svp series vibrating probe point level sensor
TRANSCRIPT
PRODUCT INTRODUCTION
FEATURESOPERATING PRINCIPLEThe SVP series is a vibrating probe point level sensor utilizing piezoelectric crystal and solidstate electronics technologies to produce vibration in the probe element at a specific frequency and receive electronic feedback. When the probe element is covered or in contact with the target material the vibration is dampened, the electronic feedback changes and presence of the material is thereby sensed by the electronics, which changes the state of the sensor output to indicate material presence. When the probe element is again free of the target material the vibration again is produced, the output state reverts indicating material absence.
1
The SVP series vibrating probe point level sensor is ideal for most dry freely flowing powder and granular bulk solid materials including coffee, milk powder, chocolate, food ingredients, flyash, grains, plastic pellets, glass powder, and much more. Industries that the SVP series is suitable for use include: Ÿ AgricultureŸ Feed & Grain ProcessingŸ Plastic ProcessingŸ Food & IngredientsŸ PharmaceuticalŸ ChemicalŸ Water/WastewaterŸ Many Others
INDUSTRY USE AND APPLICATIONS
Ÿ Universal power supply 20-250VAC/VDCŸ Local LED indication (certain versions)Ÿ No calibration required, easy to setup and useŸ Remote test function allows remote check of
functionalityŸ Standard, extended, pipe extended, cable
extended, anti-corrosive and other versions
STRUCTURE (TYPE A STANDARD)
Vibrating ElementProcess Connection
Housing
TYPES & SPECIFICATIONS
2
SVP1710
20~250Vac/Vdc, 50/60Hz
Max.:15VA
FSH/FSL
177inlbs (20Nm)
Green LED
Red LED
Type A: Standard
Jumper RT1/RT2 for Test
0~6S
380~420Hz
2 hole 3/4"NPT
IP65
142psi (10Bar)
304SS/316SS/316LSS
-40⁰F~176⁰F (-40⁰C~80⁰C)
-40⁰F~176⁰F (-40⁰C~80⁰C)
Inch(mm)
HIGH/LOW
One Relay Output: 5A @ 240Vac, 5A @ 28Vdc (Option: Two Relay Output)One NPN/PNP Output: 400mA @ 60Vac/Vdc (Option: Two NPN/PNP Output)
Die Cast Aluminum (powder coated)
20lbs/ft3 (S.G. 0.32)
3s when the sensor is covered3s when the sensor is uncovered
Operating temp.
Order no.
Ambient temp.
Pressure
Probe material
Supply voltage
Sensitivity
Power consumption
Fail safe mode
Type
Dimensions
Output
Vibrating frequency
Conduit entrance
Protection
Housing material
Delay time
Switching time
Maximum vertical force
Remote test
Minimum density
Normal indicator
Alarm indicator
f5.12(130)
"
5.63(143)
"
10.91(277)
"
1"NPT
3/4"NPT0.79(20)
"
f0.75(19)
"
304SS/316SS/316LSS
304SS/316SS/316LSS
Inch(mm)
f5.12(130)
"
5.63(143)
"
9.98(253.5)
"
3/4"NPT0.79(20)
"
f0.75(19)
"304SS(ETFE Coated)
SVP1710
Type B: Anti-Corrosive Standard
ETFE Coated 304SS(not in contact with material)
3
20~250Vac/Vdc, 50/60Hz
Max.:15VA
FSH/FSL
177inlbs (20Nm)
Green LED
Red LED
Jumper RT1/RT2 for Test
0~6S
380~420Hz
2 hole 3/4"NPT
IP65
142psi (10Bar)
-40⁰F~176⁰F (-40⁰C~80⁰C)
-40⁰F~176⁰F (-40⁰C~80⁰C)
Inch(mm)
HIGH/LOW
One Relay Output: 5A @ 240Vac, 5A @ 28Vdc (Option: Two Relay Output)One NPN/PNP Output: 400mA @ 60Vac/Vdc (Option: Two NPN/PNP Output)
Die Cast Aluminum (powder coated)
20lbs/ft3 (S.G. 0.32)
3s when the sensor is covered3s when the sensor is uncovered
Operating temp.
Order no.
Ambient temp.
Pressure
Supply voltage
Sensitivity
Power consumption
Fail safe mode
Type
Dimensions
Output
Vibrating frequency
Conduit entrance
Protection
Housing material
Delay time
Switching time
Maximum vertical force
Remote test
Minimum density
Normal indicator
Alarm indicator
Inch(mm)
TYPES & SPECIFICATIONS
SVP1711
Type C: Extended Standard
SVP1711
Type D: Anti-Corrosive/Extended Standard
10.83(275~400)
"~15.75"
f0.75(19)
"
f5.12(130)
"
5.63(143)
"
1"NPT
3/4"NPT0.79(20)
"
304SS/316SS/316LSS
304SS/316SS/316LSS
f5.12(130)
"
5.63(143)
"
10.91 .(277~400)
"~15 75"
3/4"NPT 0.79(20)
"
f0.75(19)
"
304SS/316SS/316LSSProbe materialETFE Coated 304SS
(not in contact with material)
304SS(ETFE Coated)
4
20~250Vac/Vdc, 50/60Hz
Max.:15VA
FSH/FSL
177inlbs (20Nm)
Green LED
Red LED
Jumper RT1/RT2 for Test
0~6S
380~420Hz
2 hole 3/4"NPT
IP65
142psi (10Bar)
304SS/316SS/316LSS
-40⁰F~176⁰F (-40⁰C~80⁰C)
-40⁰F~176⁰F (-40⁰C~80⁰C)
Inch(mm)
HIGH/LOW
One Relay Output: 5A @ 240Vac, 5A @ 28Vdc (Option: Two Relay Output)One NPN/PNP Output: 400mA @ 60Vac/Vdc (Option: Two NPN/PNP Output)
Die Cast Aluminum (powder coated)
20lbs/ft3 (S.G. 0.32)
3s when the sensor is covered3s when the sensor is uncovered
Operating temp.
Order no.
Ambient temp.
Pressure
Probe material
Supply voltage
Sensitivity
Power consumption
Fail safe mode
Type
Dimensions
Output
Vibrating frequency
Conduit entrance
Protection
Housing material
Delay time
Switching time
Maximum vertical force
Remote test
Minimum density
Normal indicator
Alarm indicator
TYPES & SPECIFICATIONS
SVP1712
Type E: Pipe Extended (welded pipe)
13.78 ~157.48(350~4000)
" "
f0.75(19)
"
f5.91(150)
"
f1.06(27)
"
f1.14(29)
"
f5.12(130)
"
5.63(143)
"
0.79(20)
"3/4"NPT
1"NPT
304SS/316SS/316LSS
304SS/316SS/316LSS
304SS/316SS/316LSS
304SS/316SS/316LSS
5.63(143)
"
14.25"~157.48"(362~4000)
1-1/4"NPT
3/4"NPT
f0.75(19)
"
f1.06(27)
"
f1.26(32)
"
f5.12(130)
"
12.79"~156.5"(325~3975)
304SS/316SS/316LSS
304SS/316SS/316LSS
304SS/316SS/316LSS
304SS/316SS/316LSS
Inch(mm)
SVP1712
Type G: Pipe Extended (threaded pipe)
20~250Vac/Vdc, 50/60Hz
Max.:15VA
FSH/FSL
177inlbs (20Nm)
Green LED
Red LED
Jumper RT1/RT2 for Test
0~6S
380~420Hz
2 hole 3/4"NPT
IP65
142psi (10Bar)
304SS/316SS/316LSS
-40⁰F~176⁰F (-40⁰C~80⁰C)
-40⁰F~176⁰F (-40⁰C~80⁰C)
HIGH/LOW
One Relay Output: 5A @ 240Vac, 5A @ 28Vdc (Option: Two Relay Output)One NPN/PNP Output: 400mA @ 60Vac/Vdc (Option: Two NPN/PNP Output)
Die Cast Aluminum (powder coated)
20lbs/ft3 (S.G. 0.32)
3s when the sensor is covered3s when the sensor is uncovered
Operating temp.
Order no.
Ambient temp.
Pressure
Probe material
Supply voltage
Sensitivity
Power consumption
Fail safe mode
Type
Dimensions
Output
Vibrating frequency
Conduit entrance
Protection
Housing material
Delay time
Switching time
Maximum vertical force
Remote test
Minimum density
Normal indicator
Alarm indicator
Inch(mm)
TYPES & SPECIFICATIONS
SVP1713
Type H: Coated Cable Extended
5
5.63(143)
"
23.62"~590.55"(600~15000)
1"NPT
3/4"NPT
f1.26(32)
"
f0.75(19)
"
f0.39(10)
"
f5.12"(130)
rubber
22.63"~580.7"(575~14750)
304SS/316SS/316LSS
304SS/316SS/316LSS
304SS/316SS/316LSS
INSTALLATION
6
Top Mount Installation (Figure 1):1. It is recommended that the SVP series vibrating probe point level sensor be installed away from the vessel
fill inlet so as to avoid impact from material that can damage the probe or create false signaling.2. Understand the material flow profile and characteristics in the vessel before choosing a mounting location.
Side Mount Installation (Figure 2):1. It is recommended to install the SVP series vibration probe point level sensor away from the flow of material
from the vessel inlet.2. It is recommended to install a protective baffle or shield above the probe to eliminate impact from any falling
material that can damage the probe or create a false indication of material presence.3. For best performance install side mounted units at a downward angle of approximately 20 degrees to
promote the flow of material away from the probe and to optimize the sensitivity of the unit.4. Make sure conduit entrances are pointing downward during installation to avoid the ingress of moisture into
the enclosure by or through the conduit or conduit connections.
Notice:1. Do NOT climb on the SVP Series vibrating probe or use it as a step.2. Do NOT tighten the unit into its mounting connection by the housing, always tighten using the hex provided
as a part of the probe section.3. Do NOT do anything that might cause bending of the probe section nor should you attempt to modify the
length of the probe section.4. The maximum vertical force of the probe is 177inlbs (20Nm). Ensure that this is not exceed or the probe
may be damaged.
Figure 1
inlet inlet
150mm 150mm
Figure 2
150mm
L
inlet
Probe Type
ORDER INFORMATION
7
C: 20-250Vac/Vdc, 50/60Hz; TWO Relay Output; 5A @ 250Vac / 30VdcD: 20-250Vac/Vdc, 50/60Hz; TWO NPN/PNP Output; 400mA @ 60Vac/VdcE: 20-250Vac/Vdc, 50/60Hz; ONE Relay Output; 5A @ 250Vac / 30VdcF: 20-250Vac/Vdc, 50/60Hz; ONE NPN/PNP Output; 400mA @ 60Vac/Vdc
Model
Housing
0: Standard
Conduit Entrance
0: 3/4"NPT
Power & Output
Enclosure Type0: Explosionproof version without LED Lens1: Non-explosionproof version with LED Lens
0: Standard1: Extended
2: Pipe Extended3: Cable Extended
A: Standard B: Anti-Corrosive StandardC: Extended StandardD: Anti-Corrosive/Extended StandardE: Pipe ExtendedG: Pipe Extended Kit (customer supplies pipe)H: Coated Cable Extended
Probe Material0: 304SS1: 316SS2: 316LSS
Probe Length
Process Connection
Threaded:CU: 3/4" NPT*DU: 1" NPT
* Probe Type B, D, E, G and H probes only** Probe Type C, J and K MUST use one of these choices (no thread for these)
3U: 1-1/4" NPTEU: 1-1/2" NPT
Remarks
Specify exact length required
SVP171 0 0
Type A, B, can select XType C D can select 0 (use below table)Type E, G can select 0~7 (use below table)
A: Range from 198” to 217”B: Range from 218” to 236”C: Range from 237” to 256”D: Range from 257” to 276”E: Range from 277” to 295”F: Range from 296” to 315”G: Range from 316” to 335”H: Range from 336” to 354”J: Range from 355” to 374”K: Range from 375” to 394”L: Range from 395” to 413”
M: Range from 414” to 433”N: Range from 434” to 453”P: Range from 454” to 472”Q: Range from 473” to 492”R: Range from 493” to 512”T: Range from 513” to 532”U: Range from 533” to 551”V: Range from 552” to 571”W: Range from 572” to 591”S: Special
X: Standard0: Below 19” (500mm)1: Range from 20” to 39” 2: Range from 40” to 59” 3: Range from 60” to 79” 4: Range from 80” to 98” 5: Range from 99” to 118” 6: Range from 119” to 138” 7: Range from 139” to 157” 8: Range from 158” to 177”9: Range from 178” to 197”
FO: 2” ANSI 150LB**FP: 2” ANSI 300LB**
HO: 3” ANSI 150LB**HP: 3” ANSI 300LB**
IO: 4” ANSI 150LB**IP: 4” ANSI 300LB**
Type F, H can select 1~W (use below table)Type G and H can select X, 1-A (use below table)
Aplus Finetek Sensor, Inc.
Global Network
Represented by:
Taiwan
TEL: 886-2-2269-6789FAX: 886-2-2268-6682EMAIL: [email protected]
FINETEK CO., LTD.
China
TEL:86-21-6490-7260FAX: 86-21-6490-7276EMAIL: [email protected]
FINE AUTOMATION CO., LTD.
Singapore
TEL:65-6452-6340FAX: 65-6734-1878EMAIL: [email protected]
FINETEK PTE LTD.
California, U.S.
TEL: 1 909 598 2488 FAX: 1 909 598 3188EMAIL: [email protected]
APLUS FINETEK SENSOR INC.Germany
+49-(0)6142-17608-0FAX: +49-(0)6142-17608-20EMAIL: [email protected]
TEL:
Asia North Amerca Europe
Illinois, U.S.
TEL: 1 815 632-3132 FAX: 1 815 716 8464EMAIL: [email protected]
APLUS FINETEK SENSOR INC.
Taiwan
China
U.S.
Germany
U.S.
Singapore