sureseal applicator systememanuals.nordson.com/adhesives/english_manuals/1041226.pdf ·...
TRANSCRIPT
SureSeal� Applicator System
Customer Product ManualPart 1041226_03
Issued 10/11
NORDSON CORPORATION DULUTH, GEORGIA USAwww.nordson.com
This document contains important safety informationBe sure to read and follow all safety information in thisdocument and any other related documentation.
Part 1041226_03 � 2011 Nordson CorporationAll rights reserved
For CE Declaration, refer to equipment documentation.
Nordson Corporation welcomes requests for information, comments, and inquiries about its products. General informationabout Nordson can be found on the Internet using the following address: http://www.nordson.com.
Address all correspondence to:
Nordson CorporationAttn: Customer Service11475 Lakefield Drive
Duluth, GA 30097
Notice
This is a Nordson Corporation publication which is protected by copyright. Original copyright date 2003.No�part�of�this�document may be photocopied, reproduced, or translated to another language without the prior written
consent of Nordson�Corporation. The�information�contained in this publication is subject to change without notice.
Trademarks
AccuJet, AeroCharge, Apogee, AquaGuard, Asymtek, Automove, Baitgun, Blue Box, Bowtie, CanWorks, Century, CF, CleanSleeve, CleanSpray, ColorMax,Color‐on‐Demand, Control�Coat, Coolwave, Cross‐Cut, cScan+, Dispensejet, DispenseMate, DuraBlue, DuraDrum, Durafiber, DuraPail, Dura‐Screen,Durasystem, Easy�Coat, Easymove Plus, Ecodry, Econo‐Coat, e.DOT, EFD, Emerald, Encore, ESP, e stylized, ETI ‐ stylized, Excel 2000, Fillmaster,
FlexiCoat, Flex‐O‐Coat, Flow Sentry, Fluidmove, FoamMelt, FoamMix, Fulfill, GreenUV, HDLV, Heli‐flow, Horizon, Hot Shot, iControl, iDry, iFlow, Isocoil,Isocore, Iso‐Flo, iTRAX, Kinetix, LEAN�CELL, Little�Squirt, LogiComm, Magnastatic, March, Maverick, MEG, Meltex, Microcoat, Micromark, MicroSet,
Millennium, Mini Squirt, Mountaingate, Nordson, Optimum, Package of Values, Pattern View, PermaFlo, PicoDot, Porous�Coat, PowderGrid, Powderware,Precisecoat, PRIMARC, Printplus, Prism, ProBlue, Prodigy, Pro‐Flo, ProLink, Pro‐Meter, Pro‐Stream, RBX, Rhino, Saturn, Saturn with rings, Scoreguard,Seal Sentry, Select�Charge, Select�Coat, Select Cure, Signature, Slautterback, Smart‐Coat, Solder Plus, Spectrum, Speed‐Coat, SureBead, Sure Coat,
Sure‐Max, Sure Wrap, Tracking�Plus, TRAK, Trends, Tribomatic, TrueBlue, TrueCoat, Ultra, UpTime, u‐TAH, Vantage, VersaBlue, Versa‐Coat, VersaDrum,VersaPail, Versa‐Screen, Versa‐Spray, Watermark, and When you expect more. are registered trademarks of Nordson Corporation.
Accubar, Advanced Plasma Systems, AeroDeck, AeroWash, AltaBlue, AltaSlot, Alta Spray, Artiste, ATS, Auto‐Flo, AutoScan, Axiom, Best Choice, Blue Series, Bravura, CanPro, Champion, Check Mate, ClassicBlue, Classic IX, Clean�Coat, Cobalt, Controlled Fiberization, Control�Weave, ContourCoat,
CPX, cSelect, Cyclo‐Kinetic, DispensLink, Dry Cure, DuraBraid, DuraCoat, DuraPUR, Easy Clean, EasyOn, EasyPW, Eclipse, e.dot+, E‐Nordson, Equalizer,EquiBead, FillEasy, Fill�Sentry, Flow Coat, Fluxplus, Get Green With Blue, G‐Net, G‐Site, IntelliJet, iON, Iso‐Flex, iTrend, Lacquer Cure, Maxima, Mesa,
MicroFin, MicroMax, Mikros, MiniBlue, MiniEdge, Minimeter, Multifill, MultiScan, Myritex, Nano, NexJet, OmniScan, OptiMix, OptiStroke, Partnership+Plus,PatternJet, PatternPro, PCI, Pinnacle, Plasmod, Powder�Pilot, Powder Port, Powercure, Process Sentry, Pulse Spray, PURBlue, PURJet, Ready Coat,
RediCoat, Royal Blue, Select�Series, Sensomatic, Shaftshield, SheetAire, Smart, Smartfil, SolidBlue, Spectral, SpeedKing, Spray Works, Summit, SureFoam,Sure�Mix, SureSeal, Swirl�Coat, TAH, ThruWave, Trade�Plus, Trilogy, Ultra FoamMix, UltraMax, Ultrasaver, Ultrasmart, Universal, ValueMate, Versa, Vista,
Web Cure, and 2�Rings (Design) are�trademarks of Nordson�Corporation.
Designations and trademarks stated in this document may be brands that, when used by third parties for their own purposes, could lead to violation of the owners' rights.
Table of Contents i
Part 1041226_03� 2011 Nordson Corporation
SureSeal™ Gun System 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Safety Alert Symbols 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Responsibilities of the Equipment Owner 2. . . . . . . . . . . . . . . . . . . . . . . . .
Safety Information 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Instructions, Requirements, and Standards 2. . . . . . . . . . . . . . . . . . . .User Qualifications 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Applicable Industry Safety Practices 3. . . . . . . . . . . . . . . . . . . . . . . . . . . .Intended Use of the Equipment 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Instructions and Safety Messages 4. . . . . . . . . . . . . . . . . . . . . . . . . . . .Installation Practices 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Operating Practices 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Maintenance and Repair Practices 5. . . . . . . . . . . . . . . . . . . . . . . . . . .
Equipment Safety Information 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Equipment Shutdown 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Relieving System Hydraulic Pressure 6. . . . . . . . . . . . . . . . . . . . . . .De‐energizing the System 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Disabling the Applicators 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Safety Warnings and Cautions 7. . . . . . . . . . . . . . . . . . . . . . . .Other Safety Precautions 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .First Aid 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Gun Components 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gun Body and Skid Plate 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Gun Module and Coil 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .RTD‐Heater Assembly 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Nozzle Plate 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Gun Mounting Bracket 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Kit Components 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Carton Application Range 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Gun System Components 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Intended Uses 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Unintended Uses 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Auxiliary Devices and Spare Parts 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contentsii
Part 1041226_03 � 2011 Nordson Corporation
Installation 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Installation Guidelines 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Hydraulic Connections 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Power 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mount the Bracket 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Mount the Gun 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Adjust the Gun to the Manufacturing Line 26. . . . . . . . . . . . . . . . . . . . . . . .Connect the Hose 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Mount the HD4A Gun Driver and EPC‐30 Pattern Control 29. . . . . . . . . . .Connect the HD4A, EPC‐30, and SureSeal Gun 30. . . . . . . . . . . . . . . . . .Connect the EPC‐30 and VersaBlue Melter for Key‐to‐Line Operation 38Connect the EPC‐30 and VersaBlue Melter for Pneumatic Pressure Control 40Set Up the EPC‐30 Pattern Control 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Set Up the HD4A Gun Driver 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Set Up the VersaBlue Adhesive Melter 41. . . . . . . . . . . . . . . . . . . . . . . . . .Test and Adjust the System 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Adjust the SureSeal Adhesive Pattern 43. . . . . . . . . . . . . . . . . . . . . . . . . . .Record System Settings 43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .SureSeal System Settings Log 44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance 45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Relieving Hydraulic Pressure 45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Semi‐Annual Maintenance 45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Annual Maintenance 45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting 46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Adhesive Application Problems 47. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Gun Problems 49. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts Information 54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8‐inch SureSeal Gun Components 54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15‐inch SureSeal Gun Components 56. . . . . . . . . . . . . . . . . . . . . . . . . . . . .SureSeal System Components 58. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Recommended Spare Parts 60. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Gun Nozzles 60. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Cables 60. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Replacement Nozzle Plates 60. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Data 61. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8‐inch Gun 61. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15‐inch Gun 61. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8‐inch Gun Dimensions 62. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15‐inch Gun Dimensions 63. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SureSeal™ Applicator System 1
Part 1041226_03� 2011 Nordson Corporation
SureSeal™ Applicator System
Safety Read this section before using the equipment. This section containsrecommendations and practices applicable to the safe installation, operation,and maintenance (hereafter referred to as “use”) of the product described inthis document (hereafter referred to as “equipment”). Additional safetyinformation, in the form of task‐specific safety alert messages, appears asappropriate throughout this document.
WARNING! Failure to follow the safety messages, recommendations, andhazard avoidance procedures provided in this document can result inpersonal injury, including death, or damage to equipment or property.
Safety Alert Symbols
The following safety alert symbol and signal words are used throughout thisdocument to alert the reader to personal safety hazards or to identifyconditions that may result in damage to equipment or property. Comply withall safety information that follows the signal word.
WARNING! Indicates a potentially hazardous situation that, if not avoided,can result in serious personal injury, including death.
CAUTION! Indicates a potentially hazardous situation that, if not avoided,can result in minor or moderate personal injury.
CAUTION! (Used without the safety alert symbol) Indicates a potentiallyhazardous situation that, if not avoided, can result in damage to equipment orproperty.
SureSeal™ Applicator System2
Part 1041226_03 � 2011 Nordson Corporation
Responsibilities of the Equipment Owner
Equipment owners are responsible for managing safety information, ensuringthat all instructions and regulatory requirements for use of the equipment aremet, and for qualifying all potential users.
Safety Information � Research and evaluate safety information from all applicable sources,
including the owner‐specific safety policy, best industry practices,governing regulations, material manufacturer's product information, andthis document.
� Make safety information available to equipment users in accordance with
governing regulations. Contact the authority having jurisdiction forinformation.
� Maintain safety information, including the safety labels affixed to the
equipment, in readable condition.
Instructions, Requirements, and Standards � Ensure that the equipment is used in accordance with the information
provided in this document, governing codes and regulations, and bestindustry practices.
� If applicable, receive approval from your facility's engineering or safety
department, or other similar function within your organization, beforeinstalling or operating the equipment for the first time.
� Provide appropriate emergency and first aid equipment.
� Conduct safety inspections to ensure required practices are being
followed.
� Re‐evaluate safety practices and procedures whenever changes are
made to the process or equipment.
Refer to User Qualifications on page
SureSeal™ Applicator System 3
Part 1041226_03� 2011 Nordson Corporation
User Qualifications
Equipment owners are responsible for ensuring that users:
� receive safety training appropriate to their job function as directed by
governing regulations and best industry practices
� are familiar with the equipment owner's safety and accident
prevention policies and procedures
� receive equipment‐ and task‐specific training from another qualified
individual
NOTE: Nordson can provide equipment‐specific installation,operation, and maintenance training. Contact your Nordsonrepresentative for information
� possess industry‐ and trade‐specific skills and a level of experience
appropriate to their job function
� are physically capable of performing their job function and are not
under the influence of any substance that degrades their mentalcapacity or physical capabilities
Applicable Industry Safety Practices
The following safety practices apply to the use of the equipment in themanner described in this document. The information provided here is notmeant to include all possible safety practices, but represents the best safetypractices for equipment of similar hazard potential used in similar industries.
Intended Use of the Equipment � Use the equipment only for the purposes described and within the limits
specified in this document.
� Do not modify the equipment.
� Do not use incompatible materials or unapproved auxiliary devices.
Contact your Nordson representative if you have any questions onmaterial compatibility or the use of non‐standard auxiliary devices.
SureSeal™ Applicator System4
Part 1041226_03 � 2011 Nordson Corporation
Instructions and Safety Messages � Read and follow the instructions provided in this document and other
referenced documents.
� Familiarize yourself with the location and meaning of the safety warning
labels and tags affixed to the equipment. Refer to Safety Labels and Tagsat the end of this section.
� If you are unsure of how to use the equipment, contact your Nordson
representative for assistance.
Installation Practices � Install the equipment in accordance with the instructions provided in this
document and in the documentation provided with auxiliary devices.
� Ensure that the equipment is rated for the environment in which it will be
used. This equipment has not been certified for compliance with theATEX directive nor as nonincendive and should not be installed inpotentially explosive environments.
� Ensure that the processing characteristics of the material will not create a
hazardous environment. Refer to the Material Safety Data Sheet (MSDS)for the material.
� If the required installation configuration does not match the installation
instructions, contact your Nordson representative for assistance.
� Position the equipment for safe operation. Observe the requirements for
clearance between the equipment and other objects.
� Install lockable power disconnects to isolate the equipment and all
independently powered auxiliary devices from their power sources.
� Properly ground all equipment. Contact your local building code
enforcement agency for specific requirements.
� Ensure that fuses of the correct type and rating are installed in fused
equipment.
� Contact the authority having jurisdiction to determine the requirement for
installation permits or inspections.
Operating Practices � Familiarize yourself with the location and operation of all safety devices
and indicators.
� Confirm that the equipment, including all safety devices (guards,
interlocks, etc.), is in good working order and that the requiredenvironmental conditions exist.
� Use the personal protective equipment (PPE) specified for each task.
Refer to Equipment Safety Information or the material manufacturer'sinstructions and MSDS for PPE requirements.
� Do not use equipment that is malfunctioning or shows signs of a potential
malfunction.
SureSeal™ Applicator System 5
Part 1041226_03� 2011 Nordson Corporation
Maintenance and Repair Practices � Perform scheduled maintenance activities at the intervals described in
this document.
� Relieve system hydraulic and pneumatic pressure before servicing the
equipment.
� De‐energize the equipment and all auxiliary devices before servicing the
equipment.
� Use only new Nordson‐authorized refurbished or replacement parts.
� Read and comply with the manufacturer's instructions and the MSDS
supplied with equipment cleaning compounds.
NOTE: MSDSs for cleaning compounds that are sold by Nordson areavailable at www.nordson.com or by calling your Nordson representative.
� Confirm the correct operation of all safety devices before placing the
equipment back into operation.
� Dispose of waste cleaning compounds and residual process materials
according to governing regulations. Refer to the applicable MSDS orcontact the authority having jurisdiction for information.
� Keep equipment safety warning labels clean. Replace worn or damaged
labels.
Equipment Safety Information
This equipment safety information is applicable to the following types ofNordson equipment:
� hot melt and cold adhesive application equipment and all related
accessories
� pattern controllers, timers, detection and verification systems, and all
other optional process control devices
SureSeal™ Applicator System6
Part 1041226_03 � 2011 Nordson Corporation
Equipment Shutdown
To safely complete many of the procedures described in this document, theequipment must first be shut down. The level of shut down required varies bythe type of equipment in use and the procedure being completed. If required, shut down instructions are specified at the start of the procedure.The levels of shut down are:
Relieving System Hydraulic Pressure
Completely relieve system hydraulic pressure before breaking any hydraulicconnection or seal. Refer to the melter‐specific product manual forinstructions on relieving system hydraulic pressure.
De‐energizing the System
Isolate the system (melter, hoses, applicators, and optional devices) from allpower sources before accessing any unprotected high‐voltage wiring orconnection point.
1. Turn off the equipment and all auxiliary devices connected to theequipment (system).
2. To prevent the equipment from being accidentally energized, lock andtag the disconnect switch(es) or circuit breaker(s) that provide inputelectrical power to the equipment and optional devices.
NOTE: Government regulations and industry standards dictate specificrequirements for the isolation of hazardous energy sources. Refer to theappropriate regulation or standard.
Disabling the Applicators
NOTE: Adhesive dispensing applicators are referred to as “applicators” insome previous publications.
All electrical or mechanical devices that provide an activation signal to theapplicators, applicator solenoid valve(s), or the melter pump must bedisabled before work can be performed on or around an applicator that isconnected to a pressurized system.
1. Turn off or disconnect the applicator triggering device (pattern controller,timer, PLC, etc.).
2. Disconnect the input signal wiring to the applicator solenoid valve(s).
3. Reduce the air pressure to the applicator solenoid valve(s) to zero; thenrelieve the residual air pressure between the regulator and the applicator.
SureSeal™ Applicator System 7
Part 1041226_03� 2011 Nordson Corporation
General Safety Warnings and Cautions
Table 1 contains the general safety warnings and cautions that apply toNordson hot melt and cold adhesive equipment. Review the table andcarefully read all of the warnings or cautions that apply to the type ofequipment described in this manual.
Equipment types are designated in Table 1 as follows:
HM = Hot melt (melters, hoses, applicators, etc.)
PC = Process control
CA = Cold adhesive (dispensing pumps, pressurized container, andapplicators)
Table 1 General Safety Warnings and Cautions
EquipmentType Warning or Caution
HM
WARNING! Hazardous vapors! Before processing any polyurethanereactive (PUR) hot melt or solvent‐based material through a compatibleNordson melter, read and comply with the material's MSDS. Ensurethat the material's processing temperature and flashpoints will not beexceeded and that all requirements for safe handling, ventilation, firstaid, and personal protective equipment are met. Failure to comply withMSDS requirements can cause personal injury, including death.
HM
WARNING! Reactive material! Never clean any aluminum componentor flush Nordson equipment with halogenated hydrocarbon fluids.Nordson melters and applicators contain aluminum components thatmay react violently with halogenated hydrocarbons. The use ofhalogenated hydrocarbon compounds in Nordson equipment cancause personal injury, including death.
HM, CAWARNING! System pressurized! Relieve system hydraulic pressurebefore breaking any hydraulic connection or seal. Failure to relieve thesystem hydraulic pressure can result in the uncontrolled release of hotmelt or cold adhesive, causing personal injury.
Continued...
SureSeal™ Applicator System8
Part 1041226_03 � 2011 Nordson Corporation
General Safety Warnings and Cautions (contd)
Table 1 General Safety Warnings and Cautions (contd)
EquipmentType Warning or Caution
HM
WARNING! Molten material! Wear eye or face protection, clothing thatprotects exposed skin, and heat‐protective gloves when servicingequipment that contains molten hot melt. Even when solidified, hot meltcan still cause burns. Failure to wear appropriate personal protectiveequipment can result in personal injury.
HM, PC
WARNING! Equipment starts automatically! Remote triggering devicesare used to control automatic hot melt applicators. Before working onor near an operating applicator, disable the applicator's triggeringdevice and remove the air supply to the applicator's solenoid valve(s).Failure to disable the applicator's triggering device and remove thesupply of air to the solenoid valve(s) can result in personal injury.
HM, CA, PC
WARNING! Risk of electrocution! Even when switched off andelectrically isolated at the disconnect switch or circuit breaker, theequipment may still be connected to energized auxiliary devices.De‐energize and electrically isolate all auxiliary devices beforeservicing the equipment. Failure to properly isolate electrical power toauxiliary equipment before servicing the equipment can result inpersonal injury, including death.
HM, CA, PC
WARNING! Risk of fire or explosion! Nordson adhesive equipment isnot rated for use in explosive environments and has not been certifiedfor the ATEX directive or as nonincendive. In addition, this equipmentshould not be used with solvent‐based adhesives that can create anexplosive atmosphere when processed. Refer to the MSDS for theadhesive to determine its processing characteristics and limitations.The use of incompatible solvent‐based adhesives or the improperprocessing of solvent‐based adhesives can result in personal injury,including death.
HM, CA, PC
WARNING! Allow only personnel with appropriate training andexperience to operate or service the equipment. The use of untrainedor inexperienced personnel to operate or service the equipment canresult in injury, including death, to themselves and others and candamage to the equipment.
SureSeal™ Applicator System 9
Part 1041226_03� 2011 Nordson Corporation
Warning or CautionEquipment
Type
HM
CAUTION! Hot surfaces! Avoid contact with the hot metal surfaces ofapplicators, hoses, and certain components of the melter. If contactcan not be avoided, wear heat‐protective gloves and clothing whenworking around heated equipment. Failure to avoid contact with hotmetal surfaces can result in personal injury.
HM
CAUTION! Some Nordson melters are specifically designed toprocess polyurethane reactive (PUR) hot melt. Attempting to processPUR in equipment not specifically designed for this purpose candamage the equipment and cause premature reaction of the hot melt. Ifyou are unsure of the equipment's ability to process PUR, contact yourNordson representative for assistance.
HM, CA
CAUTION! Before using any cleaning or flushing compound on or inthe equipment, read and comply with the manufacturer's instructionsand the MSDS supplied with the compound. Some cleaningcompounds can react unpredictably with hot melt or cold adhesive,resulting in damage to the equipment.
HM
CAUTION! Nordson hot melt equipment is factory tested with NordsonType R fluid that contains polyester adipate plasticizer. Certain hot meltmaterials can react with Type R fluid and form a solid gum that canclog the equipment. Before using the equipment, confirm that the hotmelt is compatible with Type R fluid.
SureSeal™ Applicator System10
Part 1041226_03 � 2011 Nordson Corporation
Other Safety Precautions � Do not use an open flame to heat hot melt system components.
� Check high pressure hoses daily for signs of excessive wear, damage, or
leaks.
� Never point a dispensing handapplicator at yourself or others.
� Suspend dispensing handapplicators by their proper suspension point.
First Aid
If molten hot melt comes in contact with your skin:
1. Do NOT attempt to remove the molten hot melt from your skin.
2. Immediately soak the affected area in clean, cold water until the hot melthas cooled.
3. Do NOT attempt to remove the solidified hot melt from your skin.
4. In case of severe burns, treat for shock.
5. Seek expert medical attention immediately. Give the MSDS for the hotmelt to the medical personnel providing treatment.
SureSeal™ Applicator System 11
Part 1041226_03� 2011 Nordson Corporation
Description This manual provides information about the installation and use of theSureSealt hot melt application applicator (hereafter referred to as applicator).The SureSeal applicator is an electrically activated dispenser that appliesboth a caulking bead and a mini‐bead pattern of hot melt adhesive to aproduct carton.
The mini‐bead/caulking bead sealing pattern reduces the potential for theescape of carton contents or scent, or the infiltration of moisture or insectsinto a product carton.
Applicator Components
The applicator consists of a body with three or four removable applicatormodules, an interchangeable nozzle plate, and a support bracket.
Figure 1 illustrates the applicator components referred to throughout thismanual.
SureSeal™ Applicator System12
Part 1041226_03 � 2011 Nordson Corporation
Applicator Components (contd)
Figure 1 Applicator components
1. Applicator mounting bracket2. Bracket arm3. Heater/RTD cordset4. Clamp handle
5. Gun module cordset6. Skid plate7. Gun module/coil8. RTD clip and screw9. RTD
10. Heater11. Nozzle plate stop12. Nozzle plate13. Clamping plate14. Clamping plate nut
SureSeal™ Applicator System 13
Part 1041226_03� 2011 Nordson Corporation
Applicator Body and Skid Plate
The applicator body houses an replaceable RTD/heater assembly and up toofour replaceable applicator modules.
The skid plate protects the applicator nozzles (Refer to Nozzle Plate) fromdamage caused by the carton flaps.
Applicator Module and CoilApplicator modules are electrically opened in response to current input fromthe Nordson HD4A applicator driver. Modules are spring closed. Theapplicator modules and coils are easily removed for service or replacement.
The 8‐inch applicator uses three applicator modules/coils. The 15‐inchapplicator uses four applicator modules/coils.
RTD-Heater AssemblyThe RTD/heater is a single assembly that can be quickly removed from theapplicator body for service or replacement. The assembly can be installed oneither end of the applicator body.
Nozzle PlateSee Figure 2.
Nozzle plates are custom machined for each application.
Nozzles are available with an orifice size of .014, .016, .018, or .021‐inch andare removed/installed into the nozzle plate using the nozzle wrench that isprovided in the installation kit.
Figure 2 Nozzle detail
SureSeal™ Applicator System14
Part 1041226_03 � 2011 Nordson Corporation
Applicator Mounting Bracket The bracket is adjustable in both the horizontal and vertical dimension toprecisely position the applicator in relation to the carton.
Installation Kit Components SureSeal applicators are shipped with:
� Nozzle wrench
� 45‐degree hose fitting
� Two clamping handles
� Two clamping handle insulators
� Coil of three‐conductor signal wire (PN 931158)
Carton Application RangeSee Figure 3.
SureSeal applicators are available in single and dual 8‐inch (203 mm)configurations, and in a single 15‐inch (381 mm) configuration. Theseconfigurations support adhesive application on carton with flaps from13 mm (0.5 in.) to 178 mm (7 in.) in width.
SureSeal™ Applicator System 15
Part 1041226_03� 2011 Nordson Corporation
Figure 3 Applicator-Carton application range
1. 8-inch, Full overlap (FOL)2. 8-inch, Reverse Fold3. 8-inch, Dual Applicator Suystem4. 15-inch, Full overlap (FOL)5. 15-inch, Reverse fold
SureSeal™ Applicator System16
Part 1041226_03 � 2011 Nordson Corporation
Applicator System Components See Figure 4.
The SureSeal applicator is combined with the following Nordson componentsto form a complete SureSeal adhesive application system.
� EPC‐30 pattern control with I/O module (1)
� HD4A electric applicator driver (2)
� Driver‐to‐applicator module cable (3)
� VersaBlue adhesive melter (4)
� Nordson 5/8‐inch hoses (5)
NOTE: The components listed above are ordered and shipped separatelyfrom the SureSeal applicator.
Intended Uses The SureSeal applicator system is designed for use
� in packaging applications for all standard board weights and flap styles
(full overlap, economy, and reverse fold).
� with electric applicator drivers and pattern controllers designed and
manufactured by Nordson Corporation.
Unintended Uses The SureSeal applicator system is not designed for use
� with high viscosity, heavy bodied, or rubber‐based adhesives.
NOTE: Nordson can test and confirm the performance of a given hotmelt product. Contact your Nordson representative for information aboutadhesive performance testing.
� in explosive environments.
� in applications that require total containment of carton contents or scent,
or total blockage of moisture or insect infiltration into the carton.
SureSeal™ Applicator System 17
Part 1041226_03� 2011 Nordson Corporation
Auxiliary Devices and Spare Parts SureSeal applicators should only be connected to approved auxiliarydevices. Use only new Nordson replacement parts or approved factoryrefurbished parts.
Figure 4 SureSeal Adhesive Application System
SureSeal™ Applicator System18
Part 1041226_03 � 2011 Nordson Corporation
Installation To install the applicator:
1. Mount the applicator bracket.
2. Mount the applicator.
3. Install the melter and connect the hose.
4. Mount the applicator driver and pattern control.
5. Connect the cordsets.
Installation Guidelines To achieve optimal applicator performance, observe the following installationguidelines.
Mounting � Mount the applicator so that the caulking bead mark, which is indicated
on each nozzle plate with the letter “C”, is 6.4 mm (0.25 in.) in from theedge of the carton flap.
� Use a 9.5 mm (0.38 in.) mounting bar.
� Ensure that there is adequate clearance around the applicator to access
and remove applicator nozzles using the wrench provided in theinstallation kit.
NOTE: Refer to Technical Data for information about applicator dimensions.
Hydraulic Connections � Use only one fitting to connect the hose to the applicator.
� Insulate the hose‐to‐applicator joint.
Power � The HD4A electric applicator driver requires a 230 VAC power source.
SureSeal™ Applicator System 19
Part 1041226_03� 2011 Nordson Corporation
Mount the Bracket
CAUTION! Risk of Nozzle Plate Damage!Do not install the nozzle plate until the applicators are mounted. Installing thenozzle plate before installing the applicator can be damaged the nozzleplate.
See Figure 5.
1. Establish a mounting location for the bracket that places the caulkingbead for both the top and the bottom applicator to the outside of themanufacturing line.
See Figure 6.
2. Install the mounting brackets on a rigid support.
Figure 5 Position of the caulking bead with respect to the manufacturing line
SureSeal™ Applicator System20
Part 1041226_03 � 2011 Nordson Corporation
Mount the Bracket (contd)
13 mm(.50 in.)
51 mm(2.0 in.)
152 mm(6.0 in.)
51 mm(2.0 in.)
51 mm(2.0 in.)
25 mm(1.0 in.)
102 mm(4.0 in.)
Figure 6 Mounting bracket bolt pattern
SureSeal™ Applicator System 21
Part 1041226_03� 2011 Nordson Corporation
Mount the ApplicatorSee Figure 7.
1. (Optional) If additional space is required between the applicator and themounting bracket, install the extra set of insulators, which are provided inthe installation kit, between the applicator body and the applicatorbracket.
See Figure 8.
2. Insert each clamping handle (two) through the slot in the bracket arm,and then thread the handle into the applicator bracket. Securely tighteneach clamp.
3. Loosen all of the clamping plate nuts, and then remove and discard theblank nozzle plate.
See Figure 9.
CAUTION! Handle the nozzle plates carefully. The plates are manufacturedout of hardened steel and can break if dropped on or struck against a hardsurface.
4. Refer to the reference drawing provided with each nozzle plate. Thereference drawing indicates the box name, applicator (top or bottom),and the side of the applicator (left or right, when looking at the front of theapplicator) where the nozzle plate belongs.
Insert the correct nozzle plate into the applicator until it contacts the stopon the opposite side of the applicator.
NOTE: Do not discard the reference drawing. It contains importantinformation about setting up the EPC‐30 pattern control.
5. Tighten each clamping plate nut to 20 NSm (15 ft‐lb.).
SureSeal™ Applicator System22
Part 1041226_03 � 2011 Nordson Corporation
Mount the Applicator (contd)
Figure 7 Insulator location (one set shown)
1. Gun body2. Gun bracket3. Insulators
Figure 8 Inserting the clamping handles through the bracket arm
SureSeal™ Applicator System 23
Part 1041226_03� 2011 Nordson Corporation
Figure 9 Installing the nozzle plate
SureSeal™ Applicator System24
Part 1041226_03 � 2011 Nordson Corporation
Adjust the Applicator to the Manufacturing Line
1. Jog or place a carton into position under the applicator.
See Figure 10.
2. Lower the applicator by adjusting the mounting bracket until the cartonflaps are parallel to the skid plate. Ensure that the skid plate does notrestrict the movement of the carton along the manufacturing line.
NOTE: If necessary, pre‐break the carton flaps to ensure that they rideparallel to the skid plate.
See Figure 11.
3. Use the horizontal adjustment of the mounting bracket to position theapplicator so that the caulking bead, which is marked with a “C” on thenozzle plate, is 6.4 mm (0.25 in.) in from the outside edge of the cartonflap.
Figure 10 Carton flap compression
SureSeal™ Applicator System 25
Part 1041226_03� 2011 Nordson Corporation
Figure 11 Adjusting the caulking bead to the carton flap
Module mounting screws
SureSeal™ Applicator System26
Part 1041226_03 � 2011 Nordson Corporation
Connect the Hose NOTE: Refer to the documentation provided with the hose for additionalinstallation details and precautions.
See Figure 1 and Figure 12.
NOTE: The hose must be installed on the same side of the applicator as theRTD/heater assembly.
1. (Optional) Remove the RTD clip, and then remove the RTD/Heaterassembly. Re‐install the assembly on the opposite side of the applicator.
See Figure 13.
2. Remove the hose port plug and Install the 45 degree hose fitting(provided in the installation kit).
3. Connect the hose to the hose fitting. Use two wrenches to securelytighten the fitting.
4. Connect the applicator cordset to the hose.
5. Connect the other end of the hose to the VersaBlue adhesive melter.Refer to the product manual provided with the melter for informationabout connecting the hose and the hose cordset.
6. Check and tighten each module mounting screw.
Figure 12 Installing the RTD/Heater assembly
SureSeal™ Applicator System 27
Part 1041226_03� 2011 Nordson Corporation
Figure 13 Connecting the hose to the applicator, and the applicator cordset to thehose
Mount the HD4A Applicator Driver and EPC-30 Pattern Control For mounting instructions, refer to the product manuals provided with theEPC‐30 pattern control and the HD4A electric applicator driver.
NOTE: You must provide 230 VAC to the HD4A electric applicator driver.
NOTE: The SureSeal system ships with the encoder and encoder cable.The encoder cable (P/N 772052) is 9.1 m (30 ft.) in length.
SureSeal™ Applicator System28
Part 1041226_03 � 2011 Nordson Corporation
Connect the HD4A, EPC-30, and SureSeal Applicator
See Figure 4 for cable locations.
See Figure 14 for the location of HD4A and EPC‐30 terminal blocks.
See Figure 15, 16, 17, 18, 19, or 20 to determine the wiring required for yourapplication.
1. Using the 3‐conductor signal wire provided in the installation kit, connecteach applicator signal output on the EPC‐30 terminal block, to theindicated input on the HD4A terminal block.
2. Connect the brown and the white wire of each HD4A cable(PN 183542) to the appropriate driver output, and then connect theopposite end of the cable to the appropriate applicator module cordset.
Figure 14 EPC-30 and HD4A terminal blocks
SureSeal™ Applicator System 29
Part 1041226_03� 2011 Nordson Corporation
Figure 15 Single 15-inch applicator with full overlap
SureSeal™ Applicator System30
Part 1041226_03 � 2011 Nordson Corporation
Connect the HD4A, EPC‐30, and SureSeal Applicator (contd)
Figure 16 Dual 8-inch applicators with full overlap
SureSeal™ Applicator System 31
Part 1041226_03� 2011 Nordson Corporation
Figure 17 Single 8-inch applicator with full overlap
SureSeal™ Applicator System32
Part 1041226_03 � 2011 Nordson Corporation
Connect the HD4A, EPC‐30, and SureSeal Applicator (contd)
Figure 18 Single 15-inch applicator with reverse fold
SureSeal™ Applicator System 33
Part 1041226_03� 2011 Nordson Corporation
Figure 19 Single 8-inch applicator with reverse fold
SureSeal™ Applicator System34
Part 1041226_03 � 2011 Nordson Corporation
Connect the HD4A, EPC‐30, and SureSeal Applicator (contd)
Figure 20 Single 15-inch applicator with reverse fold/tabbed edge
SureSeal™ Applicator System 35
Part 1041226_03� 2011 Nordson Corporation
This page intentionally left blank.
SureSeal™ Applicator System36
Part 1041226_03 � 2011 Nordson Corporation
Connect the EPC-30 and VersaBlue Melter for Key-to-Line Operation
See Figure 21.
1. Connect the encoder cable (P/N 772052) plug to the encoder, and thenconnect the encoder cable leads to terminal block X8 on the EPC‐30.
Encoder LeadsEPC‐30
Terminal BlockX8
Red 1
Brown 2
Brown/White 3
Orange 4
Orange/White 5
Black 6
Bare wire 7
2. Using signal‐grade cable, connect the motor control output signal fromEPC‐30 terminal block X1 to terminals 1 and 2 in the cable adapterprovided for terminal XS5 on the VersaBlue melter, and then connect thecable adapter to receptacle XS5.
EPC‐30 Terminal
Block X1
VersaBlue
Receptacle XS5
8 when using 4-20 mA 2
9 is common 1
10 when using 0-10 V 2
SureSeal™ Applicator System 37
Part 1041226_03� 2011 Nordson Corporation
X8 X11 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 10
7 8 9 10 7 8 9 10
EPC−30
P/N 772051
P/N 772052
4−20 mA 0−10 V
VersaBlue
XS5
1
2
1
2
Figure 21 EPC-30-to-VersaBlue key-to-line wiring
1. EPC-30 terminal block X8 and X12. EPC-30-to-encoder cable3. Encoder4. Terminal block XS5 on the VersaBlue adhesive melter
SureSeal™ Applicator System38
Part 1041226_03 � 2011 Nordson Corporation
Connect the EPC-30 and VersaBlue Melter for Pneumatic PressureControl
See Figure 22.
1. Using signal‐grade cable, connect terminals 8 and 9 (4–20 mA) orterminals 9 and 10 (0–10 volts) on terminal block X1 of the EPC‐30 to theappropriate terminals (1 and 3 or 2 and 4) inside the cable adapter forterminal XS4 on the VersaBlue adhesive melter.
2. Connect the cable adapter to receptacle XS4.
Figure 22 EPC-30−to−VersaBlue pressure control wiring
SureSeal™ Applicator System 39
Part 1041226_03� 2011 Nordson Corporation
Set Up the EPC-30 Pattern Control Refer to the EPC‐30 product manual for information about setting up theEPC‐30.
NOTE: EPC‐30 settings that are specific to using the EPC‐30 with SureSealapplicators are provided on the reference drawing that is shipped with eachnozzle plate.
Set Up the HD4A Applicator DriverRefer to the HD4A product manual for information about setting up the driver.
The maintenance cycle (holding voltage) must be set to 23%
Set Up the VersaBlue Adhesive Melter Refer to the VersaBlue product manual for information about setting up themelter. Melter settings that are specific to using the VersaBlue melter withSureSeal applicators are:
� Set the key‐to‐line input according to the signal type you are using
(4-20 mA or 0-10 V).
� Adjust the set‐point temperature of the applicator to a maximum of
85 C (365 F).
� Set the motor speed to 50 percent.
� Set the system pressure to 400-600 psi (27.6-41.7 bar).
Module mounting screws
SureSeal™ Applicator System40
Part 1041226_03 � 2011 Nordson Corporation
Test and Adjust the System 1. Bring the melter/applicators up to set point temperature.
NOTE: Check the adhesive MSDS to ensure that you do not exceed themaximum recommended operating temperature for the adhesive.
2. Ensure that all of the module mounting screws are secure.
3. Place a pan or box under the applicator nozzles to catch adhesive.
4. Cycle the purge switch on the HD4A applicator driver to check if adhesiveflows out of the applicator and cuts off cleanly when the applicator closes.
There should be little or no adhesive build‐up between the nozzles andno stringing or angle hair.
If the adhesive cut‐off is not clean, raise the temperature of all channelsby 12 �C (54 �F ). When all channel temperatures stabilize, again cyclethe the HD4A applicator driver and observe the adhesive cut‐off.
5. Continue testing until the cut‐off is clean.
6. Run the line to position a carton under the applicator so that the leadingedge of the carton flap is just under the nozzle plate.
7. Confirm that the carton flaps are parallel with the skid plate.
If the flaps are not parallel with the skid plate, adjust the height of theapplicator. Refer to Adjust the Applicator to the Manufacturing Line,presented earlier.
If the applicator is too low, it can distort the carton, tear the carton flaps.or distort the adhesive pattern.
If the applicator is too high, the outside portion of the adhesive pattern willbe clean and the inside portion of the pattern will be distorted.
8. Operate the line to apply adhesive to five cartons—stopping the line justbefore the last carton folds.
9. Check the adhesive pattern. If the pattern is not correct, refer to Adjustthe SureSeal Adhesive Pattern.
SureSeal™ Applicator System 41
Part 1041226_03� 2011 Nordson Corporation
Adjust the SureSeal Adhesive Pattern It may be necessary to adjust one or more of the following system variablesto achieve a correct and repeatable SureSeal adhesive pattern.
� Application temperature (affects adhesive viscosity)
� Timing settings on the EPC‐30
� Horizontal and vertical positioning of the applicator
� VersaBlue system pressure
� VersaBlue motor speed
Record System Settings Use the SureSeal System Settings log to record the final production settings.
NOTE: Prior to using the log for the first time, make copies for future use.
SureSeal™ Applicator System42
Part 1041226_03 � 2011 Nordson Corporation
SureSeal System Settings Log General Information
Production of:
Adhesive: Manufacturer:
Viscosity: Processing temperature:
Temperature Settings
Tank temperature:
Applicator 1 tempera-ture:
Hose 1 temperature:
Applicator 2 tempera-ture:
Hose 2 temperature:
Applicator 3 tempera-ture:
Hose 3 temperature:
Applicator 4 tempera-ture:
Hose 4 temperature:
Applicator 1 tempera-ture:
Hose 1 temperature:
Applicator 2 tempera-ture:
Hose 2 temperature:
Applicator 3 tempera-ture:
Hose 3 temperature:
Applicator 4 tempera-ture:
Hose 4 temperature:
VersaBlue Settings
Pressure: Grid temperature:
Motor RPM: Tank temperature:
EPC-30 Settings
Pressure: Grid Temperature:
Motor RPM: Tank Temperature:
Top Applicator Delay Duration Delay Duration
Caulking bead (C1):
Mini-bead (C2):
Mini-bead (C3):
Bottom Applicator
SureSeal™ Applicator System 43
Part 1041226_03� 2011 Nordson Corporation
Caulking bead (C1):
Mini-bead (C2):
Mini-bead (C3):
SureSeal™ Applicator System44
Part 1041226_03 � 2011 Nordson Corporation
Maintenance WARNING! Allow only qualified personnel to perform the following tasks.Follow the safety instructions in this document and all other relateddocumentation.
Relieving Hydraulic Pressure 1. Heat the system to operating temperature.
2. Turn the melter pump off.
3. Relieve system hydraulic pressure, refer to the specific instructions inyour melter manual.
4. Make sure that the operator and the area where the applicator is mountedare shielded.
5. Relieve pressure downstream of the pump by triggering each applicatormodule(s) using purge switch on the HD4A applicator driver.
Semi-Annual Maintenance Inspect the applicator and melter wiring for wear or damage.
Annual Maintenance For optimal performance, replace the following components annually. Referto Parts, for ordering information.
� Applicator module coils
� Applicator modules
� Nozzles
SureSeal™ Applicator System 45
Part 1041226_03� 2011 Nordson Corporation
Troubleshooting WARNING! Allow only qualified personnel to perform the following tasks.Follow the safety instructions in this document and all other relateddocumentation.
The procedures in this section cover only the most common problems thatyou may encounter. If you cannot solve the problem with the informationgiven here, contact your local Nordson representative for assistance.
SureSeal™ Applicator System46
Part 1041226_03 � 2011 Nordson Corporation
Adhesive Application Problems
Problem Possible Cause Corrective Action
1. No adhesive flowfrom any module ofthe applicator oroutput too low
No input power Connect power to the melter andauxiliary devices. Make sure that alldisconnect switches or circuitbreakers are on.
Insufficient air pressure to thepiston pump
Verify air pressure by flushing thefilter. Refer to the melter manual.
Melter motor not operating (gearpump)
Verify that motor is on and operating.Refer to the melter manual.
Adhesive level low Add adhesive.
Melter, hose, or applicatortemperature setting is too low
Adjust the setting. Refer to the meltermanual.
System is not at operatingtemperature
Verify that the READY light is on andthe hot melt is molten. Refer to themelter manual.
Hose is clogged Replace the hose.
Nozzle is clogged Check and clean.
Blockage in module Clean and remove blockages andclean parts as needed, or replace thevalve.
Poor electrical connections orincorrect wiring
Check all wires and wire terminationsin the hose heater, output connector,and RTD circuit and repair as needed.
With the system power off, disconnectthe hose cordset from the melter andapplicator. Check for heater andsensor continuity. Also check eachheater to ensure a wire is notgrounded. Replace the hose if there isno continuity or if a heater wire isgrounded.
Defective thermoswitch Check continuity, and replace ifnecessary.
Defective heater/RTD Unplug the applicator coil and verifythat the RTD connections are secure.If so, check the continuity of the RTDacross the RTD pins on the coil, andreplace if needed.
Continued...
SureSeal™ Applicator System 47
Part 1041226_03� 2011 Nordson Corporation
Problem Possible Cause Corrective Action
1.No adhesive flow fromany module of theapplicator or output toolow, contd.
Melter flow control valve set toolow
Increase the system hydraulicpressure (without stalling the motor)by adjusting the flow control valve. Ifthere is no change, inspect the flowcontrol valve for proper operation.Refer to the melter manual.
Adhesive viscosity is too high Increase the overall systemtemperature (melter, hoses, andapplicators). If there is no change,consult the adhesive vendor.
Melter or hose temperature too low Adjust the temperatures. Refer to themelter manual.
Incorrect nozzle size Replace the nozzle with alarger‐orifice nozzle.
Clogged nozzle Check and clean.
Clogged melter manifold filter Clean or replace the filter. Refer to themelter manual.
Clog of unknown origin Purge the system to remove anyobstructions.
Jammed plunger Remove the nozzle plate and verifyadhesive flow.
Replace the valve if needed.
2. Adhesive output toohigh
Defective thermoswitch Check continuity, and replace ifnecessary.
Defective RTD Unplug the applicator coil and verifythat the RTD connections are secure.If so, check the continuity of the RTDacross the RTD pins on the coil, andreplace if needed.
Melter flow control valve set toohigh
Decrease the system hydraulicpressure using the flow control valve.If there is no change, inspect the flowcontrol valve for proper operation.Refer to the melter manual.
Adhesive viscosity too low Decrease the overall systemtemperature (melter, hoses andapplicators). If there is no change,consult the adhesive vendor.
Melter or hose temperature toohigh
Adjust the temperatures. Refer to themelter manual.
Incorrect nozzle size Replace the nozzle with asmaller‐orifice nozzle.
SureSeal™ Applicator System48
Part 1041226_03 � 2011 Nordson Corporation
Applicator Problems
Problem Possible Cause Corrective Action
1. Applicator fails toheat
Poor electrical connections Check all wires and wire terminationsin the hose heater, output connector,and RTD circuit and repair as needed.With the system power off, disconnectthe hose cordset from the melter andapplicator.
Check for heater and sensorcontinuity.
Check each heater to ensure a wire isnot grounded. Replace the hose ifthere is no continuity or if a heaterwire is grounded.
Failed heater control relay Test the applicator heater controlrelay by exchanging it with a workingrelay. Refer to the melter manual.
Defective heater/RTD Unplug the applicator coil and verifythat the RTD connections are secure.If so, check the continuity of the RTDacross the RTD pins on the coil, andreplace if needed.
Failure in temperature control unit Check the operation of the melter ortemperature control unit. Refer to theappropriate product manual.
2. Applicator overheats Incorrect system voltage Ensure that the system voltagesmatch.
CAUTION: The applicator heatervoltage must match the hose voltageand the applicator coil voltage mustmatch the voltage of the externalcontrol device. If these voltages donot match, serious damage will occur.Voltage specifications are stampedon the applicator nameplate cover.
Temperature settings too high Check the component temperaturesettings.
Check the supply hose controller.
Continued...
SureSeal™ Applicator System 49
Part 1041226_03� 2011 Nordson Corporation
Problem Possible Cause Corrective Action
2. Applicator overheats,contd.
Defective heater/RTD Unplug the applicator coil and verifythat the RTD connections are secure.If so, check the continuity of the RTDacross the RTD pins on the coil, andreplace if needed.
Check the supply hose controller.
3. Applicator and supplyhose heats slowly
Incorrect system voltage Ensure that system voltages match.
CAUTION: The applicator heatervoltage must match the hose voltageand the applicator coil voltage mustmatch the voltage of the externalcontrol device. If these voltages donot match, serious damage will occur.Voltage specifications are stampedon the applicator nameplate cover.
Incorrect component wiring Check all wires and wire terminationsin the hose heater, output connector,and RTD circuit. Repair as needed.
Failed heater(s) Check the resistance of the heateracross the appropriate pins on theapplicator coil. If the resistance is notcorrect, replace the heater.
Check the supply hose controller.
4. Applicator will nottrigger
Poor electrical connections Check all wires and wire terminationsin the hose heater, output connector,and RTD circuit and repair as needed.With system power off, disconnect thehose cordsets from the melter andapplicator.
Check the heater and RTD continuity.
Check each heater through wire toensure the wire is not grounded.Replace the hose if there in nocontinuity or if a heater wire isgrounded.
Incorrect component wiring Check all wires and wire terminationsin the hose heater, output connectorand RTD circuit.
Defective thermoswitch Replace the thermoswitch.
Continued...
SureSeal™ Applicator System50
Part 1041226_03 � 2011 Nordson Corporation
Applicator Problems (contd)
Problem Possible Cause Corrective Action
4. Applicator will nottrigger, contd.
Defective heater/RTD Unplug the applicator coil and verifythat the RTD connections are secure.If so, check the continuity of the RTDacross the RTD pins on the coil, andreplace if needed.
Program switch in wrong position Check that the program switch is inthe RUN position.
Defective coil Unplug the applicator coil and checkthe coil resistance across the coil pinson the coil. Ambient=171–201 ohms177 C (350 F)=265 ohms
Blockage in module Clean and remove blockages andclean parts as needed, or replace thevalve.
Adhesive viscosity too high Increase the overall systemtemperature (melter, hoses, andapplicators). If there is no change,consult the adhesive vendor.
External control device (drivers,timers, microswitches, etc.) notworking
Check the operation of the externalcontrol device. Refer to theappropriate equipment manual.
5. Melter heats slowly Incorrect system voltage Ensure that system voltages match.
CAUTION: The applicator heatervoltage must match the hose voltageand the applicator coil voltage mustmatch the voltage of the externalcontrol device. If these voltages donot match, serious damage will occur.Voltage specifications are stampedon the applicator nameplate cover.
Incorrect component wiring Check all wires and wire terminationsin the hose heater, output connector,and RTD circuit. Repair as needed.
Failed heater(s) Check the resistance of the heateracross the appropriate pins on theapplicator coil. If the resistance is notcorrect, replace the heater.
6. Module seat leaks Blockage in module Clean and remove blockages andclean parts as needed, or replace thevalve.
Continued...
SureSeal™ Applicator System 51
Part 1041226_03� 2011 Nordson Corporation
Problem Possible Cause Corrective Action
7. Nozzle heats slowly Incorrect system voltage Ensure that system voltages match.
CAUTION: The applicator heatervoltage must match the hose voltageand the applicator coil voltage mustmatch the voltage of the externalcontrol device. If these voltages donot match, serious damage will occur.Voltage specifications are stampedon the applicator nameplate cover.
Failed heater(s) Check the resistance of the heateracross the appropriate pins on theapplicator coil. If the resistance is notcorrect, replace the heater.
Incorrect nozzle type Some nozzles require extra warm‐uptime or have poor cutoff when theapplicator is mounted horizontally.Contact a Nordson representative forassistance.
Loose nozzle Tighten the nozzle.
Problem with applicator mounting Ensure the applicator is mounted in amanner that prevents heat transfer tothe support bracket.
8. Nozzle leaks Blockage in module Clean and remove blockages andclean parts as needed, or replace thevalve.
Incorrect nozzle type Some nozzles require extra warm‐uptime or have poor cutoff when theapplicator is mounted horizontally.Contact a Nordson representative forassistance.
Loose nozzle Tighten the nozzle.
Problem with applicator mounting Ensure the applicator is mounted in amanner that prevents heat transfer tothe support bracket.
9. Poor adhesive cutoff Blockage in module Clean ad remove blockages andclean parts as needed, or replace thevalve.
Incorrect nozzle type Some nozzles require extra warm‐uptime or have poor cutoff when theapplicator is mounted horizontally.Contact a Nordson representative forassistance.
Continued...
SureSeal™ Applicator System52
Part 1041226_03 � 2011 Nordson Corporation
Applicator Problems (contd)
Problem Possible Cause Corrective Action
9. Poor adhesive cutoff,contd.
Adhesive viscosity too high Increase the overall systemtemperature (melter, hoses, andapplicators). If there is no change,consult the adhesive vendor.
External control device (drivers,timers, microswitches, etc.) notworking
Check the operation of the externalcontrol device. Refer to theappropriate manual.
10. Excessive residue Defective thermoswitch Replace the thermoswitch.
Defective RTD Unplug the applicator coil and verifythat the RTD connections are secure.If so, check the continuity of the RTDacross the RTD pins on the coil, andreplace if needed.
Incorrect nozzle type Some nozzles require extra warm‐uptime or have poor cutoff when theapplicator is mounted horizontally.Contact a Nordson representative forassistance.
Problem with applicator mounting Ensure the applicator is mounted in amanner that prevents heat transfer tothe mounting bracket.
SureSeal™ Applicator System 53
Part 1041226_03� 2011 Nordson Corporation
This page intentionally left blank.
SureSeal™ Applicator System54
Part 1041226_03 � 2011 Nordson Corporation
Parts Information
8-inch SureSeal Applicator Components
SureSeal™ Applicator System 55
Part 1041226_03� 2011 Nordson Corporation
Item Part Description Quantity
— 1054272 GUN,SP8,ELEC,4 MODULE, SPL. —
1 1063031 � MANIFOLD ASSY,4 MODULE,SP8 1
2 1043916 � CORDSET, ARMORED, 500-WATT, T-STYLE 1
3 1043896 � MODULE,ELECTRIC,SP+ 4
4 1043912 � COIL/CORDSET ASSY,SP+ 4
7 1046235 � SPACER,SKID PLATE,FULL,1/8,SP8 1
8 1028944 � PLATE,SKID,SP+ 1
9 982112 � SCR,PAN,SLT,M6X16,ZN 4
12 1028970 � HANDLE BRACKET,SP+ 1
13 1019009 � INSULATOR,E100,.75 ODX.328 ID X.25,14465 6
14 983404 � WASHER,LK,M,SPT,M8,STL,ZN 2
15 982382 � SCR,SKT,M8X40,ZN 2
16 1043892 � RETAINING RING,EXT,.50,E-RING,BOWED 4
17 983414 � WASHER,FLT,M,NARROW,M8,STL,ZN 2
20 1044714 � HANDLE,ADJUSTABLE,M8x1.25,35 2
24 1063040 � PLATE,NOZZLE CLAMP, BACKER, SP8,SPL 1
25 1063041 � CLAMP,NOZZLE PLATE,FRONT,SP8,SPL 1
26 940121 � O RING,VITON,.364ID X .070W,BR,5060 4
27 982709 � SCR,SKT,M5X10,BL 1
28 983401 � WASHER,LK,M,SPT,M5,STL,ZN 1
29 983408 � WASHER,FLT,M,NARROW,M5,STL,ZN 1
30 982028 � SCR,SKT,M5X20,BL 5
31 982436 � SCR,SET,CUP,M8X50,BL 6
32 1049575 � SPCLWSHRM,M8,8.4X16X.1.6,STL,CASE_HARD 6
33 983404 � WASHER,LK,M,SPT,M8,STL,ZN 6
34 1049574 � NUT,HEX,M8,STL,CLASS12 6
37 1046234 � GUARD,NOZZLE CLAMP,BACKER FACE,SP8+ 1
NOTE A: Non‐saleable items are not listed.
SureSeal™ Applicator System56
Part 1041226_03 � 2011 Nordson Corporation
15-inch SureSeal Applicator Components
SureSeal™ Applicator System 57
Part 1041226_03� 2011 Nordson Corporation
Item Part Description Quantity
1 1051434 MANIFOLD ASSY,4MODULEL 1
2 1043916 CORDSET, ARMORED, 500-WATT, T-STYLE 2
3 1043896 MODULE,ELECTRIC 4
4 1043912 COIL/CORDSET ASSY 4
7 1051125 SPACER,SKID PLATE,FULL,1/8 1
8 1051126 PLATE,SKID 1
9 982443 SCR,FLT,SKT,M6X20,BL 6
12 1028970 HANDLE BRACKET 2
13 1019009 INSULATOR,E100,.75 ODX.328 ID X.25,14465 8
14 983404 WASHER,LK,M,SPT,M8,STL,ZN 4
15 982382 SCR,SKT,M8X40,ZN 4
16 1043892 RETAINING RING,EXT,.50,E-RING,BOWED 4
17 983414 WASHER,FLT,M,NARROW,M8,STL,ZN 4
18 719047 FITTING,45,1 1/16-12JIC X 9/16 1
19 183542 CORDSET,2 COIL,18FT EXTENSION 4
20 1044714 HANDLE,ADJUSTABLE,M8x1.25,35 4
24 1051430 PLATE,NOZZLE CLAMP,BACKER 1
25 1051431 CLAMP,NOZZLE PLATE,FRONT 1
26 940121 O RING,VITON,.364ID X .070W,BR 4
27 982709 SCR,SKT,M5X10,BL 1
28 983401 WASHER,LK,M,SPT,M5,STL,ZN 1
29 983408 WASHER,FLT,M,NARROW,M5,STL,ZN 1
30 982028 SCR,SKT,M5X20,BL 7
31 982436 SCR,SET,CUP,M8X50,BL 8
32 1049575 SPCLWSHRM,M8,8.4X16X.1.6,STL,CASE_HARD 8
33 983404 WASHER,LK,M,SPT,M8,STL,ZN 8
NOTE: Non‐saleable items are not listed.
SureSeal™ Applicator System58
Part 1041226_03 � 2011 Nordson Corporation
SureSeal System Components Part Description
VersaBlue adhesive melter VA025-3GGXX6/PAXXXXXCXX
VersaBlue adhesive melter VA025-3HHXX6/PAXXXXXCXX
8048123 VA025-6GGXX6/PAXXXXXCXX
VersaBlue adhesive melter VA025-6HHXX6/PAXXXXXCXX
VersaBlue adhesive melter VA050-3GGXX6/PAXXXXXCXX
VersaBlue adhesive melter VA050-3HHXX6/PAXXXXXCXX
8045268 VA050-6GGXX6/PAXXXXXCXX
VersaBlue adhesive melter VA050-6HHXX6/PAXXXXXCXX
289714 LG9 Tacho Generator
256535 AC 51, extension cable, 5 meter
256552 AC 51, extension cable, 10 meter
107289 Hose, auto, 5/16 x 10 ft, high flex
107310 Hose, auto, 5/16 x 12 ft, high flex
104008 Hose, auto, 5/16 x 16 ft, high flex
223838 Hose/Auto,5/16 x 20 ft, high flex
129576 Hose, auto, 5/8 x 6 ft, high flex
129578 Hose, auto, 5/8 x 10 ft, high flex
129581 Hose, auto, 5/8 x 16 ft, high flex
719047 FITTING,45,1 1/16-12JIC X 9/16- forapplicator, 5/8' hose
203786 Fitting, 1 1/16 UNF-a3/4 UNF- forVersaBlue, 5/8' hose
772004 EPC30 OP Panel W/IO
131739 Power Supply, PS40
772051 Encoder,US Standard
772052 Encoder Cable,
131474 Retro-Reflective sensor
131476 Diffused Reflective sensor
1029762 HD4a Applicator Driver
1043914 SureSeal plus applicator, 3 modules
1048923 SureSeal plus applicator, 4 modules
13597 2 Cable, adapter, 12‐pin M to 6‐pin FT‐style, 24 ft.
Quote Log XXXXXXX
(Contact Nordson for part number)
Nozzle plate
301866 Velcro Strap
1043893 bracket, single applicator
1054337 Bracket, single applicator, bottom
1047855 Bracket, dual‐applicator, top
1054392 Bracket, dual-applicator, bottom
SureSeal™ Applicator System 59
Part 1041226_03� 2011 Nordson Corporation
DescriptionPart
1052833 Kit, flap guide
1055878 Kit, system installation
1019866 Kit, installation, screw‐in nozzle
1039037 Tool, installation, screw‐in nozzle(qty.5)
SureSeal™ Applicator System60
Part 1041226_03 � 2011 Nordson Corporation
Recommended Spare Parts Part Description
1044516 Service kit, electric module
1044515 Service kit, heater/RTD cordset
1044514 Service kit, module, blank
1044513 Service kit, coil/cordset
Applicator Nozzles Part Description
1019849 Nozzle tip kit, screw in, .012
1019860 Nozzle tip kit, screw in, .014
1019861 Nozzle tip kit, screw in, .016
1019862 Nozzle tip kit, screw in, .018
1019863 Nozzle tip kit, screw in, .021
1019864 Nozzle tip kit, screw in, .030
1019865 Nozzle tip kit, screw in, blank
1019914 Kit, installation, screw in nozzle
901915 Kit, nozzle cleaning
1019866 Kit, installation, screw‐in nozzle
1039037 Tool, installation, screw‐in nozzle (qty.5)
CablesPart Description
183452 Cordset, 2‐coil, 18 ft. extension
772052 Cable assembly, encoder, standard
931158 Wire, signal, HD4A–to–EPC‐30, 3‐conductor, 50 ft.
Replacement Nozzle Plates Order replacement nozzle plates by referencing the part number that isstamped on the nozzle plate.
SureSeal™ Applicator System 61
Part 1041226_03� 2011 Nordson Corporation
Technical Data
8-inch Applicator Parameter Value
Operating temperature 204 �C (400 �F) maximum
Working hydraulic pressure 68.94 bar (1000 psi)
Operating speed-maximum(depends on application)
450 carton/minute, 76.2-121.92 m/min./min. (250-400 ft.)
Applicator heating method Cartridge‐type electric resistance heaters
Electrical requirements 230 VAC, 600-900 W,depending on applicator configuration
15-inch Applicator Parameter Value
Operating temperature 230 �C (446 �F) max.
Working hydraulic pressure 68.94 bar (1000 psi)
Operating speed-maximum(depends on application)
450 cartons/min.76.2–121.9 m/min. (250–400 ft./min.)
Applicator heating method Cartridge‐type electrical resistance
Electrical requirements 230 VAC, 600–800 W (depending onapplicator configuration)
SureSeal™ Applicator System62
Part 1041226_03 � 2011 Nordson Corporation
8-inch Applicator Dimensions
SureSeal™ Applicator System 63
Part 1041226_03� 2011 Nordson Corporation
15-inch Applicator Dimensions
SureSeal™ Applicator System64
Part 1041226_03 � 2011 Nordson Corporation