specialty sensors - sor inc. · specialty sensors sorinc.com 913-888 ... el expansion loop hs heat...

Specialty Sensors

sorinc.com 913-888-2630

Table of Contents page

1500 & 1500R (B-1) ......................................................................................... 2

Pipe Clamp (1550) & Washer Thermocouple (1310) (B-2) ..................... 3

Tubeskin - 1510 & 1520 (B-3) ......................................................................... 4

Oil Seal - 1312 & 1314 (B-4) .......................................................................... 5

Heavy Duty Industrial Magnet - 1280 & 1290 (B-5) .................................. 6

Sensor, Thermowell & Transmitter Operations (B-6-8) .............................. 7

14685 West 105th Street, Lenexa, KS 66215 | 913-888-2630 | 800-676-6794 | sorinc.com | (03.14) ©SOR Inc.

Specialty Sensors - Surface

Electric Trace Sensor - Type 1500 and 1500R

TYPE 1500 - Used to accurately measure the surface temperature of any pipe or tank greater than 3 inches in diameter. The standard X and Y dimensions reduces the heat sinc effect and greatly improves the accuracy. The 1500 is widely used for electric heat tracing control for freeze protection and process control, especially where changes in temperature can cause process material to stratify.

Head Type Type Calibration X Junction Y Options

1500 or 1500R (see drawings for standard X and Y dimensions or indicate

To order: Indicate the code letter or value for each requirement.

HEad TYPE 0 No Head CA Cast Aluminum CI Cast Iron CSS Cast Stainless Steel LCA Large Cast Aluminum PP Polypropylene (Black) PPS Polypropylene Sanitary FTA Flip Top Aluminum FTP Flip Top Poly (white) EPA Explosion Proof Aluminum EPS Explosion Proof Stainless Steel EHA Explosion Proof Aluminum EHI Explosion Proof Iron

CalibRaTion J Iron Constantan® K Chromel® Alumel® T Copper Constantan® E Chromel® Constantan® N Nicrosil® Nisil® PO Low Temp RTD to 500° F PH High Temp RTD to 900° F PM Heavy Duty RTD to 900° FStandard RTD is a three-wire 100 ohm Platinum / .00385 Alpha. For higher temperature ranges - consult factory. For special limits on thermocouples, repeat calibration code, i.e. JJ.

SEnSoR JunCTion G Grounded U Ungrounded DG Dual Grounded DU Dual Ungrounded S Single RTD D Dual RTD FW Four Wire RTD

oPTionSS 3/4” - 2” (specify radius)M Radius for NPT pipe sizes 3” - 6”L Radius for NPT pipe sizes 6” and above

Type 1500

Type 1500R

Pad

2”

2”

Pad

TYPE 1500R - This surface temperature design allows easy removal of the sensor. In applications where there is heavy insulation on the pipe the sensor can be removed without disturbing or removing the insulation, reducing replacement downtime and costs.

Type1500

Type 1500R is available with

EHA and EHI heads only

X (4” Std.)

X (4” Std.)

Type RTD Type L Junction

(see drawings for standard X and Y dimensions or indicate desired dimension in inches)

To order replacement sensor for Type 1500R: Indicate the code/value for each requirement.

1500RS

B-1

Type1500

Type1500R

Type1500R

Type1500

11.50”

(L= x + y - 1/2”)

1/4” OD

3/8” OD

3” Radius

Y(3” standard)

Y(8” standard)

Sensor

Sensor

Type1500R

8.25” 2.00”1.25”

desired dimension in inches)

EPAA Explosion Proof Aluminum Atex

11.5



Washer Thermocouples - Type 1310

Type Calibration Washer Size Leadwire Length Options

J, K, T, E 6, 8, 10, 12, F - Fiberglass (inches) A - Armor 1/4, 3/8”, 1/2” P - PVC AP - Armor with T - Teflon® PVC Jacket SB - SS Over Braid

To order: To specify a washer thermocouple, indicate the code letter or value for each requirement.

Pipe Clamp - Type 1550

Washer thermocouples provide a simple but effective way to measure surface temperature on tanks and other welded metal structures. The thermocouple is imbedded in the washer for quick response and accurate location of the surface temperature.

Wire Gauge: 20 ga. solid (standard)

Type Head A Length Junction Pipe Size Calibration

Head TyPe0 No HeadCA Cast AluminumCI Cast IronCSS Cast Stainless Steel PPS Polypropylene SanitaryFTA Flip Top Aluminum

FTP EPA Explosion Proof AluminumEPAA EPS Explosion Proof Stainless SteelEHA Explosion Proof AluminumEHI Explosion Proof Iron

1550

(in Inches) (In Inches)

SenSor

Sensor JunctionG GroundedU UngroundedDG Dual GroundedDU Dual UngroundedFor special limits on thermocouples, repeat calibration code, i.e. JJ.

Sensor CalibrationJ Iron Constantan®K Chromel® Alumel®

A


Pipe Size

For heavy duty industrial surface temperatures use Type 1550. The black carbon steel nipple is welded to the black carbon steel pipe clamp adapter and the thermocouple is springloaded and maintains constant contact with the measuring surface. “A” length is normally determined by the insulation thickness surrounding the pipe. Sensor replacement requires no disassem-bling. For use with pipes 4 inches in diameter or larger.

B-2

1310

Flip Top Poly (white)

Explosion Proof Aluminum Atex

Lead Wire


Specialty Sensors - Surface Tubeskin Thermocouples - Type 1510

Head Type Sensor Type Calibration OD Junction Sheath Length Sheath Material Lead Length Lead Wire Pipe Size NPT Pad Mounting Options

(inches) (inches)


1510

Head Type0 No HeadCA Cast AluminumCI Cast IronCSS Cast Stainless SteelPPS Polypropylene SanitaryFTA Flip Top AluminumFTP Flip Top Poly (white)EPA Explosion Proof AluminumEPAA Explosion Proof Aluminum AtexEPS Explosion Proof Stainless SteelEHA Explosion Proof AluminumEHI Explosion Proof Iron

SenSor Sensor CalibrationJ Iron Constantan®K Chromel® Alumel®T Copper Constantan®E Chromel® Constantan®N Nicrosil® Nisil®For special limits on thermocouples, repeat calibration code, i.e. JJ.

Sensor od18 1/8”316 3/16”14 1/4”516 5/16”38 3/8”

Sensor Sheath MaterialsP 304SSR 316SSQ 310SSA Alloy 600Standard Sheath Material is 316SS.

Lead WireF FiberglassT Teflon®P PVC

pIpe MoUnTInGP ParallelW Wrap AroundBP Weld Bevel - ParallelBW Weld Bevel - Wrap AroundF Flat

opTIonSA Armor (Stainless Steel)AP Armor with PVC JacketBS Bell Spring Transition ReliefCG12 Weathertight Fitting 1/2” NPTCT Compensated Terminals (EHA/ EHI heads only)EL Expansion LoopHS Heat ShieldSB Stainless Steel OverbraidSS18 Adj SS Comp Fitting 1/8” NPT*SS14 Adj SS Comp Fitting 1/4” NPT*SS12 Adj SS Comp Fitting 1/2” NPT*ST Smooth Transition*Add T after SS for Teflon® Ferrule

Sensor JunctionG GroundedU UngroundedDG Dual GroundedDU Dual Ungrounded

Tubeskin Thermocouples - Type 1520

Head Type Sensor Type Extension A Length Calibration OD Junction Sheath Length Sheath Material Pipe Size NPT Pad Mounting Options

(inches) (below bushing) (inches)


1520

Head Type0 No HeadCA Cast AluminumCI Cast IronCSS Cast Stainless SteelPPS Polypropylene SanitaryFTA Flip Top AluminumFTP Flip Top Poly (white)EPA Explosion Proof AluminumEPAA Explosion Proof Aluminum AtexEPS Explosion Proof Stainless SteelEHA Explosion Proof AluminumEHI Explosion Proof Iron

Sensor Sheath MaterialsP 304SSR 316SSQ 310SSA Alloy 600Standard Sheath Material is 316SS.

SenSor Sensor CalibrationJ Iron Constantan®K Chromel® Alumel®T Copper Constantan®E Chromel® Constantan®N Nicrosil® Nisil®For special limits on thermocouples, repeat calibration code, i.e. JJ.

Sensor od18 1/8”316 3/16”14 1/4”516 5/16”38 3/8”

Sensor JunctionG GroundedU UngroundedDG Dual GroundedDU Dual Ungrounded

exTenSIonN Nipple GalvanizedNUN Nipple/Union/Nipple NS Nipple Stainless SteelNUNS Nipple/Union/Nipple PNUN Pressure Seal in Union PNUNS Pressure Seal in Union See page A-7 for additional information.

Note: For Tubeskins with Expansion Loops please provide sketch showing:1. A) Number of loops, B) Location, C) OD of loops

Heat ShieldOptional

Expansion Loop M.I.Cable

Furnace Wall

See Detail

DETAIL

Pressure Seal Supplied in Union

B-3

Optional Bushing Specify NPT

3/4” NPT

Note: For Tubeskins with Expansion Loops please provide sketch showing:1. A) Number of loops, B) Location, C) OD of loops

Wrap Around Mount

Weld Bevel Mount

Weld Pad

Field WeldThermocouple

Mounting Clamp

1” X 1”

(one per sensor)

Weld Pad

Leads

Expansion Loop

A

Lead Length

Sheath Length

pIpe MoUnTInGP ParallelW Wrap AroundBP Weld Bevel - Parallel

Galvanized

Stainless Steel

Galvanized

Stainless SteelBW Weld Bevel - Wrap Around F Flat

opTIonSBN Process Connection NPT (NPT SIZE) CT Compensated Terminals (EHA/EHI heads only) EL Expansion LoopHS Heat Shield

1.20” TransitionMax. Temp. 300°F (std.)

(See 1510 section for illustration)



Oil Seal - Type 1312 & 1314When a bearing is not properly lubricated, premature failure can occur. This failure can prove to be costly. This design has proven successful in measuring various types of bearing temperatures. The sensor provides quick response alerting the operator to an overheated condition. The O-ring prevents lubricants from contaminating components in the head and de-signed not to swell even when in continuous contact with oils and synthetic lubricants. This feature allows the spring to maintain positive pressure against the bearing housing and assures good temperature readings. This sensor is available with 316SS sheath and 3/16” OD. Cast aluminum head is standard. Maximum temperature 400°F, maximum pressure 50 psi.

Head Type Type Calibration OD Junction Length


Head Type0 No HeadCA Cast AluminumCI Cast IronCSS Cast Stainless SteelPPS Polypropylene SanitaryFTA Flip Top AluminumFTP Flip Top Poly (white)EPA Explosion Proof AluminumEPAA EPS Explosion Proof Stainless SteelEHA Explosion Proof AluminumEHI Explosion Proof Iron

SenSOr Type1312 1/2” NPT Process1314 1/4” NPT Process

Sensor CalibrationJ Iron Constantan®K Chromel® Alumel®T Copper Constantan®E Chromel® Constantan® N Nicrosil® Nisil® PO Low Temp RTD to 500° FPH High Temp RTD to 900° FPM Heavy Duty RTD to 900° FStandard RTD is a three-wire 100 ohm Platinum/.00385 Alpha. For higher temperature ranges - consult factory. For special limits on thermocouples, repeat calibration code, i.e. JJ.

316 = 3/16” Length in inches below fitting

316

Sensor JunctionG GroundedU UngroundedDG Dual GroundedDU Dual UngroundedS Single RTDD Dual RTD

B-4

Explosion Proof Aluminum Atex

Spring

1/2” NPT

O-Ring Seal

Type 1312 Type 1314

LL

Spring

1/4” NPT

O-Ring Seal

OpTIOnSFW Four WireGA Class ARTD Only

14685 West 105th Street, Lenexa, KS 66215 | 913-888-2630 | 800-676-6794 | sorinc.com | (03.14) ©SOR Inc.B-5

This rugged magnet thermocouple provides hands free surface measurement of tanks, bearing housings, pipes and air ducts. The 25-pound minimum pull magnet allows a strong attachment to rust free and clean surfaces and may be used for temperatures up to 950°F. A standard bell spring provides stress relief for all lead wire constructions. The optional handle allows proper positioning of the magnet to the measuring surface.

Sensor Type Calibration OD Junction Sheath Length Sheath Material Lead Length Lead Insulation Termination Options

(inches) (inches) 1280

SenSor

Sensor CalibrationJ Iron Constantan®K Chromel® Alumel®

Sensor oD18 1/8”316 3/16”14 1/4”

Sensor JunctionG U UngroundedDG Dual GroundedDU

Sensor Sheath MaterialR 316SS

LeAD InSULATIon

T Teflon® 20 ga. solidM T Multi Strand (flexible) Teflon® 20 ga.

Termination

1 Bare Ends2 Large Plug3 Miniature Plug8 Dual Large Plug11 Compensated Spade Lugs

optionsA Armor (Stainless Steel) AP Armor with PVC JacketHDL Handle

r

Dual Ungrounded

Grounded


Lead Length

SensorLength

Sensor OD

.375” OD

Spring

Magnet

Heavy Duty Industrial Magnet Thermcouple - Type 1280

Heavy Duty Industrial Magnet rTD - Type 1290

1.20” TransitionMax. Temp. 300°F (std.)

When the application requires a temporary RTD surface measurement or has a difficult mounting position - this assembly with a heavy duty magnet could be the solution. Sensor can be easily replaced without removing the magnet or holder and a variety of sensor options are available.


Sensor Type RTD Type OD Junction Sheath Length Sheath Material Lead Length Lead Insulation Termination Options

1290 r

2.250”

0.938”

2.00”

2.437”

Spring

U-ShapeMagnet

Pad

Spring HolderSensor

Lead Wire

14 2.25”

SenSor

Sensor TypePO Low Temp RTD to 500°FPH PM Heavy Duty RTD to 900°F

Sensor oD14 1/4”

Sensor JunctionS Single RTDD Dual RTD

Sensor Sheath MaterialR 316SS

(inches) (inches)

High Temp RTD to 900°F

LeAD InSULATIon

MF Multi Strand (flexible) Fiberglass 22 ga.MT Multi Strand (flexible) Teflon® 22 ga.

Termination1 Bare Ends11 Spade Lugs12 Large Three Pin Plug14 Mini Three Pin Plug

optionsA Armor (Stainless Steel) AP Armor with PVC JacketSB Stainless Steel Overbraid Leads


OC Oxygen CleanedRB Reduced Bore .230 to .130 for Bar Stock ThermowellsSC Stainless Steel Plug and ChainST Stellite® CoatingTF Teflon® CoatingTS Tantalum SheathVC Velocity CalculationsWB .385 Bore for Bar Stock ThermowellsSH Schedule 80 PipewellsSX Schedule 160 PipewellsSXX Double Extra Heavy PipewellsTC Tungsten Carbide

TRANSMITTER OPTIONSOrder DescriptionSymbol

HC Hart® CompatibleLCP Programmable, RTD, FMPT Programmable TypeTI Temperature Indicator (to be used with transmitter)

NOTE: If more than one option per sensor is needed place a dash (–)between each option ordered, i.e. –A–CG12 (armor with weathertight fitting)

MATERIAL LISTOrder DescriptionSymbol

AA Alloy 20A Alloy 600W Alloy 601I Alloy 800V Alloy 825Y BrassS Carbon Steel A105/A350SS Duplex Stainless SteelBB F11 1 ¼%Cr - 1/2%MoCC F22 2 ¼%Cr - 1%MoDD F5 5%Cr - 1/2%MoFF F9 9%Cr - 1%MoLL F91 9%Cr - 1%Mo - 0.2%VanaduimB Hastelloy® BC MM Hastelloy® XGG Haynes HR160HH Haynes 230JJ M Alloy 400 (Monel®)N Alloy 2200 (Nickel)T Teflon®P 304 Stainless SteelHP LP Q R 316 Stainless SteelHR LR D F H Z Other (specify)

B-6

SENSOR OPTIONSOrder DescriptionSymbolA Armor (Stainless Steel)AP Armor with PVC Jacket (Black)AT Armor with Teflon® Jacket (White)BA Bayonet Adapter (Adjustable) ADJ.BCA Bayonet Cap on ArmorBD45 45° Bend in Sheath (Note Inches From Bend to Tip)BD90 90° bend in Sheath (Note Inches From Bend To Tip)BF Bayonet Cap & Spring (1/8 & 3/16” OD Only) (Note Inches From Cap To Tip (Fixed))BR18 ADJ. Brass Compression Fitting 1/8” NPTBR14 ADJ. Brass Compression Fitting 1/4” NPTBR12 ADJ. Brass Compression Fitting 1/2” NPTBS Bell Spring Transition ReliefCG12 Weather Tight Fitting Leads Only 1/2” NPTCT Compensated Terminals (EHA/EHI head only)CV DE12 Double Ended Hex Fitting, ½” NPT Spring LoadedEL Expansion Loop Type 1510, 1520FW Four Wire Element RTDGA Class A Tolerance Per DIN EN 60751 RTDHA HS Heat Shield Type 1510, 1520HTP High Temperature Potting (Service over 400°F)HV High Vibration (PM RTDs only)L Pad Radius for NPT Pipe Sizes 6” and Above Type 1500LB Connector “L” Bracket For M.I. CableLJ Large Jack – J, K, T, E, R/S CU (When Purchased With Plug)M Pad Radius for NPT Pipe Sizes 3 - 6” Type 1500MJ Miniature Jack - J, K, T, E, R/S CU (When Purchased With Plug)NT No Transition (Sheath length is over all length)PMB Plastic Melt Bolts - Machined of Solid 304 S/S Bar 1/2-20 UNF Threads, Standard Lengths “L” 3, 4, 6, 8, 10 and 12SA Spring AssemblySA12 Spring Assembly with Hex Fitting 1/2” NPT 304SSSB Stainless Steel Overbraid on Lead WireSE12 Single Ended Fixed Hex Fitting 1/2” NPT 304SSSE14 Single Ended Fixed Hex Fitting 1/4” NPT 304SSSE18 Single Ended Fixed Hex Fitting 1/8” NPT 304SSSS18 ADJ. SS Compression Fitting 1/8” NPTSS14 ADJ. SS Compression Fitting 1/4” NPTSS12 ADJ. SS Compression Fitting 1/2” NPTST Smooth TransitionT Teflon® Ferrule for SS or BR Adjustable Fitting (i.e. SST12)TA Tube on Armor ¼” OD x 2” longTAC Tube on Armor with SS12 Fitting for Head MountTE Tinned Ends (Multistranded wire only)TF Teflon® Coated SheathTW Two Wire Element RTDVH Vent Hole in Compression FittingWC Wire Clamp Bracket For Leads (Page XX)WP Weld Pad 1” x 1” x 1/8” SS

THERMOWELL OPTIONSOrder DescriptionSymbol

BC Brass Plug and ChainDP Dye Penetration TestingFP Full Penetration WeldHTE Hydrostatic Pressure Test ExternalHTI Hydrostatic Pressure Test InternalNC NACE Certification

Connector with Epoxy Sealed Screws

High Accuracy RTD (Low Temperature only)

Hastelloy® C276

Haynes 556

304H Stainless Steel304L Stainless Steel310 Stainless Steel

316H Stainless Steel316L Stainless Steel321 Stainless Steel347 Stainless Steel446 Stainless Steel

Sensor, Thermowell and Transmitter Options



B-7

TA - Tube on Armor

A - Armor (Stainless Steel)

SB - Overbraid (Stainless Steel)

BS - Bell Spring Transition ReliefBF - Bayonet Cap and Spring

BCA - Bayonet Cap on ArmorBA - Bayonet Adapter

CG12 - Weather Tight Fitting

Single End Hex Fitting Stainless Steel

(SE12, SE14, SE18)

SA12 - Spring Assembly with Hex Fitting Stainless Steel

PMB - Plastic Melt Bolt

Thermowell Plug and Chain

LB - Connector “L” Bracket

HS - Heat Shieldfor Type 1510 and 1520

DE12 - Double Ended Hex Fitting, 1/2” NPT Spring Loaded

Stainless Steel

AP - Armor with PVC

EB - Reducer Bushing for Head Conduit 3/4” to

1/2” NPT

BPIX - Battery Powered Indicator Explosion Proof

BPI - Battery Powered LCD

ST - Smooth TransitionRed mark denotes start of

transition, do not install compressionfitting above red mark

SC = Stainless Steel

BC = Brass



B-8

Adjustable Compression Fitting(BR18, BR14, BR12, SS18, SS14,

SS12; shown is 1/2” NPT SS)

WP - Weld PadTAC - Tube on Armor with SS12 Fitting

NOTES:

specialty sensors - sor inc. · specialty sensors sorinc.com 913-888 ... el expansion loop hs heat...

Documents