steel scrolling
TRANSCRIPT
-
7/27/2019 Steel Scrolling
1/23
Steel Scrolling/Coiling 101
4ft long square bar left, 20ft long " round HRS bar right, 3/8th HRS paperwieght on the collar.
I dont know how I got into scrolling/coiling. I guess Tommy Heslep introduced me.
Thanks to him I got to meet Big Steve and I saw a clip of Brookfield scrolling some square bar.Well, after that Im hooked. Ive searched the internet and the beloved Gripboard to learn as much
as possible. Unfortunately, I didnt learn that much. This is an area of grip strength/classic
strength feat that has very little info available. Fortunately, Brookfield touched on this area in the
book The Grip Masters Manuel (GMM). If you havent read it you should. Nobody is better than
Brookfield when it comes to this stuff.
I started out with short bending. Pieces of steel 7 inches in length and shorter. These
pieces of steel were cut to specific lengths to simulate specific nails. (If you need information on
short bending go to the Bending forum of the Gripboard. Theres tons of info there.) I purchased
my steel at a local steel supplier. This is by far the cheapest way to buy steel. Well, I had some
1/4" square and 3.8ths rods and they were too tough for little old me to do any short bending with.After getting sick of lookin at the tough bars I decided to coil em up. So I guess you could say I
got hooked by accident or my own weakness. Hehehehehe.....
Well, after coiling the 1/4" square and 3/8ths round HRS ( Hot Rolled Steel) Id gotten a
decent amount of practice. This had allowed me to learn some of the basic techniques. Brookfield
recommends this in the GMM. Practice with the small stuff first! Youll reap a lot if you do.
Before we get too carried away Ill touch on some basic terminology before we all get
-
7/27/2019 Steel Scrolling
2/23
confused.
Coiling means you put as many coils in the steel as possible. So the steel ends up looking like a
gripper spring or a garden hose rolled up.
Scrolling refers to bending the steel into an artistic shape. This is vague. It may mean you bentthe steel into the shape of a clover leaf, or some abstract art. Basically, the steel has more twists
and turns and it is not just coiled. We will focus on coiling.
Again, Brookfield talks about this in GMM. We wont get too wrapped up in definitions because
the 2 are so closely related. For example, in the previous picture you could say the bar that looks
like a fish is scrolled. Even though the same techniques were used to bend it.
Left pic: 1/4" square and 1/4"round scroll. Notice how thesquare bar bends on the edge! Youll see this again!
Right pic: 3/8 ths left, " right. You can tell the difference in diameter and the size of the coils. Practice with 3/8".
If you want more pictures examples outside of this article go to www.samsonscroll.com. This is
John Brookfields web page. There are loads of pictures.
Starting Off
If you want to get into this area of steel bending youll need a few things.
1. Gloves. You can use any type of good leather work gloves. These are important for cutting
and for providing protection to your palms when youre exerting a lot of force.
2. Glasses/face shield. These are important when you cut steel because there will be sparks flying!
You may want to use them when you are bending bigger pieces of HRS (Hot Rolled Steel). HRS
has a coating that flakes off when bent. This can get in your eyes too.
-
7/27/2019 Steel Scrolling
3/23
3. You need some way to cut the steel. Bolt cutters only work for small steel, 3/8ths in diameter
and less. So, you will need a hacksaw, a sawzall, or an angle grinder. I highly recommend the
angle grinder! The cuts are very clean and it cuts the steel quickly. Its also cheap compared to
the sawzall. Be sure to buy extra cutting wheels and replace them as needed.
4. Finally youll need steel. Now dont go to Home Depot or Lowes. Youll spend way too muchmoney. Go to your local steel supplier and buy your bars in 20ft lengths. Trust me on this, you
will save a lot of money.
Cuttin steel. This is cool stuff!!!!!!
Ok, so weve gone to the local steel supplier and weve purchased a few steel bars! Man
this is great! Oh crap! The 20ft bars will not fit in my little Japanese Jellybean of a car! Well,
HAVE NO FEAR! Because we brought an angle grinder. We are about to make a whole lot of
sparks and cut this steel. But first you need to pull out you tape measure and permanent marker. I
know, I know. I didnt say you needed the tape measure and the marker. Well you do! Im
writing this and youre reading it! Unless you want to waste steel youll do what I say!Youll measure you lengths and mark the steel with the marker. If you do this you only
have to cut once. For example, you have a 20ft bar of inch round HRS and you want 4ft
sections. You need to mark it correctly so you get 5 perfectly cut 4 ft bars to bend the crap out of!
See, no wasted steel. The only time you should be cutting steel and discarding small sections is to
shorten bars as you get stronger or if you are trimming the extra off a complete bend.
-
7/27/2019 Steel Scrolling
4/23
This is what I use to cut steel and I couldnt be happier with it!
Practice makes perfect!
Remember I said start off with 3/8" round? I meant it. Dont think What does that
Hammered know? Hes a small wimp I can start with bigger stuff!! Im a badass!! The 3/8"
round is great. Youll get a feel for coiling/scrolling, and youll make some super cool
paperweights too! Besides, its cheap compared to the bigger steel sizes so there is no reason not
to practice with it.
Sierra with a 3/8ths inch scroll.
-
7/27/2019 Steel Scrolling
5/23
Bigger Steel!Sorry I got carried away with the font size. I just got excited since we are moving on to
the bigger stuff! Steel comes in different diameters which is great for us. It allows us to use
progressively get stronger kinda like using weights or a shot loadable kettlebell. Brookfield
explains bar diameters in depth in GMM. Basically, you pick a bar like " round HRS. The next
step up will be the same size in CRS (cold rolled steel) if available. Finally, the next step will be
" again but square HRS. Then you move to the next diameter. Talk to the steel supplier in
you area. Some suppliers may carry different diameters and HRS/CRS.
round ----> square ----> 5/8" round----> 5/8" square > etc......
5/8" round left, "round right
The bigger the steel the bigger the coils. You can see in the above picture how the coils in
the 5/8" round steel are much bigger than the ". The is dwarfed by the 5/8"! Both pieces
have 4 coils. The 5/8" was 7ft long and the " was just over 6ft.
Before we get into technique I want to talk about how steel bends. If youre not careful it
will bend the way it wants to. This doesnt seem to make sense until you start bending bars.
When you first begin try to control the coils so they lay next to each other or close to it. Like the
coil on the right in the above picture. This will make your bend more uniform and easier. As you
get stronger you can allow the steel to bend the way it wants. Sometimes this is more difficult
because the coils will overlap or twist making the bend much harder.
-
7/27/2019 Steel Scrolling
6/23
This is hard to explain and it is best understood after youve done some bending. The
picture below demonstrates how different a bend can be. All the pieces are 4 ft long " round
HRS. You can see that some are coiled very neatly and others are not. (The bottom right piece is
square.)
The same pieces of steel can bend very differently!
As you can see an easy 4ft bar of " round steel can do all kinds of crazy things. This isnt
a big deal as you get stronger; however, if you are inexperienced this can mean the difference
between getting that extra coil! So, as I said before, when you are starting out be sure to examine
every bend you make and study how the steel bends. Try to make it bend the way you want it to.
Youll learn a lot.
-
7/27/2019 Steel Scrolling
7/23
Heres a 5/8" x 7ft bar that didnt coil as clean as I would have liked.
Theres one more point I want to make before we go into technique; Safety! Bendingbars like this can be dangerous! Im serious. You need to be careful. Always analyze your body
positioning to ensure safety. I know your thinkin what the hell is this Hammerhead talking
about? Well Ill tell ya! If youre not paying attention the bar can slip outta your hand and
literally knock you on your ass! This is one of the reasons to practice with smaller steel like
3/8ths.
Let me give you a couple examples.......
The first time I tried this kind of bending I grabbed a piece of rebar that was lying around.
It was about " diameter and 4 ft long. I knew nothing about scrolling/coiling. I got one loop and
kept struggling with all my might. My grip slipped and the bar, which was now a spring, slammed
into my chest. It hurt like hell. I am very happy that it didnt hit my head!
My brother, a 6ft 2" 300lb monster was coiling a piece of 3/8ths. This was his first time
and I figured there would be no problem. I was wrong. He was manhandling it and trying his best.
Unfortunately, he had the bar positioned badly, and his grip slipped. The steel punched him in the
forehead and his glasses went flying.
Thank God he didnt get hit in the eye! So pay attention! If not you can take your head
off. Now I watch carefully. The last time I watched somebody coil some steel I was yellin
-
7/27/2019 Steel Scrolling
8/23
Stop!!!!!!!! over and over again. He didnt know what he was doin and was gonna knock himself
out. So the point is, if youre a knucklehead you should probably stick with tearing phone books.
The paper wont hurt you.
Technique!All right, pull out your bars, grab a towel, and put on your gloves. Its time to have fun!
Remember, weve practiced with the small stuff. Even the really small stuff that youd use for
short bending like 1/4" round and 1/4" square is great to practice with. Anyways, we got some
basics down and now were applying what we know to the big bars!
For the first set of pictures we are going to mangle some 4 ft. long x 5/8" round HRS. This
is a fun size because the bends are pretty tough compared to the smaller diameter steel.
Now this is one ugly pic.
But it shows how to start a
bend using your head! I
recommend always using a
towel. You can also start this
by pushing down over your
thigh. Another option is to
kneel on one knee and row
the bar back over the other
knee. You could also place
the bar in you mouth and bend it but Im not able to do this with 5/8" as Im writing this. One
word of caution. Dont bend Square bar in your teeth! Square bar twists as itbends. This twisting motion will probably break your teeth! Im a sissy and it was all I could do to
do this over my head. I guess I should get a neck harness and strengthen some of my weak areas!
-
7/27/2019 Steel Scrolling
9/23
Now we have a good kink in the bar that we need toincrease. Keep that towel folded up and place it in
your hip. This is important because its going to keep the end of the bar from poking through
your leg! Post and pull baby, post and puuuullll!
Heres a
position where
youll find that
you are very
powerful.
Youll notice
my hands are
not at the end of
the bar. Grab
the bar as close
to the initial bend as possible. This will make a tighter coil, and a tighter coil can mean the
difference between getting that last bend or not.
-
7/27/2019 Steel Scrolling
10/23
Ok, we bent the bar into a U. Lay it on the
ground and jam you foot in the U. Just like in the
pictures. Now post with one arm and pull like a
madman with the other! Pull the two ends as far
apart as possible.
In the picture below all Ive done is pivot the bar to
my left so I could post and pull with the opposite
arms. Do what ever feels comfortable in this
position. As you can see in these 2 pictures there is
plenty of room for my foot. This is because 5/8" isa tougher bar and makes a bigger coil. " round
bar makes a tighter coil, and if you have a big old
foot you may find it difficult to jam that monster in
there.
-
7/27/2019 Steel Scrolling
11/23
As you may have noticed, the steps
alternate between pulling and
pushing. We just finished pullingand now we need push these ends
apart until they are180 degrees
apart. (at least thats the goal)
In this picture Ive removed my
foot and placed the coil directly on
the ground. Use your thighs to
guide the ends of the bar as you
drive down. This is a good
technique when you are bending
steel bigger than " round. Youcan do this step with " round by placing a towel and the coil in your hip. (There is a pic of
Tommy doing this at the end of the article.) Its tougher but is doesnt matter. I will bent the "
round on the ground when Im tired.
This should look familiar. Time to pull again!
-
7/27/2019 Steel Scrolling
12/23
Ok, we got out 180 degrees.
Lay the bar coil up and wedgethat thing you call a foot back in
the coil. Now we are pullin
again. This picture on the right
may call for a little flexibility,
but I think most reading this
could get into a close enough
position to get it to bend.
We are now almost done. Heres a tip.
Shhhhh..... Dont tell anybody. Notice
here I have a couple of pieces of leather in
the palms of my hands. This is to provideextra padding. The less pain the better.
Youll notice as you progress in your
scrolling that your hands take a beating.
-
7/27/2019 Steel Scrolling
13/23
Lets finish it! Push with all your might!!!!!!!!!!
Now aint that purtey?
Thats one piece of freshly
cut 5/8"round HRS x 4ft
coiled for your viewing
pleasure! I guess my dogisnt impressed. Shes in the
corner snoozing away. I
wish I could be in good
shape like her just by
sleeping all day!
-
7/27/2019 Steel Scrolling
14/23
Here is an example of scrolling which most
of you would probably be able to do. Well
cut a foot off our 4ft bar. Now weve got a3ft long piece of 5/8" HRS.
In the first pic Im marking the exact center
of the bar. This little tip will help you a lot
when you want to get a coil smack dab in
the center of the bar. This probably makes
sense to a lot of you. I know there are
many of you that have marked the center of your nails and bolts to help avoid off center bends.
This is a good way to start a tougher bar. Again, I
recommend using some padding on your knee.
Remember, weve marked the center so there is no
question about placement. Just align the mark on the bar
with your knee and row the ends back.
From here on things should look familiar.
Remember to use enough padding in you hip
or you will be bruised up at best.
-
7/27/2019 Steel Scrolling
15/23
This is a crappy picture, but it
serves its purpose. Ive kept thepar in my hip. Ive got a hand on
each end of the bar and Im
pushing hard.
Remember, what I said aboutpush/pull? Well, here we go
again. You can tell, this is gettin
hard for me. I had to adjust my
grip a couple times
There we go. Huffin and
puffin with a fresh fish.
You can see here how big
the coils that 5/8'ths
makes.
-
7/27/2019 Steel Scrolling
16/23
Coiling!Over the last month Ive really gotten excited about steel coiling. Weve all read or heard
about Brookfield coiling up a 20ft steel bar. He talks about this in the GMM. Ive fallen in love
with coiling 20ft long bars. It is a total upper body workout and your grip is worked to the
upmost. The day after I coil a long bar Im sore not only in my upper body but my hands and
forearms are sore as well.
The first time I read about this I wanted to try it. Well, a good friend of mine Tommy
Heslep, a Grip Master in his own right, was itching to try to coil a 20ft long bar as well. At one
of our workouts we decided to take a little trip to my local steel supplier. We bought a couple
20ft long bars of " round HRS. We hauled them to the parking lot and went for it. We were
both very impressed with the difficulty of this. We were amazed how the whole body had to get
involved and the endurance it took to finish.
Heres a pic of that first coil that I did
with Tommy. You can see how
loose the coils are when compared to
one of my newer coils on the right.
The tighter coil took not only more
time but it took a lot more outta me!
When I was done I was sweating
bullets and suckin wind.
Dont get me wrong both were difficult; but, when the coils are made as tight as possible
the steel fights you every inch of the way. When you first try this you will understand that it is a
hard battle to keep the steel in a tight coil. My first attempt, while difficult, was relatively easy
compared to a much tighter coil.
I know, I know! Your sayin less talky, more pictures. Ok here we go.
-
7/27/2019 Steel Scrolling
17/23
Here were gonna take a look
at coiling a 20ft piece of
1/2round HRS.
Ahhhh, you gotta love visiting
you local steel supplier. Its
like a steel benders Valhalla!!!
The Bar. Now this doesnt look so intimidating.
Heres the first bend. Try to make that first bend as close
to then end of the bar as possible. This is more difficult,
but it will allow for a much tighter coil. This should look
familiar to you since the technique to start this is similar to
the previous scrolling .
-
7/27/2019 Steel Scrolling
18/23
Here, the coil is starting toemerge. This part is very tough
because there is no width to the
coil and it wants to fall over as
you coil it up. As the coil gets
wider it has more lateral
stability when you apply your
force.
Im already takin my first breather. How
does Brookfield to it so fast and tight?!?
Keep your foot on the
bar too keep the bar
from slipping around.
-
7/27/2019 Steel Scrolling
19/23
Again, I dont claim to be the best at this, and
this picture proves it! Heres another pic of me
takin a break. This is kinda like a boxer
sitting down between rounds. When you go
back and read the GMM. Brookfield writes
about how difficult coiling a 20ft bar is. He
wasnt lying!
Look at the pic! Im barely half way done! I
told my brother to take this picture because I
wanted to show how difficult this was for me.I can only hope that with practice I will be able
to duplicate this feat without taking a break to
catch my breath!
Here we go again! Youll
notice that sometimes Im
standing and other times Im
kneeling. Adjust your body
positioning whenever you
need to.
-
7/27/2019 Steel Scrolling
20/23
One more break! And the end is in sight! At this point youll notice that the coil is much wider.
This provides lateral stability while you apply force. This is very good for us; however, this is
double edged sword. Every gripster knows that the wider an object is the more demanding it
becomes on the hands. I will tell you this much, at this point my hands and forearms were
completely fried!
Almost there! Just a little over a foot left!
-
7/27/2019 Steel Scrolling
21/23
As you can see, coiling works you body at many different angles. It will also work your
hands, wrists, and forearms to their absolute limit. Remember when you first try this, that
Brookfield wasnt blowing smoke when he described the difficulty of this feat in GMM. So be
sure to warm up and stretch a bit before you start. Give it your all and you will be very pleased
with the outcome.
20ft long bar x " round HRS
Thanks to my wife Laurie and my brother Ingvar for taking all the pictures!
-
7/27/2019 Steel Scrolling
22/23
Here are a few nice scrolling pictures from fellow GripBoard members!
Heres some cool flat scrolls by Anson! (Thanks for the picbuddy!)
(Courtesy of Mark Dixon)
Heres 2 good action shots of Tommy scrolling!
Here are 2 more flat scrolls by Anson. The flat steel looks
very nice when scrolled.
-
7/27/2019 Steel Scrolling
23/23
Heres a cool pic of Eric Godfrey and one of his
scrolls. This is 3/8 round HRS x 3 ft. Look at
those tight coils!
This cool scroll is by Jonathan.
Underdawg
Good luck with your training! I hope you enjoyed this article. This article along with John
Brookfields book The Gripmasters Manuel, should help you along the road to scrolling and
coiling.
-Hammerhead Erik Vining