sub-zero design guide - aj madison...sub-zero design guide 3 important note as you follow these...

SUB-ZERO DESIGN GUIDE

SUB-ZERO® is a registered trademark of Sub-Zero, Inc.

C O N T E N T S

Built-In Refrigeration 4

Integrated Refrigeration 31

Wine Storage 50

Undercounter Refrigeration 67

Warranty 77

Features and specifications indicatedherein and on our website are subjectto change at any time without notice.Check our website, subzero.com, forthe most up-to-date specifications.

S U B - Z E R O D E S I G N G U I D E

3

I M P O R T A N T N O T E

As you follow these instructions, youwill notice warning and caution symbols.This blocked information is importantfor the safe and efficient installation ofSub-Zero equipment. There are twotypes of potential hazards that mayoccur during installation.

Another footnote we would like toidentify is IMPORTANT NOTE: Thishighlights information that is especiallyrelevant to a problem-free installation.

signals a situation where minorinjury or product damage may occurif you do not follow instructions.

states a hazard that may causeserious injury or death if precautionsare not followed.

C O N T A C TI N F O R M A T I O N

Sub-Zero CustomerService:800-222-7820

Website:subzero.com

W E L C O M E T O S U B - Z E R O

We make the ultimate built-in, integrated andundercounter refrigerators, freezers and winestorage units. We offer more solutions to yourdaily design problems of trying to work thelargest appliance into a home without beingobtrusive. Placing refrigeration in the home is nolonger a problem, but, rather, an opportunity toexercise your creativity.

Sub-Zero has rethought traditional built-inrefrigeration, a category it pioneered, with over60 years of experience. When our complete lineof configurations—all refrigerator and all freezer,over-and-under, or side-by-side—are coupledwith three design alternatives and classic,platinum and carbon stainless steel finishes, theresult is unlimited flexibility in satisfying yourclient‘s needs for residential refrigeration.

Created to blend invisibly into your home‘sdecor, the Integrated line lets you incorporaterefrigeration anywhere in the house—the kitchen,master suite, media room or workout room.These tall units or two-drawer base refrigerators,freezers and combination units can be hiddeninside the furniture or cabinetry of yourchoosing.

Sub-Zero is breaking with conventional ways ofoffering Wine Storage for designers and theirclients. Our Built-In and Integrated models, alongwith the free-standing Model 424FS, offer unlim-ited design and storage capabilities.

Our reputation is legendary. We have engineeredand manufactured the best products in thebusiness, and we stand behind our productswith an unsurpassed warranty and a network oftechnicians to help you if service is necessary.See details of our warranty at the end of thisguide.

Comprehensive installation instructions areshipped with each model. Refer to thoseinstructions in preparing and installing allSub-Zero products. These instructions alongwith product specifications and downloadable2D and 3D CAD files, as well as pdf files can befound on our website, subzero.com.

Dimensions inparentheses are inmillimeters unlessotherwise specified.

B U I LT - I N R E F R I G E R A T I O N

4


Sub-Zero’s Built-In line offers you the mostcomplete set of design options in built-in refrig-eration for all of its models, from the classic lookof the framed unit to the beauty of the overlaymodels and the professional treatment of thewrapped stainless steel doors.

Aside from the classic stainless steel, Sub-Zerooffers platinum and carbon premium stainlesssteel finishes on its Built-In models and manyrelated accessories. The only exception to thesedesign alternatives are Models 648PRO and648PROG, which are offered only in the classicstainless steel design application. In addition,Models 685 and 695 are offered in framed,overlay and classic stainless steel (not platinumor carbon).

Glass doors are available on our Models 601R,611 and 650. They each come in a framed,overlay and stainless steel design. They all meetstringent Department of Energy standards.Model 648PROG also features a glass door in itsclassic stainless steel look.

In the illustrations, we have shown the threedifferent design configurations of the framed,overlay and stainless steel units applied toModel 695. Please note how we qualify thedifferent looks with the model number.

The traditional framed units come with anelegant full-length handle and an 11" (279)louvered grille.

Model 695/SClassicStainless Steel

Model 695/OOverlay

Model 695/FFramed

Overlay models will come with no handlehardware, because the beauty of this design isthat you can match the surrounding cabinetryhardware; however, we do offer optional handlesas sales accessories. The new ice and waterdispensing Models 685 and 695 are able toaccept overlay panels. Overlay models will comewith a standard 11" (279) panel grille that willaccept decorative panel inserts. Models 601R,601RG and 601F are only available with thelouvered grille. No panel grille option is available.

All stainless steel models, with the exception ofthose mentioned earlier, are offered in the classicstainless steel finish and in the premium finishesof platinum and carbon. Stainless steel modelscome with a standard 11" (279) heavy-dutygrille, 1" (25) diameter stainless steel handlesand a stainless steel kickplate.

All grilles will be offered as options in 1" (25)increments from 10" (254) to 15" (381) and canbe ordered as sales accessories. Models 601R,601RG, 601F, 648PRO and 648PROG are theexception and are available only with an 11"(279) grille.

An important step in assuring a successful planis to make sure that the actual equipmentshipped to your installation site matches thedesign you have ordered. Each of these threedesign options—framed, overlay and stainlesssteel—has specific installation requirements,which means it is vital that the unit match yourplanning and space needs.


5

36"(914)

73"(1854)

36"(914)

42"(1067)

42"(1067)

48"(1219)

48"(1219)

48"(1219)

48" (1219)

84"(2134)

84"(2134)

84"(2134)

84"(2134)

84"(2134)

84" (2134)

84" (2134)

30"(762)

84"(2134)

A L L R E F R I G E R A T O R | A L L F R E E Z E R

O V E R - A N D - U N D E R

S I D E - B Y - S I D E

M O D E L 6 0 1 R *

All Refrigerator

Energy StarQualified

M O D E L 6 0 1 R G *

All Refrigeratorwith Glass Door


M O D E L 6 0 1 F *

All Freezer

With the installation of a harness kit,these appliances are Star-K compliantto meet strict religious regulations inconjunction with specific instructionsfound on www.star-k.org. Models648PRO and 648PROG are Star-Kcertified from the factory with no extrawiring harness required. For detailsabout the harness kit, contact yourSub-Zero dealer.

36"(914)

73"(1854)

36"(914)

73"(1854)

M O D E L 6 6 1 * M O D E L 6 4 2 * M O D E L 6 8 5 *

Ice | WaterDispensing

M O D E L 6 3 2 * M O D E L 6 9 5 *

Ice | WaterDispensing

M O D E L 6 4 8 P R O

Free-Standingor Built-In

M O D E L 6 4 8 P R O G

Free-Standingor Built-In

M O D E L 6 1 1 *


M O D E L 6 1 1 G *

with Glass Door

M O D E L 6 5 0 *


30" (762)

84"(2134)

36"(914)

84"(2134)

36"(914)

84"(2134)

M O D E L 6 5 0 G *

with Glass Door


These illustrations represent the full line ofSub-Zero Built-In models shown in the stain-less steel design application with heavy-dutygrille. Models 648PRO and 648PROG areavailable as built-in or free-standing units inclassic stainless steel only.

For information regarding specific Built-Inmodels, refer to the illustrations in thissection. Regardless of the specific designapplication, framed, overlay or stainless steel,the interior specifications of each model areidentical.

Comprehensive installation instructions areshipped with each model. Refer to thoseinstructions in preparing and installing allSub-Zero products. The instructions can alsobe found on our website, subzero.com.

*Verify availability with your local dealer or distributor.



6

S U B - Z E R OW A R R A N T Y

Sub-Zero productsare covered by atwo, five and twelveyear residentialwarranty (exclusionsapply). See warrantydetails at the end ofthis guide.

B U I LT - I N F E A T U R E S

Framed models—the classic look that madeSub-Zero famous—feature a louvered grille andelegant full-length handle. An optional panel grilleis available for framed units, except for Models601R, 601RG and 601F. Optional panel conver-sion kits are available for the new ice and waterdispensing Models 685 and 695.

Overlay models blend seamlessly into youroverall room design and complement surroundingcabinetry. You add decorative hardware. Overlaymodels come with a panel grille that will acceptdecorative panel inserts. The new ice and waterdispensing Models 685 and 695 are also avail-able in the overlay application.

Stainless steel models feature wrapped doors,1" (25) diameter stainless steel handles and aheavy-duty grille designed specifically to enhancethe aesthetics of today's professional lookingkitchens. All Built-In stainless steel models areoffered in the classic stainless steel finish and inthe premium finishes of platinum and carbon,except for Models 685, 695, 648PRO and648PROG, which are offered in classic stainlesssteel only. The premium finishes are treated asspecial orders and must be ordered 90 daysbefore you expect delivery.

Dual Refrigeration System. All Built-In combina-tion models have the Sub-Zero dual refrigerationsystem, which ensures the freshest food andenergy efficiency at the same time. You haveprecise independent control of the refrigeratorand freezer compartments. In addition to twocompressors, the PRO 48 has three separateevaporators to keep foods fresher longer andprevent odor transfer.

Glass Door. Model 601RG is an all refrigeratorunit featuring a glass door. Models 611G and650G are over-and-under combination units witha glass door on the refrigerator. These glass doormodels come in framed, overlay and stainlesssteel designs and meet stringent Department ofEnergy standards. The side-by-side Model648PROG features a glass door on the refrigera-tor side and comes in classic stainless steel only.

Stainless Steel. The PRO 48 (Models 648PROand 648PROG) feature stainless steel construc-tion inside and out with classic finish forprofessional strength and beauty.

Ice and Water Dispensing. Models 685 and 695feature a dispenser that gives you both ice andchilled water through the refrigerator door.

Built-In Design. True cabinet depth design meansevery inch of the interior is easy to reach. ThePRO 48 can be built in or, with the free-standingaccessory kit, used in a free-standing application.

Fresh Food. High-humidity crisper drawer withremovable dividers is large and deep, withsmooth sides for easy cleaning. The top refriger-ated drawer on the PRO 48 features a tight-seal,retracting glass crisper lid that keeps produceexceptionally humid and fresh.

Electronic Controls. Up-front touch controlsgive you digital readings for quick, easy-to-readreference. The microprocessor provides supremecontrol, accurate to within one degree of presettemperatures, automatic defrosting that senses,then adapts to your use patterns, and a serviceindicator light. The PRO 48 also features exteriortemperature displays.

Advanced Lighting. Bright lighting spreadseven illumination throughout the compartment.The source of the illumination is concealed. ThePRO 48 top LED lights bathe upper compart-ments in a soft glow. On the refrigerator side,channeled sidewall LEDs can even serve as adoor-area night-light for Model 648PROG.

Adjustable Shelves. Cantilevered glass shelvesmake repositioning quick and easy. They are easyto clean, spill proof and steel reinforced for dura-bility. The PRO 48 features glass shelves withstainless steel trim in the refrigerator and 100%stainless steel shelves in the freezer.

Slide-Out Bins. An exclusive PRO 48 feature—these versatile stainless steel bins hold smallitems, remove easily, and fit neatly under anyshelf.

Door Shelves. All door shelves are adjustable forcomplete flexibility and convenience.

Dairy Storage. Dairy compartment is adjustable,with easy, one-door access, compartmentdividers and a clean design. The dairy shelf ismagnetically sealed to maintain freshness.

Automatic Ice. Ice maker provides high-quality,crescent-shaped ice that won‘t stick to the sideof the glass. The PRO 48 features a water filterlocated just behind the easy-access pop-up grille,for ice as pure as it is fresh.

Energy Efficient. Our solid core doors improveinsulation and structural integrity and help usexceed tough Department of Energy standards.Magnetic gaskets around all doors give extra-tight seals.

Kickplate. Solid, adjustable kickplate gives a truebuilt-in look and conforms to American Instituteof Architects standards.

7


M O D E L 6 0 1 F

A L L F R E E Z E R

M O D E L O P T I O N S

Framed Design 601F/F

Overlay Design 601F/O

Classic Stainless Steel 601F/S

Platinum Stainless Steel 601F/P

Carbon Stainless Steel 601F/B

S P E C I F I C A T I O N S

Overall Width 36" (914)

Overall Height 73" (1854)

Overall Depth 24" (610)

Freezer Capacity 19.3 cu ft (547 L)

Min Height Required 723/4" (1848)

Door Swing Clearance 361/16" (916)

Specify Door Swing LH or RH

Annual Energy Usage 737 kWh | $67*

Shipping Wt (F) 378 lbs (171 kg)

Shipping Wt (O) 378 lbs (171 kg)

Shipping Wt (S/P/B) 406 lbs (184 kg)

F R E E Z E R F E AT U R E S

Automatic Ice Maker

3 Adjustable Wire Shelves

1 Stationary Glass Shelf

3 Freezer Storage Drawers

5 Adjustable Door Shelves

M O D E L 6 0 1 R

A L L R E F R I G E R AT O R

Energy Star Qualified


Framed Design 601R/F

Overlay Design 601R/O

Classic Stainless Steel 601R/S

Platinum Stainless Steel 601R/P

Carbon Stainless Steel 601R/B

S P E C I F I C AT I O N S




Refrigerator Capacity 19.9 cu ft (564 L)








R E F R I G E R A T O R F E AT U R E S

4 Adjustable Glass Shelves


High-Humidity Compartment with Dividers

Adjustable Roll-Out Deli Basket


Adjustable Dairy Compartment

Egg Container

M O D E L 6 0 1 R G

A L L R E F R I G E R AT O RW I T H G L A S S D O O REnergy Star Qualified


Framed Design 601RG/F

Overlay Design 601RG/O

Classic Stainless Steel 601RG/S

Platinum Stainless Steel 601RG/P

Carbon Stainless Steel 601RG/B

















Triple-Pane UV Resistant Glass Door

Optional Accessory Roll-Out Deli BasketAvailable

Egg Container

Optional High Altitude Glass Available**

601RG

M O D E L 6 0 1 R M O D E L 6 0 1 R G M O D E L 6 0 1 F

A C C E S S O R I E SContact your Sub-Zero Dealer

Front panels for framed designin white enamel and classicstainless steel—not available forglass door models

Side panels in white enamel andclassic stainless steel

Extended framed handles

Decorative overlay handles

90˚ and 105˚ door stop kits

Roll-out deli basket(Model 601RG)

Dozen egg container with lid

Harness kit for Star-K compliance

Verify availability with your local dealeror distributor.

*Annual energy costs are based on 9.06cents per kilowatt hour.

**High altitude glass doors are forinstallations at or above 5,000' (1524 m) inelevation and will be treated as a specialorder. Please allow 90 days for delivery.When ordering, add an (HA) before the(G) to obtain the correct model number.

All models are shown in the stainlesssteel design application.



8

M O D E L 6 1 1




Framed Design 611/F

Overlay Design 611/O

Classic Stainless Steel 611/S

Platinum Stainless Steel 611/P

Carbon Stainless Steel 611/B







Min Height Required 83" (2108)






R E F R I G E R AT O R ( D O O R )



High-Humidity Compartment with Divider




Egg Container

F R E E Z E R ( D R A W E R )

Full-Extension Roll-Out Freezer Drawer

Two-Tier Wire Storage Baskets

Automatic Ice Maker

M O D E L 6 1 1 G

O V E R - A N D - U N D E RW I T H G L A S S D O O R


Framed Design 611G/F

Overlay Design 611G/O

Classic Stainless Steel 611G/S

Platinum Stainless Steel 611G/P

Carbon Stainless Steel 611G/B













R E F R I G E R AT O R ( D O O R )






Egg Container





Automatic Ice Maker

M O D E L 6 1 1 M O D E L 6 1 1 G


*Annual energy costs are based on9.06 cents per kilowatt hour.

**High altitude glass doors arefor installations at or above 5,000'(1524 m) in elevation and will betreated as a special order. Pleaseallow 90 days for delivery. Whenordering, add an (HA) before the (G)to obtain the correct model number.



9

M O D E L 6 5 0




Framed Design 650/F

















R E F R I G E R A T O R ( D O O R )







Egg Container




Automatic Ice Maker

M O D E L 6 5 0

M O D E L 6 5 0 G

O V E R - A N D - U N D E RW I T H G L A S S D O O R


Framed Design 650G/F

Overlay Design 650G/O

Classic Stainless Steel 650G/S

Platinum Stainless Steel 650G/P

Carbon Stainless Steel 650G/B



















Egg Container





Automatic Ice Maker

M O D E L 6 5 0 G


Front and grille panels for frameddesign in white enamel andclassic stainless steel


Louvered, panel or stainless steelgrilles in 1" (25) increments from10" (254) to 15" (381) high



Roll-out deli basket (Models 611Gand 650G)



A C C E S S O R I E S

Optional accessoriesare availablethrough yourSub-Zero dealer. Toobtain local dealerinformation, visit theShowroom Locatorsection of ourwebsite,subzero.com.


10

M O D E L 6 8 5

S I D E - B Y - S I D EI C E | W AT E R D I S P E N S I N G


Framed Design 685/F














Shipping Wt (S) 608 lbs (276 kg)




High-Humidity Compartment

1 Storage Drawer




Egg Container


Automatic Ice Maker


1 Stationary Wire Shelf

3 Storage Drawers


2 Juice Can Shelves

M O D E L 6 4 2



Framed Design 642/F

















R E F R I G E R AT O R F E AT U R E S




1 Storage Drawer




Egg Container


Automatic Ice Maker


1 Stationary Solid Shelf

3 Storage Drawers


M O D E L 6 6 1



Framed Design 661/F





















1 Storage Drawer




Egg Container

F R E E Z E R F E A T U R E S

Automatic Ice Maker



4 Storage Drawers


M O D E L 6 6 1 M O D E L 6 4 2 M O D E L 6 8 5



11

M O D E L 6 3 2



Framed Design 632/F





















2 Storage Drawers




Egg Container


Automatic Ice Maker



3 Storage Drawers


M O D E L 6 9 5

S I D E - B Y - S I D EI C E | W AT E R D I S P E N S I N G


Framed Design 695/F



















2 Storage Drawers




Egg Container


Automatic Ice Maker


1 Stationary Wire Shelf

3 Storage Drawers


2 Juice Can Shelves

M O D E L 6 3 2 M O D E L 6 9 5





Front and grille panels for frameddesign in white enamel andclassic stainless steel


Louvered, panel or stainless steelgrilles in 1" (25) increments from10" (254) to 15" (381) high

Framed panel kits (Models 685and 695)*



90˚ and 105˚ door stop kits



*Refer to page 19 for additionalinformation.



12

M O D E L 6 4 8 P R O

S I D E - B Y - S I D EB U I LT - I N O R F R E E - S T A N D I N G




Overall Depth 257/8" (657)






Shipping Weight 860 lbs (390 kg)

R E F R I G E R AT O R(Door and Two Drawers)



2 Adjustable Slide-Out Stainless Steel Bins

1 Crisper Lid

Dividers for Drawers Included

F R E E Z E R(Door and Two Drawers)

Automatic Ice Maker

Water Filtration Filter

3 Adjustable Stainless Steel Shelves

1 Stationary Stainless Steel Shelf

1 Stainless Steel Ice Bucket

M O D E L 6 4 8 P R O G

S I D E - B Y - S I D EW I T H G L A S S D O O RB U I LT - I N O R F R E E - S T A N D I N G











R E F R I G E R A T O R(Door and Two Drawers)



2 Adjustable Slide-Out Stainless Steel Bins

1 Crisper Lid

Dividers for Drawers Included



F R E E Z E R(Door and Two Drawers)

Automatic Ice Maker

Water Filtration Filter

3 Adjustable Stainless Steel Shelves

1 Stationary Stainless Steel Shelf

1 Stainless Steel Ice Bucket

M O D E L 6 4 8 P R O M O D E L 6 4 8 P R O G


**High altitude glass doors arefor installations at or above 5,000'(1524 m) in elevation and will betreated as a special order. Pleaseallow 90 days for delivery. Whenordering, add an (HA) before the (G)to obtain the correct model number.


90˚ door stop kit—right or lefthinge


Slide-out stainless steelrefrigerator bin

Refrigerator drawer dividers

Classic stainless steel side panel

Free-standing kit—includes twostainless steel side panels andtop lid


13


Model 601R36" (914)All Refrigerator

Model 601RG36" (914)All Refrigeratorwith Glass Door

Model 601F36" (914)All Freezer

Model 61130" (762)Over-and-Under

Model 611G30" (762)Over-and-Underwith Glass Door

Model 65036" (914)Over-and-Under

Model 650G36" (914)Over-and-Underwith Glass Door

Model 66136" (914)Side-by-Side


Model 68542" (1067)Side-by-SideIce | Water Dispensing


Model 69548" (1219)Side-by-SideIce | Water Dispensing

Model 648PRO48" (1219)Side-by-SideBuilt-In or Free-Standing

Model 648PROG48" (1219)Side-by-Sidewith Glass DoorBuilt-In or Free-Standing

P L A N N I N G I N F O R M A T I O N

Although the Sub-Zero Built-In line offers a widerange of designs and configurations, the basicplanning considerations for all models havemuch in common. As you integrate Built-Inmodels into your overall plan, review installationrequirements for your particular model(s). TheInstallation Specifications illustrations provideplanning information for all Built-In models—framed, overlay and stainless steel.

Allow the door(s) to open a minimum of 90˚ oryou‘ll have problems removing drawers. With thedoor opening at 90˚, you may have to movedrawers slightly to clear the door interior.

For corner installations, allow for a minimum 3"(76) filler so that the door can open to 90˚. Ifyou‘re using raised panels, consider using awider filler.

When units are installed side by side, a filler stripis recommended. The width of this filler strip willvary depending on the configuration and panelsyou use.

Be sure to add the filler strip width to yourfinished rough opening dimension. In anyinstallation of two units side by side without afiller strip, add an additional 1/2" (13) to yourcombined numbers. This will allow for theproper width.

IMPORTANT NOTE: Refer to the full-scale illus-trations at the end of this section for specificson door openings and filler size alternatives.

E L E C T R I C A L R E Q U I R E M E N T S

A 115 V AC, 60 Hz, 15 amp circuit breaker andelectrical supply are required. A separate circuit,servicing only this appliance, is required.

All Sub-Zero Built-In models are equipped with apower supply cord with a 3-prong groundingplug, which must be plugged into a mating3-prong grounding-type wall receptacle. Followthe National Electrical Code and local codes andordinances when installing the receptacle. Referto the Installation Specifications illustration foryour model on the following pages.

IMPORTANT NOTE: A ground fault circuitinterrupter (GFCI) is not recommended and maycause interruption of operation.

P L U M B I N G C O N S I D E R A T I O N S

For Built-In models with an automatic ice maker,rough in the water supply line. Connect a 1/4"OD copper line to the house supply, being sureto use an easily accessible shut-off valvebetween the supply and the refrigerator.

Do not use self-piercing valves. A saddle valvekit (4200880) is available from your Sub-Zerodealer.

For Built-In models except Models 648PRO and648PROG, a line filter is required when waterconditions have a high sediment content. Theice maker operates on water pressure of 20 psi(1.4 bar) to 100 psi (6.9 bar).

IMPORTANT NOTE: In some cases a reverseosmosis water filter system may not be able tomaintain the minimum water pressure consis-tently.

Models 648PRO and 648PROG come with anautomatic ice maker and an integrated waterfiltration system. This system operates on waterpressure between 35 psi (2.4 bar) and 120 psi(8.3 bar).

IMPORTANT NOTE: A reverse osmosis systemcan be used with Models 648PRO and648PROG, provided there is constant waterpressure of 20 psi (1.4 bar) to 120 psi (8.3 bar)supplied to the unit at all times. In this applica-tion, the integrated water filtration system mustbe set to bypass mode. This is achieved byremoving the water filter cartridge. Refer to thePRO 48 Installation Instructions packed with theunit for detailed instructions.

The water line should be routed up through thefloor within 1/2" (13) from the back wall and nohigher than 3" (76) off the floor. If you have tocome through the wall, make sure the water lineis no more than 3" (76) from the floor.

Regardless of the routing, allow 3' (1 m) ofexcess copper tubing to remain outside the wallor floor for easy connection to the unit. Refer toInstallation Specification illustrations.



14

36"(914)

73"(1854)

36"(914)

73"(1854)

36"(914)

24"(610)

73"(1854)

723/4" (1848)ROUGH OPENING

HEIGHT TOFINISHEDFLOORING

723/4" (1848)MINIMUM HEIGHT

REQUIRED TOFINISHED

FLOORING(LEVELERS IN)

24"(610)

ROUGHOPENING

DEPTH

11"(279)

3"(76)

24"(610)

W

LOCATE WATER SUPPLYWITHIN BOTTOM SHADEDAREA ONLY (601F ONLY)

LOCATE ELECTRICALWITHIN ENTIRE SHADED AREA

6"(152)

E

SHUT-OFFVALVE

EXTENDWATER LINE

APPROX 36" (914)FROM BACK WALL

(601F ONLY)

351/2" (902)ROUGH OPENING WIDTH

FRONT VIEW

TOP VIEW

I N S T A L L AT I O N S P E C I F I C AT I O N SAll Refrigerator | All Freezer Models

Models 601R and 601RG, which do not havean ice maker, will not require the water lineconnection.

Dimensions are for finished rough openings.

Door swing clearances are based onstainless steel door and handle dimensions.

O V E R A L L D I M E N S I O N SAll Refrigerator | All Freezer Models

A L L R E F R I G E R AT O RA L L F R E E Z E R

Model 601RAll Refrigerator

Model 601RGAll Refrigeratorwith Glass Door

Model 601FAll Freezer

361/16"(916)

237/8"(606)

BEHINDFRAME

3/8"(10)FRAME

EXTENSION

90˚

Model 601RAll Refrigerator

Width 36" (914)

Height 73" (1854)

Depth 24" (610)

Model 601RGAll Refrigeratorwith Glass Door

Width 36" (914)

Height 73" (1854)

Depth 24" (610)

Illustrations shown in stainless steel design.

Model 601FAll Freezer

Width 36" (914)

Height 73" (1854)

Depth 24" (610)

Refer to the full-scale illustrations atthe end of thissection for specificson door openingsand otherspecifications.


15

30"(762)

84"(2134)

36"(914)

84"(2134)

30"(762)

84"(2134)

36"(914)

24"(610)

84"(2134)


HEIGHT TOFINISHED

FLOORING WITHSTANDARD

11" (279) GRILLE

83" (2108)MIN HEIGHT

REQUIRED TOFINISHED


751/2"(1918)

7"(178)

6"(152)

AROUGH OPENING WIDTH

24"(610)

ROUGHOPENING

DEPTH

E

3"(76)

18"(457)

W

LOCATE WATER SUPPLYWITHIN SHADED AREA

LOCATE ELECTRICALWITHIN SHADED AREA

6"(152)

SHUT-OFFVALVE

FRONT VIEW

TOP VIEW

EXTENDWATER LINE


I N S T A L L A T I O N S P E C I F I C A T I O N SOver-and-Under Refrigerator /Freezer Models

Model 611

A) Rough Opening Width 291/2" (749)

B) Min Door Clearance 301/8" (765)

Model 611G



Model 650



Model 650G





O V E R A L L D I M E N S I O N SOver-and-Under Refrigerator /Freezer Models


Model 611

Model 611Gwith Glass Door

Model 650


B

237/8"(606)

BEHINDFRAME

3/8"(10)FRAME

EXTENSION

90˚

Model 611

Width 30" (762)

Height 84" (2134)

Depth 24" (610)


Width 30" (762)

Height 84" (2134)

Depth 24" (610)

Model 650

Width 36" (914)

Height 84" (2134)

Depth 24" (610)



Width 36" (914)

Height 84" (2134)

Depth 24" (610)

Refer to installationinstructions shippedwith each Wolfproduct for detailedspecifications.



16

36"(914)

42"(1067)

48"(1219)

42"(1067)

48"(1219)

24"(610)

84"(2134)


HEIGHT TOFINISHED


11" (279) GRILLE

83" (2108)MIN HEIGHT

REQUIRED TOFINISHED


751/2"(1918)

7"(178)

6"(152)

AROUGH OPENING WIDTH

24"(610)

ROUGHOPENING

DEPTH

E

3"(76)

18"(457)

W



6"(152)

SHUT-OFFVALVE

FRONT VIEW

TOP VIEW

EXTENDWATER LINE


I N S T A L L AT I O N S P E C I F I C AT I O N SSide-by-Side Refrigerator | Freezer Models

Model 661



Model 642



Model 685



Model 632



Model 695





O V E R A L L D I M E N S I O N SSide-by-Side Refrigerator | Freezer Models


Model 661

Model 642

Model 685Ice | Water Dispensing

Model 632


B

237/8"(606)

BEHINDFRAME

3/8"(10)FRAME

EXTENSION

90˚

Model 661

Width 36" (914)

Height 84" (2134)

Depth 24" (610)

Model 642

Width 42" (1067)

Height 84" (2134)

Depth 24" (610)


Width 42" (1067)

Height 84" (2134)

Depth 24" (610)

Model 632

Width 48" (1219)

Height 84" (2134)

Depth 24" (610)



Width 48" (1219)

Height 84" (2134)

Depth 24" (610)


17

48"(1219)

7"(178)

6"(152)

ROUGHOPENING DEPTH

24" (610)STANDARD

26" (660)FLUSH

ROUGHOPENING WIDTH

471/2" (1206) STANDARD

48" (1219) FLUSH

E

3" (76)

6"(152)

W



53/16"(132)

SHUT-OFFVALVE

MIN 36" (914)1/4" COPPERWATER LINE

FRONT VIEW

TOP VIEW

ROUGHOPENING HEIGHT

TO FINISHEDFLOORING

833/4" (2127)STANDARD

841/8" (2137)FLUSH

MIN HEIGHTREQUIRED

TO FINISHEDFLOORING

(LEVELERS IN)831/2" (2121)STANDARD

833/4" (2127)FLUSH

751/2"(1918)

I N S T A L L A T I O N S P E C I F I C A T I O N SPRO 48 Side-by-Side Refrigerator | Freezer Models

Built-In or Free-Standing

Models 648PRO and 648PROG can beused free-standing or installed as a standardor flush built-in application. For standardbuilt-in installations, the face frame of theunit will extend 2" (51) beyond cabinetry.In flush built-in installations, the front of theface frame will be flush with surroundingcabinetry.


O V E R A L L D I M E N S I O N SPRO 48 Side-by-Side Refrigerator | Freezer Models

P R O 4 8S I D E - B Y - S I D E

Model 648PROBuilt-In or Free-Standing

Model 648PROGwith Glass DoorBuilt-In or Free-Standing

Model 648PRO

Width 48" (1219)

Height 84" (2134)

Depth 237/8" (606)*257/8" (657)**

Model 648PROGwith Glass Door

Width 48" (1219)

Height 84" (2134)

Depth 237/8" (606)*257/8" (657)**

48"(1219)

84"(2134)

257/8"(657)

305/32"(766)

237/8"(606)

237/8"(606)

BEHINDFACE

FRAME

257/8"(657)

TO FRONTOF FACEFRAME

283/4"(730)

201/2" (521)

48"(1219)

*Depth from behind face frame to back of unit for standard installation.**Depth from front of face frame to back of unit for flush installation.


Refer to the full-scale illustrations atthe end of thissection for specificson door openingsand otherspecifications.



18

A N T I - T I P B L O C K I N G K I T

To prevent the unit from tipping forward and toprovide a stable installation, the unit must besecured in place with an anti-tip blocking kit. Ifthere is a solid soffit above the unit with clear-ance between the unit and the soffit of 1" (25)or less, you won‘t need to block the unit. But forinstallations with clearances of more than 1"(25), you must block the unit with the anti-tipblocking kit (wood block and hardware) providedwith each Sub-Zero Built-In model. Refer to theBuilt-In Installation Instructions packed with theappliance, which provides step-by-step proce-dures for making sure the unit is installedproperly.

A D D I N G P A N E L S

In your plan for panels, be sure you are workingwith the Sub-Zero panel design family called forin your design. If you have chosen the stainlesssteel design, the unit will be shipped completewith wrapped stainless steel doors and handlehardware. You will not have to install doorpanels.

Specifications on the following pages providepanel dimensions and installation considerationsfor framed and overlay door panels.

Side panels can be used with the framed,overlay and stainless steel design applications.Refer to specifications on page 26.

F R A M E D D O O R P A N E L S

If you and your client have ordered a frameddesign model, you will be adding panels to givethe unit the custom Sub-Zero look. The framedpanel design option is available on all Built-Inunits except Models 648PRO and 648PROG. Forexact door panel dimensions for Built-In framedmodels, refer to the Framed Panel Specificationson pages 20–21. Also refer to the full-scaleillustrations at the end of this section for paneland handle considerations.

The traditional framed models come with anelegant, smooth, full-length handle. Optionalextended full-length handles that provideadditional finger clearance for raised panels areavailable through your Sub-Zero dealer.

If the thickness of the custom panels is lessthan 1/4" (6), they must be backed up with asheet of shim material to build the total thick-ness to 1/4" (6). If the panel is thicker than 1/4"(6), an edge must be routed around the panel toensure a proper fit. Refer to illustrations 1 and 2.

IMPORTANT NOTE: On all framed models,routing, recessing or optional extended handlesmay be required on raised panels for finger clear-ance under the handle. Refer to the full-scaleillustrations at the end of this section.

For glass door Models 601RG, 611G and 650G,the refrigerator door panel must include a cut-out to accommodate the window. Refer to theFramed Panel Specifications on pages 20–21.

IMPORTANT NOTE: On glass door models, theglass portion of the door must be exposed andnot covered by any part of the panel.

For Models 685 and 695, the refrigerator doorpanel must include a cut-out to accommodatethe glasswell and bezel. The thickness of thepanel in this area can range from 1/4" (6) to amaximum of 11/8" (29). If the panel is thicker,provisions must be made to rout out a space toaccommodate the decorative bezel surroundingthe glasswell.

PANELS THICKER THAN 1/4" (6)

Trim reveal 1/4" (6) min

Rout to 1/4" (6)thickness

PANELS 1/4" (6) THICK OR LESS

1/4" (6) Panel

Trim reveal 1/4" (6) min

Illus. 2Illus. 1




19

G L A S S W E L L P A N E L O P T I O N S

If you choose not to use custom wood panelsabove or below the glasswell for Model 685 or695 framed application, a stainless steel insertpanel will be provided with the partial framedaccessory kit. This accessory kit (FRAMPAR),includes partial framed molding and classicstainless steel inset handle panel to provide aspill-resistant finish above and below the glass-well on the refrigerator door only. Refer to theFramed Panel Specifications for this option onpage 21.

With the framed retrofit accessory kit, existingModel 680 or 690 door panels can be used on anew Model 685 or 695 framed unit. This acces-sory kit (FRAMRET) includes framed retrofitmoldings and classic stainless steel inset handlepanels to accommodate existing Model 680 or690 framed refrigerator and freezer door panels.

IMPORTANT NOTE: When using Model 680 or690 raised panels with the framed retrofit kit(FRAMRET), a 1/2" (13) trim reveal down to 1/4"(6) thickness is necessary at the bezel in orderfor the panels to fit properly.

Both accessory kits are available through yourSub-Zero dealer. Refer to the illustrations below.

O P T I O N A L P A N E L G R I L L E

An 11" (279) louvered grille is standard onframed applications. Optional louvered grilles areavailable in 1" (25) height increments from 10"(254) to 15" (381) for all Built-In models exceptModels 601R, 601RG, 601F, 648PRO and648PROG.

You may choose to use Sub-Zero‘s optionalpanel grille for some of your framed applications.The panel grilles can be used with all Built-Inmodels except Models 601R, 601RG, 601F,648PRO and 648PROG and are available in 1"(25) height increments from 10" (254) to 15"(381).

For each model, the width of the panel grille willbe the same, regardless of the height you havechosen. To determine the panel grille insert size,use the width dimension listed for your modeland the height dimension for the grille optionyou have chosen. Specifications for the PanelGrille Option are listed on page 21.

Partial Framed KitFRAMPAR

Framed Retrofit KitFRAMRET

P A N E LR E Q U I R E M E N T S

The weight ofeach framed doorpanel cannot exceed50 lbs (23 kg).

F R A M E D P A N E L S

To install framedpanels, see thedetailed proceduresoutlined in theSub-Zero Built-InInstallationInstructions.



20

C

C C

H

W

H

A

B

D

14"(356)

H

W

H

A

B

14"(356)

F R A M E D D O O R P A N E L S P E C I F I C AT I O N SAll Refrigerator | All Freezer Framed (F) Models

Model 601R W H

Refrigerator Framed Panel 341/8" (867) 5815/16" (1497)

Raised Panel Handle Recess Location –

Refrigerator Panel A) 2915/32" (749)

Model 601RG W H




Window Cut-Out Dimensions 253/8" (645) 413/16" (1046)

Window Cut-Out Location C) 43/8" (111) D) 133/8" (340)

Model 601F W H

Freezer Framed Panel 341/8" (867) 5815/16" (1497)


Freezer Panel A) 2915/32" (749)

IMPORTANT NOTE: Panel specifications are for Built-In framed (F)models. Panel specifications for overlay models are on pages 24–25.

F R A M E D D O O R P A N E L S P E C I F I C A T I O N SOver-and-Under Framed (F) Models

Model 611 W H





Freezer Panel B) 141/16" (357)

Model 611G W H








Model 650 W H






Model 650G W H









Models 601Rand 601F

Model 601RG

Models 611 and 650 Models 611G and 650G

C

W

H

A

C C

D

14"(356)

W

H

A

14"(356)


Panel specificationsare for Built-Inframed (F) models.


21

P A R T I A L F R A M E D D O O R P A N E L O P T I O NIce | Water Dispensing Framed (F) Models

Model 685 W H

Refrigerator Partial Framed Panel 155/8" (397) 6711/16" (1719)

Freezer Partial Framed Panel 155/8" (397) 6711/16" (1719)

Model 695 W H

Refrigerator Partial Framed Panel 1715/16" (456) 6711/16" (1719)

Freezer Partial Framed Panel 1715/16" (456) 6711/16" (1719)

The partial framed accessory kit (FRAMPAR) is required for this option.Kit includes partial framed molding and classic stainless steel insethandle panels for above and below glasswell on the refrigerator door.

P A N E L G R I L L E O P T I O NFramed (F) Models

Models 611 and 611G W

Grille Panel Width 283/16" (716)

Models 650, 650G, 661 W


Models 642 and 685 W




10" (254) Grille H

Grille Panel Height 815/16" (227)

11" (279) Grille (standard) H


12" (305) Grille Height H


13" (330) Grille H


14" (356) Grille H


15" (381) Grille H


For panel grille insert size, use width dimension listedfor your model and height dimension for grille option.11" (279) grille is standard.

F R A M E D D O O R P A N E L S P E C I F I C AT I O N SSide-by-Side Framed (F) Models

Model 661 W H




Refrigerator | Freezer Panel A) 385/32" (969)

Model 642 W H

Refrigerator Framed Panel 24" (610) 6711/16" (1719)




Model 685 W H

Refrigerator Framed Panel 24" (610) 6711/16" (1719)


Glasswell Cut-Out Dimensions 57/8" (150) 127/16" (315)

Glasswell Location (Refrigerator) E) 19/16" (39) F) 289/16" (726)

Model 632 W H





Model 695 W H




Glasswell Location (Refrigerator) E) 19/16" (39) F) 289/16" (726)


For Models 685 and 695, panel thickness in the glasswell area canrange from 1/4" (6) to a maximum of 11/8" (29). If the panel is thicker,you must rout out a minimum 1/4" (6) flat landing area to accommo-date the bezel surrounding the glasswell.

Models 661, 642and 632

WW WW

H14" (356)

WW

H

A

H

F

E

Models 685 and 695 Models 685 and 695Partial Framed Option


To install framedpanels, see thedetailed proceduresoutlined in theSub-Zero Built-InInstallationInstructions.


22

IMPORTANT NOTE: Keep in mind that theSub-Zero door panels have the potential forhitting adjacent cabinets and/or countertopswhen they are opened. You need to be aware ofyour surrounding cabinetry and space limitationswhen using the overlay models. Refer to the full-scale illustrations at the end of this section.

If you are using an overlay door panel withModel 611, 611G, 650 or 650G, it is necessaryto rout a space for the unit‘s lower hinge plateso it does not strike the door panel. Refer toillustration 5.

For Models 611, 611G, 650 and 650G, you willminimize the reveal between the bottom of theoverlay door panel and the top of the overlaydrawer panel. Refer to illustration 6.

IMPORTANT NOTE: If you choose not to rout aspace for the lower hinge plate, you can reducethe total height of the overlay panel (decorativepanel only) by 1/2" (13).

Overlay Panel

5/16"(8)

17/32"(13)

27/32"(21)

Spacer Panel

BackerPanel

1/4"(6) Backer Panel

Overlay Panel

3" (76)

Bottom Edge –Hinge Side(rear view)

Spacer Panel

3/8" (10)

1/2"(13)

Illus. 5 Illus. 6

Do not exceed the overlay decorative panel

dimensions for Models 611, 611G, 650 or

650G listed on page 24. If you try to make

the reveal tighter between the door and

drawer panels, the panels may hit when

opening and closing, causing possible

damage to the panels and the Sub-Zero unit.

O V E R L A Y D O O R P A N E L S

If you and your client have ordered an overlaydesign model, you will be adding panels to givethe unit the custom Sub-Zero look. The overlaypanel design option is available on all Built-Inunits except Models 648PRO and 648PROG.

For exact door panel dimensions for Built-Inoverlay models, refer to the Overlay Panel Speci-fications on pages 24–25.

The overlay design allows decorative panels tocover the door trim for a more seamlessappearance that blends with the design of theroom. To achieve this look, the most commonway is to work with three panels—the decorativeoverlay panel, a 0.10" (3) spacer panel and a 1/4"(6) backer panel. Depending on your cabinetmanufacturer, this could be one panel routed fordifferent dimensions or, more likely, three differ-ent panels.

Regardless of the physical construction of thepanels (routing or three-panel assembly), you willneed to follow the Overlay Panel Specificationson the following pages for exact sizing and panelplacement to ensure a proper fit.

Illustration 3 is a cross section view of the three-panel assembly showing placement of the door,drawer or grille trim. Illustration 4 shows a rearview of the three-panel assembly and criticaldimensions, standard for all models.

Spacer PanelOverlay Panel

1/4" (6)

BackerPanel

.10" (3)

~3/4"(19)

Door/Drawer/Grille Trim1/16" (2)

5/32" (4)

1/4" (6) Backer Panel5/16" (8) min

.10"(3)

Spacer Panel

Overlay Panel

Illus. 4Illus. 3


The overlay doorpanel assembly mustbe a minimum of5/8" (16) thick andcannot exceed 50 lbs(23 kg).



23

Illustration 8 shows how you can box out alanding space for the bezel using stiles and railsto create this space. Again, keep in mind, thatthe total thickness of the panel at this level mustnot exceed 11/8" (29).

O V E R L A Y P A N E L G R I L L E

Overlay grille panels for the panel grille matchthe design of the door panels. Overlay units,except Models 601R, 601RG and 601F, comestandard with an 11" (279) panel grille. Optionalgrilles are available in 1" (25) height incrementsfrom 10" (254) to 15" (381). Overlay grille panelspecifications for the panel grille are listed onpage 25. Also refer to illustration 4 on page 22for additional overlay panel dimensions.

Do not exceed the panel dimensions listed

for the appropriate overlay grille panel you

are specifying. The decorative panel cannot

be any larger or it may restrict the airflow

to the compressor area and cause problems

with the operation of the Sub-Zero unit.

O V E R L A Y D O O R P A N E L S

For glass door Models 601RG, 611G and 650G,the refrigerator door panel must include a cut-out to accommodate the window. Refer to theOverlay Panel Specifications for Models 601RG,611G and 650G on page 24.

IMPORTANT NOTE: On glass door models, theglass portion of the door must be exposed andnot covered by any part of the panel.

For Models 685 and 695, the refrigerator doorpanel must include a cut-out to accommodatethe glasswell and bezel. The thickness of thepanel in this area can range from 1/4" (6) to amaximum of 11/8" (29).

IMPORTANT NOTE: Regardless of the thicknessof the overlay panel for Model 685 or 695, youmust plan for a flat ’landing’ space for thedecorative bezel surrounding the glasswell area.Refer to page 25 for exact cut-out dimensions ofthe glasswell area in the overlay, spacer andbacker panels. This ’landing’ area can be accom-plished in a number of different ways. We areshowing two in Illustrations 7 and 8 below.

Illustration 7 shows how you can recess thebezel to the inset panel. You must rout out aspace to accommodate the 127/8" (327) heightof the bezel. Also keep in mind that the amountof material you will rout out of the stile will varybecause of the thickness of this element.However, the width of the stile immediatelyadjacent to the bezel must be 17/16" (37). DONOT cut the entire stile to this dimension. In thisillustration you can see that rails above andbelow the bezel give this a finished look. Makesure that the bezel is not supporting weightfrom the panel.

O V E R L A Y P A N E L S

To install overlaypanels, see thedetailed proceduresoutlined in theSub-Zero Built-InInstallationInstructions.

2" (51)Edge ofPanel toCut-Out

Glasswell Cut-Out

17/16" (37) Widthof Stile

Adjacentto Bezel

RoutingRequired

127/8"(327)

Heightof Bezel

Illus. 8Illus. 7



24

C

C C

H

W

H

D

H

W

H

C

W

H

C C

D

W

H

O V E R L A Y D O O R P A N E L S P E C I F I C AT I O N SAll Refrigerator | All Freezer Overlay (O) Models

Model 601R W H

Refrigerator Overlay Panel 347/16" (875) 591/4" (1505)

Refrigerator Spacer Panel 331/2" (851) 585/16" (1481)

Refrigerator Backer Panel 341/8" (867) 5815/16" (1497)

Model 601RG W H






Model 601F W H

Freezer Overlay Panel 347/16" (875) 591/4" (1505)

Freezer Spacer Panel 331/2" (851) 585/16" (1481)

Freezer Backer Panel 341/8" (867) 5815/16" (1497)

IMPORTANT NOTE: Panel specifications are for Built-In overlay (O)models. Panel specifications for framed models are on pages 20–21.

O V E R L A Y D O O R P A N E L S P E C I F I C AT I O N SOver-and-Under Overlay (O) Models

Model 611 W H







Model 611G W H








Window Cut-Out Location C) 41/2" (114) D) 5" (127)

Model 650 W H







Model 650G W H








Window Cut-Out Location C) 41/2" (114) D) 5" (127)


Models 611 and 650 Models 611G and650G

Model 601RGModels 601Rand 601F


Panel specificationsare for Built-Inoverlay (O) models.


25

O V E R L A Y G R I L L E P A N E LOverlay (O) Models

Width Dimensions

Models 611 and 611G W

Overlay Panel Width 287/16" (722)

Spacer Panel Width 271/2" (699)

Backer Panel Width 281/8" (714)

Models 650, 650G, 661 W












Height Dimensions

10" (254) Grille H

Overlay Panel Height 91/4" (235)

Spacer Panel Height 85/16" (211)

Backer Panel Height 815/16" (227)

11" (279) Grille (standard) H




12" (305) Grille Height H




13" (330) Grille H




14" (356) Grille H




15" (381) Grille H




For grille panel size, use width dimensionslisted for your model and height dimensionsfor grille option. 11" (279) grille is standard.

Panel grille is available for all overlay unitsexcept Models 601R, 601RG and 601F.

O V E R L A Y D O O R P A N E L S P E C I F I C A T I O N SSide-by-Side Overlay (O) Models

Model 661 W H

Refrigerator Overlay Panel 197/16" (494) 68" (1727)



Freezer Overlay Panel 1415/16" (379) 68" (1727)

Freezer Spacer Panel 14" (356) 671/16" (1703)


Models 642 and 685 W H

Refrigerator Overlay Panel 245/16" (618) 68" (1727)


Refrigerator Backer Panel 24" (610) 6711/16" (1719)


Freezer Spacer Panel 15" (381) 671/16" (1703)


Models 632 and 695 W H

Refrigerator Overlay Panel 28" (711) 68" (1727)






Glasswell Cut-Out –Models 685 and 695 W H


Glasswell Location (Overlay) E) 111/16" (43) F) 283/4" (730)

Glasswell Location (Spacer) E) 11/4" (31) F) 281/4" (718)

Glasswell Location (Backer) E) 19/16" (39) F) 289/16" (726)


For Models 685 and 695, panel thickness in the glasswell area canrange from 1/4" (6) to a maximum of 11/8" (29). If the panel is thicker,you must rout out a minimum 1/4" (6) flat landing area to accommo-date the bezel surrounding the glasswell.


To install overlaypanels, see thedetailed proceduresoutlined in theSub-Zero Built-InInstallationInstructions.

WW

H

Models 661, 642and 632

Models 685 and 695

WW

H

E

F

26


H A N D L E H A R D W A R E

Overlay models come without handle hardware.The beauty of this design is that you can matchthe surrounding cabinet hardware. You or thecabinet manufacturer must provide handlehardware to match the overall decoratingscheme.

The handle hardware must be installed beforeinstalling the panel assembly. Use larger D-stylehandles. If screws with thick heads are used,the screws will need to be countersunk into thedoor before the panel is put into place.

IMPORTANT NOTE: Sub-Zero does not recom-mend using single pull knobs on any of its Built-In models.

For overlay Models 685 and 695, mountingplacement of the refrigerator door handle mustassure proper access to the glasswell andadequate clearance under the handle. Illustration9 shows placement of the refrigerator doorhandle in relationship to the glasswell bezel onstainless steel models.

Optional stainless steel handles are available in avariety of diameters and lengths, as are handlesto match the color and style of Wolf ovens.Contact your Sub-Zero dealer for specifics.

Refer to the full-scale illustrations at the end ofthis section for handle hardware considerations.

S I D E P A N E L S

Side panels can be used with the framed,overlay and stainless steel design applications.When planning for side panels with the installa-tion of a Built-In model, you need to be aware ofspace configuration to achieve a pleasing fit.Depending on the exact panel you are using withyour unit, the height of the panel will vary.

Cut-outs around the toe kick and grille area arerequired if a 1/4" (6) thick panel will be insertedinto the main frame channel. The panel will needto be 24" (610) deep. If a 3/8" (10) thick panel isused, the panel will abut the main frame andshould be 237/8" (606) deep. Refer to illustra-tions 10–12 below for placement of toe kick andgrille area cut-outs for your specific model.These dimensions do not apply to Models648PRO and 648PROG.

The toe kick area may or may not be cut outdepending on the look you want to achieve.

IMPORTANT NOTE: The use of side panels maychange the width of your rough opening.

4" (102)

3" (76)

237/8" (606)BEHIND FRAME

Illus. 10—Models 601R,601RG and 601F

2"(51)

GlasswellProfile

HandleProfile

1"(25)

Illus. 9



131/4" (337)

4" (102)

1/4" (6)

1/4" (6)

3" (76)

3" (76)


Illus. 12—Models 661, 642, 632,685 and 695

131/4" (337)

4" (102)

1/4" (6)

3" (76)


Illus. 11—Models 611, 611G,650 and 650G



27

F U L L - S C A L ET E M P L AT E S

The full-scaleillustrations on thefollowing pagesenable you to under-stand some of theunique situationsyou may face as youplan for the installa-tion of the Built-Inmodels. Use theseillustrations astemplates forpanel and handlehardwareconsiderations.

P A N E L A N D H A N D L E P R O F I L E – F R A M E D A P P L I C A T I O N

11/4"(32) PANEL

1"(25) PANEL

1/4"(6) PANEL

1/2"(13) PANEL

3/4"(19) PANEL

OPTIONALEXTENDED

FULL-LENGTHHANDLE

STANDARD FULL-LENGTH

HANDLE

DOOR

1/4"(6) FRAMED PANEL

1"(25)

2"(51)

3"(76)

The full-scale illustration above showshandle placement for the framed appli-cation standard full-length handle andthe optional extended full-length handleshown in the dashed line.



28

P A N E L A N D H A N D L E P R O F I L E – O V E R L A Y A N D S T A I N L E S S S T E E L A P P L I C A T I O N

11/4" (32) PANEL

1" (25) PANEL

1/4" (6) PANEL

1/2" (13) PANEL

3/4" (19) PANEL5/8" (16) PANEL

DOOR

1/4" (6) APPROXIMATE THICKNESS OF WRAPPED STAINLESS STEEL DOOR

NOTE: FOR OVERLAY APPLICATIONS, OPTIONAL STAINLESS STEEL HANDLEMUST BE MOUNTED ON PANEL MINIMUM 5/8" (16) THICK.

1"2"

(51)3"

(76)

STANDARD STAINLESS STEEL HANDLE

The full-scale illustration above showshandle placement for the standardstainless steel handle on the wrappedstainless steel door and on overlaypanel applications shown in the dashedline.

IMPORTANT NOTE: For overlay applica-tions, the panel must be a minimum of5/8" (16) thick to support mounting thehandle hardware.

For overlay applications, mount doorhandles close to the opening edge ofthe door for ease of opening.


29

11 /4"

(32)

PANEL

1"(2

5)PA

NEL

*1/4"

(6) PA

NEL

1 /2"(1

3)PA

NEL

3 /4"(1

9)PA

NEL

130˚ DOOR OPENINGWITH 2" (51) FILLER STRIP

(TOP VIEW)

OPTIONALFRAMED EXTENDED

FULL-LENGTH HANDLE

STANDARDFRAMED

FULL-LENGTHHANDLE

DOOR CLOSED

DOOR OPEN @ 130˚

HINGE

2" (51)

FILLER STRIP

MAIN FRAME

ALLOW FOR FILLER LAPBEHIND FLANGE

APPROXPROFILE OFSTAINLESS

STEEL DOORAND HANDLE

OVERLAY PANEL3/4" (19) THICK

(NOMINAL)

SUB-ZERO UNITSUB-ZERO UNIT

The full-scale illustration shows thepanel and handle profile for 130˚ dooropening with a 2" (51) filler strip.

Interference of door panels withhandles at maximum door swing mayrequire the use of an optional 90˚ doorstop available through your Sub-Zerodealer.

P A N E L A N D H A N D L E P R O F I L E – 1 3 0 ˚ D O O R O P E N I N G ( T O P V I E W )

*Approximate thickness of wrappedstainless steel door.



30

11/4

"(3

2)PA

NE

L

1"(2

5)PA

NE

L

*1/4

"(6

)PA

NE

L

1 /2"

(13)

PAN

EL

3 /4"

(19)

PAN

EL

11/4" (32)

11/2" (38)

13/4" (44)

0" (0)

1" (25)

2" (51)

21/4" (57)

21/2" (63)

23/4" (70)

3" (76)

31/4" (83)

31/2" (89)

1/4" (6)

1/2" (13)

3/4" (19)HINGE

OVERLAY PANEL 3/4" (19) THICK (NOMINAL)

DOOR CLOSED

DOOR OPEN @ 90˚

90˚ DOOR OPENING(TOP VIEW)

MAIN FRAME

NOMINAL OVERALL WIDTH OF SUB-ZERO

SUB-ZERO UNIT

237/8" (606) TO REAROF SUB-ZERO

O V E R L A Y P A N E L A P P L I C A T I O N – 9 0 ˚ D O O R O P E N I N G ( T O P V I E W )

The full-scale illustrationshows what considera-tions you need to makefor overlay panel appli-cations and how theymay interact withadjacent cabinets andcountertops.

*Approximate thickness of wrappedstainless steel door.

I N T E G R A T E D R E F R I G E R A T I O N

31


For generations, the Sub-Zero name has beensynonymous with built-in refrigeration. With theIntegrated line, we have taken the idea a stepfurther—refrigerators and freezers you can hideanywhere in the house, inside the furniture orcabinetry of your choosing.

Created to blend invisibly into your home‘sdecor, the Integrated line lets you integraterefrigeration into the kitchen, master suite, mediaroom or workout room. Available as tall units ortwo-drawer base units, the Integrated lineexpands the possibilities for the way you shapeyour home.

Tall units are 80" (2032) high and offered in twodifferent widths—27" (686) and 36" (914). The27" (686) wide tall unit can be ordered as an allrefrigerator, all freezer or combination refrigerator(upper cabinet) and freezer (drawers). The 36"(914) wide tall unit is offered as an all refrigera-tor or combination unit. All of these models are24" (610) deep.

Base units are offered in the 27" (686) widthonly. They can be ordered as an all refrigerator,all freezer or combination refrigerator (topdrawer) and freezer (bottom drawer). Base unitsare 341/2" (876) high and 24" (610) deep.

You just need to add whatever beautiful cabi-netry you want to use. Optional stainless steelpanels with tubular handles are offered in theclassic, platinum and carbon stainless steelfinishes and are ordered and shipped as salesaccessories. There are some size limitations onthe premium finishes of platinum and carbonstainless steel.

For information regarding specific Integratedmodels, refer to the illustrations in this section.

27"(686)

80"(2032)

27"(686)

80"(2032)

27"(686)

80"(2032)

36"(914)

80"(2032)

341/2"(876)

27"(686)

341/2"(876)

27"(686)

341/2"(876)

27"(686)

With the installation of a harness kit,tall models are Star-K compliant to meetstrict religious regulations in conjunctionwith specific instructions found onwww.star-k.org. Drawer models areStar-K certified from the factory withno extra wiring harness required. Fordetails about the harness kit, contactyour Sub-Zero dealer.

A L L R E F R I G E R AT O R | A L L F R E E Z E R


D R A W E R S

M O D E L 7 0 0 T R

All Refrigerator

M O D E L 7 0 0 T F ( I )

All Freezer

M O D E L 7 0 0 T C ( I )

Refrigerator | Freezer

M O D E L 7 3 6 T C ( I )


M O D E L 7 0 0 B R

All Refrigerator


M O D E L 7 0 0 B F ( I )

All Freezer

M O D E L 7 0 0 B C ( I )


36"(914)

80"(2032)

M O D E L 7 3 6 T R

All Refrigerator

NEW



32

M O D E L 7 3 6 T R










Drawer Clearance 191/2" (495)



R E F R I G E R AT O R F E AT U R E S

Dual Refrigeration

2 Temperature Zones


1 Stationary Shelf

2 Storage Drawers

Removable Crisper Cover

4 Removable Drawer Dividers

Adjustable Deli Drawer



Egg Container

P A N E L O P T I O N S

Integrated

Classic, platinum or carbon stainlesssteel finish (includes handles)**

M O D E L 7 0 0 T F

A L L F R E E Z E R


Automatic Ice Maker 700TFI












F R E E Z E R F E A T U R E S

1 Temperature Zone


1 Stationary Shelf

2 Storage Drawers

2 Removable Drawer Dividers (700TF)

1 Removable Drawer Divider (700TFI)


Automatic Defrost

Automatic Ice Maker Model 700TFI


Integrated


M O D E L 7 3 6 T R M O D E L 7 0 0 T F ( I )

M O D E L 7 0 0 T R














Dual Refrigeration

2 Temperature Zones


1 Stationary Shelf

2 Storage Drawers






Egg Container


Integrated


M O D E L 7 0 0 T R

NEW



33

M O D E L 7 3 6 T C



Automatic Ice Maker 736TCI














Dual Refrigeration


1 Stationary Shelf

High-Humidity Crisper Drawer with Dividers



Egg Container

F R E E Z E R ( D R A W E R S )

2 Removable Drawer Dividers (736TC)

1 Removable Drawer Divider (736TCI)

Automatic Defrost

Automatic Ice Maker (736TCI)


Integrated


M O D E L 7 0 0 T C



Automatic Ice Maker 700TCI














Dual Refrigeration


1 Stationary Shelf




Egg Container

F R E E Z E R ( D R A W E R S )

2 Removable Drawer Dividers (700TC)

1 Removable Drawer Divider (700TCI)

Automatic Defrost

Automatic Ice Maker (700TCI)


Integrated


M O D E L 7 0 0 T C ( I ) M O D E L 7 3 6 T C ( I )


**Optional stainless steel panels andhandles are ordered and shipped assales accessories. For additionalinformation on panel and handle sizesand applications, check our website,subzero.com.


Classic stainless steel frontpanels—platinum and carbonavailable in certain sizes

Tubular handles in classic,platinum and carbon stainlesssteel

High-humidity crisper drawer andshelf assembly*

Adjustable deli drawer and shelfassembly*

Crisper cover with lid*

Dozen egg container with lid*

Dual installation heater kit


*Accessory is not available forevery model.



34

M O D E L 7 0 0 B C

R E F R I G E R AT O R | F R E E Z E RD R A W E R S


Automatic Ice Maker 700BCI



Overall Height 341/2" (876)








F E A T U R E S

2 Temperature Zones

2 Storage Drawers


1 Removable Drawer Divider (700BC)

Automatic Ice Maker (700BCI)


Integrated


M O D E L 7 0 0 B R

R E F R I G E R A T O R D R A W E R S












1 Temperature Zone

2 Storage Drawers




Integrated


M O D E L 7 0 0 B F

F R E E Z E R D R A W E R S


Automatic Ice Maker 700BFI











1 Temperature Zone

2 Storage Drawers

2 Removable Drawer Dividers (700BF)

1 Removable Drawer Divider (700BFI)

Automatic Defrost

Automatic Ice Maker (700BFI)


Integrated


M O D E L 7 0 0 B R M O D E L 7 0 0 B F ( I ) M O D E L 7 0 0 B C ( I )


**Optional stainless steel panels andhandles are ordered and shipped assales accessories. For additionalinformation on panel and handle sizesand applications, check our website,subzero.com.


Front panels in classic, platinumand carbon stainless steel

Tubular handles in classic, platinumand carbon stainless steel

Crisper cover with lid*

Dozen egg container with lid*

Dual installation heater kit

*Accessory is not available forevery model.


35



T E M P E R AT U R E Z O N E S

Model 700BR – One zone,34˚F (1˚C) to 45˚F (7˚C)

Models 700TR and 736TR –Two zones, 34˚F (1˚C) to 45˚F (7˚C)

Models 700BF(I) and 700TF(I) –One zone, -5˚F (-21˚C) to +5˚F (-15˚C)

Model 700TF(I) – One zone,-5˚F (-21˚C) to +5˚F (-15˚C)

Model 700BC(I) – Two zones,34˚F (1˚C) to 45˚F (7˚C) top drawer;-5˚F (-21˚C) to +5˚F (-15˚C) bottomdrawer

Models 700TC(I) and 736TC(I) –Two zones, 34˚F (1˚C) to 45˚F (7˚C)cabinet; -5˚F (-21˚C) to +5˚F (-15˚C)drawers

I N T E G R A T E D F E A T U R E S

All Integrated models accept wood or stainlesssteel panels. The optional stainless steel panelsand handles are available in classic, platinum andcarbon stainless steel finishes at the 80" (2032)height, and only classic stainless steel at the 84"(2134) height. Stainless steel panels are orderedand shipped as sales accessories.

Functional Design. These models can be placedanywhere in the home. Think about “point-of-use refrigeration” when planning where to placeyour units.

Integrated Design. All Sub-Zero models are 24"(610) deep. Tall Integrated units are 80" (2032)high and are offered in two different widths—27" (686) and 36" (914). All base units are 27"(686) wide and 341/2" (876) high.

Microprocessor. The “brains” of the Integratedunits, this computer allows the best in tempera-ture control, efficiency and food preservation.

Temperature Zones. On tall refrigerator andcombination units, you have the flexibility ofhaving two temperatures within the same unit.

Automatic Defrost. Depending on usage andexact climate, the Integrated unit will adapt tothe unique situation and adjust accordingly tooffer greater efficiency. Integrated freezer andcombination units have an automatic defrostsystem.

Kickplate. The adjustable solid kickplate meetsstandards of the American Institute of Archi-tects. The toe kick area for a solid, decorativekickplate is 4" (102) high by 3" (76) deep. Youcan show a 10" (254) toe kick, but you cannotcover the louvers of the kickplate. If you choose,the kickplate can be painted.

Front Venting. All models have the mechanicalequipment in an area below the lower drawer.The lower drawer panel can extend to coverthese louvers, but a removable decorative kick-plate cannot cover the fins.

Lighting. Flat to the ceiling, superior lightingprovides white, efficient light in cabinet anddrawer units.

Door/Drawer Alarm. When activated, if yourdoor or drawer is accidentally left open for morethan 30 seconds, an audible alarm will sound.

Spill-Proof Shelves. The cabinet section of thetall units features adjustable spill-proof one-pieceglass shelves that are easily removed forcleaning.

Dairy Shelf. This magnetically sealed compart-ment is fully adjustable on the tall refrigerator andcombination units.

Crisper Cover. On the tall and base refrigeratorunits and the base combination unit, a removablecrisper cover is offered for one of the drawersections.

Deli Drawer. Smaller items are not lost in thishandy feature of the Models 700TR and 700TC(I).Available as a sales accessory for Model 736TC(I).

Crisper—Model 736TC(I). Model 736TC(I) isequipped with a sealed crisper. It is large anddeep, with smooth sides for easy cleaning. Thespace features removable dividers.

Egg Container. You can store a dozen eggs inthis removable egg container with lid in the tallrefrigerator and tall combination units.

Ice Maker. An automatic ice maker, providingcrescent-shaped ice, is available as an option onthe tall and base freezers as well as the tall andbase combination units. This optional equipmentmust be factory installed.

Door Swing. You can choose left or right doorswing on the tall units. This option must beordered when requesting the unit. You cannotreverse the door in the field.

Dual-Action Hinge. An exclusive dual-actionhinge is featured on all of the tall units, allowingfor a fully integrated look.

Door Stop. On all of the tall units, a 90˚ door stopis built in to the hinge. Normal door swing is 105˚.

Temperature Zones. With the microprocessor inthe Integrated models, you have the capability ofsetting different optimum temperatures.



36


Before moving the Integrated unit into place, besure that the finished opening dimensions, elec-trical and plumbing locations and minimum doorand drawer clearances are accurate. Refer to theInstallation Specifications illustration for yourmodel on the following pages. Be sure yourinstaller has this information before finishingwork is completed.

Integrated models without an automatic icemaker will not require the plumbing connectionsshown in the illustrations.

The height of the tall unit is set at 80" (2032).You can allow the top of the door panel toexceed this dimension with caution. If you areworking with 84" (2134) or 96" (2438) neighbor-ing panels, you can utilize door panels to matchthis height. Other critical dimensions regardingthe door swing, drawer openings and toe kickclearance are noted in the Overall Dimensionsillustrations on the following pages. Also refer tothe full-scale illustrations at the end of thissection for specifics on door openings and otherspecifications.

IMPORTANT NOTE: The anti-tip bracket must beinstalled to prevent the unit from tippingforward.


A 115 V AC, 60 Hz, 15 amp circuit breaker andelectrical supply are required. A separate circuit,servicing each base and tall unit, is required.

All Sub-Zero Integrated models are equippedwith a power supply cord with a 3-pronggrounding plug, which must be plugged into amating 3-prong grounding-type wall receptacle.Follow the National Electrical Code and localcodes and ordinances when installing thereceptacle.

IMPORTANT NOTE: The electrical outlet mustbe placed so the grounding prong is to the rightof the thinner blades. The outlet must be flushwith the back wall. Refer to the InstallationSpecifications illustration for your model forexact placement.


Do not use an extension cord or 2-prong

adapter. Electrical ground is required.

Do not under any circumstances remove

the power supply cord ground prong.

P L U M B I N G C O N S I D E R A T I O N S

For models with an automatic ice maker, roughin the water supply line. Connect a 1/4" ODcopper line to the house supply, being sure touse an easily accessible shut-off valve betweenthe supply and the unit. This shut-off valveshould not be installed behind the unit.

Do not use self-piercing valves. A saddle valvekit (4200880) is available from your Sub-Zerodealer. An in-line filter is required when waterconditions have a high sediment content. The icemaker operates on constant water pressurebetween 20 psi (1.4 bar) and 100 psi (6.9 bar).

IMPORTANT NOTE: In some cases, a reverseosmosis water filter system may not be able tomaintain the minimum pressure consistently.

The Installation Specifications illustration foryour model on the following pages shows theprecise placement of the water line. Whenrouting the water through the side walls, youmust place the water line within 1/2" (13) of thefloor and as close as possible to the back wall.The line must be routed around the anti-tipbracket so it clears the bracket and the levelingfeet of the unit as shown in the top view of theillustration. Regardless of the routing, allow for27" (686) of excess copper tubing to remainoutside the wall or floor for easy connection tothe unit.

IMPORTANT NOTE: Do not route water supplyline in front of the compressor tray. The traymust be slid forward for service.


37

TOP OFROUGH

OPENING

789/16"*(1995)

341/2"*(876)

14"(356)

13/16"(21)

93/4"(248)

4"(102)

80"*(2032)

27"(686)

24"(610)

*1/2" (13) +_ ADJUSTMENT IN LEVELING LEGS

FRONT VIEW SIDE VIEW

(UNIT DIMENSION) (UNIT DIMENSION)

3/8"(10)

131/4"(337)1/2"

(13)

101/4"(260)

203/8"(518)

DOORMOUNTING

DETAIL

DRAWERMOUNTING DETAIL

105˚90˚

90˚ DOOR OPENING

DOOR/DRAWERCLOSED

MAXIMUM DOOR OPENING

*DOOR/DRAWER PANEL THICKNESS NOT INCLUDED – DIMENSION WILL VARY WITH INSTALLATION

DOOR/DRAWERCLOSED

191/2"*(495)251/2"*

(648)

24"(610)

257/8" (657)

45/8"* (117)

TOP VIEW

25"(635)

27"(686)

80"(2032)

27"(686)

25"(635)

ANTI-TIPBRACKET*

WATER LINEBOTTOM ENTRY

LOCATION

WATER LINESIDE ENTRYLOCATIONS

11/2"(38)

11/2"(38)

27"(686)

11/2"(38)

151/2"(394)

9"(229)

131/2"(343)

131/2"(343)

ANTI-TIPBRACKET

6"(152)

TOP VIEW TOP VIEW

SIDE VIEWFRONT VIEW

WATER LINESIDE ENTRYLOCATIONANTI-TIP

BRACKET

NOTE: ANTI-TIP BRACKET MUST BE INSTALLED TO PREVENT UNIT FROM TIPPING FORWARD

41/2"(114)

21/2" (64)

151/2" (394)

3/4"(19)

3"(76)

1/4"(6)

13" (330) 9"(229)

ANTI-TIPBRACKET

LOCATE WATER LINE(REAR ENTRY) WITHIN

SHADED AREA

LOCATE ELECTRICAL WITHINSHADED AREA – ORIENT GROUND

PRONG TO RIGHT AS SHOWN

*PLACEMENT OF THEANTI-TIP BRACKET

SHOULD BE 24" (610)FROM THE FRONT OF THE

UNIT WITHOUT PANELSTO THE BACK OF THE

ANTI-TIP BRACKET.

I N S T A L L A T I O NS P E C I F I C AT I O N SModels 700TR, 700TF(I) and 700TC(I)

Models without an ice maker will notrequire the water line connection.

O V E R A L L D I M E N S I O N SModels 700TR, 700TF(I) and 700TC(I)

A L L R E F R I G E R AT O RA L L F R E E Z E R

Model 700TRAll Refrigerator

Model 700TFAll Freezer

Model 700TFIAll Freezerwith Ice Maker

M O D E L 7 0 0 T RM O D E L 7 0 0 T F ( I )M O D E L 7 0 0 T C ( I )

Overall Dimensions

Width 27" (686)

Height 80" (2032)

Depth 24" (610)

Finished Opening

Width 27" (686)

Height 80" (2032)

Depth 25" (635)*

*The depth of the unitis 24" (610) from thefront of the unit to itsback. Your design maynecessitate moving theunit back or cabinetsforward to achieve aflush fit. This willrequire a minimumrough opening depthof 25" (635).

O V E R - A N D - U N D E RRefrigerator | Freezer

Model 700TC

Model 700TCIwith Ice Maker




38

DOOR MOUNTINGDETAIL

DRAWER MOUNTINGDETAIL

TOP OFROUGH

OPENING

7713/16"*(1976)

341/2"*(876)

3/8"(10)

131/4"(337)1/2"

(13)

101/4"(260)

203/8"(518)

14"(356)

15/16"(33)

93/4"(248)

4"(102)

80"*(2032)

36"(914)

24"(610)




105˚90˚

90˚ DOOR OPENING

DOOR/DRAWERCLOSED

MAXIMUM DOOR OPENING

DOOR/DRAWERCLOSED

191/2"*(495)341/2"*

(876)

24"(610)

347/8" (886)

7"*(178)

*DOOR/DRAWER PANEL THICKNESS NOT INCLUDED – DIMENSION WILL VARY WITH INSTALLATION

TOP VIEW

ANTI-TIPBRACKET*




ANTI-TIP BRACKET.

25" (635)

36"(914)

80" (2032)

27"(686)

25"(635)

WATER LINE BOTTOM ENTRY

LOCATION

WATER LINE SIDE ENTRY LOCATIONS

11/2"(38)

11/2"(38)

27" (686)

11/2"(38)

20" (508) 131/2"(343)

18" (457)

ANTI-TIP BRACKET

18" (457)

6"(152)

TOP VIEW TOP VIEW

SIDE VIEW FRONT VIEW

WATER LINE SIDE ENTRYLOCATION ANTI-TIP

BRACKET

21/2" (64)

20" (508)

3/4"(19)

3"(76)

171/2" (445) 131/2"(343)

ANTI-TIPBRACKET

NOTE: ANTI-TIP BRACKET MUST BE INSTALLED TO PREVENT UNIT FROM TIPPING FORWARD

41/2"(114)

1/4"(6)

LOCATE WATER LINE (REAR ENTRY) WITHIN

SHADED AREA

LOCATE ELECTRICAL WITHIN SHADED AREA – ORIENT GROUND


I N S T A L L AT I O NS P E C I F I C AT I O N SModels 736TR and 736TC(I)

Models without an ice makerwill not require the water lineconnection.

O V E R A L L D I M E N S I O N SModels 736TR and 736TC(I)

M O D E L 7 3 6 T RM O D E L 7 3 6 T C ( I )

Overall Dimensions

Width 36" (914)

Height 80" (2032)

Depth 24" (610)

Finished Opening

Width 36" (914)

Height 80" (2032)

Depth 25" (635)*

*The depth of the unitis 24" (610) from thefront of the unit to itsback. Your design maynecessitate moving theunit back or cabinetsforward to achieve aflush fit. This willrequire a minimumrough opening depthof 25" (635).


Model 736TRAll Refrigerator

O V E R - A N D - U N D E RRefrigerator | Freezer

Model 736TC

Model 736TCIwith Ice Maker


39

DRAWER MOUNTING DETAIL

341/2"*(876)

93/4"(248)

4"(102)FRONT VIEW SIDE VIEW

3/8"(10)

131/4"(337)1/2"

(13)

101/4"(260)

203/8"(518)

27"(686)

24"(610)



*DRAWER PANEL THICKNESS NOT INCLUDED

DRAWER CLOSED

191/2"*(495)

24"(610)

257/8" (657)

TOP VIEW

ANTI-TIPBRACKET*




ANTI-TIP BRACKET.

25"(635)

27"(686)

341/2"(876)

27"(686)

25"(635)

WATER LINE BOTTOM ENTRY

LOCATION

WATER LINE SIDE ENTRYLOCATIONS

11/2"(38)

11/2"(38)

27"(686)

11/2"(38)

151/2"(394)

9"(229)

131/2"(343)

131/2"(343)

ANTI-TIPBRACKET

6"(152)

TOP VIEW TOP VIEW

SIDE VIEW FRONT VIEW

WATER LINE SIDE ENTRYLOCATIONANTI-TIP

BRACKET NOTE: ANTI-TIP BRACKET MUST BE INSTALLED TO

PREVENT UNIT FROM TIPPING FORWARD

41/2"(114)

21/2" (64)

151/2" (394)

3/4"(19)

3"(76)

1/4"(6)

13" (330) 9"(229)

ANTI-TIPBRACKET

LOCATE WATER LINE (REAR ENTRY) WITHIN

SHADED AREA

LOCATE ELECTRICAL WITHIN SHADED AREA – ORIENT GROUND


I N S T A L L A T I O NS P E C I F I C AT I O N SModels 700BR, 700BF(I) and 700BC(I)

Models without an ice makerwill not require the water lineconnection.

O V E R A L L D I M E N S I O N SModels 700BR, 700BF(I) and 700BC(I)

D R A W E R S

Model 700BRAll Refrigerator

Model 700BFAll Freezer

Model 700BFIAll Freezerwith Ice Maker

Model 700BCRefrigerator | Freezer

Model 700BCIRefrigerator | Freezerwith Ice Maker

M O D E L 7 0 0 B RM O D E L 7 0 0 B F ( I )M O D E L 7 0 0 B C ( I )

Overall Dimensions

Width 27" (686)

Height 341/2" (876)

Depth 24" (610)

Finished Opening

Width 27" (686)

Height 341/2" (876)

Depth 25" (635)*

*The depth of the unitis 24" (610) from thefront of the unit to itsback. Your design maynecessitate moving theunit back or cabinetsforward to achieve aflush fit. This willrequire a minimumrough opening depth of25" (635).



40

C A B I N E T R Y A P P L I C A T I O N S

Integrated refrigeration is compatible with virtu-ally any style and look of cabinetry. The modelscan be used with framed as well as framelesscabinets. Because of the precise application andthe look you may want to achieve, there areimportant questions you need to answer beforeordering panels for the doors/drawers. As youlook at styles of cabinets, keep some importantfacts in mind:

IMPORTANT NOTE: The depth of each Inte-grated model is 24" (610) from the front of theunit to its back. You must allow for the thick-ness of the panel you are applying whenplanning for the finished rough opening depth ifyou want the front panel to be flush withsurrounding cabinetry. You must move the unitback into drywall or bring the cabinets forwardto achieve a flush fit.

The height of the door panel can grow beyond453/8" (1153) and exceed the 80" (2032) overallheight as long as you stay below the recom-mended door panel weight limit.

The toe kick clearance can vary with the heightof the lower drawer panel; the maximum panelheight is 1611/16" (424). You must keep aminimum space of 4" (102) clear below thebottom edge of the lower drawer panel so theunit can be properly vented.

We recommend using D-style handles. For thecabinet door, handles must be located near theedge of the panel opposite the hinge, centeredtop to bottom. Locate handles in the top centerarea of the drawer panels.

IMPORTANT NOTE: The inside edges of therough opening, as well as the sides and aportion of the backside of the decorative panelswill need to be finished, as they will be exposedwhen the doors are open.

F R A M E D C A B I N E T R Y

Framed cabinetry applications present you withdifferent questions to address. The illustrationsbelow show common applications of framedcabinetry. These are not meant to be the onlyalternatives, but are suggestions from designersaround the country. Also refer to the full-scaleillustrations at the end of this section forspecifics on door openings.

NOTE: In the illustrations below, the first widthdimension shown is for 27" (686) wide unitsand the second dimension is for 36" (914) wideunits.

Traditional frame – full overlay(top view)

SUB-ZEROUNIT

DOOR PANELCABINETDOOR

CABINETFRAME

TO WALL

24(610)

1/8" (10)REVEAL

36(914)

27(686)

OR

DOOR PANELCABINETDOOR

CABINETFRAME

SUB-ZEROUNIT TO WALL

24(610)

1/8" (10)REVEAL

36(914)

27(686)

OR

DOOR PANELCABINET DOOR

CABINETFRAME

SUB-ZEROUNIT TO WALL

24(610)

1/8" (10)REVEAL

36(914)

27(686)

OR

Traditional frame – standard overlay(top view)

Traditional frame – 3/8" (10) offset(top view)


Door and drawerpanels must be aminimum of 5/8" (16)thick.

The door panelcannot exceed 40 lbs(18 kg) and eachdrawer panel mustnot exceed 12 lbs(5 kg) for 27" (686)wide units. For 36"(914) wide units, thedoor panel weightlimit is 53 lbs (24 kg)and 16 lbs (7 kg) foreach drawer panel.

Dimensions are ininches with millime-ters in parenthesesunless otherwisespecified.


41

F R A M E D C A B I N E T R Y –B E A D E D I N S E T A P P L I C A T I O N

The illustration below shows a 27" (686) wideIntegrated base or tall unit installed within aframed cabinetry, beaded inset application.Review, giving particular attention to the overallpanel specifications. Also refer to the full-scaleillustrations at the end of this section forspecifics on door openings.

A) ALL REVEALS ARE 1/8" (3) B) DRAWER RAILS ARE ATTACHED TO DRAWER FRONTS C) BOTTOM RAIL MUST BE REMOVABLE *DIMENSIONS MAY VARY

CA

A

A

B

B

TOP VIEW

A A

DOOR PANEL

CABINET DOOR TO WALL SUB-ZERO

UNIT

PANEL WIDTH

11/2"(38)

11/2"(38)

477/8"(1216)


263/4" (679)

139/16"(345)

151/16"(383)

84"(2134)

11/2"(38)

11/2"(38)

4"*(102)

4" (102)

80"*(2032)

341/2"(876)*

24" (610)

27"(686)

SHADED AREAINDICATES STATIONARYSTYLES AND RAILS

27"(686)

24"(610)

2 7 " ( 6 8 6 )W I D E M O D E L S

Installation of a27" (686) wideIntegrated base ortall unit withinframed cabinetry.

*Dimensions may vary.

Dimensions are basedon a 1/8" (3) reveal. Areveal of up to 1/4" (6)is possible, but paneldimensions need to beadjusted accordingly.



42

F R A M E D C A B I N E T R Y –B E A D E D I N S E T A P P L I C A T I O N

The illustration below shows 36" (914) wideIntegrated tall unit installed within a framed cabi-netry, beaded inset application. Review, givingparticular attention to the overall panel specifica-tions. Also refer to the full-scale illustrations atthe end of this section for specifics on dooropenings.

3 6 " ( 9 1 4 )W I D E M O D E L S

Installation of a36" (914) wideIntegrated tall unitwithin framedcabinetry.



A) ALL REVEALS ARE 1/8" (3)B) DRAWER RAILS ARE ATTACHED TO DRAWER FRONTSC) BOTTOM RAIL MUST BE REMOVABLE

*DIMENSIONS MAY VARY

CA

A

A

B

B

TOP VIEW

A A

DOOR PANEL

CABINET DOORTO WALLSUB-ZERO

UNIT

PANEL WIDTH

11/2"(38)

11/2"(38)

477/8"(1216)


353/4" (908)

139/16"(345)

151/16"(383)

84"(2624)

11/2"(38)

11/2"(38)

4"*(102)

4" (102)

80"*(2032)

24"(610)

36"(914)

SHADED AREAINDICATES STATIONARYSTYLES AND RAILS

36"(914)

24"(610)

341/2"(876)*


43

F R A M E L E S S C A B I N E T R Y

The illustrations show hypotheti-cal installations of Integratedbase or tall units within framelesscabinetry. Review, giving particu-lar attention to the overall panelspecifications. Also refer to thefull-scale illustrations at the endof this section for specifics ondoor openings.

A

A

A

A) ALL REVEALS ARE 1/8" (3) *DIMENSIONS MAY VARY

SIDE VIEW

24"(610)

PANEL WIDTH

453/8"(1153)

263/4"* (679)

139/16"(345)

1611/16"*(424)

4"*(102)

80"*(2032)

341/2"(876)*

27"(686)

FINISHED OPENINGTOE KICK

797/8"*(2029)

A

A

A

A) ALL REVEALS ARE 1/8" (3) *DIMENSIONS MAY VARY

SIDE VIEW

24"(610)

PANEL WIDTH

453/8"(1153)

353/4"* (908)

139/16"(345)

1611/16"*(424)

4"*(102)

80"*(2032)

341/2"(876)*

36"(914)

FINISHED OPENINGTOE KICK

797/8"*(2029)

3 6 " ( 9 1 4 )W I D E M O D E L S

Installation of a36" (914) wideIntegrated tall unitwithin framelesscabinetry.



2 7 " ( 6 8 6 )W I D E M O D E L S

Installation of a27" (686) wideIntegrated base ortall unit withinframeless cabinetry.



To install integratedpanels, see thedetailed proceduresoutlined in theSub-Zero IntegratedInstallationInstructions.



44

P A N E L C O N S I D E R A T I O N S

The illustrations below provide panel widthdimensions for installation of a single tall unit,27" (686) and 36" (914) wide models.

Illustrations on the following page provide panelwidth dimensions for installing two tall unitsside by side, 27" (686) wide models and 36"(914) wide models.

2634 (679)

34 (19) PANEL

APPLIANCEDOOR WIDTH

SUB-ZEROUNIT

TO BACKOF UNIT

2578 (657)

27(686)

24(610)

CABINETRYOR SIDEPANEL

25(635)


25(635)

18 (3)

REVEALmin*1

8 (3)

REVEALmin*

*SUBTRACT PANEL WIDTH FROM CABINETRY OPENING TO DETERMINE ACTUAL WIDTH OF REVEAL

3534 (908)

34 (19) PANEL

APPLIANCEDOOR WIDTH

SUB-ZEROUNIT

TO BACKOF UNIT

3478 (886)

36(914)

24(610)


25(635)


25(635)

18 (3)

REVEALmin*1

8 (3)

REVEALmin*


IMPORTANT NOTE: The depth of eachIntegrated model is 24" (610) from the front ofthe unit to its back. You must allow for thethickness of the panel you are applying whenplanning for the finished rough opening depth ifyou want the front panel to be flush withsurrounding cabinetry. You may have to movethe unit back into drywall or bring the cabinetsforward to achieve a flush fit.

3 6 " ( 9 1 4 )W I D E M O D E L S

Panel width dimen-sions for installationof a 36" (914) widetall unit.


2 7 " ( 6 8 6 )W I D E M O D E L S

Panel width dimen-sions for installationof a 27" (686) widetall unit.






45

As the reveal between cabinets and the

Integrated unit decreases, the potential

exists for severe finger pinching or crushing

if a hand or fingers are placed in the

opening when the door is closing.

When 3/4" (19) or thicker panels are used

and a reveal less than 1/4" (6) is maintained,

the door panels may cause damage to the

Sub-Zero unit when the door is open at the

maximum 105˚ stop. You should use the

built-in 90˚ stop to prevent damage.

261316 (681) 2613

16 (681)

34 (19) PANEL 3

4 (19) PANEL

DOOR

SUB-ZEROUNIT

DOOR

SUB-ZEROUNIT

54 (1372)

TO BACKOF UNIT

24(610)

18 (3)

REVEALmin*1

8 (3)

REVEALmin*

18 (3)

REVEALmin*



25(635)


25(635)

34 (19) PANEL 3

4 (19) PANEL

DOOR

SUB-ZEROUNIT

DOOR

SUB-ZEROUNIT

72 (1829)

TO BACKOF UNIT

24(610)

18 (3)

REVEALmin*1

8 (3)

REVEALmin*

18 (3)

REVEALmin*



25(635)


25(635)

351316 (910) 3513

16 (910)

3 6 " ( 9 1 4 )W I D E M O D E L S

Panel width dimen-sions for installationof two 36" (914)wide tall units sideby side.


2 7 " ( 6 8 6 )W I D E M O D E L S

Panel width dimen-sions for installationof two 27" (686)wide tall units sideby side.


To install integratedpanels, see thedetailed proceduresoutlined in theSub-Zero IntegratedInstallationInstructions.

P A N E L C O N S I D E R A T I O N S



46

I N S T A L L A T I O N O P T I O N S

The illustrations show some typical installationsand their dimension considerations. The depthdimension in the illustrations may vary depend-ing on cabinet styles, treatment of countertopsor other design options.

IMPORTANT NOTE: The depth of eachIntegrated model is 24" (610) from the front ofthe unit to its back. Your design may necessitatemoving the unit back or cabinets forward toachieve a flush fit. This will require a minimumrough opening depth of 25" (635). Refer to theillustrations.

NOTE: In the Installation Options illustrations,the first width dimension shown is for 27" (686)wide units and the second dimension is for 36"(914) wide units.

D U A L I N S T A L L A T I O N S

If two or more Integrated models are installedside by side where there is 2" (51) or less ofspace between the units, a heater kit is recom-mended—TTDUAL for two tall units installed sideby side and BBDUAL for two base units or abase unit and a tall unit installed side by side.These optional components are available throughyour Sub-Zero dealer.

TOP VIEW

CABINETS

25(635)

36(914)

27(686)

OR

Installation without side panels

Installation with side panels

Installation of two units side by side

Installation at end of run

MINIMUM (16) SIDE PANELS58

CABINETS

25(635)

36(914)

27(686)

OR

TOP VIEW

CABINETS

72(1829)))

54(1372)))

25(635)

OR

MINIMUM (16) SIDE PANELS58

CABINETS

25(635)

36(914)

27(686)

OR




47

D O O R P A N E L H E I G H T

The height of the door panel can grow beyond453/8" (1153) and exceed the 80" (2032) overallheight, as long as you stay below the recom-mended door panel weight limit.

The top illustration shows how the panel maygrow and what you need to consider doing tofinish the area in back of the door panel.

IMPORTANT NOTE: The valance you use tofinish the area behind the door panel must staybehind the front plane of the finished molding.

4538

(1153)

TOBOTTOM

OFDOORPANEL

TOFLOOR

18

(3)

112 (38)

TO WALL

DECORATIVE VALANCE

DECORATIVE VALANCECANNOT EXTEND BEYONDTHE FRONT OF THIS PLANE

REMOVABLE MOLDINGBY SUB-ZERO

TOP HINGE

25(635)

*FINISHED HEIGHT OF 80" (2032) IS TO TOP OF SUB-ZERO MOLDING

80*(2032)

10 916

(268)

161116

(424)

PANEL

PANEL

10(254)

4(102)

OPTIONAL

258

(67) 4

(102) TO

91116

(246)

12

(13)

FLOOR

TO WALL25

(635)

BASE MOLDING MUST BE REMOVABLE

T O E K I C K C L E A R A N C E

The toe kick clearance can vary with the heightof the lower drawer panel; the maximum panelheight is 1611/16" (424).

IMPORTANT NOTE: You must keep a minimumspace of 4" (102) clear below the bottom edgeof the lower drawer panel so the unit can beproperly vented. In addition, any decorative basemolding must be removable for possible servic-ing and cleaning of the condenser.

The bottom illustration shows the area belowthe lower drawer where the operating mechani-cal equipment of the Integrated unit is housed.

K I C K P L A T E A R E ABase and Tall Models

U P P E R V A L A N C ETall Models

The depth of eachIntegrated model is24" (610) from thefront of the unit to itsback. Your designmay necessitatemoving the unit backor cabinets forward toachieve a flush fit.This will require aminimum roughopening depth of 25"(635).





48

18

34

MIN.(3)

PANEL

SIDE MOLDING ANDINSTALLATION HARDWAREPROVIDED BY SUB-ZERO

LINE OF INTERFERENCE*AT MAXIMUM DOOR OPENING

MOUNTING BRACKET SCREW

(19)

FLUSHFURNITUREFINISH

LINE OF INTERFERENCE*

TO BACKOF UNIT

24(610)

SUB-ZERO DOOR

2578 (657) DOOR WIDTH FOR 27" (686) MODELS


REVEAL

IMPORTANT NOTE: The depth of eachIntegrated model is 24" (610) from thefront of the unit to its back. Yourdesign may necessitate moving theunit back or cabinets forward toachieve a flush fit.

F R A M E D C A B I N E T R Y

D O O R C L O S E D

Full-scale (top view)

24(610)


SUB-ZERO DOOR

TO BACKOF UNIT

1 0 5 ˚ M A X I M U MD O O R O P E N I N G

1/4 scale (top view)

*If the panel is thicker than 3/4" (19), it isrecommended that you utilize the built-in90˚ door stop to prevent damage to thepanel and face frame.


49

18 MIN.(3)

REVEAL

34 PANEL

LINE OF INTERFERENCE*AT MAXIMUM DOOR OPENING

MOUNTING BRACKET SCREW

(19)

TO BACKOF UNIT

24(610)

SIDE MOLDING ANDINSTALLATION HARDWAREPROVIDED BY SUB-ZERO


SUB-ZERO DOOR



IMPORTANT NOTE: The depth of eachIntegrated model is 24" (610) from thefront of the unit to its back. Yourdesign may necessitate moving theunit back or cabinets forward toachieve a flush fit.

F R A M E L E S S C A B I N E T R Y

D O O R C L O S E D

Full-scale (top view)

TO WALL

24(610)


SUB-ZERO DOOR

3/4" (19) DOOR PANEL

SIDE PANEL COUNTERTOP

1 0 5 ˚ M A X I M U MD O O R O P E N I N G

1/4 scale (top view)

Adjacent side panel and

countertop application.

*If the panel is thicker than 3/4" (19), it isrecommended that you utilize the built-in90˚ door stop to prevent damage to thepanel and face frame.



W I N E S T O R A G E

50

U N D E R C O U N T E R W I N E S T O R A G E

Sub-Zero‘s innovative addition to its completeline of residential refrigeration is wine storageequipment—the ultimate in beauty, engineering,and attention to detail. From the exterior and thesmooth lines of the free-standing Model 424FSclassic stainless steel to the ability to use woodon the Built-In and Integrated models, each unitis beautiful.

With the exception of the free-standing Model424FS, each model is available in three stainlesssteel finishes and will have the capability ofhaving wood panels applied to the doors. Withthe Model 427R, you can also apply the wood tothe drawers.

The new Model 315W, a single-zone WineStorage unit, comes only with a glass door andcan be ordered as an overlay or classic stainlesssteel unit.

The free-standing Model 424FS does not requireany panels or surrounding cabinetry; it comeswith classic stainless steel exterior.

All models will be shipped with glass doors asstandard equipment. The glass doors allow oneto see the wine that is being stored. Optionalsolid doors and high altitude glass doors will betreated as special orders and must be ordered 90days before you expect delivery. Model 315Wcannot be ordered with a solid door.

Stainless steel models will be shipped withtubular stainless steel handles, while the overlaymodels will come with no handle hardware.Optional stainless steel panels and handles forModels 427 and 427R are offered in the classic,platinum and carbon stainless steel finishes andare ordered and shipped as sales accessories.The stainless steel Models 424 and 430 must beordered in one of three stainless steel finishes ofclassic, platinum and carbon.

Optional handles are available for all modelsexcept the framed and stainless steel Model430. The framed Model 430 will come with anextruded handle identical in design to our Built-Inmodels.

Standard grille assemblies for the Model 430 willbe provided in 1" (25) increments from 10" (254)to 15" (381). The standard height will be 11"(279). The framed model will have a louveredgrille, the stainless steel model will feature aheavy-duty grille, and the overlay model willhave the panel grille, which accepts decorativepanel inserts.

For information regarding specific Wine Storagemodels, refer to the illustrations in this section.

The illustrations represent the full line ofWine Storage models. The Model 424FSfree-standing unit comes with a classicstainless steel exterior.


27"(686)

80"(2032)

27"(686)

80"(2032)

30"(762)

84"(2134)

241/4"(616)

343/16"(868)

341/16"(865)

151/8"(384)

34"(864)

237/8"(606)

With the installation of a harness kit,Wine Storage models, except Model 315W,are Star-K compliant to meet strict religiousregulations in conjunction with specificinstructions found on www.star-k.org.For details about the harness kit, contactyour Sub-Zero dealer.

A L L W I N E S T O R A G E

W I N E S T O R A G E | R E F R I G E R AT O R

M O D E L 4 2 7 R

Integrated

M O D E L 4 2 7

Integrated

M O D E L 4 3 0

Built-In

M O D E L 3 1 5 W

Built-In

M O D E L 4 2 4

Built-In

M O D E L 4 2 4 F S

Free-Standing

Model 430 has been redesigned asModel WS-30. For more information,visit our website, subzero.com.


51

F E A T U R E S A N D O P T I O N S

When looking for wine storage, you no longerhave to think only about an undercounter appli-cation. Sub-Zero offers you complete flexibilityfrom the perspective of design applications andstorage capabilities.

Model 315W, a single-zone Wine Storage unit,comes as an overlay or classic stainless steelunit and is offered only with a glass door.

Model 424 comes in the overlay and stainlesssteel door panel configurations. Model 424FS(free-standing) is identical to the Model 424 butwith classic stainless steel exterior and isdesigned to be attractive in a stand-alonesetting. Models 424 and 424FS are available ineither a glass or solid door model.

Models 427 and 427R are offered as integratedor stainless steel and are available in either aglass or solid door model. Optional stainlesssteel panels and handles are offered in classic,platinum and carbon stainless steel finishes atthe 80" (2032) height, and only classic stainlesssteel at the 84" (2134) height. Stainless steelpanels are available as sales accessories.

Model 430 comes in the framed, overlay andstainless steel options and is available in either aglass or solid door model. Stainless steel Model430 must be ordered in one of the stainless steelfinishes of classic, platinum and carbon.

Built-In Look. Sub-Zero offers you a host ofdesign alternatives to choose from when select-ing the look you want. Wood or stainless steel,framed, overlay or integrated.

Dual Zone System*. With the exception of thesingle-zone Model 315W, all Wine Storagemodels allow you to have precise temperaturecontrol within one degree of your pre-settemperature in each of the two wine compart-ments.

Dual Refrigeration System*. In a similar fashionto our Built-In, each Wine Storage model hasdual refrigeration so your client will havespecific, individual temperature control of thetwo wine compartments.

Electronic Controls*. Microprocessor offerstouch pad controls that are easy to understandand that set the temperatures accurately.

Display Shelf*. This beautiful shelf offers yourclients the opportunity to display those prizebottles or magnums of wine in their collection. Itis illuminated with discreet lighting mounted inthe control panel. (Not available with Models315W, 424 and 424FS.)

Storage Shelves. The sturdy, rustproof wireshelves can easily accommodate standard 750ml bottles, half bottles, as well as magnums. Allthe shelves are finished off with a natural cherrywood facing. In addition, all shelves will enableyou to be sure the wine is stored properly andthat the corks are in contact with the bottles‘contents.

Roller Assembly. All shelves have a rollerassembly, which enables you to have a three-quarter extension for easy access to all bottlesof stored wine.

Service Alert*. An indicator light will let youknow if service may be necessary.

Home Alarm*. Wiring connections give you theoption of hooking the Wine Storage unit up toyour home security system.

Discreet Lighting. Our soft low-wattage lightingis independent of door opening.

Correct Temperature*. The range of eachtemperature zone is 38˚F (3˚C) to 65˚F (18˚C), andyour set temperature is digitally displayed in thecontrol panel.

Humidity. Proper humidity is maintainedthroughout the entire unit.

UV Protection. The tinted glass minimizes theamount of ultraviolet light entering the unit.

Lock*. A lock will be offered as an option for allWine Storage models. The lock is offered as asales accessory and should be ordered throughyour Sub-Zero dealer. Special planning is neces-sary when ordering locks for Models 427 and427R, refer to page 61 for details.

Solid Door*. If you would like to order a modelwithout glass, you have that option. This will betreated as a special order and must be ordered90 days before you expect delivery.

High Altitude Glass. For installations above5,000' (1524 m) in elevation, we offer the highaltitude glass as a special order. The highaltitude glass door is standard on Model 315W.

Tight Seal. Magnetic gaskets around the doorsgive extra-tight seals.

Kickplate. The solid, adjustable kickplate gives atrue built-in look and conforms to AmericanInstitute of Architects standards.

Front Venting. All Sub-Zero Wine Storagemodels are designed for mechanical systemairflow at the front of the appliance. Decorativepanels must not cover louvered surfaces orprevent removal of louvered components.



*Not available with Model 315W.


52

M O D E L 4 2 4 F SM O D E L 4 2 4

M O D E L 3 1 5 W

U N D E R C O U N T E RB U I L T - I N


Overlay Design 315W/O

Classic Stainless Steel 315W/S


Overall Width 151/8" (384)



Wine Storage Capacity 26 bottles*






F E A T U R E S

1 Temperature Zone

4 (750 ml) Bottles per Standard Shelf

6 Standard Shelves (24 bottles*)

1 Fixed Bottle Holder (2 bottles*)

Full-View High Altitude Glass Door

M O D E L 3 1 5 W

M O D E L 4 2 4

U N D E R C O U N T E RB U I LT - I N






Full-View Glass Door (standard)

High Altitude Glass Door**

Solid Door









Shipping Wt (glass) 190 lbs (86 kg)

Shipping Wt(glass/S/P/B) 195 lbs (88 kg)

Shipping Wt (solid) 185 lbs (84 kg)

F E A T U R E S

2 Temperature Zones


2 Top Zone Shelves (16 bottles*)

3 Bottom Zone Shelves (24 bottles*)


Full-View Glass Door

M O D E L 4 2 4 F S

U N D E R C O U N T E RF R E E - S T A N D I N G




Solid Door








Shipping Wt 220 lbs (100 kg)

F E A T U R E S

2 Temperature Zones






Classic Stainless Steel Exteriorand Door Frame

*750 ml bottles.

**High altitude glass doors are forinstallations at or above 5,000' (1524 m) inelevation and will be treated as a specialorder. Please allow 90 days for delivery.When ordering, add an (HA) before the (G) toobtain the correct model number.

***Optional stainless steel panels andhandles are ordered and shipped as salesaccessories. For additional information onpanel and handle sizes and applications,check our website, subzero.com.


Classic stainless steel frontpanels—platinum and carbonavailable in certain sizes(Models 427 and 427R)*

Tubular handles in classic,platinum and carbon stainlesssteel

Front, side and grille panels(framed Model 430)*

Louvered, panel or stainlesssteel grilles in varied heights(Model 430)*

UL-approved door lock kit

Dual installation heater kit(Models 427 and 427R)*

*Accessory is available only formodels listed.


53

M O D E L 4 2 7 R

W I N E S T O R A G E | R E F R I G E R AT O R




Solid Door













F E AT U R E S

3 Temperature Zones

2 Refrigerated Drawers




1 Display Shelf (6 bottles*)



Integrated

Classic, platinum or carbon stainlesssteel finish (includes handles)***

M O D E L 4 3 0



Framed Design 430/F







Solid Door










Shipping Wt(glass/S/P/B) 445 lbs (202 kg)


F E AT U R E S

2 Temperature Zones






M O D E L 4 2 7





Solid Door











F E A T U R E S

2 Temperature Zones







Integrated

Classic, platinum or carbon stainlesssteel finish (includes handle)***

M O D E L 4 3 0 M O D E L 4 2 7 RM O D E L 4 2 7

NOTE: For Wine Storage standard glass doormodels, add (G) to the model number and forsolid door models, add (S) to the modelnumber (example 424G or 424S). The excep-tion is Model 315W which is available as aglass door model only.

Model 430 has been redesigned asModel WS-30. For more information,visit our website, subzero.com.



54


Review the Overall Dimensions and InstallationSpecifications illustrations for your Wine Storagemodel on the following pages. These specifica-tions cover all the details you need to knowabout space allocation and placement of electri-cal, whether the models are framed, overlay,stainless steel or integrated.

All Wine Storage models must be installed sothat the door can open a minimum of 90˚ or youwill have problems pulling the wine shelves out.Refer to the door clearance and door swinginformation.

For corner installations, you need allow for aminimum 3" (76) filler so the door can open to90˚. If you are using larger handle hardware, youwill also need to take that into account.

For a maximum 90˚ door opening, use the doorstop built into the hinge system of Model 427.An optional 90˚ door stop kit for Model 430 isavailable from your Sub-Zero dealer.

If you will be connecting the unit to a homesecurity system, you must allow a minimum of36" (914) of the system‘s wiring to be routed inthe electrical area designated for your model.

IMPORTANT NOTE: The anti-tip bracket must beinstalled to prevent the unit from tippingforward.

D U A L I N S T A L L A T I O N S

If you are installing a Wine Storage unit next toan existing Sub-Zero unit, you may have to allowfor a filler strip.

If you are installing a Model 427 or 427R WineStorage unit next to an existing IntegratedSub-Zero unit, with 2" (51) or less between theunits, an optional heater kit (BBDUAL orTTDUAL) will need to be installed to preventmoisture from forming between the units. Thisoptional kit is available through your Sub-Zerodealer.


A 115 V AC, 60 Hz, 15 amp circuit breaker andelectrical supply are required. A separate circuitservicing only this appliance is required.

All Sub-Zero Wine Storage models are equippedwith a power supply cord with a 3-prong ground-ing plug, which must be plugged into a mating3-prong grounding-type wall receptacle. Followthe National Electrical Code and local codes andordinances when installing the receptacle. Referto the Installation Specifications illustrations onthe following pages for electrical placement foryour model.





55

I N S T A L L A T I O N S P E C I F I C A T I O N SUndercounter Models

Model 315W


B) Rough Opening Height 341/2" (876)

C) Min Door Clearance 165/8" (422)

D) Min Clearance at 90˚ 171/4" (438)

Model 424

A) Rough Opening Width 24" (610)

B) Rough Opening Height 341/2" (876)


D) Min Clearance at 90˚ 26" (660)

Model 424FS*


D) Min Clearance at 90˚ 26" (660)

*Free-standing Model 424FS requires nosurrounding cabinetry.



90˚

D

C

AROUGH OPENING

WIDTH

151/2"(394)

MODELS 424 | 424FSLOCATE ELECTRICALWITHIN SHADED AREA

MODEL 315WLOCATE ELECTRICAL

ANYWHERE ONBACK WALL

E

41/2"(114)

21/2"(64)

BROUGH

OPENINGHEIGHT TOFINISHED

FLOORING

24"(610)

ROUGHOPENING

DEPTH

TOP VIEW

FRONT VIEW


(CABINET DIMENSION)

TOE KICK

24 14

(616)

4(102)

(625) 5824

*34 316

(868)


O V E R A L L D I M E N S I O N SUndercounter Wine Storage

U N D E R C O U N T E R

Model 315WBuilt-In

Model 424Built-In

Model 424FSFree-Standing

M O D E L 3 1 5 WBuilt-In

Width 151/8" (384)

Height 341/16" (865)

Depth 24" (610)

M O D E L 4 2 4Built-In

Width 237/8" (606)

Height 34" (864)

Depth 24" (610)

Note the location of pre-drilledholes for optional handle hardware.

M O D E L 4 2 4 F SFree-Standing

Width 241/4" (616)

Height 343/16" (868)

Depth 245/8" (625)


(CABINET DIMENSION)

4(102)

34

(273)10

CENTEREDVERTICALLY

DOOR FRAME(597)1223

30(767)

DOORFRAME

*34(864)

(587)1823

316

23 78

(606)


151/8"(384)

341/16"(865)

301/16"(764)

4" (102)

FRONT VIEW




56

I N T E G R A T E D

Model 427All Wine Storage

Model 427RWine Storage |Refrigerator

O V E R A L LD I M E N S I O N SModel 427 | 427R

Width 27" (686)

Height 80" (2032)

Depth 24" (610)

Note the location ofpre-drilled holes foroptional handlehardware.

I N S T A L L AT I O N S P E C I F I C AT I O N SModels 427 | 427R



IMPORTANT NOTE: The depth of Models427 and 427R is 24" (610) from the front ofthe unit to its back. Your design may neces-sitate moving the unit back or cabinetsforward to achieve a flush fit. This willrequire a minimum rough opening depth of25" (635).

27"(686)

ROUGH OPENING WIDTH

25"(635)

ROUGHOPENING

DEPTH

151/2"(394)


E

41/2"(114)

21/2"(64)

ANTI-TIP BRACKET

FRONT VIEW

TOP VIEW

80" (2032)ROUGH OPENING

HEIGHTTO FINISHEDFLOORING

791/2" (2019)MIN HEIGHTREQUIRED

O V E R A L L D I M E N S I O N SAll Wine Storage – Model 427

14


(356)

(UNIT DIMENSION)

1316(20)

*7858

(1997)

81516

(227)

4(102)

27(686)

24(610)

34

(273)10

CENTEREDVERTICALLY

DOOR FRAME (664)1826

70 716

(1789)

DOORFRAMEWITH

HINGES

80(2032)


Wine Storage | Refrigerator – Model 427R

14

DRAWER FRONT


(356)

2038

(517)

12

(13)

1014

(260)

1314

(337)

38

(9)

(UNIT DIMENSION)

1316 (20)

*78 58(1997)

9 34

(248)

4(102)

27(686)

24(610)

34

(273) 10

CENTERED VERTICALLY

(650) 9

1625

DOOR FRAME (664) 1826

*3412

(877)

4478

(1139)

DOORFRAMEWITH

HINGES

80(2032)


237/8"(606)

90˚105˚

MAXIMUMDOOR SWING

35" (889)DOOR CLEARANCE


251/2"(648)

251/2"(648)


57

O V E R A L LD I M E N S I O N SModel 430

Width 30" (762)

Height 84" (2134)

Depth 24" (610)

Note the location ofpre-drilled holes foroptional handlehardware.

I N S T A L L A T I O N S P E C I F I C A T I O N SAll Wine Storage – Model 430



751/2"(1918)

7"(178)

6"(152)

291/2"(749)

ROUGH OPENING WIDTH

24"(610)

ROUGHOPENING

DEPTH

E


ANTI-TIP BLOCK

FRONT VIEW

TOP VIEW


HEIGHTTO FINISHED


11" (279) GRILLE

83" (2108)MIN HEIGHTREQUIRED

(LEVELERS IN)

O V E R A L L D I M E N S I O N SAll Wine Storage – Model 430

* INCH (13) ADJUSTMENT IN LEVELING LEGS12


84(2134)

418

(105)

34

(273)10

CE

NT

ER

ED

VE

RT

ICA

LLY

DOOR FRAME(719)5

1628

6778

(1724)

(606)7823

DOORFRAME

TOEKICK

30(762)

A L L W I N ES T O R A G E

Model 430Built-In

90˚130˚

MAXIMUMDOOR SWING



301/8"(765)

301/8"(765)

237/8"(606)

BEHINDFRAME




58

D O O R P A N E L S

Unless you are installing a stainless steel model,you will need to provide a complete door panelin the instance of a solid door model, or a framefor the glass door application where wine will beseen from the outside. If you order a stainlesssteel unit, Models 315W, 424, 424FS and 430will be shipped with their panels and hardwareinstalled and you will merely install the Sub-Zero.However, for Models 427 and 427R, you willhave to have the stainless steel panels andhandles installed.

Wine Storage solid door models are available asa special order. You must allow 90 days from thetime of order until you can expect delivery.

M O D E L 4 2 4 F S – F R E E - S T A N D I N G

The free-standing Model 424FS does not requireany panels or surrounding cabinetry. It has abeautiful classic stainless steel exterior, doorframe and handle. Refer to the Overall Dimen-sions illustration for the Model 424FS.

15"(381)

151/8" (384)OVERALL

WIDTH

223/8" (568)

341/16"(865)

OVERALLHEIGHT

301/16"(764)

4" (102)

19" (483)

SIDE VIEWFRONT VIEW

TOEKICK

O V E R L A Y P A N E L S P E C I F I C AT I O N SModel 315W

Door Panel Width 15" (381)

Door Panel Height 301/16" (764)

Min Width of Rails and Stiles 21/4" (57)

Door Frame Panel Weight Limit 10 lbs (5 kg)

Min Panel Thickness 5/8" (16)

C A B I N E T R Y D I M E N S I O N SModel 315W




59

O V E R L A Y P A N E L S –M O D E L S 3 1 5 W | 4 2 4

The overlay panel applied to Models 315W and424 should not be confused with the Built-Inoverlay panel application. The overlay panel willconsist of only a frame and would be either the5/8" (16) or 3/4" (19) thick panel you may beusing. It is affixed directly to the door itself withscrews through a series of pre-drilled holes inthe perimeter of the door itself. You do not needany backer or spacer panel.

Refer to the Overall Dimensions and CabinetryDimensions illustrations for Models 315W and424 to give you a better idea of the exact spaceour unit needs and how the panel fits in relation-ship with the unit.

The glass door opening of the standard Model315W and 424 are designed to be exposed toroom air circulation. Decorative overlays on theglass should be kept to a minimum. Also, railsand stiles can be increased in size but shouldnot exceed cabinet manufacturers‘ standardwidth. They cannot exceed overall door paneldimensions specified, as they would interferewith the operation of the door. The back sides ofrails and stiles that will be visible through theglass door will need to be finished. Also, theinside edges of the frames must be finished tomatch the front surface.

The Overall Dimensions illustrations show thelocation of predrilled holes for optional handlehardware. Refer to page 64 for specifics aboutinstalling handles on this overlay application.

IMPORTANT NOTE: Wine Storage models with asolid door are available as a special order andrequire 90 days for delivery. When orderingpanels for a solid door unit, follow the overallpanel dimensions listed; rail and stile dimensionsdo not apply. Model 315W is not available with asolid door.

IMPORTANT NOTE: When planning to install theModel 315W or 424 next to adjoining cabinetry,you must make provisions to allow the door toopen to a maximum of 145˚ and not interferewith the door panel. Refer to the full-scale illus-tration at the end of this section.

A solid panel must not be installed on a

glass door unit, as this may cause moisture

to form behind the panel.

* INCH (13) ADJUSTMENT IN LEVELING LEGS

** MODEL 424/S (STAINLESS STEEL WRAPPED DOOR) FINISHES OFF AT 23 INCHES DEEP

12


(CABINET DIMENSION)DOOR PANEL(603)

3423

30(764)

DOORPANEL

CENTEREDVERTICALLY

*3412

(877)

(606)78**23

116

TOEKICK

23 78

(606)

4(102)

78

O V E R L A Y P A N E L S P E C I F I C AT I O N SModel 424

Door Panel Width 233/4" (603)




Solid Door Panel Weight Limit 20 lbs (9 kg)


C A B I N E T R Y D I M E N S I O N SModel 424

I N S T A L L AT I O N

To install overlaypanels, see thedetailed proceduresoutlined in theSub-Zero WineStorage InstallationInstructions.



60

IMPORTANT NOTE: The glass door opening ofthe standard Models 427 and 427R is designedto be exposed to room air circulation. Decorativeoverlays on the glass should be kept to aminimum. While the cabinet front stiles are aminimum of 21/4" (57) for both Models 427 and427R, the top and bottom rails are different.

Rails and stiles can be increased in size butshould not exceed cabinet manufacturers‘standard width. They cannot exceed overall doorpanel dimensions specified, as they would inter-fere with the operation of the door. The backsides of rails and stiles that will be visiblethrough the glass door will need to be finished.Also, the inside edges of the frames must befinished to match the front surface.

IMPORTANT NOTE: The inside edges of therough opening will need to be finished as theywill be exposed when the doors are open.



(UNIT DIMENSION)

80(2032)

27(686)

24(610)

DOOR PANEL(679)3426

79 78

(2029)

TRIMMEDDOOR

FINISHED OPENING

7578

(1927)

4(102)

TOE KICK

4(102)

TOE KICK

FINISHEDOPENING

DOORPANEL

I N T E G R AT E D P A N E L S P E C I F I C AT I O N SModel 427



Min Width of Top Rail 33/4" (95)

Min Width of Bottom Rail 8" (203)

Min Width of Stiles 21/4" (57)





I N T E G R A T E D P A N E L S –M O D E L S 4 2 7 | 4 2 7 R

The integrated full panels or frame panels forglass doors for these models will follow some ofthe identical planning processes used with theIntegrated line. The installation of the doorpanels is completely different, however. Ratherthan using the mounting hardware we used withthe Integrated line, door panels for both Models427 and 427R will be applied with screwsapplied through our door.

The drawer panels for the Model 427R will beapplied using the Integrated technique ofmounting brackets.

Refer to the Overall Dimensions and CabinetryDimensions illustrations for Models 427 and427R to give you a better idea of the exact spaceour unit needs and how the panel fits in relation-ship with the unit.

IMPORTANT NOTE: The depth of Models 427and 427R is 24" (610) from the front of the unitto its back. You must allow for the thickness ofthe panel you are applying when planning for thefinished rough opening depth if you want thefront panel to be flush with surrounding cabi-netry. You may have to move the unit back intothe drywall or bring the cabinets forward. Referto the Integrated Refrigeration section.




61

I N T E G R A T E D P A N E L S –M O D E L S 4 2 7 | 4 2 7 R

IMPORTANT NOTE: The dimensions of thesepanels and stiles are assuming the models finishoff at 80" (2032) in height overall and have a 4"(102) toe kick for the Model 427. If you finish offat 84" (2134), for instance, you must add 4"(102) additional to the overall height of the paneland remember to add 4" (102) to the top rail.Likewise, if you allow for a 6" (152) toe kick forthe Model 427, you must subtract 2" (51) fromthe bottom rail.

Door panels for Models 427 and 427R can growbeyond the 80" (2032) height to accommodateany size door as long as you stay below doorpanel weight limit of 20 lbs (9 kg) for glass doorunits and 40 lbs (18 kg) for solid door units.Refer to the specifications under Door PanelHeight on page 47 of the Integrated section.

IMPORTANT NOTE: The toe kick area on theModel 427 cannot be larger than 6" (152), andno larger than 9" (229) for the 427R. The toekick area for either model cannot be less than4" (102).

In the Overall Dimensions illustrations, note thelocation of pre-drilled holes for optional handlehardware. Refer to page 64 for specifics aboutinstalling handle hardware on this overlayapplication.

IMPORTANT NOTE: If you are installingSub-Zero‘s optional lock kit on a Model 427 or427R, you may have to order door panels thatexceed the 80" (2032) finished height. Consultthe lock kit installation instructions and see ifyour panels will allow for an adequate installa-tion. To obtain these instructions, check ourwebsite, subzero.com.

IMPORTANT NOTE: In the panel specificationsfor Model 427R, the bottom drawer panel heightis based on a 4" (102) toe kick. If you want toshow a 6" (152) toe kick, you must subtract 2"(51) from the bottom drawer panel height.

IMPORTANT NOTE: Wine Storage models with asolid door are available as a special order andrequire 90 days for delivery. When orderingpanels for a solid door unit, follow the overallpanel dimensions indicated in the chart; rail andstile dimensions do not apply.





DRAWER PANEL


18(3)

161116

(424)

13 916

(345)

18

(3)

(UNIT DIMENSION)

*3412

(877)

80(2032)

27(686)

24(610)

(679)3426

DOOR PANEL(679)3426

79 78

(2029)

FINISHED OPENING

4538

(1153)

4(102)

TOE KICK

4(102)

TOE KICK

FINISHEDOPENING

TRIMMEDDOOR

C A B I N E T R Y D I M E N S I O N SModel 427R

I N T E G R AT E D P A N E L S P E C I F I C A T I O N SModel 427R



Min Width of Top Rail 33/4" (95)

Min Width of Bottom Rail 3" (76)

Min Width of Stiles 21/4" (57)



Top Drawer Panel Width 263/4" (679)

Top Drawer Panel Height 139/16" (345)

Bottom Drawer Panel Width 263/4" (679)

Bottom Drawer Panel Height 1611/16" (424)

Drawer Panel Weight Limit 12 lbs (5 kg) each



To install integratedpanels, see thedetailed proceduresoutlined in theSub-Zero WineStorage InstallationInstructions.


62

M O D E L 4 3 0 – O V E R L A Y P A N E L S

Your overlay model will be shipped withouthandle hardware and with an 11" (279) overlaypanel grille as standard equipment. You will needto order a panel for the grille and hardware tocomplement your surrounding cabinetry.

While the overlay panel design offers you a moreseamless appearance, you need to be aware ofadjacent cabinets and/or countertops when thedoor is opened. Refer to the full-scale illustra-tions at the end of the Built-In section.

To achieve the overlay look, you need threedifferent panels—the decorative overlay panel, a0.10" (3) spacer panel and a 1/4" (6) backerpanel. Depending on your cabinet manufacturer,this could be one panel routed for differentdimensions or more likely, three different panels.Refer to the Overlay Panel Specifications forcomplete details on the overlay sizing. Inaddition, illustrations 2 and 3 will give you abetter idea of the panel construction and how itinteracts with our frame.

The glass door opening of the standard Model430 is designed to be exposed to room air circu-lation. Decorative overlays on the glass shouldbe kept to a minimum. Also, rails and stiles canbe increased in size but should not exceedcabinet manufacturers‘ standard width. Theycannot exceed overall door panel dimensionsspecified, as they would interfere with the oper-ation of the door.

The back sides of rails and stiles that will bevisible through the glass door will need to befinished. Also, the inside edges of the framesmust be finished to match the front surface.

21/4" (57)Rail /Stile

DoorFrame

5/8"(16)

Glass

Trim Reveal 1/4" (6) min

Rout to 1/4" (6) thickness

Illus. 1

BackerPanel

Spacer Panel

Overlay Panel

1/4" (6).10" (3)

5/8"min(16)

1/4" (6) Backer Panel

21/4" (57) Rail /Stile

.10" (3) Spacer Panel

Overlay Panel

Door Frame Glass

.10"(3)

5/16" (8) min

1/16" (2)

5/32" (4) Door/GrilleTrim

Illus. 2 Illus. 3

M O D E L 4 3 0 – F R A M E D P A N E L S

You cannot use a 1/4" (6) panel to cover theglass door of a framed Model 430. It is finewhen applying a panel to the solid door, but ineither instance, you should consider using raisedpanels with a minimum 5/8" (16) thickness.

When using a raised framed panel, you mustallow for the edge to be routed 1/4" (6) aroundthe panel to ensure a proper fit. Refer toillustration 1.

With the framed Model 430, you will receive anextruded handle identical in appearance to theBuilt-In models. However, it will be an extendedhandle and will enable you to use raised panelswithout providing finger clearance to open thedoor.

IMPORTANT NOTE: Wine Storage models with asolid door are available as a special order andrequire 90 days for delivery. When orderingpanels for a solid door unit, follow the overallpanel dimensions indicated; rail and stile dimen-sions do not apply.






63

M O D E L 4 3 0 – O V E R L A Y P A N E L S

As with the Sub-Zero Built-In models, you havethe flexibility of ordering grilles in a variety ofheights for either the framed or overlay applica-tion. Optional panel grille dimensions for theframed Model 430 are the same as listed forBuilt-In Models 611 and 611G on page 21.Overlay grille panel dimensions for the overlayModel 430, standard 11" (279) grille, are listedbelow. Refer to page 25 for optional grille heightdimensions. The width of the overlay grille,spacer and backer panel will be the same regard-less of the height.

In addition, side panel information for a Model430 is available on page 26 of the Built-Insection. Refer to illustration 12 on page 26 forplacement of toe kick and grille area cut-outs.



84(2134)

4 116

(103)

68(1727)

CENTEREDVERTICALLY

DOORPANEL

TOEKICK

DOOR FRAME(722)7

1628

30(762)


F R A M E D P A N E L S P E C I F I C AT I O N SModel 430 – Framed (F)

Framed Door Panel Width 281/8" (714)

Framed Door Panel Height 6711/16" (1719)





O V E R L A Y P A N E L S P E C I F I C AT I O N SModel 430 – Overlay (O)

Overlay Door Panel Width 287/16" (722)

Overlay Door Panel Height 68" (1727)









G R I L L E P A N E L S P E C I F I C A T I O N SModel 430 – Overlay (O)

Overlay Grille Panel Width 287/16" (722)

Overlay Grille Panel Height* 101/4" (260)


Spacer Panel Height* 95/16" (236)


Backer Panel Height* 915/16" (252)

Grille Panel Weight Limit 15 lbs (7 kg)


*Grille panel dimensions are for standard 11" (279)grille. Refer to page 25 for optional grille heights.

IMPORTANT NOTE: Wine Storage models with asolid door are available as a special order andrequire 90 days for delivery. When orderingpanels for a solid door unit, follow the overallpanel dimensions indicated; rail and stile dimen-sions do not apply.





To install framed oroverlay panels, seethe detailed proce-dures outlined in theSub-Zero WineStorage InstallationInstructions.



64

H A R D W A R E C O N S I D E R A T I O N S

With Models 315W and 424 (overlay), Models427 and 427R (integrated) and the Model 430(overlay), you must supply your own handlehardware. It is recommended you use ouroptional handles and use the pre-drilled holessupplied to locate the handles within the frameof our unit. The metal frame on the door hasnumerous mounting holes on each side toaccommodate Sub-Zero accessory handles.This will allow you to provide the best possiblehandle alignment and not take away from thestrength of the stile in this area after the unit isused a number of times. We recommend using apull handle and not a pull knob.

If you elect to place different hardware on theseunits, we encourage you to fasten the hardwareby passing through our door and attaching thehardware through the Sub-Zero door‘s frame.

Optional stainless steel handles are available in avariety of diameters and lengths, as are handlesto match the color and style of Wolf ovens.Contact your Sub-Zero dealer for specifics.

W I N E S H E L F W O O D F A C I N G

Sub-Zero has provided a natural cherry woodfacing to its wine storage shelves in each model.You can also replace these strips with woodmore complementary to your design andsurrounding cabinetry.

The Wine Shelf Wood Facing illustration on thefollowing page can be used as a full-scaletemplate. You must follow the layout of thisformat to accommodate the shelves properly. Toremove the cherry strips, take the shelves outand remove the screws. Reverse the procedureto affix the new wood.

If you choose to stain or seal the wood facing,be aware that some of these substances arehazardous and will damage stored wine.

When planning for hardware, refer to the

Door Frame Profile full-scale illustration on

the following page to give you a better

understanding of the unit‘s frame and posi-

tioning of the glass for the door. You must

not drill through this glass.




65


The full-scale illus-trations on thefollowing pagesenable you to under-stand some of theunique situationsyou may face as youplan for the installa-tion of the WineStorage units. Usethese illustrations astemplates.

D O O R F R A M E P R O F I L E

A


Glass

A

CL

Cabinet DoorProfile

W I N E S H E L F W O O D F A C I N G

A (WIDTH)

Maximum Thickness


11/2" (38)

5/8"(16)

7/64"(3)

5/64"(2)

23/64"(9)

9/16" (14)

27/32"(21)

This full-scale illustration is typical of theModel 424 door frame profile; details of the otherWine Storage door frames will vary slightly.

This full-scale illustration provides the dimensionsyou will need should you choose to replace thenatural cherry wood facing of each wine shelfwith wood more complementary to your designand surrounding cabinetry.

IMPORTANT NOTE: Dimensions will vary forModel 315W. Additional information can be foundin the Specifications pdf file for Model 315W onour website, subzero.com.

D O O R F R A M E H A N D L E O F F S E TWine Storage Models

Dimension A

Model 315W 1" (25)

Model 424 1" (25)

Model 427 7/8" (22)

Model 427R 7/8" (22)

Model 430 15/16" (24)

IMPORTANT NOTE: Rails and stiles must bea minimum of 21/4" (57) wide (except for therails of Models 427 and 427R, which mustbe wide enough to cover the door hinges).The back sides of rails and stiles that will bevisible through the glass door will need to befinished.

W I N E S H E L F W O O D F A C I N GWine Storage Models

Dimension A

Model 315W* 1015/16" (278)

Model 424 191/2" (495)

Model 424FS 191/2" (495)

Model 427 2015/16" (532)

Model 427R 2015/16" (532)

Model 430 249/16" (624)

*Dimensions will vary for Model 315W.


66

DOOR PANEL

SUB-ZERO DOOR

145˚*

12

(13)

14 (6)*

18 (3)

34 (19)

23 (587)TO BACK OFAPPLIANCE

18

*MODEL 424 MUST EXTEND A MINIMUM1/4" (6) BEYOND THEFRONT SURFACE OF

ADJOININGCABINETRY TO

ALLOW THE MAXIMUMDOOR SWING

SUB-ZERODOOR

DOORPANEL

24 (610)CABINETRYOPENING

23 (600)DOOR PANEL

WIDTH

34

M O D E L 4 2 4 – D O O R C L O S E D A N D 1 4 5 ˚ M A X O P E N I N G

The full-scale illustration shows whatconsiderations you need to make for theinstallation of Model 424 and how themaximum door opening may interact withadjacent cabinets and countertops.


U N D E R C O U N T E R R E F R I G E R A T I O N

67

34"(864)

237/8" (606)

34"(864)

237/8" (606)

34"(864)

237/8" (606)

34"(864)

237/8" (606)

N E W U N D E R C O U N T E R R E F R I G E R A T I O N

Available in 2007

Aside from the full-size models that Sub-Zerooffers in its Built-In and Integrated lines ofrefrigeration and its Wine Storage equipment, weround out our product line-up with a new line ofUndercounter refrigeration available in 2007.

Our new Undercounter line consists of an allrefrigerator model, an all refrigerator beveragecenter, a refrigerator / freezer combination modeland an all refrigerator model designed foroutdoor applications. Included in the line is theUndercounter Model 315I(P) ice maker.

The Undercounter models accept a decorativedoor panel for an overlay or stainless steelapplication and can be built in to fit flush withvirtually any base cabinet style. The outdoorModel UC-24RO is available in classic stainlesssteel only and comes with door panel andhandle in place. Model UC-24RO must also bebuilt-in into cabinetry and is not designed to be afree-standing unit.

A classic stainless steel door panel with handleis available as a sales accessory for ModelsUC-24R, UC-24C and 315I(P). Contact yourSub-Zero dealer for information on accessorypanels and handles. Model UC-24B must beordered as overlay (UC24-B/O) or stainless steel(UC-24B/S).

Sub-Zero Undercounter models are all backed byone of the best warranties in the industry.

A L L R E F R I G E R A T O R

B E V E R A G E C E N T E R

C O M B I N AT I O N

M O D E L U C - 2 4 R

All RefrigeratorS U B - Z E R OW A R R A N T Y

Sub-Zero productsare covered by atwo, five and twelveyear residentialwarranty (one andfive year warrantyfor Model UC-24RO).See warranty detailsat the end of thisguide.

M O D E L U C - 2 4 R O

All Refrigerator

M O D E L U C - 2 4 B

Beverage Center

M O D E L U C - 2 4 C

CombinationRefrigerator /Freezer

O U T D O O R M O D E L

NEW

NEW

NEW

NEW

335/8"(854)

153/16"(386)

I C E M A K E R

M O D E L 3 1 5 I ( P )

Ice Maker

Undercounter models, except Model 315I(P),are Star-K compliant to meet strict religiousregulations in conjunction with specificinstructions found on www.star-k.org.




68

M O D E L U C - 2 4 R













F E A T U R E S


1 Utility Bin

2 Door Shelves

M O D E L U C - 2 4 R


**High altitude glass doors are forinstallations at or above 5,000'(1524 m) in elevation and will betreated as a special order. Please allow90 days for delivery. When ordering,put an (A) after the (B) to obtain thecorrect model number.

**750 ml bottles

Optional stainless steel panels andhandles are ordered and shipped assales accessories for Models UC-24R,UC-24C and 315I(P).

M O D E L U C - 2 4 B

B E V E R A G E C E N T E R


Overlay Design UC-24B/O

Classic Stainless Steel UC-24B/S








Wine Storage Capacity 16 bottles***





Shipping Weight (O) 130 lbs (59 kg)

Shipping Weight (S) 135 lbs (61 kg)

F E A T U R E S

2 Wine Storage Shelves

1 Adjustable Glass Shelf

1 Utility Bin

M O D E L U C - 2 4 B

NEW NEW M O D E L U C - 2 4 C

C O M B I N AT I O NR E F R I G E R AT O R | F R E E Z E R

Available Fall 2007






Wine Storage Capacity 8 bottles***







F E A T U R E S

1 Wine Storage Shelf

1 Adjustable Glass Shelf

1 Door Shelf

Automatic Defrost

Automatic Ice Maker

M O D E L U C - 2 4 C

NEW


69


Classic stainless steel door frontpanel with tubular handle

Classic stainless steel tubularhandle for overlay application

UL approved door lock



M O D E L U C - 2 4 R O

A L L R E F R I G E R AT O RO U T D O O R M O D E L


Available Summer 2007











F E A T U R E S


1 Utility Bin

2 Door Shelves

Door Lock

Classic Stainless Steel Finish

M O D E L U C - 2 4 R O

NEW M O D E L 3 1 5 I

I C E M A K E R


Drain Pump Model 315IP





Ice Storage Capacity 26 lbs (12 kg)




F E AT U R E S

Automatic Ice Maker

Automatic Defrost

Reversible Door Swing

Drain Pump (Model 315IP)

M O D E L 3 1 5 I ( P )



70


Sub-Zero productsare covered by atwo, five and twelveyear residentialwarranty (one andfive year warrantyfor Model UC-24RO).See warranty detailsat the end of thisguide.

U N D E R C O U N T E R F E A T U R E S

Overlay Application. The overlay applicationblends seamlessly into your overall room designand complements surrounding cabinetry. You addthe decorative door front panel and hardware.Sub-Zero accessories handles are available.The overlay application is available for all Under-counter models except Model UC-24RO. ModelUC-24B must be ordered specifically as overlay(UC24-B/O).

Stainless Steel Application. A classic stainlesssteel door front panel and handle is available asan accessory for Models UC-24R, UC-24C and315I(P). Model UC-24B must be ordered specifi-cally as stainless steel (UC-24B/S). ModelUC-24RO is available as a classic stainless steelmodel only and comes with door panel andhandle in place.

Glass Door—Model UC-24B. The full-view glassdoor and accent lighting of Model UC-24Bmatches the appearance of Wine Storage Model424.

Electronic Controls. The electronic controls withdigital readout LCD display are up front and easyto access—not applicable on Model 315I(P).

Glass Shelves. Cantilevered glass shelves areadjustable, easy to clean and spill proof. Theglass floor is also spill proof.

Utility Bin. Refrigerator and combination unitsfeature a clear utility bin for storage of smalleritems.

Wine Storage. Models UC-24B and UC-24Cfeature wine storage of 16 and 8 (750 ml)bottles, respectively. The roller-glide winestorage shelves faced with natural cherry woodhave a three-quarter extension for easy access.

Automatic Ice Maker. Combination ModelUC-24C features an automatic ice maker withclear ice bucket. The ice maker provides high-quality, crescent-shaped ice that won’t stick tothe side of the glass.

Two-Litre Bottle Storage. Models UC-24B,UC-24R and UC-24RO feature two-litre bottlestorage in the bottom door shelf.

Door Lock. A UL approved lock is standard onModel UC-24RO and available as a sales acces-sory for all other models except Model 315I(P).

Sabbath Feature. The Sabbath feature will allowthe lights to remain off during certain religiousobservances—not applicable on Model 315I(P).

Ice Maker. Model 315I(P) provides high-quality,clear ice with a storage capacity of up to 26 lbs(12 kg). The ice is not crescent shaped, butinstead resembles a small barrel.

Drain. Ice maker Model 315I has a gravity drain,while Model 315IP has a built-in pump to allowwater to drain into adjacent sink.


71


Refer to the Installation Specifications for infor-mation regarding area requirements, minimumdoor clearance, placement of electrical andplumbing for Sub-Zero Undercounter models.

The Model 315I can be ordered with or withouta pump. If you order the unit without a pump,you must install a drain. Refer to the illustrationson page 73. The drain must be located in a 2"(51) area centered in the opening for the unit,23" (651) back from the front door.

P L U M B I N G R E Q U I R E M E N T S

For Models UC-24C and 315I(P), rough in thewater supply line. Connect a 1/4" OD copper lineto the house supply with an easily accessibleshut-off valve between the supply and the unit.A minimum of 26" (660) of copper tubing isrequired for the water line for Model UC-24C.

Do not use self-piercing valves. A saddle valvekit (4200880) is available from your Sub-Zerodealer. An in-line filter is required when waterconditions have a high sediment content.

The ice maker operates on constant waterpressure between 20 psi (1.4 bar) and 100 psi(6.9 bar).

IMPORTANT NOTE: In some cases, a reverseosmosis water filter system may not be able tomaintain the minimum pressure consistently.


A 115 V AC, 60 Hz, 15 amp circuit breaker andelectrical supply are required. A separate circuit,servicing only this appliance is required.

All Undercounter models are equipped with apower supply cord with a 3-prong groundingplug, which must be plugged into a mating3-prong grounding-type wall receptacle. Followthe National Electrical Code and local codes andordinances when installing the receptacle. Referto the Installation Specifications illustrations.

IMPORTANT NOTE: The Model UC-24RO isdesigned and safe for use in outdoor applica-tions. When installed outdoors, a ground faultcircuit interrupter (GFCI) is required to reducethe risk of electrical shock. A GFCI is notrecommended for use with other Undercountermodels and may cause interruption of operation.


Model UC-24RAll Refrigerator

Model UC-24BAll RefrigeratorBeverage Center

Model UC-24CRefrigerator | Freezerwith Ice Maker

Model UC-24ROAll RefrigeratorOutdoor Model

Model 315IPIce Maker withDrain Pump



72

341/2"(876)

ROUGHOPENINGHEIGHT

341/4"(870)

MINIMUMHEIGHT

REQUIRED

24" (610)ROUGH OPENING

WIDTH

151/2"(394)

24"(610)

ROUGHOPENING

DEPTH

LOCATE ELECTRICALAND WATER LINE

(MODEL UC24C ONLY)WITHIN SHADED AREA

LOCATE WATER LINE(MODEL UC24C ONLY)WITHIN SHADED AREA

3" (76)

2" (51)

151/2"(394)

1/2" (13)

2" (51)

TOP VIEW

FRONT VIEW

ANTI-TIP BRACKET

I N S T A L L AT I O N S P E C I F I C AT I O N SModels UC-24R, UC-24B, UC-24C and UC-24RO

Overall Dimensions




Finished Opening Dimensions

Opening Width 24" (610)

Opening Height 341/2" (876)

Opening Depth 24" (610)


Models without an ice maker will not requirethe water line connection.

Door swing clearance based on stainless steeldoor panel and handle dimensions.

90˚

26" (660) DOOR CLEARANCE

253/8"(644)

I N S T A L L AT I O N S P E C I F I C AT I O N SModel 315I(P)

Overall Dimensions




Finished Opening Dimensions

Opening Width 151/4" (387)

Opening Height 341/2" (876)

Opening Depth 24" (610)


Refer to the illustrations on the followingpage for additional specifications.

Door swing clearance based on stainlesssteel door panel and handle dimensions.

19"(483)

153/16"(386)

115˚DOOR SWING

341/2"(876)

ROUGHOPENINGHEIGHT

333/4"(857)

MINIMUMHEIGHT

REQUIRED

151/4"min (387)ROUGH

OPENING WIDTH

24"(610)

ROUGHOPENING

DEPTH

LOCATEELECTRICAL

ANYWHERE ONBACK WALL

LOCATION OFWATER LINE

8"(203)

1/2"(13)

TOP VIEW

FRONT VIEW


73



M O D E L 3 1 5 I ( P ) – G R A V I T Y D R A I NO R D R A I N P U M P

The Undercounter ice maker can be ordered witha pump (Model 315IP) or without a pump (Model315I). The model without a drain pump drains itswater by gravity. However, the gravity drainmodel may be converted to a pump modelthrough the installation of a drain pump kit anddrain pump.

Specific step-by-step instructions are includedwith the drain pump kit. Contact your Sub-Zerodealer for specifics.

The drain and inlet water tubes must beplumbed before connecting to the ice maker. Forthe gravity drain, all horizontal runs of drain linesmust have a 1/4" (6) per 12" (305) fall. An air gapwill likely be required between the ice makerdrain tube and the drain/waste receptacle. Astand pipe with a trap below it would be accept-able for the drain/waste receptacle. Refer to theillustrations below.

IMPORTANT NOTE: Poor drainage will cause ahigh rate of ice melting in the bin.

I N S T A L L A T I O N S P E C I F I C A T I O N SModel 315I – Gravity Drain

151/4"(387) MIN.

FRONT VIEW

SHUT-OFFVALVE

WATERFILTERWATER

INLET TUBE

DRAINTUBE

TOP VIEW

SHUT-OFFVALVE

WATERFILTER

341/2"(876) NOMINAL

333/4"(857) MIN.

151/4"(387) MIN.

24"(610)

1/8"(3)

WATERINLETTUBE

DRAINTUBE

LOCATE DRAINWITHIN 2" DIA.AREA 23" BACKFROM FRONT

OF UNIT

FRONT VIEW

SHUT-OFFVALVE

WATERFILTER

WATERINLET TUBE

AIR GAPDEVICE

DRAINTUBE

TOP VIEW

SHUT-OFFVALVE

WATERFILTER

WATERINLET TUBE

DRAINTUBE

AIR GAPDEVICE

24"(609)

1/8"(3)

151/4"(387) MIN.

151/4"(387) MIN.

341/2"(876) NOMINAL

333/4"(857) MIN.

Model 315IP – Drain Pump




74

O V E R L A Y P A N E L S P E C I F I C AT I O N SUndercounter Models

Models UC-24R and UC-24C



Panel Thickness 5/8" (16) min

Panel Weight Limit 20 lbs (9 kg) max

Model UC-24B



Width of Rails and Stiles 21/4" (57) min



Model 315I(P)

Door Panel Width 15" (381)




Rails and stiles must be a minimum of 21/4" (57)wide. They can be increased in size but shouldnot exceed cabinet manufacturers standardwidth. Rails and stiles cannot exceed the overalldoor panel dimensions specified, as they wouldinterfere with the operation of the door. Theback sides of rails and stiles that will be visiblethrough the glass door will need to be finished.Also, the inside edges of the frames must befinished to match the front surface.

O V E R L A Y P A N E L – M O D E L S U C - 2 4 RA N D U C - 2 4 C

The overlay door panel design allows for adecorative panel to cover the door trim for aseamless appearance that will complimentsurrounding cabinetry. You may also choose tomatch the handle hardware of surroundingcabinetry.

Refer to the Overlay Panel Specifications belowfor the panel dimensions of your specific model.Outdoor Model UC-24RO is available as a classicstainless steel model only and comes with doorpanel and handle in place.

O V E R L A Y P A N E L – M O D E L U C - 2 4 B

The overlay door panel applied to the ModelUC-24B will consist of only a frame and will affixdirectly to the door with screws through a seriesof predrilled holes in the perimeter of the door.

The glass door opening of the Model UC-24B isdesigned to be exposed to room air circulation.Decorative overlays on the glass should be keptto a minimum. Refer to the Overlay PanelSpecifications below for panel dimensions.

Models UC-24Rand UC-24C

I N S T A L L A T I O N

To install framed oroverlay panels, seethe detailed proce-dures outlined in theSub-Zero Under-counter InstallationInstructions.

Refer to the full-scale illustrations atthe end of thissection for specificson door openingsand other specifica-tions.

W

H

W

H




Model UC-24B

O V E R L A Y P A N E L – M O D E L 3 1 5 I ( P )

It is important to understand the differences inmounting any wood panel to the Model 315I(P).Refer to the Overlay Panel Specifications belowfor panel dimensions. Also refer to the installa-tion instructions packaged with the unit tounderstand how the panel is installed.

Model 315I(P)

W

H


75


The full-scale illus-trations on thefollowing pagesenable you to under-stand some of theunique situationsyou may face as youplan for the installa-tion of the Under-counter units. Usethese illustrations astemplates.

D O O R F R A M E P R O F I L E – M O D E L U C - 2 4 B

Glass

CL

1" (25)

DOOR FRAME PROFILE

1" (25)


Door Panel Profile

W I N E S H E L F W O O D F A C I N G – M O D E L S U C - 2 4 B A N D U C - 2 4 C

191/2" (495)

Maximum Thickness


11/2" (38)

5/8"(16)

7/64"(3)

5/64"(2)

23/64"(9)

9/16" (14)

27/32"(21)

The full-scale illustration shows the door frameprofile for Model UC-24B.

IMPORTANT NOTE: Rails and stiles must be aminimum of 21/4" (57) wide. The back sides of railsand stiles that will be visible through the glassdoor will need to be finished.

For Models UC-24B and UC-24C, use the full-scaleillustration above as a template if you choose toreplace the natural cherry wood facing withwood more complementary to your design andsurrounding cabinetry.



76

DOOR PANEL

SUB-ZERO DOOR

145˚*

12

(13)

14 (6)*

18 (3)

34 (19)

23 (587)TO BACK OF APPLIANCE

18

*UNDERCOUNTERUNIT MUST EXTENDA MINIMUM 1/4" (6)

BEYOND THE FRONT SURFACE OFADJOINING

CABINETRY TOALLOW THE MAXIMUM

DOOR SWING

SUB-ZERODOOR

DOORPANEL

24 (610)CABINETRYOPENING

23 (600)DOOR PANEL

WIDTH

34

U N D E R C O U N T E R D O O R C L O S E D A N D 1 4 5 ˚ M A X O P E N I N G

The full-scale illustration showswhat considerations you needto make for the installation ofthe Undercounter unit and howthe maximum door openingmay interact with adjacentcabinets and countertops.

S UB - Z E RO P RODUC T SL IM I T E D WARRAN TY

RESIDENTIAL USE ONLY

FULL FIVE YEAR SEALED SYSTEM WARRANTY

LIMITED SIXTH THROUGH TWELFTH YEAR WARRANTY ON THE SEALED SYSTEM

FULL TWO YEAR WARRANTY ON TOTAL PRODUCT*


For five years from the date of original installation, your Sub-Zero warranty covers all parts and laborto repair or replace any components that prove to be defective in materials or workmanship in thesealed system. The sealed system consists of the compressor, condenser, evaporator, drier and allconnecting tubing.

FULL TWO YEAR WARRANTY*

For two years from the date of original installation, your Sub-Zero warranty covers all parts and laborto repair or replace any part of the product, that proves to be defective in materials or workmanship.

LIMITED SIXTH THROUGH TWELFTH YEAR SEALED SYSTEM WARRANTY

From the 6th through the 12th year from the date of original installation, your Sub-Zero warrantycovers all parts that prove to be defective in materials or workmanship in the sealed system (partsonly). The sealed system consists of the compressor, condenser, evaporator, drier and all connectingtubing.

TERMS APPLICABLE TO EACH WARRANTY

All service provided by Sub-Zero under the above warranty must be performed by an authorizedSub-Zero service center, unless otherwise specified by Sub-Zero. Service will be provided in thehome during the normal business hours. This warranty applies only to products installed for normalresidential use. Details regarding a non-residential warranty are available upon request.

The warranty applies only to products installed in any one of the fifty states of the United States, theDistrict of Columbia or the ten provinces of Canada. This warranty does not cover any parts or laborto correct any defect caused by negligence, accident or improper use, maintenance, installation,service or repair, including but not limited to improper removal and reinstallation (whether in the unitor at a remote location) of the condensing unit.

THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THATSUB-ZERO WILL PROVIDE, EITHER UNDER THESE WARRANTIES OR UNDER ANY WARRANTYARISING BY OPERATION OF LAW. SUB-ZERO WILL NOT BE RESPONSIBLE FOR ANY CONSE-QUENTIAL OR INCIDENTAL DAMAGES ARISING FROM THE BREACH OF THESE WARRANTIESOR ANY OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so theabove limitation or exclusion may not apply to you. This warranty gives you specific legal rights andyou may also have other legal rights, which vary from state to state.

To receive parts and/or service and the name of the Sub-Zero authorized service center nearestyou, contact your Sub-Zero dealer, distributor or the Sub-Zero Customer Service Department,P.O. Box 44130, Madison Wisconsin, 53744-4130; check the Constant Care section of our website,subzero.com, or call 800-222-7820.

*Stainless Steel (classic, platinum and carbon) doors, panels, product frames and stainless interiorsurfaces are covered by a limited 60 day parts and labor warranty for cosmetic defects.

*Replacement water filter cartridges are not covered by the product warranty.

77

S UB - Z E RO O U TDOOR P RODUC T SL IM I T E D WARRAN TY

RESIDENTIAL USE ONLY


FULL ONE YEAR WARRANTY ON TOTAL PRODUCT*


For five years from the date of original installation, your Sub-Zero warranty covers all parts and laborto repair or replace any components that prove to be defective in materials or workmanship in thesealed system. The sealed system consists of the compressor, condenser, evaporator, drier and allconnecting tubing.

FULL ONE YEAR WARRANTY*

For one year from the date of original installation, your Sub-Zero warranty covers all parts and laborto repair or replace any part of the product which proves to be defective in materials or workman-ship.

TERMS APPLICABLE TO EACH WARRANTY

All service provided by Sub-Zero under the above warranty must be performed by an authorizedSub-Zero service center, unless otherwise specified by Sub-Zero. Service will be provided in thehome during the normal business hours. This warranty applies only to products installed for normalresidential use. Details regarding a non-residential warranty are available upon request.

The warranty applies only to products installed in any one of the fifty states of the United States,the District of Columbia or the ten provinces of Canada. This warranty does not cover any parts orlabor to correct any defect caused by negligence, accident or improper use, maintenance, installa-tion, service or repair, including but not limited to improper removal and reinstallation (whether inthe unit or at a remote location) of the condensing unit.

THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THATSUB-ZERO WILL PROVIDE, EITHER UNDER THESE WARRANTIES OR UNDER ANY WARRANTYARISING BY OPERATION OF LAW. SUB-ZERO WILL NOT BE RESPONSIBLE FOR ANY CONSE-QUENTIAL OR INCIDENTAL DAMAGES ARISING FROM THE BREACH OF THESE WARRANTIESOR ANY OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so theabove limitation or exclusion may not apply to you. This warranty gives you specific legal rights andyou may also have other legal rights which vary from state to state.

To receive parts and/or service and the name of the Sub-Zero authorized service center nearestyou, contact your Sub-Zero dealer, distributor or the Sub-Zero Customer Service Department,P.O. Box 44130, Madison Wisconsin, 53744-4130; check the Constant Care section of our website,subzero.com, or call 800-222-7820.

*Stainless Steel (classic finish) doors, panels, product frames and stainless interior surfaces arecovered by a limited 60 day parts and labor warranty for cosmetic defects.

78

The information and images in this guide are thecopyright property of Sub-Zero, Inc. Neither thisbook nor any information or images contained hereinmay be copied or used in whole or in part withoutthe express written permission of Sub-Zero, Inc.

©Sub-Zero, Inc. all rights reserved.

3758546 REV-E 3/2009

SUB-ZERO, INC.

P. O. BOX 44130

MADISON, WI 53744 -4130

800.222.7820

SUBZERO.COM

sub-zero design guide - aj madison...sub-zero design guide 3 important note as you follow these...

Documents