stopowerwall detail booklet - sto corp
TRANSCRIPT
®
StoPowerwall
CommercialDetail BookletSeries 4s.xx | November 2021
®Facades
Stucco Systems
StoPowerwall® is a stuccowall assembly withcontinuous air and moisturebarrier and moisture drainage. It combines the strength and durability of traditional stucco with StoGuard® moisture protection and Sto high performance finishes.
StoPowerwall® can be used in residential or commercial wall construction.
ATTENTION
The final design of any project is the sole responsibility of the Design Professional, with considerations for compliance with local building and design codes and requirements.Sto Corp. accepts no liability for design, engineering, or workmanship of any project.The information provided herein is in addition to other technical data provided by Sto Corp. (System Bulletin, Specification, Guide Details, etc). For more information, please visit www.stocorp.com
3800 Camp Creek Pkwy. SWBldg. 1400 • Suite 120Atlanta, GA 30331Tel: (800) 221-2397Fax: (404) 346-3119http://www.stocorp.comhelpdesk.stocorp.com
Sto Corp.
StoPowerwall®
Table of Contents
Design Details
2
Components System Components ........................................................................................................................................................ 4.01 System Components with StoCast Brick ............................................................................................................................ 4.01 SCB System Components with StoCast Wood ........................................................................................................................... 4.01 SCW System Components with Sto Crack Defense System over Concrete/CMU - w/o Air & Moisture Barrier ................................ 4.01 CMU System Components with MVES (Masonry Veneer Engineered System) ................................................................................4.01 MVES StoCreativ® Brick Finish .................................................................................................................................................... 4.05 StoGuard® Components .................................................................................................................................................... 4.09
Installation at Grade Termination at Grade: Sidewalk/Pavers .............................................................................................................................. 4.10 Termination at Balcony .................................................................................................................................................... 4.12
Installation at Windows Commercial Window Head ............................................................................................................................................... 4.20 Commercial Window Sill ................................................................................................................................................... 4.22 Stucco/Brick/Window Interface ......................................................................................................................................... 4.28 Installation at Joints Floor Line Joint with Nested Track ..................................................................................................................................... 4.50 One-Piece Control Joint .................................................................................................................................................... 4.52 One-Piece Expansion Joint .................................................................................................................................................4.52 A Two-Piece Expansion Joint ................................................................................................................................................ 4.52 B Joint at Inside Corner: Different Substrates ........................................................................................................................ 4.53
Installation at Corners Inside Corner: Common Substrate ..................................................................................................................................... 4.54 Outside Corner ................................................................................................................................................................. 4.55
Installation at Corners CMU/Steel Frame Junction ................................................................................................................................................ 4.58
Installation at Parapet, Saddle Flashing and Buildouts Termination at Parapet Cap .............................................................................................................................................. 4.60 Saddle Flashing Assembly ................................................................................................................................................ 4.64 Saddle Flashing ................................................................................................................................................................ 4.65 Buildouts ......................................................................................................................................................................... 4.70
R
www.stocorp.com
Date:December 2015
Notes:
StoPowerwall®
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto's instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building compo-nents or assemblies, or for other construction activities beyond Sto's control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or build-ing may result in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPTFOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO'S WARRANTY PROGRAMS WHICH ARE SUB-JECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
Attention
Property of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identified asSto are furnished by other manufacturersand are not necessarily installed by tradeswho install the Sto products. Refer to proj-ect specific contract documents.
ComponentsDetail No.: 4.01
Detail shows theinstallation ofStoPowerwall Stuccoover a steel frame wall intwo coats.
Sto materials:
1] StoGuard® with StoEmeraldCoat®
2] StoPowerwall scratchcoat
3] Sto Powerwall browncoat
4] Sto Hot Prime® or StoPrimer
5] Sto finish (smooth ortextured)
Accessory materialsincluding means forfastening:
1] Expanded metal lath2] Casing bead3] Other accessories as
may be required (e.g.weep screeds, etc.)
Structure
Sheathing
Sto EmeraldCoat®
Code compliant paperor felt water-resistivebarrier (WRB)
Casing bead
Expanded metal lath
StoPowerwall scratchcoat
StoPowerwall browncoat
Sto primer
Sto finish (smooth ortextured)
Sto Powerwall® with StoCast Brick Detail No.: 4.01 SCBDate: November 2021
StoGuard®
Air & Moisture Barrier(See Note 1)
Water Resistive Barrier (WRB), Code Compliant Paper or Felt WRB
Metal Lath(See Note 3)
Sto Powerwall®
Scratch Coat(See Note 4)
Sto Powerwall®
Brown Coat(See Note 4)
Sto Bonding & PointingMortar(See Note 5)
StoCast Brick(See Note 5)
Sto Bonding & PointingMortar(See Note 5)
Notes:
1. See StoGuard Chart (22s.SG) for transition component, joint treatment, and rough opening protection product options.
2. Glass mat gypsum sheath-ing in compliance with ASTM C1177, exterior grade and Exposure 1 wood based sheathing, or cementitious sheathing in compliance with ASTM C1325.
3. Minimum 2.5 lb/yd2 (1.4 kg/m2) self-furred galvanized diamond mesh metal lath.
4. Stucco scratch and brown coat material in compliance with ASTM C926 and manufactured or listed by Sto Corp.
5. Refer to the StoCast Brick Application Guide for more information.
6. Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
Metal FrameSheathing(See Note 2)
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Sto Powerwall® with StoCast Wood Detail No.: 4.01 SCWDate: November 2021
StoGuard®
Air & Moisture Barrier(See Note 1)
Water Resistive Barrier (WRB), Code Compliant Paper or Felt WRB
Metal Lath(See Note 3)
Sto Powerwall®
Scratch Coat(See Note 4)
Sto Powerwall®
Brown Coat(See Note 4)
StoCast Wood Adhesive(See Note 5)
StoCast Wood(See Note 5)
StoColor® Wood Stain(See Note 5)
Notes:
1. See StoGuard Chart (22s.SG) for transition component, joint treatment, and rough opening protection product options.
2. Glass mat gypsum sheath-ing in compliance with ASTM C1177, exterior grade and Exposure 1 wood based sheathing, or cementitious sheathing in compliance with ASTM C1325.
3. Minimum 2.5 lb/yd2 (1.4 kg/m2) self-furred galvanized diamond mesh metal lath.
4. Stucco scratch and brown coat material in compliance with ASTM C926 and manufactured or listed by Sto Corp.
5. Refer to the StoCast Wood Application Guide for more information.
6. Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
Metal FrameSheathing(See Note 2)
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Sto Powerwall® with Sto Crack Defense SystemSystem Components on Concrete or CMU
Detail No.: 4.01 CMUDate: November 2021
StoPowerwall®
Scratch Coat(See Note 2)
StoPowerwall®
Brown Coat(See Note 2)
Sto Crack Defense:Sto Basecoat with Sto Mesh embedded
Sto Primer
Sto Textured Finish
Notes:
1. Sto Components:
a. Sto Powerwall® Scratch Coat
b. StoPowerwall® Brown Coat
c. Sto Crack Defense: Sto Basecoat with Sto Mesh embedded.
d. Sto Primer
e. Sto Textured Finish Coat
2. Stucco Scratch and Brown Coat material in compliance with ASTM C926 and manufactured or listed by Sto Corp.
3. Construct a site built mock-up using materials and sub-trades associated with the project to verify installation sequencing, detailing, and aesthetics.
4. Refer to applicable Sto guide specifications, product bulletins, Tech Hotlines, and other Sto guide details for additional information.
5. Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
Concrete or CMU
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Sto Powerwall® MVES
ComponentsDetail No.: 4.01 MVESDate: December 2020
StoGuard®
Air & Moisture Barrier(See Note 1)
Water Resistive Barrier (WRB), Code Compliant Paper or Felt WRB
Metal Lath(See Note 3)
Stucco Scratch andBrown Coat(See Note 4)
StoColl KMAdhesive Mortar
Masonry Veneer(See Note 5)
Masonry Veneer Grout(See Note 6)
Notes:
1. See StoGuard Chart (22s.SG) for transition component, joint treatment, and rough opening protection product options.
2. Glass mat gypsum sheath-ing in compliance with ASTM C1177, exterior grade and Exposure 1 wood based sheathing, or cementitious sheathing in compliance with ASTM C1325.
3. Minimum 2.5 lb/yd2 (1.4 kg/m2) self-furred galvanized diamond mesh metal lath.
4. Stucco scratch and brown coat material in compliance with ASTM C926 and manufactured or listed by Sto Corp.
5. Veneer options: thin brick, thin stone, ceramic tile or cultured stone in conformance with applicable building code requirements.
6. Portland cement-based grout / pointing mortar in compliance with ANSI 118.7
7. Components not identified as Sto are furnished by other manufacturers and are not necessarily installed by trades who install the Sto products. Refer to project specific contract documents.
Metal FrameSheathing(See Note 2)
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
R
www.stocorp.com
Date:December 2015
Notes:
StoPowerwall®
Property of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identified asSto are furnished by other manufacturersand are not necessarily installed by tradeswho install the Sto products. Refer to proj-ect specific contract documents.
StoCreativ® Brick FinishDetail No.: 4.05
Step 11] Install StoPowerwall
stucco [Refer to StoDetail 4.01].
2] Install Sto PrimerCreativ over the StoPowerwall base coat.
3] Optional: Apply asecond application ofSto Primer Creativ toprovide a slightlyuneven color to simu-late variablemortar color.
Step 24] Apply the Sto brick
template to the dryprimer.
Step 35] Install appropriate Sto
finish to match theCreativ Brick texturespecified. Refer toSto Creativ BrickSpecification A100 FF
Step 46] Remove the template
before the finish dries.7] Optional: After the fin-
ish dries, touch up thefinish with StoCoat®Acryl or StoTique® incolors and pattern tomatch approved sam-ple.
Step 1
StoPowerwall Stucco
Sto PrimerCreativ
Step 2
Sto brick template
Step 3
Sto finish
Step 4
Template removed
Finish touch-up
Step 1
Step 2
Step 3
Step 4
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto's instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building compo-nents or assemblies, or for other construction activities beyond Sto's control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or build-ing may result in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPTFOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO'S WARRANTY PROGRAMS WHICH ARE SUB-JECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
Attention
R
www.stocorp.com
Date: November 2015
Notes:
SSttooPPoowweerrwwaallll®
Attention
SSttooGGuuaarrdd® CCoommppoonneennttssDetail No.: 4.09
StoGuard detailcomponent (see tablebelow for StoGuardproduct options)
StoGuard® sheathing jointtreatment (see table belowfor StoGuard productoptions)
Rough OpeningTreatment (see tablebelow for StoGuardproduct options)
Sto EmeraldCoat®
Property of Sto Corp.All Rights Reserved.
IMPORTANT: Components not identified as Sto arefurnished by other manufacturers and are not nec-essarily installed by trades who install the Sto prod-ucts. Refer to project specific contract documents.
StoGuard® Components for use with StoPowerwall®
Product or Product CombinationSheathing
JointRough
OpeningDetail
Component
StoGuard RapidFill
StoGuard RapidSeal
StoGuard Fabric embedded in Sto Emerald CoatStoGuard Transition Membrane embedded inStoGuard RapidFill, StoGuard RapidSeal orSto Emerald Coat
Sto Gold Fill with StoGuard Mesh orSto Detail Mesh
StoGuard Tape
1] Refer to Sto detail series20.xx or 21.xx for completeinstructions regardingmaterial options andapplication instructions forStoGuard products.
2] Flashing must be installed atthe head and sill of windowopenings and integrated intothe StoGuard system withStoGuard detail components.
3] The upper edge of StoGuardTape must be lapped with aStoGuard detail componentto direct water away from thesubstrate.
4] Refer to StoGuard TransitionMembrane installation guidefor step-by-step instructionsfor detailing with StoGuardTransition Membrane.
5] Refer to the individual Stoproduct bulletin andapplicable Sto specificationfor the products being used.
6] Refer to the most current Stoproduct bulletins,specifications, installationguides and other informationare available atwww.stocorp.com.
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto‘s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building compo-nents or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or build-ing may result in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPTFOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO‘S WARRANTY PROGRAMS WHICH ARE SUB-JECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
R
Date:December 2015
Notes:
Sto Powerwall®
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto's instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building compo-nents or assemblies, or for other construction activities beyond Sto's control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or build-ing may result in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPTFOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO'S WARRANTY PROGRAMS WHICH ARE SUB-JECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
Attention www.stocorp.com
Termination at Grade: Sidewalk / PaversDetail No.: 4.10
1] Install barriermembrane at bottom offrame wall to provideprotection from rainpenetration below thestucco.
2] Install stucco weepscreed or flashing toterminate minimum 1“(25 mm) below sill plate .
3] Provide minimum 2" (50mm) clearance betweennose of weep screed andsidewalk / pavedsurface. Increasedistance when snow andice may accumulate
4] Lap StoGuard® detailcomponent onto weepscreed to direct water tothe exterior. See Stodetail 4.09
5] Provide waterproofing atthe foundation to protectthe support structure from
rising damp.
Structure
Sheathing
Sto EmeraldCoat®
Code Compliant paperor felt water-resistivebarrier (WRB)
Expanded metal lath
StoPowerwall scratchcoat
StoPowerwall browncoat
Sto primer
Sto finish (smooth ortextured)
StoGuard® detail com-ponent (note 4)
Weep screed orflashing
Barrier membrane
Sidewalk / Pavers
Foundation water-proofing
Property of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identified asSto are furnished by other manufacturersand are not necessarily installed by tradeswho install the Sto products. Refer to proj-ect specific contract documents.
R
www.stocorp.com
Date:December 2015
Notes:
StoPowerwall®
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto's instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building compo-nents or assemblies, or for other construction activities beyond Sto's control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or build-ing may result in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPTFOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO'S WARRANTY PROGRAMS WHICH ARE SUB-JECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
Attention
Termination at BalconyDetail No.: 4.12
1] Provide continuity ofwater protection at thewall / deck interface.
2] Provide clearancebetween the underside ofthe stucco and the deckto allow adequatedrainage.
3] Refer to Sto Detail 4.45for termination and drain-age at the edge of thefloor slab.
4] Lap StoGuard® Detailcomponent onto weepscreed to direct water tothe exterior. See Stodetail 4.09.
Structure
Sheathing
Sto EmeraldCoat®
Code Compliant paperor felt water-resistivebarrier (WRB)
Expanded metal lath
StoPowerwall stucco
Sto primer
Sto finish (smooth ortextured)
StoGuard® detail com-ponent (note 4)
Deck waterproofinglapped behind flashingor weep screed
Flashing or weepscreed
Backer rod andsealant
Deck
Property of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identified asSto are furnished by other manufacturersand are not necessarily installed by tradeswho install the Sto products. Refer to proj-ect specific contract documents.
R
www.stocorp.com
Date:December 2015
Notes:
StoPowerwall®
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto's instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building componentsor assemblies, or for other construction activities beyond Sto's control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building mayresult in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPT FOREXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO'S WARRANTY PROGRAMS WHICH ARE SUBJECTTO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
Attention
Commercial Window HeadDetail No.: 4.20
1] Provide a mock-upinstallation and testusing materials andsubstrates associatedwith the project.
2] Provide flashing installedover the window to directwater away from thewindow. Verify require-ments for head flashingwith local codes and win-dow manufacturer.
3] Protect roughopening against waterpenetration by wrappingwith Sto Guard®. Directany water penetration tothe exterior at or abovethe sill pan flashing.
(Refer to Sto detail 4.09)
4] Provide continuous airbarrier connectionaround the perimeter ofthe window to reduceleaking, condensationrelated to air movementand sound and insectintrusion.
5] Provide window insert tooptimize sealant configu-ration.
Sheathing
Sto Detail Component(see Sto Detail 4.09)
Head flashing
Drainage accessory
Air seal aroundwindow perimeter
Window
Sto finish (smooth ortextured)
Closed cell backer-rodand sealant
Sto primer
StoPowerwall stucco
Expanded metal lath
Casing bead
Code compliant paperor felt water-resistivebarrier (WRB)
Sto EmeraldCoat®
StoGuard® roughopening treatment(Sto Detail 4.09)
Supporting structureProperty of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identified asSto are furnished by other manufacturersand are not necessarily installed by tradeswho install the Sto products. Refer to proj-ect specific contract documents.
R
www.stocorp.com
Date:December 2015
Notes:
StoPowerwall®
Property of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identified asSto are furnished by other manufacturersand are not necessarily installed by tradeswho install the Sto products. Refer to proj-ect specific contract documents.
Commercial Window SillDetail No.: 4.22
1] Provide a mock-upinstallation and test usingmaterials and substratesassociated with the project.
2] Prepare opening prior to theinstallation of the window.Coordinate installation withother associated substrates.
3] Provide StoGuard®
air/moisture barrier and otherassociated trim and accesso-ries as noted in Sto detail4.09.
4] Provide pan flashing at sill todrain water to the exterior.
5] In cold climates this detail willprovide little insulationaround the pan flashing. Thedesigner should specify apan design that will providea thermal break.
6] Provide continuous air barrierconnection around perimeterof the window to reduce leak-ing, condensation related toair movement,sound, andinsect intrusion.
Structural support
Sheathing
Sto rough openingtreatment (see StoDetail 4.09)
Sto EmeraldCoat®
Code compliant paperor felt water-resistivebarrier (WRB)
Expanded metal lath
Casing bead
StoPowerwall stucco
Sto primer
Sto finish (smooth ortextured)
Closed cell backer-rodand sealant
StoGuard® lapped intopan flashing
Air seal continuousaround interiorperimeter ofwindow
Window
Pan flashing
Sealant gasket
Sill wedge
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto's instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building compo-nents or assemblies, or for other construction activities beyond Sto's control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or build-ing may result in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPTFOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO'S WARRANTY PROGRAMS WHICH ARE SUB-JECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
Attention
R
www.stocorp.com
Date:December 2015
Notes:
StoPowerwall®
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto's instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building compo-nents or assemblies, or for other construction activities beyond Sto's control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or build-ing may result in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPTFOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO'S WARRANTY PROGRAMS WHICH ARE SUB-JECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
Attention
Property of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identified asSto are furnished by other manufacturersand are not necessarily installed by tradeswho install the Sto products. Refer to proj-ect specific contract documents.
Stucco/Brick/Window InterfaceDetail No.: 4.28
1] Provide a mock-upinstallation and test usingmaterials and subtradesassociated with the project.
2] Prepare opening prior to theinstallation of the window.Integrate flashing to drain tothe exterior as recommend-ed by the Brick Industry ofAmerica*.
3] Provide moisture barrier andother associated trim andaccessories as noted in Stodetail 4.01.
4] In cold climates the flashingdepicted could create a ther-mal bridge. In those casesprovide a thermal breakbetween sill flashing andinterior.
5] Maintain continuity of weath-er barrier behind claddings.
6] Flash StoPowerwallstucco termination to drainwater away from brick cavity.
* BIA Technical Notes 7 -Water Resistance of BrickMasonry, Design and Detail-ing Part 1 Feb. 1985 (April2001)
Supporting structure
Sheathing
StoGuard® wrappedinto opening (See StoDetail 4.09)
Code compliant paperor felt water-resistivebarrier (WRB)
Sto EmeraldCoat®
Air seal
Casing bead
Window
Casing bead withweeps
Flashing
Brick sill
Sill flashing
Brick Tie
R
www.stocorp.com
Date:December 2015
Notes:
StoPowerwall®
Property of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identified asSto are furnished by other manufacturersand are not necessarily installed by tradeswho install the Sto products. Refer to proj-ect specific contract documents.
Floor Line Joint with Nested TrackDetail No.: 4.50
1] Do not attach uppersheathing to nestedtrack. Only attachlower sheathing tonested track.
2] The maximumallowable sheathingspan at the floor line is8“ (200mm) or as rec-ommended by thesheathingmanufacturer.
3] A barrier membrane isinstalled over the jointin the sheathing toprovide air barrier con-tinuity and secondaryweather protection atthe joint location.
4] Provide a minimum3/4” (20mm) joint toaccommodatedeflection of the floorslab.
5] Install a flashing todirect water beyondthe face of thecladding below.
Structure
Sheathing
Sto EmeraldCoat®
Code compliant paperor felt water-resistivebarrier (WRB)
Expanded metal lath
StoPowerwall stucco
Sto primer
Sto finish (smooth ortextured)
Sto detail component(refer to Sto Detail4.09)
Weep Screed
Flashing
Barrier membrane
Backer rod
Backer rod andsealant
Casing bead
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto's instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building compo-nents or assemblies, or for other construction activities beyond Sto's control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or build-ing may result in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPTFOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO'S WARRANTY PROGRAMS WHICH ARE SUB-JECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
Attention
R
www.stocorp.com
Date: December 2015
Notes:
StoPowerwall®
Property of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identifiedas Sto are furnished by other manufactur-ers and are not necessarily installed bytrades who install the Sto products. Referto project specific contract documents.
One-Piece Control JointDetail No.: 4.52
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto's instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building compo-nents or assemblies, or for other construction activities beyond Sto's control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or build-ing may result in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPTFOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO'S WARRANTY PROGRAMS WHICH ARE SUB-JECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
Attention
.
Sheathing
Sto
Code Compliant paperor felt water-resistivebarrier (WRB)
Stucco
Sto Primer
Sto Finish (smooth ortextured)
Joint accessory
Expanded metal lath.DISCONTINUOUSBENEATH JOINTACCESSORY
1] Provide one-piece control joints at mini-mum 144 ft² (13.4 m²)intervals and belowwindow, door, andsimilar openings in thewall construction.
2] Do not exceed lengthto width ratio of 2.5:1in joint layout and donot exceed 18 ft (5.5m) in any directionwithout a joint.
3] Lap metal reinforce-ment (lath) over jointaccessory flanges andwire tie. Alternatively,install metal reinforce-ment, snip (cut) at lineof accessory, and wiretie joint accessoryover metal reinforce-ment. Metal reinforce-ment MUST BE DIS-CONTINUOUSBENEATH THEACCESSORY.
4] Comply with ASTM1063.
R
www.stocorp.com
Date:December 2015
Notes:
StoPowerwall®
Property of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identified asSto are furnished by other manufacturersand are not necessarily installed by tradeswho install the Sto products. Refer to proj-ect specific contract documents.
One-Piece Expansion JointDetail No.: 4.52a
1] Provide expansion jointswhere movement instucco or substrate isanticipated:• at floor lines,• at dissimilar construction
materials,• at existing building or expan-sion joints in the construction,• at changes in building height,• at columns or
cantilevered areas,• at maximum 144 ft2 (13.4 m2)intervals
2] Do not exceed length towidth ratio of 2.5:1 in expan-sion joint layout and do notexceed more than 18‘(5.5m) in any direction with-out an expansion joint.
3] Provide barriermembrane over the joint inthe sheathing to maintainwaterproofing/air barrierintegrity. Support with aclosed cell backer rod.
4] Provide one piece expan-sion joint accessory over themoisture barrier and lap theexpanded metal lath overthe flanges. Metal lath mustbe discontinuous at theexpansion joint.
5] Comply with ASTM 1063.
Structure
Sheathing
Sto EmeraldCoat®
Closed cell backer rod
StoGuard® TransitionMembrane embeddedin Sto EmeraldCoat orStoGuard Rapid Seal
Code compliant paperor felt water-resistivebarrier (WRB)
Expanded metal lath
Expansion jointaccessory
StoPowerwall Stucco
Sto primer
Sto finish (smooth ortextured)
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto's instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building compo-nents or assemblies, or for other construction activities beyond Sto's control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or build-ing may result in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPTFOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO'S WARRANTY PROGRAMS WHICH ARE SUB-JECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
Attention
R
www.stocorp.com
Date: December 2015
Notes:
StoPowerwall®
Property of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identified asSto are furnished by other manufacturersand are not necessarily installed by tradeswho install the Sto products. Refer to proj-ect specific contract documents.
Two-Piece Expansion JointDetail No.: 4.52b
1] Provide expansion jointswhere movement instucco or substrate isanticipated:• at floor lines,• at dissimilar construction
materials,• at existing building or expan-sion joints in the construction,• at changes in building height,• at columns or
cantilevered areas,• at maximum 144 ft2 (13.4 m2)intervals
2] Do not exceed length towidth ratio of 2.5:1 in expan-sion joint layout and do notexceed more than 18‘(5.5m) in any direction with-out an expansion joint.
3] Provide barriermembrane over the joint inthe sheathing to maintainwaterproofing/air barrierintegrity. Support with aclosed cell backer rod.
4] Provide back-to-back casingbeads or two piece expan-sion joint accessory over themoisture barrier and lap theexpanded metal lath overthe flanges. Metal lath mustbe discontinuous at theexpansion joint.
5] Provide backer rod andsealant between the casingbeads.
6] Comply with ASTM 1063.
Structure
Sheathing
Sto EmeraldCoat®
Closed cell backer rod
StoGuard® TransitionMembrane embeddedin Sto EmeraldCoat orStoGuard Rapid Seal
Code compliant paperor felt water-resistivebarrier (WRB)
Expanded metal lath
Casing bead
StoPowerwall™ Stucco
Sto primer
Sto finish (smooth ortextured)
Closed cell backer rod
Sealant
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto's instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building compo-nents or assemblies, or for other construction activities beyond Sto's control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or build-ing may result in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPTFOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO'S WARRANTY PROGRAMS WHICH ARE SUB-JECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
Attention
R
www.stocorp.com
Date:December 2015
Notes:
StoPowerwall®
Property of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identified asSto are furnished by other manufacturersand are not necessarily installed by tradeswho install the Sto products. Refer to proj-ect specific contract documents.
Joint at Inside Corner: Different SubstratesDetail No.: 4.53
1] Install Sto joint treatmentapproximately 4“(100mm) onto each face.Refer to Sto Detail 4.09.(StoGuard® Mesh is notrecommended overmasonry substrate.) Donot extend StoGuard onCMU beyond theexpanded flange of theaccessory.
2] Apply Sto EmeraldCoat®
over sheathing sub-strate.
3] Inside corner joints arenot recommended wherethe substrateconstruction on eitherside of the corner is thesame.
4] StoPowerwall Stuccoapplied directly to CMUfunctions as a water andair resistant assembly.
Concrete masonry
Steel frame
Sheathing
Sto joint treatment(see Sto Detail 4.09)
Sto EmeraldCoat®
Code compliant paperor felt water resistivebarrier (WRB)
Expansion joint
Expanded metal lath
StoPowerwall stucco
Sto primer
Sto finish (smooth ortextured)
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto's instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building compo-nents or assemblies, or for other construction activities beyond Sto's control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or build-ing may result in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPTFOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO'S WARRANTY PROGRAMS WHICH ARE SUB-JECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
Attention
R
www.stocorp.com
Date:December 2015
Notes:
StoPowerwall®
Property of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identified asSto are furnished by other manufacturersand are not necessarily installed by tradeswho install the Sto products. Refer to proj-ect specific contract documents.
Inside Corner: Common SubstrateDetail No.: 4.54
1] Install StoGuard® jointtreatment minimum 4“(100 mm) onto eachface of inside cornerand trowel Sto jointtreatment over themesh. Refer to StoDetail 4.09.
2] Apply StoEmeraldCoat® tosheathing substrate.
3] Inside corner jointsare not recommendedwhere the substrateconstruction on eitherside of the corner isthe same.
Structure
Sheathing
Sto joint treatment(See Sto Detail 4.09)
Sto EmeraldCoat®
Code compliant paperor felt water-resistivebarrier (WRB)
Expanded metal lath
StoPowerwall stucco
Sto primer
Sto finish (smooth ortextured)
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto's instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building compo-nents or assemblies, or for other construction activities beyond Sto's control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or build-ing may result in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPTFOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO'S WARRANTY PROGRAMS WHICH ARE SUB-JECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
Attention
R
www.stocorp.com
Date:December 2015
Notes:
StoPowerwall®
Property of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identified asSto are furnished by other manufacturersand are not necessarily installed by tradeswho install the Sto products. Refer to proj-ect specific contract documents.
Outside CornerDetail No.: 4.55
1] Install expanded metallath continuousaround corner withoutbreak for minimum 24”(610 mm).
2] Attach corner beadover lath.
3] Metal accessories aresusceptible tocorrosion in costalenvironments. Metalcorner beads withsolid metal nosesare susceptible to cor-rosion in exposedexterior application.
4] Comply with ASTM 1063.
Structure
Sheathing
Sto joint treatment(see Sto Detail 4.09)
Sto EmeraldCoat®
Code compliant paperor felt water-resistivebarrier (WRB).
Expanded metal lath
Corner reinforcing
StoPowerwall stucco
Sto primer
Sto finish (smooth ortextured)
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto's instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building compo-nents or assemblies, or for other construction activities beyond Sto's control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or build-ing may result in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPTFOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO'S WARRANTY PROGRAMS WHICH ARE SUB-JECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
Attention
R
www.stocorp.com
Date:December 2015
Notes:
StoPowerwall®
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto's instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building compo-nents or assemblies, or for other construction activities beyond Sto's control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or build-ing may result in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPTFOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO'S WARRANTY PROGRAMS WHICH ARE SUB-JECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
Attention
Property of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identified asSto are furnished by other manufacturersand are not necessarily installed by tradeswho install the Sto products. Refer to proj-ect specific contract documents.
CMU/Steel Frame JunctionDetail No.: 4.58
1] Provide a drained jointat the interface offrame and masonrysubstrates.
2] Protect the steelframe from the poten-tial of rising dampwithin the concretemasonry units.
3] Do not extendbarrier membrane onCMU beyond theexpanded flange ofthe accessory.
Structure
Sheathing
Sto EmeraldCoat®
Code compliant paperor felt water-resistivebarrier (WRB)
Expanded metal lath
StoPowerwall stucco
Sto detail component(see Sto Detail 4.09)
Flashing
Weep Screed
StoGuard TransitionMembrane emeddedin Sto EmeraldCoat orStoGuard® RapidSeal
Casing bead
Backer rod
Barrier membrane
Sto primer
Sto finish (smooth ortextured)
R
www.stocorp.com
Date:December 2015
Notes:
StoPowerwall®
Property of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identified asSto are furnished by other manufacturersand are not necessarily installed by tradeswho install the Sto products. Refer to proj-ect specific contract documents.
Termination at Parapet CapDetail No.: 4.60
1] Install StoGuard®
System over theparapet supportingstructure lapping ontocompatible sheathing.
2] Provide a barriermembrane over theparapet blocking andintegrate it with theroofing or deck water-proofing assembly.This provides addition-al protection againstwater intrusionthrough penetration ofmechanical fasteners.
3] Parapet illustratedis uninsulated.Conditioned interior airshould not circulate inthis space if there is arisk of condensation.
4] Provide a minimum 3"(75 mm) overlap offlashing over the faceof the stucco.Increase overlap withbuilding height.
Cap flashing
Roof membrane
Blocking
StoGuard detail com-ponent (see Sto Detail4.09)
Casing bead
Sealant
Sto EmeraldCoat®
Code compliant paperor felt water-resistivebarrier (WRB)
Expanded metal lath
StoPowerwall stucco
Sto primer
Sto finish (smooth ortextured)
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto's instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building compo-nents or assemblies, or for other construction activities beyond Sto's control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or build-ing may result in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPTFOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO'S WARRANTY PROGRAMS WHICH ARE SUB-JECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
Attention
R
www.stocorp.com
Date:December 2015
Notes:
StoPowerwall®
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto's instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building compo-nents or assemblies, or for other construction activities beyond Sto's control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or build-ing may result in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPTFOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO'S WARRANTY PROGRAMS WHICH ARE SUB-JECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
Attention
Property of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identified asSto are furnished by other manufacturersand are not necessarily installed by tradeswho install the Sto products. Refer to proj-ect specific contract documents.
Step 1C
A
B
Step 2
Step 3
Saddle Flashing AssemblyDetail No.: 4.64
1] Pieces ‘A’ and ‘B’ arefolded as shown andare mirror images ofeach other. The flat topportions are designedto overlap over thelower parapet wall andflat against the higherwall. The turnouts areto match the thicknessof the stucco plus 1/4“(6 mm) so water willdrain beyond thestucco finish.
2] Piece ‘C’ is designed tostraddle the parapetwall. The upturnedflange is placed behindthe flat flanges of ‘A’and ‘B’ and the twodown- turned legs inter-lock over the lower por-tions of ‘A’ and ‘B’ in ashingle fashion.
3] The assembled piecesare installed againstStoGuard® air/moisturebarrier and into asealant gasket.
4] Install Sto jointtreatment and StoEmeraldCoat® over thetop flanges to ensuredrainage to the exteriorof the cladding.
5] Provide StoPowerwallStucco as shown in Stodetail 4.65.
Turn out flanges tomatch thickness ofstucco plus 1/4“(6mm)
Flashing assembledover StoGuard®
Waterproofing/AirBarrier
Parapet
Install Sto jointtreatment (see StoDetail 4.09) over upperflanges of the flashing
R
www.stocorp.com
Date:December 2015
Notes:
StoPowerwall®
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto's instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building compo-nents or assemblies, or for other construction activities beyond Sto's control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or build-ing may result in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPTFOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO'S WARRANTY PROGRAMS WHICH ARE SUB-JECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
Attention
Property of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identified asSto are furnished by other manufacturersand are not necessarily installed by tradeswho install the Sto products. Refer to proj-ect specific contract documents.
Saddle FlashingDetail No.: 4.65
1] Install StoPowerwallstucco over StoGuard®
air/moisture barrier(see Sto detail 4.01).
2] Lap stucco over theflashing assembly atthe top by aminimum of 2“(50mm)and terminate with1/2” (13mm) jointaround the perimeter.
3] Refer to Sto Detail4.64 for assembly ofsaddle flashing.
4] Provide parapet capflashing. (Refer toSto detail 4.60 fortermination at aparapet cap flashing.
Structure
Sheathing
Code compliant paperor felt water-resistivebarrier (WRB)
Sto EmeraldCoat®
Expanded metal lath
StoPowerwall stucco
Sto primer
Sto finish (smooth ortextured)
Flashing or weepscreed
Saddle flashingassembly (see StoDetail 4.64)
Sto joint treatment(see Sto Detail 4.09)
Casing bead
Backer rod andsealant installedbetween casing beadand flashing
StoPowerwall stucco
R
www.stocorp.com
Date:December 2015
Notes:
StoPowerwall®
Property of Sto Corp. All Rights Reserved.
IMPORTANT: Components not identified asSto are furnished by other manufacturersand are not necessarily installed by tradeswho install the Sto products. Refer to proj-ect specific contract documents.
BuildoutsDetail No.: 4.70
1] Install foam shapes overStoPowerwall stucco usingSto adhesive.
2] Cover the shapes with Stobase coat and reinforcingmesh lapping onto the faceof the stucco a minimum of2.5" (65 mm).
3] The exposed surface musthave a minimum slope of1:2 (27°). In locationswhere ice and snow mayaccumulate increase slope.
4] Provide Sto Flexyl andmesh on upper surfaces ofbuildouts projecting morethan 2” (50 mm) from thestucco surface lapping overthe base coat and stucco toprovide a weather tight seal.
5] Consult local building coderequirements for maximumallowable foam thickness
6] Apply Sto Primer over allsurfaces to provide a uni-form color base for the Stofinish.
Structure
Sheathing
Sto joint treatment(see Sto Detail 4.09)
Sto EmeraldCoat®
Code compliant paperor felt water-resistivebarrier (WRB)
Expanded metal lath
Sto Flexyl and mesh
Sto Primer
Sto base coat andmesh lapped ontostucco
Foam shape
Sto adhesive
StoPowerwall stucco
Sto primer
Sto finish (smooth ortextured)
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional,general contractor or builder. They should be installed in accordance with those specifications and Sto's instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections,for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building compo-nents or assemblies, or for other construction activities beyond Sto's control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or build-ing may result in serious damage to Sto products, and to the structure of the building or its components. STO CORP. DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED EXCEPTFOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO'S WARRANTY PROGRAMS WHICH ARE SUB-JECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers,please refer to the Sto Corp. website, www.stocorp.com.
Attention