CONFIDENTIAL

THIS DOCUMENT IS THE PROPRIETARY PROPERTY OF FC LIGHTING, INC. ANY UNAUTHORIZED TRANSFER, USE OR REPRODUCTION IS STRICTLY PROHIBITED. © FC LIGHTING, INC.

FCSL2000 Series - INSTALLATION INSTRUCTIONS

CAUTION: BEFORE CONNECTING THE FIXTURE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.

DETAILED ILLUSTRATIONSTUD WALL INSTALLATION corporatet 800.900.1730f 630.889.8106 3609 Swenson Ave. St. Charles, IL 60174

2458893

GENERAL:1. Before starting the installation, make sure all electricity has

been turned off and electrical breaker has been locked out and tagged out.

2. To ensure the success of the installation, be sure to read these instructions and review the diagrams thoroughly before beginning.

3. All electrical connections must be in accordance with local codes, ordinances, or the National Electrical Code.

NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur.

IMPORTANT: Temporarily remove Splatter Shield and contents from Back Box housing and set aside.

1. Install Drywall Mounting Brackets onto Back Box using 6-32 screws provided. Orient Back Box as shown. Fig 1

2. Adjust brackets to align front face of backbox flush to face of finished wall surface. Then fasten brackets to studs. Fig 2

3. Orient Back Box housing as shown to attach conduit. Connect conduit to backbox using 3/4” K.O.s. Fig 3

4. Optional Hanger Bar Brackets can be used to hang the Back Box between studs or braces to complete installation. Fig 4

6. Reinstall Splatter Shield and all contents using the (2) 8-32 screws provided. Fig 5

IMPORTANT: All wiring connections must be made in accordance with local electrical codes, ordinances, and the National Electric Code.

STUD

Back Box

Adjustable Back BoxPosition In / Out

DrywallMounting Brackets

Back Box

Adjustment Slots

6-32 screwsprovided

Align to face of finished wall

Fig 1

Fig 2

Back Box Conduit Entry____

Foam Block Insert toRetain Back Box Form

Splatter Shield

Wing Nuts

Threaded Rod

SL2000 SeriesUniversal Back Box

Concrete Pour Form(by others)

(4) 3/4” Knockouts - (2) on back and (1) on each side

Fig 3

Back Box Splatter Shield____

8-32 screws provided

BACKBOX

STUD

MOUNTING BRACKETS

Figure 2 (stud wall)

MOUNTING BRACKETS

BACKBOX

ADJUSTMENT SLOTS

Figure 1 (stud wall)

Figure 3 (stud wall)

SPLATTER GUARD

SL 2000 series backbox installation in hollow (stud) wall construction (2” x 4” min.): 1. Install the (2) slotted mounting brackets provided as shown in Figure 1, using the (4) 6-32 screws provided. 2. Adjust the brackets (by loosening the screws) so that the front face of the backbox will be flush or slightly in front of the finished wall surface after installation (see Figure 2). 3. Orient fixture housing electrical connections as directed on inisde label. Failure to do so will result in faceplate not installed in the correct oreintation (critical STEP for SL2003, SL2040, and SL2041 models). 4. Secure the mounting brackets to wood or metal studs (hardware by others) so that the front face of the back box will be flush or slightly in front of the finished wall surface after installation (see Figure 2). 5. Connect conduit to backbox using 3/4” NPT fittings. Pull wires into back housing for electrical connections to be made later. 6. Install splatter guard provided as shown in Figure 3, using the (2) 8-32 screws provided securely and finish wall. 7. Before continuing, remove splatter guard and debris from backbox to allow for proper fitment.

SL 2000 SERIES STUD WALL INSTALLATION

FILE NAME: SL 2000 SERIES INSTALLATION INSTRUCTIONS.SLDDRW

Foam Block Insert toRetain Back Box Form

Splatter Shield

Wing Nuts

Threaded Rod

SL2000 SeriesUniversal Back Box

Concrete Pour Form(by others)

BACKBOX

STUD

MOUNTING BRACKETS

Figure 2 (stud wall)

MOUNTING BRACKETS

BACKBOX

ADJUSTMENT SLOTS

Figure 1 (stud wall)

Figure 3 (stud wall)

SPLATTER GUARD

SL 2000 series backbox installation in hollow (stud) wall construction (2” x 4” min.): 1. Install the (2) slotted mounting brackets provided as shown in Figure 1, using the (4) 6-32 screws provided. 2. Adjust the brackets (by loosening the screws) so that the front face of the backbox will be flush or slightly in front of the finished wall surface after installation (see Figure 2). 3. Orient fixture housing electrical connections as directed on inisde label. Failure to do so will result in faceplate not installed in the correct oreintation (critical STEP for SL2003, SL2040, and SL2041 models). 4. Secure the mounting brackets to wood or metal studs (hardware by others) so that the front face of the back box will be flush or slightly in front of the finished wall surface after installation (see Figure 2). 5. Connect conduit to backbox using 3/4” NPT fittings. Pull wires into back housing for electrical connections to be made later. 6. Install splatter guard provided as shown in Figure 3, using the (2) 8-32 screws provided securely and finish wall. 7. Before continuing, remove splatter guard and debris from backbox to allow for proper fitment.

SL 2000 SERIES STUD WALL INSTALLATION

FILE NAME: SL 2000 SERIES INSTALLATION INSTRUCTIONS.SLDDRW

Fig 5

Fig 4

Optional - Hanger Bar (HB) ______

26” Max Length(14.25” Min Length)

Horizontal Adjustment

26” Max Length

Wall Stud

Wall BracingWall Stud

Hanger Bar

Hanger Bar

(14.25” Min Length)Vertical Adjustment

Drywall Mounting Brackets included w/ Back Box Kit

CONFIDENTIAL

THIS DOCUMENT IS THE PROPRIETARY PROPERTY OF FC LIGHTING, INC. ANY UNAUTHORIZED TRANSFER, USE OR REPRODUCTION IS STRICTLY PROHIBITED. © FC LIGHTING, INC.

FCSL2000 Series - INSTALLATION INSTRUCTIONS

CAUTION: BEFORE CONNECTING THE FIXTURE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.

DETAILED ILLUSTRATION

corporatet 800.900.1730f 630.889.8106 3609 Swenson Ave. St. Charles, IL 60174

2458893

BRICK WALL INSTALLATION

GENERAL:1. Before starting the installation, make sure all electricity has

been turned off and electrical breaker has been locked out and tagged out.

2. To ensure the success of the installation, be sure to read these instructions and review the diagrams thoroughly before beginning.

3. All electrical connections must be in accordance with local codes, ordinances, or the National Electrical Code.

NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur.

IMPORTANT: Temporarily remove Splatter Shield and contents from Back Box housing and set aside.

1. Install (2) slotted Masonry Mounting Brackets onto each side of the Back Box using (4) 6-32 adjustment screws provided. Orient Back Box as shown. Fig 1

NOTE: Ensure Back Box face is flush with Brick face. Fig 2

2. Then fasten brackets to brick using appropriate hardware (by others). Adjust Back Box vertical position for optimal spacing between upper and lower bricks. Then tighten adjustment screws.

3. Connect conduit to backbox using 3/4” K.O.s. Fig 3

4. Reinstall Splatter Shield and all contents using the (2) 8-32 screws provided. Fig 4

IMPORTANT: All wiring connections must be made in accordance with local electrical codes, ordinances, and the National Electric Code.

Back Box Conduit Entry____

Foam Block Insert toRetain Back Box Form

Splatter Shield

Wing Nuts

Threaded Rod

SL2000 SeriesUniversal Back Box

Concrete Pour Form(by others)

(4) 3/4” Knockouts - (2) on back and (1) on each side

Fig 3

Masonry Mounting Brackets Included w/ Back Box Kit

Flush Mounting to Brick FaceMOUNTING BRACKETS

BACKBOX

BRICK

Figure 4 (brick wall)

SPLATTER GUARD

Figure 6 (brick wall)

FLUSHED WITH FINISHED SURFACE

Figure 5 (brick wall) BRICK

SL 2000 SERIES BRICK WALL INSTALLATION

SL 2000 series backbox installation in brick wall construction (Utility Brick shown): 1. Install the (2) slotted mounting brackets provided as shown in Figure 4, using the (4) 6-32 screws provided. 2. Adjust the brackets vertically for optimal gap spaces between upper and lower brick surfaces and back housing 3. Orient fixture housing electrical connections as directed on inisde label. Failure to do so will result in faceplate not installed in the correct oreintation (critical STEP for SL2003, SL2040, and SL2041 models). 4. Secure the mounting brackets to the top of the brick (hardware by others) so that the front face of the back box will be flush or slightly in front of the finished wall surface after installation (see Figure 5). 5. Connect conduit to backbox using 3/4” NPT fitting with teflon tape on conduit. Pull wires into back housing for electrical connections to be made later. 6. Install Internal support block and splatter guard provided as shown in Figure 6, using the (2) 8-32 screws provided securely and finish wall. 7. Before continuing, remove splatter guard and debris from backbox to allow for proper fitment.

FILE NAME: SL 2000 SERIES INSTALLATION INSTRUCTIONS.SLDDRW

Fig 2

Orient Back Box As Shown

6-32 adjusment screws provided

MOUNTING BRACKETS

BACKBOX

BRICK

Figure 4 (brick wall)

SPLATTER GUARD

Figure 6 (brick wall)

FLUSHED WITH FINISHED SURFACE

Figure 5 (brick wall) BRICK

SL 2000 SERIES BRICK WALL INSTALLATION

SL 2000 series backbox installation in brick wall construction (Utility Brick shown): 1. Install the (2) slotted mounting brackets provided as shown in Figure 4, using the (4) 6-32 screws provided. 2. Adjust the brackets vertically for optimal gap spaces between upper and lower brick surfaces and back housing 3. Orient fixture housing electrical connections as directed on inisde label. Failure to do so will result in faceplate not installed in the correct oreintation (critical STEP for SL2003, SL2040, and SL2041 models). 4. Secure the mounting brackets to the top of the brick (hardware by others) so that the front face of the back box will be flush or slightly in front of the finished wall surface after installation (see Figure 5). 5. Connect conduit to backbox using 3/4” NPT fitting with teflon tape on conduit. Pull wires into back housing for electrical connections to be made later. 6. Install Internal support block and splatter guard provided as shown in Figure 6, using the (2) 8-32 screws provided securely and finish wall. 7. Before continuing, remove splatter guard and debris from backbox to allow for proper fitment.

FILE NAME: SL 2000 SERIES INSTALLATION INSTRUCTIONS.SLDDRW

Fig 1

Align to face of finished wall

Proper OrientationPosition

ProperOrientationPosition

Back Box Splatter Shield____

Fig 4

Back Box

8-32 screws provided

Foam Block Insert toRetain Back Box Form

Splatter Shield

Wing Nuts

Threaded Rod

SL2000 SeriesUniversal Back Box

Concrete Pour Form(by others)

BACKBOX

STUD

MOUNTING BRACKETS

Figure 2 (stud wall)

MOUNTING BRACKETS

BACKBOX

ADJUSTMENT SLOTS

Figure 1 (stud wall)

Figure 3 (stud wall)

SPLATTER GUARD

SL 2000 series backbox installation in hollow (stud) wall construction (2” x 4” min.): 1. Install the (2) slotted mounting brackets provided as shown in Figure 1, using the (4) 6-32 screws provided. 2. Adjust the brackets (by loosening the screws) so that the front face of the backbox will be flush or slightly in front of the finished wall surface after installation (see Figure 2). 3. Orient fixture housing electrical connections as directed on inisde label. Failure to do so will result in faceplate not installed in the correct oreintation (critical STEP for SL2003, SL2040, and SL2041 models). 4. Secure the mounting brackets to wood or metal studs (hardware by others) so that the front face of the back box will be flush or slightly in front of the finished wall surface after installation (see Figure 2). 5. Connect conduit to backbox using 3/4” NPT fittings. Pull wires into back housing for electrical connections to be made later. 6. Install splatter guard provided as shown in Figure 3, using the (2) 8-32 screws provided securely and finish wall. 7. Before continuing, remove splatter guard and debris from backbox to allow for proper fitment.

SL 2000 SERIES STUD WALL INSTALLATION

FILE NAME: SL 2000 SERIES INSTALLATION INSTRUCTIONS.SLDDRW

CONFIDENTIAL

THIS DOCUMENT IS THE PROPRIETARY PROPERTY OF FC LIGHTING, INC. ANY UNAUTHORIZED TRANSFER, USE OR REPRODUCTION IS STRICTLY PROHIBITED. © FC LIGHTING, INC.

FCSL2000 Series - INSTALLATION INSTRUCTIONS

CAUTION: BEFORE CONNECTING THE FIXTURE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.

DETAILED ILLUSTRATION

corporatet 800.900.1730f 630.889.8106 3609 Swenson Ave. St. Charles, IL 60174

2458893

POURED CONCRETE INSTALLATION

Back Box Conduit Entry____

Foam Block Insert toRetain Back Box Form

Splatter Shield

Wing Nuts

Threaded Rod

SL2000 SeriesUniversal Back Box

Concrete Pour Form(by others)

(4) 3/4” Knockouts - (2) on back and (1) on each side

Fig 2

Back Box Splatter Shield Included w/ Back Box Kit

MOUNTING BRACKETS

BACKBOX

BRICK

Figure 4 (brick wall)

SPLATTER GUARD

Figure 6 (brick wall)

FLUSHED WITH FINISHED SURFACE

Figure 5 (brick wall) BRICK

SL 2000 SERIES BRICK WALL INSTALLATION

SL 2000 series backbox installation in brick wall construction (Utility Brick shown): 1. Install the (2) slotted mounting brackets provided as shown in Figure 4, using the (4) 6-32 screws provided. 2. Adjust the brackets vertically for optimal gap spaces between upper and lower brick surfaces and back housing 3. Orient fixture housing electrical connections as directed on inisde label. Failure to do so will result in faceplate not installed in the correct oreintation (critical STEP for SL2003, SL2040, and SL2041 models). 4. Secure the mounting brackets to the top of the brick (hardware by others) so that the front face of the back box will be flush or slightly in front of the finished wall surface after installation (see Figure 5). 5. Connect conduit to backbox using 3/4” NPT fitting with teflon tape on conduit. Pull wires into back housing for electrical connections to be made later. 6. Install Internal support block and splatter guard provided as shown in Figure 6, using the (2) 8-32 screws provided securely and finish wall. 7. Before continuing, remove splatter guard and debris from backbox to allow for proper fitment.

FILE NAME: SL 2000 SERIES INSTALLATION INSTRUCTIONS.SLDDRW

Orient Back Box As Shown

ProperOrientationPosition

Back Box Face Flush to Concrete_ Back Box Face Flush to Composite

Fig 4Fig 3

GENERAL:1. Before starting the installation, make sure all electricity has

been turned off and electrical breaker has been locked out and tagged out.

2. To ensure the success of the installation, be sure to read these instructions and review the diagrams thoroughly before beginning.

3. All electrical connections must be in accordance with local codes, ordinances, or the National Electrical Code.

NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur.

IMPORTANT: Temporarily remove Splatter Shield and contents from Back Box housing and set aside.

1. Install the (2) Threaded Rods provided in through the Splatter Shield and into the Back Box as shown. Fig 1

2. Ensure that face of Back Box is flush with face of finished surface. Connect conduit to backbox using 3/4” K.O.s. Fig 2 Orient Back Box in proper position as shown.

NOTE: Ensure front of Back Box is flush with finished wall face.

2. Reinstall the Splatter Shield and contents into the Back Box and allow Threaded Rods to pass through the Pour Form. Fasten the Back Box assembly to the Pour Form using (2) Wing Nuts provided on the already installed Threaded Rods. Refer to Fig 3.

4. For additional Composite or Topcoat finish, again ensure front of Back Box is flush with finished wall face. Fig 4

IMPORTANT: All wiring connections must be made in accordance with local electrical codes, ordinances, and the National Electric Code.

Figure 7 (concrete pour)

INTERNAL SUPPORT BLOCK

SPLATTER GUARD

WING NUTS

THREADED ROD

Figure 8 (concrete pour)

POUR FORM

SL 2000 SERIES POURED CONCRETE INSTALLATION

SL 2000 series backbox installation in poured concrete construction: 1. Install the (2) threaded rod provided as shown in Figure 7, using the (2) 8-32 x 2" long rods provided. 2. Attach assembly to pour form ensuring the Orientation of the backbox housing electrical connections is followed per inside label instructions. Failure to do so will result in faceplate not installed in the correct oreintation (critical STEP for SL2003, SL2040, and SL2041 models).

FILE NAME: SL 2000 SERIES INSTALLATION INSTRUCTIONS.SLDDRW

Proper OrientationPosition

Fig 1

Figure 7 (concrete pour)

INTERNAL SUPPORT BLOCK

SPLATTER GUARD

WING NUTS

THREADED ROD

Figure 8 (concrete pour)

POUR FORM

SL 2000 SERIES POURED CONCRETE INSTALLATION

SL 2000 series backbox installation in poured concrete construction: 1. Install the (2) threaded rod provided as shown in Figure 7, using the (2) 8-32 x 2" long rods provided. 2. Attach assembly to pour form ensuring the Orientation of the backbox housing electrical connections is followed per inside label instructions. Failure to do so will result in faceplate not installed in the correct oreintation (critical STEP for SL2003, SL2040, and SL2041 models).

FILE NAME: SL 2000 SERIES INSTALLATION INSTRUCTIONS.SLDDRW

Finished WallSurface

Align housing to face of finished wall

Align housing to face of finished wall

Finished Wall Surface

Concrete, Blockor Brick Structure

Stucco or othersurface topcoat

18 AWG Anti-wicking CableWaterproof Wire Nuts (3) Included

IP68 Rated SealedOptical/Driver Unit

Hanger Bar Thru KOHorizontal & Vertical

6-32 ThreadedInserts forMounting Brackets

(4) Ø 3/4” KO(Ø 1-1/8 True Size)(2 in back & 1 @ each end)

TRSTamper ResistantScrew (Optional)

CONFIDENTIAL

THIS DOCUMENT IS THE PROPRIETARY PROPERTY OF FC LIGHTING, INC. ANY UNAUTHORIZED TRANSFER, USE OR REPRODUCTION IS STRICTLY PROHIBITED. © FC LIGHTING, INC.

FCSL2000 Series - INSTALLATION INSTRUCTIONS

CAUTION: BEFORE CONNECTING THE FIXTURE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.

DETAILED ILLUSTRATION

corporatet 800.900.1730f 630.889.8106 3609 Swenson Ave. St. Charles, IL 60174

2458893

GENERAL:1. Before starting the installation, make sure all electricity has

been turned off and electrical breaker has been locked out and tagged out.

2. To ensure the success of the installation, be sure to read these instructions and review the diagrams thoroughly before beginning.

3. All electrical connections must be in accordance with local codes, ordinances, or the National Electrical Code.

NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur.

1. To finish step light installation, remove the Splatter Shield and all contents from the Back Box. Complete all wiring in the Back Box, then snap the fixture assembly into the back box using the Snap-In Captures & Leads. Fig 1

2. Use Shims to compensate for misalignment of the front of the Back Box and the finished wall surface. Fig 2

3. Ensure proper orientation of Back Box as shown. Connect conduit to backbox using 3/4” K.O.s. Fig 3

4. Splatter Shield and standard mounting installation hardware are included in and ship with the Back Box assembly. (2) 8-32 screws provided to secure and remove the Splatter Shield and contents. Fig 3

7. Optional Tamper Resistant Screws (TRS) can be usd for additional security using Torx Pin screws, painted to complement the faceplate. Fig 4

3) WIRING: Make wiring connections. All wiring connections must be made in accordance with local electrical codes, ordinances, and the National Electric Code.

Fixture Snaps into Back Box

FixtureAssembly

Snap-In Capture

Right Side

Left Side Universal Back BoxTop

Fixture WiringOut

Snap-In Lead

Fig 1

Back Box Splatter Shield____

Distance recessed = X

Snap-In Lead

Snap-In Capture

Wall surface

Wall surface

Added Shims to equal “X” X

Torx screws w/ pin, finished to complement faceplate finish.

Optional - Tamper Resistant Screws (TRS)

Tamper Resistant Torx Screws(TR20 w/Pin)

Shims provided to compensate for Back Box misalignment.

Shims - (8 ea.) included w/ Fixture

Fig 2

FIXTURE & BACK BOX ASSEMBLY

Foam Block Insert toRetain Back Box Form

Splatter Shield

Wing Nuts

Threaded Rod

SL2000 SeriesUniversal Back Box

Concrete Pour Form(by others)

(4) 3/4” Knockouts

(2) on back,(1) on each side

Fig 3

BACKBOX

STUD

MOUNTING BRACKETS

Figure 2 (stud wall)

MOUNTING BRACKETS

BACKBOX

ADJUSTMENT SLOTS

Figure 1 (stud wall)

Figure 3 (stud wall)

SPLATTER GUARD

SL 2000 series backbox installation in hollow (stud) wall construction (2” x 4” min.): 1. Install the (2) slotted mounting brackets provided as shown in Figure 1, using the (4) 6-32 screws provided. 2. Adjust the brackets (by loosening the screws) so that the front face of the backbox will be flush or slightly in front of the finished wall surface after installation (see Figure 2). 3. Orient fixture housing electrical connections as directed on inisde label. Failure to do so will result in faceplate not installed in the correct oreintation (critical STEP for SL2003, SL2040, and SL2041 models). 4. Secure the mounting brackets to wood or metal studs (hardware by others) so that the front face of the back box will be flush or slightly in front of the finished wall surface after installation (see Figure 2). 5. Connect conduit to backbox using 3/4” NPT fittings. Pull wires into back housing for electrical connections to be made later. 6. Install splatter guard provided as shown in Figure 3, using the (2) 8-32 screws provided securely and finish wall. 7. Before continuing, remove splatter guard and debris from backbox to allow for proper fitment.

SL 2000 SERIES STUD WALL INSTALLATION

FILE NAME: SL 2000 SERIES INSTALLATION INSTRUCTIONS.SLDDRW

8-32 screws provided

Proper OrientationPosition

Fig 4