studio monitor placement: positioning tips for optimal sound

8/17/2019 Studio Monitor Placement: Positioning Tips for Optimal Sound

1/14

26/07/15 22:10Studio Monitor Placement: Positioning Tips for Optimal Sound

Page 1 of 14http://ehomerecordingstudio.com/studio-monitor-positioning/

Studio Monitor Placement: Positioning Tips for Optimal

Sound

It sounds silly to spend thousands on studio

monitors…

Only to waste their potential by not taking

the time to position them right.

Doesn’t it?

Yet many folks do exactly that. Because what

they don’t realize is…

A seemingly small detail like monitor

placement can have an even greater impact

on your sound…

Than the monitors themselves!

Poorly-positioned…they can create

HUGE peaks and valleys in the frequency

response of your room…

Destroying any chance you had of crafting a well-balanced mix.

To help you avoid that misfortune, for today’s post I’ve created this in-depth guide on

studio monitor placement.

First up…

The Standard Mixing Position

While the “correct mixing position” is always subject to debate…

The majority of today’s engineers are in agreement as to what is generally

http://ehomerecordingstudio.com/best-studio-monitors/http://ehomerecordingstudio.com/best-studio-monitors/http://ehomerecordingstudio.com/best-studio-monitors/


2/14



considered “ideal.”

And that “ideal position” can besummed up with 2 simple rules:

1. Your head should form an equilateral triangle your monitors

The following diagram shows how it should look:


3/14



The logic here is: Without a standard in place, stereo image widths may vary

drastically from one studio to another.

To solve this problem…


4/14



The equilateral triangle method was likely devised as an easy-to-remember rule

that offers a good compromise between too-wide and too-narrow.

The next rule is…

2. Point the monitors directly toward your head

The following diagram shows the proper setup:

The logic here is: Because high frequencies are more “directional ” than low

frequencies….

They sound noticeably stronger when the tweeters are pointed directly at you…compared to when they’re NOT.


5/14



Just like with Rule #1…

Rule #2 was likely developed as a way to maintain a consistent listening perspective

from one studio to another.

So that covers the basics of monitor placement. Now let’s move on to the more-

advanced stuff .

Starting with…

Room Modes Explained

While the goal of monitor placement is to create an environment where:

A natural balance of sounds can exist, un-colored by room acoustics…

The BIGGEST obstacle to achieving that goal is a condition known as room modes…


6/14



Which form whenever a room’s dimensions are EITHER:

the same length as the sound wave, or…

a multiple of the half-wavelength (1.5, 2, 2.5, etc.).

At those frequencies, the sound waves get trapped between opposing walls, creating

what’s known as a standing wave…

Which affects both the volume, and rate-of-decay of that frequency…and distorts the

overall acoustics of the room.

When 2 room dimensions are equal, like in a standard 10!10 bedroom, the

problem is amplified because you have twice as many standing waves at the samegroup of frequencies.

That is also the reason you hear people say that cubed-rooms are the worst .

Up next…

Frequency vs. Wavelength


7/14



In a typical-sized home studio, you only see problems with standing waves below

frequencies of 300 Hz.

And here’s why:

At higher frequencies, sound waves are shorter…

While at lower frequencies, they’re longer.

For example:

20,000 Hz = 0.05 ft

10,000 Hz = 0.1 ft

1,000 Hz = 1.1 ft

500 Hz = 2.3 ft

200 Hz = 5.7 ft

100 Hz = 11.3 ft

20 Hz = 56.5 ft


8/14



As lower frequencies approach the size of a room’s dimensions…they become

increasingly affected by the room itself.

That’s one reason why larger rooms are better, since they only have problems with

standing waves at the lowest bass frequencies.

In smaller rooms, the problems are usually much greater.

The good new is: there are solutions. So let’s learn them now…

Solution #1: Better Positioning

To tame the effects of standing waves in your room, the standard strategy is:

to create singular waves at multiple frequencies

as opposed to multiple waves at fewer frequencies.

This is done by varying the distances between your monitors and each wall.

That way, the impact of each wave at each frequency is minimized, and the frequency

response of the room remains as flat as possible.

To employ this strategy, all you need to do is follow these steps when setting up your

monitors:

1. Position monitors against the longest wall.

When it comes to the width of your room, you really can’t vary the distances from the

side-walls, because you still need to maintain a symmetrical stereo image.

In this case, the next best solution is to set up your monitors against the longest wall

to minimize problems from side reflections.

Up next…

2. Vary those distances.


9/14



At this point, pull out a measuring tape and a notepad, because it’s time to compare

some distances.

First off , ensure that the height of your monitors is either slightly above, or slightly

below the mid-way point between the floor and ceiling.

Next , measure the distance between the monitors and the side-walls, to ensure that

they’re neither the same (nor an exact multiple of ) the previous two distances.

If they are, simply make adjustments and re-measure until everything looks good.

Up next…

3. Create space between the monitors and the rear wall.

Because bass frequencies project outward in all directions…much of that sound

travels backwards and reflects off the rear wall of your room.

The problem is, when it recombines with the direct sound from the monitors…

The “in-phase“ frequencies get amplified, and the “out-of-phase“ frequencies cancelout. This principle is known as the boundary effect.

To solve the problem, pro studios often build their monitors directly into the wall,

thus eliminating all rear reflections. (Here’s an example).

However, since this solution is far too expensive home studios…

The next best option is to create the maximum separation between the wall andthe monitors that the room-size will allow. For most rooms, that’s between 1-2 feet.

This won’t SOLVE the problem, but it will lessen it somewhat, by reducing the

strength of the reflections.

Another useful trick is to use monitors with FRONT bass ports, such as the Adam

Audio A7X, because unlike rear-facing bass ports, they direct a larger portion of theenergy forward , AWAY from the walls.

http://ehomerecordingstudio.com/amazon/adam-a7xhttp://www.pinterest.com/pin/309692911851691257/


10/14



In really small rooms, these monitors save space by allowing you to position them

closer to the wall.

Up next…

4. Find a good head position

In the same way that monitor positioning has a big impact on your sound…so too

does head positioning.

And so, following the same basic principles…here’s how to find the ideal position for

YOURSELF:

1. Center your chair between the side walls to maintain symmetrical

stereo image.

2. Set the chair height so your head is NOT halfway between the ceiling

and floor.

3. Set the chair/desk position so that it is NOT halfway between the

front and back walls.

4. Measure and compare the distances on all 3 dimensions to ensurethey’re neither the same, nor exact multiples of each other.

Once that’s done, you’re ready for the next step…

Solution #2: Acoustic Treatment

Now that you’ve positioned both your monitors and chair…

Next it’s time to design an acoustic treatment plan around those two positions.

Here’s how it’s done:

1. Add bass traps behind monitors

Earlier I mentioned how reflected bass frequencies from your rear wall can cause

problems.


11/14



Well the absolute BEST way to minimize those problems is to add bass traps directly

behind each monitor.

If you only follow one tip from this article…FOLLOW THIS ONE. Because it makes

a huge difference.

If you don’t have spare bass traps, acoustic panels or ANY other type of absorption

works FAR better than nothing.

Up next…

2. Add absorption at initial reflection points

If you’re familiar with initial reflection points, then you know there are 4 KEY

locations that cause the majority of problems with reflected sound from your

monitors:

Two are above your head

One is on the left wall

One is on the right wall

If you AREN’T familiar with them yet, here’s how to find them:

Imagine that the walls and ceiling of your room are mirrors. From your seated

mixing position, the initial reflection points are the spots on the wall where you

would see the reflections of your monitors.

Simply cover up those 4 spots with acoustic panels, and you’re all set.

Up next…

3. Add diffusion to the rear wall

Even though the sound waves from your monitors spread out in ALL directions…

The MAJORITY of that energy is focused directly at you…and the wall behind yourhead .


12/14



If that wall is flat , it’s a liability…because it has the potential to create more standing

waves than any surface in the room.

However…

If that wall is covered in diffusers, it becomes an asset , because it scatters all that

energy before it ever has the chance to cause problems.

Combine this tip with the 2 previous ones, and you’ve got a great recipe for success.

Up next…

Suggested Tools

Now that you’ve got a plan, here are a few links to some tools that might help you:

First, if you need acoustic treatment, check out this article:

The next item I recommend is a pair of isolation pads for your monitors. In

addition to acoustically isolating your them from the desk…

They also offer a way to easily adjust tilt . For monitor placement, this has 2

advantages:

1. Tilting the monitors up or down creates less potential for standing

waves between the front and rear walls.

2. Tilting allows you to readjust the angle towards your head as your

raise or lower the height.

These are the top models I recommend:

http://ehomerecordingstudio.com/acoustic-treatment-101/


13/14



Next , for those with a decent-sized room, I recommend adding a pair of monitor

stands.

Compared to desk-shelves, these stands offer maximum flexibility with positioning,

making your job a lot easier.

These are the ones I recommend:

And finally, to conclude this article:

Testing the Results of Your Work

Once you’ve completed all the steps, everything should sound good, in-theory. But

just to verify it sounds good in-reality…

Some people use a test known as a bass sweep to pin-point possible problems in the

low-end frequency response of a room.

Here’s an example. Check it out:

http://ehomerecordingstudio.com/studio-monitor-stands/http://ehomerecordingstudio.com/monitor-isolation-pad/


14/14



What you hear in this recording is a series of descending bass tones, played at a

constant level.

To test your room, play this recording (or any equivalent) through your monitorsand listen for significant changes in volume from one note to the next.

If they sound consistent, then all is well.

If NOT, chances are there’s a problem with your current setup. And unfortunately,

the only way to fix it is to start over from the beginning, try again, and retest.

While it may take a few attempts to get it right, trust me when I say…

All your efforts will be well-worth-it once you hear the end-result.

If you found this post useful, and want to learn more…

Sign up for our free video training course, or…

Follow us on Social Media by clicking below…!!
https://ehomerecordingstudio.leadpages.net/leadbox/1431f1e73f72a2%3A162f52aec346dc/5724160613416960/

studio monitor placement: positioning tips for optimal sound

Documents