st485eb st485ec - st485ex - stmicroelectronics · 2021. 3. 16. · st485eb - st485ec - st485ex...
TRANSCRIPT
February 2009 Rev 14 1/18
18
ST485EBST485EC - ST485EX
±15 kV ESD protected, low powerRS-485/RS-422 transceiver
Features■ Low quiescent current: 300 µA
■ Designed for RS-485 interface application
■ - 7 V to 12 V common mode input voltage range
■ Driver maintains high impedance in 3-state or with the power OFF
■ 70 mV typical input hysteresis
■ 30 ns propagation delay, 5 ns skew
■ Operates from a single 5 V supply
■ Current limiting and thermal shutdown for driver overload protection
■ ESD protection:– ± 15 kV (HBM)– ± 8 kV (IEC-1000-4-2 contact discharge)
■ Allows up to 256 transceivers on the bus
DescriptionThe ST485E is a low power transceiver for RS-485 and RS-422 communication. Each driver output and receiver input is protected against ± 15 kV electrostatic discharge (HBM) (ESD) shocks, without latch-up. These parts contain one driver and one receiver in half duplex configuration.
This transceiver draws 300 µA (typ.) of supply current when unloaded or fully loaded with disabled drivers.
It operates from a single 5 V supply.
Driver is short-circuit current limited and is protected against excessive power dissipation by thermal shutdown circuitry that place the driver outputs into a high-impedance state.
The ST485E is designed for bi-directional data communications on multipoint bus transmission lines (half-duplex applications).
SO-8
Table 1. Device summary
Order codesTemperature
rangePackage Packaging
ST485EBD - 40 to 85 °C SO-8 (tube) 100 parts per tube / 20 tube per box
ST485ECDR 0 to 70 °C SO-8 (tape and reel) 2500 parts per reel
ST485EBDR - 40 to 85 °C SO-8 (tape and reel) 2500 parts per reel
ST485EXDR - 55 to 125 °C SO-8 (tape and reel) 2500 parts per reel
www.st.com
Contents ST485EB - ST485EC - ST485EX
2/18
Contents
1 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Truth tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5 Test circuit and typical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
ST485EB - ST485EC - ST485EX Pin configuration
3/18
1 Pin configuration
Figure 1. Pin connections (top view)
Table 2. Pin description
Pin n° Symbol Name and function
1 RO Receiver output
2 RE Receiver output enable
3 DE Driver output enable
4 DI Driver input
5 GND Ground
6 A Non-inverting receiver input and non-inverting driver output
7 B Inverting receiver input and inverting driver output
8 VCC Supply voltage
Truth tables ST485EB - ST485EC - ST485EX
4/18
2 Truth tables
Note: X = Don’t care; Z = High impedance
Note: X = Don’t care; Z = High impedance
Table 3. Truth table (driver)
Inputs Outputs
RE DE DI B A
X H H L H
X H L H L
X L X Z Z
Table 4. Truth table (receiver)
Inputs Outputs
RE DE A-B RO
L L ≥ +0.2V H
L L ≤ -0.2V L
L L Inputs open H
H L X Z
ST485EB - ST485EC - ST485EX Maximum ratings
5/18
3 Maximum ratings
Note: Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these is not implied.
Table 5. Absolute maximum ratings
Symbol Parameter Value Unit
VCC Supply voltage 7 V
VI Control input voltage (RE, DE) -0.5 to (VCC + 0.5) V
VDI Driver input voltage (DI) -0.5 to (VCC + 0.5) V
VDO Driver output voltage (A, B) ± 14 V
VRI Receiver input voltage (A, B) ± 14 V
VRO Receiver output voltage (RO) -0.5 to (VCC + 0.5) V
Electrical characteristics ST485EB - ST485EC - ST485EX
6/18
4 Electrical characteristics
VCC = 5 V ± 5 %, TA = TMIN to TMAX, unless otherwise specified. Typical values are referred to TA = 25 °C
Table 6. ESD performance: transmitter outputs, receiver inputs
Symbol Parameter Test conditions Min. Typ. Max. Unit
ESD ESD protection voltage Human body model ±15 kV
ESD ESD protection voltage IEC-1000-4-2 ±8 kV
Table 7. DC electrical characteristics
Symbol Parameter Test conditions (1) Min. Typ. Max. Unit
VOD1Differential driver output (no load)
5 V
VOD2Differential driver output (with load)
RL = 27 Ω (RS-485) (Figure 2)RL = 50 Ω (RS-422) (Figure 2.)
1.555
VV
ΔVOD
Change in magnitude of driver differential output voltage for complementary output states
RL = 27 Ω or 50 Ω (Figure 2) 0.2 V
VOCDriver common-mode output voltage
RL = 27 Ω or 50 Ω (Figure 2) 3 V
ΔVOC
Change in magnitude of driver common-mode output voltage for complementary output states
RL = 27 Ω or 50 Ω (Figure 2) 0.2 V
VIH Input high voltage RE, DE, DI 2.0 V
VIL Input low voltage RE, DE, DI 0.8 V
IIN1 Input current RE, DE, DI ± 2 µA
IIN2 Input current (A, B)VCM = 0 V or 5.25 V, VDE = 0 VVIN = 12 VVIN = -7 V
1-0.8
mAmA
VTHReceiver differential threshold voltage
VCM = -7 to 12 V -0.2 0.2 V
ΔVTH Receiver input hysteresis VCM = 0 V 70 mV
VOH Receiver output high voltage IO = -4 mA, VID = 200 mV 3.5 V
VOL Receiver output low voltage IO = 4 mA, VID = -200 mV 0.4 V
IOZR3-State (high impedance) output current at receiver
VO = 0.4 to 2.4 V ± 1 µA
RIN Receiver input resistance VCM = -7 to 12 V 96 kΩ
ICC No load supply current (2)VRE = 0V or VCCVDE = VCCVDE = 0 V
400300
900500
µAµA
ST485EB - ST485EC - ST485EX Electrical characteristics
7/18
VCC = 5 V ± 5 %, TA = TMIN to TMAX, unless otherwise specified. Typical values are referred to TA = 25 °C
IOSD1Driver short-circuit current, VO=High
VO = -7 to 12 V (3) 35 250 mA
IOSD2Driver short-circuit current, VO=Low
VO = -7 to 12 V (3) 35 250 mA
IOSR Receiver short-circuit current VO = 0 V to VCC 7 95 mA
1. All currents into device pins are positive; all out of device pins are negative; all voltages are referenced to device ground unless specified.
2. Supply current specification is valid for loaded transmitters when VDE = 0 V
3. Applies to peak current. See typical Operating Characteristics.
Table 7. DC electrical characteristics (continued)
Symbol Parameter Test conditions (1) Min. Typ. Max. Unit
Table 8. Driver switching characteristics
Symbol Parameter Test conditions (1) Min. Typ. Max. Unit
tPLH
tPHL
Propagation delay input to output
RDIFF = 54 Ω, CL1 = CL2 = 100 pF(See Figure 4 and Figure 6)
25 45 ns
tSK Output skew to outputRDIFF = 54 Ω, CL1 = CL2 = 100 pF(See Figure 4 and Figure 6)
2 5 ns
tTLHtTHL
Rise or fall timeRDIFF = 54 Ω, CL1 = CL2 = 100 pF(See Figure 4 and Figure 6)
15 40 ns
tPZH Output enable timeCL = 100 pF, S2 = Closed(See Figure 5 and Figure 7)
35 50 ns
tPZL Output enable timeCL = 100 pF, S1 = Closed(See Figure 5 and Figure 7)
25 40 ns
tPLZ Output disable timeCL = 15 pF, S1 = Closed(See Figure 5 and Figure 7)
25 40 ns
tPHZ Output disable timeCL = 15 pF, S2 = Closed(See Figure 5 and Figure 7)
35 50 ns
1. All currents into device pins are positive; all out of device pins are negative; all voltages are referenced to device ground unless specified.
Electrical characteristics ST485EB - ST485EC - ST485EX
8/18
VCC = 5 V ± 5%, TA = TMIN to TMAX, unless otherwise specified. Typical values are referred to TA = 25 °C
Table 9. Receiver switching characteristics
Symbol Parameter Test conditions (1) Min. Typ. Max. Unit
tPLH
tPHL
Propagation delay input to output
RDIFF = 54 Ω, CL1 = CL2 = 100 pF (See Figure 4 and Figure 8)
110 130 ns
tSKD Differential receiver skewRDIFF = 54 Ω, CL1 = CL2 = 100 pF (See Figure 4 and Figure 8)
5 10 ns
tPZH Output enable timeCRL = 15 pF, S1 = Closed(See Figure 2 and Figure 9)
11 35 ns
tPZL Output enable timeCRL = 15 pF, S2 = Closed(See Figure 2 and Figure 9)
13 35 ns
tPLZ Output disable timeCRL = 15 pF, S1 = Closed(See Figure 2 and Figure 9)
13 35 ns
tPHZ Output disable timeCRL = 15 pF, S2 = Closed(See Figure 2 and Figure 9)
11 35 ns
fMAX Maximum data rate 5 Mbps
1. All currents into device pins are positive; all out of device pins are negative; all voltages are referenced to device ground unless specified
ST485EB - ST485EC - ST485EX Test circuit and typical characteristics
9/18
5 Test circuit and typical characteristics
Figure 2. Driver DC test load Figure 3. Receiver timing test load
Figure 4. Drive/receiver timing test circuit Figure 5. Driver timing test load
Test circuit and typical characteristics ST485EB - ST485EC - ST485EX
10/18
Figure 6. Driver propagation delay
Figure 7. Driver enable and disable time
ST485EB - ST485EC - ST485EX Test circuit and typical characteristics
11/18
Figure 8. Receiver propagation delay
Figure 9. Receiver enable and disable time
Test circuit and typical characteristics ST485EB - ST485EC - ST485EX
12/18
Figure 10. Receiver output current vs. output low voltage
Figure 11. Receiver output current vs. output high voltage
Figure 12. Driver output current vs. output low voltage
Figure 13. Driver output current vs. output high voltage
Figure 14. Supply current vs. temperature Figure 15. Receiver high level output voltage vs. temperature
ST485EB - ST485EC - ST485EX Test circuit and typical characteristics
13/18
Figure 16. Receiver low level output voltage vs. temperature
Figure 17. Differential driver output voltage vs. temperature
Package mechanical data ST485EB - ST485EC - ST485EX
14/18
6 Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark.
ST485EB - ST485EC - ST485EX Package mechanical data
15/18
Dim.mm. inch.
Min. Typ. Max. Min. Typ. Max.
A 1.35 1.75 0.053 0.069
A1 0.10 0.25 0.04 0.010
A2 1.10 1.65 0.043 0.065
B 0.33 0.51 0.013 0.020
C 0.19 0.25 0.007 0.010
D 4.80 5.00 0.189 0.197
E 3.80 4.00 0.150 0.157
e 1.27 0.050
H 5.80 6.20 0.228 0.244
h 0.25 0.50 0.010 0.020
L 0.40 1.27 0.016 0.050
k 8° (max.)
ddd 0.1 0.04
SO-8 mechanical data
0016023/C
Package mechanical data ST485EB - ST485EC - ST485EX
16/18
Dim.mm. inch.
Min. Typ. Max. Min. Typ. Max.
A 330 12.992
C 12.8 13.2 0.504 0.519
D 20.2 0.795
N 60 2.362
T 22.4 0.882
Ao 8.1 8.5 0.319 0.335
Bo 5.5 5.9 0.216 0.232
Ko 2.1 2.3 0.082 0.090
Po 3.9 4.1 0.153 0.161
P 7.9 8.1 0.311 0.319
Tape & reel SO-8 mechanical data
ST485EB - ST485EC - ST485EX Revision history
17/18
7 Revision history
Table 10. Document revision history
Date Revision Changes
21-Mar-2006 9 Order codes has been updated and new template.
05-Jun-2006 10 Change value row 10 on the features and RIN in Table 7.
29-Jan-2007 11 Typo mistake on page 1.
29-Aug-2007 12 Change value RIN min. on Table 7.
07-Feb-2008 13 Modified: Table 1 on page 1.
16-Feb-2009 14 Modified: Note: on page 5.
ST485EB - ST485EC - ST485EX
18/18
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve theright to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at anytime, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes noliability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of thisdocument refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party productsor services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of suchthird party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIEDWARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIEDWARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWSOF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOTRECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAININGAPPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVEGRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately voidany warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, anyliability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2009 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com