ta 200 quick start r4

8/9/2019 TA 200 Quick Start R4

1/12

TransAccess 200

Quick Start GuideCongratulations on your purchase of theTransAccess 200. This Quick Start

Guide describes the steps necessary to

unpack, install, and initialize your new

equipment. It is strongly recommended

that you read this entire document beforeproceeding.

________________________________________________________________

Rev. 4 940-00008-002

This document is supplemental to the full

Operations Manual for the TransAccess 200.

____________________________________________________________

08/03/04


2/12


3/12

C

Match the holes in the mounting ears tothe tapped holes in the relay rack.Attach theshelf to

the rack. Be sure to mount the equipment so that it

matches the mounting space boundaries

on the rack. All 4 holes must line up.

Use #12-24 screws.

D

Install the airbaffle(s)

(Optional).

Install air baffles if

airflow would

otherwise berestricted.

The baffle mountingears may already be attached.

For offset mounting reverse the ears.

The tray of the baffle must be slanted up towards the rear.

Match the holes in the air baffle with the tapped holes in the relay rack directlybelow the installed shelf.

Use #12-24 screws.

Note: An air baffle may not be required if there is appropriate vent space.

____________________________________________________________________________________________________________________________

08/03/04 Rev. 4 940-00008-002


4/12

E

Note that the TransAccess 200 may be

shipped with two or more RedundancyInterface Modules (RIMs) already

installed.

Install the

RedundancyInterface

Module(s)(RIMs).

Install RIMs in the appropriate slots on

the back of the TransAccess 200 shelf.

One OUT RIM and one IN RIM arerequired per Service Module pair. Note

the keying feature.

Firmly insert the RIM into the shelf until it is fully engaged. Secure each RIM with

the screws provided.

____________________________________________________________________________________________________________________________

08/03/04 Rev. 4 940-00008-002


5/12

Step 2

Install Office Wiring

A

Connect OfficeBattery.

Connect "A" and/or "B" -48V to J33 on therear of the TransAccess 200 shelf. (Refer to

Section 2.5 in the Operations Manual for pinouts.

Connect corresponding ground connections to

J33 also.

Use up to 12 gauge wire (14 gauge

recommended).

Do not turn the power on.

B

Connect Minor and Major alarms to J32 on the

rear of the TransAccess 200 shelf.Connect Office

Alarms.

Use up to 18 gauge wire.

Common, Normally-open, and Normally-

closed contacts are provided.

See Section 2.5 of the Operations Manual for

more details.

____________________________________________________________________________________________________________________________

08/03/04 Rev. 4 940-00008-002


6/12

C

Connect T1/E1 connections using

Turin Networks PM13/PM13E

IN/OUT cables (part number 815-00064-XXX).

ConnectPM13/PM13E

Module facilitiesto the RIMs.

Connect T3/STS-1/AU3 connections

using Turin Networks coax cableassembly (part number 815-00033-

XXX).

D

Connect OMX3Module tofacilities or

PM13/PM13E.

Connect T3/STS1/AU3

connections using Turin

Networks Coax Cableassembly (part number

815-00082-XXX).

Note: Installing aTerminal RIM Set (part

numbers 820-00082-001, 810-00072-001/002, 810-00073-001) eliminates the need

for external coaxial cable connections to the PM13/PM13E Modules.

____________________________________________________________________________________________________________________________

08/03/04 Rev. 4 940-00008-002


7/12

Step 3

Install Modules

A

Install MPUModules.

Install one or two (for redundancyoperation) MPU Modules into the left-

most slots of the TransAccess 200 shelf.

Each module must fully engage with theconnector in the backplane. Tighten the

thumbscrew on the front of the MPU

Module.

Note: Modules may be pre-installed in the

TransAccess 200 at the factory.

B

Install up to 14 Service Modules into the

slots adjacent to the MPU Modules.Install Service

Modules.

The Service Modules must be installed inthe appropriate slots to match the

Redundancy Interface Modules

configurations at the rear.

Each module must fully engage with the

connector in the backplane. Tighten thethumbscrew on the front of each module.

Note: Modules may be pre-installed in the TransAccess 200 shelf at the factory.

____________________________________________________________________________________________________________________________

08/03/04 Rev. 4 940-00008-002


8/12

C

ConnectOpticalCables

Connect two optical cables

to each OMX3 Module.Be very gentle whensliding in the connectors.

Note: Eye Protection isrecommended in areas

near fiber optic equipment.

To avoid possible eye damage, connect the fiber cables to the OMX3 modules prior

to inserting them into the shelf. Do not remove optical cables while the OMX3module is plugged into the shelf.

____________________________________________________________________________________________________________________________

08/03/04 Rev. 4 940-00008-002


9/12

Step 4

Power-up & Initialize the shelf

A

Power-up theTransAccess

200 shelf.

Turn on "A" and/or "B" Battery by

throwing the appropriate switch or

inserting the appropriate fuse at the

Distribution Fuse Panel.

After the MPU status LED turnsgreen, momentarily (less than 1

second) press the Lamp Test button on

either MPU Module. The LED on

each module in the shelf should illuminate.

RTN

B

Connect theUser InterfaceDevice (UID).

Connect the User Interface

Device (UID) (customer-supplied PC or Terminal) to the

User System Interface (USI) port

on the MPU Module.

Note: the UID may be connected

to either MPU Module.

Use Turin Networks cable 815-

00011-XXX.

____________________________________________________________________________________________________________________________

08/03/04 Rev. 4 940-00008-002


10/12

C

Launch theterminalprogram on

the UID.

Start a VT100 terminal program.(Settings are VT100 emulation,

Data Bits = 8, Parity = none, Stop

Bit = 1, Flow Control = none, BaudRate = 1200 up to 115,200)

Press "Enter" twice to initiate

communications with theTransAccess 200.

Enter the password at the Login prompt (default is "admin" to login).

____________________________________________________________________________________________________________

08/03/04 Rev. 4 940-00008-002

D

Select "System" at the top-levelmenu.

"Discover"the node

configuration. Select "Discover" in the drop-down

menu.

Type "y" to confirm your choice

and press "Enter".

E

Select "MPU" at the top-level

menu..

Select "IP/SNMP Config" in the

drop-down menu.

Set the IP

Address andgateway for

Telnet/SNMPO eration

Move the cursor to the IP and

Gateway locations and enter the

address. ^S to save.

________________


11/12

F

.Configurethe moduleoptions.

From the Main Menu, select "Service Module", then "PM13/PM13E" or "OMX3".

Under "PM13/PM13E" for example, select "Configuration" and "Line".

Configure the "Line" settings as required. Change the default template to alter the

default configuration.

Press the "Tab" key to

switch to the Dropconfiguration.

An LBO setting of "0" takes a T1 out of service. All 28 T1's are disabled by default.

Note: Defaultconfiguration settings areloaded when the

TransAccess 200 is

initially powered up. Youonly need to change those

configuration parameters

that will not remain at the

default settings.

____________________________________________________________________________________________________________________________

08/03/04 Rev. 4 940-00008-002


12/12

____________________________________________________________________________________________________________________________

08/03/04 Rev. 4 940-00008-002

G

Connect appropriate test set(s) to the OC3/STM-1,T3/STS-1/AU3, and T1/E1 facilities connections.Verify integrityof the circuits.

Verify error-free transmission through eachTransAccess 200 service module.

If errors occur, check the configuration

(especially LBO settings) and retest.

Turin NetworksInc.1415 N. McDowell Blvd

Petaluma, CA 94954

Phone: (707) 665-4400

Fax: (707) 792-4949

www.turinnetworks.com
http://www.turinnetworks.com/http://www.turinnetworks.com/

ta 200 quick start r4

Documents