
Mod
els
Trig
ger
Gua
rd L
atch
Pin
KE
-22
All S
P101
Mod
els
Trig
ger
Gua
rd L
atch
Spr
ing
KW
0380
0Al
l SP1
01 M
odel
sTr
igge
r Li
nkK
W07
100
All S
P101
Mod
els
32
Par
t N
ame
Par
t N
o.M
odel
Trig
ger
Link
Pin
KH
0640
0Al
l SP1
01 M
odel
sTr
igge
r Li
nk P
lung
erK
W03
700
All S
P101
Mod
els
Trig
ger
Pivo
t Pi
nK
E02
800
All S
P101
Mod
els
Trig
ger
Plun
ger
KH
0320
0Al
l SP1
01 M
odel
s
*PA
RTS
SO
MAR
KE
D M
UST
BE
FAC
TOR
Y FI
TTE
D
34
SP
101
RE
VO
LVE
R M
EC
HA
NIS
M
KW
0540
0 C
EN
TE
R P
IN R
OD
KW
0530
0 C
EN
TE
R P
IN L
OC
K
KW
0170
0 T
RA
NS
FE
R B
AR
KH
0210
0 F
IRIN
G P
IN
KW
0400
0 H
AM
ME
R
KW
0090
0 C
RA
NE
LA
TC
H
KW
0070
0 P
AW
L
KT
0150
0H
AM
ME
R S
TR
UT
KW
0040
1 M
AIN
SP
RIN
G
KT
0050
0 M
AIN
SP
RIN
G S
EA
T
KW
0230
0 E
JEC
TO
R R
OD
KW
0310
0 F
RO
NT
LA
TC
H
KE
-57
& K
W06
800
FR
ON
T L
AT
CH
SP
RIN
G &
PLU
NG
ER
KW
0450
1 C
YLI
ND
ER
LA
TC
H
KW
0390
0 T
RIG
GE
R
KW
0710
0 T
RIG
GE
R L
INK
KW
0370
0 T
RIG
GE
R L
INK
PLU
NG
ER
KW
0380
0 T
RIG
GE
R G
UA
RD
LA
TC
H S
PR
ING
KW
0460
0 T
RIG
GE
R G
UA
RD
LA
TC
H
THE BASIC RULES OF SAFE FIREARMS HANDLINGWe believe that Americans have a right to purchase and use firearms for lawfulpurposes. The private ownership of firearms in America is traditional, but thatownership imposes the responsibility on the gun owner to use his firearms ina way which will ensure his own safety and that of others. When firearms areused in a safe and responsible manner, they are a great source of pleasure andsatisfaction, and represent a fundamental part of our personal liberty.
Firearms do not cause accidents! Firearms accidents are almost always foundto have been the result of carelessness, or ignorance on the part of the shooterof the basic rules of safe gun handling.
The following rules must be observed by gun users at all times. Safe gunhandling is not just desirable, it is absolutely essential to your safety, the safetyof others, and the continuation of gun ownership and sport shooting as weknow it today.
1. LEARN THE MECHANICAL AND HANDLINGCHARACTERISTICS OF THE FIREARM YOU ARE USING.
Not all firearms are the same. Themethod of carrying and handlingfirearms varies in accordance with themechanical provisions for avoidingaccidental discharge and the variousproper procedures for loading andunloading. No person should handleany firearm without first havingthoroughly familiarized himself withthe particular type of firearm he isusing, and with safe gun handling ingeneral.
2. ALWAYS KEEP THEMUZZLE POINTED IN ASAFE DIRECTION.Be sure of the bullet stop behind yourtarget, even when dry-firing. Never letthe muzzle of a firearm point at anypart of your body or at anotherperson. This is particularly importantwhen loading or unloading a firearm.In the event of an accidentaldischarge, no injury can occur as longas the muzzle is pointing in a safedirection. A safe direction means adirection which will not permit a
discharged bullet to strike a person, or to strike an object from which thebullet may ricochet.
35
RUGER®
INSTRUCTION MANUAL
READ THE INSTRUCTIONS
AND WARNINGS IN THIS
MANUAL CAREFULLY BEFORE
USING THIS FIREARM.
A safe direction must take into account the fact that a bullet may penetrate awall, ceiling, floor, window, etc., and strike a person or damage property. Makeit a habit to know exactly where the muzzle of your gun is pointing wheneveryou handle it, and be sure that you are always in control of the direction inwhich the muzzle is pointing, even if you fall or stumble. Keep your finger offthe trigger until you are ready to shoot.
3. FIREARMS SHOULD BE UNLOADED WHEN NOT INUSE.
Firearms should be loaded only whenyou are in the field or on the targetrange or shooting area, ready to shoot.Firearms and ammunition should besecurely locked in safes, racks orcabinets, or by using the lockingdevice supplied with the firearm whennot in use. Ammunition should safelybe stored separate from firearms.Store your firearms out of sight ofvisitors and children. It is the gunowner’s responsibility to be certainthat children and persons unfamiliarwith firearms cannot gain access tofirearms, ammunition, orcomponents.
4. BE SURE THE BARREL ISCLEAR OF OBSTRUCTIONSBEFORE SHOOTING.
Even a bit of mud, snow or excesslubricating oil or grease in the boremay cause the barrel to bulge, oreven burst on firing, and can causeserious injury to the shooter andbystanders. Be sure that you areusing ammunition of the propercaliber and loading for the gun youare using. If the report or recoil onfiring seems weak, or doesn’t seemquite right, CEASE FIRING IMMEDIATELY, unload your firearm, and check tobe sure that no obstruction has become lodged in the barrel.
36
3
2
4
1
5. BE SURE OF YOURTARGET BEFORE YOUSHOOT.Don’t shoot unless you knowexactly where your bullet is goingto strike. Be sure of the bulletstop behind your target, evenwhen dry-firing with an unloadedgun. If you are in the fieldhunting, do not fire at amovement or noise. Take the timeto be absolutely certain of yourtarget before you pull the trigger.
6. WEAR SHOOTINGGLASSES AND HEARINGPROTECTORS WHENYOU SHOOT.All shooters should wearprotective shooting glasses andadequate hearing protectors whenshooting. Exposure to shootingnoise can damage hearing, andadequate eye protection whenshooting is essential.
7. NEVER CLIMB A TREEOR FENCE WITH ALOADED FIREARM.Put the firearm down carefullybefore climbing a fence, andunload it before climbing ordescending a tree or jumpingover a ditch or other obstruction.Never pull or push a loadedfirearm toward yourself oranother person. When in doubt,or whenever you are about to doanything awkward, unload yourgun!
37
8. DON’T SHOOT AT AHARD SURFACE, OR ATWATER.Bullets can glance off manysurfaces like rocks or the surfaceof water and travel inunpredictable directions withconsiderable velocity.
9. NEVER TRANSPORT ALOADED FIREARM.Firearms should always beunloaded before being placed in avehicle. A suitable carrying caseor scabbard should by used tocarry an unloaded firearm to andfrom the shooting area.
10. AVOID ALCOHOLICBEVERAGES WHENSHOOTING.Don’t drink until the day’sshooting is over. Handlingfirearms while under theinfluence of alcohol in any form,or medications that could affectyour judgment or co-ordination,constitutes a criminal disregardfor the safety of others.
38
A BRIEF ACCOUNT OF AN EXTRAORDINARYACHIEVEMENT: RUGER FIREARMS
One of the few American firearms manufacturers whose managementhas remained in the same family since starting in business, Sturm,Ruger & Company, Inc., had its beginning in a small machine shopoccupying a rented frame building in Southport, Connecticut. InJanuary, 1949, with an initial investment of only $50,000 and an idea,William B. Ruger and Alexander M. Sturm started production of a .22caliber autoloading pistol–a design which was so successful that itbecame the cornerstone upon which one of the most comprehensivelines of sporting firearms ever made in America was established. AfterAlex Sturm’s death in 1951, William B. Ruger continued to direct thecompany alone and today, William B. Ruger, Jr. continues to provideguidance which has made this company a sound and successfulenterprise.
Sturm, Ruger & Company, in this relatively short time, has establisheditself as a leading small arms design organization, developing a uniqueand broad line of fine quality sporting, military and police firearms tobecome one of the world’s most famous producers of revolvers, pistols,rifles and shotguns. Since 1949 Ruger craftsmen have built manymillions of firearms.
During its five decades of growth and progress under the leadership ofWilliam B. Ruger, the company developed a business philosophy andimplemented policies which represent a constructive influence in the lifeof modern America. From the beginning, Sturm, Ruger & Companyplayed a positive role in conservation efforts and has supported theinterests of shooters through such groups as the National RifleAssociation, National Shooting Sports Foundation, and many regionalsportsmen’s organizations.
The company has always endeavored to market its firearms forconstructive and recreational purposes, to emphasize the traditionalaspects of shooting, to render meaningful public services and toencourage shooters in constructive, responsible, and safe participation inthe shooting sports. Its motto is “Arms Makers For ResponsibleCitizens.”
Today, Sturm, Ruger & Company is particularly mindful of thoseelements which have contributed to the creation of its success, andextends heartfelt thanks to its many loyal employees and customers.
A current catalog of Ruger firearms is available free upon request toSturm, Ruger & Co., Inc., Southport, CT 06890
39
WHY NO WARRANTY CARD HAS BEENPACKED WITH THIS NEW RUGER FIREARM
The Magnuson-Moss Act (Public Law 93-637) does not require anyseller or manufacturer of a consumer product to give a writtenwarranty. It does provide that if a written warranty is given, it must bedesignated as “limited” or as “full” and sets minimum standards for a“full” warranty. Sturm, Ruger & Company, Inc. has elected not toprovide any written warranty, either “limited” or “full”, rather than toattempt to comply with the provisions of the Magnuson-Moss Act andthe regulations issued thereunder. There are certain impliedwarranties under state law with respect to sales of consumer goods. Asthe extent and interpretation of these implied warranties varies fromstate to state, you should refer to your state statutes. Sturm, Ruger &Company wishes to assure its customers of its continued interest inproviding service to owners of Ruger firearms.
STURM, RUGER & Company, Inc.Southport, Connecticut 06890 U.S.A.
http://www.ruger.com
“Arms Makers For Responsible Citizens” ®
A COPY OF THE INSTRUCTION MANUAL FOR ANY RUGERFIREARM IS AVAILABLE FROM THE FACTORY FREE ON REQUEST.
THESE INSTRUCTION MANUALS CONTAIN IMPORTANTWARNINGS WHICH MUST BE UNDERSTOOD
BEFORE USING THESE FIREARMS.
“RUGER”, the Sturm, Ruger logo, “SINGLE-SIX”, “BLACKHAWK”, “REDHAWK”, “SECURITY-SIX”,“SPEED-SIX”, “SERVICE-SIX”, “BEARCAT”, “OLD ARMY”, “10/22”, “MINI-14”, “MINI THIRTY”,“RANCH RIFLE”, “M77”, “77/22”, “77/44”, “77/50”, “GP-100”, “SP101”, “P-85” and “VAQUERO”
are registered U.S. trademarks.“77/17” & “Gold Label” are Ruger trademarks.