special tools...mb - trucks, actros with air suspension, agricultural machinery art. no. 1952 001...
TRANSCRIPT
SPECIAL TOOLSFor all industries
ALL ITEMS DIRECT DELIVERY
2 SPECIAL TOOLS
Content
Chassis/Axles 3 – 19
Brakes 20 – 24
Engine 25 – 35
Wheels/Tires 36 – 37
Body 38 – 41
Universal 42 – 55
Content
Commercial vehicles:
Mercedes MAN DAF Scania VolvoIvecoRenault Vans
Trailers:Schmitz CargobullKroneKögelFliegl
Also suitable for pas-senger cars, buses and agricultural machinery.
3SPECIAL TOOLS
CHASSIS
For passenger cars and vans, in case. To remove ball joint studs from tie rods, steering knuckles, and stabilizers, incl. reinforced version for vans. Es-pecially suitable for work in hard-to-reach places.
Suitable for:Audi, VW, BMW, Citroen Jumper, Fiat Ducato, Peugeot Boxer, MB Sprinter, Renault, Rover, Saab, Volvo, buses, agricultural machinery
Art. no. 1952 001 009PU/Qty. 1
To remove ball joint studs from tie rods, steering knuckles, and stabilizers, incl. reinforced version for vans. Especially suitable for work in hard-to-reach places.
Also available individually:
BALL JOINT STUD REMOVER SET, 3-PIECE
BALL JOINT STUD REMOVER
Jaw opening Suitable for Art. No. PU Price23 x 55 mm Audi, VW, BMW, Citroen Jumper, Fiat Ducato, Peugeot
Boxer, MB Sprinter, Renault, Rover, Saab, Volvo, various Japanese passenger car brands, agricultural machinery
1952 001 010 1 89.26
28 x 55 mm Audi A4, A6, A8, VW Passat models from 1997 and Mercedes Benz, agricultural machinery
1952 001 011 1 85.8834 x 63 mm MB Sprinter, VW LT, Opel Movano, agricultural
machinery, etc.1952 001 012 1 85.88
238,99
4 SPECIAL TOOLS
CHASSIS
Especially adapted, impact-resistant design. For the removal and mounting of Cardan shafts.Suitable for: Citroen C25, Fiat Ducato, Peugeot J5, agricultural machinery
Art. no. 1952 001 017PU/Qty. 1
Length 70 mmSuitable for: Ford Transit from 1991, axle no. 34, agricultural machinery
Art. no. 1952 001 018PU/Qty. 1
Impact wrench design consisting of: deep impact sockets sizes 30, 32, 36 mm (bihex) and impact screwdriver bits 14, 17, 19 mm (hex bits) for drive shafts.Suitable for: Any type of vehicle, agricultural machinery
Art. no. 1952 001 019PU/Qty. 1
Thin-walled version of art. no. 1952 001 019. Profile and single-piece extra-short screwdriver bits. For removal and mounting.
Scope of delivery:Size 24, 27, 30, 32, 34, 36 x 85 mm (bihex socket);Size 14, 17, 19 x 43 mm (hex screwdriver bit)
Suitable for: VW (Golf IV - Polo - Passat etc.), Audi, Seat, Skoda, Opel, BMW, Mercedes, Renault, Toyota, agricultural machinery
Art. no. 1952 001 020PU/Qty. 1
DRIVE SHAFT SOCKET CV41 MM HEX, ¾" DRIVE
AXLE NUT SOCKET CV 57 MM BIHEX, ¾" DRIVE
DRIVE SHAFT SOCKET SET 6-PIECE, ½" DRIVE, BIHEX + HEX
DRIVE SHAFT IMPACT SOCKET SET 9-PIECE, ½" DRIVE, BIHEX + HEX
95.09
60.16
113.90
176.81
5SPECIAL TOOLS
CHASSIS
• Length x width: 52 x 8 mm• Inner stud Ø 61 mm• Inner Ø of base body 50 mm• Outer Ø 70 mm• For rear axles
Fig. Jaw opening Max. height Surface Drive Weight Application Type Art. No. PU1 30 mm 58 mm Burnished Hex 19 mm 1.10 kg Bolt suitable for impact
screwdrivers, pressure piece rotates on bolt.
Light trucks 3.5 – 8.8 t 1952 001 277 1
2 32 mm 90 mm Hex 26 mm 2.5 kg 1952 001 278 1
– 39 mm 58 mm Hex 26 mm 3.85 kg Trucks, e.g. MB 1424, Actros2
1952 001 279 1
Heavy-duty design, ruggedized and workshop-tested
• For pressing out ball joint studs• With hydraulic pressure spindle 10t
GROOVE LOCK NUT SOCKET, REAR AXLE¾" DRIVE, 6 STUDS
PULLER FOR TIE ROD ENDS BELL SHAPE
BALL JOINT SEPARATOR
Studs Jaw sizes Maximum Suitable for Art. No. PU Price
27-36 mm Max. 90 mm 12 t MB, e.g. ATEGO up to 17t, MAN M 2000, Iveco, Renault, Scania, Volvo, DAF. Vans, e.g. VW T4, Ford Transit, MB Sprinter, Fiat Ducato, heavy-duty passenger cars, e.g. off-road vehicles.
1952 001 076 1 413.14
35-45 mm Max. 115 mm 20 t MB, e.g. Actros, Atego from 18t, SK, O405, O405 - N (low-floor bus), MAN F 2000, TGA, low-floor articulated bus, Iveco Eurostar, Eurotech, Turbostar, Scania series 3 and 4, coaches on Scania chassis such as Icarus, DAF, Renault, Volvo.
1952 001 077 1 617.29
1 2
Art. No. Price
1952 001 277 189.411952 001 278 278.391952 001 279 341.95
119.23Suitable for: VW LT, MB Sprinter 412 D
Art. no. 1952 001 022 PU/Qty. 1
6 SPECIAL TOOLS
CHASSIS
For flat-oval axle nuts on BPW axles and ECO axle.
Suitable for: MAN, DAF 106, Scania 124 I – 144 I – etc.
Art. no. 1952 001 107PU/Qty. 1
For removal/mounting of flat-oval hub cap nuts and axle nuts.
For flat-oval grease caps.
AXLE NUT SOCKET, FLAT OVAL 36 MM HEX DRIVE, HEAVY-DUTY DESIGN
AXLE NUT SOCKET CV¾" DRIVE, 80 MM, OCTAGON, IMPACT SOCKET
HUB CAP AND AXLE NUT SOCKET ¾" / 1" DRIVE, IMPACT NUT
HUB CAP AND AXLE NUT SOCKET, FLAT OVAL¾" DRIVE, IMPACT SOCKET
Size Suitable for Art. No. PU Price65 mm BPW axles, ECO axle 9, 10, 12t 1952 001 078 1 196.2580 mm BPW axles, ECO axle 9, 10, 12t 1952 001 079 1 244.33
Size Suitable for Art. No. PU Price¾"/95 mm BPW axles 9t, 12t/10t ECO axle 1952 001 080 1 197.801"/110 mm BPW axle 12t 1952 001 081 1 203.13
Size Suitable for Art. No. PU Price65 mm BPW axles 9t, 12t and 10t ECO axle 1952 001 082 1 131.7180 mm 1952 001 083 1 139.0785 mm BPW axle 13 t ECO front axle 1952 001 084 1 145.4095 mm BPW axle 9t 1952 001 085 1 149.74110 mm BPW axle 12 t 1952 001 086 1 167.80120 mm BPW-ECO axle 1952 001 087 1 175.16
195.64
7SPECIAL TOOLS
CHASSIS
For rear-axle hubs with brake drums and wheels.
AXLE NUT SOCKET WITH OR W/O GUIDE BAND36 MM, HEX DRIVE, HEAVY-DUTY DESIGN
AXLE NUT SOCKET HEXAGON AND OCTAGON
Fig. Size Suitable for Art. No. PU Price1 85 mm SAF trailer axles 1952 001 090 1 243.81
90 mm IVECO - Cargo rear axle ´98 1952 001 091 1 366.102 95 mm DC trailer axle Dicos Trailers from 2005 with compact
bearing HUB unit (DB no. W749589000900)1952 001 093 1 431.69
98 mm IVECO Euro Cargo - rear axle type 120 E15 ´98 with double nut
1952 001 092 1 342.953 105 mm Kässbohrer/Setra coaches 1952 001 094 1 367.11
Fig. Drive Size Suitable for Art. No. PU1 ¾"/square 77 mm/hex Renault 1952 001 106 1
2 ¾"/square 80 mm/hex DAF/Volvo 1952 001 312 1
3 ¾"/square 95 mm/hex Volvo 1952 001 309 1
¾"/square 105 mm/hex Volvo 1952 001 310 1
4 ¾"/square 95 mm/octagon Scania 1952 001 311 1
5 ¾"/square 100 mm/octagon Scania 1952 001 307 1
6 ¾"/square 115 mm/octagon DAF/Volvo 1952 001 308 1
1
1
2
3 4 5 6
2 3 Without guide band
230.85
151.27
443.65 469.06
(309)
(310)
291.11 240.26 251.69
8 SPECIAL TOOLS
Suitable for: IVECO EUROCARGO
Art. no. 1952 001 108PU/Qty. 1
Suitable for: IVECO Eurotech - Cursor, Stralis rear axle
Art. no. 1952 001 089PU/Qty. 1
Heavy-duty version for removal/mounting of dust caps and axle nuts.
AXLE NUT SOCKET CV ¾" DRIVE, 95 MM HEX
AXLE NUT SOCKET WITH GUIDE BANDFOR USE WITH 36 MM HEX SOCKET, 110 MM BIHEX
AXLE NUT SOCKET¾" DRIVE, 205 MM, OCTAGON
Size Suitable for Art. No. PU Price60 mm Any type of truck/commercial vehicle 1952 001 095 1 119.0065 mm 1952 001 096 1 129.4070 mm 1952 001 097 1 105.7580 mm Scania axle nut 124 L/144 L VA 1952 001 098 1 168.8285 mm Any type of truck/commercial vehicle 1952 001 099 1 199.3190 mm 1952 001 100 1 225.2595 mm 1952 001 101 1 243.31100 mm 1952 001 102 1 266.69105 mm 1952 001 103 1 277.61110 mm 1952 001 104 1 320.08115 mm VA Volvo FH 12 and FH 16 models from 1993 1952 001 105 1 355.43
CHASSIS
216.59
529.31
9SPECIAL TOOLS
AXLE NUT SOCKET FOR USE WITH 46 MM HEX SOCKET, 140 MM HEX
CHASSIS
GROOVE LOCK NUT SOCKET ¾" DRIVE
BEARING SHELL ASSEMBLY KIT
Stud width
No. of studs
Inner ∅ Suitable for Art. No. PU Price
7.5 mm 4 52/60 mm MB M Class; front and rear axle 1952 001 111 1 183.557.5 mm 6 62.8/ MB Actros, Atego (heavy-duty design) 1952 001 112 1 480.498.0 mm 6 92.5/ MAN-TGA front axle, V9-82L-01 (disc 1952 001 113* 1 270.77
Impact design for rotation-angle-monitored tightening, 32 mm drive for pre-tightening.
Suitable for: SAF axles, 9t RSM 9042, SKRS/RZ 9042, 11242, 9037, 11038
Art. no. 1952 001 088PU/Qty. 1
For the exact and centered removal and mounting of bearing shells, especially for mounting tapered roller bearings in wheel hubs without jamming them.
The specially shaped jaws are spread by an adjustment bolt for optimal placing. This allows for damage-free mounting without jamming. Robust forged design, can be disassembled easily. Also suitable for use in the workshop press. Working range Ø 85 – 180 mm.
Suitable for: Passenger cars, vans, commercial vehicles, buses, agricultural and construction machin-ery, mechanical and plant engineering
Art. no. 1952 001 280PU/Qty. 1
* with additional 60 mm hex
233.51
378.81
10 SPECIAL TOOLS
IMPACT SOCKET ¾" DRIVE, 27 MM BIHEX
DEEP IMPACT SOCKET ¾" DRIVE, E24, 110 MM
CHASSIS
• Length 112 mm• Burnished for spring U bolt connections
Suitable for: MB - trucks, Actros with air suspension, agricultural machinery
Art. no. 1952 001 214PU/Qty. 1
Heavy-duty version for works on axles and brakes.
Suitable for: Universal
Art. no. 1952 001 199PU/Qty. 1
IMPACT SCREWDRIVER BIT ¾" DRIVE, 17 MM HEX
For removal and mounting of the retaining screw of the upper control arm of the rear axle.
• Length 170 mm• For hex socket screws
Suitable for: MAN TGA and F2000, Citaro, MB Actros
Art. no. 1952 001 200 PU/Qty. 1
71.18
67.50
40.68
11SPECIAL TOOLS
GROOVE LOCK NUT SOCKET SET MAN TGA
GUIDE TUBE
ASSEMBLY SLEEVE
CHASSIS
For rear axles, with guide tube and base body
• Drive ¾", 60 mm hex• With 6 inner studs 11.5 mm• Dimensions inner stud - inner stud: 111.8 mm• Dimensions inner edge- inner edge: 132.0 mm• Total length: 111.0 mm
Suitable for: MAN-TGA rear axle, e.g., HY 1350
Base bodyArt. no. 1952 001 114PU/Qty. 1
Guide tubeArt. no. 1952 001 115PU/Qty. 1
For TGA rear axle groove lock nut socket/base body art. no. 1952 001 114.
• Ø 66.50 - 60.00 mm, length 140 mm
Suitable for: MAN-TGA rear axle
Art. no. 1952 001 115PU/Qty. 1
For MB/MAN rear axles.
• Outer Ø 76 mm• With internal thread M 75 x 1.5• Length 185 mm
Suitable for: Rear axle HL2 in MAN L series and MB Atego and Vario
Art. no. 1952 001 117PU/Qty. 1
£52.99
£50.99
£30.99
607.61
169.81
329.99
12 SPECIAL TOOLS
CHASSIS
EXTENSION TUBE FOR REAR AXLE
For TGA axles
• Length 360 mm, knurled• Outer Ø 105 mm• With internal thread to guide the bearing for mounting on the rear axle• Thread size M 100 x 1.5 mm
Suitable for: MAN rear axle HY 1350
Art. no. 1952 001 116PU/Qty. 1
Further groove nuts sets, base bodies and guide tubes available for the following makes: Mercedes hypoid rear axle, HL2/2, HL2/3, HL2/5, HL2/9, HL2/11, HL2/12, HL2/15, MB hypoid rear axle HL 2/14, KL2/16, KL4/1, HL4/16, HL4/17, HL4/23, HL4/28-HL4/30, HL4/4, HL4/8, HD4/6G, HO4/2, HO4/1, HO4/18 Nr. 4/4, MB hypoid axle HO 4/10, HO 4/10DL, HO 4/11DL, HO 5/3, HO 5/4, HO 5/8, HD 4/21G, HD 4/2G, HD 4/22, HD 5/3, HL 5/2, HL 5/6, MB hypoid axle HO 5/5, HL 4/01, HL4/05, HL4/06, HD4/02, HD4/03, MB palloid front axle AL 3/6, AL 3/9, MB trailing rocker shaft axles NS4/2, NS4/10, and for pinion axles HL6/1, HL6/2, HL6/3, HD6/3, MAN - VW 8.138, 8.150, 9.136, L2000, MAN hypoid (banjo-type) rear axles of the G series VW2, VW4, VW6.1, VW 6.8, MB hypoid rear axle HL2/2, HL2/7,HL2/13, MAN front axle (front drive) M series - 3 ME DI and planetary hub reduction rear axle 5 MR, 3 MR
GROOVE LOCK NUT SET REAR AXLE – COMMERCIAL VEHICLES ¾" DRIVE
With exchangeable guide tube for removal and mounting works on the rear axle.
• Studs: 6, Stud width: 10.0 mm• Inner Ø base body: 87.0 mm• Length 65 mm
Art. no. 1952 001 145 PU/Qty. 1
Suitable accessories:
Description Type Art. No. PU PriceBase body of groove lock nut socket w/o guide tubes MAN, MB Atego rear axle
(pinion shafts) HL2, 814 Vitaro
1952 001 146 1 217.39Guide tube outer Ø 49 mm, length 140 mm 1952 001 147 1 69.22Guide tube outer Ø 57 mm, length 140 mm 1952 001 148 1 45.76
424.06
331.78
13SPECIAL TOOLS
CHASSIS
GROOVE LOCK NUT SET REAR AXLE – COMMERCIAL VEHICLES ¾" DRIVE
GROOVE LOCK NUT SET – COMMERCIAL VEHICLES ¾" DRIVE
GROOVE LOCK NUT SET FRONT AXLE/REAR AXLE – COMMERCIAL VEHICLES¾" DRIVE
With exchangeable guide tube for removal and mounting works on the front and rear axle.
• Studs: 12, Stud width: 11.4 mm• Inner Ø base body: 101.5 mm
With exchangeable guide tube for removal and mounting works on the front and rear axle.
• Studs: 6, Stud width: 9.8 mm• Inner Ø base body: 117 mm
With exchangeable guide tube for removal and mounting works on the front and rear axle.
• Studs: 6, Stud width: 11.4 mm• Inner Ø base body: 101.5 mm• Length 140 mm
Art. no.1952 001 141PU/Qty. 1
Suitable accessories:
Suitable accessories:
Suitable accessories:
Description Type Art. No. PU PriceBase body of socket "without" guide tubes MAN planetary hub
reduction rear axle F series H7, HD7 and
1952 001 142 1 236.93Guide tube outer Ø 51.5 mm, length 135 mm 1952 001 143 1 69.22Guide tube outer Ø 66.5 mm, length 135 mm Hypoid rear axles F
series HY-1175, HDY-1175, HY-13110,
1952 001 144 1 69.22
Description Type Art. No. PU Price
Base body of socket "without" guide tubes MB Actros rear axle, HL, HL 8 (hypoid axle)
1952 001 149 1 244.06Guide tube outer Ø 60 mm, length 185 mm 1952 001 150 1 69.22
Description Type Art. No. PU PriceBase body groove lock nut socket "without" guide tube MB planetary hub reduction 1952 001 130 1 253.21Guide tube outer Ø 50 mm, length 135 mm MB planetary hub reduc-
tion rear axle (European axles) 10t and 13t, HL7/0, HL7/1, HL7/2, HL7/3, HL7/18, HO7/8, HO7/9, HL7/015, HL7/021, HD7/2, HD7/19DG, HD7/016DG, MB hub re-
1952 001 131 1 69.22Guide tube outer Ø 51 mm, length 85 mm 1952 001 132 1 69.22Guide tube outer Ø 53 mm, length 135 mm 1952 001 133 1 63.28
312.97
14 SPECIAL TOOLS
TIE ROD WRENCH SET ½" DRIVE WITH ADDITIONAL 30 MM HEX
Self-clamping adapters for the safe and damage-free removal and mounting of almost all types of tie rods also in enclosed spaces.
Scope of delivery: Tool mount with ½" square socket and 30 mm hex head, length 435 mm; two interchangeable adapters Ø 32 – 37 mm and 37 – 42 mm
Suitable for: Passenger cars/vans
Art. no. 1952 001 025PU/Qty. 1
Please refer to the manufacturer's specifications on how to use with torque wrench.
CHASSIS
CLAMP NUT WRENCH ½" + ¾" DRIVE
For clamp nuts on steering knuckles.
Size Type Suitable for Art. No. PU Price32 x 36 1 Light trucks – MB, 200 and 300 series 1952 001 167 1 76.2641 x 50 2 MB commercial vehicle axles: VL /7-8, VL 1/3, 5, 6, 7, VL 1/4, from 1979, VL /8, 9, 10, VL
2/5, 6, 7, 8, 9, VL 2/10, 1013 S-K, 1017 S-K, e.g., Atego1952 001 168 1 79.10
46 x 52 3 MAN/VW – G series, axle V7-26l-36L, types 8.136 and 8.150 1952 001 169 1 90.4050 x 62 4 MB commercial vehicle axles: VL 2/11 in type 814
(new lightweight series)1952 001 170 1 96.04
54 x 68 5 Mercedes SETRA bus S 215 HDH from 1990, NEOPLAN bus from 1990 1952 001 171 1 91.5356 x 71¾" drive
6 DAF, Kässbohrer Setra, MAN, MB axles: VL 3/8, 13, VO 3/10, VL 4/7, 9, 10 VD 4/14, VO 4/11, 13, 18, VL 4/15, 16, 19, VD 4/20 MB series: 36, 385, 387, 389, 391, 393, 395, 617, 620, 621, 622, 623, 625, 649, VO 3/10, 4/11, 13, 19 omnibus, 0303, 0305-G, 0305, Kässbohrer Setra: front axle 6.5t + 7.5t – S210-215 series, SG 215-219, trailing axle S216 HDS, S228 DT
1952 001 172 1 114.41
60 x 76¾" drive
7 MAN and MB, reinforced 9t front axle VL5, MB SK front axle VL 5/1 D-9, VL 5/2 D-9, 2629 series/6x4, 2635 K/6x4, 3535 K8/x4/4, e.g., Actros with disc brakes, as well as FAUST front axle
1952 001 173 1 137.29
342.72
15SPECIAL TOOLS
UNIVERSAL AXLE AND GROOVE NUT WRENCHHEAVY-DUTY DESIGN
For the removal and mounting of axle nuts or grease caps, e.g., on truck or trailer wheel hubs. Suitable for octagon or hex nuts, groove nuts, face nuts, round nuts with drilled holes, capstan nuts, etc. Wrench with ¾" drive.
• Clamping range hex: 70 - 150 mm• Clamping range groove nut: 80 - 170 mm• Tightening torques of up to 700Nm possible.
Scope of delivery: 1x axle and groove nut wrench, 2x adapters, round, 6 mm, 2x adapters, round, 8 mm, 2x adapters, round, 10 mm, 2x adapters, square, 6 mm, 2x adapters, square, 8 mm,2x adapters, square, 10 mm, 1x tension chain, 1x pin key Tools delivered in plastic foam insert
Art. no. 1952 001 281PU/Qty. 1
CHASSIS
INSERTION TOOL
Description Type Art. No. PU Dimensions Fig.Design 1 Shaft seal insertion tool for cassette seal A 021 997 69 47
MB Actros front axle 739.5 - rear axle 749.108/30MB front axle + tag axle ABS
1952 001 282
227.56
1
Design 2Shaft seal insertion tool for sealing rings in the wheel hub
Planetary hub reduction rear axle MB truck HL 7/1, HL 7/3, HL 7/18, HL 7/07, HL 7/015, HL 7/021, HD 7/2, HD 7/19DG, HD 7/01DG, HO 7/8Series: 1219, 1413, 1417, 1419, 1424, 1617, 1619, 1621, 1624, 1926, 2219, 2226, 2626, 2632
1952 001 283
226.26
1
Design 3Shaft seal insertion tool for planetary hub reduction axles equipped with ABS and simple shaft seal in tone ring
For MB, MAN, DAF and other 1952 001 284
265.68
1
Design 4Insertion tool for tone ring without shaft seal on MB Actros
MB Actros front axle with ABS and disc brakes, e.g., axle no. 739 520For tone rings without shaft seal!
1952 001 285
278.39
1
633.04
16 SPECIAL TOOLS
PNEUMATIC HYDRAULIC PUMP WITH QUICK-RELEASE COUPLING ¼" NPT
HYDRAULIC CYLINDER SET 32T
CHASSIS
• Pressure 700 bar• 1 liter volume• 2.20 m pivoted hose
Suitable for: Hydraulic cylinder set 16t, 22t, 32t
Art. no. 1952 001 255PU/Qty. 1
For pushing and pulling, with an operating range of approx. 113 mm.
• The special design allows for hitting the tie rod inserted into the pistonrod while pressing to increase the loosening torque, e.g., for corrodedor glued components
• Spindle for pulling and pressing are integrated into the piston rod• A compact hydraulic unit of low weight (8.5kg)• Universal tool kit for pressing out and pulling in steering knuckle bolts,
joint bolts and silent blocks.
Accessories included in delivery: Thread protection ring, pressure spindle M24 x 3, tie rod M22 x 2.5, nut M22 x 2.5
Suitable for: Commercial vehicles, buses, agricultural machinery, plant engineering, mechanical engineering
Art. no. 1952 001 257PU/Qty. 1
Using the pump allows for the hydraulic tools to be operat-ed by a single person. With matching quick-release coupling and return stop. 1,182.19
1,344.89
17SPECIAL TOOLS
UNIVERSAL TOOL KIT
CHASSIS
For pressing out and inserting steering knuckle bolts, joint bolts and silent blocks.
This kit contains all press sleeves and pieces required for works on steering knuckle bolts, joint bolts and silent blocks (also tapered types) and is suitable for most vehicles and agricultural machin-ery available on the market. Delivery does not include pneumatic hydraulic pump, art. no. 1952 001 255 nor hydraulic cylinder set 32t, art. no. 1952 001 257!
• Inside frame height 500 mm• Clamping range 130, 210, 295 mm• Push rods 140 x Ø 31 mm, 250 x Ø 31 mm• Press piece, impact adapter, step plate to mount
the pressure pipes
Suitable for: Any type of commercial vehicle, buses, agricultural machinery, construction ma-chines, plant engineering, mechanical engineering
Tool kit without case Art. no. 1952 001 258PU/Qty. 1
Tool kit including sturdy plastic case Art. no. 1952 001 262PU/Qty. 1
Pressure pipesLength Inside Ø Outside/offset Ø42 mm 47.80 mm 65 mm
145 mm 47.80 mm 65 mm
42 mm 65.80 mm 80/90 mm
130 mm 66.50 mm 80/90 mm
Sample application of hydraulic cylinder set 32t on steering knuckle bolts, joint bolts and silent blocks
3,200.78
3,455.01
18 SPECIAL TOOLS
UNIVERSAL SILENT BLOCK SET 36- OR 44-PIECE
CHASSIS
Tool kit for pulling out and in, e.g., silent blocks, anti-vibration mountings, bushes, ball bearings, shaft seals.
• Due to the different diameters of the pressure sleeves and matchingadapters, the tool can be easily adjusted to different diameters.
• If required, the different sleeves can also be reshaped individually.The spindles included allow for mechanical use of the tool kit. Guideadapter and bearing ensure a safe and smooth operation.
• In many cases the support and pressure sleeves can also be used to-gether with the 22t hydraulic cylinder, art. no. 1952 001 256, and thepneumatic hydraulic pump, art. no. 1952 001 255.
• In combination with the workshop press, only the pressure sleeves andadapters are used.
• Delivery in high-quality blow-molded case.
Suitable for: Passenger cars, commercial vehicles, buses, agricultural and construction machinery, also suitable for SUV/off-road vehicles, e.g., BMW X3, X5, X6, MB M series, Porsche Cayenne, VW Touareg
44-pieceInside Ø 74 – 112 mm
Art. no. 1952 001 260 PU/Qty. 1
36-pieceInside Ø 34 – 72 mm
Art. no. 1952 001 286PU/Qty. 1
Hydraulic cylinder set 22t For pushing and pulling, with an operating range of 70 mm
Art. no. 1952 001 256PU/Qty. 1
Operation with workshop press
Hydraulic operation with spindle
Mechanical operation with spindle
760.16
1878.77 1116.07
19SPECIAL TOOLS
Sample application with spindle and open bell
UNIVERSAL COMPACT WHEEL BEARING MOUNTING TOOL
Suitable for all vehicle types. For the quick, precise and damage-free mounting of compact wheel bearings. Due to its shape, the universal mounting tool can be used mechanically with a spindle, with any common hydraulic cylinder and with an arbor press. With the adjustable jaws, the tool can be quickly mounted on any compact wheel bearing diameter.
Type: Can be used universally for passenger cars such as VW, Audi, Seat, Skoda, Ford, Mazda, Porsche, Volvo etc. For compact wheel bearings with a diameter of the outer bearing ring of Ø 50 mm to Ø 80 mm max.Also suitable for VW T5, VW Touareg, Porsche Cayenne, VW Crafter and MB Sprinter from 2007.
Without hydraulic cylinder and spindleArt. no. 1952 001 302PU/Qty. 1
Polo 9N LupoVW T5 Sample application with spindle and hydraulic cylinder
Compact wheel bearing bell mounted
CHASSIS
760.16
20 SPECIAL TOOLS
IMPACT SCREWDRIVER BIT ¾" DRIVE, 14 MM HEX BIT, 170 MM
IMPACT SCREWDRIVER BIT ¾" DRIVE, XZN M16 X 80 MM
BRAKES
For hexagon socket screws. For the removal and installation of brake caliper screws on the rear axle.
Suitable for: MB Actros, Citaro with HL7 + HL8 axles Hypoid Neoplan ZF and TGA wheel hubs.
Art. no. 1952 001 201PU/Qty. 1
For the removal and installation of the rear brake caliper and flywheel screws.
Suitable for: VW Touareg, Mercedes Benz Atego flywheel
Art. no. 1952 001 039PU/Qty. 1
35.04
43.34
21SPECIAL TOOLS
DEEP IMPACT SOCKET ¾" DRIVE, E 22 X 110 MM
AIR FILTER CARTRIDGE WRENCH, THREE-LEGGED ½" DRIVE
DAF RING STRIKING WRENCH26 MM, LENGTH 160 MM
BRAKES
Designed for axles and brakes, heavy-duty version for highest demands.
Suitable for: Any type of commercial vehicle
Art. no. 1952 001 198 (size E24 on page 10)PU/Qty. 1
• For desiccant air drier cartridges of truck brakes• Adjusts from 80 – 150 mm• Milled, black oxide finish
Suitable for: Any type of commercial vehicle or agricultural machinery
Art. no. 1952 001 074PU/Qty. 1
For loosening the brake caliper when changing the brake discs.
Suitable for: DAF trucks XF95 and XF105
Art. no. 1952 001 195PU/Qty. 1
62.70
170.08
109.06
22 SPECIAL TOOLS
BRAKE DISC THICKNESS GAUGE, 0-50 MMSTAINLESS STEEL, MATT FINISH, CHROME-PLATED
BRAKE PISTON RETRACTOR SOCKET, STEEL VERSION12 MM HEX DRIVE WITH MAGNET
BRAKES
• Designed to measure the thickness of brake discs while still installed• Certified according to DIN 862• Hardened, with retaining screw
Suitable for: Vans, agricultural machinery
Art. no. 0715 76 16PU/Qty. 1
To reset (retract) the automatic brake piston adjustment when changing brake pads or making other repairs to the brake caliper.
Suitable for: SAF, KNORR brake calipers on commercial vehicles
BRAKE CALIPER WRENCH ¾" DRIVE, BIHEX, 340 MM
For the removal and installation of front caliper screws.
Size Art. no. PU Price8mm/square socket 1952 001 203 1 13.288mm/hex socket 1952 001 204 1 19.4810mm/hex socket 1952 001 205 1 22.4618 mm/triple square socket 1952 001 206 1 21.46
Size Suitable for Art. no. PU Price24 mm MB Atego and Actros 1952 001 196 1 84.1827 mm MB Atego and Actros,
Kässbohrer buses1952 001 197 1 87.28
87.48
23SPECIAL TOOLS
BRAKE CALIPER HEX SOCKET FOR MAN
• Special extra short version, 30 mm external hex drive with spring ball retention• Length 40 mm• For the removal and installation of brake caliper screws without removal of the steering knuckle arm
E20 for MAN TGM/Atego 9 t Art. no. 1952 001 287PU/Qty. 1
E24 for MAN TGM/Atego 12 tArt. no. 1952 001 288PU/Qty. 1
BRAKES
BRAKE SHOE SPRING PLIERSHARDENDED, 500 MM
• Heavy-duty version• For riveted and bonded brake shoes, for the
removal of drum shoe return springs
Suitable for: Any type of commercial vehicle or agricultural machinery
Art. no. 1952 001 202PU/Qty. 1
GREASE CAP PLIERS
For the simple and safe removal of axle grease caps.
• Maximum width 75 mm• Length 280 mm
Suitable for: Cars, vans, trailers and agricultural machinery
Art. no. 1952 001 289PU/Qty. 1
£62.99
74.88
56.36
22.30
23.86
24 SPECIAL TOOLS
BRAKE PISTON SPREADER
Size of spreader plates: Width 100 mm, height 60 mm, thickness 7.5 mm
Suitable for: Vans and light commercial vehicles
Art. no. 1952 001 208PU/Qty. 1
SELF-LOCKING PLIERS FOR POLYAMIDE BRAKE HOSES
BRAKE HOSE CUTTER FOR PLASTIC HOSES AND PROFILES
For the installation of polyamide brake hoses
Suitable for: Any type of commercial vehicle, Mercedes Benz*, trailers
• Max. diameter: 25 mm, 175 mm length
Suitable for: Any type of commercial vehicle
Art. no. 1952 001 241PU/Qty. 1
Ø Art. no. PU Price6-8-10-12-16 mm 1952 001 239* 1 156.656-9-12-14-16 mm 1952 001 240 1 158.6510-11-13-14 mm 1952 001 290 1 158.65
BRAKES
152.05
67.80
25SPECIAL TOOLS
ENGINE
CYLINDER HEAD WRENCH CV ¾" DRIVE, BIHEX, NOT OFFSET, IMPACT DESIGN
CYLINDER HEAD WRENCH CV ½" DRIVE, E 20, IMPACT DESIGN
For loosening and tightening cylinder head bolts of commercial vehicles.
Suitable for: Mercedes-Benz, MAN
For loosening and tightening cylinder head bolts.
Length: 132 mm
Suitable for: MAN models F2000/F90/F8 and buses with D25/D28 engines (MAN no. 80.99603.0255)
Art. no. 1952 001 031PU/Qty. 1
Size Length Art. no. PU Price17 mm 110 mm 1952 001 027 1 58.9019 mm 110 mm 1952 001 028 1 60.16
52.28
26 SPECIAL TOOLS
ENGINE
CYLINDER HEAD WRENCH CV ¾" DRIVE, 110 MM, NOT OFFSET, IMPACT DESIGN
GROOVE LOCK NUT SOCKET SET CV ½" DRIVE, 4-PIECE
GROOVE LOCK NUT SOCKET CV ½" DRIVE, WITH 4 STUDS, 70 MM
For loosening and tightening cylinder head bolts of commercial vehicles.
For tightening the pressure screw on the nozzle holder.
Suitable for: MAN, any type of Mercedes-Benz truck
Art. no. 1952 001 036PU/Qty. 1
For loosening and tightening the pressure screw on the nozzle holder.
• 8 mm wide• Inside/outside Ø: 22/29 mm
Suitable for: Commercial MAN and Mercedes-Benz vehicles: M 401/421, LA, A, M 403/423, M 470h
Art. no. 1952 001 032PU/Qty. 1
Size Suitable for Art. no. PU PriceE18 MAN model M 2000 and buses with
D08 engines 1952 001 029 1
58.9059.04E20 MAN models F8, F90, F2000 and
buses with D25/D28 engines, TGA1952 001 030 1
92.92
60.30
27SPECIAL TOOLS
ENGINE
GROOVE LOCK NUT SOCKET CV32 MM HEX DRIVE, WITH 4 STUDS, 8 MM
CV SOCKET ½" DRIVE, 19 MM HEX, 200 MM
TS SCREWDRIVER BIT SET (5-POINT STAR) 9-PIECE, ¼" DRIVE, WITH TAMPER-PROOF HOLE
For loosening and tightening the pressure screw on the nozzle holder.
For tensioning of the V-belt on the alternator.
Suitable for: MAN F90, F2000, Mercedes-Benz up to SK series
Art. no. 1952 001 037PU/Qty. 1
On socket rail in plastic case.
Suitable for: For instance, for unit pumps of Mercedes-Benz Atego, Actros and Rover immobilizer
Content: TS10/15/20/25/27/30/40/45/50
Art. no. 1952 001 038PU/Qty. 1
Length Properties Suitable for Art. no. PU Price125 mm With hole to lead through the connecting
cable for EDC enginesMAN engines and Mercedes-Benz Euro II engines of the 400 series
1952 001 034 1 53.5470 mm With 22 mm counter nut for a secure and
stable gripCommercial MAN and Mercedes-Benz vehicles: OM 401-404, 407, 409 h/ha, 421-424, 441-444/A/LA,
1952 001 035 1 65.52
46.62
25.72
28 SPECIAL TOOLS
ENGINE
CLUTCH CENTERING MANDREL SET 6-PIECE
INJECTOR LINE WRENCH, HEX ⅜" DRIVE, 70 MM, IMPACT DESIGN
INJECTOR LINE WRENCH, BIHEX½" DRIVE, 100 MM, IMPACT DESIGN
For the quick and precise centering of the clutch. For universal use on single- and dual-plate clutches.
Content: 1x each Mandrel, adjustable from Ø 36 – 45 mm and Ø 44 – 52 mm;Pilot bearing adapters Ø 20, 25, 27 and 30 mmSupplied in a plastic case.
Suitable for: Any type of commercial vehicle, buses, agricul-tural or construction machinery
Art. no. 1952 001 291PU/Qty. 1
90° for injection lines.
90° for injection lines.
Size Suitable for Art. no. PU Price10 mm Universal 1952 001 042 1
53.9612 mm 1952 001 043 1
14 mm 1952 001 044 1
16 mm 1952 001 045 1
17 mm 1952 001 046 1
18 mm 1952 001 047 1 58.7619 mm 1952 001 048 1 59.8822 mm 1952 001 049 1 63.58
Size Suitable for Art. no. PU Price14 mm Universal 1952 001 050 1 55.9416 mm 1952 001 051 1
17 mm 1952 001 052 1
18 mm 1952 001 053 1 58.1819 mm 1952 001 054 1
22 mm 1952 001 055 1 61.60
545.35
29SPECIAL TOOLS
ENGINE
CAMSHAFT ROTATOR
For the manual, precise adjustment of the engine by the recess in the ring gear.
MB and MAN ½" square drive with 2 gear wheelsSuitable for: Mercedes-Benz OM 401-404-407-409 h/hA, 421-424, 441-444/A/LA, 427, 429, 4289, 447/h/hA and all types of 12-cylinder MAN enginesArt. no. 1952 001 040 PU/Qty. 1
MB and MAN ½" square drive with 3 gear wheels and thick sandwich plateSuitable for: Mercedes-Benz 900 series, OM 904-906, e.g. Actros and Atego as well as all 5-, 6- and 8-cylinder MAN engines (no 12-cylinder engines), equivalent to MB 904589046300, MAN80-99626-6006Art. no. 1952 001 041PU/Qty. 1
DAF 24 mm hex driveSuitable for: F65, F75, F85, F95, CF 65, CF 75, CF 85, XF 95 Art. no. 1952 001 295PU/Qty. 1
Scania ½" square driveSuitable for: L series type 94/114/124/144 from 1996 – 2004 and R series from 2004Art. no. 1952 001 292 PU/Qty. 1
Volvo ½" square driveSuitable for: 6- and 12-liter engines, D9A, D12, D16C Art. no. 1952 001 293 PU/Qty. 1
DAF ½" square driveSuitable for: XF 105 Euro 5 Art. no. 1952 001 294PU/Qty. 1
126.61
164.99
70.32 97.46
240.26 240.26
30 SPECIAL TOOLS
ENGINE – TRANSMISSION
GEAR SWITCH IMPACT SOCKET ½" DRIVE, 27 MM OCTAGON, 75 MM
CV SOCKET ½" DRIVE, 27 MM OCTAGON, 60 MM
GEARBOX FLANGE SOCKET CV ½" DRIVE, 36 MM BIHEX, 77 MM
For instance, for electrical switches of transmissions and other applications.
Suitable for: Mercedes-Benz, MAN transmissions: 16S/112/130, 160/190, 710.4.5.7
Art. no. 1952 001 059PU/Qty. 1
For operating transmission and axle switches.
Suitable for: MAN, Mercedes-Benz Actros, SK series
Art. no. 1952 001 060PU/Qty. 1
Suitable for: Mercedes-Benz passenger car rear axle bearing W140/truck transmissions, MB transmission G2/24/26 coupling flange
Art. no. 1952 001 061PU/Qty. 1
44.90
37.28
54.52
31SPECIAL TOOLS
ENGINEENGINE – TRANSMISSION
OIL DIPSTICK SET4-PIECE
SEAL PULLER WITH TWO HOOK SHAPES
To measure the oil level of engines and automatic transmissions.
Suitable for: Mercedes Benz engine codes: M112, 113, 646, 647,648, 103, 104, 943, 984, 985, 111, 119, 120, 137, 603, 913, 963, 97, 604, 605, 606, 611, 612.965 and Mercedes Benz transmission codes: 716.5, 722.6, 722.7
Art. no. 1952 001 001PU/Qty. 1
Absolutely necessary after an oil change, as vehicles are now supplied by manufacturers without any oil dip-sticks and instead only feature a closing plug.
For the removal of sealing rings, O rings and shaft seals of any type.
• Length x width: 315 x 85 mm
Suitable for: Any type of passenger car or commercial vehicle, buses, agricultural and construction machinery, mechanical and plant engineering
Art. no. 1952 001 006PU/Qty. 1
152.15
18.64
32 SPECIAL TOOLS
ENGINEENGINE – FUEL INJECTION SYSTEM/FUEL
INJECTION PUMP SOCKET CV ½" DRIVE, 10 MM BIHEX, 110 MM
FUEL FILTER WRENCH ½" DRIVE, 95 MM 14PT
Ad-Blue® FILTER SOCKET ⅜" DRIVE, 45 MM HEX, 65 MM
For removal and mounting of the fuel injection pump.
Suitable for: Mercedes-Benz Actros
Art. no. 1952 001 057PU/Qty. 1
For removal and mounting of the fuel filter in accordance with the torque values specified by the manufacturer.
Suitable for: MAN-TGA, Mercedes-Benz Actros, agricultural machinery
Art. no. 1952 001 071PU/Qty. 1
For removal and mounting of the filter housing cap, for changing the filter element of Ad-Blue® filters in commercial Mercedes-Benz vehicles with Blue Tec® engine technology.Please observe the tightening torque of 23Nm recommend-ed by the manufacturer.
Suitable for: Mercedes-Benz new Actros, Atego, Axor, Econic
Art. no. 1952 001 296PU/Qty. 1
35.58
109.31
83.34
33SPECIAL TOOLS
ENGINEENGINE – RADIATOR
FILTER STRAP WRENCH FOR COMMERCIAL VEHICLES ½"
For removal and mounting of air and water filter cartridges.
Suitable for: Any type of commercial vehicle, construction and agricultural machinery
Clamping range Art. no. PUØ 105 – 118 mm 1952 001 072 1
Ø 130 – 143 mm 1952 001 073 1
COOLING SYSTEM TESTER SET FOR COMMERCIAL VEHICLES ALUMINUM VERSION, 9-PIECE
For leakage tests of cooling systems.
Scope of delivery: 1 Pressure pump with quick-release coupling, 1 flex-ible hose with quick-release coupling, 6 adaptersSupplied in a plastic case
Suitable for: Scania 113/114/124/125, DAF XF 95/XF 105, Mercedes-Benz Actros/Atego/Axor, Iveco Daily 2000-C series, MAN L 200-TGA, Volvo FH 12, MB Sprinter up to 2006
Art. no. 1952 001 064PU/Qty. 1
528.80
36.72
34 SPECIAL TOOLS
ENGINEENGINE – OIL SERVICE
EXTRA STRONG OIL FILTER CHAIN WRENCH ½" DRIVE
OIL FILTER STRAP WRENCH ½" DRIVE
OIL FILTER WRENCH ½" DRIVE
Suitable for: Universal
• Clamping range: 105 - 118 mm• Band width: 37.50 mm
Suitable for: Universal
Art. no. 1952 001 066PU/Qty. 1
For removal and mounting.
* Please observe maximum torque of 25Nm during installation
Chain links Ø Art. no. PU Price40 55 – 120 mm 1952 001 002 1 21.8848 60 – 135 mm 1952 001 067 1 25.9864 60 – 220 mm 1952 001 297 1 35.04
Size Suitable for Art. no. PU Price94 mm, 14pt MAN 403, 463 1952 001 068* 1 106.02106 mm, 15pt MAN 8 – 10t types:
L2000, LE, M2000, ME, also suitable for, e.g., MANN filter W 1160
1952 001 069 1 108.94
135 mm, 18pt MAN 18 – 48t types: TGA, F 2000, FE, 406 - 463, 404 - 464, also suitable for, e.g., MANN filter HU 1381x
1952 001 070 1 113.15
43.50
35SPECIAL TOOLS
ENGINEENGINE – OIL SERVICE/EXHAUST
OIL FILTER CAP SET 9-PIECE, 36 MM – 108 MM
OIL FILTER CAP WRENCH ⅜" DRIVE, 36 MM HEX
CHAIN PIPE CUTTERSPECIAL STEEL, NICKEL-PLATED
Scope of delivery: 1x each oil filter strap wrench, single-end box wrench size 22 mm, cap wrench size 36/hex, size 76/14pt., size 106/15pt., size 107/15pt., size 108/15pt. and size 108/18pt., all oil filter wrenches with hex head drive size 22 SW22 mm and ½" socket square drive
Suitable for: Universal
Art. no. 1952 001 003PU/Qty. 1
For removal and mounting of the oil filter housing cap when changing the oil filter cartridge.
Suitable for: Mercedes-Benz Actros MP1, MP2; 100D van engine 116 MB, E 250 D, M 605, M 606, E 300 D, E 220 D, C 220 D, C 250 D; MAN, e.g. TGA (fuel filter); BMW M5 2 – 6 cylinders, 3 series + 09/95, 5 series + 96, M6 0 – 8 cylinders, M7 3–12 cylinders, 8 series, 118 D, 120 D, 1 series (E87); VW Lupo 1.2 TDI, VW Touareg TDI, VW T5 2.5 D
Art. no. 1952 001 065PU/Qty. 1
• For copper, brass and thin-walled steel pipes, plastic-coated pipes andexhaust silencers
• Stainless steel pipes with up to 2.5 mm wall thickness and Ø 60 mm• Extra long chain allows for larger cutting diameter
Suitable for: Universal
Art. no. 0715 55 10PU/Qty. 1
Replacement chain:Art. no. 0715 55 101PU/Qty. 1
109.21
21.62
59.82 44.16
36 SPECIAL TOOLS
WHEELS/TIRES
FOUR-WAY CV LUG WRENCHHEXAGON
IMPACT SOCKET CV¾" DRIVE, 33 MM HEX, 90 MM LENGTH
For loosening and tightening wheel nuts of commercial vehicles.
• Welded and hardened version, painted• Heavy-duty version for professional use
Suitable for: Commercial vehicles, buses, construction and agricultural machinery
For loosening and tightening wheel nuts of commercial vehicles.
Suitable for: Any type of commercial vehicle, especially Scania
Art. no. 1952 001 220PU/Qty. 1
Drive Length Art. no. PU Price19 x 22 x 24 x 27 mm(¾ x ⅞ x ¹⁵⁄₁₆ x ¹·¹⁄₁₆")
550 mm 0715 16 02 1 43.3624 x 27 x 32 x 38 mm 750 mm 0715 16 04 1 101.6324 x 27 x 30 x 32 mm + ¹³⁄₁₆" 750 mm 0715 16 05 1 101.6327 x 30 x 32 x 33 mm 750 mm 1952 001 218 1 107.2827 x 30 x 32 x 33 mm(¹·¹⁄₁₆ x ¹·³⁄₁₆ x ¹·¹⁄₄ x ¹·⁵⁄₁₆" )
750 mm 1952 001 219* 1 161.44
* Robust, welded version, DIN 3119, fully hardened, chrome-plated, designed for heavy-duty applications.
30.78
37SPECIAL TOOLS
WHEELS/TIRES
WHEEL NUT SOCKET DEEP IMPACT HEXAGON SOCKET
CENTERING PIN SET ½"3-PIECE, 115 MM LENGTH
For loosening and tightening wheel nuts of commercial vehicles, buses, construction or agricultural machinery without extension.
Suitable for: Any type of commercial vehicle or truck
For the removal and mounting of centered drop-center wheels of commercial vehi-cles. No damage to the thread and exact centering of the rim due to tapered pins.
Size Drive Length Art. no. PU Price27 mm ¾" 270 mm 1952 001 221 1 107.2830 mm ¾" 270 mm 1952 001 222 1 107.2832 mm ¾" 270 mm 1952 001 223 1 114.4127 mm ¾" 400 mm 1952 001 224 1 129.1730 mm ¾" 400 mm 1952 001 225 1 129.1732 mm ¾" 400 mm 1952 001 226 1 133.2233 mm ¾" 400 mm 1952 001 227 1 133.2230 mm 1" 400 mm 1952 001 228 1 164.0032 mm 1" 400 mm 1952 001 229 1 164.0033 mm 1" 400 mm 1952 001 230 1 166.5434 mm 1" 400 mm 1952 001 231 1 166.54
Bolt hole Lug bolt Suitable for Art. no. PU Price21 mm M18 x 1.5 mm DAF, IVECO, MAN, RVI (Renault), Unimog, Volvo 1952 001 232 1
92.6624 mm 1952 001 233 1
26 mm M20 x 1.5 mm Scania 1952 001 234 1
M22 x 2.50 mm 1952 001 235 1
M22 x 1.5 mm DAF, Ford, MAN, Mercedes-Benz, Renault, Scania, Volvo 1952 001 236 1⁷⁄₈" – 11G Scania, Volvo 1952 001 237 1
⁷⁄₈" – 14G Volvo alloy rims 1952 001 238 1
38 SPECIAL TOOLS
BODY
SPECIAL BODY SEAM SPLITTER SET, EXTRA SLIM FOR LEFT- AND RIGHT-HAND USE – OFFSET
TS STAR SCREWDRIVER SET (5-POINT)WITH TAMPERP-ROOF HOLE, 8-PIECE SET
For the separation of body parts and spot-welded panels, especially back doors, side doors, etc.
• Concave side edge• Dimensions L x W x H: 290 x 25 x 7
Suitable for: Passenger cars, commercial vehicles, buses, agricul-tural machinery, mechanical and plant engineering
Art. no. 1952 001 004PU/Qty. 1
For TS five-point screws, 220 mm length, with ergonomic plastic handle For loosening and tightening security screws.
Content: TS 10, 15, 20, 25, 27, 30, 40, 45
Suitable for: Injection pumps, rear lights of MB Atego, Actros, MAN, Rover immobilizer system, Smart interior and exterior panels, Audi, VW and Fiat air flow meters
Art. no. 1952 001 298PU/Qty. 1
97.90
92.54
39SPECIAL TOOLS
BODY
MECHANIC TORQUE WRENCH ¾" DRIVE
• Precision setting, according to DIN EN ISO6789:2003
• Easy and accurate settings due to turnablehandle, robust steel version
• Reversible square drive for left- and right-handoperation
• Reaching the desired torque is indicated byan acoustic and palpable click, preventing ad-ditional tightening
• After use, relax spring and set to lowest torquevalue
• With calibration certificate, Quality "Made inGermany"
1
Fig. Drive Measuring range Scale div. Length Weight Head Ø Art. no. PUNm lbf. in. Nm mm g mm
1 ¾" 160 – 800 120 – 600 40 1,010 4,700 65 1952 001 305 1
824.99
40 SPECIAL TOOLS
BODY
PROFESSIONAL HAND RIVET TOOL
For aluminum and steel rivets as well as threaded rivets. Foldable handles, supplied with plastic case, incl. accessories.
• Aluminum/steel: 3.2; 4.0; 4.8; 5.0; 6.4 mm/M4; M5; M6; M8; M10
Suitable for: Any type of passenger vehicle, commercial vehicle, metalworking applica-tions, installations, construction, maintenance workshops, fittings
Art. no. 1952 001 242PU/Qty. 1
WIPER ARM PULLER WITH SPECIAL HOOKS AND LOCKING FEATURE
IMPACT SOCKET ½" DRIVE, 25 MM BIHEX, 45 MM LENGTH
• Max. opening/clearance: 0 – 60 mm/up to 50 mm
Suitable for: Passenger vehicles, vans, buses, construction and agricultural machinery
Art. no. 1952 001 008PU/Qty. 1
For the attachment of metal bumpers
Suitable for: Any type of commercial vehicle, especially MAN trucks
Art. no. 1952 001 215PU/Qty. 1
Perfect wiper arm removal due to integrated locking feature. The locking bolt securely fas-tens the hooks to the wiper arm ensuring safe removal of the wiper arm.
123.82
15.54
167.53
41SPECIAL TOOLS
BODY
PRY BAR SET4-PIECE
Suitable for: Any type of passenger vehicle, commercial vehicle, metal-working applications, installations, construction, maintenance workshops
Suitable for: Any type of passenger vehicle, commercial vehicle, metal-working applications, installations, construction, maintenance workshops
Art. no. 1952 001 299PU/Qty. 1
Available in four different versions:Straight, 930 mm lengthStraight, 30° offset and extra-wide blade, 920 mm lengthStraight, 60° offset, 650 mm lengthStraight, 90° offset, 640 mm length
Suitable for: Any type of passenger vehicle or commercial vehicle, metal-working applications, installations, construction, maintenance workshops
Art. no. 1952 001 250PU/Qty. 1
TAPER PIN PUNCH, US ALLOY STEEL, EXTRA LONG HEXAGON SHAFT AND TAPERED TIP
PARALLEL PIN PUNCH SET, 5-PIECE US ALLOY STEEL 3, 4, 5, 6, 8, EXTRA LONG TIPS, 110 MM
Ø Length Art. no. PU Price6.5 - 16 mm 280 mm 1952 001 247 1 33.608.0 - 19 mm 460 mm 1952 001 248 1 50.30
244.06
107.91
42 SPECIAL TOOLS
UNIVERSAL
IMPACT BIT SET 16-PIECE, ¾" AND 1" DRIVE
Bits made from chrome molybdenum steel, black oxide finish.
Contains: 13 bits with 22mm hexagon drive, Torx T60/T70/T80/T90/100, 17/19/22/24 mm hex bits, external Torx E18/E20/E22/E24, 2 bit holders with ¾" and 1" drive, 1 hex key to fasten the bits. Suitable for air impact drivers.
Art. no. 1952 001 015PU/Qty. 1
IMPACT BIT SET CV 10-PIECE, ¾" DRIVE
Suitable for: universal applications
Contains: one bit each for 14mm, 17mm, 19mm, 22mm and 24mm hexagon socket screws; for Torx screws T70, T80, T90 and T100 plus ¾" bit holder
Art. no. 1952 001 058PU/Qty. 1 233.39
266.56
43SPECIAL TOOLS
UNIVERSAL
STANDARD DRUM KEY 320 MM
FLEXIBLE RATCHET EXTENSION DRIVE WITH REINFORCED HINGES
For all standard drum caps.
Suitable for: Any type of passenger vehicle or commercial vehicle, metal-working applications, installations, construction, company workshops, fittings, woodworking applications
Art. no. 1952 001 263PU/Qty. 1
To access hard-to-reach locations and still apply high torques!
Suitable for: Any type of passenger vehicle or commercial vehicle, metalworking applications, installations, construction, company workshops, fittings, woodworking applications
½" drive, 225 mm length, max. angle 90°, 351 NmArt. no. 1952 001 276 PU/Qty. 1
⅜" drive, 235 mm length, max. angle 180°, 178 NmArt. no. 1952 001 275 PU/Qty. 1
66.40
40.26 42.08
44 SPECIAL TOOLS
UNIVERSAL
SPECIAL SCREWDRIVER BIT SET CV 38-PIECE, ¼" + ½" DRIVE
IMPACT SCREWDRIVER BIT SET 9-PIECE, ½" DRIVE
Contains: 1 piece each ¼" drive:TS drive (five-point) TS10/15/20/25/27/30/40/45/50 x 30 mm½" drive:Ribe profile R7 x 240/R8 x 240/R9 x 100/R10 x 140 mmTorx drive T40/T45/T50/T55/T60/T70 x 140 mmXZN drive M9 x 100/M10 x 140/M12 x 140/M14 x 140 mmHex drive 7mm x 230/10 mm x 140/11 mm x 140/13 mm x 140/14 mm x 55/17 mm x 55/19 mm x 55/22 mm x 55/24 mm x 55 mmSpecial ½" bits:Tamper-proof XZN bit M16 x 55 mm, XZN bit M16 x 100, impact XZN bit M18 x 78 mm, Torx bits T80 x 100/T30 x 300 mm both tamper-proof, hex bit 5 x 160 mm with ball head
Art. no. 1952 001 026PU/Qty. 1
• With ball-retaining groove and hole• Suitable for impact wrenches, 78 mm length
TorxContains: 1 piece each Torx drive T20/T25/T30/T40/T45/T50/T55/T60/T70
For Torx screws Art. no. 1952 001 245PU/Qty. 1
HexContains: 1 piece each 4/5/6/8/10/12/14/17/19 mm
Art. no. 1952 001 244PU/Qty. 1
158.38
82.20
82.20
45SPECIAL TOOLS
UNIVERSAL
IMPACT SCREWDRIVER BIT SET CV 6-PIECE, ½" DRIVE
IMPACT SCREWDRIVER BIT ¾" DRIVE, 76 MM
IMPACT SCREWDRIVER BIT ¾" DRIVE, BLACK OXIDE FINISH, EXTRA LONG
• XZN drive M14/M16/M18• Black oxide finish• 43 and 75 mm lengths on socket rail
Art. no. 1952 001 016PU/Qty. 1
For hexagon socket screws.
• For highest demands• Applications include: axles and brakes• For use on hard-to-reach fasteners
Size Suitable for Art. no. PU Price12 mm Mercedes-Benz: e.g. brake pads/
brake discsAudi/Seat/Skoda/VW: e.g. drive train components
1952 001 174 1 33.60
14 mm Universal 1952 001 175 1 44.9017mm Mercedes-Benz: e.g. brake pads/
brake discsAudi/Seat/Skoda/VW: e.g. drive train components
1952 001 176 1 37.2819 mm 1952 001 177 1 39.00
Size Suitable for Art. no. PU PriceT 60 x 130 Various applications, especially
Mercedes-Benz Actros brake discs, brake calipers, pitman arms
1952 001 178 1 43.50T 70 x 130 1952 001 179 1 46.34
For Torx drives
120.90
46 SPECIAL TOOLS
UNIVERSAL
IMPACT SCREWDRIVER BIT ½" DRIVE, SOLID, DESIGNED FOR SPECIAL APPLICATIONS, TORX
IMPACT SCREWDRIVER BIT ¾" DRIVE, TORX
IMPACT SCREWDRIVER BIT CV ½" DRIVE, TORX
Suitable for: Any type of commercial vehicle, especially Mercedes-Benz and MAN
For fasteners on brake calipers/brake discs, differential housings/drive shafts and steering gears.
Suitable for: Any type of commercial vehicle, especially Mercedes-Benz and MAN
• Heavy-duty version with exchangeable bit• For the highest quality requirements
Suitable for: Any type of commercial vehicle or truck
Size Length Art. no. PU PriceT30 55 mm 1952 001 181 1 18.92
100 mm 1952 001 182 1 26.84
Size Length Art. no. PU PriceT60 100 mm 1952 001 183 1 39.26
38.1439.5440.68
80 mm 1952 001 190 1
T70 80 mm 1952 001 191 1
T80 80 mm 1952 001 192 1
T90 80 mm 1952 001 193 1 44.90T100 80 mm 1952 001 194 1 52.54
Size Length Art. no. PU PRICET30 80 mm 1952 001 184 1
T40 80 mm 1952 001 185 1
T45 80 mm 1952 001 186 1
T50 80 mm 1952 001 187 1
T55 80 mm 1952 001 188 1
T60 80 mm 1952 001 189 1
32.5033.0633.0633.0633.0635.58
47SPECIAL TOOLS
UNIVERSAL
IMPACT SOCKET ¾" DRIVE, BIHEX, HEAVY-DUTY VERSION
EXTERNAL THREAD REPAIR SET NES123FOR EXTERNAL THREADS 4 – 152 MM + ⁵⁄₃₂" – 6"
Suitable for: Any type of commercial vehicle, especially Mercedes-Benz Atego
• Easy to adjust to any thread diameter and any thread pitch• No additional calibration necessary• Suitable for left- and right-hand threads• For metric and American thread standards with 60° thread angles• Delivered in blow-mold case
Suitable for: Various applications, passenger vehicles, commercial vehicles, metalworking applications, installations, construction, maintenance workshops
Contains:3 external thread repair tools: 1 NES1 4 – 18 mm + ⁵⁄₃₂" – ¹¹⁄₁₆"1 NES2 17 – 38 mm + ¹¹⁄₁₆" – 1 ½"1 NES3 35 – 152 mm + 1 ¼" – 6" 3 pairs of replacement blades and one manual deburring tool
Art. no. 1952 001 243PU/Qty. 1
Also available individually:
NES1, 4-18 mm + 5/32" - 11/16"Art. no. 1952 001 270
NES2, 17 – 38 mm + 11/16" - 1 ½"Art. no. 1952 001 271
NES3, 35 – 152 mm + 1 ¼" - 6"Art. no. 1952 001 272
Size Length Art. no. PU Price17 mm 50 mm 1952 001 209 1 28.8019 mm 50 mm 1952 001 210 1 28.8032 mm 53 mm 1952 001 211 1 33.0630 mm 100 mm 1952 001 212 1 48.8632 mm 100 mm 1952 001 213 1 54.52
126.61
190.40
419.22
836.42
48 SPECIAL TOOLS
UNIVERSAL
CIRCLIP PLIERS, MAXI
UNIVERSAL EXTENSION FORGED STEEL
• For internal and external circlips• Robust design, made of US spring steel• With ratchet mechanism and exchangeable, hardened, smoothed
and polished tips for greater durability• Contains: straight nose pliers
Suitable for: Any type of passenger vehicle or commercial vehicle, met-alworking applications, installations, construction, maintenance workshops
For the loosening of overtightened bolt connections in hard-to-reach places.
• Suitable for spanners, ring spanners, offset ring spanners, etc. also suitableas extension for hexagon keys such as inside hex, Torx, XZN or Ribe
• Integrated ½" square socket in the handle
Suitable for: Any type of passenger vehicle or commercial vehicle, metal-working applications, installations, construction, maintenance workshops
Total length: 340 mm for spanner sizes of up to 27 mmArt. no. 1952 001 261PU/Qty. 1
Total length: 580 mm for spanner sizes of up to 50 mmArt. no. 1952 001 300PU/Qty. 1
Version Ø Tipsmm
Lengthmm
Ø int./ext. circlip in mm
Art. no. PU Price
Internal 3.0 400 120 – 300 int. 1952 001 251 1 226.76External 3.0 400 120 – 300 ext. 1952 001 252 1 226.76Internal 3.8 730 250 – 400 int. 1952 001 253 1 324.92External 4.3 480 250 – 400 ext. 1952 001 254 1 324.92
80.78214.83
49SPECIAL TOOLS
UNIVERSAL
SQUARE SOCKET KEY 60 MM
• Made from malleable cast iron• Nickel-plated with oval handle
Suitable for: Mercedes-Benz and MAN buses
8 mm; length: 60 mmArt. no. 1952 001 301PU/Qty. 1
Suitable for: Truck storage cabinets
9 mm; length: 60 mmArt. no. 1952 001 264PU/Qty. 1
TRIANGLE SERVICES KEY 7 MM, ALUMINUM
For the removal of the upper housing of fuel truck connectors
Art. no. 1952 001 265PU/Qty. 1
STRIKING RING WRENCH
• Material: special steel• Standards: DIN 7444
Size Length Art. no. PU Price75 mm 330 mm 1952 000 703 1 217.6480 mm 360 mm 1952 000 704 1 319.4885 mm 360 mm 1952 000 705 1 384.3090 mm 390 mm 1952 000 706 1 467.1995 mm 390 mm 1952 000 707 1 519.37100 mm 420 mm 1952 000 702 1 593.77
9.02
8.18
3.96
50 SPECIAL TOOLS
UNIVERSAL
INSPECTION CAMERA, BASIC 7-PIECE, WITH 5.5 MM X 1 M SEMI-RIGID CAMERA CABLE
Quick and simple visual inspection of damage in hard-to-reach places without any expensive or time-consuming disassembly being required (e.g. rocker panels, engines, gearboxes, axles, cavities, cable ducts and many other applications).
• 4 powerful mini LEDs with brightness control• Portable, battery-powered system• Direct connection through AV socket and connecting cable• Camera head made of scratch-resistant sapphire glass to ensure maxi-
mum image quality and protect camera and lens• Additional mirror extensions to increase the field of vision• Digital zoom and mirror effect
Art. no. 0715 53 962PU/Qty. 1
ContainsDescription Art. no. PU PriceVideo camera head, 5.5 mm, semi-rigid, 0° 0715 53 776 1 233.01Mirror attachment 70° x 5.5 mm 0715 53 973 1 65.84Mirror attachment 90° x 5.5 mm 0715 53 974 1 65.84Mirror attachment 110° x 5.5 mm 0715 53 976 1 65.84Hook attachment 5.5 mm 0715 53 972 1 30.72Magnet attachment 5.5 mm 0715 53 971 1 35.10Hand-held device – 1
AV cable – 1
1.5 V AA alkaline battery 0827 112 4
Technical data2,4” TFT LCD QVGA color display Resolution: 320 x 240 pixels
Weight 1,704 grams/set
Video out format NTSC & PAL
Angle of view: Horizontal angle 46°
Vertical angle 34°
Diagonal angle 56°
Depth of field (DOF) At a distance of 1-6 cm
Camera head IP67-certified water-resistant
Suitable accessories:Description Art. no. PU PriceVideo camera head, 5.5 mm, flexible, 0° 0715 53 762 1 233.01Video camera head, 3.9 mm, semi-rigid, 0° 0715 53 775 1 584.93
392.27
51SPECIAL TOOLS
UNIVERSAL
INSPECTION CAMERA PRO 10-PIECE, WITH 5.5 MM X 1 M SEMI-RIGID CAMERA CABLE
For the inspection and documentation of hard-to-reach areas in the automo-tive, HVAC, construction, industry and aviation sector as well as for police and customs authorities with video recordings and/or photos as well as a live view through the TFT color screen and storage directly on the SD card.
• Recording function: Images in JPG and videos in NTSC or PAL format• Powerful battery: 2 hours charging for 4 hours continuous use• Optimum image quality due to 4 powerful mini LEDs with brightness
control• Portable, battery-powered system• USB connection• Direct connection through AV socket and connecting cable• Camera head made of scratch-resistant sapphire glass to ensure maxi-
mum image quality and protect camera and lens• Additional mirror extensions to increase the field of vision• Digital zoom and mirror effect
Art. no. 0715 53 761PU/Qty. 1
ContainsDescription Art. no. PU PriceVideo camera head, 5.5 mm, semi-rigid, 0° 0715 53 776 1 233.01Mirror attachment 70° x 5.5 mm 0715 53 973 1 46.99Mirror attachment 90 ° x 5.5 mm 0715 53 974 1 65.84Mirror attachment 110 ° x 5.5 mm 0715 53 976 1 65.84Hand-held device - 1
AV cable - 1
Charger: output 5.5 V, 1.8 A (10 Watt max.)
- 1
Input: 100–240 V/50–60 Hz/0.5 A
USB cable - 1
2 GB memory card - 1
Cleaning set - 1
Plastic case 535x300x85 mm - 1
Suitable accessories:Description Art. no. PU PriceHook attachment 5.5 mm 0715 53 972 1 30.72Magnet attachment 5.5 mm 0715 53 971 1 35.10Video camera head, 5.5 mm, flexible, 0°
0715 53 762 1 233.01Video camera head, 3.9 mm, semi-rigid, 0°
0715 53 775 1 548.93
Technical dataBattery Li-polymer 3.7 V (AC 100–240 V/50–60 Hz)
Display 3.5 TFT LCD QVGA
Image format JPEG (640 x 480)
Resolution H/V (325/250)
Operating temperature 0–55°C
Menu languages 26
Camera head 1 m x 5.5 mm semi-rigid, IP67 water-resistant
Angle of view: Horizontal angle 46°
Vertical angle 34°
Diagonal angle 56°
Mirror attachments 70°, 90°, 110° angle
Depth of field (DOF) At a distance of 1-6 cm
Weight 2250 grams/set
997.79
SPECIAL TOOLS
T: 00353 61 430200 www.wurth.ie
Würth Ireland LtdBallysimon Rd, Limerick,IrelandV94 AK71