steel cable tray - gescan - distributor of electrical ... steel accessories, splice plates cable...
TRANSCRIPT
144
Accessories and Covers
SteelCable Tray
– Tray covers are available for all classes of tray. They should be installed where falling objects may damage cables or where vertical tray run is accessible by pedestrian or vehicular traffic.
Outside cable tray runs should be covered with a Peaked Flanged cover to protect cable from the elements and excess build up of snow and ice.
Tray Covers
– These covers provide maximum mechanical protection for cables with limited heat build up. Solid covers are available with or without flange. Flanged covers have 1/2" flange.
Solid Covers
– This design offers excellent mechanical protection while allowing heat produced by cables to dissipate.
Ventilated Flanged Covers
– Peaked covers offer mechanical protection plus prevents accumulation of liquid on the cover. Peaked covers have 15° rise at the peak. Covers greater than 12" wide *available in 72" and 3 m lengths.
Peaked Flanged Covers
Solid Flanged Solid Non-Flanged
VentilatedFlanged
Peaked Flanged
Cover mounting hardware must be ordered separately.
Cover mounting hardware must be ordered separately.
Cover mounting hardware must be ordered separately.
145
Accessories and Covers
SteelCable Tray
Straight Cover Number Selection
( S P W 1 2 ) S N C - 3MaterialPrefix
SPW • Pre-Galvanized
SHW• Hot Dip Galvanized*
SSW • Stainless Steel 316
Length
72 • (72”)
144 • (12ft)
3 • (3m)
Type
SNC • Solid Non-Flanged Cover
SFC • Solid Flanged Cover
VFC • Ventilated Flanged Cover
**PFC • Peaked Flanged Cover
Width
06 • (6")09 • (9")12 • (12")18 • (18")24 • (24")30 • (30")36 • (36")
* Hot Dipped Covers only available in 72” and 1500 mm lengths.** Peaked covers greater than 12” wide available in 72” and 3m lengths only.
Straight Covers
Fitting Covers
Fitting Cover Number Selection
( S P W 1 2 ) S N C H B 9 0 2 4
Width
06 • (6")09 • (9")12 • (12")18 • (18")24 • (24")30 • (30")36 • (36")
Cover Type
SNC •Solid Non-Flanged Cover
SFC •Solid Flanged Cover
VFC •Ventilated Flanged Cover
Radius
12 • (12”)
24 • (24”)
36 • (36”)
48 • (48”)
Fitting Type
HB • Horizontal BendHT • Horizontal TeeHX • Horizontal CrossVI • Vertical Inside BendVTU • Vertical Tee DownHYR • Horizontal Wye RightHYL • Horizontal Wye Left
Degree
30 • (30o)
45 • (45o)
60 • (60o)
90 • (90o)
MaterialPrefix
SPW • Pre-Galvanized
SHW• Hot Dip Galvanized
SSW • Stainless Steel 316
*
* Required for HB & VI onlyPrefix
Prefix
Ste
elA
cces
sorie
s
Fitting Cover Number Selection
( S P W 4 1 2 ) S N C V O 9 0 2 4
146
SteelCable Tray
Fitting Covers (cont’d)
SiderailHeight
3 • (3-5/8")4 • (4")5 • (5")6 • (6")7 • (7")
CoverType
SNC •Solid Non-FlangedCover
SFC •Solid FlangedCover
VFC •Ventilated FlangedCover
Radius
12 • (12”)
24 • (24”)
36 • (36”)
48 • (48”)
Fitting Type
VO • VerticalOutsideBend
VTD • VerticalTee Down
CS • CableSupportFitting
Degree
30 • (30o)
45 • (45o)
60 • (60o)
90 • (90o)
MaterialPrefix
SPW • Pre-Galvanized
SHW• Hot Dip Galvanized
SSW • Stainless Steel 316
*
* Required for VO only
Accessories and Covers
Fitting Cover Number Selection
( S P W 1 8 1 2 ) S N C R T 1 2
Width 1
06 • (6")09 • (9")12 • (12")18 • (18")24 • (24")30 • (30")36 • (36")
Cover Type
SNC •Solid Non-Flanged Cover
SFC •Solid Flanged Cover
VFC •Ventilated Flanged Cover
Radius
12 • (12”)
24 • (24”)
36 • (36”)
48 • (48”)
Fitting Type
RT • Horizontal Reduce TeeET • Horizontal Expand TeeEX • Horizontal Expand
Tee & Reduce CrossHSR • Horizontal Straight
ReducerHLR • Horizontal Left
ReducerHRR • Horizontal Right
Reducer
MaterialPrefix
SPW • Pre-Galvanized
SHW• Hot Dip Galvanized
SSW • Stainless Steel 316
Width 2
06 • (6")09 • (9")12 • (12")18 • (18")24 • (24")30 • (30")36 • (36")
* Radius notrequired for
HSR, HLR, HRR
*
Prefix
Width
06 • (6")09 • (9")12 • (12")18 • (18")24 • (24")30 • (30")36 • (36")
Prefix
Quantity of Standard Cover Clamps Required
Straight section (6 ft) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 pcs.Straight section (12 ft) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 pcs.Horizontal and Vertical Bends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 pcs.Tees . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 pcs.Crosses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 pcs.
147
SteelCable TrayAccessories and Covers
Note: When using the Heavy Duty Cover Clamp, only half the quantity of pieces are required.
Material CoverPrefix Offset Catalogue Number
(+) Insert Cover Offset
Designed to raise cover abovetray for added ventilation.
Raised Cover Clamp
Peaked End Cap
(*) Insert Width of Tray
Used for transition between peaked covers to straight covers.
Cover
Siderail
SPW 1” SPW(+)RCCSSW 2”
3”
MaterialPrefix Width Catalogue NumberSPW 06” SPW(*)PECSHW 09” SHW(*)PECSSW 12”
18”24”30”36”
Combination Hold Down Cover Clamp
Designed to secure flat and flanged covers with hold downfeature.
Material SiderailPrefix Height Catalogue NumberSPW 3” SPW-3-CCCSSW 4” SPW-4-CCC
5” SPW-5-CCC6” SPW-6-CCC7” SPW-7-CCC
Ste
elA
cces
sorie
s
Cover Clamp
148
SteelCable Tray Accessories and Covers
Rigid indoor cover clamp forflat and flanged covers.
Material SiderailPrefix Height Catalogue NumberSPW 3” (Prefix)-3-SCCSSW 4” (Prefix)-4-SCC
5” (Prefix)-5-SCC6” (Prefix)-6-SCC7” (Prefix)-7-SCC
Heavy Duty Peaked Cover Clamp
Heavy Duty Cover Clamp
(*) Insert Width of Tray.
Wrap around design offersadded protection for ruggedapplications and outdoorconditions.Hardware included
Material Siderail WidthPrefix Height of Tray Catalogue Number
SPW 3” 06” (Prefix)-3-(*)-HCCSHW 4” 09” (Prefix)-4-(*)-HCCSSW 5” 12” (Prefix)-5-(*)-HCC
6” 18” (Prefix)-6-(*)-HCC7” 24” (Prefix)-7-(*)-HCC
30”36”
Wrap around designformed to fit peaked coverfor outdoor applications.Hardware included.
Material Siderail WidthPrefix Height of Tray Catalogue Number
SPW 3” 06” (Prefix)-3-(*)-HPCSHW 4” 09” (Prefix)-4-(*)-HPCSSW 5” 12” (Prefix)-5-(*)-HPC
6” 18” (Prefix)-6-(*)-HPC7” 24” (Prefix)-7-(*)-HPC
30”36”
(*) Insert width of tray.
Cover Joint Strip
Strip used for joining coversend to end.
Material WidthPrefix of Tray Catalogue NumberSPW 6” SPW-(*)-SCS
9”12”18”24”30”36”
(*) Insert width of tray.Note: material is plastic.
149
SteelCable TrayAccessories, Splice Plates
Splice Plate
Packaged in pairs with zincplated hardware.Provided as standard with eachstraight and/or fitting.
Material SiderailPrefix Height Catalogue NumberSPW 3” (Prefix)-3-SSPSHW 4” (Prefix)-4-SSPSSW 5” (Prefix)-5-SSP
6” (Prefix)-6-SSP7” (Prefix)-7-SSP
Expansion Splice Plate
Allows for a 1” expansion orcontraction of tray system. Packaged in pairs withhardware.
Material SiderailPrefix Height Catalogue NumberSPW 3” (Prefix)-3-ESPSHW 4” (Prefix)-4-ESPSSW 5” (Prefix)-5-ESP
6” (Prefix)-6-ESP7” (Prefix)-7-ESP
Horizontal Adjustable Plate
Material For TrayPrefix Widths Catalogue Number
SPW 6” (Prefix)-(*)06HAPSHW 9” (Prefix)-(*)09HAPSSW 12” (Prefix)-(*)12HAP
18” (Prefix)-(*)18HAP24” (Prefix)-(*)24HAP30” (Prefix)-(*)30HAP36” (Prefix)-(*)36HAP42” (Prefix)-(*)42HAPAdjustable hinge plates provide
maximum horizontal installationflexibility.Furnished in pairs withhardware.
Step Down Splice Plate
MaterialPrefix Catalogue Number
SPW (Prefix)-(*)-(**)-SDSSHWSSW
Connects siderails of differentheights.Hardware included.
(*) Insert siderail height 1(**) Insert siderail height 2
Note: Siderail height is greater than siderail height 2.
(*) Insert Siderail Height.
Ste
elA
cces
sorie
s
150
SteelCable Tray Accessories, Splice Plates
Vertical Adjustable Plate
Material SiderailPrefix Height Catalogue NumberSPW 3” (Prefix)-3-VSPSHW 4” (Prefix)-4-VSPSSW 5” (Prefix)-5-VSP
6” (Prefix)-6-VSP7” (Prefix)-7-VSPHinged vertical plates provide
maximum flexibility for changesin elevation.Packaged in pairs withhardware.
Closure End Plate
Box to Tray Plates
Designed to secure tray toelectrical panels or boxes, wallsor end supports.Packaged in pairs with hardware..
Material SiderailPrefix Height Catalogue NumberSPW 3” (Prefix)-3-BSPSHW 4” (Prefix)-4-BSPSSW 5” (Prefix)-5-BSP
6” (Prefix)-6-BSP7” (Prefix)-7-BSP
Provides closure for any tray end.Hardware included.
Material SiderailPrefix Height Catalogue NumberSPW 3” (Prefix)-3-(*)-CEPSHW 4” (Prefix)-4-(*)-CEPSSW 5” (Prefix)-5-(*)-CEP
6” (Prefix)-6-(*)-CEP7” (Prefix)-7-(*)-CEP
Reducing Splice Plate
Material SiderailPrefix Height Catalogue NumberSPW 3” (Prefix)-3-(*)-RSPSHW 4” (Prefix)-4-(*)-RSPSSW 5” (Prefix)-5-(*)-RSP
6” (Prefix)-6-(*)-RSP7” (Prefix)-7-(*)-RSP
Used in pairs to provide a straightreduction or used with a StandardSplice Plate for an offset reduction.One per package with hardware.
*Note: For Offset Reduction: Insert width to be reduced.For Straight Reduction: Insert 1/2 width to be reduced (2 required)
Example: SPW-503-RSP = 3” offset reducer
* Tray Width
151
SteelCable Tray
Accessories,Hold Down Clamps /Hardware
MaterialPrefix Catalogue Number
Standard Hold down Clamp
Designed for most indoorinstallations.Easy to use and install.Order 1/4” hardware separately.
MaterialPrefix Catalogue Number
SPW (Prefix)-HECSHWSSW
Combination Hold Down / Expansion Clamp
Order 1/4” hardware separately.
SPW (Prefix)-SHCSSW
SPW (Prefix)-SHC-HDWSSW
Hold Down Clamp
Material SiderailPrefix Height Catalogue NumberSPW 3” (Prefix)-3-HDCSSW 4” (Prefix)-4-HDC
5” (Prefix)-5-HDC6” (Prefix)-6-HDC7” (Prefix)-7-HDC
Note: Hardware included
Note: HDW = Supplied complete with 1/4” hardware
Ste
elA
cces
sorie
s
Zinc Plated Steel Self-Drilling – Tapping Screw SPW-10-SCR
152
Accessories,Hold Down Clamps /
Hardware
SteelCable Tray
Self-Drilling – Tapping Screw
MaterialPrefix Description Catalogue Number
Steel Tray Hardware
Square shoulder self-positioningcarriage bolt.
Description Material Catalogue Number
1/4” Carriage Bolt Zinc Plated Steel SPW-1/4-CB3/8” Carriage Bolt Zinc Plated Steel SPW-3/8-CB1/4” Hex. Nut Zinc Plated Steel SPW-1/4-HN3/8” Hex. Nut Zinc Plated Steel SPW-3/8-HN
3/8” Carriage Bolt 316 Stainless SS6W-3/8-CB3/8” Hex. Nut 316 Stainless SS6W-3/8-HN316 Stainless Steel 316 Stainless SS6W-3/8-HWK*Hardware Kit
* Contains 8 nuts, 8 bolts, 8 lockwashers
(*) Insert Width of Tray+ DOS = is for solid Tray
153
SteelCable TrayAccessories, Cable Protection
Wall Penetration Sleeve
Drop-Out
Frame Type Tray to Box Plate
Nylon Expansion Pad
Designed to provide a smoothradiused surface at any position onthe tray or trough bottom. Drop-Outsare easily attached using hardwareprovided.Standard Radius = 4".
Designed to pass through wallsand fire walls.Hardware included.
Note: Not Fire Rated. Fire Stop not included.
Designed to secure tray toelectrical enclosures andpanels.
Hardware included.
Allows for thermal expansionand contraction of cable traysover supports.
Material TrayPrefix Width Catalogue Number
SPW 06 (Prefix)-(*)-DOSHW 09 (Prefix)-(*)-DOSSSW 12
18243036
Material Siderail TrayPrefix Height Width Catalogue Number
Material Catalogue Number
Natural Nylon ABW-NSP
SPW 3” 06 (Prefix)-(*)-(**)-WPSSHW 4” 09SSW 5” 12
6” 187” 24
3036
+
Material Siderail TrayPrefix Height Width Catalogue NumberSPW 3” 06 (Prefix)-(*)-(**)-FBPSHW 4” 09SSW 5” 12
6” 187” 24
3036
(*) Insert Siderail Height(**) Insert Width of Tray
Ste
elA
cces
sorie
s
(*) Insert Siderail Height(**) Insert Width of Tray
154
SteelCable Tray Accessories, Barrier Strips
Inside/Outside Vertical Bend Barriers
Barrier Strips
Barrier Strips provide a methodof separating cables in tray andtrough systems. Easily installedusing supplied hardware orBarrier Strip Clamps (soldseparately). 72" Barriers areflexible for use with horizontalfittings.
Material SiderailPrefix Height *Length Catalogue Number
Preformed to fit all standardsteel vertical bends.Provided with hardware.
Barrier Strip Clamp
Barrier Strip Clamps mountBarrier Strips to Ladder rungsand Ventilated Trough bottoms.Complete mounting hardwaresupplied.
Barrier Strip Splice
Alignment splice for joiningconnecting Barrier Strips.
SBH
SB
SPW 3” 72” (Prefix)-3-(*)-SBH-72SHW 4” (Prefix)-4-(*)-SBH-72SSW 5” (Prefix)-5-(*)-SBH-72
6” (Prefix)-6-(*)-SBH-727” (Prefix)-7-(*)-SBH-72
SPW 3” 144” (Prefix)-3-SB-(*)SHW 4” 3m (Prefix)-4-SB-(*)SSW 5” (Prefix)-5-SB-(*)
6” (Prefix)-6-SB-(*)7” (Prefix)-7-SB-(*)
NOTE: 72” barriers provided with 3 SPW10SCR144”, 3m barriers provided with self drilling-tapping screw cat. no. SPW10SCR
72’’ length, 3 screw3m length, 5 screw144’’ length, 6 screw
Material Inside Bend Outside Bend SiderailPrefix Catalogue Number Catalogue Number Height
SPW (Prefix)-3-VIB-(*)-(+) (Prefix)-3-VOB-(*)-(+) 3”SHW (Prefix)-4-VIB-(*)-(+) (Prefix)-4-VOB-(*)-(+) 4”SSW (Prefix)-5-VIB-(*)-(+) (Prefix)-5-VOB-(*)-(+) 5”
(Prefix)-6-VIB-(*)-(+) (Prefix)-6-VOB-(*)-(+) 6”(Prefix)-7-VIB-(*)-(+) (Prefix)-7-VOB-(*)-(+) 7”
(*) Insert Bend Degree (+) Insert Bend Radius
MaterialPrefix Catalogue NumberSPW (Prefix)-BSCSSW
Material Catalogue NumberPlastic ABW-BSS
Note: SHW barriers are only available in 72” or 1500 mm
155
SteelCable TrayAccessories, Cable Tray Guide
Cable Tray Clamp
Cable Tray Guide
Expansion guide for single or double runs ofcable tray.No need to field drill channel or I-beam.
Clamps for single run of cable tray.No need to field drill channel or I-beam.
Vertical Tray Hanger
Material Catalogue NumberZinc Plated Steel SPW-CTGSteel Hot Dip SHW-CTGStainless Steel SSW-CTG
Material Catalogue NumberZinc Plated Steel SPW-CTCSteel Hot Dip SHW-CTCStainless Steel SSW-CTC
Material SiderailPrefix Height Catalogue Number
SPW 3” (Prefix)-(*)-VTHSHW 4”SSW 5”
6”7”
Ste
elA
cces
sorie
s
(*) Insert Siderail Height