3

Put the camera support in place and secure it with the 2 MCFAS00197 screws in the front.

4 Secure the back of the camera support with the 2 MCFAS00221 screws.

1 Slide the nose of the Bebop 2 back on.*

Caution: make sure you do not damage the GPS during the process.

SPARE PARTS / Bebop 2 / Central body

To replace the central body under the Bebop 2, you need a T5 screwdriver, a T6 screwdriver, pliers and a box cutter.

It is recommended to use the Parrot Toolbox for this operation.

REFERENCES: Red Central Body: PF070226AB / White Central Body: PF070203AB

2 Slide the nose forward to remove it.*

Caution: make sure you do not damage the GPS during the process.

1 Put the cross back on the drone.

4 With a box cutter, peel off the sticker.

x6

1 Remove the 2 screws holding the nose.

2 Secure the nose with the 2 screws.

2 Disconnect the GPS from the flex.

1 Connect the GPS to the flex.

2 Remove the camera support and all its elements.

2

Put the lock on top of the connector. Make sure the screw holes are aligned.

G207

G207

1REMOVING

THE NOSE

14INSTALLING

THE NOSE

2REMOVING

THE GPS

13INSTALLING

THE GPS

3REMOVING

THE CAMERA

12INSTALLING

THE CAMERA

1 Remove the 2 MCFAS00197 and the 2 MCFAS00221 screws.

1 Fix the connector of the camera support on the motherboard.

1 Remove the 3 screws holding the GPS to the support of the camera.

2 Secure the GPS with 3 new MCFAS00220 screws.

1 Remove the 4 screws holding the foot and remove the old foot.

1 Connect the cables to each connector.

3 Remove cable from the antenna.

3 Fix the antenna back to the cable.

2 Slide the antenna off the foot.

2 Secure each connector with 2 MCFAS00333 screws.

5 Disconnect the antennas of the front feet.

5 Put each foot back into place and secure them with 4 screws.

4

10

REMOVING

THE FRONT FEET

INSTALLING

THE FRONT FEET

5

11

REMOVING

THE REAR FEET

INSTALLING

THE REAR FEET

REMOVING THE

CAMERA AND THE FAN

UNDER THE DRONE

1 Use a T5 screwdriver to remove the 4 screws holding the foot.

1 Connect the cables to each connector.

1 Use the pliers to remove the metal stems of the old motherboard.

5 Disconnect the cables of the fan and remove it completely.

4 Slightly pull on the cable to disconnect them from each connector.

4 Slide the antenna in the foot.

2 Remove the foot and use a T6 screwdriver to remove the 2 screws holding the connector.

2 Secure each connector with 2 MCFAS00333 screws.

2 Use a T5 screwdriver to remove the 3 screws holding the fan.

6 Disconnect the connector of the camera and remove it completely.

3 Slightly pull on the cable to disconnect it from the connector.

3 Put each foot back into place and secure them with 4 screws.

3 Use a T5 screwdriver to remove the 2 screws holding the camera.

2 Connect the fan to the motherboard.

5 Secure the fan with the 3 MCFAS00197 screws .

6 Use the pliers to screw the metal stems on the new motherboard.

3 With a box cutter, peel off the sticker. Put the sticker back into place.

1 Use a T5 screwdriver to remove the 2 screws holding the camera.

4 Secure the camera with the 2 MCFAS00199 screws.

AA

CC

AA C C

1 Use the pliers to unscrew the 4 washers under the drone.

3 Secure the cross with the washers. 2 Make sure to correctly put back all the cables.

2 Remove the cross.

REMOVING

THE CROSS

INSTALLING

THE CROSS

6

9

7

Package content:1 central body / 6 screws

INSTALLING THE

ELEMENTS ON THE

NEW CENTRAL BODY8

* Using a new nose part will ease the process and prevent from damaging the GPS.

D I F F I C U L T Y L E V E L