s&t vss - begadi...scope is not included automatic electric airsoft gun instruction manual vss...
TRANSCRIPT
Scope is not included
Automatic Electric Airsoft Gun Instruction Manual
VSSS&T VSSST-AEG-21
Always Read Through This Manual Before Operation
USER RESTRICTED TO 18 YEARS OF AGE OF OLDER
WARNING ● CAUTION警告 ● 注意
● Avoid pulling the trigger carelessly.● Always put the gun in a case or bag when you carrying it.● Always set the selector switch to the safety position.● Do not look into the gun muzzle.● Always wear eye protective gear.● Store the airsoft gun at the places out of reach by children.● Do not disassembly or modify the airsoft gun.● Misuse or careless use may cause serious injury.● Never point or shoot at people or animal.● Disassembling or modifying the gun may generate danger.● We are not responsible for any malfunction, accidents, injuries or repair cost resulting from misuse, or by disassembly and modification of the gun.
●●●●●●●●●●●
不意にトリガー(引き金)を引いてしまわないように注意してください。トイガンを運ぶ際は常に必ずガンケースに収納して運んでください。発射するとき意外は常にセフティを掛けておいてください。絶対に銃口を覗かないでください。常にゴーグルを装着してください。エアガンは子供の手に届かないところに保管してください。改造・分解は自己責任において行ってください。誤った使用方法や、注意不足は失明等の深刻な事故を引き起こします。絶対に人や動物に目掛けて発射しないでください。トイガンを分解や改造することは危険を引き起こします。弊社はいかなる作動不良、事故、怪我に関して一切の責任を負いません。また、本商品を分解、改造、誤使用したことによる補修費用は一切負担しません。
®
電動エアーガンVSS/AS-VAL 取り扱い説明書 ご使用の際は必ずこの説明書を全てお読みください
S&T AS-VALST-AEG-22
GENERAL SPECIFICATION各部の名称
- 1 -
Scope MountFolding Stock
Front Sight
Magazine
Selector Switch
Swivel Mount
Receiver Cover
Trigger
Cocking Lever
セレクタースイッチ
トリガー
Magazine Release Catchマガジンリリースレバー
フロントサイトコッキングレバー
レシーバーカバー
150連マガジン
対応バッテリー
マガジン装弾数
発射モード
ホップアップ
全長
インナーバレル長
本体重量
945mm
420mm
2530 g
150 RDS (Cal. 6mm BB)
フルオート / セミオート / セフティ
可変調整式
945mm
420mm
2530 g
150発(6mm BB弾)
フルオート / セミオート / セフティ
可変調整式
690 / 910mm
420mm
2700 g
150発(6mm BB弾)
S&T VSS S&T AS - VAL
690 / 910mm
420mm
2700 g
150 RDS (Cal. 6mm BB)
9.6 AK Type 9.6V AKタイプ 9.6V AKタイプ9.6 AK Type
WARNING ● CAUTION警告 ● 注意
● Avoid pulling the trigger carelessly.● Always put the gun in a case or bag when you carrying it.● Always set the selector switch to the safety position.● Do not look into the gun muzzle.● Always wear eye protective gear.● Store the airsoft gun at the places out of reach by children.● Do not disassembly or modify the airsoft gun.● Misuse or careless use may cause serious injury.● Never point or shoot at people or animal.● Disassembling or modifying the gun may generate danger.● We are not responsible for any malfunction, accidents, injuries or repair cost resulting from misuse, or by disassembly and modification of the gun.
●●●●●●●●●●●
不意にトリガー(引き金)を引いてしまわないように注意してください。トイガンを運ぶ際は常に必ずガンケースに収納して運んでください。発射するとき意外は常にセフティを掛けておいてください。絶対に銃口を覗かないでください。常にゴーグルを装着してください。エアガンは子供の手に届かないところに保管してください。改造・分解は自己責任において行ってください。誤った使用方法や、注意不足は失明等の深刻な事故を引き起こします。絶対に人や動物に目掛けて発射しないでください。トイガンを分解や改造することは危険を引き起こします。弊社はいかなる作動不良、事故、怪我に関して一切の責任を負いません。また、本商品を分解、改造、誤使用したことによる補修費用は一切負担しません。
スコープマウントフォールディングストック
スイベルマウント
Rear Sight
How To Fire
Safety Mode Fire Mode
GENERAL OPERATION
- 2 -
Switch the selector switch to Fire Mode
Pull the trigger
Sliding(forward andbackward)
10
10
155
5
Long distance
Short distancePress
Sight is adjusted according to the distance to the target.
Press the adjust button and slide it forward / backward to move the sight up or down. the larger the number is, the longer distance to the target.
Short distance
Front Sight
Rear Sight
The Correct Sight Picture:
The rear sight has a ‘V’ notch, and the front sight has an inverted ‘V’ post. Simply match them up and make sure they are level and centered.
Full Auto ModeSemi Auto Mode
Press the magazine release catch.
BBs outlet.
MAGAZINE INSTALLATION
Load the Magazine
- 3 -
432
Only use �awless BBS. Never use the following BBs: 1 diameter larger than 6mm, 2 with edges, 3 both halves not aligned, 4 used, soiled
To ensure proper operation of the magazine, protect it from dirt and dust.
1Ø 6 mm
CAUTION
Release the magazine.
6 mm BB.
Wind-up Magazine
Open the magazine BB entrance
min. 30BBs
BATTERY INSTALLATION
- 4 -
The rechargeable battery is installed inside the mock silencer.
Connect the plug.
Turn the mock silencer anti-clockwise to open up the battery compartment.
Connect the plug properly and avoid crushing the cables with the inner barrel.
Install the battery into the mock silencer.
HOP UP ADJUSTMENT
- 5 -
1.
2.
3.
4.
3 cm
1 cm
CAUTION• Do not force the rod into the barrel, as this could
cause damage. • Occasionally clean the metal parts on the outside.
Usea cloth which has been slightly dampened with some weapon oil.
• Never drip silicone oil directly into the barrel.
Piece of cotton
Switch the selector switch on safety Mode. Prepare a thin rod and attach a piece of cotton fabric to its end, clean the barrel with some silicone oil.
Through the test-�re, gradually adjust the dial to give bullets topspin power. the best post position can be achieved is when the trajectory is kept horizontally, and thus the longest �ying distance is obtained.Too much adjustment hop-up or not enough adjustment hop-up will a�ect the trajectory.
Not Enough Hop Up
Excess Hop Up
When moving the cocking lever backwards, the hop-up adjustment lever comes out.Don’t loose the cocking lever when adjusting the hop-up adjustment lever, soas not to injure your �ngers.
- 6 -
通常の操作方法発射方法
発射モード
リアサイトの調整方法
10
10
155
5
右図の調整ボタンを押しながら前後にスライドさせると、そに合わせてサイトが上下します。より大きい数字に合わせると、より遠距離の標的を狙うことが出来ます。
Front Sight
Rear Sight
リアサイトにあるV字型の切欠きからフロントサイトの上端部が見えるように銃を構え、更にその状態でフロントサイトを図の様に標的の中心に合わせます。
セレクタースイッチを回転させ、セミオートかフルオートの位置に切り替えます。
トリガーを引くと発射されます。
セフティモード
セミオートモード フルオートモードトリガーを引くとセミオート(単発)で発射されます。
トリガーを引くとフルオート(連発)で発射されます。
安全装置が働きトリガーがロックされるので発射できなくなります。
正しいサイト(照準器)の合わせ方
遠距離の標的を狙う
近距離の標的を狙う
標的までの距離に合わせてサイトの位置を調整します。
前後にスライドさせます。
両側から矢印の方向に押しロックを解除させます。
- 7 -
432
1 2 3 4
1Ø 6 mm
傷のないBB弾のみ使用してください。次に挙げるようなBB弾は絶対に使用しないで下さい。直径が6mmより大きいもの バリのあるもの 段があり真球状でないもの 一度使用したもの、汚れたもの
マガジンの作動を確実なものとするため、泥や埃から保護してください。
警告
マガジンの装着方法
図の矢印の方向にマガジンリリースレバーを押します。※必ずマガジンを手でしっかり持った状態で操作してください。
マガジン上部前端を中心として、矢印の方向にマガジンを回転させるように取り外します
BB弾の排出口
マガジンの給弾方法
BB弾の給弾口を開き図の様にBB弾を給弾します。
6mmBB弾を最低でも30発以上給弾してください。不足すると巻き上げができず発射できません。
矢印の方向にダイヤルを回し巻き上げます。
- 8 -
バッテリーの装着方法
充電式のバッテリーはダミーのサイレンサー内に収納されます。
ダミーサイレンサーを反時計回りに回転させ、バッテリー収納部を開きます。
バッテリーを図の向きにして、ダミーサイレンサー内に挿入します。
インナーバレルに干渉しないように注意しながらコネクターを接続します。
コネクターを接続します。
- 9 -
1.
2.
3.
4.
3 cm
1 cm
ホップアップが掛かりすぎ
ホップアップが弱すぎ
試し撃ちをしながらダイヤルを調整し、徐々に上向きの回転を加えていってください。発射されたBB弾の軌道が限りなく水平に近い状態が最適なホップアップの調整位置となります。掛かりが強すぎたり、弱すぎたりすると軌道に影響が出ます。(上の図をご参照ください。)
• 内部が破損しますのでクリーニングロッドを無理に押し込まないで下さい。
• 時折、機械油などの油脂類を少量染込ませた布で、外装のメタルパーツを磨いてください。
• バレル内に直接オイルを垂らさないで下さい。
セレクターレバーをセフティの位置にしてください。次に、細長い棒を用意し、その先端に布を巻き、シリコンオイルを数滴染込ませてインナーバレル内を拭いてください。
警告コットン製の布切れ
コッキングレバーを後ろに引くと、チャンバー内のホップアップ調整レバーが露出します。ホップアップレバーを調整する際に、コッキングレバーから手を離さないように注意してください。指をはさみ怪我をする恐れがあります。
ホップアップの調整方法
HOP UPを弱めるHOP UPを強める
EXPLODED DIAGRAM
THE REPLACEMENT PARTS WILL BE AVAILABLE AT OURS LOCAL DEALERS / DISTRIBUTOR.
製品展開図
補修部品に関しては弊社商品輸入代理店、またはご購入の販売店様にお問い合わせください。
S&T VSS
S&T AS - VAL
U01
G01
G02
G03
G04
G05
G06G07
G08G09 G11
G10 G12 G13G14 G15 G16
G17 G18
G19
G20
G21
G22 G23
G24
G25G26 G27
G28 G29 G31
G30
G32 G33
G34G35
G36 G37
G38
G39
G41G42
G43G44
G50
G51
G52
G53
G54
G55
G48
G49
G46G45
M01
M02
LF01
LX01LX15
LX16LX17
LX18
LX06
LX07LX09
LX08
LX19
LX14LX13
LX10LX11
LX12
LX02
LX03LX04
LX05
LX20
LX21
LF02LF03
LF04
LF05
LF06
LF07LF09
LF10
LF11
LF12
LF13
LF14LF15
LF17
LF16
LF18
LF19LF20
LF21
LF08
M03
M04
M05
M06
M07M08
M09M10
M14M11
M12M13
M18
M19
M17M15
M16
G47
G40
U02
U08U09
U10
U11
U12
U13
U14
U15
U16
U17
U18
U19
U20
U21
U22
U23
U24
U25
U26
U27
U28
U29U30
U31
U32
U33U34
U35
U36
U37
U38U39
U40U41
U42
U43
U44
U03
U04 U05
U06 U07