spies hecker

Spies Hecker Technical Information.

Technical Data Sheets.

Jan 2007

Always look for the GREENTEC logo as it guarantees that the product is VOC compliant

The content of each individual Data Sheet must be

followed to ensure that the optimum result is achieved

All product and technical information references contained within this manual are correct at time of publication

For further equipment information please contact the

original supplier. Spies Hecker only recommends equipment and specifications in relation to use with their product range.

TECHNICAL DATA SHEETS 2.1 Paints and Topcoats

2.1.7 Permasolid® HS Clear Coat 8030 8030 / 10 / 99 UK

2.1.8 Permahyd® Base Coat Series 280 280 / 10 / 99 UK

2.1.9 Permahyd® Base Coat Series 285 285 / 10 / 99 UK

2.1.11 Permasolid® HS Automotive Topcoat Series 270 270 / 10 / 99 UK

2.1.12 Permacron® Elastic Clear Coat 8070 Satin Gloss 8070 / 10 / 99 UK

2.1.15 Permasolid® HS Clear Coat 8035 8035 / 01 / 02 UK

2.1.18 Permasolid® HS Optimum Clear Coat 8600 8600 / 02 / 04 UK

2.1.20 Permasolid® Diamond Clear Coat 8450 8450 / 08 / 05 UK

2.2 Primers and Surfacers

2.2.1 Priomat® 1K Primer Red Brown 7119 aerosol 7119 / 10 / 99 UK

2.2.2 Permasolid® HS Surfacer Plus 5110 Grey 5110 / 01/ 02 UK

2.2.7 Permahyd® lK Primer Surfacer 4l00 4100 / 10 / 99 UK

2.2.16 Permasolid® SpectroFlex 5400 5400 / 02 / 03 UK

2.2.17 Priomat® 1K Wash Primer 4085 4085 / 02 / 04 UK

2.2.18 Priomat® 1K Wash Primer 4085 aerosol 4085a / 02 / 04 UK

2.2.19 Priomat® Wash Primer 4075 4075 / 02 / 04 UK

2.2.20 Priomat® EP Primer Surfacer 4090 stone grey 4090 / 10 / 04 UK

2.2.21 Permasolid® HS Express Surfacer 5250 5250 / 05 / 06 UK

2.2.22 Permasolid® HS Wet on Wet Surfacer 5330 5330 / 08 / 06 UK

2.2.23 Permasolid® HS Vario Surfacer 8590 8590 / 12 / 06 UK

2.3 Bodyfillers

2.3.4 Raderal® IR Premium Putty 2035 2035 / 02 / 03 UK

2.4 Plastic Painting System Including Special Products

2.4.1 Priomat® Pore Filler 3311 3311 / 10 / 99 UK

2.4.8 Permacron® 1:1 Elastic Primer Surfacer 3300 Black 3300 / 10 / 99 UK

2.4.9 Permasolid® Elastic Additive 9050 9050 / 10 / 99 UK

2.4.10 Permasolid® Textured Additives SA 101 Coarse SA101 / 10 / 99 UK

2.4.11 Permasolid® Textured Additives SA 102 Fine SA102 / 10 / 99 UK

2.4.12 Permasolid® Matting Additive MA 100 MA100 / 10 / 99 UK

2.4.13 Permacron® Elastic Primer 3410 aerosol 3410 / 02 / 04 UK

2.6 Ancillaries Including Special Products

2.6.4 Permanent® Silicone Remover 7010 7010 / 10 / 99 UK

2.6.8 Permahyd® Precleaner 7080 7080 / 10 / 99 UK

2.6.9 Permacron® Blend-in additive 1035 1035 / 01 / 02 UK

2.6.11 Permahyd® Stone Chip Protector 7100-7103 7100-7103 / 07 / 06 UK

2.6.12 Permahyd® Blend-In Additive 9005 New 9005 / 11 / 06 UK

2.6.13 Permacron® Speed Blender 1036 1036 / 11/ 06 UK

USAGE OF PICTOGRAMS

Preparation

Cleaning

Underseal spray gun

Mixing Spray coats

Mixing ratio - 2 components

Application with spatula / spreader

Mixing ratio - 3 components

Application with brush

Use of measuring stick

Application with roller

Addition of hardener

Drying

Reduction of viscosity Flash-off

Application viscosity

Drying time

Water-thinnable

Drying with infrared

Application

Gravity feed spray gun

Suction feed spray gun

Further steps Close tin after use

Sanding by hand / dry

Miscellaneous

Sanding by hand / wet

Hand stirring

Orbital sander / wet (Compressed Air)

Stirring on the mixing machine

Orbital sander / dry

Flat bed sander / wet (Compressed Air)

Flat bed sander / dry

Polishing

Technical Information

See Technical Data Sheet

Storage

Store free from frost

Store in a cool place

Protect from humidity

2.1.7

Technical Data Sheet

Permasolid® HS Clear Coat 8030

Permasolid® HS Clear Coat 8030 is a high gloss, high solids clear coat from our acrylic range.

Thanks to its high solid content and excellent filling power, it can be applied efficiently in one application. HS Clear Coat 8030 is very economic in use and provides increased productivity through its greater surface coverage and shorter processing time. Its high resistance to the effects of weathering and environmental pollution ensure a durable protective paint film.

For professional use only! VR Technical Data Sheet No. 8030/10/99-UK

Substrate

Suitable base coats: Permahyd® Base Coat Series 280

Permahyd® Base Coat Series 285

Application

Mixing Ratio:

2:1 by volume with Permasolid® HS Hardener 3515 Slow 2:1 by volume with Permasolid® HS Hardener 3310 2:1 by volume with Permasolid® HS Hardener 3307 Extra Fast (for small areas up to 3 panels).

Pot Life: Approx. 90 minutes at 20 °C ready for use.

Method of application

Compliant HVLP

Application Viscosity 4mm , @ 20°C, DIN 53211:

22" DIN 4/20 ºC 22" DIN 4/20 ºC

Reducer at +20°C material temperature

Not required

Spray nozzle:* 1.3 to 1.4mm 1.3 to 1.4mm

Spray pressure:* For recommended spraying pressure refer to spraygun manufacturer

Atomising pressure 0.7 bar

No. of coats:

1 application: 1 grip coat followed by 1 full coat

Recommended film thickness

50 - 60 µm

Drying

Air drying:

at 20 °C ambient temperature

Dust free: 40-50 minutes

Dry for handling: 4-6 hours

Through dry overnight

Force Drying:

Flash-off time:

approx: 5 minutes

20 minutes at 60 °C metal temperature 3307 30 minutes at 60 °C metal temperature 3310/3315

Infrared drying:

Flash-off time:

approx: 5 minutes

Short wave 10 – 15 minutes

Medium wave 15 – 20 minutes

Technical Data

Viscosity as supplied: 65 - 75 seconds

Flash point: Clear Coat and hardener over 23 °C

Solids content: Base Material Mixed

approx. 58.9% by weight approx. 55.9% by weight approx. 53.4% by volume approx. 49.9% by volume

S.G. approx. 1.00g/cm3 approx. 1.00 g/cm3

Coverage* approx. 9.9 m2 /1 at 50 mm dry film thickness *The coverage has been calculated on the basis of the recommended dry film thickness an percentage solid content by volume (without reducer). In view of the variable application techniques the calculation is based upon 100% transfer efficiency.

VOC Content:* The EU limit for this product (2004/42/IIB(d)(420) 420) in ready for use form is max. 420g/litre of VOC. The VOC content of this product in ready to use form is max. 420g/litre

*VOC values determined in practice according to ISO 11890/2

Storage

All paint products must be stored in dry conditions within the temperature range 5 ºC to 20 ºC.

The preferred temperature range is 15 ºC to 20 ºC.

It is important to bring products to room temperature (18 - 20 ºC) before mixing and use

Guaranteed shelf life: At least 48 months in original sealed containers.

The information provided in this documentation has been carefully selected and arranged by us. It is based upon our best knowledge on the subject at the date of issuance. The Information is given for information purposes only. We are not liable for its correctness, accuracy and completeness. It is up to the user to check the information with regard to up-to-dateness and suitability for his intended purpose.

The relevant Material Safety Data Sheet and Warnings displayed on the product label need to be observed.

The intellectual property in this Information, including patents, trademarks and copyrights, is protected. All rights reserved.

We may modify and/or discontinue operation of all or portions of this Information at any time in our sole discretion, without notice and assume no responsibility to update the Information. All rules set forth in this clause shall apply accordingly for any future changes and amendments.

Spies Hecker Wedgwood Way Stevenage Hertfordshire SG1 4QN

Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730

www.spieshecker.co.uk Spies Hecker. A member of DuPont Performance Coatings(UK) Limited.

2.1.8



Permahyd® Base Coat Series 280 is a high performance waterborne product based on special P.U. resin dispersions. It is suitable for use on all two and three-stage solid and metallic finishes on passenger cars and commercial vehicles.

For professional use only! VR Technical Data Sheet No. 280/10/99 - UK

280 10 / 99 - UK

Substrate

Suitable substrates: Permasolid® HS Primer Surfacer 5110 Permahyd® 1K Primer Surfacer 4100 Sanded OEM or existing paintwork Permacron® 1:1 Elastic Surfacer 3300 for plastics Permasolid® HS Express Surfacer 5250 Priomat® 1K Wash Primer 4085 aerosol Permasolid® HS Wet on Wet Surfacer 5330 Permasolid® SpectroFlex 5400

Substrate pre-treatment:

Clean original or old finishes and Permasolid® or Permacron® surfacers thoroughly with Permahyd® Silicone Remover 7080. Heavy contamination may be removed by using Permaloid® Silicone Remover 7010 initially. Dry sand with random orbital sander and dust extraction P400-500 or wet with P600-800.

Allow wet sanded surfacer to dry thoroughly. Carefully clean sanded surfaces once more before further treatment with Permahyd® Silicone Remover 7080 to remove all dust, sanding residues and other impurities. Ensure all traces of Permahyd® Silicone Remover 7080 are removed before application of Series 280 Base Coat.

Important note: Remove Silicone Remover with a lint-free cloth such as Tork 606 and allow to dry completely.

Do not use coloured non-woven cleaning cloths with Permahyd® Silicone Remover 7080.

Sanded through areas must be isolated with Permahyd® 1K Primer Surfacer 4100 or 4085 aerosol. If 1K Surfacer 4100 or 4085 is not used, the bare metal should first be coated with 1K Priomat Product before Permacron® or Permasolid® 2K Surfacer is applied. DO NOT APPLY SERIES 280 BASE COAT DIRECTLY TO 1K PRIOMAT PRODUCTS

280 10 / 99 - UK

Application

Mixing containers: Plastic containers or cans with coated interiors

Strainers / filters: Material and glue should be waterproof

Reducer: Permahyd® Demineralised Water 6000


Compliant Gravity feed

HVLP Gravity feed


22-26 seconds DIN 4/20 ºC



approx. 10 to 15% by volume or weight

Spray nozzle:*

Gravity feed

1.2 to 1.3mm WSB to 1.3mm

Spray pressure:* For recommended spraying pressure refer to spraygun manufacturer


No. of coats:

apply a tack coat, followed by 1 normal full coat* 1 operation = 1.5 coats

* With low opacity colours it may be necessary to apply one or two more coats after an appropriate flash-off time. In these cases apply single coats and only continue after the previous coat has dried to a matt surface appearance.


12 – 15 µm

280 10 / 99 - UK

Drying

Flash –off time: approx. 20 minutes at 20 º C ambient temperature

Flash-off times may be reduced by the use of the following methods:

Small areas Surface matting can be accelerated by blowing with SATA Dry Jet (or similar) air diffuser. It is also possible to blow with the spray gun after a waiting time of at least 5 minutes.

Drying time with this method: approx. 5 minutes.

Larger areas Surface matting can be accelerated by using infrared or low baking. IR medium wave approx. 4 minutes IR short wave approx. 3 minutes cooling time approx. 5 minutes

force drying at + 40 ºC combi booth set booth to 40 ºC on spray cycle; leave for 10 minutes oven approx. 5 minutes. cooling time approx. 5 minutes.

*Flash-off and drying times depend on the temperature, humidity and air settling rate.

Further steps:

Recoat with:

After flash-off times given, recoat with Permasolid® HS Clear Coat 8035 Permasolid® HS Clear Coat 8030 Permasolid® HS Clear Coat 8600 Permasolid® HS Diamond Clear Coat 8450 Permacron® Elastic Clear Coat Satin Gloss 8070

Please refer to relevant technical data sheets for full details.

280 10 / 99 - UK

Special Note Blend-in system to avoid a visible difference between the repair and surrounding areas:

a) Preparation: Sand surfacer (dry with P360-500 or with waterproof paper P600-800). Thoroughly sand surrounding areas not coated with surfacer using a fine sanding pad (3M 7448). Clean the entire surface well with Permahyd® Silicone Remover 7080 to remove all dust, sanding residues and other impurities. Remove excess Silicone Remover with a lint-free cloth, avoiding streaks. Allow wet-sanded and cleaned surfaces to dry completely.

b) Blend in system for metallics and solid colours: Apply a full coat of base coat to the surfaced area at ready-to-spray viscosity. Spray each coat a little further into the transition area, thus creating a dust coat ring around the repair. Spray the fade-out zone wider and blend in lightly with reduced pressure. After the appropriate final flash-off time, apply clear coat.

280 10 / 99 - UK

Technical Data


Flash point: Base Coat Series 280 above +23OC

Solids content: base coat without reducer white black silver

% by wt. approx. 37.3 approx. 22.8 approx. 16.9 % by vol. approx. 23.7 approx. 20.1 approx. 13.7

S.G. approx 1.19 g/m3 1.02 g/m3 1.02 g/m3

Coverage*: approx 15.8 m2/l 13.4 m2/l 11.4 m2/l

at 15 µm dry at 12 µm dry film thickness film thickness

Solids content: ready for spraying white black silver

% by wt. approx. 34.4 approx. 20.8 approx. 15.4 % by vol. approx. 21.6 approx. 18.3 approx. 12.4

S.G. approx 1.18 g/m3 1.02 g/m3 1.02 g/m3

Coverage*: approx 14.4 m2/l 12.2 m2/l 10.3 m2/l

at 15 µm dry at 12 µm dry film thickness film thickness

*The coverage has been calculated based on the recommended dry film thickness and the solids content by volume.

No allowance has been made for wastage during application.



280 10 / 99 - UK

Special Note:

Product application: Spraying equipment must be suitable for the application of waterborne products: Manufacturers instructions must be followed.

Cleaning of spray guns and equipment:

Rinse with Permahyd® Demineralised Water 6000 before and after use. Then rinse with clean nitro thinner or gunwash to remove dried residues.

Waste management: Spies Hecker advise that should coagulation of waste be required then permission to dispose of the liquid residue in drainage system is obtained from Local Water Authority.

Spies Hecker do not make available coagulants - however, these are commercially available.

Storage All paint products must be stored in dry conditions within the temperature range 5 ºC to 20 ºC.



280 10 / 99 - UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730

www.spieshecker.co.uk Spies Hecker. A member of DuPont Performance Coatings (UK) Limited.

2.1.9



Permahyd® Base Coat Series 285 is a high performance waterborne product based on special P.U. resin dispersions. It is suitable for use on all two and three-stage pearl finishes on passenger cars and commercial vehicles.


285 / 10 / 99 - UK

Substrate

Suitable substrates:

Permasolid® HS Primer Surfacer 5110 Permahyd® 1K Primer Surfacer 4100 Sanded OEM or existing paintwork Permacron® 1:1 Elastic Surfacer 3300 for plastics Permasolid® HS Express Surfacer 5250 Priomat® 1K Wash Primer 4085 aerosol Permasolid® THS Wet on Wet Surfacer 5330 Permasolid® SpectroFlex 5400


Clean original or old finishes and Permasolid® or Permacron® surfacers thoroughly with Permahyd®

Silicone Remover 7080. Heavy contamination may be removed by using Permaloid® Silicone Remover 7010 initially. Dry Sand with random orbital sander and dust extraction P400-500 or wet with P600-800. Allow wet sanded surfacer to dry thoroughly. Carefully clean sanded surfaces once more before further treatment with Permahyd® Silicone Remover 7080 to remove all dust, sanding residues and other impurities. Ensure all traces of Permahyd® Silicone Remover 7080 are removed before application of Series 280 Base Coat.



Sanded through areas must be isolated with Permahyd® 1K Primer Surfacer 4100 or 4085. If 1K Surfacer 4100 or 4085 is not used, the bare metal should first be coated with 1K Etch Primer before Permacron® or Permasolid®2K surfacer is applied.

COAT DO NOT APPLY SERIES 285 BASE DIRECTLY TO 1K Priomat Products.

285 / 10 / 99 - UK

Application

Mixing containers: Plastic containers or cans with coated interiors



1. Initial coat A special ground coat is only necessary for three-stage pearl colours: Apply Permahyd® Base Coat Series 280 (for colour, see the back of the label on Permahyd®

Pearl Base Coat Series 285, the microfiche or Colour Program).

2. Pearl coat: Apply Permahyd® Pearl Base Coat Series 285


Compliant HVLP





approx. 10 to 15% by volume or weight

Spray nozzle:*

1.2 to 1.3mm WSB to 1.3mm

Spray pressure:* For recommended spraying pressure refer to spraygun

manufacturer


285 / 10 / 99 - UK

No. of coats:

apply a tack coat, followed by 1 normal coat* 1 operation = 1.5 coats

*With low-opacity colours it may be necessary to apply one or two more coats after an appropriate flash-off time (matted surface). Flash-off can be accelerated by blowing with a spray gun or SATA Dry Jet after waiting 5 minutes. The total film thickness (including the ground coat in Series 280) must not exceed 45microns.


12 – 15 µm

Drying

Flash – off time:

approx. 20 minutes at 20 º C ambient temperature

Flash-off times may be reduced by the use of the following methods:

Small areas Surface matting can be accelerated by blowing with SATA Dry Jet (or similar) air diffuser. It is also possible to blow with the spray gun after a waiting time of at least 5 minutes.

Drying time with this method: approx. 5 minutes.

Larger areas Surface matting can be accelerated by using infrared or low baking. IR medium wave approx. 4 minutes IR short wave approx. 3 minutes cooling time approx. 5 minutes

force drying at + 40 ºC combi booth set booth to 40 ºC on spray cycle; leave for 10 minutes oven approx. 5 minutes. cooling time approx. 5 minutes.

*Flash-off and drying times depend on the temperature, humidity and air settling rate in the booth, and on the number of coats. The surface must be allowed to matt completely in all cases.

285 / 10 / 99 - UK

Further steps:

Recoat with: After flash-off times given, recoat with Permasolid® Clear Coat 8035 Permasolid® HS Clear Coat 8030 Permasolid® HS Clear Coat 8600 Permasolid® HS Diamond Clear Coat 8450 Permacron® Elastic Clear Coat Satin Gloss 8070

Please refer to relevant technical data sheets for full details.

Special Note 1. The OEM finish dictates whether a two-stage or three-stage pearl colour (with special ground colour) is required. The appropriate ground coat colour is given on the microfiche and in the Colour Program.

2. Blend-in system to avoid a visible difference between the repair and surrounding areas:

a) Preparation:

Sand surfacer (dry with P400-500 or with waterproof paper P600-800). Thoroughly sand surrounding areas not coated with surfacer using a fine sanding pad (3M 7448). Clean the entire surface well with Permahyd®

Silicone Remover 7080 to remove all dust, sanding residues and other impurities. Remove excess Silicone Remover with a lint-free cloth, avoiding streaks. Allow wet-sanded and cleaned surfaces to dry completely.

b) Two-stage pearl colours:

Apply Pearl Base Coat Series 285 to the surfaced area at ready-to-spray viscosity until the surfacer is fully covered. Overlap each coat a little further onto the original finish area to creating a dust coat transition area around the repair. Reduce the spray pressure and apply a fine coat to the dust coat transition area, overlapping still further onto the original finish. After an appropriate final flash-off the clear coat can be applied.

285 / 10 / 99 - UK

c) Three-stage pearl colours:

Apply a thin coat of Base Coat Series 280 (ground coat colour) at reduced pressure to the surface area. Spray the same area with Pearl Base Coat Series 285 at ready-to-spray viscosity at reduced pressure, overlapping slightly to match the original finish.

Technical Data

Viscosity as supplied: 35-40 seconds

Flash point: Base Coat Series 285 above +23 °C

Solids content: base coat without reducer

approx. 27.0% by weight approx. 18.0% by volume

ready for spraying

approx. 24.6 % by weight approx. 16.3% by volume

S.G. approx. 1.10g/m3 approx. 1.09g/m3

Coverage* approx. 15.0 m2/l at 12 µm dry film

thickness

approx. 13.6 m2/l at 12 µm dry film

thickness



Storage

Store away from frost! Storage temperature between +5 ºC to +30 ºC. Temperatures below or above this lead to deterioration of the product.


285 / 10 / 99 - UK

Special Note:

Product application: Spraying equipment must be suitable for the application of waterborne products: Manufacturers instructions must be followed.


Rinse with Permahyd® Demineralised Water 6000 before and after use. Then rinse with clean nitro thinner or gunwash to remove dried residues.


Spies Hecker do not make available coagulants - however, these are commercially available.

285 / 10 / 99 - UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730


www.spieshecker.co.uk

2.1.11


Permasolid® HS Automotive Topcoat Series 270 Permasolid® HS Automotive Topcoat Series 270 is a 2K high-solid acrylic product, designed for complete, partial or local repairs of single layer passenger car finishes.

Permasolid® HS Automotive Topcoat Series 270 displays very high build, excellent gloss, and fast drying properties with excellent physical and chemical resistance.


270/10/99-UK

Substrate 1. Fully cured, well preserved original or old paintwork.

2. Permasolid® HS Surfacer plus 5110 Permahyd® 1K Primer Surfacer 4100 Permasolid® HS Express Surfacer 5250 Priomat® 1K Wash Primer 4085 aerosol Permacron® 1:1 Elastic Surfacer 3300 for plastics Permasolid® HS Wet on Wet Surfacer 5330 Permasolid® SpectroFlex 5400

Preparation of substrate: 1. Sand original or old paintwork with either wet P600-800, dry P400-500.

2. Sand primer surfacers as per individual TDS Clean with Permaloid® Silicone Remover 7010.

Application

Mixing Ratio:

2:1 by volume with Permasolid® HS Hardener 3315 slow 2:1 by volume with Permasolid® HS Hardener 3310 2:1 by volume with Permasolid® HS Hardener 3307 Extra fast (for smaller repairs up to 3 panels

Pot Life: Approx. 90 minutes at +20 ºC


Compliant HVLP


19 - 21 seconds DIN 4/20 ºC

19 - 21 seconds DIN 4/20 ºC


Not required



manufacturer


270/10/99-UK

No. of coats:

a)1 application: 1 grip coat followed by 1 full coat without flash-off between coats

b) 2 coats with 5 minutes flash-off time between coats

Note: With low opacity colours it may be necessary to apply a further 1 coat after the appropriate flash-off time


50- 60 µm dry film thickness.

Special note: Reducers 3364, 3380 0r 3365 or Permacron® Speed Blender 1035 should be used to achieve blend-in on spot repaired areas.

Drying

Air drying:


Dust free: 40-50 minutes Dry for handling: 4-6 hours Thorough dry: overnight

Force Drying:

Flash-off time:

approx: 5-10 minutes

drying time and temperature: 20 minutes at 60 ºC metal temperature 3307 30 minutes at 60 ºC metal temperature 3310/3315

DO NOT ADD ANY ADDITIONAL REDUCER.

Infrared drying:

Flash-off time: approx: 5 minutes distance: approx. 60 cms drying time: short wave 10-15 minutes medium wave 15-20 minutes

270/10/99-UK

Storage: All paint products must be stored in dry conditions within the temperature range 5 ºC to 20 ºC.


Guaranteed shelf life: At least 48months in original sealed containers.

Solids content: Base material mixed

white black white black approx. 74% by wt. approx. 61% by wt approx. 68% by wt. approx. 58% by wt. approx. 59% by wt. approx. 55% by wt approx. 54% by wt. approx. 52% by wt.

S.G: approx. 1.25g/cm3 approx. 1.01 g/cm3

Coverage:* approx. 10.8m2/L approx. 10.4m2/L

at 50µm dry film thickness

*The coverage has been calculated on the basis of the recommended dry film thickness and the solid content by volume of the mixture (without reducer). No allowance has been made for wastage during application.

VOC Content: The EU limit for this product (2004/42/IIB(d)(420) 420) in ready for use form is max. 420g/litre of VOC. The VOC content of this product in ready to use form is max. 420g/litre


270/10/99-UK

Technical Data

Viscosity as supplied: at least 100 seconds

Flash point: base material and hardener over +21 ºC

Special Note: It is important to bring products to room temperature (18 - 20 ºC) before mixing and use. Optimum application results will be obtained by ensuring this procedure is followed. It is also important to follow the recommended application procedure. Failure to do so can lead to excessive film thickness and slower drying. In order for the system to remain VOC compliant, additional reducer should not be added in normal application. .

270/10/99-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730

Spies Hecker. A member of DuPont Performance Coatings (UK) Limited.


2.1.12


Permacron® Elastic Clear Coat 8070 Satin Gloss Permacron® Elastic Clear Coat 8070 is a satin gloss Clear Coat from our 2K acrylic system. It is particularly suitable for two-stage finishes on plastic parts (e.g. Mercedes-Benz bumpers and lower body panels). Permacron® Elastic Clear Coat 8070 is characterised by high elasticity and excellent levelling.

For VOC compliance this product is classified as a “Special Product”.


8070/10/99-UK

Substrate

Suitable base coats: Surfaces coated with Permahyd® Base Coat Series 280/285

Application

Mixing Ratio:

2:1 by volume with Permacron® MS Hardener express 3333 New (for larger areas and higher temperatures) or Permacron® MS Hardener express 3355 New (for smaller areas and fast repairs).

Pot Life: Ready for use approx. 6 hours at +20 ºC


Compliant HVLP


18 to 20 seconds DIN 4/20 ºC

18 to 20 seconds DIN 4/20 ºC


Not required



manufacturer

No. of coats:

a)1 operation = 1 tack coat followed by 1 full coat without flash-off time b) 2 coats with 5 minutes flash-off time




8070/10/99-UK

Drying at 20 °C ambient temperature

Air drying:

Dust free: 40-50 minutes Dry for handling: 4-6 hours Thorough dry: overnight

Flash-off time:

approx. 5-10 min.

Force Drying:

40 mins @ 60°C object temperature.

Storage: At least 48 months in original sealed containers.

Guaranteed shelf life: Clear Coat and Hardener - At least 12 months in original sealed containers.

Technical Data

Viscosity as supplied: Elastic Clear Coat 8070 40 - 45 sec.

Flash point: base material and hardener over +21 ºC

Solids content: (without reducer)

base material mixed

approx. 50% by weight 41% approx approx. 33.5% by volume approx. 30.5% by volume

S.G: approx. 1.04% approx. 1.02g/cm3

Coverage:* approx. 6.1 m2/L at 50µm dry film thickness

8070/10/99-UK



Special Note: It is important to bring products to room temperature (18 - 20 ºC) before mixing and use.

Optimum application results will be obtained by ensuring this procedure is followed.

It is also important to follow the recommended application procedure. Failure to do so can lead to excessive film thickness and slower drying.

In order for the system to remain VOC compliant, additional reducer should not be added in normal application.

8070/10/99-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.1.15


Permasolid® HS Clear Coat 8035 Permasolid® HS Clear Coat 8035 is a high gloss, high solids clear coat from our acrylic range.

Thanks to its high solid content and excellent build, it can be applied efficiently in one application. HS Clear Coat 8035 is very economic in use and provides increased productivity through its greater surface coverage and short processing time. Its high resistance to the effects of weathering and environmental pollution ensure a durable protective paint film.


8035/01/02-UK

Substrate

Suitable base coats: Permahyd® Base Coat Series 280 Permahyd® Pearl Base Coat Series 285

Application

Mixing Ratio:

2:1 by volume with Permasolid® HS Harderner 3307 Extra Fast (for small areas up to 3 panels) 2:1 by volume with Permasolid® HS Hardener 3310 2:1 by volume with Permasolid® HS Hardener 3315 slow

Pot Life: Approx. 60-90 minutes at 20 °C ready for use.


Compliant HVLP


22 seconds DIN 4/20 ºC



Not required

Spray nozzle:* 1.2to 1.3mm 1.3 to 1.4mm


manufacturer

No. of coats:

1 application : 1 grip coat followed by 1 full coat without flash-off between coats




8035/01/02-UK


Air drying:

Dust free: 20-30 minutes Dry for handling: 4-5 hours Through dry: overnight

Flash-off time:

approx. 5-10 min.

Low baking:

drying time and temperature: 15 minutes at 60 °C metal temperature using hardener 3307

25 minutes at 60 °C metal temperature using hardener 3310

30 minutes at 60 °C metal temperature using hardener 3315

For fast smaller repairs (up to 3 panels), use hardener 3307 Extra Fast. For larger areas use Hardener 3310 fast, or 3315 slow.

Storage:


Technical Data


Flash point: Clear Coat and hardener over 23 °C


Base material approx. 62.7% by weight approx. 56.5% by volume

Mixed approx. 57.9% by weight approx. 51.4% by volume

S.G: approx. 1.02g/cm3 approx. 1.01 g/cm3

8035/01/02-UK

Coverage:* approx. 10.3 m2/1 at 50 µm dry film thickness



8035/01/02-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.1.18


Permasolid® HS Optimum Clear Coat 8600 Permasolid® HS Optimum Clear Coat 8600 is a high gloss, high solids clear coat from our HS acrylic range.

Thanks to its high solid content and excellent build, it can be applied efficiently in one application. Permasolid® HS Clear Coat 8600 is produced with performance characteristics that exceed all others available today. Thanks to the application of patented and futuristic technology, called “HyperCure®”, this new HS Clear Coat combines rapid and easy application with a brilliant finish, and drying performance that is exemplary.


8600/02/04-UK

Substrate


Application

Mixing Ratio:

3:1 by volume with Permasolid® VHS Hardener 3220 express 3:1 by volume with Permasolid® VHS Hardener 3230 3:1 by volume with Permasolid® VHS Hardener 3240

Pot Life: Approx. 80-100 minutes at 20 °C ready for use.


Compliant HVLP





Not required



manufacturer

No. of coats:




45-55 µm dry film thickness.

8600/02/04-UK


Air drying:

Dust free: 20-30 minutes Dry for handling: 4-5 hours Through dry: overnight

Force drying:

Flash-off time:

approx. 5-10 min.

Drying time:

drying time and temperature:

VHS Hardener 3220 express (spot repair / partial refinish) 15-20 minutes at 60 °C metal temperature

VHS Hardener 3230 (larger areas/ full refinish) 25-30 minutes at 60 °C metal temperature

VHS Hardener 3240 (large areas/full refinish/high temperatures) 30mins at 60°C metal temperature.

Infrared drying:

Flash-off time: 5-10 minutes

Drying time: short wave 8-12 minutes medium wave 12-14 minutes

Technical Data

Viscosity as supplied: 30-40 seconds

Flash point: Clear Coat and Hardener over 23 °C


mixed 3:1 with VHS Hardener 3230 approx. 55.4% by weight approx. 46.2% by volume

S.G: approx. 0.98 gms/cm3

8600/02/04-UK

Coverage:* approx. 10.3 m2/1tr at 45µm dry film thickness

*The coverage has been calculated on the basis of the recommended dry film thickness and percentage solid content by volume. No allowance was made for wastage during application.



Storage: All paint products must be stored in dry conditions within the temperature range 5 ºC to 20 ºC.



It is important to bring products to room temperature (18 - 20 ºC) before mixing and use.




8600/02/04-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.1.20


Permasolid® HS Diamond Clear Coat 8450

Permasolid® HS diamond Clear Coat 8450 is a VOC compliant high solid clear coat. It is used to refinish vehicles which were coated originally with an OEM clear coat that has a higher scratch resistance.

• High mechanical and chemical resistance

• Easy to use

• Durable gloss

• Very good polishing properties


8450/08/05 - UK

Substrate


Application

Mixing Ratio:

3:1 by volume with Permasolid® VHS Hardener 3240.

Pot Life: Ready for spraying approx. 80-100 minutes @ 20 ºC.


Compliant HVLP


Mixing viscosity


Not required

Spray nozzle:* 1.2-1.3mm 1.3 to 1.4mm

Spray pressure:* For recommended spraying pressure

refer to manufacturer of spray gun

0.7 bar

No. of coats:



45-55µ

When applying this clear coat the first half coat should be a light, almost closed coat followed immediately by a full coat.

8450/08/05 - UK

Drying

Air drying:

@ 20 ºC ambient temperature Dust free 70-80 minutes Dry for handling 4-6 hours Through dry overnight

Force drying:

Flash-off: approx 5 minutes

Drying time and temperature:

30-35 minutes @ 60 °C metal temperature

Infrared drying:

Flash-off time:

approx: 5 minutes

Infrared drying:

Drying time and temperature short wave, 8-12 minutes

8450/08/05 - UK

Technical Data

Viscosity as supplied: 46 secs (iso 4mm at 23°C)

Flash point: 41.5 ºC.

Solids content: HS Diamond Clear Coat 8450

approx 49.3% by weight approx 41.0% by volume

mixed with 3:1 with VHS Hardener 3240

approx. 55.0% by weight approx. 47.1% by volume

S.G. approx. 0.97 g/cm3 approx. 0.99 g/cm3

Coverage* approx 9.4 m2/ltr at a dry film thickness of 50µm. *The coverage has been calculated on the recommended dry film thickness and the percentage volume solids (without any additional reducer). No allowance was made for wastage during application.



Storage

All paint products must be stored in dry conditions within the temperature range 5 ºC to 20 ºC. The preferred temperature range is 15 ºC to 20 ºC.


It is important to bring products to room temperature (18-20OC) before mixing & use

Optimum application results will be obtained by ensuring that this procedure is followed.

It is also important to follow the recommended application procedure. Failure to do so can lead to excessive film thickness and slower drying

Additional reducer is only permitted to achieve blend-in on spot repairs.

8450/08/05 - UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.2.1


Priomat® One Pack Primer 7119 aerosol pack Field of application: Passenger cars. One component primer for steel and galvanised substrates. Thanks to its special pigment and binding agent composition it offers excellent anti-corrosion properties and extremely good adhesion.

Raw material base: polyvinylbutyral, special anti-corrosion pigments.

For professional use only! VR Technical Data Sheet No.7119/10/99-UK

7119/10/99-UK

Substrate

Suitable substrates: 1. Steel

2. Galvanically or electrolytically zinc-coated steel sheet and soft aluminium surfacers.

Surfacers which have been fully puttied and then fine sanded with the following products: Raderal®

Vario Putty 2035 beige, Permacron® Fine Putty 7715.

Important note: In view of the multitude of alloys and methods of production used for metals, an initial test application should always be made on the planned substrate to ensure that the pre-treatment is going to provide perfect adhesion.

Substrate pre-treatment: Remove all grease, then lightly sand steel, galvanically / electrolytically zinc-coated steel sheet or soft aluminium.

Prior to pre-coating, clean all the substrates with Permacron® Silicone Remover 7010.

Application

Method of application: Aerosol Can

Distance to object: 15-20cm

Spray nozzle: wide fan nozzle

Number of Coats: 2-3 coats with intermediate flash-off time of approx. 5 minutes

Note: After use, hold aerosol upside down and spray briefly to clean nozzle.

7119/10/99-UK


Air drying:

re-coatable: with Solventborne after 10-15 minutes sandable: if required after 45-60 minutes

Further Treatment: Re-coatable with:

Permasolid® HS Surfacer plus 5110 beige/grey Permasolid® SpectroFlex 5400

Special Notices

1. Do not recoat with polyester products.

2. Do not use on thermoplastic finishes.

3. Do not recoat with topcoat products.

Dry sanding:

With orbital sander P 400-500 grit

Wet sanding

With sanding paper P 800-1000 grit

Technical Data


Storage conditions:

Solids content: S.G.

VOC content:

Storage between 20-25 °C

12.92%

0.77g/cm3

The EU limit for this product (2004/42/IIB(e)(840) 840)in ready for use form is max. 840g/litre of VOC. The VOC content of this product in ready to use form is max. 840g/litre. *VOC values determined in practice according to ISO 11890/2

7119/10/99-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.2.2


Permasolid® HS Surfacer Plus 5110 Grey Permasolid® HS Surfacer plus 5110 beige is a high quality two component acrylic product for use in the vehicle refinishing industry. This surfacer has a high solids content and requires no additional thinner thereby ensuring economical and environmentally friendly application.

Due to its high filling power and stability it can be applied at high film thicknesses. Quick drying and good levelling properties ensure economical application and easy sanding.

Permasolid® HS Surfacer plus 5110 offers good sealing properties on sensitive substrates as well as excellent top coat quality.


5110/10/99-UK

Substrate

Suitable substrates: 1. Bare steel, coated with Priomat® 1K Primer.

2. Galvanised steel or soft aluminium degreased and coated with Priomat® 1K Primer.

3. Sanded original or old paintwork (not thermoplastic paintwork)

4. Original paintwork, thoroughly degreased, and finely sanded.

5. Surfaces filled with the following products and then finely sanded: Vario Putty 2035 / Fine Putty 7715.

6. GRP substrates, free of release agent cleaned and sanded.

7. Unsanded, well precleaned electrocoated panels.

Pretreatment: Degrease and lightly sand.

Prior to recoating clean substrate once more before further treatment with Permaloid® Silicone Remover 7010.

Important Note: In order to guarantee optimum corrosion protection we recommend all bare metal edges and surfaces be coated with a Priomat® 1K Primer.

Application

Mixing Ratio:

4:1 by volume with Permacron® MS Hardener express 3355 New. It is possible to use other Permacron®

Hardeners. (Please contact Spies Hecker Technical Department before using any other Permacron®

Hardeners.

Pot Life: Approx.60-90 minutes at 20 °C ready for use.

5110/10/99-UK


Compliant HVLP


4:1 mixing viscosity


Not required

Spray nozzle:* 1.5 to 1.8 mm 1.5 to 1.9mm


manufacturer

No. of coats:

2 to 4 coats = 80 to 200µm according to nozzle





Air drying:

at 20 ºC ambient temperature: 80 -120µm 3-4 hours before sanding 120 - 250µm overnight drying before sanding

Force drying:

Flash-off time:

5 -15 mins.

Drying time:

80 -120µm 30 min. at 60 ºC metal temperature. 120 - 200 µm 40 mins at 60 ºC metal temperature.

Infrared drying:


Drying time: 80 -120µm 15 mins. 120 - 200 µm 20 mins.

5110/10/99-UK

Further steps

Dry sanding:

With orbital sander P 320 -500 grit

Wet sanding

With sanding paper P 600 - 800 grit

Recoatable with: Permahyd® Base Coat Series 280/285 Permasolid® HS Topcoat Series 270

Special Tips 1. In order to facilitate sanding apply Control Paint black before sanding. Do not apply on wet Surfacer.

2. Substrate defects can be filled with Raderal® Putty. After drying and intermediate sanding seal puttied areas with HS Surfacer 5110.

3. Sensitive and puttied areas are best sealed with a medium film thickness of 80 - 120µm in approx. two coats and air drying overnight or low baking / IR drying.

4. With sensitive substrates thorough pre-treatment is required and the whole area has to be coated with Surfacer

5. For sealing thermoplastic paintwork we recommend Vario Primer Surfacer 8590 Beige, or Permasolid® VHS Surfacer 5150.

6. For air drying we recommend a minimum temperature of 15 ºC

Technical Data

Viscosity as supplied: Thixotropic

Flash point: HS Surfacer plus hardener - above 23 ºC


HS Surfacer plus 5110 approx. 68.0% by weight approx. 43.8% by volume

mixed with Hardener 3355 approx. 63.4% by weight approx. 40.6% by volume

S.G: 1.56g/cm3

5110/10/99-UK

Coverage:* approx. 5.1m2/L at a dry film thickness of 80µm

approx. 2.0 m2/L at a dry film thickness of 200µm

*The coverage has been calculated on the basis of the recommended film thickness and the solid content by volume (without reducer). Calculations are based on 100% transfer efficiency.

VOC Content: The EU limit for this product (2004/42/IIB(c)(540) 540) in ready for use form is max. 540g/litre of VOC. The VOC content of this product in ready to use form is max. 540g/litre


Storage All paint products must be stored in dry conditions within the temperature range of 5-20 ºC.

The preferred temperature range is 15-20 ºC.


Special note It is important to bring products to room temperature (18-20 ºC) before mixing and use.


In order for the system to remain VOC compliant, additional reducer should not be added.

5110/10/99-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.2.7


Permahyd® 1K Primer Surfacer 4100 Permahyd® 1K Primer Surfacer is a waterborne product developed for complete panel or partial repair of bare metal areas on vehicle bodywork. It is particularly suitable for lower film build repairs in economical refinishing.


4100/10/99-UK

Substrate

Suitable substrates: 1. Steel, galvanised steel, soft aluminium

2. Sanded OEM primers

3. Sanded OEM or old paintwork

4. Surfaces prepared with Raderal 2K polyester products and finely sanded

Pretreatment: 1. Steel, galvanised steel, soft aluminium: degrease and sand lightly.

2. OEM primer clean and sand lightly.

3. OEM or old paintwork clean and sand lightly, remove all traces of rust and sand area around rusted spots.

Important Note: Remove Silicone Remover with a lint-free cloth such as Tork 606 and allow to dry completely.


Application



Mixing Ratio:

5 to 10% (measure carefully)

Pot Life:

4100/10/99-UK


Compliant HVLP


23 to 28 seconds


5 to 10% (measure carefully)

Spray nozzle:* 1.4 to 1.5mm 1.5 to 1.7 mm


manufacturer

No. of coats:

2 to 3 (with intermediate flash off*)




Drying

Air drying:

at +20 ºC ambient temperature recoatable: after 30-60 minutes (dependent on

thickness applied)

sandable: approx. 3 hours

Force drying:

flash-off time*: 5 minutes at +20 ºC

drying time and temperature: approx. 30 minutes at +60 ºC metal temperature

4100/10/99-UK

Infrared drying: flash-off time*: approx. 5 minutes at +20 ºC

short wave: 5 minutes at level I (50% power) and then 10 minutes at level 2 (100% power)

medium wave: 20 minutes

Note: * The flash-off and curing times depend on the temperature, humidity and air settling rate in the spray booth. Wet-on-wet recoating with topcoat may also be reduced by the use of a SATA Dry Jet (or similar) air diffuser. 5 minutes ambient flash-off must be left before using this method.

Further steps

Dry sanding:

With random orbital sander and dust extraction P400-500 grade.

Wet sanding

With P 800-grade paper.

Recoatable with: 1. Permahyd® Base Coat Series 280/285 and HS Clear Coat

2. Permasolid® 2K HS Topcoat Series 270

Technical Data



SG:

Primer Surfacer 4100 approx. 55.6% by weight approx. 39.05% by volume

approx. 1.38 g/cm3

4100/10/99-UK

Coverage:* approx. 7 8 m2/l at 50 µm dry film thickness

* The coverage has been calculated on the basis of the recommended dry film thickness and the solids content by volume (without reducer). No allowance has been made for wastage during application.



Storage

Storage temperature between 5 ºC to 30 ºC.

DO NOT ALLOW PRODUCT TO FREEZE



Product application: Spraying equipment must be suitable for the application of water-borne products: Manufacturers instructions must be followed.


Rinse with Permahyd® Demineralised Water 6000 before and after use.


Spies Hecker does not make available coagulants - however, these are commercially available.



4100/10/99-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.2.16


Permasolid® SpectroFlex 5400 Permasolid® SpectroFlex 5400 is a high solid 2 component acrylic surfacer system. It provides users with a flexible range of uses from medium build sandable surfacer to a very rapid drying wet-on-wet surfacer.

This may be used conventionally and recoated with Spies Hecker basecoats or topcoats or as a coloured “sealer” for interior surfaces of engine bays etc.

Replication of OE surfacer colours can be achieved by intermixing of the six coloured surfacers in the system using formulations shown in the system’s colour swatch.


5400/02/03-UK

Substrate

Suitable substrates: 1. Bare, sanded steel sheet, cleaned, sanded and primed with Priomat® Primer.

2. Galvanically or electrolytically zinc-coated steel sheet or soft aluminium surfaces which have been cleaned, sanded and primed with Priomat® Primer.

3. Lightly sanded original or old finish.

4. Finely sanded, thoroughly cleaned, original primed surfaces.

5. Surfaces which have been finely puttied with the following products and then finely sanded: Raderal® IR Premium Putty 2035

6. Unsanded, well precleaned electrocoated panels.

7. UP-GP substrates, free of release agent, cleaned and sanded.

Pretreatment: Carefully degrease and lightly sand.

Before further treatment, clean all substrates once more with Permaloid® Silicone Remover 7010

Special note: To guarantee optimum corrosion protection, we recommend coating any remaining corners and edges as well as sanded through spots with Priomat® Wash Primer 4075 or Priomat® 1K Wash Primer 4085.

Application as interior colour

Mixing Ratio:

2:1 by volume with:

Permasolid® HS Hardener 3307 extra fast Permasolid® HS Hardener 3310 Permasolid® HS Hardener 3315 Slow

Pot Life: RFU mixture approx. 30-45 minutes at 20ºC (depending on hardener).

Additive: Permasolid® SpectroFlex Additive 5407.

5400/02/03-UK


Compliant HVLP


16 seconds

Added Additive @ 20°C material temperature

approx. 20%



manufacturer

No. of coats:

1 to 3 = 50 to 80 µm

When used as interior, it is not necessary to recoat with top coat


Wet on Wet Application

Mixing Ratio:

2:1 by volume with: Permasolid® HS Hardener 3307 extra fast Permasolid® HS Hardener 3310 Permasolid® HS Hardener 3315 slow

Pot Life: RFU mixture approx. 30-45 minutes at 20ºC (depending on the hardener)

Additive: Permasolid® SpectroFlex Additive 5407

5400/02/03-UK


Compliant HVLP


16 seconds

Added Additive @ 20°C material temperature

approx. 20%



manufacturer

No. of coats:

1 to 2 = 30 µm

When used as interior, it is not necessary to recoat with top coat

Flash of time: 15 mins.


Recoat with: Permasolid® HS Automotive Top Coat Series 270 Permahyd® Base Coat Series 280/285 and Permasolid® 2K HS Clear Coat

Application as a sanding surfacer

Mixing ratio:

4:1 by volume with Permasolid® HS Hardener 3307 extra fast Permasolid® HS Hardener 3310 Permasolid® HS Hardener 3315 slow

Pot Life: RFU mixture approx. 30-45 minutes at 20ºC

Reducer: Permacron® MS Dura plus 8580 Permacron® Reducer 3364 Permacron® Reducer 3380

5400/02/03-UK


18-20 seconds

Added reducer @ 20°C material temperature

approx. 15%



manufacturer

No. of coats:

2 to 4 = 60-200µm

Drying

Air drying: at 20°C ambient temperature

1. Wet-on-wet application

Recoatable:

a: After 15-20 min. (max 8 hr) with Permasolid® HS Automotive Top Coat Series 270

b. After 20-30 min. (max 8 hr) with Permahyd® Base Coat Series 280 and 285.

c. For rapid minor finishes (1 coat) after approx. 15 minutes with Permahyd® Base Coat Series 280 and 285.

2. Low -and medium-build application:

Sandable:

60-150µm 3-4 hours 150-200µm overnight

Low bake drying:

Flash-off time: 5 minutes drying time at 60°C metal temperature: 30 min. for 50-80µm 40 min. for 100-150µm

Infra-red drying

Flash-off time: approx. 5 minutes approx. 8-10 minutes depending on film thickness and whether medium or short wave.

5400/02/03-UK

Further treatment:

With intermediate sanding:

Dry sanding: with orbital sanding machine and dust extraction P-320-400 grit sandpaper

Wet sanding: with P600-800 grit sandpaper

Recoat with:

Permasolid® HS Automotive Top Coat Series 270 Permahyd® Base Coat Series 280/285 and Permasolid® 2K Clear Coat

Technical Data


Flash point: SpectroFlex and hardener - over 21°C


SpectroFlex coloured surfacer approx. 64.5 wt.% approx. 44.3%

mixed with 3310 Hardener approx. 59.7 wt.% approx. 42.9 vol%

S.G: approx. 1.33g/cm3

Coverage:* approx. 13.5 m2 / l at 30µm dry film thickness approx. 7.4m2 / l at 80µm dry film thickness

* The coverage was calculated on the basis of the recommended dry film thickness and the solids content by volume of the mixture (without reducer). No allowance was made for wastage during application.

VOC Content:* The EU limit for this product (2004/42/IIB(c)(540) 540) in ready for use form is max. 540g/litre of VOC. The VOC content of this product in ready to use form is max. 540g/litre


5400/02/03-UK

Special tips 1. In order to facilitate and optimise sanding it is imperative that Control Black be applied (spray)

2. Any blemishes appearing in the substrate can touched up using Raderal Putty. After drying and intermediate sanding isolate the putty with SpectroFlex 5400.

3. In order to achieve an optimum surface finish of top coat we recommend sanding the surfacer after overnight drying.

4. Surfacer should wherever possible, be sanded after overnight drying.

5. Infrared drying is recommended. Your attention is drawn to the instructions for use applicable to the equipment.

6. When air drying, we recommend a minimum temperature of 15°C.

7. In wet-on-wet application, allow longer flash-off times before application of Permahyd® Base Coat Series 280/285.

Storage All paint products must be stored in dry conditions within the temperature range 5 ºC to 20 ºC.




In order for the system to remain VOC compliant, additional reducer (above that shown in the TDS) should not be added.

5400/02/03-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.2.17


Priomat® 1K Wash Primer 4085 Priomat® 1K Etch Primer 4085 grey is a zinc chromate-free, one-pack product from our PVB system. It is recommended for use on bare steel, galvanised steel and soft aluminium. It is particularly suitable for spot repairs, and can be used to prime small areas of bare metal which have been sanded through.


4085/02/04-UK

Substrate


2. Electroplated/roller galvanised steel panels or soft aluminium, cleaned and sanded.

3. Lightly sanded factory primer.

4. Well sanded old or original finish (except thermoplastic finish)

5. Surfaces treated with Raderal® 2K polyester products and then finely sanded.


Pre-treatment: Remove all grease, then lightly sand steel, galvanically/ electrolytically zinc-coated steel sheet or soft aluminium lightly.

Factory primer - clean and sand lightly.

Prior to pre-coating, clean all the substrates with Permacron® Silicone Remover 7010

Application

Reducer: Permacron® Reducer 6020, Permacron® MS Dura plus 8580,Permacron Reducer 3380 or Permacron®

Reducer 3364 slow (+24 ºC)

4085/02/04-UK


Compliant HVLP


18 to 20 secs


approx 50% (2:1 by vol)



manufacturer

No. of coats:

1 - 2



Approx.20-30 µm dry film thickness

Drying

Air drying:

at 20 ºC ambient temperature:

Recoating times: with surfacer after 10-15 minutes sandable: if required after 45-60 minutes

Further Treatment Re-coatable with:

Permasolid® HS Surfacer plus 5110 grey Permasolid® HS Express Surfacer 5250 Permasolid® SpectroFlex 5400 Permasolid® HS Wet on Wet Surafcer 5330

Special Notices 1. Do not recoat with polyester products.


3. Do not recoat with topcoat products as part of a compliant coating.

4085/02/04-UK

Dry sanding:


Wet sanding


Technical Data

Viscosity as supplied: Minimum 60 seconds

Flash point: over 23 ºC

Solids content:

approx. 41.2-43.5wt.% (without added reducer) approx. 22 vol.%

S.G: 1.11 g/cm3

Coverage:* 14.6-15.1 m2/L at 15 µm dry film thickness 5.5-5.7 m2/L at 40 µm dry film thickness

* The coverage has been calculated on the recommended dry film thickness and the percentage volume solids (without any additional reducer). The associated losses during application have also been ignored.






4085/02/04-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.2.18


Priomat® 1K Wash Primer 4085

Grey aerosol pack Priomat® 1K Wash Primer 4085 grey is a zinc chromate-free, one-component product from our PVB system.

It is recommended for use on bare steel, galvanised steel and soft aluminium. It is particularly suitable for spot repairs, and can be used to prime small areas of bare metal which have been sanded through, before Permahyd® Base Coat Series 280/285 is applied.

Available in “Spray Max” aerosol cans, the product is suitable for fast and convenient application.

For professional use only! VR Technical Data Sheet No.4085a/02/04-UK

4085a/02/04-UK

Substrate


2. Galvanically or electrolytically zinc-coated steel sheet and soft aluminium surfacers.

Surfacers which have been fully puttied and then fine sanded with the following products: Raderal® IR Premium Putty Putty 2035.


Pre-treatment: Remove all grease, then lightly sand steel, galvanically / electrolytically zinc-coated steel sheet or soft aluminium.

Prior to pre-coating, clean all the substrates with Permacron® Silicone Remover 7010.

Application

Method of application Aerosol Can

Distance to object: 15 to 20cm

Spray nozzle:* wide can nozzle

No. of coats:

2-3 coats with intermediate flash-off time of approx. 5 minutes

Note: After use, hold aerosol upside down and spray briefly to clean nozzle.

4085a/02/04-UK

Drying

Air drying:


Recoating times: with surfacer after 10-15 minutes with waterborne after 20-30 minutes sandable: if required after 45-60 minutes

Further Treatment Re-coatable with:

Permasolid® HS Surfacer plus 5110 grey Permasolid® HS Express Surfacer 5250 Permasolid® SpectroFlex 5400 Permasolid HS Wet on Wet Surfacer 5330 Permahyd® Base Coat Series 280/285 in small areas

Special Notices 1. Do not recoat with polyester products.


3. Do not recoat with topcoat products as part of a compliant coating.

Dry sanding:


Wet sanding


Technical Data

VOC Content: The EU limit for this product (2004/42/IIB(e)(840) 840) in ready for use form is max. 840g/litre of VOC. The VOC content of this product in ready to use form is max. 840g/litre



4085a/02/04-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.2.19


Priomat® Wash Primer 4075 Priomat® Wash Primer 4075 is an acid-curing, two pack adhesion promoter based on polyvinyl butryl from our “PVB-System”. This data sheet specifies how this product is to be used in passenger car refinishing.

Priomat® Wash Primer 4075 promotes adhesion and serves to passivate metallic substrates, in particular aluminium. When used in combination with high-quality Permasolid® 2K acrylic surfaces and top coats from Spies Hecker, an optimum finish is achieved. This product also fulfils the warranty specifications of many car manufacturers.


4075/02/04-UK

Substrate

Suitable substrates: 1. Bare steel, sanded

2. Electroplated/roller galvanised steel panels or soft aluminium, cleaned and sanded

3. Lightly sanded factory primer


5. Surfaces treated with Raderal® 2K polyester products and then finely sanded

Pre-treatment: Steel, electroplated/roller galvanised steel panels or soft aluminium - degrease and sand lightly.

Factory primer - clean and sand lightly.

Original or old finish - clean and sand lightly, remove all traces of rust and sand the areas around the former rust spots to create a smooth transition to the old paintwork.

Before further treatment, clean all substrates once more with Permaloid® Silicone Remover 7010.

Application

Mixing ratio:

1:1 by volume with Priomat® Activator 4076.

Pot life: Ready for spraying approx. 8 hours @ 20 ºC. Mixed material must be used the dame day.

Reducer: Permacron® Reducer 3364 or 3380 if required up to a maximum of 10%.


Compliant HVLP


15-16 seconds

4075/02/04-UK


if required up to a maximum of 10%

Spray nozzle:* 1.3-1.4mm 1.3-1.6mm


manufacturer

No. of coats:

2-3

Flash-off: approx 5 minutes between coats.



8µm dry film thickness.

Drying

Air drying:


Recoating times: approx. 30 minutes

Re-coating: After flash-off at 20 °C recoat with: Permasolid® 2K surfacer

Special Notices 1. Any defects in the substrate can be repaired using Raderal® IR Premium Putty 2035.

2. With air drying, a minimum temperature of 15 ºC must be maintained.

3. Do not recoat with polyester or epoxy products

4. Not suitable for application on thermoplastic finishes.

5. Do not recoat directly with base coat or top coat. Use 2K surfacer prior to top coat application.

4075/02/04-UK



In order for the system to remain VOC compliant, additional reducer (above that shown in this TDS) should not be added in normal application.

Technical Data

Viscosity as supplied: at least 60 seconds.

Flash point: over 23 ºC

Solids content:

Wash Primer 4075 mixed with activator approx. 26.0% by weight approx. 15.84% by weightapprox. 14.0% by volume approx. 8.0% by volume

S.G: approx. 0.96 g/cm3 approx. 0.92 g/cm3

Coverage:* approx 10.0 m2/ltr at a dry film thickness of 8µm.

*The coverage has been calculated on the recommended dry film thickness and the percentage volume solids (without any additional reducer). No allowance was made for wastage during application.

VOC Content:* The EU limit for this product (2004/42/IIB(c)(780) 780) in ready for use form is max. 780g/litre of VOC. The VOC content of this product in ready to use form is max. 780g/litre





4075/02/04-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.2.20


Priomat® EP Primer Surfacer 4090 Stone Grey Priomat® EP Primer Surfacer 4090 stone grey is a zinc chromate-free, two pack primer surfacer from the Spies Hecker “2K-Epoxid-System”. This data sheet specifies how this product is to be used in passenger car refinishing.

Flexibility in use allows Priomat® Primer Surfacer 4090 stone grey to be used either as a wet-on-wet or as a sandable surfacer, and in two stage (direct recoat with topcoat or basecoat) or three stage (intermediate surfacer application over EP surfacer).


4090/10/04-UK

Important note: Major OEMs increasingly recommend the application of polyester putty not to bare steel, aluminium or galvanised steel but to a fully cured paint system. This avoids the possibility of corrosion between the polyester and the substrate. Suitable for application of polyester putty are OEM e-coat, OEM finish paint systems, fully cured 2K surfacers, clearcoats/topcoats and fully cured epoxy primer surfacer. We highly recommend that this procedure be followed when carrying out warranty repairs.

Substrate

Suitable substrates: 1. Bare steel, sanded

2. Electroplated/roller galvanised steel panels or soft aluminium, cleaned and sanded

3. Lightly sanded factory primer


5. UP-GF substrate, free of release agents, cleaned and sanded

Pre-treatment: Before further treatment, clean all substrates once more with Permaloid® Silicone Remover 7010.

This primer surfacer may not be applied on PVB (acid curing) primers.

Application 1. Medium build (with intermediate sanding).

Mixing Ratio:

2:1 by volume with Priomat® EP Hardener 3110.

Do not use any other Spies Hecker Hardener.

Pot Life: Ready for spraying approx. 8 hours at 20°C. Mixed material must be used the same day.

Reducer: Permacron® Reducer 3364 or 3380 up to a maximum of 15%.

4090/10/04-UK

Method of application Compliant HVLP


15-16 seconds

Reducer @ 20 °C: 10-15% up to a maximum of 15%



manufacturer

No. of coats:

2-3

Flash off: approx 5 minutes between coats

Recommended film thickness: Atomising pressure

60-90µm dry film thickness.

0.7 bar

Drying

Air drying: at 20°C ambient temperature sandable: overnight.

Forced drying: flash off time: approx. 10 minutes

drying time and temperature: 40-60 minutes @ 60 ºC metal temperature.

Application 2. Wet on Wet application

Mixing Ratio:

2:1 by volume with Priomat® EP Hardener 3110.

Do not use any other Spies Hecker Hardener.

Pot Life:

Ready for spraying approx. 8 hours at 20°C. Mixed material must be used the same day.

Reducer: Permacron® Reducer 3364 or 3380

4090/10/04-UK



15 - 16 seconds

Reducer @ 20 °C: 10-15% up to a maximum of 15%



manufacturer

No. of coats:

1-2

Recommended film thickness: Atomising pressure

25-50µm dry film thickness.

0.7 bar

Drying

Air drying: at 20°C ambient temperature sandable: overnight.

Wet-on-wet application: recoatable:

a) After 30 min. (max 8 hr) with Permasolid® Series 270

b) After 45-60 min. (max 8 hr) with Permahyd®

Basecoat Series 280/285.

4090/10/04-UK

Further treatment:

Dry sanding:

with random orbital sander and dust extraction, P400-500 grade.

Wet sanding:

with P600-800 grade.

Technical Data


Flash point: above 23 °C.

Solids content: Primer Surfacer 4090 mixed with hardener

approx. 73.8% by weight approx. 63.0% by weightapprox. 52.10% by volume approx. 40.9% by volume

S.G: approx. 1.57g/cm3 approx. 1.40g/cm3

Coverage:* approx. 10.2m2/ltr at a dry film thickness of 8µm.

*The coverage has been calculated on the recommended dry film thickness and the percentage volume solids (without any additional reducer). No allowance was made for wastage during application.

VOC Content:* The EU limit for this product (2004/42/IIB(c) (540)540) in ready for use form is max. 540g/litre of VOC. The VOC content of this product in ready to use form is max. 540g/litre


4090/10/04-UK

Special tips 1. Any defects in the substrate can be repaired using Raderal® Vario 2035 putty.

2. With air drying, a minimum temperature of 15 ºC must be maintained.

3. Not suitable for application on thermoplastic finishes.



In order for the system to remain VOC compliant, additional reducer (above that shown in this TDS) should not be added in normal application.

Storage



4090/10/04-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730

Spies Hecker. A member of DuPont Performance Coatings(UK) Limited.


2.2.21


Permasolid® HS Express Surfacer 5250 Permasolid® HS Express Surfacer 5250 is a high-grade, productive, VOC-compliant 2K HS sanding surfacer based on acrylic resins .

Very good application properties especially when applied with HVLP spray guns

Good levelling

Good vertical stability

Very good IR drying properties

Sandable after one hour air drying (with spot repairs & partial refinishes)

Good top coat flow


Substrate

Suitable substrates: 1. Steel, electroplated/roller galvanized steel or soft aluminium, cleaned, sanded and coated with Priomat® 1K Wash Primer 4085

2. Well sanded old or original paintwork (except thermoplastic paintwork)

3. Surfaces treated with Raderal® 2K polyester products and then finely sanded

4. UP-GF substrates, free of release agents, cleaned and sanded

Substrate pretreatment:

Carefully degrease and sand lightly.

Before further treatment, clean all substrates once more with Permaloid® Silicone Remover 7010

Special note: To guarantee optimum corrosion protection, we recommend coating any remaining rust spots on corners and edges, as well as on sanded through areas, with Priomat® 1K Wash Primer 4085.

Application

Mixing Ratio:

5:1 by volume with

Permasolid® HS Hardener 3307 extra fast Permasolid® HS Hardener 3310 Permasolid® HS Hardener 3315 slow

or

7:1 by volume with Permasolid® VHS Hardener 3220 fast Permasolid® VHS Hardener 3230 Permasolid® VHS Hardener 3240 slow

Elastification: See “Special notes“!

Reducer: Permacron® Reducer 3380 Permacron® Reducer 3364

Pot Life: Ready for spraying 45 – 60 minutes at +20°C

(depending on the hardener used).


Compliant HVLP


22-24 seconds 22-24 seconds


20% when mixed with Permasolid® HS hardener 30% when mixed with Permasolid® VHS hardener

Spray nozzle:* 1.5–1.6 mm 1.6–1.7 mm


manufacturer

Atomising pressure:* 0.7 bar

* see manufacturer‘s instructions!

No. of coats: 2–3 coats


70–200 µm depending on the spray nozzle

Drying

Air drying:

@ 20 ºC ambient temperature

Sandable: 70-130 µm 60-120 minutes (depending on the hardener used and on the dry film thickness)

130-200 µm overnight

Force Drying:

Flash-off: approx 5-10 minutes

Drying time and temperature:

60°C metal temperature

70-130 µm 20-25 minutes

130-200 µm 25-30 minutes


Infrared drying:

medium wave 10 minutes short wave 2 minutes half power 5 minutes full power

Recoating:

Dry sanding:

with random orbital sander and dust extraction P 400-500

Wet sanding:

sand with P 800-1000

Recoat with: Permasolid® HS Automotive Top Coat Series 270 Permahyd® Base Coat Series 280/285 and Permacron® / Permasolid® 2K clear coat

Special notes.

1. Elastification of rigid and semi-rigid types of plastic: First, add 15% Permasolid® Elastic Additive 9050 to the surfacer.

- then mix 3:1 with HS hardener + 10% reducer or - mix 4:1 with VHS hardener + 20% reducer

2. To facilitate sanding, apply a guide coat each time before sanding.

3. Any substrate defects can be treated with Raderal® putty. After drying and intermediate sanding, isolate putty spots with: Permasolid® HS Express Surfacer 5250.

4. When isolating certain spots – even on problem

substrates – the best results are achieved with a medium film thickness of 80-120 µm in 2 coats, after either air drying overnight or force drying/IR drying. With problem substrates, careful pre-treatment is imperative and the surfacer must be applied to the entire area.

Technical Data

Viscosity as supplied: thixotropic

Flash point: above +23 °C

S.G. Mixed 5:1 with HS Hardener 3310 & 20% Reducer 3380

approx. 0.97 g/cm3

Mixed 7:1 with VHS Hardener 3225 & 30% Reducer 3380

approx. 0.99 g/cm3

VOC Content:* The EU limit for this product (2004/42/IIB(c)(540) 540) in ready for use form is max. 540g/litre of VOC. The VOC content of this product in ready to use form is max. 540g /litre


Storage


Guaranteed shelf life: At least 24 months in sealed original containers






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.2.22


Permasolid® HS Wet-on-Wet Surfacer 5330. Permasolid® HS Wet-on-Wet Surfacer 5330 is a high-grade, VOC-compliant (VOC value <540 g/l) 2K HS wet-on-wet surfacer-based on acrylic resins.

Very good application properties·

Long pot life

Good levelling·

Fast application and recoating

Very good vertical stability

For professional use only!


Substrate

Suitable substrates: 1. Steel, electroplated/roller galvanized steel or soft aluminium, cleaned, sanded and coated with Priomat® Wash Primer 4075 or Priomat® 1K Wash Primer 4085.

2. OEM primer, finely sanded or unsanded and thoroughly cleaned.

3. Lightly sanded old or original paintwork (except TPA).


5. UP-GF substrates, free of release agents, cleaned and sanded.

Substrate pretreatment:

Clean all substrates carefully with Permaloid® Silicone Remover 7010

Sand lightly.

Clean all substrates once more with Permaloid® Silicone Remover 7010

Application Wet-on-wet application

Mixing Ratio:

5:1 by volume with Permasolid® VHS Hardener 3230 slow Permasolid® VHS Hardener 3240 extra slow

or

3:1 by volume with Permasolid® HS Hardener 3310 Permasolid® HS Hardener 3315 extra slow

Elastification: See “Special notes“!

Reducer: Permacron® Reducer 3364 Permacron® Reducer 3380 Permacron® Reducer 3365 slow

Pot Life: Ready for use 1.5 - 2 hours at +20°C(depending on hardener used)


Compliant HVLP


16-18 seconds DIN 4mm

16-18 seconds DIN 4mm


with VHS hardener: 30% with HS hardener: 20%

Spray nozzle:* 1.2-1.4 mm 1.3-1.5 mm


manufacturer

Atomising pressure:* 0.7 bar

* see manufacturer‘s instructions!

No. of coats:

1-2 coats


wet-on-wet application 25–30 µm dry film thickness

Recoating Permasolid® HS Automotive Top Coat Series 270/275·Permahyd® Base Coat Series 280/285 and Permasolid® 2K clear coat

Special notes. Elastification of rigid and semi-rigid types of plastic:

First, add 30% of Permasolid® Elastic Additive 9050 to the surfacer.

mixed with HS hardener - 2:1 with 20% reducer mixed with VHS hardener - 3:1 with 20% reducer

Important note: The elastified surfacer must be allowed to flash-off 30-45 minutes before base coat / top coat application.

Technical Data


Flash point: above +23 °C

Solids content: Surfacer 5330 mixed 5:1 VHS Hardener 3225 & 30 % Reducer 3380

Surfacer 5330 mixed 3:1 HS Hardener 3310 & 20 % Reducer 3380

61.4 % by weight 39.7 % by volume


S.G. 1.36 g/cm³ 1.36 g/cm³ VOC Content:* The EU limit for this product (2004/42/IIB(c)(540) 540)

in ready for use form is max. 540g/litre of VOC. The VOC content of this product in ready to use form is max. 540g /litre


Coverage:* 13.2 m²/l 30 µm dry film thickness

12.9 m²/l 30 µm dry film thickness

*The coverage was calculated on the basis of the recommended dry film thickness and the solids content by volume (ready for use). No allowance was made for wastage during application.

Storage


Guaranteed shelf life: At least 24 months in sealed original containers






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.2.23


Permasolid® HS Vario Surfacer 8590

Permasolid® HS Vario Surfacer 8590 is a high-grade, versatile VOC-compliant (VOC content <540g/l) 2K HS surfacer based on acrylic resins.

Can be used as a sanding surfacer and as a non-sanding surfacer.·

can be mixed with Permasolid® HS/VHS hardeners·

Good isolating properties even on old thermoplastic paintwork·

Very good top coat flow


8590/08/2006-UK

Substrate Suitable substrates: 1. Steel, electroplated/roller galvanized steel or

soft aluminium, cleaned, sanded and coated with Priomat® Wash Primer 4075, Priomat® 1K Wash Primer 4085.

2. OEM primer, finely sanded or unsanded and thoroughly cleaned

3. Lightly sanded old or original paintwork (including thermoplastic paintwork)


5. UP-GF substrates, free of release agents, cleaned and sanded.


Carefully clean with Permaloid® Silicone Remover 7010

Sand lightly.

Clean once more with Permaloid® Silicone Remover 7010.

Application

As a sanding surfacer:

5:1 by volume with

Permasolid® VHS Hardener 3230 Permasolid® VHS Hardener 3240 slow

3:1 by volume with

Permasolid® HS Hardener 3310 Permasolid® HS Hardener 3315 slow

8590/08/2006-UK

Elastification: See "Special notes"!

Pot Life: Ready for use 30-60 minutes at +20°C.(depending on hardener used)

Reducer: Permacron® MS Dura Plus 8580 Permacron® Reducer 3364 Permacron® Reducer 3380 Permacron® Reducer 3365 slow


Compliant HVLP

Gravity feed Gravity feed


DIN 4 mm = 20 - 25 seconds


HS hardener: 10 - 15 %VHS hardener: 10 - 20 %

Spray nozzle: 1.4-1.8 mm 1.6-1.9 mm

Spray pressure: 1.5-3.0 bar

Atomising pressure - 0.7 bar

No. of coats: 2 coats = 50 - 80 µm dry film thickness 3 coats = 100 - 120 µm dry film thickness


50–120 µm dry film thickness

8590/08/2006-UK

Drying

Sanding surfacer: Normal and medium film thickness

Air drying:

at 20 °C ambient temperature Dry for sanding:overnight

Force drying:

Flash-off time:approx 5-10 minutes

Drying time at +60°C metal temperature: up to 80 µm: 20-30 minutes above 80 µm: 40-50 minutes

Infrared drying:

Flash-off time: approx: 5-10 minutes

Drying time (depending on film thickness):

medium wave; 10-20 minutes short wave; 10 minutes

Further steps

Dry sanding:

With random orbital sander and dust extraction P 400-500

Wet sanding:

With P 800-1000

Recoating (sanding surfacer):

Recoat with: Permasolid® HS Automotive Top Coat Series 270 Permahyd® Base Coat Series 280/285 and Permasolid® 2K HS clear coat

8590/08/2006-UK

Application

as non-sanding surfacer.

Mixing ratio:

5:1 by volume with

Permasolid® VHS Hardener 3230 Permasolid® VHS Hardener 3240 slow

3:1 by volume with

Permasolid® HS Hardener 3310 Permasolid® HS Hardener 3315 extra slow

Pot life: Ready for use 30-60 minutes at +20°C.(depending on hardener used)

Reducer: Permacron® MS Dura Plus 8580 Permacron® Reducer 3364 Permacron® Reducer 3380 Permacron® Reducer 3365 slow


Compliant HVLP

Gravity feed Gravity feed


DIN 4 mm = 16 - 18 seconds


HS hardener: 20 - 25 %VHS hardener: 30%

Spray nozzle:* 1.2-1.4 mm 1.3-1.5 mm

Spray pressure:* 2.0-2.5 bar -

Atomising pressure - 0.7 bar

No. of coats: 1 - 2 coats

8590/08/2006-UK


25–30 µm dry film thickness

Wet-on-wet application.

Flash-off time before top coat at +20°C ambient temperature:

15 - 20 minutes up to 90 minutes with Permasolid® HS Automotive Top Coat Series 270

25 - 30 minutes up to 90 minutes with: Permahyd® Base Coat Series 280/285

Recoating (non-sanding surfacer):


Special notes

1. Elastification of rigid and semi rigid types of plastic:15% Permasolid® Elastic Additive 9050 must first be added to the surfacer. • mixed with VHS hardener - 3:1 with 20% reducer·• mixed with HS hardeners - 2:1 with 20% reducer

Important note: The elastified surfacer must be allowed to flash-off 30-40 minutes before base coat/top coat application.

2. To facilitate sanding, apply Permaloid® Control Paint black 7878 each time before sanding. Do not spray onto wet surfacer.

3. Any substrate defects can be treated with Raderal® putty. After drying and intermediate sanding, isolate putty spots with Permasolid® HS Vario Surfacer 8590.

4. To achieve the perfect finish on passenger cars, we recommend sanding the surfacer after it has been left to dry overnight.

5. Do not apply wet-on-wet on top of thermoplastic factory finish and if possible sand after overnight drying.

6. For air drying we recommend a minimum temperature of +15°C.

8590/08/2006-UK

Data

(sanding surfacer):


Flash point: above +23°C

HS Vario Surfacer 8590 HS Vario Surfacer 8590

3:1 with HS Hardener 3310

15 % Reducer 3380

5:1 with VHS Hardener 3230

20 % Reducer 3380

Solids content: 60.9 % by weight

39.9% by volume

63.1 % by weight

41.9 % by volume

Specific weight: 1.34 g/cm³ 1.37 g/cm³

Coverage: at 30 µm dry film thickness

13.3 m²/l 14.0 m²/l

VOC value: The EU limit for this product (2004/42/IIB(c)(540) 540) in ready for use form is max. 540g/litre of VOC. The VOC content of this product in ready to use form is max. 540g /litre

Data

(non-sanding surfacer):

HS Vario Surfacer 8590 3:1 with HS Hardener

3310 25% Reducer 3380

HS Vario Surfacer 8590 5:1 with VHS Hardener

3230 30 % Reducer 3380

Solids content: 57.8 % by weight 36.7 % by volume


Specific weight: 1.30 g/cm³ 1.32 g/cm³

Coverage: at 30 µm dry film thickness

12.3 m²/l 12.9 m²/l

VOC value: The EU limit for this product (2004/42/IIB(c)(540) 540) in ready for use form is max. 540g/litre of VOC. The VOC content of this product in ready to use form is max. 540g /litre

8590/08/2006-UK

Storage

Guaranteed shelf life: 24 months in sealed original containers






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730


2.3.4


Raderal® IR Premium Putty 2035 Raderal® IR Premium Putty 2035 is a universal putty from our 2K-Polyester-System. It is particularly suitable for galvanised substrates on passenger cars. This putty is easy to apply, has good sanding properties and high vertical stability, and can be dried with short and medium-wave infrared. It is suitable for use both as a body filler and as a fine putty.


2035/02/03-UK

Substrate

Suitable substrates: Steel Aluminium Galvanised steel sheet Glass fibre reinforced plastics (UP-GF) Old or OEM finish Fully cured 2K Surfacer/2K Primer

Special Note: This putty may not be applied on polyvinylbutyral (PVB) (acid curing) primers or 1K primers (e.g. nitrocellulose or synthetic resin). It is also unsuitable for thermoplastic or viscoplastic paintwork. In these cases the paint surface should be sanded to bare metal and the putty applied within this area.

Substrate Pre-treatment:

Degrease carefully and sand lightly.

with GRP substrates: - remove all releasing agent residues, sand lightly.

Before further treatment, clean once more with Permaloid® Silicone Remover 7010.

Application

Method of application:

With a putty knife or plastic spreader.

Mixing ratio:

Add 2-3% by weight Raderal® Hardener 0909

Special Note: Avoid adding excessive Hardener as this can lead to bleeding through, in particular with light metallic colours.

Pot-life: 3 to 5 minutes at 20 ºC.

2035/02/03-UK

Drying

Air drying:


Infra-red Drying:

Medium wave 5 minutes Short wave 3 minutes (at 50% power)

Sanding:

Following the above mentioned drying time

a) as body filler

First sanding: dry with P 80 grit paper Second sanding: dry with P 120-240 grit paper

b) as fine putty:

First sanding: dry with P 120 grit paper Final sanding: dry with P280 grit paper

Heat resistance: Up to 80 ºC for all other substrates.

Recoating: 1. Apply Vario Putty 2035 again as a fine putty

2. Prime bare patches and patches of putty with Priomat® Primer 3255 red brown, Priomat® 1K Wash Primer 4085 or Priomat® Wash Primer 4075

3. Surfacer* Permasolid® HS Surfacer *Before surfacer application the entire area must be dry sanded with P 280-320 grit paper.

2035/02/03-UK

Technical Data

Viscosity as supplied: Paste

Flashpoint:


Putty: above 23 ºC Hardener: N/A

85.98% 1.83g/cm3

VOC Content: The EU limit for this product (2004/42/IIB(b)(250) 250) in ready for use form is max. 250g/litre of VOC. The VOC content of this product in ready to use form is max. 250g/litre

Storage

Storage temperature approx +20 ºC. (+30 ºC must not be exceeded).


2035/02/03-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.4.1


Priomat® Pore Filler 3311 Priomat® Pore Filler 3311 is a special fine putty for filling small pores in the surface of plastic parts on cars.

It ensures a very smooth surface and a perfect finish.


3311/10/99-UK

Substrate

Polyurethane plastic parts with pores in the surface (flexible PUR)

Preparation of substrate:

Clean plastic surface thoroughly In the case of flexible PUR: wash down five times with Permaloid® Silicone Remover 7010 each time using fresh material applied with a brush (ensure release agent is completely removed). Allow the reducer to evaporate (e.g. 1 hour at 40 ºC or air dry overnight). Clean once again with Permaloid® Silicone Remover 7010.

Application

Method of application: Apply with a lint free cloth and wipe into the pores.

Mixing ratio: Ready for use

Drying

Air drying:

at 20°C approx. 5 mins.

Further steps Wipe off the surplus Priomat® Pore Filler 3311 with a cloth. (Thereafter do not clean again or wipe with damp cloth).

Prime flexible PUR with: Permacron® 1:1 Elastic Primer Surfacer 3300 / 3301

Recoat with:

a) Permahyd® Base Coat Series 280/285 (without elastic additive) + plasticized Permasolid®

HS 8030, HS 8035, HS 8600

b) Plasticised Permasolid® Topcoat Series 270

3311/10/99-UK

Storage



Guaranteed shelf life: Solids content:

S.G.

At least 24 months in original sealed containers.

75.5%

1.69g/cm3

VOC Content: This product is out of scope of the EU VOC Directive.

3311/10/99-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.4.8


Permacron® 1:1 Elastic Primer Surfacer 3300 Black Permacron® 1:1 Elastic Primer Surfacer 3300 is a universal two component primer surfacer for all usual plastics on vehicle exteriors. This primer surfacer can be used in an efficient two-stage system, as direct recoating with an elastified top coat is possible. It is characterised by excellent adhesion, high elasticity and easy application.


3300/10/99-UK

Substrate

Suitable substrates: All normal external plastic parts on motor vehicles (PP, EPDM, ABS, PC, PPD, PBTP, PA, GRP, R-TRU, PUR, PUR Soft).

Pre-treatment: The substrate must be free of all traces of release agent.

Soak a piece of clean lint free cloth in Permaloid®

Silicone Remover 7010, wipe over surface to be painted and wipe off whilst wet with another clean lint free cloth. Repeat as necessary until surface is thoroughly clean.

The amount of work involved in the cleaning will depend on how much releasing agent is still adhering to the plastic or residing in its pores.

To enhance the cleaning effect we recommend using a sanding pad (3M 7448).

Allow the reducer to evaporate thoroughly (e.g. air drying overnight at ambient temperature or temper for 30 - 40 minutes at 40 ºC).

Prior to priming clean lightly once more with Permaloid® Silicone Remover 7010 (antistatic effect). Ensure surface is clean and dry before priming.


Application

Mixing ratio: 1:1 by volume only with Permacron® Elastic Hardener 3301

Pot life: ready for spraying - approx. 8 hours at +20 ºC.

3300/10/99-UK



16 - 18 seconds


None (ready for spraying with hardener only)



manufacturer

No. of coats:

1 light coat allow 5 mins flash off followed by one full coat



approx. 15-20 µm dry film thickness.

NB. On PUR Softfoam.

If there are pores in the soft foam surface, these can be filled using Priomat® Pore Filler 3311. Over this apply Permacron® 1:1 Elastic Primer Surfacer 3300 Beige / Black.

Drying

At +20 ºC ambient temperature

After 15 - 20 min. (max 24 hours) recoatable wet-on-wet with a suitable top coat, as shown below.

If required Permacron® Elastic Primer Surfacer 3300 can be sanded lightly with wet sanding paper grit P 600 - 800 after:

30 min. low baking at 60 ºC metal temperature or 2 hours air drying at +20 ºC ambient temperature

If sanding and before recoating, clean with Permaloid®

Silicone Remover 7010 or Permahyd® Silicone Remover 7080.

3300/10/99-UK

Recoating with: Permahyd® Basecoat Series 280/285+ Permasolid® 2K Clear Coats or Permasolid® HS Automotive Topcoat Series 270 (for elasticification of HS Topcoat Series 270 and HS Clear Coats: See System Data Sheet Permacron®

Elastic Additive 9050. Note: Plastic parts must not be pressure jet cleaned within the first six weeks of painting. After this time a distance of not less than 30 cm must be maintained between the nozzle and object.

Technical Data

Viscosity as supplied: 1:1 Elastic Primer Surfacer 3300 -approx. 100 sec. (DIN 53211)

Flash point: 1:1 Elastic Primer Surfacer 3300 - over 23 ºC

Elastic Hardener 3301 - over 23 ºC

Solids content:

Primer Surfacer 3300 approx. 54.0% by weight

mixed approx. 35.7% by weight

(without reducer) Approx. 37.0% by volume approx. 23.5% by volume

S.G: approx. 1.20 g/cm3 approx. 1.04 g/cm3

Coverage:* approx. 8.2 m2/l at film thickness of 15 - 20 µm

* The coverage has been calculated on the basis of the recommended dry film thickness and the solid content by volume (without reducer). No allowance has been made for wastage during application.



3300/10/99-UK

Special Notes Extra care should be observed when masking as Permacron® Elastic Surfacer 3300 is pigmented.



Storage

All paint products must be stored in dry conditions within the temperature range of 5-20 ºC.


Protect from frost


3300/10/99-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.4.9


Permasolid® Elastic Additive 9050 Permasolid® Elastic Additive 9050 is a special additive based on highly elastic polyurethane resins.

It is used to adjust:

Permasolid® 2K automotive top coats Permasolid® 2K clear coats Permasolid® 2K acrylic surfacers to the elasticity required for painting plastic parts.

Permasolid® Elastic Additive gives the paint system a lasting, high degree of elasticity.



9050/10/99-UK

Application

Mixing ratio:

For all commonly found types of plastic, an addition of 30% Permasolid® Elastic Additive 9050 is required. Not necessary for UP-GF.

The base material should first be mixed with the Elastic Additive, before any addition of hardener.

Note: Elasticised 2K acrylic surfacer must always be mixed 2:1 by volume.

Application Viscosity

If necessary, use Permacron® Reducer 3364/3380 or Permacron® MS Dura plus 8580 to adjust the crosslinked mixture to the spray viscosity given in the respective Technical Data Sheets.

Technical Data


76.97% 1.05g/cm3



Special Notes Do not use in: Permahyd® products

Storage




9050/10/99-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.4.10


Permasolid® Textured Additive SA 101 Coarse Permasolid® Texture Additive SA 101 coarse is an additive for: Permasolid® HS Automotive Top Coat Series 270 and can be used to convert this into textured top coats.

This textured top coat can be used for painting plastic parts of vehicles and for producing textured finishes in general.


For professional use only! VR Technical Data Sheet No. SA101/10/99-UK

SA101/10/99-UK

Substrate

Suitable substrates: Plastic parts which have been primed and filled

Old paintwork (on plastic parts of steel e.g. door sills, front parts)

Pre-treatment: For plastic parts, see System Data Sheet.

Old paintwork must be sanded and cleaned with Permaloid® Silicone Remover 7010.

Application

Mixing ratio: 1:1 by volume with Permasolid® HS Automotive Top Coat series 270. Then mix this 3:1 by volume with a suitable Permasolid® Top Coat Hardener.

Pot life: Ready for spraying approx. 90 minutes @ 20 °C



mixing viscosity



manufacturer

No. of coats:

For plastic parts, see System Data Sheet

Flash-off: approx. 10 - 20 minutes at +20 ºC

SA101/10/99-UK

Drying

Air drying:

at 20 ºC ambient temperature dust dry: 40-50 minutes dry for assembly: 4-6 hours dry: overnight

Force Drying: 45 mins at 60°C metal temperature

Storage



Protect from frost



45.06% 1.01g/cm3



Special Notes

1. It is not necessary to add Permasolid® Elastic Additive 9050 when using SA101.

2. Permasolid® Texture Additive SA 101 coarse is only suitable for use on add-on parts (e.g. bumpers, spoilers).

3. Permasolid® Texture Additive SA101 coarse is thixotropic and becomes liquid after stirring.

4. Do not place on mixing machine. Hand stir only. It is important to bring products to room

temperature (18 - 20 ºC) before mixing and use. Optimum application results will be obtained by

ensuring this procedure is followed. In order for the system to remain VOC compliant,

additional reducer should not be added in normal application.

SA101/10/99-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.4.11


Permasolid® Textured Additive SA 102 Fine Permasolid® Texture Additive SA 102 fine is an additive for: Permasolid® HS Automotive Top Coat Series 270 and can be used to convert this into textured top coats.




For professional use only! VR Technical Data Sheet No. SA102/10/99-UK

SA102/10/99-UK

Substrate

Suitable substrates: Plastic parts which have been primed and filled

Old paintwork (on plastic parts of steel e.g. door sills, front parts)

Pre-treatment: For plastic parts, see System Data Sheet.

Old paintwork must be sanded and cleaned with Permaloid® Silicone Remover 7010.

Application

Mixing ratio: 1:1 by volume with Permasolid® HS Automotive Top Coat series 270. Then mix this 3:1 by volume with a suitable Permasolid® Top Coat Hardener.




mixing viscosity



manufacturer

No. of coats:

For plastic parts, see System Data Sheet


SA102/10/99-UK

Drying

Air drying:



Storage



Protect from frost



49.64% 1.02g/cm3



Special Notes

1. It is not necessary to add Permasolid® Elastic Additive 9050 when using SA102.

2. Permasolid® Texture Additive SA 102 fine is only suitable for use on add-on parts (e.g. bumpers, spoilers).

3. Permasolid® Texture Additive SA101 coarse is thixotropic and becomes liquid after stirring.

4. Do not place on mixing machine. Hand stir only. It is important to bring products to room

temperature (18 - 20 ºC) before mixing and use. Optimum application results will be obtained by

ensuring this procedure is followed. In order for the system to remain VOC compliant,

additional reducer should not be added in normal application.

SA102/10/99-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.4.12


Permasolid® Matting Additive MA 100 Permasolid® Matting Additive MA 100 is an additive for:

Permasolid® HS Automotive Top Coat Series 270 and provides a matt effect.

Permasolid® MA 100 gives the top coat a satin gloss and is suitable for painting plastic parts on vehicles as well as for creating satin gloss finishes in general.


For professional use only! VR Technical Data Sheet No. MA100/10/99-UK

MA100/10/99-UK

Substrate

Suitable substrates: 1. Plastic parts which have been primed and filled

2. Old paintwork (on plastic parts or steel e.g. door sills, and front parts)

Pre-treatment: For plastic parts, see Plastic System Data Sheet. Old paintwork must be sanded and cleaned with Permaloid® Silicone Remover 7010.

Application

Mixing ratio: 1:1 by volume with Permasolid® HS Automotive Top Coat Series 270. Then mix this 3:1 by volume with a suitable Permasolid® HS top coat hardener,


MA100/10/99-UK



mixing viscosity



manufacturer

No. of coats:

1.5 coats = 50-60µm with Permasolid® HS Automotive Top Coat Series 270


Drying

Air drying:



Storage



Protect from frost



50% 1.13g/cm3



MA100/10/99-UK

Special Notes

1. It is not necessary to add Permasolid® Elastic Additive 9050 when using MA100.

2. Permasolid® Matting Additve MA 100 is not suitable for matting clear coats - use Permacron® Satin Gloss 8070 Clear Coat.

3. The actual gloss level produced also depends on the hardener used, the film thickness and the drying method. Hardeners with higher solid content, high film thicknesses or low baking always result in a slightly higher gloss level.

4. Permasolid® Matting Additive MA100 is thixotropic and becomes liquid after stirring.



MA100/10/99-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.4.13


Permacron® Elastic Primer 3410 Transparent Silver Permacron® Elastic Primer 3410 transparent silver is a versatile one-pack adhesion promoter for the majority of plastic parts commonly found on vehicle exteriors.

This primer is characterised by excellent adhesion, high elasticity and easy application.

Available in “Spray Max” aerosol cans, this product is suitable for fast and convenient application.


3410/02/04-UK

Substrate

Suitable substrates: All plastic parts commonly found on vehicle exteriors (PP, EDPM, ABS, PC, PPO, PA, R-TPU, PBTP, PVC, PUR, flexible foam, UP-GF

Pre-treatment: The substrate must be free of release agents.

Before cleaning plastic parts, heat them for 60 minutes at 60°C to let the release agents exude.

Clean with Permaloid® Silicone Remover® 7010. The extent of the cleaning required depends on the type and quantity of release agents present. We recommend the use of and abrasive pad (3M 7448) to assist in the cleaning process. Allow the cleaning fluid to evaporate completely (e.g. air dry overnight at ambient temperature or low bake for 30-40 minutes at 60°C).

Before applying the primer, clean lightly once more with Permaloid® Silicone Remover 7010,(antistatic effect).

Application

Use: Shake spray can well for at least 2 minutes.

Spray can distance: Spray at a distance of 20-25 cm


Number of coats: 1 full coat = 1-2µm

Flash-off time: 10-15 minutes at 20 °C ambient temperature

3410/02/04-UK

Further treatment

Surfacer: Permasolid® 2K Surfacer


For elastication of the products: see System Data Sheet “The Paint System for Plastic Parts”.

Storage


Storage conditions:

Storage between 20-25 °C


3.56% 0.75g/cm3



Special Notes

It is important to bring products to room temperature (18-20 ºC) before mixing and use.



3410/02/04-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.6.4


Permaloid® Silicone Remover 7010 Permaloid® Silicone Remover is a universal product specially designed to remove contaminants and release agents on all metals and plastics prior to painting. It displays an anti-static characteristic which will lessen dust and dirt attraction to the component.


7010/10/99-UK

Substrate

Suitable substrates: Old paintwork, sanded or fresh paintwork, bare metal and all Priomat® and Raderal® products. It is also suitable as an antistatic effect cleaner for all normal external plastic parts on motor vehicles (PP, EPDM, ABS, PC, PPD, PBTP, PA, GRP, R-TRU, PUR, PUR Soft).

Pre-treatment of plastic substrates:

The substrate must be free of all traces of release agent.

Soak a piece of clean lint free cloth in 7010, wipe over surface to be painted and wipe off whilst wet with another clean lint free cloth. Repeat as necessary until surface is thoroughly clean.

The amount of work involved in the cleaning will depend on how much releasing agent is still adhering to the plastic or residing in its pores. To enhance the cleaning effect we recommend using a sanding pad (3M 7448). Allow the reducer to evaporate thoroughly (e.g. air drying overnight at ambient temperature or temper for 30 - 40 minutes at 40 ºC).

In the case of PUR softfoam however, warm the part for 60 mins at 40 ºC prior to cleaning to allow the release agent to sweat. Then clean 5 times using fresh Permaloid® Silicone Remover 7010. Allow the Remover to evaporate thoroughly. (e.g. air dry at room temperature or warm for 30 - 40 minutes at 40 ºC).

Prior to priming clean lightly once more with Permaloid® Silicone Remover 7010 (antistatic effect). Ensure surface is clean and dry before priming.

Special Hints

1.) On previously painted surfaces do not over saturate as this may cause the surface to soften.

2.) Use only clean lint free cloths.

7010/10/99-UK

Storage


Storage conditions:

All paint products must be stored in dry conditions within the temperature range 5 ºC to 20 ºC


Protect from frost

S.G: 0.76g/cm3

VOC Content:* The EU limit for this product (2004/42/IIB(a)(850) 850) in ready for use form is max. 850g/litre of VOC. The VOC content of this product in ready to use form is max. 850g/litre


7010/10/99-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.6.8


Permahyd® Silicone Remover 7080 Permahyd® Silicone Remover 7080 is a specifically designed low VOC product to remove surface contaminants prior to application of Permahyd®. Heavily contaminated surfaces must first be cleaned using Permaloid® Silicone Remover 7010.


7080/10/99-UK

Use

As silicone remover: Principally for cleaning coated surfaces with a primer or surfacer before they are treated further.

Application

Apply Permahyd® Silicone Remover 7080 onto the surface and remove with a dry cloth.

Allow cleaned surfaces to dry completely or blow dry before recoating.

Notes Do not allow the silicone remover to dry on the surface. Always use a clean cloth. Heavily soiled parts must be cleaned twice. This product is not suitable for removing release agent residues form UP-GF or other plastic materials.

Technical Data:

S.G: 0.97 g/cm3

VOC Content: The EU limit for this product (2004/42/IIB(a)(200) 200) in ready for use form is max. 200g/litre of VOC. The VOC content of this product in ready to use form is max. 200g/litre


Storage


7080/10/99-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.6.9


Permacron® Blend-in additive 1035 Permacron® Blend-in additive 1035 is a specially prepared mixture of solvents and other components designed to allow simple and effective spot repairs of 2K topcoats and Clear Coats.


1035/01/02-UK

Field of Application The Permacron® Blend-in additive 1035 was developed to guarantee easy blending-in of 2K HS clear coats and top coats.

An invisible transition can be achieved by means of this special product. It offers excellent polishing properties and outstanding finish.

Preparation work according to the Spies Hecker paint systems. Make sure to keep the surfacer area as small as possible.

Blend-in system for 2K clear coats

Mixing ratio:

Permasolid® 2K clear coat 2:1 or 3:1 depending on which clear coat is used by volume with Permasolid® hardener

Application viscosity @ 4mm, 20 ºC, DIN 53211:

16-17 seconds

Reducer @ 20° material temperature:

0-15%

Coating: Recoat until basecoat area is fully covered (overlapping coats).

Blending-in: Melt overspray area with blend-in additive only.

Blend-in system for 2K top coats

Mixing ratio: Permasolid® HS Automotive Top Coat Series 270

2:1 by volume with Permasolid® hardener

Application viscosity @ 4mm, 20 ºC, DIN 53211:

16-17 seconds

1035/01/02-UK

Application

Reducer @ 20° material temperature:

0-15%

Coating: Recoat until basecoat area is fully covered (overlapping coats).

Blending-in: Melt overspray area with blend-in additive only.

Note: After the required drying time allow to cool for a minimum of 1 hour before polishing with a fine polishing paste either by hand or by machine at low speed.

SG: approx. 0.91 g/cm3



Storage


1035/01/02-UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.6.11


Permahyd® Stone Chip Protector 7100–7103. Permahyd® Stone Chip Protector is a waterborne product which protects the substrate from damage caused by impact from stone chips.

• It is highly elastic

• Can be recoated with all top coats

• Available in different colours·

• It is especially suitable for those areas on passenger cars and commercial vehicles which are exposed to impact from stone chips, such as front parts and door sills.

For professional use only! VR Technical Data Sheet No. 7100_7103/07/2006 - UK

7100-7103/07/2006 - UK

Substrate

Suitable base coats: 1. Well sanded old or original finish

2. Surfaces coated with a primer or surfacer

Important Note: Permahyd® Stone Chip Protector may not be applied on PVB (acid curing) primers.

Pretreatment:

Clean all substrates carefully with Permaloid® Silicone Remover 7010.

Sand lightly.

Clean all substrates once more with Permaloid® Silicone Remover 7010.

Application

Spray gun:

Underbody spray gun with screw thread for disposable tins.

if a finer texture is desired, Stone Chip Protector can be applied with a gravity feed when mixed with the appropriate amount of reducer.

Reducer: Permahyd® Demineralised Water 6000 (in accordance with ISO 3696)

7100-7103/07/2006 - UK

High pressure spraying



Viscosity as supplied depends on quantity of reducer added


_ up to 10 %

Spray nozzle:* _ -1.5 - 2.0 mm

Spray pressure:* 3 -4 bar 45 - 60 psi

For recommended spraying pressure refer to spraygun manufacturer

No. of coats:

2 to 3 coats


150-300 µm

Drying

Air drying:

at +20 ºC ambient temperature

up to 150 µm 2–2.5 hours up to 300 µm overnight

Force drying:

Flash-off time: 35–40 minutes

Drying time at +60°C metal temperature:

150-300 µm 30 minutes

Recoating: Permasolid® HS Automotive Top Coat Series 270 Permahyd® Base Coat Series 280/285 and Permasolid® 2K clear coat

7100-7103/07/2006 - UK

Technical Data


Flash point: non-flammable

Solids content:

64.9 % by weight

51.9 % by volume

S.G. 1.36 g/cm³

Coverage*: 3.3 m²/l

* The coverage was calculated on the basis of the recommended dry film thickness and the solids content by volume (without reducer). No allowance was made for wastage during application.



Storage

Storage temperature between +20 ºC.

(not below +5 ºC)


7100-7103/07/2006 - UK






Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730



2.6.12


Permahyd® Blend-In Additive 9005 new Permahyd® Blend-In Additive 9005 new helps to achieve an invisible blend with Permahyd® base coat series 280/285. With critical colours it prevents colours changes in the blend-in area.


9005/11/2006-UK

Substrate

Suitable substrates: 1. Fully cured, solvent resistant well preserved and lightly sanded original or old paintwork.

2. Surfaces coated with a primer or a surfacer.

Suitable priming materials: Depends on the object and on the substrate, in accordance with our system recommendation.


Thoroughly clean original or old finish and surfacer with Permaloid® silicone remover.

Dry sand with random orbital sander and dust extraction P400–500 or wet sand with P 800.

Lightly sand blend-in area of the undamaged original finish with P 1000-1200 grade, or e.g. with 3M Scotch Brite ultra fine. Clean all substrates with Permaloid® silicone remover.

Thoroughly clean the lightly sanded substrates once more with Permahyd® Silicone Remover before recoating.

Application

Reducer: Not necessary.



Ready to spray

Spray nozzle:* 1.2-1.3 mm WSB / 1.3 mm

Spray pressure:* 2.0-2.5 bar -

Atomising pressure: - 0.7 bar

9005/11/2006-UK

Blend-in system:

Depending on the colour and hiding power, apply 3 - 5 light/dry coats of ready-to-use Permahyd® Base Coat Series 280/285 with reduced pressure (0.8 - 1.5 bar)** to the area to be repaired.

** Regardless of the manufacturer’s recommendation, the input pressure should be reduced as indicated for this blend-in system.

Allow each coat to flash-off until matt. Matting can be accelerated by blowing off.

Then, mix ready-to-use base coat 1:1 with Blend-In Additive 9005 new.

Depending on the colour, apply 2 - 3 light coats of the 1:1 blend-in mixture to adjust the effect. Blend-in the fade-out area using reduced pressure (0.8 - 1.5 bar).**

** Regardless of the manufacturer’s recommendation, the input pressure should be reduced as indicated for this blend-in system.

Flash-off:

15-20 minutes at +20°C (before clear coat)

Ways to reduce flash-off times*:

Surface matting can be accelerated by blowing of with an air diffuser (hand-held or stationary device).

It is possible to blow of with the spray gun after waiting at least 5 minutes.

Drying

Air drying:

5 minutes

Recoating: Permasolid® 2K clear coat

Special Note Do not apply this product in its pure form.

9005/11/2006-UK

Technical Data

Viscosity as supplied: 56-65 seconds (ISO 4 mm)

Flash point: above +60°C

Solids content:


S.G: 1.01 g/cm³

VOC Content: This product is out of scope of the EU VOC Directive


Storage

Frost-free!

Store between +5°C and +35°C


9005/11/2006-UK





Spies Hecker Wedgewood Way Stevenage Hertfordshire SG1 4QN

Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730

Spies Hecker. A member of DuPont Performance Coatings.


2.6.13


Permacron® Speed Blender 1036 The Permacron® Blend-In Additive 1036 was developed to guarantee easy blending-in of 2K clear coats and top coats.

• easy to use (in its pure form)·

• good wetting on all substrates·

• very fine fade-out on to original substrate


1036/11/2006-UK

Substrate

Base coat application: Keep the surfacer area as small as possible. Recoat until surfacer area is fully covered (overlapping coats)

Blend-in system for 2K clear coats

Mixing ratio:

Permasolid® 2K clear coat

Mix according to Technical Data Sheet of clear coat

Coating:

Recoat Permahyd® Base Coat Series 280/285 with clear coat ready-to-spray (overlapping coats).

Apply Permacron® Speed Blender 1036 in its pure form to the blend-in area within the sanded area.

Blend-in system for 2K top coats

Mixing ratio:

Mix according to Technical Data Sheet of top coat Permasolid® HS Automotive Top Coat Series 270.

Recoat until surfacer area is fully covered (overlapping coats)

Coating:

Apply Permacron® Speed Blender 1036 in its pure form to the blend-in area within the sanded area.

Polishing the blend-in areas

Air drying:

Polishing the blend-in areas at +20°C ambient temperature:

overnight

Force drying:

Flash-off time:

Drying time

5-10 minutes

30 minutes @ 60OC object temperature

1036/11/2006-UK

Polishing the blend-in areas at +20°C ambient temperature

after 1 hour

Infrared drying:


Short wave: 10 minutes

Polishing the blend-in areas at +20°C ambient temperature

after 1 hour

Polish the blend-in area with fine polishing paste (e.g. Perfect-it™ III Extra Fine Compound 80349) manually or by polishing machine (e.g. Perfect-it™ III Compound 09550).

Finally, polish with high-gloss polish (e.g. 3M).

Technical Data

Viscosity as supplied: 11 seconds (DIN 4mm)

Flash point: +20°C

S.G: 0.93 g/cm³


Storage


1036/11/2006-UK





Spies Hecker Wedgewood Way Stevenage Hertfordshire SG1 4QN

Tel. ++44 (0)1438 734706 Fax ++44 (0)1438 734730

Spies Hecker. A member of DuPont Performance Coatings.


spies hecker

Documents

permasolid hs surfacer

permasolid hs wet

permasolid hs clear

permasolid spectroflex

permasolid hs express

permasolid hs vario

permasolid elastic additive

permasolid diamond clear