st5-q-en - servo systems co.servosystems.com/pdf/amp/st5-q-en.pdf · 2020. 2. 27. · the st5-q-en...
TRANSCRIPT
-
Product Datasheet
ST5-Q-ENDC Advanced Microstep Drive w/ Ethernet & Q Programming
Programmablemicrostepping drive with
advanced current controlQ Programmer™ for robust motion controlprogramming744 lines of stored program capabilityMath calculations using analog and digitalparametersSupports all “S” drive control modes as wellCompatible with many 3rd party HMIsWide current range 0.1 to 5.0 A/phase (peakof sine) with idle current reductionAdvanced anti-resonance algorithmTorque ripple smoothingMicrostepping and Microstep Emulation8 digital inputs, 4 digital outputs, opticallyisolated2 analog inputs, +/-10 volt rangeFast 10/100 Ethernet for programming andcommunicationsUDP & TCP support
brianmassey614Typewritten TextSold By: Servo Systems Co. • 53 Green Pond Road, Suite #2 • Rockaway, NJ 07866(973) 335-1007 • Toll Free: (800) 922-1103 • Fax: (973) 335-1661 • www.servosystems.com
-
The ST5-Q-EN stepper drive is a DC-powered microstepping drive for controlling two-phase, bipolar step motors. Itoffers advanced current control and a sophist icated 3rd generation anti-resonance algorithm that electronicallydampens motor and system resonances to improve motor smoothness and usable torque over a wide speed range.The drive also employs electronic torque ripple smoothing and microstep emulation to greatly reduce motor noise andvibration. The drive must be powered from 24-48 VDC and can output up to 5.0 A/phase (peak-of-sine) to the stepmotor. Over-voltage, over-temperature and over-current protection features prevent damage while running in adversecondit ions. The drive is complemented by a specifically matched set of NEMA 11 through NEMA 23 frame steppermotors (see Related and Recommended products below).
The ST5-Q-EN can operate in pulse & direct ion, velocity, and streaming command modes, plus it has the ability to runstand-alone Q programs stored in non-volat ile memory. Q programs are created using the Q Programmer™ software,which provides mult i-tasking, math functions, condit ional processing, data register manipulat ion, and more features in arobust yet simple text-based programming language. The drive is setup and configured using Applied Motion’s STConfigurator™ software. Preconfigured motor setup files included with ST Configurator™ make it easy to set up thedrive for optimum results.
For connecting to external devices such as control signals, incremental encoders, limit switches, proximity orphotoelectric sensors, PLC I/O, lamps, and other devices, the drive comes with 8 digital inputs, 4 digital outputs, and2 single-ended analog inputs (analog inputs can be wired together as 1 differential analog input). Adjustable digitalfilters are present on the digital inputs for enhanced reliability in noisy environments.
The drive comes with an Ethernet port for configuration and programming. The Ethernet port is fast 10/100 Mbit, andthe drive supports both TCP and UPD communication protocols.
All ST drives are CE approved and RoHS compliant.
Description
http://www.applied-motion.com/products/software/q-programmerhttp://www.applied-motion.com/products/software/st-configurator
-
Model Number ST5-Q-EN
Part Number 5000-177
Supply Voltage 24-48 VDC
Supply Voltage Type DC
Control Modes Step & Direct ionVelocity (Oscillator)Streaming CommandsAnalog Posit ioningEncoder FollowingQ Programming
Output Current 0.1-5.0 A/phase
Communication Ports Ethernet
Encoder Feedback No
Step Resolution FullHalfMicrosteppingMicrostep Emulation
Idle Current Reduction 0-90%
Setup Method Software setup
Digital Inputs 8
Digital Outputs 4
Analog Inputs 1 differential or 2 single-ended
Dimensions 5.0 x 3.0 x 1.75 inches
Weight 10.4 oz
Operating TemperatureRange
0-70 °C
Ambient Temperature Range 0-55 °C
Ambient Humidity 90% max, non-condensing
Status LEDs 1 red, 1 green
Circuit Protection Short circuitOver-voltageUnder-voltageOver-temp
Specifications
-
Torque Curves
-
Model Number SupplyVoltage
Control Modes Output Current CommunicationPorts
EncoderFeedback
ST10-C-CE 24-80 VDC CANopen 0.1-10.0A/Phase
RS-232CANopen
Yes
ST10-C-CN 24-80 VDC CANopen 0.1-10.0A/Phase
RS-232CANopen
No
ST10-IP-EE 24-80 VDC
Streaming CommandsAnalog PositioningEncoder FollowingQ Programming
EtherNet/IP
0.1-10.0A/Phase
EthernetEtherNet/IP Yes
ST10-IP-EN 24-80 VDC
Streaming CommandsAnalog PositioningEncoder FollowingQ Programming
EtherNet/IP
0.1-10.0A/Phase
EthernetEtherNet/IP No
ST10-Plus 24-80 VDC
Streaming CommandsAnalog PositioningEncoder FollowingQ Programming
0.1-10.0A/Phase
RS-232 No
ST10-Q-EE 24-80 VDC
Step & DirectionVelocity (Oscillator)
Streaming CommandsAnalog PositioningEncoder FollowingQ Programming
0.1-10.0A/Phase
Ethernet Yes
ST10-Q-EN 24-80 VDC
Step & DirectionVelocity (Oscillator)
Streaming CommandsAnalog PositioningEncoder FollowingQ Programming
0.1-10.0A/Phase
Ethernet No
ST10-Q-NE 24-80 VDC
Step & DirectionVelocity (Oscillator)
Streaming CommandsAnalog PositioningEncoder Following
0.1-10.0A/Phase RS-232 Yes
2D Drawings
Products in the Series ST Stepper Drives
http://www.applied-motion.com/products/stepper-drives/st10-c-cehttp://www.applied-motion.com/products/stepper-drives/st10-c-cnhttp://www.applied-motion.com/products/stepper-drives/st10-ip-eehttp://www.applied-motion.com/products/stepper-drives/st10-ip-enhttp://www.applied-motion.com/products/stepper-drives/st10-plushttp://www.applied-motion.com/products/stepper-drives/st10-q-eehttp://www.applied-motion.com/products/stepper-drives/st10-q-enhttp://www.applied-motion.com/products/stepper-drives/st10-q-ne
-
Q ProgrammingSiNet Hub Compatible
ST10-Q-NN 24-80 VDC
Step & DirectionVelocity (Oscillator)
Streaming CommandsAnalog PositioningEncoder FollowingQ Programming
SiNet Hub Compatible
0.1-10.0A/Phase RS-232 No
ST10-Q-RE 24-80 VDC
Step & DirectionVelocity (Oscillator)
Streaming CommandsAnalog PositioningEncoder FollowingQ Programming
0.1-10.0A/Phase
RS-232RS-485
Yes
ST10-Q-RN 24-80 VDC
Step & DirectionVelocity (Oscillator)
Streaming CommandsAnalog PositioningEncoder FollowingQ Programming
0.1-10.0A/Phase
RS-232RS-485
No
ST10-S 24-80 VDC
Step & DirectionVelocity (Oscillator)
Streaming CommandsSiNet Hub Compatible
0.1-10.0A/Phase
RS-232 No
ST10-Si-NE 24-80 VDC Si Programming 0.1-10.0A/Phase
RS-232 Yes
ST10-Si-NN 24-80 VDC Si Programming 0.1-10.0A/Phase
RS-232 No
ST5-C-CE 24-48 VDC CANopen 0.1-5.0A/Phase
RS-232CANopen
Yes
ST5-C-CN 24-48 VDC CANopen 0.1-5.0A/Phase
RS-232CANopen
No
ST5-IP-EE 24-48 VDC
Streaming CommandsAnalog PositioningEncoder FollowingQ Programming
EtherNet/IP
0.1-5.0A/Phase
EthernetEtherNet/IP Yes
ST5-IP-EN 24-48 VDC
Streaming CommandsAnalog PositioningEncoder FollowingQ Programming
EtherNet/IP
0.1-5.0A/Phase
EthernetEtherNet/IP No
ST5-Plus 24-48 VDC
Streaming CommandsAnalog PositioningEncoder FollowingQ Programming
0.1-5.0A/Phase
RS-232 No
ST5-Q-EE 24-48 VDC
Step & DirectionVelocity (Oscillator)
Streaming CommandsAnalog PositioningEncoder FollowingQ Programming
0.1-5.0A/Phase
Ethernet Yes
ST5-Q-EN 24-48 VDC
Step & DirectionVelocity (Oscillator)
Streaming CommandsAnalog PositioningEncoder FollowingQ Programming
0.1-5.0A/Phase
Ethernet No
ST5-Q-NE 24-48 VDC
Step & DirectionVelocity (Oscillator)
Streaming CommandsAnalog PositioningEncoder FollowingQ Programming
SiNet Hub Compatible
0.1-5.0A/Phase RS-232 Yes
ST5-Q-NN 24-48 VDC
Step & DirectionVelocity (Oscillator)
Streaming CommandsAnalog PositioningEncoder FollowingQ Programming
SiNet Hub Compatible
0.1-5.0A/Phase RS-232 No
ST5-Q-RE 24-48 VDC
Step & DirectionVelocity (Oscillator)
Streaming CommandsAnalog PositioningEncoder FollowingQ Programming
0.1-5.0A/Phase
RS-232RS-485
Yes
ST5-Q-RN 24-48 VDC
Step & DirectionVelocity (Oscillator)
Streaming CommandsAnalog PositioningEncoder FollowingQ Programming
0.1-5.0A/Phase
RS-232RS-485
No
http://www.applied-motion.com/products/stepper-drives/st10-q-nnhttp://www.applied-motion.com/products/stepper-drives/st10-q-rehttp://www.applied-motion.com/products/stepper-drives/st10-q-rnhttp://www.applied-motion.com/products/stepper-drives/st10-shttp://www.applied-motion.com/products/stepper-drives/st10-si-nehttp://www.applied-motion.com/products/stepper-drives/st10-si-nnhttp://www.applied-motion.com/products/stepper-drives/st5-c-cehttp://www.applied-motion.com/products/stepper-drives/st5-c-cnhttp://www.applied-motion.com/products/stepper-drives/st5-ip-eehttp://www.applied-motion.com/products/stepper-drives/st5-ip-enhttp://www.applied-motion.com/products/stepper-drives/st5-plushttp://www.applied-motion.com/products/stepper-drives/st5-q-eehttp://www.applied-motion.com/products/stepper-drives/st5-q-enhttp://www.applied-motion.com/products/stepper-drives/st5-q-nehttp://www.applied-motion.com/products/stepper-drives/st5-q-nnhttp://www.applied-motion.com/products/stepper-drives/st5-q-rehttp://www.applied-motion.com/products/stepper-drives/st5-q-rn
-
Q Programming
ST5-S 24-48 VDC
Step & DirectionVelocity (Oscillator)
Streaming CommandsSiNet Hub Compatible
0.1-5.0A/Phase
RS-232 No
ST5-Si-NE 24-48 VDC Si Programming 0.1-5.0A/Phase
RS-232 Yes
ST5-Si-NN 24-48 VDC Si Programming 0.1-5.0A/Phase
RS-232 No
http://www.applied-motion.com/products/stepper-drives/st5-shttp://www.applied-motion.com/products/stepper-drives/st5-si-nehttp://www.applied-motion.com/products/stepper-drives/st5-si-nn
Product DatasheetST5-Q-ENDC Advanced Microstep Drive w/ Ethernet & Q ProgrammingProduct FeaturesDescriptionSpecificationsSoftwareDownloadsPricingTorque Curves2D DrawingsProducts in the Series ST Stepper Drives