ta35涂鸦电机说明书(220v) a版英文编辑 20200319

AC tubular motor user instruction

6 7 8

TA35-5/22WE⑤ ⑥

Motor shakes two times. After setting the up limit,if the motor is in the upper limit position, press the [up/open]button,

the motor will not respond at this situation.

二、Limit position settingUp limit position setting

Simultaneously press [Channel setting]+

[UP] button for 4 seconds to enter the se-

tting open limit point state.

① ②

Motor will make a long sound:Bi.And then it shakes two times.

Operation:Within 3 minutes.

4S 3V CR2032Bi~

3min

③

Long press the [channel setting] button for 4

seconds

Press [Up],[Down],[Up tilting]or[Down tilting]

to run the motor to the favorite position.

④3V CR2032

4S

Limit setting

一、Limit status1.The factory state of the motor is no travel state. Press the up/down button of the remote

control to inching control, motor will work during pressing button period. You need to set

the up and down limit to enter the normal working state.

2.Delete the limit, the motor goes back to the factory state,need to reset the limit, the motor

can enter the normal using state.

Limit setting process:

Set up limit Set down limit

Original status

(EXW mode)Can be exchanged

Delete the limit

Normal using status

★1.The limits setting must be performed after the entire curtain system (including traction,

blades,curtains,etc.) is installed.

2.Limit setting need to be setted by remote control. Due to the inherent characteristics of

radio remote control, all motors that can receive the remote control signal during the se-

tting process so it may receive the setting instruction.Therefore, in order to avoid misop-

eration of other curtains, please ensure that the irrelevant curtains are powered off or

inactive.

⑥⑤

To control [open] and [close] button by app, it needs firstly complete up and down limit setting.

Come back to [setting], click [motor reverse

direction], motor change direction.

motor reverse direction

Attention：

Delete limitsNote: the following operation shall be to ensure that the channel of remote control was com-

pleted setted already.

Do not allow to use Power direct control function after delete limits.

Down limit position setting

Simultaneously press [Channel setting]+

[Down] button for 4 seconds to enter the

setting Close limit point state.

① ②

③

4S

3V CR2032

Motor will make a long sound: Bi.And then it shakes two times.

Operation:Within 3 minutes.

Bi~

Press [Up],[Down],[Up tilting]or[Down tiltin-

g] to run the motor to the favorite position.

Long press the [channel setting] button for 4

seconds.

3V CR2032

4S

④

⑤ ⑥

Motor shakes two times.

3V CR2032

4S

Bi-Bi① ②

Bi Bi..and then motor shakes two times.Delete limits (Long press the stop and cha-

nnel setting button together for 4 seconds.)

After setting the down limit,if the motor is in the down limit position,press the [down/close] bu-

tton, the motor will not respond at this situation.

3min

Press Up tilt,up tilt about 15 degree.

① ②

Press Down tilt,Down tilt about 15 degree.

Tilt function

15° -15°

Set the intermediate stop point 1

Set the stop point 1,and the default stop point 1 is 75%.

① ②

③

3V CR2032

Running to favorite position

Note: motor original status,after setting the limits,long press Up tilt,Horizontal,Down tilt and

then it can run to favorite position. Default limit percentages are 75%,50%, 25%.

① ②1.5S

1.5S

75%50%

③

1.5S

25%

2S

④

Press any button to adjust the favorite position.

Bi

Motor shakes two times. After finish the setting, press [up tilt/75%]. the motor will not respond as it is on 75% favorite

position already.

1.5S



① ②

③ ④


Bi

Motor shakes two times. After finish the setting, press [down tilt/25%], the motor will not respond as it is on 25% fav-

orite position already.

3V CR2032

2S

1.5S



① ②

③ ④


Bi

Motor shakes two times. After finish the setting, press [Horizontal/50%],

the motor will not respond as it is on 50% fa-

vorite position already.

3V CR2032

2S

1.5S

Wechat account

RAEX MACHINERY LIMITED

GUANGDONG RAEX INTELLIGENT TECHNOLOGY CO.,LTD.

RAEX MACHINERY LIMITED

-Unit A,2/F,On Wah Industrial Building,41 43 Au Pui Street,Fo Tan,Shatin, N.T.,HongKong.

- -Tel: 00852 26909728 Fax: 00852 26900018

GUANGDONG RAEX INTELLIGENT TECHNOLOGY CO.,LTD.

XiLi Industrial Park,DongChong Town,Nansha district,

CuangZhou,China(Post Code:511475)

- -Tel: 008620 22916189 Fax: 008620 22916154

2 3 4 5

Connection mode

Φ13.6 Φ20

5

26.0 L

4

Φ35

12.012.0

5.5

10 10×

Φ3

Φ4020Φ36.4

TA35-5/22WE

220V AC

50Hz

120W

5.0N.m

22rpm

S2 6min

IP44

F

3V CR2032

①

③④⑤

⑦⑧⑨

②⑥

⑩

2.[phone control]

一、Connection mode

A.C.Powerinput~

开启停止关闭

Distribution network ways

◆Smart distribution network ways

①

◆AP mode

Click adding button in the app. Enter “adding devices”, click “hand adding”, then enter “Con-

necting internet mode’’.

② ③

Remark: You could search TUYA SMART in AppStore or find it in Android searching mark-

et, then download it for free.

To make WIFI on and enter search process,and write down valid Wifi hotspot na-

me and passport.

④

①

Bi-Bi

In the APP, click “Add” Item. Then entering “Adding devices”, click auotmatic discover”,it will

enter Smart distribution network ways. “

Short press programming button 4 times and then long press it.

② ③

10 seconds later, App will show the motor symbol, click next step, and complete all operation.

Motor will make two sounds shortly: Bi Bi.

④

auotmatic discover

complete

Enter wifi password

Manually add-Small home appliance-The curtain

Short press programming button 5 times, then

long pressing it again.

Bi

Motor will make short Bi.one sound.

Distribution network model-Hot spot distribution network

As app guidence,searching wifi name(for example,Smartlife-XXXX), adding device, and co-

mplete all operation.

WIFI-Smartlife-XXXX Add equipment

next step

Limit setting by phone

②①

④③

Click [setting] button, click [limit setting]. Press button, and adjust motor to up limit position, click “up setting button”.

[Clear limit setting].

setting limit setting up setting button

Press button, and adjust motor to down li-mit position, click [down setting button].

down setting button Clear limit setting

电机反向

限位设置

窗帘

Product information

一、Product Size

二、Product Specification

Note: Motor length L subject to product specifications (unit: mm)

Rated voltage

Rated frequency

Rated Power

Rated Torque

Rated Speed

Working System

IP grade

Insulation grade

Motor Mode

三、Recommended control device

①、Led Light ②、Right Channel Select

③、Up/Open

④、Stop

⑤、Down/Close

1.[YR2118B Remote]

⑥、Left Channel Selec

⑦、Up tilt/75% position

⑧、Horizontal 50% position

⑨、Down tilt/25% position

⑩、Channel setting

(Back)(Head)

Basic remote setting

Note

1. , the transmission channel of the remote control into the motor.

2.Each motor can record 16 remote control channels.After that, every time the motor receiv-

es the setted remote control channel signal,it will make corresponding actions.

3.YR2118B is supported.( All RAEX other remotes can match with this motor.)

Before using the remote control function the user must set remote control channel to store

Remote channel setting

Press the [Programming Se-

tting] button for 3 seconds to enter into setting status.

Choose remote channel.

Press the [Programming Setti-

ng] button to confirm and then

motor shakes two times.

Press left button on the back of remote.

Motor will make a long sound:

Bi:And then it shakes two tim-

es.

⑤

Bi~

3V CR2032

⑥

Motor will make sounds shortly: Bi Bi.And then it shakes two times.

Change direction setting

orrespond to the opening and closing directions of the curtain.If direction is opp-

osite,please do change direction setting.

Note: check whether the opening and closing directions of the remote control c-

Bi-Bi

Remote control channel delete

Note: if you need to disable all the setted remote control channels, please do the

"clear remote control channel" operation

Press the [Program-

ming Setting] button

for 3 seconds

Bi~

Press the [Program-

ming Setting] button

for 7 seconds.

7S

Motor shakes two times.(All remote controllers

cannot control the mo-

tor.)


③ ④① ②

① ② ③

④

②① ④③

Bi~

Press the [Programm-

ing Setting] button for

3 seconds


Long press left chann-

el select and stop butt-

on together.

Motor shakes two times.N(Blue) =Neutral L (Brown)=Live

G (Green/Yellow)=Earth

L1(Brown)=Open

N(Blue) =Neutral

ta35涂鸦电机说明书(220v) a版 英文 编辑 20200319

Documents

ta35涂鸦电机说明书(220v) a版英文编辑 20200319