System Instructions Revision R7A

FFZ / FFV ACROBAT

This document explains revision R7A Acrobat software.

R7A software is only compatible with new versions of FFZ or FFV devices.

SOFTWARE

The FFV is a smal l unit i t ’s only 5x25x25 mm in size.

Predict ion output is vibration.

Clocking switch is soldered on the board. Addit ional vert ical switch to the system can be added for a mouth clocking. I t ’ s located in middle of the board so when it ’s placed in between teeth the board goes up and down the teeth by 10mm.

Power is 3V button cel l battery CR2032 (FFV system can use one battery per season so get them bulk on eBay as 50 for under $10.)

System response t ime is about 0.000002 seconds and calculation is done with resolution of 0.001 seconds.

FFV, is designed to be used mostly for ball clocking by hand or in between teeth. The FFZ can be used in hand but is mostly used for foot clocking.M ous e c l i c k f o r nex t s l i de

FFV BRIEF DESCRIPTION

FFV - LOOK AND FEEL

• Here you can see top and bottom view of the FFV circuit board.

• At top left corner there is a clocking switch, on the right is small vibrating motor and at the bottom is a battery compartment.

• On the other side is a power switch and electronics parts. The systems main brain is a 44 pin microcontroller. The motor is controlled by transistor T1 and diode D2 protects the circuit form reversed induction the motor could make.

• Two connectors marked in red are place where additional vertical clocking switch may be soldered for an option of mouth clocking. Connectors circled in blue are connections for programmer; where the first squared one pad is to connect pin 1 of the programmer.

• FFV’s board is placed inside black plastic tube heat shrunk to the size of the board to take it in the smallest size but to still protect the board.

• Insert the battery, slide the power switch S1 to the left and you should feel gentle vibrations the system makes. The printed circuit board is very small in size , its not a full square since the corners and switch area are curved, but by total area it’s less then ½ of casino chip.

• A skilled player may hold it in between fingers, playing cards, inside top shirt pocket, trousers pocket etc. On the board you also can see 2 holes which can be used to tight the board to something if you need it.

This applies only to FFZ roulette computers.

Plug in the clocking switch Moisturize your skin with some kind of hand cream where

you going to place the FFZ. (Your own salvia is good) Place the FFZ’s golden plates against your skin Press and hold the clocking switch Switch the power ON. The FFZ will start giving zaps which will increase in strength.

When it reaches your desired level release the switch. The system will memorize the setting for future use. You can readjust it the same way at any time.

ADJUSTING ZAP STRENGTH

Predicting roulette spins at any moment during the spin.Multiple predictions during the same spin.Double prediction – in the case you didn’t see fi rst

prediction. Indicator of predictions quality. Independent clock (CW) or anti clock way (ACW) setup

and predictions.Main independent Off set Adjustment for CW and ACW

ball directions.Up to 20 individual off set adjustment for particular ball

speed ranges. Independent setup for diff erent diamonds on the wheel.Accuracy settings.

SYSTEM FEATURE

The Acrobat software can predict at any moment during the spin. Once you set it, all you need is to clock the rotor than at any moment during the spin clock at least two ball rotations. As soon after clicking the system will predict. If you continue clocking the system will predict again but this time when calculating result, it will use times from all 4 clocked ball rotations.

Multiple predictions are unique to Myrulet computers and it is a good way of testing systems linearity of prediction or to increase accuracy with more ball rotations clocked.

After prediction even if you don’t clock the ball for more rotations the system predicts once more. It calculates ball and rotor movement and predicts again when the ball is above same number. It’s just in case if you didn’t see it well when predicting fi rst time.

SOME FEATURES EXPLAINED

Predict ion can be marked on 3 ways

1. Normal predict ion zzz. The system produce short zzz at the moment when the bal l is over predicted number.

2. Marked especial predict ion, zzz…zzz. When sett ing the system after c locking bal l rotat ions you can select normal predict ion or Special ly marked predict ion. For example you can set to special predict ion spin where the bal l h i ts very n icely d iamond or spins where you’ve adjusted independent off set to be able to d iff erent iate i t form the other spins.

3. Warning predict ion zzz. .zzz. .zzz repeats 3 t imes. The system automatical ly generates th is , when there is a h igh r isk of wrong predict ion. When the c locked bal l t ime is equal ly d istanced to two setup samples and with d iff erent fi nal outcome where the d iff erence is greater than plus or minus 6 pockets.

This makes the system ful ly capable of taking an advantage of 2 or 3 dominant d iamonds on a semi t i l ted roulette wheel . In s imple words even i f the bal l has h igh chance to h it d iff erent d iamonds the system wi l l predict normal ly as long as the result is good whi le i t a lways calculates the best result for each diamond separately.

INDICATOR OF PREDICTIONS QUALITY

The system fully and independently handles clock or anti clock ball directions.

When setting or playing the system, you have menu option1. zzz2. zzz…zzz

Where either 1 or 2 can be dedicated for clock or anti clock ball direction, but of course if in set up direction menu (1) is selected for spins where the ball travels in clock way direction same should be used when playing.

FFZ/FFV systems to be able to predict don’t really need to know ball direction as talking computers do. This is purely to increase advantage if the wheel is not fully symmetrical. For that reason this option doesn't have to be exclusively used for CW or ACW ball direction but it can be used to play simultaneously at two roulette tables.

INDEPENDENT CLOCK (CW) OR ANTI CLOCK WAY (ACW)

When playing before each spin you need to select (1) or (2) for bal l d i rect ion based on select ion dur ing setup.

When select ing from (1) or (2) , br iefl y press the switch and you are ready to play.

Alternat ively when select ing (1) or (2) you can press and hold the switch pressed. The system wi l l start g iv ing zzz…….zzz….etc with t ime of one second in between them.

Releasing the switch after system gives 10 zzz’s wi l l set the main off set to + 10 pockets. I f later on you want to change i t you can repeat the process. The system always adds i t to the previous off set. I f you for example add +30 pockets i t is actual ly same as deduct ing 7 pockets. Once you select Main Menu (1) to set the system al l off sets reset to zero.

I f once you add off set 5 then 3 then again 2 the tota l off set wi l l be 5+3+2=10, I f once you add 18 and then again 20 the off set wi l l be 38 which real ly is 38-

37=1 While you holding the switch pressed after 37 zzz, the system wi l l make a smal l

brake then start again f rom 1.

MAIN INDEPENDENT OFFSET ADJUSTMENT FOR CW AND ACW

After powering the system the system will respond with 7 pulses.Then it will go into the menu which gives you 6 main options to select.

7 Pulses Start of the menu

menu1 –one pulse menu2 –block of two pulses menu3 –block of three pulses menu4 –block of four fast pulses menu5 –block of fi ve fast pulses menu6 –block of six fast pulses

If after menu6 nothing is selected, the system goes back and repeats all menu options again, until you select something.

START AND SYSTEM MENU

Pre s s i n g a n d re l e a s i n g t h e s w i t c h a f t e r m e n u 1 t a ke s t h e s y s t e m t o S E T m o d e , w h e re y o u n e e d t o c l o c k t h e b a l l ro t a t i o n s o f o n e s p i n . ( o n l y b a l l ro t a t i o n s ) . T h i s i s a fi r s t s t e p a n d o n a n e w w h e e l y o u p l a y , a l w a y s n e e d s t o b e d o n e . T h e s p i n m a y h a v e 2 0 o r m o re b a l l ro t a t i o n s . B u t y o u d o n o t h a v e t o c l o c k t h e m a l l . Fo r ex a m p l e i f y o u g o i n g t o p re d i c t n o t e a r l i e r t h a n a ro u n d 8 ro t a t i o n s t o t h e e n d o f s p i n i t ’ s e n o u g h t o c l o c k l a s t 1 2 ro t a t i o n s .

S i n c e t h e s y s t e m w o rk s i n d e p e n d e n t l y f o r d i ff e re n t b a l l d i re c t i o n s fi r s t y o u n e e d t o s e l e c t b a l l d i re c t i o n . D u r i n g t h e s e t u p p ro c e s s , b e f o re s e t t i n g e a c h s p i n t h e s y s t e m re p e a t s 1 t h e n 2 p u l s e s w h i c h y o u s e l e c t f o r b a l l d i re c t i o n . Le t s s a y ( 1 ) p u l s e w i l l b e w h e n t h e b a l l i s t r a v e l i n g i n c l o c k b a l l d i re c t i o n .

Af t e r s e l e c t i n g ( 1 ) t h e s y s t e m re p e a t s z z z e v e ry 2 s e c o n d s .I f ( 2 ) w a s s e l e c t e d t h e s y s t e m w i l l re p e a t z z z… zz z e v e ry 2 s e c o n d s .

Af t e r s e l e c t e d b a l l d i re c t i o n t h e s y s t e m i s re a d y t o c l o c k b a l l ro t a t i o n s . E a c h t i m e w h e n t h e b a l l i s p a s s i n g y o u r o b s e rv i n g d i a m o n d p re s s a n d re l e a s e t h e c l o c k i n g s w i t c h . D o i t f o r e v e ry b a l l ro t a t i o n f ro m t h e m o m e n t y o u s t a r t u n t i l t h e e n d o f t h e s p i n . T h e m a x i m u m n u m b e r o f b a l l ro t a t i o n s t h a t t h e s y s t e m c a n m e m o r i s e i s 2 1 . I f y o u c l o c k 2 5 i t d o e s n ’ t m a t t e r t h e s y s t e m m e m o r i s e s o n l y l a s t 2 1 . I t a l s o m e a n s t h a t t h e e a r l i e s t p o s s i b l e p re d i c t i o n i s 1 9 b a l l ro t a t i o n s b e f o re t h a n t h e b a l l d ro p s . Fo r t h e s y s t e m t o b e s e t a m i n i m a l n u m b e r o f ro t a t i o n s i s 6 .

N e w w i t h t h e Ac ro b a t s o f t w a re i s t h a t i f t h e b a l l o n t h e e n d m a ke s a d d i t i o n a l ¼ o r ½ o r ¾ o f ro t a t i o n y o u n e e d t o c l o c k a n d t h a t p a r t .W h e n y o u fi n i s h c l o c k i n g b a l l ro t a t i o n s s t o p p re s s i n g t h e s w i t c h a n d w a i t f e w s e c o n d s . T h e s y s t e m a n a l y s e s t h e c l o c ke d b a l l t i m e s a n d i n c a s e o f a n e r ro r i t w i l l re s p o n d w i t h a s e r i e s o f r a p i d p u l s e s a n d t a ke y o u b a c k t o a n e w s t a r t , s e l e c t i n g b a l l d i re c t i o n m e n u ( 1 ) o r ( 2 ) , s o y o u c a n re p e a t t h e “ S E T” p ro c e s s a g a i n .

MENU 1, SET

During clocking ball rotations or after fi nishing it, good enough is to know that many rapid zaps is warning about bad clocking. But you can notice that rapid zaps are not always the same.

For example Error 2 is represented with block of 2 pulses rapidly repeating, Error 3 would be block of 3 pulses and so on.

Meaning of errors;

Error = 2 During set up. Ball rotation you clocked is shorter than the previous one. Or during play Error 2 means ball clocking is to long, more then 2000ms per rotation.

Error = 3 If during set up you have less then 7 rotations clocked.

Error = 4 Rotation you clocked is far much longer then previous one to protect you from miss clicking ball rotation.

UNDERSTANDING SETTING ERRORS

During setup process clocking can be done at any diamond (not only the dominant one ) But when playing you have to use same diamond you used during the setup.

After clocked ball rotations the system fi rst responds with 1 to 4 zzz’s. I f the ball made 1/2 extra from posit ion you’ve clocked, the system will respond with 2 zzz’s (diamond 2). Diamond 1 is ¼ form posit ion you clocked, diamond 3 is ¾ and diamond 4 is the diamond where you were clocking. Diamond 4 is represented with 4 zzz’s.

This indication is for safety. During my tests I didn’t make any errors, from clocked data the system was always capable to defi ne at which diamond the ball dropped, but I left it there just because in casino it may be harder to be accurate than at home with a controlled environment.

In the case of mismatch what the FF gives as a feedback, and diamond where the ball actually hits; do not save that spin!

SETTING

After successful clocking the setup spin and diamond hit indicator, the system repeats menu with 3 possible selections. (1-3 zzz’s) Please do not hurry here to not make mistake and for example save spin with parameters you do not want to play. Systems undo feature is not added, it may be added with other program revision.

I f there was an error during process of clocking the ball , the FF wil l repeat rapid zaps few times and take you back to start of menu 1-2 where you need to select the ball direction.

Save menu options

1. Save the spin2. Save the spin on a special way. This spins wil l be marked with

prediction zzz…zzz If after menu 2 you press and hold the switch pressed you can also adjust individual off set for this ball speed range.

3. Don’t save spin and go back to start of setting to select ball direction.

SAVING THE SPIN END EXIT

Exit wi thout saving

To exi t the sett ings cancel a l l what you did and to go back to previous sett ings switch the power off . During the set up al l data is saved in temporar i ly Ram. The system saves permanently data to EEProm only when you properly exi t the set up. On power up the system always loads the saved data from EEprom. So i f you have previous ly played i t wi l l restore without new sett ings added.This is to avoid mistakes i f by mistake you saved set spin you didn’t want.

Exit and save new added spins

To exi t the sett ings and to go back to main menu at start of set up process from bal l d i rect ion (1) or (2) select any; press and hold the switch pressed for more then 2 seconds. Release the switch and the system wi l l take you back to the main menu. You can do i t a lso when is t ime to c lock the bal l rotat ions press and hold the switch pressed unt i l you feel zaps / v ibrat ion than release the switch. Ether way the system wi l l save your sett ings in permanent memory and take you back to the main menu. Please do not mistaken this with doing the same when playing outs ide of set menu, where fi rst opt ion wi l l adjust the main off set and the second one is for hal f rotor c locking.

EXITING THE SETUP MENU

Dur ing the set up you can set indiv idual off set for that part icular bal l speed range by select ing SAVE 2 and hold ing the switch pressed.

Let ’s say one setup spin the bal l h i ts d iamond very low and stops on rotor instant ly. I f normal ly off set is that the bal l jumps 11 pockets, th is one you can set to (1 ) s ince the bal l most ly doesn’t jump. To adjust i t to -3 pockets add 37-3=34 pockets off set .

When you play each t ime when the bal l i s wi th in that spin range the system wi l l expect instant bal l stop, predict i t wi th -10 pockets f rom main off set and mark that spin with zzz…zzz Such sett ing can s ignifi cant ly increase your advantage.

Predict ing how the bal l jumps is l imited, don’t expect f rom the system to get i t r ight a l l the t ime also you need to understand that with later predict ions dur ing the spin th is opt ion wi l l be more accurate.

Also not ice that th is explanat ion is s l ight ly d iff erent then i t was expla ined at forum.

First opt ion was that the system adds both off sets so i f the main off set is 11 pockets and i f the bal l wi th part icular speed stops instant ly you would have to adjust indiv idual off set to -11 to cancel i t . New way adds to the predict ion only one off set i f indiv idual off set is not adjusted the system wi l l add main off set , i f indiv idual off set is adjusted the system wi l l ad i t and ignore the main off set . I t ’s easier.

INDIVIDUAL OFFSET

If you made a mistake and not sure where in game mode you are the system will in maximal 16 seconds take you back to start of selecting ball direction. For same reason 16 seconds is maximal time for rotor clocking and also the maximal waiting time in between rotor clocking and ball clocking. Maximal time for two ball rotations clocked is 2 seconds.

For example you may selected wrong ball direction.Press the switch to start clocking rotor then if you just wait 16 seconds without pressing the switch the system will take you back to start where you can select it again.

SMART BACK TO START

INDIVIDUAL OFFSET EXAMPLE

Setting main offset to 5 and when setting the system some spins where the ball hits middle of diamond you can add +14 pockets as an individual offset. This is only examples, on the other wheels may be different.

If using this of course it may help to increase your advantage due to some predicting of ball jumps scatter but always be sure that you know what you doing.

Alternatively based on this example you could set the main offset to 14 and spins when the ball hits low diamond part adjust individual offset to 6 pockets. That would be the most common adjustment.

Also have in mind that the FF most likely will predict exactly where the ball drops on rotor, it is different since on this picture it’s how the ball jumps from the diamond not rom the moment when it hits the rotor.

On this picture red line facing upwards is diamond position. Blue lines representing different spins and how far the ball stops form the diamond. There are 3 scenarios based on where on diamond the ball hits, top, middle and bottom. You can see with top hits the ball mostly stops within 4-6 pockets from the diamond, with middle hits it’s 13-14 pockets and with bottom hit the scatter is wider but still it’s mostly around 4-6 pockets.

If setting the system for a tilted wheel with 2 dominant diamonds it is recommended to do few set spins on each of two diamonds. If when ball is in opposite direction mostly hitting diff erent diamonds you can set the system on them since the system has independent CW and ACW settings.

Spins when the ball doesn’t hit any of DD do not save. Because of the systems Accuracy Settings such spins will not be predicted. Alternatively use especial save (2) and do not play when the system predicts with zzz…zzz.

2-4 sets per diamond is ok also have in mind the system can save 20 spins in total for CW and ACW ball directions. If you set more, fi rst spins you’ve saved will pop out.

SETTING ADVICE

Restore

This programs version on power up automatically restores the previously played game. It includes the set up spins and the off set . From menu select accuracy and you are ready to play. The system keeps everything saved all the time until menu 1 is selected which means New Setup and all your settings will be deleted. When exiting set up, new settings will replace old settings in the systems permanent memory.

SYSTEMS MEMORY

Menu selection 2-5 is accuracy sett ing.

Select 2-5 from main menu based on amount of samples during set up you took. You can look at i t as selecting how far the clocked bal l speed can be from saved samples in ms for the system to predict.

2=20, 3=30 ,4=40, 5=50 mil l iseconds.

I f for example 3 as 30 ms. is selected it also defi nes 30 ms. as a range where the system checks i f there is another set sample that would predict the bal l with a diff erent result to give a warning prediction.

For example set the system with only one spin on a good dominant diamond hit , select accuracy 5 and you wi l l be playing similar to previous program version R6A. Select accuracy 2 and you wi l l get only few spins predicted but most l ikely al l predicted spins wi l l hit that part icular diamond.

MAIN MENU 2-5

This is almost same as main menu 1 to set the system.

If you select menu 1 all previous settings will be lost including off set.

If you select menu 6 you can go back to settings and add more data. Menu 6 will let you set it but it also keeps previous settings.

For example you can set the system to a single diamond, play adjust off sets. Then later on you wan to add more sample spins or set some spins for additional diamond. Select menu 6, set and go back to play. When exiting set up, the system will also save new spins in to the systems permanent memory.

MAIN MENU 6

 I f during the game you want to go back to menu you do not have to go to toi let or remove battery to reset power or to even look the FF system.  Simply when it is t ime to clock the rotor Press and hold the switch ( 8 seconds ) as you do half rotor clocking unti l the system starts giving pulses.

At that moment open the switch and the system wil l take you back to menu where you can do anything you want.  I f you keep the switch pressed for longer than 10 seconds you wil l lock the system.

Locking the system is not included in this program version. It may be added in next program revision.

 

BACK TO THE MENU/LOCK

If spins are short, and if rotor is slow you can use half rotor clocking.

For a full rotor clocking you press and release the switch when zero is at one point then when rotor makes full rotation you do it again.Half rotor clocking press and hold the switch, when zero is at the particular point; release it when the rotor makes half rotation. Because the switch was pressed for a longer time the system knows it is half rotor clocking therefore no additional setting is required. For each individual spin you can use full or half rotor clocking. The Acrobat can handle rotor speed range 1.5 to 16 seconds per rotation.

I f you are planning to use half rotor clocking please practice it fi rst. On the same video spins compare your predictions of ful l rotor clocking with predictions where half rotor clocking is used.

FULL OR HALF WHEEL CLOCKING

FF’s can be eas i ly upgraded. The program is reasonably compl icated so I am also reasonably confi dant nobody

wi l l t ry to dupl icate the device therefore I be l ieve I should be able to supply the code to users for eas ier upgrades.

I f you a l ready do not have Pick i t 2 programmer you can get one from eBay for around $20. Sure E lectronics se l l ing the programmer with addi t ional 5 stra ight p ins needed for programming the FF, so i f you are unsure fi rst ask me.

With programmer you can instant ly upgrade and you wi l l be a lso able to look and edi t stored bal l rotat ions data.

UPGRADES

1. S e l e c t m e n u 1 ( s e t u p )2. S e l e c t b a l l d i r e c t i o n 1 o r 2 z a p s3. C l o c k b a l l r o t a t i o n s a n d i f t h e b a l l m a ke s a d d i t i o n a l ¼ , ½ o r ¾ o f r o t a t i o n c l o c k t h a t a s w e l l . 4. Fe w s e c o n d s l a t e r t h e s y s t e m w i l l r e s p o n d w i t h 1 - 4 p u l s e s b a s e d o n w h i c h d i a m o n d t h e b a l l d r o p p e d . C h e c k

i f i t m a t c h e s r e a l b a l l d r o p . 5. N e x t t h e s y s t e m r e s p o n d s w i t h m e n u 1 - 36. S e l e c t 1 t o s a v e t h a t s p i n o r 3 t o n o t s a v e i t a n d t o c l o c k n e w s p i n .7. Re p e a t p r o c e s s 2 - 7 f o r f e w t i m e s f o r e a c h d i a m o n d y o u w a n t t o p l a y.

8. A f t e r l a s t s a v e , s e l e c t b a l l d i r e c t i o n , p r e s s a n d h o l d t h e s w i t c h t o e x i t s e t t i n g s a n d g o b a c k t o m a i n m e n u .

9. Fr o m m a i n m e n u s e l e c t a c c u r a c y 2 - 5 y o u w a n t t o p l a y. T h i s i s t r i c ky o n e . I n m y t e s t s I u s e d 3 w i t h a b o u t 3

s e t s f o r e a c h d i a m o n d I p l a y e d . Yo u c a n s e t f o r e x a m p l e a c c u r a c y 2 t o b e m o r e a c c u r a t e b u t s o m e s p i n s m a y n o t b e p r e d i c t e d . I f f o r e x a m p l e y o u s e t t h e s y s t e m o n l y o n o n e s p i n w i t h v e r y t i l t e d w h e e l y o u c a n s e t a c c u r a c y 5 . B u t e v e n t h e w h e e l h a s o n e d o m i n a n t d i a m o n d a n d s t r o n g t i l t i t i s a l w a y s g o o d t o t a ke f e w s e t s o n t h a t d i a m o n d . W i t h m o r e s e t s t h e s y s t e m w i l l p r e d i c t m o r e a c c u r a t e l y. P r e v i o u s s o f t w a r e v e r s i o n c a l c u l a t e d t h e d i ff e r e n c e s b u t t h i s o n e d o e s s a m e b u t s i n c e t h e r e i s m o r e s a m p l e s t h e r e i s l e s s t o c a l c u l a t e a n d m o r e t o k n o w.

10. A f t e r s e l e c t e d a c c u r a c y t h e s y s t e m t a ke s y o u t o t h e b a l l d i r e c t i o n m e n u 1 o r 2 . I f i n s e t t i n g s y o u s e l e c t e d 1 f o r b a l l i n C W d i r e c t i o n y o u h a v e t o s e l e c t s a m e h e r e i f n e x t s p i n t h e b a l l w i l l t r a v e l i n C W d i r e c t i o n .

11. A f t e r s e l e c t e d b a l l d i r e c t i o n c l o c k t h e r o t o r , t h e n w a i t w h e n t h e b a l l i s a t r e a s o n a b l e t i m e a n d c l o c k 2 b a l l r o t a t i o n s a s o n e . C l i c k a t s t a r t t h e n w h e n t h e b a l l m a ke s o n e r o t a t i o n d o n o t c l i c k , a n d w h e n t h e b a l l c o m p l e t e s s e c o n d r o t a t i o n c l i c k a g a i n .

S o o n a f t e r t h e s y s t e m w i l l p r e d i c t w i t h z a p o r v i b r a t i o n , a t t h a t m o m e n t y o u ’ l l n e e d t o s p o t t h e n u m b e r u n d e r t h e b a l l . I t ’ s t h e p r e d i c t i o n n u m b e r w h e r e t h e s y s t e m e x p e c t s t h e b a l l t o d r o p . I n l e s s t h e n o n e b a l l r o t a t i o n w h e n t h e b a l l m e e t s s a m e n u m b e r a g a i n t h e s y s t e m w i l l p r e d i c t a g a i n . I t w i l l n o t p r e d i c t a g a i n i n c a s e o f e r r o r o r s p e c i a l s p i n i n d i c a t o r. Yo u c a n a l s o c o n t i n u e c l o c k i n g a f t e r a d d i t i o n a l 2 b a l l r o t a t i o n s a n d t h e s y s t e m w i l l p r e d i c t a g a i n y o u c a n d o i t e v e n i f t h e s y s t e m fi r s t t i m e g a v e y o u a n e r r o r o r s p e c i a l i n d i c a t i o n .

Always use same pos i t ion for ba l l c lock ing as you used dur ing the set up process . Rotor you can c lock at any p lace and each sp in i t can be d iff erent pos i t ion .

SIMPLE START

Please do not forget!

This software version uses double rotations clocking.

It means when the ball is above the clocking diamond press and release the switch, then wait until the ball makes TWO full rotations and passes the switch again. If you want to continue with clocking to get multiple predictions or until the ball speed drops repeat the process but you always clock 2 ball rotations as one. It doesn’t eff ect systems accuracy but it reduces amount of clicks. It also gives the system time to predict two times.

DOUBLE ROTATIONS CLOCKING

The FF system under the right conditions and usage predicts where the ball will drop or it predicts a number equally distanced from the point where the ball will drop. To play eff ectively you need to know how most of the time the ball will jump then adjust predictions/off set according to it.

Please read posts about ball jump scatter at our

support forum.

BALL JUMPS SCATTER

For users who are already familiar with the FF, using Acrobat wouldn’t be a problem since its very similar.

For new users watching video for R6A program may be helpful since they can see clocking's.

http://www.youtube.com/watch?v=votBwKY8q9o

The acrobat is only diff erent because it can use more setups and CW and ACW ball direction.

First I’ll need to make one unit to beep and flash light, then I can make video about it.

VIDEO

There is a lot of information ad explanations at forum.

I am available daily for chat on MSN messenger kotlokrp@hotmail.com, if you do not use MSN we can still privately chat from forum at http://rouletteplace.com/index.php?action=pm

or http://myrulet.com/questions-and-answers.html

SUPPORT

We do not promote or advise anyone to use any methods that are illegal! Therefore, information and equipment that we supply such as device, roulette computer, to predict roulette winning numbers, are just for informational purposes only. If using it in casino especially where its classifi ed as il legal you are using it at your own risk.

The end!