t-32 series transfer casesgraphicvillage.org/meritor/pb90202.pdf · t-32 series service kits kit...

Revised 12/97

T-32 SeriesTransfer Cases

Catalog PB-90202

Strength Power Speed Agility

M E R I T O R P A R T S. R I G H T F R O M T H E S T A R T.

INTRODUCTION

• This parts book is designed so you can look up part numbers in two different ways: 1. If you know the model number of the transfer case, for example, T-32-65, you simply match the item number in the picture with the item number in the parts list. The parts list shows which part number is used on each model. 2. If you don’t know the model number, the description column in the parts list has descriptions of the different part numbers that are used on different models. • For service parts, contact Meritor Automotive at (888) 725-9355.

In Canada, (800) 668-3508. • All Meritor gears and shafts are marked with the check letter and final digits of the part

number, for example, F-5024 or X-2442. • When you service gears, we recommend you replace all mating gears for the best

quality repair. • Service kits include parts to service different models covered by this book, so the kit

may include extra parts you don’t need. In addition to kits, individual parts are available. Kits and parts can be ordered through Meritor’s Florence, KY or Brampton, Ontario distribution centers.

TABLE OF CONTENTSPage

T-32 Series Supersessions ................................................................... 2

T-32 Series Options .............................................................................. 3

T-32 Series Service Kit Reference ....................................................... 3

T-32 Series Service KitsMain Case Oil Seals................................................................ 4Main Case Shims/Bearings/Spacers....................................... 4Main Case Fasteners............................................................... 4Main Case Miscellaneous Parts.............................................. 510-1/2" x 2-1/4" FSH Brake..................................................... 5Declutch Shims/Bearings......................................................... 5Declutch Miscellaneous Parts.................................................. 510" x 1-1/2" DLM Brake........................................................... 6P.T.O. Bearings/Shims............................................................ 6P.T.O. Miscellaneous Parts..................................................... 6P.T.O. Shaft........................................................................... 6

T-32 Transfer CaseMain Case................................................................................ 7FSH Brake............................................................................... 18Declutch................................................................................... 20DLM Brake............................................................................... 22Power Take Off........................................................................ 23

Numerical Parts Index .......................................................................... 27

1

T-32 SERIES SUPERSESSIONSRELEASE REPLACES RELEASE

MODEL DATE MODEL DATET-32-42 Jul-63T-32-43 Jul-63 T-32-33 Oct-62T-32-46 Aug-63 T-32-13 Mar-51T-32-47 Aug-63T-32-57 Aug-64T-32-63 Jan-66T-32-65 May-66T-32-69 May-68T-32-70 Apr-69T-32-75 May-72T-32-78 Apr-74T-32-79 Jan-76T-32-80 Jun-81T-32-83 Jan-87T-32-84 May-88T-32-85 Jul-88T-32-86 Jul-89T-32-87 Jun-89T-32-88 Aug-90

2

T-32 SERIES OPTIONSFLANGE/YOKE

FSH DLM INPUT INPUT OUTPUT OUTPUTMODEL BRAKE BRAKE DECLUTCH P.T.O. FRONT REAR FRONT REAR

T-32-42T-32-43 10" x 1-1/2" XT-32-46 X X X XT-32-47T-32-57 10-1/2" x 2-1/4" X X XT-32-63T-32-65 10" x 1-1/2" X X X XT-32-69 X X X XT-32-70T-32-75 10" x 1-1/2" X X X XT-32-78 X X X X XT-32-79 X X XT-32-80 10" x 1-1/2" X X XT-32-83 X X X XT-32-84 10" x 1-1/2" X XT-32-85 XT-32-86 10" x 1-1/2" X X X XT-32-87 XT-32-88 X X X X X

T-32 SERIES SERVICE KITS REFERENCEKIT KIT KIT KIT KIT KIT KIT KIT KIT KIT MPS

MODEL T-32-1 T-32-2 T-32-3 T-32-4 T-32-5 T-32-6 T-32-7 T-32-8 T-32-9 T-32-10 4126T-32-42 X X X XT-32-43 X X X XT-32-46 X X X X XT-32-47 X X X XT-32-57 X X X XT-32-63 X X X XT-32-65 X X X X X XT-32-69 X X XT-32-70 X X X XT-32-75 X X X X X XT-32-78 X X X X XT-32-79 X X X XT-32-80 X X X XT-32-83 X X X X X X XT-32-84 X X X X X XT-32-85 X X X X XT-32-86 X X X X X XT-32-87 X X X X XT-32-88 X X X X X

3

T-32 SERIES SERVICE KITSKIT T-32-1 MAIN CASE OIL SEALS

PART ITEM NUMBERPART NAME NUMBER QTY. ON EXPLODED VIEW

Oil Seal-main shaft front, driven shaft front and A-1805-C-107 3 6, 77, 113driven shaft rearOil Seal Assy.-shift shaft A-1805-Z-26 1 15

KIT T-32-2 MAIN CASE SHIMS/BEARINGS/SPACERSPART ITEM NUMBER

PART NAME NUMBER QTY. ON EXPLODED VIEWShim-main shaft front (0.003") 2803-L-220 2 11Shim-main shaft front (0.005") 2803-M-221 2 11Shim-main shaft front (0.010") 2803-N-222 2 11Shim-idler shaft rear (0.003") 2803-L-220 2 100Shim-idler shaft rear (0.005") 2803-M-221 2 100Shim-idler shaft rear (0.010") 2803-N-222 2 100Shim-driven shaft rear (0.003") 2803-L-220 2 108Shim-driven shaft rear (0.005") 2803-M-221 2 108Shim-driven shaft rear (0.010") 2803-N-222 2 108Shim-idler shaft front (0.003") 2803-T-384 2 64Shim-idler shaft front (0.005") 2803-U-385 2 64Shim-idler shaft front (0.010") 2803-V-386 2 64Shim-idler shaft rear (0.010") 2203-X-336 2 95Shim-idler shaft rear (0.015") 2203-Y-337 2 95Shim-idler shaft rear (0.030") 2203-Z-338 2 95Bearing-main shaft front, main shaft rear 1828-H-138 2 12, 38Spacer-main shaft rear bearing 1844-M-455 1 39Cup-idler shaft bearing front, driven shaft 332 4 68, 82, 97, 107bearing front, idler shaft bearing rear, drivenshaft bearing rearCone-idler shaft bearing front, idler shaft 339 4 69, 96, 106bearing rear, driven shaft bearing rear

KIT T-32-3 MAIN CASE FASTENERSPART ITEM NUMBER

PART NAME NUMBER QTY. ON EXPLODED VIEWCapscrew-main shaft front cap S-2611-2 4 7Capscrew-shifter cover S-267-2 4 17Capscrew-idler shaft front cap S-267-2 3 56

S-2614-2 1Capscrew-driven shaft front cap, transfer S-268-2 22 78, 93case and coverLockwasher-main shaft rear cap and cage 1229-K-1597 6 54Lockwasher-main shaft front cap, shifter cover WA-16 48 8, 18, 54, 57, 79,main shaft rear cap and cage, idler shaft front 92, 104, 111cap, driven shaft front cap, transfer case andcover, idler shaft rear cap, driven shaft rear capNut-main shaft rear cap and cage N-16-1 6 55

4

T-32 SERIES SERVICE KITSKIT T-32-4 MAIN CASE MISCELLANEOUS PARTS


Spring-gear shift lock 2858-A-1 1 21Plunger-gear shift lock 1846-B-2 1 22Ball-gear shift lock 1898-E-57 1 23Bushing-speed driven gear 1199-M-1105 1 60Snap Ring-idler shaft bearing nut 1854-R-70 2 66, 99Silicone Gasket - 3 oz. tube 2297-Z-7098 2 10, 20, 36, 43, 63, 81, 101

KIT T-32-5 10-1/2" x 2-1/4" FSH BRAKEPART ITEM NUMBER

PART NAME NUMBER QTY. ON EXPLODED VIEWSpring-shoe retaining 1718-D-108 1 127Spring-shoe return 2758-L-12 1 128Spring Assy.-shoe hold down A-2258-Y-649 2 138Brake Shoe and Lining Assy. A3-3722-A-105 2 129

KIT T-32-6 DECLUTCH SHIMS/BEARINGSPART ITEM NUMBER

PART NAME NUMBER QTY. ON EXPLODED VIEWShim-declutch carrier cap (0.003") 2803-V-490 3 157Shim-declutch carrier cap (0.005") 2803-W-491 3 157Shim-declutch carrier cap (0.010") 2803-X-492 4 157Cup-declutch shaft bearing 14274 2 158, 162Cone-declutch shaft bearing 14137-A 2 159, 161

KIT T-32-7 DECLUTCH MISCELLANEOUS PARTSPART ITEM NUMBER

PART NAME NUMBER QTY. ON EXPLODED VIEWCotter-declutch shaft nut K-2412 1 148Oil Seal-declutch shaft A-1805-C-107 1 152Capscrew-declutch carrer cap S-2511-2 4 154Lockwasher-declutch carrier cap WA-15C 4 155Spacer-declutch shaft bearing 1844-Q-121 1 160Cotter-declutch shift shaft, declutch shift lever stud K-238 2 164, 181Oil Seal-declutch shift shaft A-1805-B-158 1 167Setscrew-declutch shift lock 3-X-161 1 169Lockwasher-declutch shift lockscrew 1229-E-421 1 170Spring-declutch shaft bearing 2858-H-86 1 171Ball-declutch shift shaft lock 1898-H-34 1 172Setscrew-declutch shift fork lock 26X-56 1 175Stud-declutch shift lever 4-X-657 1 177Lockwasher-declutch shift lever stud WA-38 1 179 Nut-declutch shift lever stud NL-28-1 1 180Silicone Gasket - 3 oz. tube 2297-Z-7098 1 156

5

T-32 SERIES SERVICE KITSKIT T-32-8 10" x 1-1/2" DLM BRAKE


Lockwire-brake anchor to case LW-1612 1 190Roller-brake 2297-L-6720 2 191Brake Shoe and Lining Assy. A6-3722-L-194 2 195Spring-brake shoe return 2258-Q-719 4 196

KIT T-32-9 P.T.O. BEARINGS/SHIMSPART ITEM NUMBER

PART NAME NUMBER QTY. ON EXPLODED VIEWShim-P.T.O. shaft cap (0.003") 2803-V-568 3 214Shim-P.T.O. shaft cap (0.005") 2803-W-569 3 214Shim-P.T.O. shaft cap (0.010") 2803-X-570 5 214Cup-P.T.O. shaft bearing 332 2 216, 221Cone-P.T.O. shaft bearing 335 2 217, 220

KIT T-32-10 P.T.O. MISCELLANEOUS PARTSPART ITEM NUMBER

PART NAME NUMBER QTY. ON EXPLODED VIEWOil Seal-P.T.O. shaft A-1805-N-352 1 209Sleeve-P.T.O. shaft oil seal 1874-A-105 1 210Cotter-shift lever stud, shift lever K-238 2 259, 270Nut-shift lever stud NL-28-1 1 260Washer-shift lever stud WA-38 1 261Stud-shift lever 4-X-657 1 262Ball-shift shaft lock 1898-H-34 1 263Spring-shift lock ball 2858-T-20 1 264Setscrew-shift shaft lock ball 3-X-161 1 265Lockwasher-shift lock screw 1229-E-421 1 266Setscrew-shift shaft and fork 26-X-56 1 267Oil Seal-shift shaft A-1805-B-158 1 269Washer-shift shaft 1829-J-244 1 271Silicone Gasket - 3 oz. tube 2297-Z-7098 1 215

MPS 4126 P.T.O. SHAFTPART ITEM NUMBER

PART NAME NUMBER QTY. ON EXPLODED VIEWShaft-P.T.O. 3297-Z-1378 1 218Nut-P.T.O. shaft end 1227-C-939 1 205

6

T-32 SERIES MAIN CASEPART

ITEM PART NAME MODEL QTY NUMBER DESCRIPTION1 Cotter-main shaft front All 1 K-2412 0.15" diameter, 1.5" long.2 Nut-main shaft front All 1 1227-L-714 1"-20, 0.5" high, 6 slots,

1.5" across flats, grade 8.3 Washer-main shaft front - 1 1229-Q-277 Not used on T-32 models in this

book.4 Flange/Yoke-main shaft front 79, 83 1 3897-B-470 1350 series, 3.53" end hub to

center cross assy., 1.38"-10 spline2" long, 4 holes 0.39" diameter.

46 1 3897-N-1002 1410 companion flange, 1.37"-10spline, 4 holes 0.44" diameter,2.63" long flange face to end hub.

57, 65, 69, 1 3897-V-386 1410 series, 3.69" long end hub to78, 80, 86, center cross assy., 1.38"-10

88 spline, 4 holes 0.39" diameter.75 1 3897-T-774 1550 series, 2.69" end hub to

center cross assy., 4 thru holes0.57" diameter, 1.37" diameter,10 spline.

5 Deflector-main shaft front - 1 3897-B-470 Not used on T-32 models in thisbook.

6 Oil Seal-main shaft front All 1 A-1805-C-107 3" O.D., 1.94" I.D., double lip, double case with spring, includedin item 9, replaces A-1805-G-59,which had optional single lip.

7 Capscrew-main shaft front cap All 4 S-2611-2 0.38"-16, 1.38" long, 0.56" acrossflats, grade 8.

8 Lockwasher-main shaft front cap All 4 WA-16 0.67" O.D., 0.32" I.D., 0.09" wide.9 Cap-main shaft front All 1 A-3866-V-672 3866-Q-1239 casting, 3.88" O.D.,

2.13" bore, 0.95" high with 4 holes0.41" diameter on 3.75" bolt circlediameter, 4 internal slots 0.38"wide, includes item 6.

10 Gasket-drive shaft front cap All - 2297-Z-7098 Silicone gasket, use as required.*11 Shim-main shaft front All 2 2803-L-220 0.003", use as required, 3.88" O.D.,

3.16" I.D., 4 holes 0.41" diameterequal spaced on 3.75" bolt circlediameter, 4 slots 0.69" wide on I.D.

2 2803-M-221 0.005", use as required, 3.88" O.D.,3.16" I.D., 4 holes 0.41" diameterequal spaced on 3.75" bolt circlediameter, 4 slots 0.69" wide on I.D.

2 2803-N-222 0.010", use as required, 3.88" O.D.,3.16" I.D., 4 holes 0.41" diameterequal spaced on 3.75" bolt circlediameter, 4 slots 0.69" wide on I.D.

12 Bearing-main shaft front All 1 1828-H-138 Ball, 3.15" O.D., 1.38" bore, 0.82" wide.

13 Shaft-main drive 42, 43, 46, 63, 1 3880-Y-935 10.94" long, 1 end threaded, 0.16"65, 70, 75, 78, diameter hole in thread end, 6T79, 80, 83, 86 spline, 1.37" O.D., 10T spline

1.36" O.D.47, 57, 69, 1 3880-Z-936 1.36" O.D., 10T spline both ends,

84, 85, 87, 88 12.81" long, 2 threaded ends withone hole 0.16" diameter drilled.

* All preformed gaskets are replaced with silicone liquid gasket at time of service.7


ITEM PART NAME MODEL QTY NUMBER DESCRIPTION14 Shaft-gear shift All 1 2843-G-7 8.22" long, 0.87" body diameter,

0.88"-18 thread, 1.44" long at oneend, 0.5" dia. hole at other end.

15 Oil Seal Assy. All 1 A-1805-Z-26 1.25" O.D., 0.88" I.D., single lip,single case, no spring, included initem 24 (E-837 and P-1056).

16 Tube-oil breather 57, 69 1 A-2847-Z-806 5.38" long. Part no longeravailable.

17 Capscrew-shifter cover All 4 S-267-2 0.38"- 16, 0.88" long, 0.56" acrossflats, grade 8.

18 Lockwasher-shifter cover All 4 WA-16 0.67" O.D., 0.32" I.D., 0.09" wide.19 Cover-gear shift 42, 43, 46, 47, 1 3855-L-12 3855-G-449 casting, same as

63, 65, 70, 75, 3855-D-420, less one hole78, 79, 80, 83, 0.38"-18 N.P.S.F., replaces 84, 85, 86, 87, 3855-U-73, has one less hole

88 0.13"- 27 N.P.S.F.57, 69 1 3855-D-420 3855-G-449 casting, 4 holes 0.41"

diameter on 3.44" x 3.75" pattern0.31" thick, 1 hole 0.38"-18 N.P.S.F.one hole 0.45" diameter.

20 Gasket-shifter cover All - 2297-Z-7098 Silicone gasket, use as required.*21 Spring-gear shift lock All 1 2858-A-1 13 coils, 1.88" free length,

0.44" O.D., 0.20" I.D.22 Plunger-gear shift lock All 1 1846-B-2 0.88" long, 0.16" diameter indent

in head to fit 0.44" diameter ball.23 Ball-gear shift lock All 1 1898-E-57 0.44" diameter ball.24 Case-transfer 42, 63, 70, 1 A-3875-L-272 3875-X-50 casting, same as

78, 79, 88 A1-3875-C-393 except has 0.75"-14tapped hole on the bottom of thecase and no 0.25"-18 tapped holenear the bottom of the case in theleft side case wall and no 0.75"-14tapped hole on the right side wallnear the bottom, includes item 37(L-168) and 2 of item 93.

83, 86 1 A2-3875-V-360 3875-X-50 casting, same asA1-3875-C-393 except no tapped holes as listed in C-393 in thecase side walls. One 0.75"-14tapped hole is at the bottom of thecase, includes item 37 (X-206 and

(Continued) X-1038) and 6 of item 93.



ITEM PART NAME MODEL QTY NUMBER DESCRIPTION24 Case-transfer (continued) 46 1 A1-3875-C-393 3875-X-50 casting, idler bearing

cage boss has four 0.38"-16 tappedholes on a 3.75" bolt circle diameterand 1 angle drilled hole near the top.Output bearing case boss has six0.38"-16 tapped holes on a 5" boltcircle diameter and 1 cored holeopen near the bottom. Left wall ofcase (looking from the outside ofthe case) has four 0.63"-11 tappedholes, 2 near the top and 2 near thebottom of the case. On the sameside there is one 0.25"-18 tappedhole near the bottom of the case.On the right side of the case thereis one 0.75"-14 tapped hole in thecase side wall near the bottom.Includes item 37 (H-268) and 2 of item 93.

43, 47, 57, 1 A3-3875-X-544 3875-X-50 casting, make from 65, 75, 80, 3875-L-272 finish by adding

84, 85 0.38"-18 tapped hole 7.68" near themiddle of the left side of the case,and 0.75"-14 tapped hole on theidler cage boss, includes items 37(H-268) and 2 of item 93.

69 1 A1-3875-E-837 3875-X-50 casting, same asA3-3875-X-544 except outputbearing cage boss has six 0.5"-13tapped holes on a 4.88" bolt circlediameter, includes items 15, 36,37 (H-268), and 91.

87 1 A1-3290-P-1056 3875-X-50 casting, same as A3-3875-X-544 except add 1 hole0.38"-24, 0.75" above idler gearcenter in right case wall, includesitems 15, 36, 37 (H-268), and 91.

25 Plug-case oil level 43, 47, 57, 65, 1 P-16 0.38"-18 N.P.T.F. male square69, 75, 80, 84, head, non-magnetic.

85, 8726 Plug-case oil line hole 86 1 P-42 0.13"-27 N.P.T.F. hex

socket-female, non-magnetic.27 Plug-cover oil line hole 86 1 P-24 0.25"- 18 N.P.T.F. female

square socket, non-magnetic.28 Bolt-shift fork clamp All 1 S-1613-2 0.38"-24, 1.62" long,

0.56" across flats, grade 8.29 Fork-gear shift All 1 2849-P-42 2849-M-13 forging, 2.31" across

jaws, 4.5" center jaws to center,0.88" x 18 hole in shifter shaft.

30 Nut-shift fork clamp All 1 NL-16-1 0.38"-24, 0.33" high,0.56" across flats, grade 8.



ITEM PART NAME MODEL QTY NUMBER DESCRIPTION31 Gear-sliding (1.87-1) 42, 43, 46, 47, 1 3892-A-2445 3892-N-637 forging, 17T, spur,

57, 63, 65, 69, 3.68" O.D. with 2.25" O.D. shift Gear-sliding (2.05-1, 2.20-1) 70, 75, 79, 80, groove and 14T internal spline.

83, 84, 85, 86, 1 3892-B-2446 3892-N-637 forging, 16T, spur,87, 88 3.48" O.D. with 2.25" O.D. shift

groove and 14T internal spline.Gear-sliding (2.60-1, 2.09-1) 78, 79 1 3892-P-4384 3892-N-637 forging, 15T, spur,

3.41" O.D. with 2.25" O.D. shift groove and 14T internal spline.

32 Washer-main drive gear thrust 42, 43, 46, 47, 1 1829-F-864 2.88" O.D., 1.58" I.D., 0.16" wide.front 57, 63, 65, 69,

70, 75, 79, 80,83, 84, 85, 86,

87, 8833 Gear-main drive (1.87-1) 42, 43, 46, 47, 1 A-3892-F-630 3892-G-3257 forging, 27T, helical,

57, 63, 65, 69, R.H., 5.22" O.D. with 17T internal70, 75, 79, 80, spline, includes item 34.

Gear-main drive (2.05-1) 83, 84, 85, 86, 1 A-3892-A-4135 3892-U-3323 forging, 27T, helical,87, 88 R.H., 5.22" O.D. with 16T internal

spline, includes item 34.Gear-main drive (2.20-1) 1 A-3892-L-1442 3892-U-3323 forging, 28T, helical,

R.H., 5.42" O.D. with 16T internalspline, includes item 34.

Gear-main drive (2.60-1) 79 1 A-3892-K-4379 3892-J-4378 forging, 29T, helical,R.H., 5.37" O.D. with 15T internalspline, includes item 34.

34 Bushing-main drive gear 42, 43, 46, 47, 1 1825-W-101 2.0" O.D., 1.57" I.D., 0.8" wide,57, 63, 65, 69, included in item 33.70, 75, 79, 80,83, 84, 85, 86,

87, 8835 Washer-main drive gear thrust All 1 1829-J-374 2.88" O.D., 1.39" I.D., 0.16"

rear wide with 1.75" diameter x 0.02"raised boss on one side.

36 Gasket-transfer case and cover All - 2297-Z-7098 Silicone gasket, use asrequired*, included initem 24 (E-837 and P-1056).

37 Cover-transfer case 42, 63, 70, 1 3876-L-168 4876-V-22 casting, 0.88" diameter 78, 79, 88 spotface, 1 hole on case/cover

mounting face below left output gearcenter, 0.75"-14 N.P.S.F., 1 holedrilled 3" right and 0.63" below idlergear center, included in item 24(L-272). Item not sold separately.

83 1 3289-X-206 4876-V-22 casting, same as3876-L-168 except add 1 hole0.25"-18 N.P.S.F. 0.63" below and2.56" left of output gear center, nospotface 0.88" diameter 1 hole oncase/cover mounting face belowleft output gear center, included initem 24 (V-360). Item not sold

(Continued) separately.



ITEM PART NAME MODEL QTY NUMBER DESCRIPTION37 Cover-transfer case (continued) 43, 46, 47, 57, 1 3876-H-268 4876-V-22 casting, same as

65, 69, 75, 80, 3876-L-168 except no 0.75"-1484, 85 ,87 N.P.S.F. hole drilled 3" right and

0.63" below idler gear center, add 1 hole 0.59" diameter 0.69" deep oncase/cover mounting flange, 3.33"radius and 0.61" below output gearcenter, included in item 24 (C-393,X-544, E-837, P-1056). Item notsold separately.

86 1 3289-X-1038 4876-V-22 casting, same as3876-L-168 except add 0.59"diameter 0.75" deep hole on 3.33"radius to left and 0.61" below outputgear center, delete 0.88" diameterspotface 1 hole on case/covermounting flange 3.33 radius and0.61" below output gear center,included in item 24 (V-360). Itemnot sold separately.

38 Bearing-main shaft rear All 1 1828-H-138 Ball, 3.15" O.D., 1.38" bore,0.82" wide.

39 Spacer-main shaft rear bearing 42, 43, 46, 63, 1 1844-M-455 1.75" O.D., 1.38" I.D., 0.91" long.70, 75, 79, 80,

83, 8840 Washer-main shaft rear bearing 42, 43, 46, 63, 1 1829-X-674 1.75" O.D., 0.41" I.D., 0.19" wide.

70, 75, 79, 80,83, 88

41 Lockwasher-main shaft rear 42, 43, 46, 63, 1 WA-16 0.67" O.D., 0.32" I.D., 0.09" wide.bearing 70, 75, 79, 80,

83, 8842 Capscrew-main shaft rear 42, 43, 46, 63, 1 S-267-2 0.38"-16, 0.88" long, 0.56" across

bearing 70, 75, 79, 80, flats, grade 8.83, 88

43 Gasket-main drive bearing cap All - 2297-Z-7098 Silicone gasket, use as required.*and cage

44 Cage-main shaft rear bearing 42, 43, 46, 63, 1 A-3826-F-162 3826-Q-355 casting, 5.13" O.D.,65, 70, 75, 79, 2.44" I.D., 1.44" high, 6 holes 0.41"

80, 86 diameter on 5" bolt circle diameterand 1 hole 0.5" diameter.

47, 57, 69, 78, 1 A-3826-T-306 3826-Q-355 casting, 5.13" O.D.,84, 85, 87, 88 2.75" I.D., 1.56" high, 6 holes 0.41"

diameter on 5" bolt circle diameter,1 hole 0.25" diameter oil slot,includes item 45.

83 1 3826-X-284 3826-X-362 casting, 6 drilled holeson 5" bolt circle diameter, 6 tappedholes on 5" bolt circle diameter,1 angle drilled hole open end.

45 Oil Seal-main shaft rear bearing 47, 57, 69, 78, 1 A-1805-C-107 3" O.D., 1.94" I.D., double lip, double84 85, 87, 88 case with spring, included in item

44 (T-306), replaces A-1805-G-59,which had optional single lip.



ITEM PART NAME MODEL QTY NUMBER DESCRIPTION46 Flange/Yoke-main drive shaft rear 69 1 3897-M-3185 1310 series, 3.72" end hub to center

cross assembly, 4 thru holes 0.33"diameter, 10 spline 1.37" diameter.Part no longer available.

78, 88 1 3897-V-386 1410 series, 3.69" long end hub tocenter cross assembly, 1.38"-10spline, 4 holes 0.39" diameter.

47 Washer-main drive shaft rear - 1 1229-Q-277 Not used on T-32 models in thisbook.

48 Nut-main drive shaft rear 47, 57 1 1227-L-714 1"-20, 0.5" high, 6 slots, 1.5" acrossflats, grade 8.

49 Cotter-main drive shaft rear 47, 57 1 K-2412 0.13" diameter, 1.5" long.50 Shim-main shaft rear - 2 2803-M-221 Not used on T-32 models in this

book.51 Cap-main shaft rear 42, 43, 46, 63, 1 3866-T-358 3866-U-1181 casting, 6 holes 0.41"

70, 75, 79, 80, diameter on 5" bolt circle diameter,86, 88 1 hole 0.13"-27 N.P.S.F.

52 Plug-main shaft rear cap 42, 43, 46, 63, 1 1850-K-89 0.13"-27 N.P.T.F. male square65, 70, 75, 79, socket head with 0.09" hole drilled

80, 83, 88 in head.53 Stud/Capscrew-main shaft rear 42, 43, 46, 63, 6 4-X-653 0.38"-24 threads, 2.13" long one

cap and cage 65, 70, 75, 79, end, 0.38"-16 threads 0.63" long 80 other end, 0.38" unthreaded body

diameter 0.5" long.47, 57, 69, 78, 6 S-2611-2 0.38"-16, 1.38" long, 0.56" across84, 85, 87, 88 flats, grade 8.

83 6 S-268-2 0.38"-16, 1" long, 0.56" across flats,grade 8.

86 6 S-2614-2 0.38"-16, 1.75" long, 0.56" acrossflats, grade 8.

54 Lockwasher-main shaft rear 83 6 1229-K-1597 0.75" O.D., 0.41" I.D., 0.09" wide.cap and cage All others 6 WA-16 0.67" O.D., 0.32" I.D., 0.09" wide.

55 Nut-main shaft rear cap and cage 42, 43, 46, 63, 6 N-16-1 0.38"-24, 0.37" high, 0.56" acrossstud 65, 70, 75, 79, flats, grade 8.

8056 Capscrew-idler shaft front cap All 3 S-267-2 0.38"-16, 0.88" long, grade 8.

1 S-2614-2 0.38"-16, 1.75" long, grade 8.57 Lockwasher-idler shaft front cap All 4 WA-16 0.67" O.D., 0.32" I.D., 0.09" wide.58 Cap-idler shaft front 42, 43, 46, 47, 1 A-3866-Z-234 3866-J-1180 casting, 3.75" O.D.,

63, 65, 70, 75, 2.81" I.D., 3.15" pilot diameter, 78, 79, 80, 83, 0.75" high, 4 holes 0.41" diameter 84, 85, 86, 87, on 4.75" bolt circle diameter on 4

88 cast bosses, 1 extra cast bossdrilled with 0.81"-20 hole 1.64" deep,includes item 60.

57, 69 1 A-3866-X-1142 3866-J-1180 casting, same asA-3866-Z-234 except add 1.5"diameter spotface on outer face,includes item 60.

59 Plug-speed hole 43, 47, 57, 65, 1 A-1850-R-18 Metal threaded plug, replaces69, 70, 78, 79, 1850-Z-104 plastic plug. Includes80 83, 84, 85, 5-X-1092 o-ring.

87, 88



ITEM PART NAME MODEL QTY NUMBER DESCRIPTION60 Bushing-speed driven gear All 1 1199-M-1105 Flanged, 0.44" flange O.D., 0.03"

flange width, 0.31" O.D., 0.25" I.D.,0.34" wide, included in item 58(Z-234 and X-1142).

61 Gear-speed driven 75 1 1898-T-670 14T, helical, R.H., 0.65" O.D.62 Sleeve-speed driven gear 75 1 1898-U-671 0.38" thru hole, 0.88"-18 male

thread one end, 0.81"-20 male thread other end, 0.88" nut.

63 Gasket-idler shaft front cap All - 2297-Z-7098 Silicone gasket, use asrequired.*

64 Shim-idler shaft front All 2 2803-T-384 0.003", use as required, 3.75" O.D.,3.16" I.D., 4 holes 0.41" diameter on3.75" bolt circle diameter, 3 slots0.13" deep on I.D.

2 2803-U-385 0.005", use as required, 3.75" O.D.,3.16" I.D., 4 holes 0.41" diameter on3.75" bolt circle diameter, 3 slots0.13" deep on I.D.

2 2803-V-386 0.010", use as required, 3.75" O.D.,3.16" I.D., 4 holes 0.41" diameter on3.75" bolt circle diameter, 3 slots0.13" deep on I.D.

65 Gear-speed driven 46 1 1898-T-696 2.19" O.D., 1.25" I.D., 0.5" wide,0.13" notch on I.D., 5 external teethon O.D.

75 1 1199-Y-1247 2.24" O.D., 1.22" I.D., 0.5" wide,1 notch on I.D., 4 external teeth onO.D.

66 Snap Ring-idler shaft bearing All 1 1854-R-70 Fits into 1.88" diameter groove,nut bent wire, 0.1" diameter.

67 Nut-idler shaft bearing front All 1 1827-E-109 1.25"-18, 2" octagonal nut, 0.61"high with 8 holes, 0.13" diameter,1.88" diameter groove on O.D. ofnut.

68 Cup-idler shaft bearing front All 1 332 3.15" O.D.69 Cone-idler shaft bearing front 42, 43, 46, 47, 1 339 1.38" bore.

57, 63, 65, 69,70, 75, 78, 79,80, 83, 84, 85,

86, 8788 1 342-S 1.69" bore.

70 Key-speed driven gear 46, 75 1 16-X-70 0.13" x 0.5" Woodruff71 Shaft-idler All 1 3880-P-250 7.66" long, 1.25"-18 thread both

ends, 1 end 0.5"-20 internal threads,2 sets of 6T splines 1.89" long.

72 Cotter-driven shaft front 42, 43, 47, 63, 1 K-2412 0.13" diameter, 1.5" long.65, 69, 70, 78,79, 80, 83, 84,85, 86, 87, 88

73 Nut-driven shaft front 42, 43, 47, 63, 1 1227-L-714 1"-20, 0.5" high, 6 slots, 1.5" across65, 69, 70, 78, flats, grade 8.79, 80, 83, 84,85, 86, 87, 88



ITEM PART NAME MODEL QTY NUMBER DESCRIPTION74 Washer-driven shaft front - 1 1229-Q-277 Not used on T-32 models in this

book.75 Flange/Yoke-driven shaft front 79, 83 1 3897-W-387 1410 companion flange, 1.37"-10

spline, 4 holes 0.44" diameter,2.56" long flange face to end hub.

46, 78, 88 1 3897-N-1002 1410 companion flange, 1.37"-10spline, 4 holes 0.44" diameter,2.63" long flange face to end hub.

65, 80, 86 1 3897-V-386 1410 series, 3.69" long endhub to center cross assembly,1.38"-10T spline, 4 holes0.39" diameter.

75 1 3897-T-774 1550 series, 2.69" end hub to centercross assembly, 4 thru holes 0.57"diameter, 1.37"-10 spline.

76 Deflector-driven shaft front - 1 2847-Z-312 Not used on T-32 models in thisbook.

77 Oil Seal-driven shaft front 42, 43, 47, 63, 1 A-1805-C-107 3" O.D., 1.94" I.D., double lip, double65, 70, 79, 80, case with spring, included in item

83 80. Replaces A-1805-G-59, whichhad optional single lip.

78 Capscrew-driven shaft front cap 42, 43, 46, 47, 6 S-268-2 0.38"-16, 1" long, 0.56" across63, 65, 70, 75, flats, grade 8.78, 79, 80, 83,84, 85, 86, 87,

8879 Lockwasher-driven shaft front 42, 43, 46, 47, 6 WA-16 0.67" O.D., 0.32" I.D., 0.09" wide.

cap 63, 65, 70, 75,78, 79, 80, 83,84, 85, 86, 87,

8880 Cap-driven shaft front bearing 42, 43, 47, 63, 1 A-3866-M-299 4.75" O.D., 2" I.D., 1.04" high, six

65, 70, 79, 80, holes on bosses, 0.41" diameter on83 5" bolt circle diameter on cast

bosses, 1 internal cast slot 0.38"wide, includes item 77.

81 Gasket-driven shaft front cap All - 2297-Z-7098 Silicone gasket, use as required.*82 Cup-driven shaft bearing front All 1 332 3.15" O.D.83 Cone-driven shaft bearing front 42, 43, 47, 57, 1 339 1.38" bore.

63, 65, 69, 70,79, 80, 83, 8846, 75, 78, 84, 1 342-S 1.69" bore.

85, 86, 8784 Shaft-driven 42, 47, 63, 70, 1 3880-D-264 11.25" long, both ends threaded

79, 83 with 0.16" diameter hole in threads1.37"-10 splines on both ends.

46, 78, 85, 87, 1 3880-Q-251 9.56" long, 1 end threaded with88 0.16" diameter hole in thread, 16T

spline one end, 6T spline other end.75, 84, 86 1 3880-Z-702 10.83" long, 1 end threaded and

0.16" diameter hole in thread end,16T spline one end, 6T spline other

(Continued) end.



ITEM PART NAME MODEL QTY NUMBER DESCRIPTION84 Shaft-driven (continued) 43, 65, 80 1 3880-F-838 12.52" long, both ends threaded

with 0.16" diameter hole in threads,1.36"-10 spline both ends.

57, 69 1 3880-L-948 12.97" long, both ends threadedwith 0.16" diameter hole in threads,1.36"-10 spline both ends.

85 Plug-case drain 42, 43, 46, 47, 1 P-112 Male, square head, 57, 63, 65, 69, 0.75"-14 N.P.T.F. non-magnetic.70, 75, 78, 79,80, 83, 84, 85,

87, 8886 1 1850-T-150 Female, square socket,

0.75"-14 N.P.T.F. magnetic.86 Name Plate 86 1 2297-Y-4835 3" long, 1.25" high, 0.02" wide

with 2 holes 0.15" diameter.87 Screw-name plate 86 1 9-X-16 0.25" long, 0.14" diameter.88 Gear-low speed (1.87-1) 42, 43, 46, 47, 1 3892-A-521 3892-H-128 forging, 33T, spur, 6.88"

57, 63, 65, 69, O.D., 6T internal spline (tapered).Gear-low speed (2.05-1, 2.20-1) 70, 75, 79, 80, 1 3892-T-618 3892-H-138 forging, 34T, spur,

83, 84, 85, 86, 7.08" O.D., 6T internal spline87, 88 (tapered).

Gear-low speed (2.60-1, 2.09-1) 78, 79 1 3892-N-4382 3892-Z-2704 forging, 35T, spur,7.21" O.D., 6T internal spline(tapered).

89 Gear-driven (1.87-1, 2.05-1) 42, 43, 46, 47, 1 3892-Z-520 3892-Y-675 forging, 27T, helical,57, 63, 65, 69, R.H., 5.22" O.D., 6T internal spline70, 75, 79, 80, (tapered).

Gear-driven ( 2.20-1) 83, 84, 85, 86, 1 3892-N-1444 3892-Y-675 forging, 28T, helical,87, 88 R.H., 5.42" O.D., 6T internal spline

(tapered).Gear-driven (2.60-1, 2.09-1) 78, 79 1 3892-L-4380 3892-Y-675 forging, 29T, helical,

R.H., 5.37" O.D., 6T internal spline(tapered).

90 Gear-idler (1.87-1, 2.05-1) 42, 43, 46, 47, 1 3892-Y-519 3892-Y-675 forging, 28T, helical,57, 63, 65, 69, L.H., 5.42" O.D., 6T internal spline

70, 75, 79, 80, (tapered).Gear-idler ( 2.20-1) 83, 84, 85, 86, 1 3892-M-1443 3892-Y-675 forging, 27T, helical,

87, 88 L.H., 5.42" O.D., 6T internal spline(tapered).

Gear-idler (2.60-1, 2.09-1) 78, 79 1 3892-M-4381 3892-Y-675 forging, 26T, helical,L.H., 5.16" O.D., 6T internal spline(tapered).

91 Dowel-cover to case All 2 1846-M-351 1.25" long, 0.41"/0.38" taperdiameters, included in item 24(E-837 and P-1056).

92 Lockwasher All 16 WA-16 0.67" O.D., 0.32" I.D., 0.09" wide.93 Capscrew-transfer case and All 16 S-268-2 0.38"-16, 1" long, 0.56" across

cover flats, grade 8.94 Plug-oil level 42, 47, 57, 63, 1 P-112 Male, square head

69, 70, 78, 79, 0.75"-14 N.P.T.F., non-magnetic.83, 86, 88

46 1 P-14 Male, square head 0.25"-14 N.P.T.F., non-magnetic.



ITEM PART NAME MODEL QTY NUMBER DESCRIPTION95 Shim-idler shaft rear All 2 2203-X-336 0.010", use as required,

1.88" O.D., 1.38" I.D.2 2203-Y-337 0.015", use as required,

1.88" O.D., 1.38" I.D.2 2203-Z-338 0.030", use as required,

1.88" O.D., 1.38" I.D.96 Cone-idler shaft bearing rear All 1 339 1.38" bore.97 Cup-idler shaft bearing rear All 1 332 3.15" O.D.98 Nut-idler shaft bearing rear All 1 1827-E-109 1.25"-18, 2" octagonal nut, 0.61"

high with 8 holes, 0.13" diameter,1.88" diameter groove on O.D. ofnut.

99 Snap Ring-idler shaft bearing All 1 1854-R-70 Fits into 1.88" diameter groove,nut bent wire, 0.1" diameter.

100 Shim-idler shaft rear All 2 2803-L-220 0.003", use as required, 3.88" O.D.,3.16" I.D., 4 holes 0.41" diameterequal spaced on 3.75" bolt circlediameter, 4 slots 0.69" wide on I.D.



101 Gasket-idler shaft rear cap All - 2297-Z-7098 Silicone gasket, use as required.*102 Cap-idler shaft rear 42, 43, 46, 47, 1 3866-B-392 Same as 3866-A-235 except add

63, 65, 70, 75, one hole 0.13"-27. Replaces78, 79, 80, 83, 3855-A-235.84, 85, 86 87,

8857, 69 1 3866-A-235 3866-C-1173 casting, 3.15" O.D.

pilot diameter, 4 holes 0.41"diameter on 3.75" bolt circle dia.,4 equal spaced notches on I.D.Replaced by 3866-B-392. Partno longer available.

103 Breather 42, 43, 46, 47, 1 A-1199-C-1043 1.06" long with 0.13"-27 N.P.S.F.63, 65, 70 75,78 79, 80, 83,84, 85, 86, 87,

8857, 69 1 A-1199-P-1394 1.5" long with 0.38" pipe thread,

included in item 16.104 Lockwasher-idler shaft rear cap All 4 WA-16 0.67" O.D., 0.32" I.D., 0.09" wide.105 Capscrew-idler shaft rear cap 42, 46, 63, 70, 4 S-268-2 0.38"-16, 1" long, 0.56" across

78, 79, 83, 88 flats, grade 8.86 4 S-267-2 0.38" -16, 0.88" long, 0.56" across

flats, grade 8.43, 47, 57, 65, 4 S-269-2 0.38"-16, 1.12" long, 0.56" across69, 75, 80, 84, flats, grade 8.

85, 87



ITEM PART NAME MODEL QTY NUMBER DESCRIPTION106 Cone-driven shaft bearing rear All 1 339 1.38" bore.107 Cup-driven shaft bearing rear All 1 332 3.15" O.D.108 Shim-driven shaft rear All 2 2803-L-220 0.003", use as required, 3.88" O.D.,

3.16" I.D., 4 holes 0.41" diameterequal spaced on 3.75" bolt circlediameter, 4 slots 0.69" wide on I.D.



109 Gasket-driven shaft rear cap All - 2297-Z-7098 Silicone gasket, use as required.*110 Cap-driven shaft bearing rear 42, 47, 57, 63, 1 A-3866-V-672 3866-Q-1239 casting, 3.88" O.D.,

69, 70, 78, 79, 2.13" bore, 0.95" high with 4 holes83, 85, 87, 88 0.41" diameter on 3.75" bolt circle

diameter, 4 internal slots 0.38"wide, includes item 113.

111 Lockwasher-driven shaft rear 42, 46, 47, 57, 4 WA-16 0.67" O.D., 0.32" I.D., 0.09" wide.cap 63, 69, 70, 78,

79, 83, 85, 87,88

112 Capscrew-driven shaft rear cap 42, 63, 70, 78, 4 S-2611-2 0.38"-16, 1.38" long, 0.56" across79, 83, 85, 87, flats, grade 8.

8846 4 S-2612-2 0.38"-16, 1.5" long, 0.56" across

flats, grade 8.47, 57, 69 4 S-2613-2 0.38"-16, 1.62" long, 0.56" across

flats, grade 8.113 Oil Seal-driven shaft rear 42, 46, 47, 57, 1 A-1805-C-107 3" O.D., 1.94" I.D., double lip,

63, 69, 70, 78, double case with spring, included79, 83, 85, 87, in item 110. Replaces A-1805-G-59

88 which had optional single lip.114 Deflector-driven shaft rear - 1 2847-Z-312 Not used on T-32 models in this

book.115 Flange/Yoke-driven shaft rear 79, 83 1 3897-B-470 1350 series, 3.53" end hub to center

cross assembly, 1.38"-10 spline,2" long, 4 holes 0.39" diameter.

43, 46, 80, 1 3897-N-1002 1410 companion flange, 1.37"-1084, 86 spline, 4 holes 0.44" diameter,

2.63" long flange face to end hub.. 57, 65, 69, 1 3897-V-386 1410 series, 3.69" long end hub to

78, 88 center cross assembly, 1.38"-10spline, 4 holes 0.39" diameter.

75 1 3897-T-774 1500 series, 2.69" end hub to centercross assembly, 4 thru holes 0.51"diameter 1.37"-10 spline.

116 Washer-driven shaft rear - 1 1229-Q-277 Not used on T-32 models in thisbook.

117 Nut-driven shaft rear All 1 1227-L-714 1"-29, 0.5" high, 6 slots, 1.5" acrossflats, grade 8.

118 Cotter-driven shaft rear All 1 K-2412 0.13" diameter, 1.5" long.


T-32 SERIES FSH BRAKESPART

ITEM PART NAME MODEL QTY NUMBER DESCRIPTION119 Cotter-brake locknut 57, 69 1 K-2412 0.13" diameter, 1.5" long.120 Locknut-brake 57, 69 1 1227-L-714 1"-20, 0.5" high, 6 slots, 1.5" across

flats, grade 8.121 Washer-brake - 1 1229-Q-277 Not used on T-32 models in this

book.122 Nut-brake drum 57, 69 4 N-17-1 0.44"-20, 0.42" high, 0.68" across

flats, grade 8, included in item 125.123 Lockwasher-brake drum bolt 57 4 WA-17 0.77" O.D., 0.46" I.D., 0.11" wide,

included in item 125.124 Flange/Yoke-brake 57, 69 1 3897-N-1002 1410 companion flange, 1.37"-10

spline, 4 holes 0.44" diameter, 2.63"long flange face to end hub,included in item 125.

125 Drum-brake 57 1 A-3819-E-421 3819-D-420 casting, includes items122, 123, 124, and 126. Assemblymust be balanced.

126 Bolt-brake drum 57, 69 4 10-X-645 0.44"-20, 1.5" long, 0.63" diameterhead, 0.44" long, 30 serrations onbolt body, grade 8, included initem 125.

127 Spring-shoe retaining 57 1 1718-D-108 5.55" overall length, 0.12" diameterwire, both ends have 0.38" hookprofile.

128 Spring-shoe return 57 1 2758-L-12 Free length 6.46", 1 set of coilseach end with straight wire 3.5",minimum length 12 total active coils,color red, wire diameter 0.12",0.88" O.D.

129 Brake Shoe and Lining Assy. 57 2 A3-3722-A-105 Non-asbestos. ReplacesA2-3722-A-105 asbestos. Uselining kit 2000-Z-1456 for service.

130 Rod-wheel cylinder push 57 2 1745-M-13 1.94" long, 0.44" diameter with0.38" x 0.31" notch one end.

131 Cylinder Assy.-wheel 57 1 A6-3761-D-4 Cylinder assembly marked withgreen paint, 1.38" diameter cylinder assembly with filler plug.

132 Spacer-wheel cylinder 57 1 1744-D-4 2.5" x 2.13", 0.13" wide, 1 hole centered with 1.52" diameter and4 mounting holes 0.33" diameter.

133 Lockwasher 57 3 WA-15C 0.32" I.D., 0.82" O.D., 0.08" wide.134 Capscrew 57 3 S-256P-2 0.31"-18, 0.75" long, 0.49" across

flats, grade 8.135 Capscrew-brake to case 57 6 S-277-2 0.44"-14, 0.88" long, 0.62" across

flats, grade 8.136 Lockwasher-brake to case 57 6 WA-17 0.77" O.D., 0.46" I.D., 0.11" wide.

capscrew137 Plate Assy.-backing 57 1 A-3736-W-647 0.18" wide stamping, 4.5" I.D. pilot

diameter, 6 holes 0.47" diameter on 5.25" bolt circle diameter and2 holes 0.52" diameter.

138 Spring Assy.-shoe hold down 57 2 A-2258-Y-649 Free length spring 1.42", 7.75 totalcoils, 0.07" wire dia., 0.58" O.D.

139 Rod-anti-rattle retainer 57 1 1779-Q-147 2.25" long, 0.13" diameter, 0.38"diameter head.


T-32 SERIES FSH BRAKESPART

ITEM PART NAME MODEL QTY NUMBER DESCRIPTION140 Oil Dam-brake anchor 57 1 1829-T-306 3.31" O.D., 0.38" high, 0.07" wide,

oval hole 1.44"/1.16" diameter,included in item 145.

141 Spacer-driven shaft front 57, 69 1 1844-J-660 1.94" O.D., 1.37" I.D., 1.78" long,chamfer both ends.

142 O-Ring-driven shaft sleeve 57, 69 1 5-X-729 1.38" O.D., 0.06" wide, includedin item 144 (X-336). Part nolonger available.

143 Oil Seal-driven shaft front 57, 69 1 A-1805-C-107 3" O.D., 1.94" I.D., double lip, double case with spring, includedin item 144 (X-336 and Y-3145).Replaces A-1805-G-59 which hadoptional single lip.

144 Cap-brake anchor and bearing 57 1 A-3911-X-336 3911-W-335 casting, 5.75" O.D.,2.13" I.D., 2.29" high, 0.44"-14, sixholes on 5.25" bolt circle diameter,6 holes 0.41" diameter on 5" boltcircle diameter, includes items 142and 143. Part no longer available.

Adapter-brake 69 1 A-3897-Y-3145 10.56" long, 7.62" wide, has 5.75"O.D. boss with 2.12" diameter hole,6 holes 0.53" diameter on 4.88" boltcircle diameter and 4 offset holes0.53" diameter at opposite ends ofthe adapter, includes item 143.

145 Stud-brake anchor and bearing 57 6 4-X-769 0.44"-20/0.44"-14, 3.56" long.cap Part no longer available.Capscrew-brake adapter to 69 6 S-2816-2 0.5"-13, 2" long, 0.74" across flats,case grade 8.

146 Nut-brake anchor and bearing 57 6 N-16-1 0.38"-24, 0.37" high, 0.56" acrosscap stud flats, grade 8.

147 Lockwasher-brake adapter to 69 6 WA-18 0.86" O.D., 0.52" I.D., 0.13" wide.case


T-32 SERIES DECLUTCHPART

ITEM PART NAME MODEL QTY NUMBER DESCRIPTION148 Cotter-declutch shaft nut 46, 75, 78, 84, 1 K-2412 0.13" diameter, 1.5" long.

85, 86, 87, 88149 Nut-declutch shaft 46, 75, 78, 84, 1 1227-L-714 1"-20, 1.5" across flats, slotted nut,

85, 86, 87, 88 grade 8.150 Flange/Yoke-declutch - 1 3280-C-1979 Not used on T-32 models in this

book.151 Deflector-declutch - 1 2847-Z-312 Not used on T-32 models in this

book.152 Oil Seal-declutch shaft 46, 75, 78, 84, 1 A-1805-C-107 3" O.D., 1.94" I.D., double lip, double

85, 86, 87, 88 case with spring, included in item153, replaces A-1805-G-59 whichhad optional single lip.

153 Cap-declutch carrier bearing 46, 75, 78, 84, 1 A-3866-G-293 3866-K-1181 casting, 4" O.D. with85, 86, 87, 88 1 external flat, 0.88" high, 4 holes

0.34" diameter on 3.75" bolt circlediameter, includes item 152.

154 Capscrew-declutch carrier cap 46, 75, 78, 84, 4 S-2511-2 0.31"-18, 1.38" long, 0.49" across85, 86, 87, 88 hex flats, grade 8.

155 Lockwasher-declutch carrier 46, 75, 78, 84, 4 WA-15C 0.58" O.D., 0.33" I.D., 0.08" wide.cap 85, 86, 87, 88

156 Gasket-declutch carrier cap 46, 75, 78, 84, - 2297-Z-7098 Silicone gasket, use as required.*85, 86, 87, 88

157 Shim-declutch carrier cap 46, 75, 78, 84, 3 2803-V-490 0.003", use as required, 4" O.D.,85, 86, 87, 88 3" I.D., 1 flat on O.D., 4 holes 0.34"

diameter on 3.75" bolt circlediameter and 1 hole 0.38" diameter1.75" from center.

3 2803-W-491 0.005", use as required, 4" O.D.,3" I.D., 1 flat on O.D., 4 holes 0.34"diameter on 3.75" bolt circlediameter and 1 hole 0.38" diameter1.75" from center.

4 2803-X-492 0.010", use as required, 4" O.D.,3" I.D., 1 flat on O.D., 4 holes 0.34"diameter on 3.75" bolt circlediameter and 1 hole 0.38" diameter1.75" from center.

158 Cup-declutch shaft bearing 46, 75, 78, 84, 1 14274 2.72" O.D.85, 86, 87, 88

159 Cone-declutch shaft bearing 46, 75, 78, 84, 1 14137-A 1.38" bore.85, 86, 87, 88

160 Spacer-declutch shaft bearing 46, 75, 78, 84, 1 1844-Q-121 1.63" O.D., 1.39" I.D., 0.72" wide.85, 86, 87, 88

161 Cone-declutch shaft bearing 46, 75, 78, 84, 1 14137-A 1.38" bore.85, 86, 87, 88

162 Cup-declutch shaft bearing 46, 75, 78, 84, 1 14274 2.72" O.D., included in item 168.85, 86, 87, 88

163 Shaft-declutch 46, 75, 78, 84, 1 3880-R-252 3 spline shaft 6.81" long, 2 splines85, 86, 87, 88 1.68" -16, 1.88" long, 1 spline

1.36"-10, 2.06" long.164 Cotter-declutch shift shaft 46, 75, 78, 84, 1 K-238 0.09" wide, 1" long.

85, 86, 87, 88165 Lockwasher-declutch shift shaft 46, 75, 78, 84, 1 1829-J-244 0.94" O.D., 0.58" I.D., 0.03" wide.

85, 86, 87, 88


T-32 SERIES DECLUTCHPART

ITEM PART NAME MODEL QTY NUMBER DESCRIPTION166 Shaft-declutch shift 46, 75, 78, 84, 1 2843-D-108 4.94" long, 0.56" diameter, 4.38"

85, 86, 87, 88 straight shaft, 1.53" right angle leg.167 Oil Seal-declutch shift shaft 46, 75, 78, 84, 1 A-1805-B-158 0.81" O.D., 0.56" I.D., 0.12" wide,

85, 86, 87, 88 vulcanized rubber in metal retainer.168 Carrier-declutch shaft bearing 46, 75, 78, 84, 1 A-3826-H-164 3826-N-352 casting, 4.94" long with

85, 86, 87, 88 6 holes 0.41" diameter on 5" boltcircle diameter, 4 holes 0.31"-18on 3.75" bolt circle diameter,includes items 162 and 177.

169 Setscrew-declutch shift lock 46, 75, 78, 84, 1 3-X-161 0.38"-16, 0.31" long.85, 86, 87, 88

170 Lockwasher-declutch shift 46, 75, 78, 84, 1 1229-E-421 Internal tooth type, 0.69" O.D.,lockscrew 85, 86, 87, 88 0.04" wide.

171 Spring-declutch shaft bearing 46, 75, 78, 84, 1 2858-H-86 0.53" free length, 0.28" O.D.,85, 86, 87, 88 number of coils optional.

172 Ball-declutch shift shaft lock 46, 75, 78, 84, 1 1898-H-34 0.31" diameter.85, 86, 87, 88

173 Plug-declutch carrier 46, 75, 78, 84, 1 1850-Q-43 0.75"-14, male square head with85, 86, 87, 88 0.13" diameter drill hole in head.

174 Fork-declutch shift 46, 75, 78, 84, 1 2849-Y-77 0.31"-24 thread setscrew hole85, 86, 87, 88 to hold shift rail, 2.06" long center,

0.53" diameter shift railhole to end fork tangs.

175 Setscrew-declutch shift fork 46, 75, 78, 84, 1 26-X-56 0.31"-24 thread, 0.53" long.lock 85, 86, 87, 88

176 Clutch-declutch sliding 46, 75, 78, 84, 1 2848-R-70 2.69" O.D., 1.75" long, 16 internal85, 86, 87, 88 teeth, 1.71" I.D. with 0.13" wide shift

fork groove. Part no longer available.177 Stud-declutch shift lever 46, 75, 78, 84, 1 4-X-657 0.5"-13/ 0.5"-20, 1.63" long, 0.13"

85, 86, 87, 88 drilled hole in 0.5"-20 thread, included in item 168, for on-highwayapplication. For off-highway use4-X-1521.

178 Lever-declutch shift 46, 75, 78, 84, 1 2847-T-254 5.63" long, 0.25" thick, 1" wide with85, 86, 87, 88 1 hole each end 0.52" diameter,

1 slot 0.83" x 0.57".179 Lockwasher-declutch shift lever 46, 75, 78, 84, 1 WA-38 1.06" O.D., 0.53" I.D., 0.09" wide.

stud 85, 86, 87, 88180 Nut-declutch shift lever stud 46, 75, 78, 84, 1 NL-28-1 0.5"-20, 0.44" high, 6 slots, 0.75"

85, 86, 87, 88 across slots, grade 8.181 Cotter-declutch shift lever stud 46, 75, 78, 84, 1 K-238 0.09" wide, 1" long.

85, 86, 87, 88


T-32 SERIES DLM BRAKESPART

ITEM PART NAME MODEL QTY NUMBER DESCRIPTION182 Dowel-brake anchor to case 43, 65, 75, 80, 1 1846-L-246 1.88" long, 0.62" diameter,

84, 86 included in item 183.183 Brake-anchor 43, 65, 75, 80, 1 A-3911-M-325 3911-K-323 casting, 3.88" bolt circle

84, 86 dia., 1 hole 0.62" dia. on 3.4" radiusfrom bore, 5" O.D., 2.06" dia. borewith 4 holes on 3.75" bolt circle dia.,1 hole 0.5" dia., includes items182 and 185.

184 Oil Seal-driven shaft rear 43, 65, 75, 80, 1 A-1805-W-335 2.88" O.D., 1.94" I.D., double lip,84, 86 double case with spring.

185 Dowel-brake to brake anchor 43, 65, 75, 80, 1 1846-Y-103 0.75" long, 0.5" diameter, included84, 86 in item 183.

186 Spacer-driven shaft bearing rear 43, 65, 75, 80, 1 1844-H-476 1.94" O.D., 1.38" I.D., 1.31" long,84, 86 chamfer both ends. Part no longer

available.187 Backing Plate Assy. 43, 65, 75, 80, 1 A1-3736-V-126 3.13" dia. pilot, 4 holes 0.41" dia. on

84, 86 3.75" bolt circle dia. and 1 hole 0.51"dia. on 3.87" bolt circle dia.,includes brackets.

188 Lockwasher-brake anchor to case 43, 65, 75, 80, 4 WA-16 0.67" O.D., 0.32" I.D., 0.09" wide.84, 86

189 Capscrew-brake anchor to case 43, 65, 75, 80, 4 S-2621-D2 0.38"-16, 2.62" long, 0.56" across84, 86 flats, with one hole drilled in head,

grade 8.190 Lockwire-brake anchor to case 43, 65, 75, 80, 1 LW-1612 16 gage, 12" long.

84, 86191 Roller-brake 43, 65, 75, 80, 2 2297-L-6720 1" O.D., 0.56" I.D., 0.25" wide.

84, 86 Replaces 1779-J-88.192 Lever-brake 43, 65, 75, 80, 1 2247-D-1252 3.5" punch dia. to 0.45" dia. hole,

84, 86 1 additional 0.56" dia. hole 3.4" from3.5" punch dia. Replaces 372-G-85.

193 Rivet-lining to shoe 43, 65, 75, 80, 20 RV-354 Rivets available separately or84, 86 included in items 194 and 195.

194 Lining Kit-brake shoe 43, 65, 75, 80, 1 2000-S-1397 Kit includes lining and rivets,84, 86 included in item 195.

195 Brake Shoe and Lining Assy. 43, 65, 75, 80, 2 A6-3722-L-194 Includes items 193 and 194.84, 86

196 Spring-brake shoe return 43, 65, 75, 80, 4 2258-Q-719 Tension spring, 0.5" O.D., 17 coils,84, 86 2.09" free length.

197 Bolt-brake drum 43, 65, 75, 80, 4 10-X-645 0.44"-20, 1.5" long, 0.63" diameter84, 86 head, 0.44" long, 30 serrations on

bolt body, grade 8.198 Drum-brake 43, 65, 75, 80, 1 3719-D-56 Stamped brake drum with 3" pilot,

84, 86 4 holes 0.44" diameter on 3.75"bolt circle diameter.

199 Flange/Yoke-brake - 1 3897-N-1002 Not used on T-32 models in this200 Spacer-flange to brake drum - 4 1844-H-476 book.201 Nut-brake drum bolt 43, 65, 75, 80, 4 N-17-1 0.44"-20, 0.42" high, 0.68" across

84, 86 flats, grade 8.202 Washer-brake - 1 1229-Q-277 Not used on T-32 models in this203 Cotter-brake locknut - 1 K-2412 book.204 Locknut-brake - 1 1227-B-496


T-32 SERIES POWER TAKE OFFPART

ITEM PART NAME MODEL QTY NUMBER DESCRIPTION205 Nut-P.T.O. shaft end 65 1 1227-L-714 1"-20, 0.5" high, 6 slots, 1.5" across

flats, grade 8.83 1 1227-C-939 1"-20, 1.3" across flats grade 8,

included in item 218 (MPS 4126)206 Cotter-P.T.O. shaft nut 65, 83 1 K-2412 0.13" diameter, 1.5" long.207 Washer-P.T.O. shaft nut - 1 1229-E-1331 Not used on T-32 models in this

book.208 Flange/Yoke-input - 1 3897-N-1002 Not used on T-32 models in this

book.209 Oil Seal-P.T.O. shaft 65, 83 1 A-1805-N-352 2.44" O.D., 1.69" I.D., single case,

double lip with spring, included in item 211.

210 Sleeve-P.T.O. shaft oil seal 65, 83 1 1874-A-105 1.69" O.D., 1.38" I.D., 0.94" wide.211 Cap-P.T.O. shaft bearing 65, 83 1 A-3866-S-357 3866-T-1199 casting, 4 holes on

3.75" bolt circle diameter, 3.15"pilot, included in item 209.

212 Capscrew-P.T.O. shaft cap 65, 83 4 S-256P-2 0.31"-18, 0.75" long,0.49" across flats, grade 8.

213 Washer-P.T.O. shaft cap 65 4 WA-15C 0.58" O.D., 0.33" I.D., 0.08" wide.83 4 1229-E-1669 0.62" O.D., 0.34" I.D., 0.06" wide.

214 Shim-P.T.O. shaft cap 65, 83 3 2803-V-568 0.003", use as required, 4" O.D.,3.16" I.D., 4 holes 0.34" diameter on3.75" bolt circle diameter, 1 notch on I.D. 0.63" wide.

3 2803-W-569 0.005", use as required, 4" O.D.,3.16" I.D., 4 holes 0.34" diameter on3.75" bolt circle diameter, 1 notch on I.D. 0.63" wide.

5 2803-X-570 0.010", use as required, 4" O.D.,3.16" I.D., 4 holes 0.34" diameter on3.75" bolt circle diameter, 1 notch on I.D. 0.63" wide.

215 Gasket-P.T.O. shaft cap 65, 83 - 2297-Z-7098 Silicone gasket, use as required.*216 Cup-P.T.O. shaft bearing 65, 83 1 332 3.15" O.D.217 Cone-P.T.O. shaft bearing 65, 83 1 335 1.38" bore.218 Shaft-P.T.O. 65 1 3880-K-713 2 spline shaft 9.06" long, 10T spline

one end with 1.37" O.D., 6T splineother end with 1.36" O.D., one endhas 1"-20 thread, includes 1.63"1.63" diameter, 1.94" long journal.

83 1 MPS 4126 Same as 3880-K-713 except 1.63"diameter journal now has 1.69"eccentric lobe, includes item 205(C-939). Replaces 3880-P-822.

219 Key-tapered P.T.O. shaft - 1 16-X-40 Not used on T-32 models in thisbook.

220 Cone-P.T.O. shaft bearing 65, 83 1 335 1.38" bore.221 Cup-P.T.O. shaft bearing 65, 83 1 332 3.15" O.D., included in items 222.222 Carrier-P.T.O. shaft bearing 65 1 A-3826-G-163 3826-R-356 casting, no boss cast

at bottom 5.06" diameter, 3.75" boltcircle has 4 holes 0.31"-18,0.13"-27 N.P.S.F. hole 1.38" from5.06" diameter end, includes items

(Continued) 221 and 262.



ITEM PART NAME MODEL QTY NUMBER DESCRIPTION222 Carrier-P.T.O. shaft bearing 83 1 A-3826-Y-285 3826-D-394 casting, integral boss

(continued) cast at bottom 5.06" diameter with0.88" diameter cored hole in bossbottom, has 8 holes on 5" bolt circlediameter, 0.31"-18 and 0.63"diameter hole in casting, includesitems 221, 253, 262 and 269.

223 Plunger-oil pump 83 1 1846-V-126 1.84" long, 0.75" diameter,2 grooves 0.13" wide on O.D.,included in item 226.

224 Spring-oil pump plunger 83 1 2858-W-101 11.2 coils, 1.75" long, 0.38" I.D.,included in item 226.

225 Gasket-oil pump to carrier 83 - 2297-Z-7098 Silicone gasket, use as required.*226 Oil Pump-body assy. 83 1 A2-2847-Q-303 Includes items 223, 224, 227, 228,

233, 241, 242, and 243.227 Spring-check valve 83 1 2858-X-102 3 coils, 0.48" long, 0.41" O.D.,

0.27" I.D., included in item 226.228 Ball-pump inlet check valve 83 1 1898-Q-251 0.34" dia. included in item 226.229 Fitting-intake tube to case 83 1 1898-J-868 1.02" long, 0.63"-18 female thread,

0.25"-18 N.P.T.F. male thread,0.28" hole, 0.75" across flats.

230 Elbow-oil intake tube to adapter 83 1 A-1898-W-595 90 degree elbow, 1" long with male0.25" N.P.T.F. by 1.28" long with nutfor 0.38" diameter tube.

231 Tube-oil pump intake 83 1 A-2847-R-304 0.38" diameter copper tube 9.75"long, 3.75" long bend, developedlength 12.81", includes item 232.

232 Nut-pump intake tube to case 83 1 1898-G-241 0.66" long, 0.63"-18 male thread,0.63" across flats, included initem 231.

233 Adapter-oil pump to intake elbow 83 1 1898-H-866 0.5"-20 male thread, 0.25" N.P.T.F.female thread 1.19" long, 0.28"diameter hole, included in item 226.

234 Capscrew-oil pump to case 83 4 S-256P-2 0.31"-18, 0.75" long, 0.49" acrossflats, grade 8.

235 Washer-oil pump capscrew 83 4 1229-E-1669 0.62" O.D., 0.34" I.D., 0.06" wide.236 Tube-oil pump outlet 83 1 A-2847-U-541 0.25" diameter copper tube,

includes items 237 and 244.237 Nut-oil pump outlet tube 83 1 1898-J-504 0.59" long, 0.44"-24 male thread,

0.25" hole, 0.44" across flats,included in item 236.

238 Elbow-oil pump outlet tube to case 83 1 1898-L-532 0.13" male pipe thread, 0.91" long,0.53" with 0.44"- 24 female threadfor 0.25" dia. tube, female threadend is 0.53" square.

239 Capscrew-carrier to bearing cage 83 6 S-269-2 0.38"-16, 1.12" long, 0.56" acrossflats, grade 8.

240 Washer-carrier to bearing cage 83 6 1229-K-1597 0.75" O.D., 0.41" I.D., 0.09" wide.241 Ball-pump outlet check valve 83 1 1228-K-37 0.37" dia., included in item 226.242 Spring-check valve 83 1 2858-X-102 3 coils 0.48" long, 0.41" O.D.,

0.27" I.D., included in item 226.243 Fitting-oil outlet tube to pump 83 1 1898-K-531 1" long, 0.5"-20 male thread,

0.44"-24 female, 0.19" hole,included in item 226.



ITEM PART NAME MODEL QTY NUMBER DESCRIPTION244 Nut-oil pump outlet tube 83 1 1898-J-504 0.59" long, 0.44"-24 male thread,

0.25" hole, 0.44" across flats,included in item 236.

245 Clamp-pump outlet tube 83 1 A-1898-K-245 1.75" long, 1 hole 0.62" dia., 1 hole0.41" diameter, includes item 246.

246 Grommet-oil pump tube clamp 83 2 1898-M-247 0.86" dia. with 0.38" dia. hole,0.31" thick, included in item 245.

247 Clutch-P.T.O. driving 65, 83 1 2848-H-86 5 dog jaws, 2.25" O.D., 1.38"- 6internal spline.

248 Retainer-drive clutch 65, 83 1 1829-D-680 1.38" O.D., 0.41" I.D. 0.13" wide.249 Lockwasher-drive clutch retainer 65, 83 1 1229-E-421 Internal tooth type, 0.69" O.D.,

0.04" wide.250 Capscrew-drive clutch retainer 65, 83 1 S-267-2 0.38"-16, 0.88" long, 0.56" across

washer flats, grade 8.251 Clutch-P.T.O. sliding 65, 83 1 2848-J-88 5 dog jaws, 2.75" O.D., 1.38"-6

internal spline, includes externalshift groove.

252 Gasket-P.T.O. carrier to bearing 83 - 2297-Z-7098 Silicone gasket, use as required.*253 Plug-expansion 65 1 P-42 Hex socket-female, 0.13"-27

N.P.T.F., non-magnetic.83 1 PW-210 0.63" O.D., 0.06" wide, included in

item 222.254 Tag-oil instruction 65, 83 1 A-1898-C-55

255 Plug-P.T.O. carrier 65, 83 1 1850-T-150 0.75"-14 male square head with

0.13" diameter drill hole in head.256 Bushing-governor drive gear - 1 1199-M-1105 Not used on T-32 models in this

book.257 Gasket-governor drive gear hole - 1 2808-K-687 Not used on T-32 models in this

book.258 Plug-governor drive gear hole - 1 1850-S-45 Not used on T-32 models in this

book.259 Cotter-shift lever stud 65, 83 1 K-238 0.09" diameter, 1" long.260 Nut-shift lever stud 65, 83 1 NL-28-1 0.5"-20, 0.44" high, 6 slots,

0.75" across slots, grade 8.261 Washer-shift lever stud 65, 83 1 WA-38 1.06" O.D., 0.53" I.D., 0.09" wide.262 Stud-shift lever 65, 83 1 4-X-657 0.5"-13/0.5"-20, 1.63" long, 0.13"

drilled hole in 0.5"-20 thread,included in item 222, for on-highwayapplication. For off-highway use4-X-1521.

263 Ball-shift shaft lock 65, 83 1 1898-H-34 0.31" diameter.264 Spring-shift lock ball 65, 83 1 2858-T-20 0.31" O.D., 0.21" I.D., 0.53" free

length, 5.5 coils.265 Setscrew-shift shaft lock ball 65, 83 1 3-X-161 0.38"-16, 0.31" long.266 Lockwasher-shift lock screw 65, 83 1 1229-E-421 Internal tooth type, 0.69" O.D.,

0.04" wide.267 Setscrew-shift shaft and fork 65, 83 1 26-X-56 0.31"-24 thread, 0.53" long.268 Fork-P.T.O. shift 65, 83 1 2849-Y-77 2.06" center shifter shaft hole to end

fork tang, 0.53" diameter shaft hole,0.31"-24 setscrew hole, 2.31"between tangs.



ITEM PART NAME MODEL QTY NUMBER DESCRIPTION269 Oil Seal-shift shaft 65, 83 1 A-1805-B-158 0.81" O.D., 0.56" I.D., 0.12" wide,

vulcanized rubber in metal retainer,included in item 222 (Y-285).

270 Cotter-shift lever 65, 83 1 K-238 0.09" diameter, 1" long.271 Washer-shift shaft 65, 83 1 1829-J-244 0.94" O.D., 0.58" I.D., 0.03" wide.272 Lever-shift 65, 83 1 2847-E-291 0.25" wide with 1 hole 0.52" dia.,

1 hole 0.44" diameter and 1 ovalhole 0.76" x 0.57".

273 Shaft-P.T.O. shift 65, 83 1 2843-C-107 5.09" overall length, 0.56" dia.,1.41" length of bend, shaft has 2notches 0.56" apart.


NUMERICAL PARTS INDEXPART NUMBER PAGE PART NUMBER PAGE PART NUMBER PAGE

3-X-161 21, 25 1846-B-2 8 2803-W-491 204-X-653 12 1846-Y-103 22 2803-X-492 204-X-657 21, 25 1846-V-126 24 2803-V-568 234-X-769 19 1846-L-246 22 2803-W-569 235-X-729 19 1846-M-351 15 2803-X-570 239-X-16 15 A-1850-R-18 12 2808-K-687 2510-X-645 18, 22 1850-Q-43 21 2843-G-7 816-X-40 23 1850-S-45 25 2843-C-107 2616-X-70 13 1850-K-89 12 2843-D-108 2126-X-56 21, 25 1850-T-150 15, 25 2847-T-254 211199-M-1105 13, 25 1854-R-70 13, 16 2847-E-291 261199-Y-1247 13 1874-A-105 23 A2-2847-Q-303 24A-1199-C-1043 16 1898-H-34 21, 25 A-2847-R-304 24A-1199-P-1394 16 A-1898-C-55 25 2847-Z-312 14, 17, 201227-B-496 22 1898-E-57 8 A-2847-U-541 241227-L-714 7, 12, 13, 17, 1898-G-241 24 A-2847-Z-806 8

18, 20, 23 A-1898-K-245 25 2848-R-70 211227-C-939 23 1898-M-247 25 2848-H-86 251228-K-37 24 1898-Q-251 24 2848-J-88 251229-Q-277 7, 12, 14, 17, 1898-J-504 24, 25 2849-P-42 9

18, 22 1898-K-531 24 2849-Y-77 21, 251229-E-421 21, 25 1898-L-532 24 2858-A-1 81229-E-1331 23 A-1898-W-595 24 2858-T-20 251229-K-1597 12, 24 1898-T-670 13 2858-H-86 211229-E-1669 23, 24 1898-U-671 13 2858-W-101 241718-D-108 18 1898-T-696 13 2858-X-102 241744-D-4 18 1898-H-866 24 3280-C-1979 201745-M-13 18 1898-J-868 24 3289-X-206 101779-Q-147 18 2000-S-1397 22 3289-X-1038 11A-1805-Z-26 8 2203-X-336 16 A1-3290-P-1056 9A-1805-C-107 7, 11, 14, 17, 2203-Y-337 16 3719-D-56 22

19, 20 2203-Z-338 16 A3-3722-A-105 18A-1805-B-158 21, 26 2247-D-1252 22 A6-3722-L-194 22A-1805-W-335 22 A-2258-Y-649 18 A-3736-W-647 18A-1805-N-352 23 2258-Q-719 22 A1-3736-V-126 221825-W-101 10 2297-Y-4835 15 A6-3761-D-4 181827-E-109 13, 16 2297-L-6720 22 A-3819-E-421 181828-H-138 7, 11 2297-Z-7098 7, 8, 10, 11, A-3826-F-162 111829-J-244 20, 26 13, 14, 16, 17, A-3826-G-163 231829-T-306 19 20, 23, 24, 25 A-3826-H-164 211829-J-374 10 2758-L-12 18 3826-X-284 111829-X-674 11 2803-L-220 7, 16, 17 A-3826-Y-285 241829-D-680 25 2803-M-221 7, 12, 16, 17 A-3826-T-306 111829-F-864 10 2803-N-222 7, 16, 17 3855-L-12 81844-Q-121 20 2803-T-384 13 3855-D-420 81844-M-455 11 2803-U-385 13 3866-A-235 161844-H-476 22 2803-V-386 13 3866-T-358 121844-J-660 19 2803-V-490 20 3866-B-392 16

27

NUMERICAL PARTS INDEXPART NUMBER PAGE PART NUMBER PAGE PART NUMBER PAGE

A-3866-Z-234 12 A-3911-X-336 19 WA-15C 18, 20, 23A-3866-G-293 20 332 13, 14, 16, WA-16 7, 8, 11, 12,A-3866-M-299 14 17, 23 14, 15, 16,A-3866-S-357 23 335 23 17, 22A-3866-V-672 7, 17 339 13, 14, 16, 17 WA-17 18A-3866-X-1142 12 342-S 13, 14 WA-18 19A-3875-L-272 8 14137-A 20 WA-38 21, 25A2-3875-V-360 8 14274 20A1-3875-C-393 9 K-238 20, 21, 25, 26A3-3875-X-544 9 K-2412 7, 12, 13, 17,A1-3875-E-837 9 18, 20, 22, 233876-L-168 10 KIT T-32-1 43876-H-268 11 KIT T-32-2 43880-P-250 13 KIT T-32-3 43880-Q-251 14 KIT T-32-4 53880-R-252 20 KIT T-32-5 53880-D-264 14 KIT T-32-6 53880-Z-702 14 KIT T-32-7 53880-K-713 23 KIT T-32-8 63880-F-838 15 KIT T-32-9 63880-Y-935 7 KIT T-32-10 63880-Z-936 7 LW-1612 223880-L-948 15 MPS 4126 6, 233892-Y-519 15 N-16-1 12, 193892-Z-520 15 N-17-1 18, 223892-A-521 15 NL-16-1 93892-T-618 15 NL-28-1 21, 25A-3892-F-630 10 P-14 15A-3892-L-1442 10 P-16 93892-M-1443 15 P-24 93892-N-1444 15 P-42 9, 253892-A-2445 10 P-112 153892-B-2446 10 PW-210 25A-3892-A-4135 10 RV-354 22A-3892-K-4379 10 S-256P-2 18, 23, 243892-L-4380 15 S-267-2 8, 11, 12,3892-M-4381 15 16, 253892-N-4382 15 S-268-2 12, 14, 15, 163892-P-4384 10 S-269-2 16, 243897-V-386 7, 12, 14, 17 S-277-2 183897-W-387 14 S-1613-2 93897-B-470 7, 17 S-2511-2 203897-T-774 7, 14, 17 S-2611-2 7, 12, 173897-N-1002 7, 14, 17, 18, S-2612-2 17

22, 23 S-2613-2 17A-3897-Y-3145 19 S-2614-2 123897-M-3185 12 S-2621-D2 22A-3911-M-325 22 S-2816-2 19

28

We warrant all new parts for one year from date of shipment to the buyer against defective material or workmanship (but not against damage caused by accident, abuse or improper installation, maintenance or repair) when such parts are used on vehicles the specifications of which have been approved by our Engineering Department.

As the exclusive remedy under this warranty, we will, at our option, repair or replace such parts free of charge, or take back the nonconforming parts and refund the monies paid by buyer for such parts, if found on examination by us to be nonconforming and if any necessary return charges are prepaid.

If it is necessary to return any parts under this warranty, buyer agrees not to make any deduction on account thereof from remittances on current accounts while claims are in the process of disposition. Any expense incurred without our consent for repairs or replacement will not be allowed.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS, IMPLIED OR STATUTORY, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE. IN NO EVENT SHALL SELLER BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

Only genuine ArvinMeritor replacement parts are covered by this aftermarket parts warranty.

Information contained in this publication was in effect at the time the publication was approvedfor printing and is subject to change without notice or liability. ArvinMeritor reserves the right torevise the information presented or discontinue the production of parts at any time.

Commercial Vehicle Aftermarket

Meritor Heavy Vehicle Systems, LLC7975 Dixie HighwayFlorence, KY 41042 USA888-725-9355 © Copyright 1997 Revised 12/97www.arvinmeritor.com ArvinMeritor, Inc. Litho in U.S.A. PB-90202 (05060)

ARVINMERITOR AFTERMARKET PARTS WARRANTY

t-32 series transfer casesgraphicvillage.org/meritor/pb90202.pdf · t-32 series service kits kit...

Documents