UM-032e

Cal

l Cor

d

ON

/ O

FF

Cord

Rem

oval

Alar

m

Antenna

Program Button

If using optional Nurse Call Pendantset switch to ON position else leave OFF.

Always leave switch in ON position.

Reset Button1. Will clear any fault conditions e.g. Signal Lost or Low Battery2. If no fault condition, then it will activate a 3 minute delay.Status LED will flash during the delay and no alarms will be generated.Pressing again before the 3 minutes have elapsed will return the unit to normal operation.

Plug hardwired Bed/Chair Pad

or Floor Mat in here. Antenna

wire

2544 Cordless Multiport Expander

Optional Accessories (Sold Seperately)

2719 Cordless Pad Transmitter2629 Cordless Bed Pad

2630 Cordless Chair Pad2624 Cordless Floor Mat

2406M Plug Pack 6V Power Adaptor2721 iBeam

2588 Personal Emergency Transmitter (PET)

3503 Wireless Magnetic Reed Switch

2558 Wireless Waterproof Call Button

3502 Wireless Handset

Optional 2406MPlug Pack 6Vdc

Optional 2638 Nurse Call Pendant

Do not immerse or wash pads or mats under running water. Use a damp cloth (1/1000 bleach solution) & wipe clean. Dry all spills on mats immediately.

All our products are supplied with a full warranty and are guaranteed to be free from defects in material and workmanship

Do NOT fold pads or mats when in transit or storage.

Keep pads & matsflat at all times

Bottom View

Back View

Program

Pad/MatDC 6V

0.5A

Side View

Plug Multiport Expander

directly into nurse call

system.

Warning! Do NOT insert or remove

adaptor at an angleor else damage

may occur.

Top View

Reset

Error Status

FrontView

Status LED: Green

Error LED: Yellow/Red

Blinking Pad ActiveON Alarm Trigger

Flashes Adaptor Cordless Pad(Yellow) (Red)

1 Low Bat. Pad Low Bat.2 Pad Signal Lost

Disconnect3 AC Lost

Error Indicator LED

StatusIndicator LED

Error & Status Indicator LED explanation.

1

QUICK START GUIDE2544 Cordless Multiport Expander

Step

Error Status

Insert 3 X AAA alkaline batteries into battery compartment.

Release screwto open batterycompartment.

Error Status

Insert 3 x AAA alkaline batteries into battery compartment.

2Step Pair Multiport Expander with transmitter/s. Transmitters can be a Cordless Bed / Chair Pad, Cordless Floor Mat, Personal Emergency Transmitter (PET), iBeam, Magnetic Reed Switch, Waterproof Call Button or Wireless Handset.

1. Place transmitters to be programmed within easy reach.

2544 Multiport Expanders are designed to work in a facility on alkaline batteries equivalent to those originally supplied with the device.

Operable alkaline batteries must be installed in the device at all times during operation. Batteries must be removed from the device while it’s in storage.

Use of an optional 2406M Plug Pack will extend the usable battery life. Essentially a Plug Pack may not be required in most instances.

Please Note: A 2719 Transmitter Insert which has been switched off will be in hibernation mode when it is switched on again. Be sure to activate it for 15 seconds to wake it up so that you can test it in Step 3. Please refer to the documentation that came with your 2719 Transmitter if you require more information.

Error Status

3

Test Multiport Expander prior to every use.

Cordless floor mat is placed on floor in doorway or beside

the bed

Alarm signals sentto adaptor 10m max.

Personal EmergencyTransmitter (PET)

Step Plug Multiport Expander into nurse call system & test operation of all devices in their final location.

Bed or Chair Pad with 2719 Transmitter

Insert.

ON OFF

Cordless Pad or Mat

2. Clear the program memory: Press & hold the Program button until the Error & Status LEDs illuminate. Keep holding down the Program button until the LEDs flash quickly, then release.

3. Enter Program Mode: Press & hold the Program button on the Multiport Expander until the Error & Status LEDs illuminate. Now release the Program button.

4. Pair the first transmitter: - For a 2719 Cordless Pad / Mat Transmitter: turn the transmitter from OFF to ON. The Error LED will flash once to acknowledge succesful pairing - For all other transmitters: Activate the transmitter (trigger an alarm). The Status LED will flash once to acknowledge successful pairing.After a successful pairing the Multiport Expander will exit Program Mode and the Status and Error LEDs will go out.

5. Pair remaining transmitters: Repeat step 3 & 4 for each transmitter to be paired. Up to 2 Cordless Pad / Mat Transmitters and up to 3 other devices can be paired with each Multiport Expander.

6. If 2719 Transmitter is used then connect it to Cordless Pad or Mat & ensure that it is switched ON.