student presentation isss award

25
2014 ISSS Student Award Presentations PAPERCRETE-Towards a new beginning • Name of the authors: Jil Sheth Saransh Joshi • Faculty of Technology, CEPT University • Name of the adviser: Mrs. Anal Sheth Category: UG

Upload: jil-sheth

Post on 20-Jun-2015

827 views

Category:

Engineering


4 download

DESCRIPTION

we were nominated for our research at isss awards.this is presentation of the same.

TRANSCRIPT

Page 1: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

sPAPERCRETE-Towards a new beginning

• Name of the authors: Jil Sheth

Saransh Joshi• Faculty of Technology, CEPT

University

• Name of the adviser: Mrs. Anal Sheth

Category: UG

Page 2: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Motivation

• With the ever increasing pace of industrialization, the carbon footprint has increased considerably at an alarming rate. Cement manufacturing itself contributes to about 5% of the total emission of greenhouse gases. As a result, it has became imperatively necessary to evolve such practices and techniques that considerably reduce the carbon footprint and are environmental friendly in nature. A huge amount of resources and a lot of carbon footprint is consumed in the manufacture of materials used in construction industries especially cement. Cement manufacturing consumes large quantum of energy and requires the extensive use of various resources.

Page 3: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Motivation

• But, it is an integral ingredient in the manufacturing of Concrete, which is the most commonly used building material all over the world. So, a systematic effort to replace or at least reduce the amount of cement in concrete can have a huge impact on Carbon footprint reduction and can drastically change the entire scenario. This was precisely the central idea behind this research.

• Also need to develop of low cost housing for less fortunate people was motivation.

• Need for sustainable eco-friendly building material.

Page 4: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

sProblem statement

The real problem laid in the fact that there are no specific guidelines and standards for manufacturing ‘Papercrete’

Specific objectives:

Understanding the material, its properties and its workability by casting various forms and building various small elements.

To observe, record ,analyze and compare the properties of papercrete based on empirical evidences obtained by testing the material.

To gain an insight about its overall feasibility and its appearance.

To gain an idea about the approximate quantity of various ingredients needed for producing a certain standard amount of papercrete.

Page 5: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Methodology

Papercrete moulds were prepared before hand and ideally wood is suited for this.The main materials used for papercrete mix preparation were waste paper (newspaper), Portland cement OPC-53 grade, Sand, Potable water and Soil.Four types of mixes were prepared for the experiment. Mix proportions by volume in percentages are indicated below:1) 50% wet paper pulp/ 30% damp earth/ 10% dry sand/ 10% Portland cement2) 60% wet paper pulp/ 20% damp earth/ 15% dry sand/ 15% Portland cement3) 65% wet paper pulp/ 25% damp earth/ 10% Portland cement4) 70% wet paper pulp/ 15% damp earth/ 15% Portland cement 

Page 6: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Methodology (continued)

There is a lack of any statistical data recorded regarding the physical characteristics of papercrete in regions like Ahmedabad which have relatively hotter climate.

So, we conducted our tests during the month of June, when the temperature was round about 42-47 degree centigrade.

Various elements of different sizes were cast, predominantly a wall and an arch (compression member).

The units were bound together with mortar in case of a wall, and using lock and fit mechanism in case of arch (without mortar).

Three types of mortar mixes were prepared for binding the papercrete blocks in the wall

1)Cement , Sand and Water (C-S -1:4)

2)Cement, Sand, Water and Paper Pulp (C-S-P -1:4:6)

Page 7: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Methodology (continued)

c)And,lastly,Cement, paper pulp and water (C:P:W-2:4:1).

The last one was found to be most appropriate and it was used for providing proper strength and bonding in the papercrete masonry.

The major steps for preparation of blocks and related equipment used are described below:

• IS sieve 4.75mm was used to remove all coarse aggregate from the sand and soil by temping.

• Shredded newspaper was wetted in water in the curing tank and a motor run machine called the pulp beater machine was used to obtain wet paper pulp.

• Next, the soil, sand, pulp and cement were mixed into a more uniform and consistent mass with help of a cement mixer. The mixer machine was allowed to work for around 3 to 4 minutes to obtain papercrete.

 

Page 8: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Methodology (continued)

• Wooden moulds were prepared in the experiment but acrylic or plastic sheets can also be used for mould. The moulds were then greased with burnt oil or taping was done on the moulds which may help in releasing the blocks quickly and easily.

• The papercrete mix was then poured into moulds and compacted on a vibrating to remove voids and achieve more density, resulting in stronger and more durable product. Temping bar was also used for the same purpose.

• The mix was then leveled to achieve satisfactory dimensions and finish.

• After 40 hours, papercrete seemed to attain sufficient amount of strength after which the moulds were released and casted blocks were allowed to sundry for further strength gain and development of load carrying capacity.

Page 9: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Water absorption tests

Page 10: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Compressive strength test

Page 11: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Results

• The above lab scale manufactured papercrete blocks were tested for key properties and following values were obtained.

• Compressive Strength• Compressive strength tests on 15 cm x 15 cm x 15 cm papercrete

cubes revealed an average compressive strength of 0.57 N/mm2

after 3 days of cube preparation. Other research also suggests similar results. [1, 5]. For more strength, higher grade of cement can be used.

• Weight and Density• Density of the material increased with increase in the percentage

of cement in the mixture and reduced with increase in the amount of the paper in the mixture. Average weight of 8 cubes casted was observed to be 3.624 kg, thus block density was about 1.07 gm /cc. This is therefore lightweight in comparison to standard concrete or brick masonry units.

• Shrinkage• Shrinkage measured was between 8-9% in each block.

Page 12: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Results (continued)

• Water absorption

• Water absorption of the blocks was about 30% in all cases.

• Drying time

• 40 hours at least are needed for drying of papercrete before it can be demoulded. After this it should be sundried for 4 days before usage for better strength. Or it can be placed in oven at nearly 70 °C for 40 hours after casting. Putting it at higher temperature than this can result into segregation of material.

Page 13: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Pulp beater

Beater machine is a motor run machine which can be made by attaching blade to axle of a vehicle or old car. It helps in making consistent pup out of pieces of wet newspaper.

Page 14: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Other equipment needed

• Cement mixer• Trowel• Temping rods• IS sieves -4.75 mm• Scooper• Leveler• Pan• Vibrating machine

Page 15: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Designing of module

Page 16: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Mold making

Page 17: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Soaking of paper

Page 18: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Making of paper pulp

Page 19: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Temping of soil

Page 20: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Volumetric batching

Page 21: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Compaction

Page 22: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Sundry

Page 23: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Assembly

Page 24: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Main points

• Lack of official guidelines and standard procedure describing the method of producing papercrete.

• Solution: By initially casting elements and smaller blocks and elements by varying proportions of constituent elements and checking their strength by experimentation before casting the final elements.

• Papercrete is far lighter a material than concrete or wood has good water absorption and insulation capacity, less shrinkage and is environment friendly, has high strength to weight ratio.

Although this area requires significant amount of research, but papercrete can ideally be used for reduction in dead weight of structural elements in cases where there are no special loads acting on the element. Also, about 55% of paper waste around the globe still doesn’t get recycled and is directly disposed and a considerable portion of it can be used for manufacturing papercrete. Future research on improving it’s tensile strength can widen up the possibilities of papercrete using it as a construction worldwide.

Page 25: Student presentation ISSS award

20

14

IS

SS

Stu

den

t A

ward

Pre

sen

tati

on

s

Acknowledgments

• We are thankful to our faculties, Mr. Nikunj Vakani and Mr. Pranav Gajjar for guiding us through the papercrete workshop. We also thank the lab assistants at the University for their support. We acknowledge the efforts of our team members in this workshop. We are grateful to Prof. Anal Sheth for her valuable inputs and motivation throughout this work.

Thank you. Any questions?