spc58xxmb evaluation board - stmicroelectronics · 2021. 8. 5. · 4.9 regulator power jumpers....

IntroductionThis document describes the STMicroelectronics SPC58XXMB evaluation board.

Figure 1. SPC58XXMB

SPC58XXMB evaluation board

UM2740

User manual

UM2740 - Rev 1 - January 2021For further information contact your local STMicroelectronics sales office.

www.st.com

1 Overview

This user’s manual details the setup and configuration of the STMicroelectronics SPC58XXMB evaluationboard (hereafter referred to as the EVB). The EVB is intended to provide a mechanism for easy customerevaluation of the SPC58xx family and SPC57xx family of microcontrollers, and to facilitate hardware and softwaredevelopment.At the time of writing this document, the SPC58xx family will consist of the 40 nm powertrain and safety devicesand SPC57xx family will consist of the 55 nm powertrain and safety devices.The EVB is intended for bench / laboratory use and has been designed using normal temperature specifiedcomponents (+70°C).

1.1 Package contentsAn SPC58XXMB evaluation board package includes the following items:• SPC58XXMB evaluation board• Power supply 12 VDC – 2 A• EULA

UM2740Overview

UM2740 - Rev 1 page 2/45

2 License agreement

The packaging of this evaluation board was sealed with a seal stating, " by breaking this seal, you agree to theterms and conditions of the evaluation board license agreement, the terms and conditions of which are availableat https://www.st.com/resource/en/evaluation_board_terms_of_use/evaluationproductlicenseagreement.pdf ".Upon breaking the seal, you and STMicroelectronics entered into the evaluation board license agreement, acopy of which is also enclosed with the evaluation board for convenience.

Attention: This evaluation board only offers limited features for evaluating ST products. It has not been tested for usewith other products and is not suitable for any safety or other commercial or consumer application. Thisevaluation board is otherwise provided “AS IS” and STMicroelectronics disclaims all warranties, express orimplied, including the implied warranties of merchantability and fitness for a particular purpose.

UM2740License agreement

UM2740 - Rev 1 page 3/45

3 Handling precautions

Please take care to handle the package contents in a manner such as to prevent electrostatic discharge.Before the EVB is used or power is applied, please fully read the following sections on how to correctly configurethe board. Failure to correctly configure the board may cause irreparable component, MCU or EVB damage.

UM2740Handling precautions

UM2740 - Rev 1 page 4/45

4 Hardware description

4.1 List of acronymsThe table below provides a list and description of acronyms used throughout this document.

Table 1. List of acronyms

Acronym Description

1.25V_SR Supply voltage from the 1.25 V switching regulator

3.3V_SR Supply voltage from the 3.3 V switching regulator

5V_LR Supply voltage from the 5.0 V linear regulator

5V_SR Supply voltage from the 5.0 V switching regulator

ADC Analog-to-Digital converter

ESR0 External signal reset

EVB Evaluation board

FEC Fast ethernet controller module

GND Ground

HV High voltage (3.3 V and/or 5 V)

LED Light emitting diode

LV Low voltage (1.25 V)

MCU Microcontroller

OSC Oscillator

P12V 12 V EVB supply power domain

PORST Power-on reset

PWR Power

RX Receive

SIPI Serial Interprocessor Interface

TBD To be defined

TX Transmit

VSS Ground

UM2740Hardware description

UM2740 - Rev 1 page 5/45

4.2 Modular conceptFor maximum flexibility and simplicity, the EVB has been designed as a modular development platform. The EVBmain board does not contain an MCU. Instead, the MCU is fitted to an MCU daughter card (occasionally referredto as an adapter board). This approach means that the same EVB platform can be used for multiple packagesand MCU derivatives within the SPC58xx family and the SPC57xx family. High density connectors provide theinterface between the EVB and MCU daughter cards as shown in the figure below. See Section 4.3 Daughtercard availability for more details on the daughter cards and Section 4.17 Board interface connectors for moredetails on the interface connectors.

Figure 2. Modular concept - motherboard and MCU daughter card

For details on your specific daughter card, please consult the instructions included with the daughter card.The EVB is designed to use the motherboard and the daughter in conjunction. However, it is possible to use thedaughter cards standalone.

UM2740Modular concept

UM2740 - Rev 1 page 6/45

4.3 Daughter card availability

Table 2. Daughter card

Daughter card number Device

SPC58NHADPT176S SPC58NHxxE7

SPC58NHADPT302S SPC58NHxxC3

SPC58NHADPT386S SPC58NHxxC5

SPC58XCADPT176SSPC584BxxE7

SPC58xCxxE7

SPC58XCADPT292S SPC584CxxC5

SPC58XXADPT64S

SPC582BxxE1

SPC584BxxE1

SPC58xCxxE1

SPC58XXADPT100S

SPC582BxxE3

SPC584BxxE3

SPC58xCxxE3

SPC58xGxxE3

SPC58XXADPT144S

SPC582BxxE5

SPC584BxxE5

SPC58xCxxE5

SPC58xGxxE5

SPC58XXADPT176S

SPC58xGxxE3

SPC58xExxE3

SPC58xNxxE3

SPC58XXADPT292SSPC58xGxxC5

SPC58xExxC5

SPC582BADPT48S SPC582BxxQ3

SPC584BADPT176SSPC584BxxE7

SPC58xCxxE7

SPC570SADPT64S SPC570SxxE1

SPC570SADPT100SSPC570SxxE3

SPC574SxxE3

SPC572LADPT80S SPC572LxxF2

SPC572LADPT100S SPC572LxxE3

SPC574KADPT144S SPC574KxxE5



SPC574SADPT244S SPC574SxxC2

SPC56HKADPT257S SPC56HKxxC3

UM2740Daughter card availability

UM2740 - Rev 1 page 7/45

4.4 EVB featuresThe EVB system consists of a motherboard and a daughter card, both with distinct features.The mother board provides the following key features:• Support provided for different SPC58xx MCUs and SPC57xx MCUs by utilizing MCU daughter cards• Single 12 V external power supply input with four on-board regulators providing all the necessary EVB and

MCU voltages; power supplied to the EVB via a 2.1 mm barrel style power jack or a 2-way level connector• Master power switch and regulator status LEDs• Two 240-way high-density daughter card expansion connectors allowing connection of the MCU daughter

card or a custom board for additional application specific circuitry• All MCU signals readily accessible at a port-ordered group of 0.1” pitch headers• RS232/SCI physical interface and standard DB9 female connector• FlexRAY interface• LINFlexD interface• CAN FD interfaces (data rates up to 5 Mbit/s), one configurable to be connected to one out of two CAN

modules, and one connected to a dedicated third CAN module• 10/100 Mbps ethernet interface• Variable resistor, driving between 5 V and ground• user switches and 4 user LEDs, freely connectable• Liberal scattering of GND test points (surface mount loops) placed throughout the EVB

The daughter cards provide the following features:• MCU (soldered or through a socket)• Flexible MCU clocking options allow provision of an external clock via SMA connector or 40 MHz EVB

clock oscillator circuit. Jumpers on the daughter card allow selection between these external clocks. SMAconnector on MCU-CLKOUT signal for easy access.

• User reset switch with reset status LEDs• Standard 14-pin JTAG debug connector and 34-pin Samtec Nexus3+ connector• 10-pin Serial Interprocessor Interface (SIPI) connector• Liberal scattering of ground and test points (surface mount loops) placed throughout the EVB

Note: To avoid confusion between jumpers and headers, all EVB jumpers are implemented as 2 mm pitch whereasheaders are 0.1 inch (2.54 mm). This prevents inadvertently fitting a jumper to a header.

4.5 CautionBefore the EVB is used or power is applied, please fully read the following sections on how to correctly configurethe board. Failure to correctly configure the board may cause irreparable component, MCU or EVB damage.

UM2740EVB features

UM2740 - Rev 1 page 8/45

4.6 ConfigurationThis section details the configuration of each of the EVB functional blocks.The EVB has been designed keeping in mind the ease of use, and has been segmented into functional blocksas shown in the figure below. A detailed silkscreen legend has been used throughout the board to identify allswitches, jumpers and user connectors.

Figure 3. EVB functional blocks

UM2740Configuration

UM2740 - Rev 1 page 9/45

4.7 Power supply configurationThe EVB requires an external power supply voltage of 12 V DC, minimum 1 A. This allows the EVB to be easilyused in a vehicle if required. The single input voltage is regulated on-board using three switching regulators toprovide the necessary EVB and MCU operating voltages of 5.0 V, 3.3 V and 1.25 V, and one 5 V linear regulatorfor the ADC supplies and references.For flexibility there are two different power supply input connectors on the motherboard as detailed below. Thereis also a power supply option on the daughter card to use the daughter card in standalone mode. Please refer todaughter card documents for details on power input.

4.8 Motherboard power supply connectors2.1 mm barrel connector – P28:

Figure 4. Power supply barrel connector

2-way lever connector – P32:

Figure 5. 2-lever power connector

This can be used to connect a bare wire lead to the EVB, typically from a laboratory power supply. Thepolarization of the connectors is clearly marked on the EVB. A special care must be taken to ensure correctconnection.

UM2740Power supply configuration

UM2740 - Rev 1 page 10/45

4.9 Regulator power jumpersThere are four power regulator circuits on the SPC58xx motherboard that supply the required voltages to operatethe MCUs:• 1.25V_SR: 1.25 V switching regulator to supply the core voltage• 5V_SR: 5 V switching regulator to supply the power management controller, I/O and peripherals• 3.3V_SR: 3.3 V switching regulator for Ethernet, FlexRAY, debug and I/O• 5V_LR: 5 V linear regulator for ADC supply and reference

All regulators have the option of being disabled/enabled if they are not required. By default (jumpers are off),all switching regulators are enabled and the 5 V linear regulator is disabled. The regulators can be enabledindividually by the following jumper settings:• Connecting J57 enables the 5.0 V linear regulator• Disconnecting J58 enables the 5.0 V switching regulator• Disconnecting J59 enables the 3.3 V switching regulator• Disconnecting J60 enables the 1.25 V switching regulator

The regulators supply power to the daughter cards through the board connector. The individual selection andconfiguration of the MCU supplies are done on the daughter cards.Not all the supported daughter card MCUs require all the supplies to be switched on. Please refer to the individualdaughter card user guide for details.

4.10 Power switch, status LEDs and useThe main power switch (slide switch SW5) can be used to isolate the power supply input from the EVB voltageregulators if required.• Moving the slide switch to the right (away from connector P33) will turn the EVB on• Moving the slide switch to the left (towards connector P33) will turn the EVB off

When power is applied to the EVB, four green power LEDs adjacent to the voltage regulators show the presenceof the supply voltages as follows:• LED D9 – Indicates that the 5.0 V linear regulator is enabled and working correctly• LED D11 – Indicates that the 5.0 V switching regulator is enabled and working correctly• LED D12 – Indicates that the 3.3 V switching regulator is enabled and working correctly• LED D13 – Indicates that the 1.25 V switching regulator is enabled and working correctly

If no LED is illuminated when power is applied to the EVB and the regulators are correctly enabled using theappropriate jumpers, it is possible that either power switch SW5 is in the “OFF” position or that the fuse F1 hasblown. The fuse will blow if power is applied to the EVB in reverse-bias, where a protection diode ensures that themain fuse blows rather than causing damage to the EVB circuitry. If the fuse has blown, check the bias of yourpower supply connection then replace fuse F1 with a 20 mm 1.5 A fast blow fuse.

UM2740Regulator power jumpers

UM2740 - Rev 1 page 11/45

4.11 CAN configurationThe EVB has two high speed CAN FD transceivers and two female standard DB9 connectors to provide physicalCAN FD interfaces for the MCU.The pinout of the DB9 female connector (J5) is shown in the below figure.

Figure 6. CAN DB9 connector pinout

For flexibility, the CAN FD transceiver I/Os are also connected to two standard 0.1” connectors (P4 and P5) at thetop side of the PCB. The figure below shows the pin-out for these connectors.

Figure 7. CAN 3pin header interface connector

By default, the CAN interfaces are not enabled. To enable the CAN interfaces the jumpers detailed in the tablebelow need to be placed.

UM2740CAN configuration

UM2740 - Rev 1 page 12/45

Table 3. CAN control jumpers

Jumper Label Description

J23 CAN2_EN

PHY U2 configuration

1-2: WAKE to GND

3-4: STB to 5 V

5-6: EN to 5 V

J32 CAN21-2: PHY TX to MCU

3-4: PHY RX to MCU

J33 CAN-PWR1-2: 5.0V_SR to PHY U2 VCC

3-4: 12 V to PHY U2 VBAT

J34 INH/ERR

PHY U2 signal out

1: ERR

2: INH

J21 CAN_EN

PHY U1 configuration

1-2: WAKE to GND

3-4: STB to 5 V

5-6: EN to 5 V

J35 CAN-PWR1-2: 5.0V_SR to PHY U1 VCC


J37 TTCAN_TX/MCAN1_TX

PHY U1 TX to MCU

1-2: TTCAN TX

2-3: MCAN1 TX

J38 TTCAN/MCAN1

PHY U1 RX to MCU

1-2: TTCAN RX

2-3: MCAN1 RX

J36 INH/ERR

PHY U1 signal out

1: ERR

2: INH

4.12 RS232 configurationA female DB9 connector J19 and a RS232 transceiver device provide a physical RS232 interface, allowing adirect RS232 connection to a PC or terminal.The figure below shows the pin-out of the RS232 connector. It is to note that the hardware flow control is notsupported on this implementation.

Figure 8. RS232 physical interface connector

UM2740RS232 configuration

UM2740 - Rev 1 page 13/45

By default the RS232 interface is not enabled. The user needs to place the jumpers detailed in Table 4. RS232control jumpers to enable the RS232 interface.

Table 4. RS232 control jumpers


J13 SCI TX TX enable

J14 SCI RX RX enable

J25 SCI_PWR Transceiver power on

4.13 LIN configurationThe EVB is fitted with a LIN transceiver (U50) and two different style connectors:• a standard LIN Molex connector (J14) at the edge of the board• a standard 0.1" connector (P3).

The figure below shows the pin-out of the Molex connector J4.

Figure 9. LIN molex connector

For flexibility, the LIN transceiver is also connected to a standard 0.1” connector (P3) at the top side of the PCBas shown in Figure 10. LIN 4pin header interface connector. For ease of use, the 12 V EVB supply is fed to pin1of P3 and the LIN transceiver power input to pin2. This allows the LIN transceiver to be powered directly from theEVB supply by simply linking pins 1 and 2 of connector P3 using a 0.1" jumper shunt.

Figure 10. LIN 4pin header interface connector

By default, the LIN interface is not enabled. To enable the LIN interface the jumpers detailed in the table belowneed to be placed.

UM2740LIN configuration

UM2740 - Rev 1 page 14/45

Table 5. LIN control jumpers


J15 LIN_EN LIN PHY (U50) enable

J16 LIN_RX LIN RX enable

J17 LIN_TX LIN TX enable

4.14 FlexRAY configurationThe EVB is fitted with two FlexRAY transceivers, a female DB9 connector (for both transceivers) and twoalternative connectors. Jumpers J27 and J30 are provided to route the respective MCU signals to the physicalinterfaces.The figure below shows the pin-out of the DB9 connector (J2).

Figure 11. FlexRAY DB9 connector pinout

For flexibility, the FlexRAY transceiver is also connected to two FlexRAY connectors (P1 & P2) and two 2pinMolex connectors (J1 & J3, not populated by default) at the top side of the EVB. the figure below shows theconnections for both types of connectors.

Figure 12. FlexRAY alternative connector pin-outs

By default, the FlexRAY interface is not enabled. To enable the FlexRAY interface the jumpers detailed in thebelow table FlexRAY control jumpers need to be placed.

UM2740FlexRAY configuration

UM2740 - Rev 1 page 15/45

Table 6. FlexRAY control jumpers


J29 FR_PWR

FlexRay transceiver VIO selection

1-2: 12 V to VBAT

3-4: 5V_SR to VCC and VBUF

5-6: 3.3V_SR to VIO

J27 FR_A

1-2: PHY U4 TX to MCU

3-4: PHY U4 TXEN to MCU

5-6: PHY U4 RX to MCU

J28 FR_A

PHY U4 configuration:

1-2: 3.3 V (VIO) to BGE

3-4: 3.3 V (VIO) to EN

5-6: 3.3 V (VIO) to STBY

7-8: GND to WAKE

J30 FR_B




J31 FR_B


1-2: 3.3 V (VIO) to BGE

3-4: 3.3 V (VIO) to EN


7-8: GND to WAKE

UM2740FlexRAY configuration

UM2740 - Rev 1 page 16/45

4.15 Ethernet configurationThe EVB is fitted with a standard RJ45 Ethernet connector (J7) and an Ethernet transceiver (U6).By default, the Ethernet interface is not enabled. To enable the Ethernet interface the jumpers detailed inTable 5. LIN control jumpers need to be placed.

Table 7. Ethernet control jumpers

Jumper Description

J22 PHY power on (jumper placed on default)

J18 RXCLK

J20 CRS_LEDCFG

J24 RXER_MDIXEN

J26 RXDV_MIIMODE

J39 RXD0_PHYAD1

J40 RXD1_PHYAD1

J41 RXD2_PHYAD2

J42 RXD3_PHYAD3

J44 COL_PHYAD0

J45 TXEN

J46 TXCLK

J47 TXD0

J48 TXD1

J49 TXD2

J50 TXD3_SNIMODE

J51 MDC

J52 MDIO

UM2740Ethernet configuration

UM2740 - Rev 1 page 17/45

4.16 Motherboard test pointsSeveral test points of different shapes and functionalities are scattered around the EVB to allow an easy accessto MCU and reference signals. This chapter summarizes and describes the available test points. Motherboard testpoints are listed and detailed in the below table.

Table 8. Test points - motherboard

Signal TP name Shape Description

GND GT1 Hook Ground reference











1.25V_SR JP1 Pin 1.25V_SR reference








5V_SR JP9 Pin 5V_SR reference




GND JP13 Pin Ground reference




5V_SR TP15 Hook 5V_SR reference

5V_LR TP14 Hook 5V_LR reference

3.3V_SR TP16 Hook 3.3V_SR reference

1.25V_SR TP17 Hook 1.25V_SR reference

FRA-INH2 TP5 Pad FlexRAY

FRA-INH1 TP1 Pad FlexRAY

FRA-ERRN TP2 Pad FlexRAY

FRA-RXEN TP6 Pad FlexRAY

UM2740Motherboard test points

UM2740 - Rev 1 page 18/45

Signal TP name Shape Description

FRB-INH2 TP7 Pad FlexRAY

FRB-INH1 TP3 Pad FlexRAY

FRB-ERRN TP4 Pad FlexRAY

FRB-RXEN TP8 Pad FlexRAY

FR_DBG0 TP10 Pad FlexRAY debug0




FEC 25MHz TP9 Pad Ethernet clock

UM2740Motherboard test points

UM2740 - Rev 1 page 19/45

4.17 Board interface connectorsThis chapter provides a useful cross reference to see the connection from the motherboard to the board interfaceconnector, and what MCU pins are connected to the interface connector on the daughter cards.The Table 7. Ethernet control jumpers lists all the connections to the board interface connector on bothmotherboard and daughter cards. The table on the left lists the 240 connections for the first interface connector(J43), the table on the right lists the 240 connections for the second interface connector (J56): the column‘Motherboard’ shows the motherboard connections to the interface connectors like power supply connections anduser area port pins.Ground signals are not listed here. A solid ground connection is achieved through the middle bar of the interfaceconnector.

Table 9. Board interface connector details

Connector Motherboard Connector Motherboard

A-1 1.25V_SR B-240 1.25V_SR

A-2 1.25V_SR B-239 1.25V_SR

A-3 1.25V_SR B-238 1.25V_SR

A-4 1.25V_SR B-237 1.25V_SR

A-5 PA0 B-236 PB0

A-6 PA1 B-235 PB1

A-7 PA2 B-234 PB2

A-8 PA3 B-233 PB3

A-9 PA4 B-232 PB4

A-10 PA5 B-231 PB5

A-11 PA6 B-230 PB6

A-12 PA7 B-229 PB7

A-13 PA8 B-228 PB8

A-14 PA9 B-227 PB9

A-15 PA10 B-226 PB10

A-16 PA11 B-225 PB11

A-17 PA12 B-224 PB12

A-18 PA13 B-223 PB13

A-19 PA14 B-222 PB14

A-20 PA15 B-221 PB15

A-21 5.0V_SR B-220 5.0V_SR

A-22 5.0V_SR B-219 5.0V_SR

A-23 5.0V_SR B-218 5.0V_SR

A-24 5.0V_SR B-217 5.0V_SR

A-25 PC0 B-216 PD0

A-26 PC1 B-215 PD1

A-27 PC2 B-214 PD2

A-28 PC3 B-213 PD3

A-29 PC4 B-212 PD4

A-30 PC5 B-211 PD5

A-31 PC6 B-210 PD6

UM2740Board interface connectors

UM2740 - Rev 1 page 20/45


A-32 PC7 B-209 PD7

A-33 PC8 B-208 PD8

A-34 PC9 B-207 PD9

A-35 PC10 B-206 PD10

A-36 PC11 B-205 PD11

A-37 PC12 B-204 PD12

A-38 PC13 B-203 PD13

A-39 PC14 B-202 PD14

A-40 PC15 B-201 PD15

A-41 3.3V_SR B-200 3.3V_SR

A-42 3.3V_SR B-199 3.3V_SR

A-43 3.3V_SR B-198 3.3V_SR

A-44 3.3V_SR B-197 3.3V_SR

A-45 PE0 B-196 PF0

A-46 PE1 B-195 PF1

A-47 PE2 B-194 PF2

A-48 PE3 B-193 PF3

A-49 PE4 B-192 PF4

A-50 PE5 B-191 PF5

A-51 PE6 B-190 PF6

A-52 PE7 B-189 PF7

A-53 PE8 B-188 PF8

A-54 PE9 B-187 PF9

A-55 PE10 B-186 PF10

A-56 PE11 B-185 PF11

A-57 PE12 B-184 PF12

A-58 PE13 B-183 PF13

A-59 PE14 B-182 PF14

A-60 PE15 B-181 PF15

A-61 1.25V_SR B-180 1.25V_SR

A-62 1.25V_SR B-179 1.25V_SR

A-63 1.25V_SR B-178 1.25V_SR

A-64 1.25V_SR B-177 1.25V_SR

A-65 PG0 B-176 PH0

A-66 PG1 B-175 PH1

A-67 PG2 B-174 PH2

A-68 PG3 B-173 PH3

A-69 PG4 B-172 PH4

A-70 PG5 B-171 PH5

A-71 PG6 B-170 PH6

A-72 PG7 B-169 PH7


UM2740 - Rev 1 page 21/45


A-73 PG8 B-168 PH8

A-74 PG9 B-167 PH9

A-75 PG10 B-166 PH10

A-76 PG11 B-165 PH11

A-77 PG12 B-164 PH12

A-78 PG13 B-163 PH13

A-79 PG14 B-162 PH14

A-80 PG15 B-161 PH15

A-81 5.0V_SR B-160 3.3V_SR

A-82 5.0V_SR B-159 3.3V_SR

A-83 5.0V_SR B-158 3.3V_SR

A-84 5.0V_SR B-157 3.3V_SR

A-85 PI0 B-156 PJ0

A-86 PI1 B-155 PJ1

A-87 PI2 B-154 PJ2

A-88 PI3 B-153 PJ3

A-89 PI4 B-152 PJ4

A-90 PI5 B-151 PJ5

A-91 PI6 B-150 PJ6

A-92 PI7 B-149 PJ7

A-93 PI8 B-148 PJ8

A-94 PI9 B-147 PJ9

A-95 PI10 B-146 PJ10

A-96 PI11 B-145 PJ11

A-97 PI12 B-144 PJ12

A-98 PI13 B-143 PJ13

A-99 PI14 B-142 PJ14

A-100 PI15 B-141 PJ15

A-101 N.C. B-140 N.C.

A-102 N.C. B-139 N.C.

A-103 N.C. B-138 N.C.

A-104 N.C. B-137 N.C.

A-105 PK0 B-136 PL0

A-106 PK1 B-135 PL1

A-107 PK2 B-134 PL2

A-108 PK3 B-133 PL3

A-109 PK4 B-132 PL4

A-110 PK5 B-131 PL5

A-111 PK6 B-130 PL6

A-112 PK7 B-129 PL7

A-113 PK8 B-128 PL8


UM2740 - Rev 1 page 22/45


A-114 PK9 B-127 PL9

A-115 PK10 B-126 PL10

A-116 PK11 B-125 PL11

A-117 PK12 B-124 PL12

A-118 PK13 B-123 PL13

A-119 PK14 B-122 PL14

A-120 PK15 B-121 PL15

A-121 5.0V_LR B-120 5.0V_LR

A-122 5.0V_LR B-119 5.0V_LR

A-123 5.0V_LR B-118 5.0V_LR

A-124 5.0V_LR B-117 5.0V_LR

A-125 PM0 B-116 PN0

A-126 PM1 B-115 PN1

A-127 PM2 B-114 PN2

A-128 PM3 B-113 PN3

A-129 PM4 B-112 PN4

A-130 PM5 B-111 PN5

A-131 PM6 B-110 PN6

A-132 PM7 B-109 PN7

A-133 PM8 B-108 PN8

A-134 PM9 B-107 PN9

A-135 PM10 B-106 PN10

A-136 PM11 B-105 PN11

A-137 PM12 B-104 PN12

A-138 PM13 B-103 PN13

A-139 PM14 B-102 PN14

A-140 PM15 B-101 PN15

A-141 RST-SW B-100 N.C.

A-142 N.C. B-99 N.C.

A-143 N.C. B-98 N.C.

A-144 N.C. B-97 N.C.

A-145 PO0 B-96 PP0

A-146 PO1 B-95 PP1

A-147 PO2 B-94 PP2

A-148 PO3 B-93 PP3

A-149 PO4 B-92 PP4

A-150 PO5 B-91 PP5

A-151 PO6 B-90 PP6

A-152 PO7 B-89 PP7

A-153 PO8 B-88 PP8

A-154 PO9 B-87 PP9


UM2740 - Rev 1 page 23/45


A-155 PO10 B-86 PP10

A-156 PO11 B-85 PP11

A-157 PO12 B-84 PP12

A-158 PO13 B-83 PP13

A-159 PO14 B-82 PP14

A-160 PO15 B-81 PP15

A-161 1.25V_SR B-80 1.25V_SR

A-162 1.25V_SR B-79 1.25V_SR

A-163 1.25V_SR B-78 1.25V_SR

A-164 1.25V_SR B-77 1.25V_SR

A-165 PQ0 B-76 PR0

A-166 PQ1 B-75 PR1

A-167 PQ2 B-74 PR2

A-168 PQ3 B-73 PR3

A-169 PQ4 B-72 PR4

A-170 PQ5 B-71 PR5

A-171 PQ6 B-70 PR6

A-172 PQ7 B-69 PR7

A-173 PQ8 B-68 PR8

A-174 PQ9 B-67 PR9

A-175 PQ10 B-66 PR10

A-176 PQ11 B-65 PR11

A-177 PQ12 B-64 PR12

A-178 PQ13 B-63 PR13

A-179 PQ14 B-62 PR14

A-180 PQ15 B-61 PR15

A-181 5.0V_SR B-60 5.0V_SR

A-182 5.0V_SR B-59 5.0V_SR

A-183 5.0V_SR B-58 5.0V_SR

A-184 5.0V_SR B-57 5.0V_SR

A-185 PS0 B-56 PT0

A-186 PS1 B-55 PT1

A-187 PS2 B-54 PT2

A-188 PS3 B-53 PT3

A-189 PS4 B-52 PT4

A-190 PS5 B-51 PT5

A-191 PS6 B-50 PT6

A-192 PS7 B-49 PT7

A-193 PS8 B-48 PT8

A-194 PS9 B-47 PT9

A-195 PS10 B-46 PT10


UM2740 - Rev 1 page 24/45


A-196 PS11 B-45 PT11

A-197 PS12 B-44 PT12

A-198 PS13 B-43 PT13

A-199 PS14 B-42 PT14

A-200 PS15 B-41 PT15

A-201 3.3V_SR B-40 3.3V_SR

A-202 3.3V_SR B-39 3.3V_SR

A-203 3.3V_SR B-38 3.3V_SR

A-204 3.3V_SR B-37 3.3V_SR

A-205 PU0 B-36 PV0

A-206 PU1 B-35 PV1

A-207 PU2 B-34 PV2

A-208 PU3 B-33 PV3

A-209 PU4 B-32 PV4

A-210 PU5 B-31 PV5

A-211 PU6 B-30 PV6

A-212 PU7 B-29 PV7

A-213 PU8 B-28 PV8

A-214 PU9 B-27 PV9

A-215 PU10 B-26 PV10

A-216 PU11 B-25 PV11

A-217 PU12 B-24 PV12

A-218 PU13 B-23 PV13

A-219 PU14 B-22 PV14

A-220 PU15 B-21 PV15

A-221 VDD_HV_IO B-20 VDD_HV_IO




A-225 PW0 B-16 PX0

A-226 PW1 B-15 PX1

A-227 PW2 B-14 PX2

A-228 PW3 B-13 PX3

A-229 PW4 B-12 PX4

A-230 PW5 B-11 PX5

A-231 PW6 B-10 PX6

A-232 PW7 B-9 PX7

A-233 PW8 B-8 PX8

A-234 PW9 B-7 PX9

A-235 PW10 B-6 PX10

A-236 PW11 B-5 PX11


UM2740 - Rev 1 page 25/45


A-237 PW12 B-4 PX12

A-238 PW13 B-3 PX13

A-239 PW14 B-2 PX14

A-240 PW15 B-1 PX15


UM2740 - Rev 1 page 26/45

5 Default jumper summary table

The following table details the DEFAULT jumper configuration of the EVB as set up on delivery.

5.1 Default jumper table - motherboardOn delivery the motherboard comes with a default jumper configuration. The table below lists and describesbriefly the jumpers on the MPC58xx motherboard and indicates which jumpers are on/off on delivery of the board.

Table 10. Default jumper table - motherboard

Jumper Default Pos PCB Legend Description

J8 Off MASTER LIN Master/Slave select

J9 Off CAP A DIS Disable capacitor circuitry for FlexRAY_A signals

J10 Off CAP A DIS Disable capacitor circuitry for FlexRAY_A signals

J11 Off CAP B DIS Disable capacitor circuitry for FlexRAY_B signals

J12 Off CAP B DIS Disable capacitor circuitry for FlexRAY_B signals

J13 Off SCI TX Connect SCI TX signal

J14 Off SCI RX Connect SCI RX signal

J15 Off LIN_EN Enable LIN PHY U50

J16 Off LIN_RX Connect LIN RX signal

J17 Off LIN_TX Connect LIN TX signal

J18 Off - Ethernet signal: RXCLK

J20 Off - Ethernet signal: CRS_LEDCFG

J21 Off CAN2_EN


1-2: WAKE to GND

3-4: STB to 5 V

5-6: EN to 5 V

J22 On - Ethernet phy power-on

J23 Off CAN-EN


1-2: WAKE to GND

3-4: STB to 5 V

5-6: EN to 5 V

J24 Off - Ethernet signal: RXER_MDIXEN

J25 Off SCI-PWR SCI phy power-on

J26 Off - Ethernet signal: RXDV_MIIMODE

J27 Off FR-A




J28 Off FR-A


1-2: 3.3V (VIO) to BGE

3-4: 3.3V (VIO) to EN

5-6: 3.3V (VIO) to STBY

7-8: GND to WAKE

UM2740Default jumper summary table

UM2740 - Rev 1 page 27/45


J29 Off FR_PWR

FlexRAY transceiver VIO selection

1-2: 12 V to VBAT

3-4: 5V_SR to VCC and VBUF

J30 Off FR_B




J31 Off FR_B


1-2: 3.3 V (VIO) to BGE

3-4: 3.3 V (VIO) to EN


7-8: GND to WAKE

J32 Off CAN21-2: PHY TX to MCU

3-4: WAKE to GND

J33 Off CAN-PWR1-2: 5V_SR to PHY U2 VCC


J34 Off -

MCAN2 signal out:

1: ERR

2: INH

J35 Off CAN1-2: 5V_SR to PHY U1 VCC


J36 Off - CAN PHY U1 signal out

J37 Off - CAN TX connect

J38 Off - CAN RX connect

J39 Off - Ethernet signal: RXD0_PHYAD1




J44 Off - Ethernet signal: COL_PHYAD0

J45 Off - Ethernet signal: TXEN

J46 Off - Ethernet signal: TXCLK

J47 Off - Ethernet signal: TXD0



J50 Off - Ethernet signal: TXD3_SNIMODE

J51 Off - Ethernet signal: MDC

J52 Off - Ethernet signal: MDIO

J53 Off RV1 Connect RV1 to analug input AN0

J54 Off ADC_VSUP Connect EVB supply voltages to analog inputs

J55 Off 12V (4.3V) Connect 12 V (scaled to 4.3 V) EVB power to analog input

J57 On ENABLE Enable 5 V linear regulator

J58 Off DISABLE Disable 1.25 V switching regulator


UM2740Default jumper table - motherboard

UM2740 - Rev 1 page 28/45



5.2 User areaThere is a rectangular prototype area on the EVB’s top right corner, consisting of a 0.1-inch pitch array ofthrough-hole plated pads. Power from all the three switching regulators is readily accessible along with GNDthrough JP1 – JP16 next to the prototyping area. This area is ideal for the addition of any custom circuitry.There are four active low user LEDs D2, D3, D4 and D5, these are driven by connecting a logic 0 signal to thecorresponding pin on 0.1” header P7 (USER LEDS). The LED inputs are pulled to VDD_HV_IO_MAIN through 10kΩ resistors.There are 4 active high pushbutton switches SW1, SW2, SW3 and SW4 which will drive 5 V onto the respectivepins on 0.1” connector P6 when pressed. The switch outputs are pulled to GND via 10 kΩ.The potentiometer RV1 can be connected to the port pin PB[0] and is adjustable between GND and 5 V from thelinear regulator. The power from all regulators can be connected to port pins as through J54:• 1-2: 1.25V_SR to PB[1]• 3-4: 3.3V_SR to PB[2]• 5-6: 5V_SR to PB[3]• 7-8: 5V_LR to PB[4]

The P12V rail from the 12 V input is scaled to 4.3 V through the voltage divider of R81 and R82 and the scaledvoltage can be connected to PB[5] via J55.

UM2740User area

UM2740 - Rev 1 page 29/45

6 BOM

Table 11. BOM

Itm Qty Reference Part number Part name Part description

1 6 C1, C2, C7, C8, C11,C12 CTAN SMD 106-A-10 10µF Tantalum Cap SMD - 10µF 10V - case A

- AVX

2 29

C3, C4, C5, C6, C51,C52, C58, C65, C66,C70, C73, C74, C75,C77, C78, C80, C83,C84, C85, C86, C87,C88, C89, C90, C91,C96, C97, C98, C100

CER SMD 104-0603V 100 nF Ceramic Cap. SMD - 100nF (0.1µF) 50V- X7R - 0603

3 2 C9, C10 CER SMD 330-0603 33pF Ceramic cap. 33 pF 50 V C0G SMD0603

4 1 C13 CTAN SMD 686-E-25 68µF Tantalum cap. SMD 68µF 25 V CASE-E- AVX TPME686K025R0045

5 3 C14, C15 ,C18 EEEFC1V101AP 100µF Electrolytic cap. 100µF 35V SMD -PANASONIC EEEFC1V101AP

6 1 C16 EEFSX0E391XE 390µFElectrolytic cap. 390µF 2,5V SMDLOW ESR (6mR) - PANASONIC

EEFSX0E391XE

7 1 C17 CER 501000-151 1000µF Electrolytic capacitor 1000µF 50V

8 9C50, C54, C59,

C72, C76, C79, C81,C82,C99

GMC10X7R102J50NT-LF 1nF Ceramic cap. 1nF 50V 5% SMD 0603 -MURATA GMC10X7R102J50NT-LF

9 3 C57,C60,C95 CER SMD 103-0603 10 nF Ceramic cap. 10nF=10000pF 50V X7RSMD0603

10 4 C61, C64,C67, C69 CER SMD 100-0603A 10 pF Ceramic cap. 10pF 100V 2% C0G SMD0603 - AVX 06031A100GAT2A

11 2 C62, C68 CER SMD 472-0603V 4,7 nF Ceramic cap. 4,7nF 100V X7R SMD0603

12 1 C71 CER SMD 474-0603X 470 nF Ceramic cap. 470nF SMD 0603 16VX7R

13 2 C92, C93 CER SMD 225-0603 2.2µF Cap. CER 2,2 uF 16 V SMD 0603 X5R

14 1 C94 GCM188R71E105KA64 1µFCeramic cap. 1µF 25V X7R10% SMD0603 - MURATAGCM188R71E105KA64

15 1 D1 GF1A-E3/67A GF1A DIODE GF1A-E3/67A 1A 50V SMDD0214BA - VISHAY

16 4 D2, D3, D4, D5 LED SMD YELLOW-1206 Yellow led Yellow led smd 1206

17 4 D6, D7, D8, D10 DB130LB-SMD B130LB-13 DIODE Rect. B130LB - 13 1A 30 V SMDSMB

18 4 D9, D11, D12, D13 LED SMD GREEN-1206 Led green LED SMD GREEN 1206 - 0805

19 1 F1 FUS 5X20-1,5AR Fuse Holder FUSE 5X20 1,5A Fast

20 15

GT1, GT2, GT3, GT4,GT5, GT6, GT7, GT8,

GT9, GT10, GT11,TP14, TP15, TP16,

TP17

TEST 1-SMD TEST POINT SOLDERING POINT SMD KEYSTONEK5015

UM2740BOM

UM2740 - Rev 1 page 30/45


21 16

JP1, JP2, JP3, JP4,JP5, JP6, JP7, JP8,

JP9, JP10, JP11,JP12, JP13, JP14,

JP15, JP16

SAM- HTSW10107SMS HDR 1X1 HDR 1X1 TH -- 330H AU 100L

22 2 J1, J3 MOLEX2P-39291028 Cap. PLUG 2 CONN MOLEX 2P MALE 39291028

23 4 J2, J5, J6, J19 F 9 POLES 90 DB9 CONN 9 POLI 90 CS FEMALE

24 1 J4 MOLEX 4P-39295043 Cap. PLUG 4 CONN MOLEX 4P MALE 39295043

25 1 J7 J1011F21PNL RJ45-8 Ethernet Connector RJ45 -J1011F21PNL

26 37

J8, J9, J10, J11, J12,J13, J14, J15, J16,J17, J18, J20, J24,J25, J26, J34, J36,J39, J40, J41, J42,

J44, J45, J46, J47 J48,J49, J50, J51, J52,

J53, J55, J58, J59, J60J62, J64

SAM-TMM10202GS HDR 1X2 CONN Samtec 1X2P TMM-102-02-G-S

27 2 J22, J57 SAM-TMM10202GS HDR 1X2 CONN Samtec 1X2P TMM-102-02-G-S -NORMALLY CLOSED

28 5 J21, J23, J27, J29, J30 SAM-TMM10302GD HDR 2X3 CONN Samtec 2X3P TMM-103-02-G-D

29 3 J28, J31, J54 SAM-TMM10402GD HDR 2X4 CONN Samtec 2X4P TMM-104-02-G-D

30 3 J32, J33, J35 SAM-TMM10202GD HDR 2X2 CONN Samtec 2X2P TMM-102-02-G-D

31 4 J37, J38, J61, J63 SAM-TMM10302GS HDR 1X3 CONN Samtec 1X3P TMM-103-02-G-S

32 2 J43, J56 SAM-QTH12002LDA QTH-120-02-L-D- A CONN Samtec 120X2P SMDQTH-120-02-L-D-A

33 2 L1, L2 DLW43SH101XK2 100µH Inductor SMD 100µH 1812 Murata -DLW43SH101XK2

34 2 L3, L4 IND SMD 47UH-SH 47µH Inductor 47µH SMD SHIELDED PWR

35 1 L5 IND SMD 68UH-SH 68µH Inductor 68µH SMD SHIELDED PWR -C.E.T. DR125/127-680-R

36 1 L6 RCH664NP-220K 22µH Inductor 22µH 1,27A - SUMIDARCH664NP-220K

37 2 P1, P2 MOLEX53047-0210 CONN 1X2 MOLEX Connector 53047-0210

38 3 P3, P6, P7 SAM-TSW10407GS HDR 1X4 CONN Samtec 1X4P TSW-104-07-G-S

39 2 P4, P5 SAM-HTSW10307SS HDR 1X3 CONN Samtec 1X3P HTSW-103-07-S-S

40 24

P8, P9, P10, P11, P12,P13, P14, P15, P16,P17, P18, P19, P20,P21, P22, P23, P24,P25, P27, P28, P29,

P30, P31, P32

SAM-TSW10907SD HDR 2X9 CONN Samtec 9X2P TSW-109-07-S-D

41 1 P26 RAPC722X CON 1 PWR Power connector

42 1 P33 TYCO-1437671-1 CON 2 TB CONN TYCO 2 POS. 1437671-1

43 1 QZ1 FOXSLF/250F-20 25MHz Crystal 25MHz PTH HC49 - FOXELECTRONICS FOXSLF/250F-20

44 1 Q2 TRMMBT3904-SMD MMBT3904LT1G TRANSISTOR MMBT3904 SMD NPNSOT23

45 1 RN1 RRSMD-49R9-1206 49R9 Resistor array 49R9 SMD CASE 1206SERIE CAY 16

UM2740BOM

UM2740 - Rev 1 page 31/45


46 3 RN2, RN50, RN51 RRSMD-103-1206 10 K Resistor array 10K SMD CASE 1206SERIE CAY 16

47 1 RN55 RRSMD-471-1206 470R Resistor array 470R SMD CASE 1206SERIE CAY 16

48 3 RN52, RN53, RN54 RRSMD-220-0804 22R Resistor array 22R SMD CASES 0804SERIES CAY 10

49 1 RV1 RTR-3310Y-2K 2 K TRIMMER 2 K PTH 3310Y-001-202LBOURNS

50 3 R50, R81, R83 RESMD102-0603 1 K RESISTANCE SMD 1 K 1/16 W 1%0603

51 1 R51 RESMD103-0603 10 K Resistor SMD 10K 1/10W 1% 0603

52 4 R52, R53, R56, R61 RESMD470-0603 47R Resistor SMD 47R 1/10 W 1% 0603

53 2 R54, R55 RESMD2490-0603 249R Resistor SMD 249R 1/10 W 1% 0603

54 4 R57, R58, R59, R60 RESMD60R4-805 60R4 Resistor SMD 60R4 1/10 W 1% 0805

55 2 R62,R63 RESMD473-0603 47 K Resistor SMD 47 K 1/16 W 1% 0603

56 14

R64, R67, R68, R69,R70, R71, R72, R73,R74, R76, R77, R78,

R79, R80

RESMD222-0603 2K2 Resistor SMD 2K2 1/16 W 1% 0603

57 1 R65 RESMD472-0603 4K7 Resistor SMD 4K7 1/10 W 1% 0603

58 1 R66 RESMD152-0603 1K5 Resistor SMD 1K50 1/10 W 1% 0603

59 1 R75 RESMD220-0603 22R Resistor SMD 22R 1/10 W 1% 0603

60 4 R82, R84, R88, R168 RESMD561-0603 560R Resistor SMD 560R 1/10 W 1% 0603

61 1 R85 RESMD33R2-0603 33R2 Resistor SMD 33R2 1/10 W 1% 0603

62 1 R87 RESMD271-0603 270R Resistor SMD 270R 1% 0603

63 1 R167 RESMD101-0603 100R Resistor SMD 100R 1/8 W 1% 0603

64 4 SW1, SW2, SW3, SW4 PULS-B3WN-6002 B3WN-6002 Switch B3WN-6002 OMRON

65 1 SW5 G-107-0513 CW G-107-0513 Inductor G-107-0513 CW INDUSTRIES

66 13

TP1, TP2, TP3, TP4,TP5, TP6, TP7, TP8,

TP9, TP10, TP11,TP12, TP13

TJA1041T-SMD TEST POINT IC TJA1041T SMD SO-14 NXP-Philips

67 2 U1, U2 TJA1041T-SMD TJA1041T

68 1 U3 MAX3221-SMD MAX3221 IC MAX3221ECAE+ SMD SSOP-16

69 2 U4, U5 TJA1080T-SMD TJA1080TS/N IC TJA1080T SMD SSOP-20

70 1 U6 DP83848CVV-SMD 10/100 single phy IC DP83848CVV/NOPB SMD LQFP48

71 1 U7 LM2937-5,0-SMD LM2937-5.0 VOLTAGE REG. LM2937IMP-5,0 SMDSOT223

72 1 U8 LM2676S-5.0-SMD LM2676S-5.0 VOLTAGE REG. LM2676S-5,0 SMDTO263-8

73 1 U9 LM2676S-3,3-SMD LM2676S-3.3 VOLTAGE REG. LM2676S-3,3 SMDTO263-8

74 1 U10 LM2676S-ADJ-SMD LM2676S-ADJ VOLTAGE REG. LM2676S-ADJ SMDTO263-8

75 1 U50 MC33661DR2-SMD MC33661PEF IC XCVR LIN 10-20KBIT/S 6-18V SO8

UM2740BOM

UM2740 - Rev 1 page 32/45

7 Schematic

Figure 13. Power

Switching Regulators

3.3V Switching Regulator

5V Switching Regulator

Input, Linear and Switchers

1.25V Switching Regulator

5V Linear Regulator

2 LeverConnector

2.1mm BarrelConnector

POWER SWITCH

Power s upply input and filter

GND Test Points

Protoype Area Reference PointsGND

1.25V_SR

P12V 5.0V_LR

GND

GND

P12V

GND

GND

GND

1.25V_SR 3.3V_SR 5.0V_SR

5.0V_SR

GND

3.3V_SR

GND

P12V

3.3V_SR

J P11

HDR 1X1

DNP 1

R167100

GT6

1

J P13

HDR 1X1

DNP 1

L4 47UH

C97 0.1UF

D13LED GREEN

AC

D10B130LB-13

AC

J P7

HDR 1X1

DNP 1

GT8

1

C99

1000PF

L5 68UH

J 57

HDR 1X2

1 2

D7B130LB-13

AC

GT2

1

C95 0.01UF

J P2

HDR 1X1

DNP 1

J P9

HDR 1X1

DNP 1

GT1

1

J P5

HDR 1X1

DNP 1

C96 0.1UF

J P16

HDR 1X1

DNP 1

P26CON_1_PWR

123

J 60HDR 1X2

12

R88

560

GT5

1

+ C13

68UF

P33CON 2 TB

A1

B2

R84

560

C91

0.1UF

U7

LM2937-5.0

VIN1

VO3

GN

D2

GN

D4

C92

2.2uF

TP141

L6 22UH

J P12

HDR 1X1

DNP 1

R83

1.0K

D12

LED GREEN

AC

TP161

J P14

HDR 1X1

DNP 1

GT7

1

J P8

HDR 1X1

DNP 1J P4

HDR 1X1

DNP 1

GT11

1

F1

Fus e Holder

1 2

U10

LM2676S-ADJ

INPUT2

SW_OUT1

C_BOOST3

GN

D4

TAB

8

FEEDBACK6

ON/OFF7

NC5

U8

LM2676S-5.0

INPUT2

SW_OUT1

C_BOOST3

GN

D4

TAB

8

FEEDBACK6

ON/OFF7

NC5

R85 33.2

D9

LED GREEN

AC R87

270.0

U9

LM2676S-3.3

INPUT2

SW_OUT1

C_BOOST3

GN

D4

TAB

8

FEEDBACK6

ON/OFF7

NC5

+ C15

100uF

J P1

HDR 1X1

DNP 1

J 59HDR 1X2

12

R168

560

C94

1uF

D8B130LB-13

AC

J P10

HDR 1X1

DNP 1

+ C16390uF

GT3

1

TP171

TP151

J P6

HDR 1X1

DNP 1

D6B130LB-13

AC

+ C17

1000UF+ C14

100uF

GT9

1

SW5G-107-0513

1 34 2

5

+ C18

100uF

GT10

1

J 58HDR 1X2

12

C98

0.1UF

L3 47UH

J P3

HDR 1X1

DNP 1

C90

0.1UF

J P15

HDR 1X1

DNP 1

Q2MMBT3904LT1G

23

1

GT4

1

C93

2.2uF

D11

LED GREEN

AC

N2 6 4 2 9 3 4 1

VSwitched VFus ed12V-IN

UM

2740 - Rev 1

page 33/45

UM

2740Schem

atic

Figure 14. Mother board connector

PortA

RST-SW is the signal coming from the reset switch(on daughter card).RST-MCU is connected to ESR0 and PORST viajumper (on daughter card).

PortB

PortM PortN PortO PortP PortR PortQ PortS PortT PortU PortV PortW PortX

PortD PortE PortF PortG PortH PortIPortC PortJ PortK PortL

GND GND

3.3V_SR1.25V_SR 5.0V_LR5.0V_SR VDD_HV_IO_MAIN

GNDGND

VDD_HV_IO_FLEX

PA[0..15](pg5,9) PB[0..15](pg9,10)

PM[0..15](pg8,9) PN[0..15](pg9) PO[0..15](pg9) PP[0..15](pg9) PR[0..15](pg9) PQ[0..15](pg9) PS[0..15](pg9) PT[0..15](pg9) PU[0..15](pg9) PV[0..15](pg9) PW[0..15](pg9) PX[0..15](pg9)

PD[0..15](pg6,9) PE[0..15](pg5..9) PF[0..15](pg9) PG[0..15](pg5,9) PH[0..15](pg7,9) PI[0..15](pg9)PC[0..15](pg5,8,9) PJ [0..15](pg9) PK[0..15](pg8,9) PL[0..15](pg9)

RST-SW(pg8)

J 43B

QTH-120-02-L-D-A

SH1SH1SH2SH2SH3SH3SH4SH4SH5SH5SH6SH6SH7SH7SH8SH8

SH9SH9

121121123123125125127127129129131131133133135135137137139139141141143143145145147147149149151151153153155155157157159159161161163163165165167167169169171171173173175175177177179179181181183183185185187187189189191191193193195195197197199199201201203203205205207207209209211211213213215215217217219219221221223223225225227227229229231231233233235235237237239239

SH16SH16

SH15SH15

SH14SH14

SH13SH13

SH12SH12

SH11SH11

SH10SH10

122122 124124 126126 128128 130130 132132 134134 136136 138138 140140 142142 144144 146146 148148 150150 152152 154154 156156 158158 160160 162162 164164 166166 168168 170170 172172 174174 176176 178178 180180 182182 184184 186186 188188 190190 192192 194194 196196 198198 200200 202202 204204 206206 208208 210210 212212 214214 216216 218218 220220 222222 224224 226226 228228 230230 232232 234234 236236 238238 240240

J 56A

QTH-120-02-L-D-A

11

33

55

77

99

1111

1313

1515

1717

1919

2121

2323

2525

2727

2929

3131

3333

3535

3737

3939

4141

4343

4545

4747

4949

5151

5353

5555

5757

5959

6161

6363

6565

6767

6969

7171

7373

7575

7777

7979

8181

8383

8585

8787

8989

9191

9393

9595

9797

9999

101101

103103

105105

107107

109109

111111

113113

115115

117117

119119

22

44

66

88

1010

1212

1414

1616

1818

2020

2222

2424

2626

2828

3030

3232

3434

3636

3838

4040

4242

4444

4646

4848

5050

5252

5454

5656

5858

6060

6262

6464

6666

6868

7070

7272

7474

7676

7878

8080

8282

8484

8686

8888

9090

9292

9494

9696

9898

100100

102102

104104

106106

108108

110110

112112

114114

116116

118118

120120

J 56B

QTH-120-02-L-D-A

SH1SH1

SH2SH2

SH3SH3

SH4SH4

SH5SH5

SH6SH6

SH7SH7

SH8SH8

SH9SH9

121121

123123

125125

127127

129129

131131

133133

135135

137137

139139

141141

143143

145145

147147

149149

151151

153153

155155

157157

159159

161161

163163

165165

167167

169169

171171

173173

175175

177177

179179

181181

183183

185185

187187

189189

191191

193193

195195

197197

199199

201201

203203

205205

207207

209209

211211

213213

215215

217217

219219

221221

223223

225225

227227

229229

231231

233233

235235

237237

239239

SH16SH16SH15SH15SH14SH14SH13SH13SH12SH12SH11SH11SH10SH10

122122

124124

126126

128128

130130

132132

134134

136136

138138

140140

142142

144144

146146

148148

150150

152152

154154

156156

158158

160160

162162

164164

166166

168168

170170

172172

174174

176176

178178

180180

182182

184184

186186

188188

190190

192192

194194

196196

198198

200200

202202

204204

206206

208208

210210

212212

214214

216216

218218

220220

222222

224224

226226

228228

230230

232232

234234

236236

238238

240240

J 43A

QTH-120-02-L-D-A

1133557799111113131515171719192121232325252727292931313333353537373939414143434545474749495151535355555757595961616363656567676969717173737575777779798181838385858787898991919393959597979999101101103103105105107107109109111111113113115115117117119119

22 44 66 88 10

10 1212 1414 1616 1818 2020 2222 2424 2626 2828 3030 3232 3434 3636 3838 4040 4242 4444 4646 4848 5050 5252 5454 5656 5858 6060 6262 6464 6666 6868 7070 7272 7474 7676 7878 8080 8282 8484 8686 8888 9090 9292 9494 9696 9898 100

100 102102 104104 106106 108108 110110 112112 114114 116116 118118 120120

PW0PW2PW4PW6PW8PW10PW12PW14

1.25V_SR 1.25V_SR

PA1

PA5PA7

PA3

PA9PA11PA13PA155.0V_SR

1.25V_SR

5.0V_SR

PA0PA1PA2PA3PA4PA5PA6PA7

PA[0..15]

PA8PA9PA10PA11PA12PA13PA14PA15

PB0PB1PB2PB3PB4PB5PB6PB7

PB[0..15]

PB8PB9PB10PB11PB12PB13PB14PB15

PM0PM1PM2PM3PM4PM5PM6PM7

PM[0..15]

PM8PM9PM10PM11PM12PM13PM14PM15

PN0PN1PN2PN3PN4PN5PN6PN7

PN[0..15]


PO0PO1PO2PO3PO4PO5PO6PO7

PO[0..15]

PO8PO9PO10PO11PO12PO13PO14PO15

PP0PP1PP2PP3PP4PP5PP6PP7

PP[0..15]

PP8PP9PP10PP11PP12PP13PP14PP15

PR0PR1PR2PR3PR4PR5PR6PR7

PR[0..15]

PR8PR9PR10PR11PR12PR13PR14PR15

PQ0PQ1PQ2PQ3PQ4PQ5PQ6PQ7

PQ[0..15]

PQ8PQ9PQ10PQ11PQ12PQ13PQ14PQ15

PS0PS1PS2PS3PS4PS5PS6PS7

PS[0..15]

PS8PS9PS10PS11PS12PS13PS14PS15

PT0PT1PT2PT3PT4PT5PT6PT7

PT[0..15]

PT8PT9PT10PT11PT12PT13PT14PT15

PU0PU1PU2PU3PU4PU5PU6PU7

PU[0..15]

PU8PU9PU10PU11PU12PU13PU14PU15

PV0PV1PV2PV3PV4PV5PV6PV7

PV[0..15]

PV8PV9PV10PV11PV12PV13PV14PV15


PW[0..15]


PX0PX1PX2PX3PX4PX5PX6PX7

PX[0..15]

PX8PX9PX10PX11PX12PX13PX14PX15

PD0PD1PD2PD3PD4PD5PD6PD7

PD[0..15]

PD8PD9PD10PD11PD12PD13PD14PD15

PE0PE1PE2PE3PE4PE5PE6PE7

PE[0..15]

PE8PE9PE10PE11PE12PE13PE14PE15

PF0PF1PF2PF3PF4PF5PF6PF7

PF[0..15]

PF8PF9PF10PF11PF12PF13PF14PF15

PG0PG1PG2PG3PG4PG5PG6PG7

PG[0..15]

PG8PG9PG10PG11PG12PG13PG14PG15

PH0PH1PH2PH3PH4PH5PH6PH7

PH[0..15]

PH8PH9PH10PH11PH12PH13PH14PH15

PI0PI1PI2PI3PI4PI5PI6PI7

PI[0..15]

PI8PI9PI10PI11PI12PI13PI14PI15

PC0PC1PC2PC3PC4PC5PC6PC7

PC[0..15]

PC8PC9PC10PC11PC12PC13PC14PC15

PJ 0PJ 1PJ 2PJ 3PJ 4PJ 5PJ 6PJ 7

PJ [0..15]


PK0PK1PK2PK3PK4PK5PK6PK7

PK[0..15]


PL0PL1PL2PL3PL4PL5PL6PL7

PL[0..15]

PL8PL9PL10PL11PL12PL13PL14PL15

1.25V_SR

5.0V_LR

3.3V_SR5.0V_SR

VDD_HV_IO_MAINVDD_HV_IO_MAIN

VDD_HV_IO_MAIN

1.25V_SRPA0PA2PA4PA6PA8PA10PA12PA145.0V_SR5.0V_SRPC0PC2PC4PC6PC8PC10PC12PC143.3V_SR3.3V_SRPE0PE2PE4PE6PE8PE10PE12PE141.25V_SR1.25V_SRPG0PG2PG4PG6PG8PG10PG12PG145.0V_SR5.0V_SRPI0PI2PI4PI6PI8PI10PI12PI14


PC1PC3PC5PC7PC9PC11

PC15PC13

3.3V_SR3.3V_SR

PE3PE1

PE5PE7

PE11PE9

PE13PE15

1.25V_SR1.25V_SR

PG1PG3PG5PG7PG9PG11

PG15PG13

5.0V_SR5.0V_SR

PI3PI1

PI5PI7

PI11PI9

PI13PI15

PK3PK1

PK5PK7

PK11PK9

PK13PK15

5.0V_LR5.0V_LRPM0PM2PM4PM6PM8PM10PM12PM14RST-SW

PO0PO2PO4PO6PO8PO10PO12PO141.25V_SR1.25V_SRPQ0PQ2PQ4PQ6PQ8PQ10PQ12PQ145.0V_SR5.0V_SRPS0PS2PS4PS6PS8PS10PS12PS143.3V_SR3.3V_SRPU0PU2PU4PU6PU8PU10PU12PU14


5.0V_LR5.0V_LRPM1PM3PM5PM7PM9PM11PM13PM15

PO1PO3PO5PO7PO9PO11PO13PO151.25V_SR1.25V_SRPQ1PQ3PQ5PQ7PQ9PQ11PQ13PQ155.0V_SR5.0V_SRPS1PS3PS5PS7PS9PS11PS13PS153.3V_SR3.3V_SRPU1PU3


PU5PU7PU9PU11PU13PU15


PX1

PX5PX7PX9PX11PX13PX15

PX3

PV3PV1

PV5PV7PV9PV11PV13PV15

PT1

PT5PT3

PT7PT9PT11PT13PT15

PR1

PR11PR13PR15

PR5PR7

PR3

PR9

PP1

PP5PP7PP9PP11PP13PP15

PP3


5.0V_LR5.0V_LR

1.25V_SR1.25V_SR

5.0V_SR5.0V_SR

3.3V_SR3.3V_SR

PL1

PL5PL3

PL7PL9PL11PL13PL15

PJ 1

PJ 5PJ 7PJ 9PJ 11

PJ 3

PJ 13PJ 15

PH1

PH5PH7

PH3

PH9PH11PH13PH153.3V_SR

PF1

PF11PF13PF151.25V_SR

PF3PF5PF7PF9

PD1

PD5PD7PD9PD11PD13

PD3

PD153.3V_SR

PB1

PB5PB7PB9

PB3

PB11PB13PB155.0V_SR

1.25V_SR

5.0V_SR

3.3V_SR

1.25V_SR

3.3V_SR

1.25V_SR

PL2PL4PL6

PL0

PL8PL10PL12PL14


PH2PH4PH6PH8

PH0

PH10PH12PH143.3V_SR

PF0

PF10PF12PF141.25V_SR

PF2PF4PF6PF8

PD0PD2PD4PD6PD8PD10PD12PD143.3V_SR

PB0PB2PB4PB6PB8PB10PB12PB145.0V_SR

1.25V_SR

5.0V_SR

3.3V_SR

1.25V_SR

3.3V_SR

1.25V_SR

PX4

PX0

PR10

PR2

5.0V_LR

PT6

PT2

5.0V_SR

PN8

3.3V_SR

PT14

PP4

PP0

PV10

PP12

VDD_HV_IO_MAIN

PR8

PR4

PR0

PX14

PT4

PT0

5.0V_SR

PN6

PN2

PT12

PV8

PP10

VDD_HV_IO_MAIN

PR6

1.25V_SR

PX12

PX8

PR14

PN4

PN0

PT10

PN12

PV6

PV2

PP8

PV14

1.25V_SR

PX10

PX6

PX2

PR12

5.0V_LR

PT8

PN14

PN10

PV4

PV0

3.3V_SR

PP6

PP2

PV12

PP14

VDD_HV_IO_FLEX VDD_HV_IO_FLEXVDD_HV_IO_FLEX

VDD_HV_IO_FLEX

UM

2740 - Rev 1

page 34/45

UM

2740Schem

atic

Figure 15. CAN interface

1

(CNB-TX)

(CNB-RX)

(CNA-RX)

CAN (MCAN1/TTCAN)

(CNA-TX)

MCAN2

TTCAN-RX

MCAN1-RX

MCAN1-TX

TTCAN-TX

GND

5.0V_SR

GND

CAN-12V

CAN-5VP12V

GND

CAN-12V CAN-5V

GND

GND

GND

GND

5.0V_SR

GND

GND

GND

GND

GND

GND

GND

GND

5.0V_SR

GND

VDD_HV_IO_MAIN

VDD_HV_IO_MAIN

PC9(pg4,9)

PC8(pg4,9)

PE5(pg4,9)

PG14(pg4,9)

PA10(pg4,9)

PA11(pg4,9)

P4123

C82

1000PF

R5760.4

C74

0.1UF

R5860.4

R6060.4

J 36

HDR 1X2

12

J 321 23 4

C77

0.1UF

P5123

J 34

HDR 1X2

12

U2

TJ A1043T

INH7

WAKE9

STB14

EN6

TXD1

ERR8

RXD4

GN

D2

SPLIT11

CANH13

CANL12

VI/O

5

VB

AT

10

VC

C3

J 5

DB9

594837261

M2

M1

C570.01UF

J 38

HDR_1X3

1

2

3

J 351 23 4

C81

1000PF

C79

1000PF

C600.01UF

J 6

DB9

594837261

M2

M1C54

1000PF

R5960.4

J 331 23 4

C78

0.1UF

C73

0.1UF

C59

1000PF

C52

0.1UF

J 37

HDR_1X3

1

2

3

J 231 23 4

65

J 211 23 4

65

U1

TJ A1043T

INH7

WAKE9

STB14

EN6

TXD1

ERR8

RXD4

GN

D2

SPLIT11

CANH13

CANL12

VI/O

5

VB

AT

10

VC

C3

C58

0.1UF

C76

1000PF

MCAN1-CANHMCAN1-CANL

TTCAN-CANHTTCAN-CANL

TTCAN-TXTTCAN-RX

MCAN1-TXMCAN1-RX

PC8

PC9

PG14

PA11

PE5

PA10

UM

2740 - Rev 1

page 35/45

UM

2740Schem

atic

Figure 16. SPI/RS232 and LIN interface

1

(TXD, LINFlexD_1)

(RXD, LINFlexD_1)

eSCI / RS232(us ing LINFlexD_2)

Master Mode PullupEnableLINFlexD_1

(TXD, LINFlexD_2)

(RXD, LINFlexD_2)

e S C I / R S 2 3 2 a n d L I N P H Y S I C A L I N T E R F A C E S

LIN Molex Connector

4Pin Header

IC is 3.3V & 5V compatible

IC is 3.3V & 5V compatible

P12V

GND

VDD_HV_IO_MAIN

GND

GND

GNDGND

GND

GND

GND

VDD_HV_IO_MAIN

GND

GND

VDD_HV_IO_MAIN

PE[0..15](pg4,5,7..9)

PD[0..15](pg4,9)

P3

HDR_1X4

1

32

4

R51 10.0K

J 8

HDR 1X2

1 2

C100

0.1UF J 19

DB9

594837261

M2

M1J 13 HDR 1X2

1 2

D1

GF1A

A C

C72

1000PF

J 17 HDR 1X21 2

J 14 HDR 1X2

1 2

J 16 HDR 1X2

1 2

C75

0.1UF

C50

1000PF

J 25

HDR 1X2

12

U50

MC33661PEF

RXD1

EN2

WAKE3

TXD4

GND5LIN6VSUP7INH8

C51

0.1UF

C70

0.1UF

C71

0.47UF

J 4

CON PLUG 4

1234

U3TR3221

V+3

C1+2

C1-4

EN1

FORCEOFF16

VCC15

GND14

V-7

C2+5

C2-6

T1OUT13

R1IN8

T1IN11

R1OUT9

INVALID10

FORCEON12

R50 1.0K

J 15

HDR 1X2

1 2

C80

0.1UF

SCI-RX

PE6

PE7

LINFlex-RX

PD15

LINC-LIN

SCI-TXPD14

RS232A-TX

RS232A-RX

RS232-1

RS232-4

LINC-VSUP

LINFlex-TX

RS232-3

N1 6 9 6 6 2 9 4

RS232-5

RS232-VCC

UM

2740 - Rev 1

page 36/45

UM

2740Schem

atic

Figure 17. FlexRay

FR_DBG[0]FR_DBG[1]FR_DBG[2]FR_DBG[3]-> connect to test points

J36 Default:Across pin1 & pin2Across pin3 & pin4Across pin5 & pin6Across pin7 & pin8

J31 Default:Across pin1 & pin2Across pin3 & pin4Across pin5 & pin6Across pin7 & pin8

J34 Default:Across pin1 & pin2Across pin3 & pin4Across pin5 & pin6

J29 Default:Across pin1 & pin2Across pin3 & pin4Across pin5 & pin6

FlexRay_A

FlexRay_B

NormalEN STBN1

SleepGo to SleepRec Only 0

111

MODE

0 00

VIO Selection Jumper

BM_A

BM_B

BP_A

BP_B

GND

GND

P12V

GND

GND

GND

GND

GND

GND

GND

GND

5.0V_SR

GND

VDD_HV_IO_FLEX

PE[0..15](pg4..6,8,9)

PH[0..15](pg4,9)

TP8

J 29 HDR 2X31 23 4

65

TP10

TP12

U5

TJ A1080TS/N

TRXD011

TRXD110

TXD5

TXEN6

BGE8

STBN9

EN3

WAKE15

INH21

INH12

BP18

BM17

RXD7

ERRN13

RXEN12

VIO

4

VC

C19

VB

UF

20

VB

AT

14G

ND

16

TP13

J 2

DB9

594837261

M2

M1

J 281 23 45 67 8

TP11

C5

0.1UF

L1

DLW43SH

21

4 3

J 1

CON PLUG 2

DNP

12

P112

C6

0.1UF

J 311 23 45 67 8

R5347.0

R62 47K

J 9HDR 1X2

12

J 30

HDR 2X3

1 23 4

65

RN51

10K

1234 5

678

J 3

CON PLUG 2

DNP

12

J 10HDR 1X2

12

P212

C62 4700PF

L2

DLW43SH

21

4 3

R6147.0

+C7

10UF

J 11HDR 1X2

12

C68 4700PF

TP5

U4

TJ A1080TS/N

TRXD011

TRXD110

TXD5

TXEN6

BGE8

STBN9

EN3

WAKE15

INH21

INH12

BP18

BM17

RXD7

ERRN13

RXEN12

VIO

4

VC

C19

VB

UF

20

VB

AT

14G

ND

16

C61

10 PF

C4

0.1UF

J 12HDR 1X2

12

TP7

R63 47K

J 271 23 4

65

TP1

R5247.0

+C2

10UF

TP2

+C1

10UF

C69

10 PF

RN50

10K

1234 5

678

TP6

+C8

10UF

TP3R5647.0

TP4

C3

0.1UF

C64

10 PF

C67

10 PF

PE9

PE10

PE11

PE12

FRA-WAKE

FRA-INH1

PH7

FR-12V

FRB-J RXD

FR-5V

PH8

FRA-BGE

PH9

FRA-J RXD

FR-VIO

FRA-J TXD

FR-VIO

FRA-J TXEN

FRA-BM FRA-DATA-BFRA-STBN

FR-VIO

FRA-BP

FRB-INH2

PH3PH4

FRB-BGE

PH10

FRB-J TXDFRB-J TXEN

FRB-BM FRB-DATA-BFRB-STBN

FRB-BP

FRB-EN

FRB-INH1

FRB-RXEN

FRB-DATA-A

FRB-ERRN

FR-5V

FRA-EN

FRB-WAKE

FRA-INH2

FR-5V

FRA-RXEN

FRA-DATA-A

FRA-ERRN

FR-12V

FR-12V

FR-VIO

FR-VIO

UM

2740 - Rev 1

page 37/45

UM

2740Schem

atic

Figure 18. Fast Ethernet controller

ETHERNET PHYSICAL INTERFACE AND RJ45

TX Resistors: Place Close to PI

RX Resistors: Place Close to MCU

RMIIRMII

RMII

RMII

RMIIRMII

These lines need to be matched!

GND

GND

GND

GND GND

GNDGND

3.3V_SR3.3V_SR

GND GND

3.3V_SR

GND

GND

GND

GND3.3V_SR

PK14(pg4,9)

PK15(pg4,9)

PE12(pg4,7,9)

RST-SW(pg4)PM[0..15] (pg4,9)

PC[0..15] (pg4,5,9)

PA15(pg4,9)

RN53A 221 8

J 50

HD

R 1

X2

12

R76

2.2K

RN1C

49.9

36

C84

0.1UF

C88

0.1UF

R67

2.2K

J 44

HD

R 1

X2

12

RN53B 222 7

J 26

HD

R 1

X2

12

J 42

HD

R 1

X2

12

J 22

HDR 1X2

12

R73

2.2K

RN1B

49.9

27

C87

0.1UF

R65

4.70K

J 7 RJ 45-8

TD+1

TD-2

CT_33

GND_44

GND_55

CT_66

RD+7

RD-8

YA

9

YC

10

GC

11

GA

12

GND1CG1

GND2CG2

C65

0.1UF

R74

2.2K

R64

2.2K

C9

33PF

R69

2.2K

TP9

RN1D

49.9

45

J 40

HD

R 1

X2

12

R75 22

J 45

HD

R 1

X2

12

C66

0.1UF

R71

2.2K

RN54D 224 5

J 20

HD

R 1

X2

12

J 39

HD

R 1

X2

12

+C12

10UF

J 49

HD

R 1

X2

12

QZ1

25MHZ

21

C10

33PF

RN53C 223 6

R78

2.2K

J 24

HD

R 1

X2

12

J 63

HDR_1X3

1

2

3

C85

0.1UF

J 46

HD

R 1

X2

12

RN52A 221 8

RN54C 223 6

J 52

HD

R 1

X2

12

J 48

HD

R 1

X2

12

R79

2.2K

J 47

HD

R 1

X2

12

+C11

10UF

RN53D 224 5

J 64 HDR 1X212

R55

249

C83

0.1UF

R80

2.2K

RN54B 222 7

J 62

HDR 1X2

1 2

RN52C 223 6

R54

249

J 41

HD

R 1

X2

12

R70

2.2K

J 51

HD

R 1

X2

12

RN54A 221 8

C89

0.1UFR77

2.2K

R66

1.50K

RN52B 222 7

J 61

HDR_1X3

1

2

3

R72

2.2K

J 18

HD

R 1

X2

12

C86

0.1UF

R68

2.2K

RN1A

49.9

18

RN52D 224 5

dp83848c

U6 10/100 s ingle phy

RXCLK38

RS

VD

PU

221

RS

VD

PU

120

RS

VD

512

RS

VD

411

RS

VD

310

RS

VD

29

RS

VD

18

RDN13RDP14

LEDACTCOL_ANEN28

IOV

DD

33_2

48IO

VD

D33

_132

IOG

ND

_247

IOG

ND

_135

DG

ND

36A

VD

D33

22A

GN

D_2

15A

GN

D_1

19

TXD25

TXCLK1

LEDLINK_AN026

RXER_MDIXEN41

MDC31

RESET29

PWRDN_INT7

MDIO30

CRS_LEDCFG40

RXD3_PHYAD346

RXD2_PHYAD245

RXD1_PHYAD144

RXD0_PHYAD143

RXDV_MIIMODE39

TXEN2 TXD03

LEDSPEED_AN127

PFBIN237

TXD3_SNIMODE6

TXD14

RBIAS24

COL_PHYAD042

PFBIN118

PFBOUT23

X233 X134

TDN16TDP17

25MHZ_OUT25

PC12PM0PM3PM2

PC11PC10PC3PC2

PC13

PM1

PK15

PK14

PC14PC15

PM4PM5

PE12

RST-SW

PA15

UM

2740 - Rev 1

page 38/45

UM

2740Schem

atic

Figure 19. User I/O

PortO

PortR

PortK

PortM

PortP

PortL

PortI

PortJ

PortN

PortG

PortT

PortS

PortV

PortU

PortX

PortW

PortC

PortE

NOTE: All Connectors are 0.1" through-hole headers

PortH

PortD

PortA

PortB

PortQ

PortF

GNDGND

GNDGND

GND

GNDGND

GNDGND

GNDGND

GNDGND

GNDGND

GND

GNDGND

GNDGND

GNDGND

GNDGND

GNDGND

GNDGND

GNDGND

GNDGND

GND

GNDGND

GNDGND

GNDGND

GNDGND

GNDGND

GND GNDGND

GNDGND

PO[0..15](pg4)

PR[0..15] (pg4)

PK[0..15](pg4,8)

PM[0..15](pg4,8)

PP[0..15](pg4)

PI[0..15](pg4)

PJ [0..15](pg4)

PL[0..15](pg4)

PN[0..15](pg4)

PG[0..15](pg4,5)

PT[0..15] (pg4)

PS[0..15] (pg4)

PV[0..15] (pg4)

PU[0..15] (pg4)

PX[0..15] (pg4)

PW[0..15] (pg4)

PC[0..15](pg4,5,8)

PE[0..15](pg4..8)

PH[0..15](pg4,7)

PA[0..15](pg4,5)

PB[0..15](pg4,10)

PD[0..15](pg4,6)

PQ[0..15] (pg4)

PF[0..15](pg4)

P9

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P21

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P14

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P16

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P23

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P10

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P17

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P31

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P12

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P22

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P30

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P11

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P28

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P24

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P19

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P32

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P18

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P20

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P29

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P8

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P27

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P15

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P13

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

P25

HDR 2X9

1 23 4

657 89 10

11 1213 1415 1617 18

PO7

PO1

PO[0..15]

PO13

PO8

PO0

PO15

PR7

PR1

PR13

PO14

PO3

PO9PO6

PR8

PR0

PO10PO12

PO4

PO11

PR15PR14

PO2PO5

PR3

PR9PR6

PR10PR12

PR4

PR11

PR2PR5

PR[0..15]PR[0..15]

PI[0..15]

PK7

PK1

PK[0..15]

PK13

PK8

PK0

PK15PK14

PK3

PK9PK6

PK10PK12

PK4

PK11

PK2PK5

PI0

PM7

PM1

PM[0..15]

PM13

PM8

PM0

PM15PM14

PM3

PM9PM6

PM10PM12

PM4

PM11

PM2PM5

PI2PI4

PP7

PP1

PP[0..15]

PP13

PP8

PP0

PP15PP14

PP3

PP9PP6

PP10PP12

PP4

PP11

PP2

PI6

PP5

PL7

PI8PI10PI12PI14

PL1

PL[0..15]

PL13

PL8

PL0

PL15PL14

PL3

PL9PL6

PL10PL12

PL4

PL11

PL2PL5

PI1PI3PI5PI7

PJ 7

PJ 13

PJ 1

PJ [0..15]

PJ 8

PJ 0

PJ 15PJ 14

PJ 3

PJ 9PJ 6

PJ 10PJ 12

PJ 11

PJ 4PJ 2

PJ 5

PI9PI11PI13PI15

PN7

PN1

PN[0..15]

PN13

PN8

PN0

PN15PN14

PN3

PN9PN6

PN10PN12

PN4

PN11

PN2PN5

PG7

PG1

PG[0..15]

PG13

PG8

PG0

PG15PG14

PG3

PG9PG6

PG10

PT7

PT1

PG12

PG4

PG11

PT13

PT8

PT0

PG2PG5

PT15PT14

PT3

PT9PT6

PT10PT12

PT4

PT11

PT2PT5

PT[0..15]PT[0..15]

PS7

PS1

PS13

PS8

PS0

PS15PS14

PS3

PS9PS6

PS10PS12

PS4

PS11

PS2PS5

PS[0..15]PS[0..15]

PV7

PV1

PV13

PV8

PV0

PV15PV14

PV3

PV9PV6

PV10PV12

PV4

PV11

PV2PV5

PV[0..15]PV[0..15]

PU7

PU1

PU13

PU8

PU0

PU15PU14

PU3

PU9PU6

PU10PU12

PU4

PU11

PU2PU5

PU[0..15]PU[0..15]

PX7

PX1

PX13

PX8

PX0

PX15PX14

PX3

PX9PX6

PX10PX12

PX4

PX11

PX2PX5

PX[0..15]PX[0..15]

PW7

PW1

PW13

PW8

PW0

PW15PW14

PW3

PW9PW6

PW10PW12

PW4

PW11

PW2PW5

PW[0..15]PW[0..15]

PA[0..15]

PC7

PC1

PC[0..15]

PC13

PC8

PC0

PC15PC14

PC3

PC9PC6

PC10PC12

PC4

PC11

PC2PC5

PA0

PE7

PE1

PE[0..15]

PE13

PE8

PE0

PE15PE14

PE3

PE9PE6

PE10PE12

PE4

PE11

PE2PE5

PA2PA4

PH7

PH1

PH[0..15]

PH13

PH8

PH0

PH15PH14

PH3

PH9PH6

PH10PH12

PH4

PH11

PH2

PA6

PH5

PD7

PA8PA10PA12PA14

PD1

PD[0..15]

PD13

PD8

PD0

PD15PD14

PD3

PD9PD6

PD10PD12

PD4

PD11

PD2PD5

PA1PA3PA5PA7

PB7

PB13

PB1

PB[0..15]

PB8

PB0

PB15PB14

PB3

PB9PB6

PB10PB12

PB11

PB4PB2

PB5

PA9PA11PA13PA15

PQ7

PQ1

PQ13

PQ8

PQ0

PQ15PQ14

PQ3

PQ9PQ6

PQ10PQ12

PQ4

PQ11

PQ2PQ5

PQ[0..15]PQ[0..15]

PF7

PF1

PF[0..15]

PF13

PF8

PF0

PF15PF14

PF3

PF9PF6

PF10PF12

PF4

PF11

PF2PF5

UM

2740 - Rev 1

page 39/45

UM

2740Schem

atic

Figure 20. User peripherals inc. prototyping

Us er Switches

LED's are SMD (1206) Yellow

Us er LED's

OMRON B3WN-6002 Pushbutton Switch

(AN0)

AN0 Potentiometer/Filters /Voltage Monitors

(Note - This is run from linear 5.0v regulator to provide a stable input voltage)

Prototyping Area Still missing.To be added later.

(AN1)(AN2)(AN3)(AN6)

(AN35)

P12V

GND

1.25V_SR 5.0V_SR3.3V_SR 5.0V_LR

VDD_HV_IO_MAIN

VDD_HV_IO_MAIN

GND

GND

5.0V_LR

PB[0..15](pg4,9) J 53

HDR 1X2

12

R811.0K

SW1

B3WN-60021 2

RN55

10K

1234 5

678

J 55

HDR 1X2

12

SW2

B3WN-60021 2

RN2

10K

1234 5

678

SW3

B3WN-60021 2

RV12K 13

2

D2YELLOW LED

AC

SW4

B3WN-60021 2

D3YELLOW LED

ACP7

HDR_1X4

1

32

4

R82560

D4YELLOW LED

AC

P6

HDR_1X4

1

32

4

D5YELLOW LED

AC

J 541 23 45 67 8PB4

PB3PB2PB1

USR-SW2

PB5

USR-SW3USR-SW4

USR-SW1

PB0

UM

2740 - Rev 1

page 40/45

UM

2740Schem

atic

Revision history

Table 12. Document revision history

Date Version Changes

25-Jan-2021 1 Initial release.

UM2740

UM2740 - Rev 1 page 41/45

Contents

1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

1.1 Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2 License agreement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

3 Handling precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

4 Hardware description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

4.1 List of acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4.2 Modular concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4.3 Daughter card availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4.4 EVB features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4.5 Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4.6 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4.7 Power supply configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4.8 Motherboard power supply connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4.9 Regulator power jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4.10 Power switch, status LEDs and use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4.11 CAN configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.12 RS232 configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.13 LIN configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.14 FlexRAY configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.15 Ethernet configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.16 Motherboard test points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4.17 Board interface connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

5 Default jumper summary table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

5.1 Default jumper table - motherboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

5.2 User area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

6 BOM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

7 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

UM2740Contents

UM2740 - Rev 1 page 42/45

List of tablesTable 1. List of acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Table 2. Daughter card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Table 3. CAN control jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Table 4. RS232 control jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Table 5. LIN control jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Table 6. FlexRAY control jumpers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Table 7. Ethernet control jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Table 8. Test points - motherboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Table 9. Board interface connector details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Table 10. Default jumper table - motherboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Table 11. BOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Table 12. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

UM2740List of tables

UM2740 - Rev 1 page 43/45

List of figuresFigure 1. SPC58XXMB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Figure 2. Modular concept - motherboard and MCU daughter card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Figure 3. EVB functional blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Figure 4. Power supply barrel connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Figure 5. 2-lever power connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Figure 6. CAN DB9 connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Figure 7. CAN 3pin header interface connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Figure 8. RS232 physical interface connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Figure 9. LIN molex connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Figure 10. LIN 4pin header interface connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Figure 11. FlexRAY DB9 connector pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Figure 12. FlexRAY alternative connector pin-outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Figure 13. Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Figure 14. Mother board connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Figure 15. CAN interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Figure 16. SPI/RS232 and LIN interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Figure 17. FlexRay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Figure 18. Fast Ethernet controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Figure 19. User I/O. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Figure 20. User peripherals inc. prototyping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

UM2740List of figures

UM2740 - Rev 1 page 44/45

IMPORTANT NOTICE – PLEASE READ CAREFULLY

STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to STproducts and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. STproducts are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.

Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design ofPurchasers’ products.

No license, express or implied, to any intellectual property right is granted by ST herein.

Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.

ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks. All other product or servicenames are the property of their respective owners.

Information in this document supersedes and replaces information previously supplied in any prior versions of this document.

© 2021 STMicroelectronics – All rights reserved

UM2740

UM2740 - Rev 1 page 45/45

http://www.st.com/trademarks

spc58xxmb evaluation board - stmicroelectronics · 2021. 8. 5. · 4.9 regulator power jumpers....

Documents