Thanks For Purchasing Your Kangertech Subox Mini from Us.

Following these steps will provide great satisfaction and longer use from your new E-Cigarette. Keep this manual and refer back to it when needed as the manual in your kitmay be difficult to understand.

Step 1 – Unscrew the Subtank Mini (The Tank) from theHousingAfter you have un-boxed the Kangertech SUBOX/ KBOX Mini, it will come alreadyassembled with a plastic sleeve around it for protection against scratches. Remove theplastic sleeve from the housing and unscrew the Subtank Mini from the KBOX housingunit. You can remove the Subtank by twisting counter clockwise.

Step 2 – Unscrew Subtank Mini Base with OCC (OrganicCotton Coil)Set the KBOX housing to the side and unscrew the atomizer base and the OCC coilfrom the tank Subtank housing.

Step 3 – Soak the OCC (Organic Cotton Coil) in both exposedAir HolesYou want to start by priming or soaking the OCC coil in both exposed air holes to allowe juice to completely soak into the cotton. Take an e juice dropper to drop a single dripof e juice in both holes, one at a time, letting each single drop completely soaking inbefore another drop is made. Once you have multiple drips on both sides of the OCCcoil, you want to make sure the e juice is completely soaked into the cotton before thenext step.

Step 4 – Soak OCC (Organic Cotton Coils) in Center Tube –FROM THE SIDEThis is not a required step, but priming the atomizer by slightly soaking the center tubefrom the side, does allow the e juice to better soak into the OCC coil. It is very importantin this step to not over soak the center tube as this will cause leaking, gurgling or even aleaking tank. What you want to do is take one drop at a time on the edge of the centertube to soak the cotton. You will only need about 2-3 drops of e juice to completely soakthe cotton within the coil unit.

Step 5 – Let your Organic Cotton Coil sit and soak for about 10Minutes

Step 6 – Fill the Subtank Mini Tank to the Black Fill Line(Pictured Below)

Step 7 – Screw Base back on the Subtank Mini TankThe image below is an example of different settings to adjust air flow. This is one areawhere the SUBOX/ KBOX mini really stands out from the rest of the Kanger Box Mods.The adjustable airflow is the best feature of this mod as you can choose how muchvapor you want the unit to produce.

Step 7a – Adjust air flow slot on the Subtank MiniNote: Adjustable Air Flow To Wide or Narrow To Suit Your Own Preference by

rotating the bottom of tank back & forth to desired width.

Step 8 – Screw Subtank Mini back onto Kanger SUBOX / KBOXMini housing

Step 9 – Open the IMR Battery Housing/ Magnetic Latch

Step 10 – Insert IMR Battery into Housing of Kanger SUBOX /KBOX Mini

Important Note: Insert Battery As Shown (+) to Positive & (-) to Negative.Step 11 – Connect the IMR Battery Magnetic Latch

Step 12 – The Kanger SUBOX / KBOX Mini Controls1. ON/ OFF: 5 fast clicks on fire button2. +/- Button: Control Adjustable Wattage3. OLED Display: Battery Level, Resistance and Output Wattage4. Adjust Display: Hold +/- Button at the Same Time

Always start with a low wattage setting 20W as you use the unit. Increase the wattageaccordingly.

Tips:

The amount of vape will diminish as the battery output power lessons. Recharge batteryor re-insert a fully charged 18650 IMR spare battery.

If Vape Diminishes and your tank is full of e-juice and the battery is fully charged,replace the atomizer following the procedures above.

If you get a burned taste, your atomizer needs replacing, this is usually caused by dryvaping or atomizer heat damage, Atomizer replacement is the only remedy.