tabla de carga

32
 1 5448 - - - 0205 - - - D  7 RTC-- - 8065 Link-Belt Cranes Technical Data Specifications & Capacities RTC--8065 Telescopic Boom Rough Terrain Crane 65 ton (58.9 metric ton) CAUTION : Thi s mat eri al issuppli edfor refe renc e use only. Operator must refer to in---cab Crane Rating Manua l and Ope rator’s Manual to determine allowable crane lifting capacities and assembly and operating procedures.

Upload: vpizarro23

Post on 07-Oct-2015

27 views

Category:

Documents


0 download

DESCRIPTION

LINKBELT 8065

TRANSCRIPT

  • 15448---0205---D7

    RTC---8065Link-Belt Cranes

    Technical DataSpecifications & Capacities

    RTC--8065Telescopic Boom Rough Terrain Crane

    65 ton (58.9 metric ton)

    CAUTION: Thismaterial is supplied for referenceuseonly. Operator must refer to in---cab Crane RatingManual and Operators Manual to determineallowable crane lifting capacities and assembly andoperating procedures.

  • 5448---0205---D7

    RTC---8065 Link-Belt Cranes

  • 15448---0205---D7

    RTC---8065Link-Belt Cranes

    Table Of ContentsPages

    Specifications 1--4Capacities 1--20

  • 5448---0205---D7

    RTC---8065 Link-Belt Cranes

    This page intentionally left blank

  • Telescopic Boom Rough Terrain Crane

    RTC8065 65ton (58.97 metric tons)

    FE

    Tailswing of Counterweight 13 9.25 4.20

    Turning radius (4wheel steer 23 10 7.26centerline of tires)Turning radius (2wheel steer 46 10 14.28centerline of tires)Turning radius (4wheel steer outside 27 5 8.36front carrier corner)Turning radius (2wheel steer outside 49 10 15.19front carrier corner)

    General Dimensions feet meters

    45 9(13.94 m)

    38 0(11.58 m)

    7 0(2.13 m)

    23.8

    10.9

    20.2

    6 9.5(2.07 m)

    11 9(3.58 m)

    5 9.5(1.77 m)

    11 6(3.51 m)

    27 3.5(8.32 m)

    4 10(1.47 m)

    10 0.75 (3.07 m)

    8 2.5 (2.50 m)Centerline of tires

    16 4.75 (5.00 m)

    23 0 (7.01 m)

    Tire Size

    Dimension 29.5 x 25 29.5 R 25

    A 12 10.75 (3.93 m) 12 11.75 (3.97 m)B 7 11.5 (2.42 m) 8 0.5 (2.44 m)C 2 8 (0.81 m) 2 9 (0.84 m)D 12 5 (3.78 m) 12 6 (3.81 m)E 8.25 (0.21 m) 7 (0.18 m)F 25.25 (0.64 m) 25.25 (0.64 m)G 11.25 (0.29 m) 12.25 (0.31 m)

    10 10.5(3.31 m)

    AB

    C C

    D

    9 5.5(2.88 m)

    3 9(1.14 m)

    3 3(0.99 m)

    7.25(0.18 m)

    G

    Full Retraction

    Intermediate Extension

    Full Extension

    C of RotationL

    RTC8065

  • RTC8065

    Upper Structure BoomPatented Design Boom side plates have diamond shaped

    impressions for superior strength to weightratio and 100,000 psi (689.5 mPa) steelangle chords for lateral stiffness.

    Boom telescope sections are supported bytop, bottom, and adjustable side wearshoes to prevent metal to metal contact.

    Standard Boom 38 115 (11.58 35.05 m) four section

    full power boom Basic mode (or mode B) is the full pow-

    er, synchronized mode of telescoping allsections proportionally 115 (35.05 m).

    The exclusive Amax mode (or modeA) extends only the inner midsectionto 63 6 (19.35 m) offering increased ca-pacities for inclose, maximum capacitypicks.

    Mechanical Boom Angle IndicatorBoom Head Five 16.5 (0.42 m) root diameter nylon

    sheaves handle up to ten parts of wirerope.

    Quick reeve design. Boom head designed for quick reeve of

    hook block. Rope dead end lugs provided on each side

    of boom head. Easily removable wire rope guards. Fly pinning alignment tool.

    Boom Elevation Hydraulic cylinder with holding valve and

    bushing in each end. Hand control for controlling boom

    elevation from 3 to +78.Optional Auxiliary Lifting Sheave Single 16.5 (0.42 m) root diameter nylon

    sheave with removable wire rope guardmounted on boom.

    Use with one or two parts of line. Does not affect erection of fly or use of

    main head sheaves for multiple reeving.Optional 70ton (63.5 mt) 5sheave, quick reeve

    hook block 60ton (54.43 mt) 4sheave, quick reeve

    hook block 40ton (36.28 mt) 4sheave, quick reeve

    hook block 8.5ton (7.7 mt) hook ball Boom floodlight

    FlyOptional 36.5 (11.13 m) one piece lattice fly, stow-

    able, offsettable to 1, 15 or 30 36.5 61 (11.13 18.59 m) two piece (bi-

    fold) lattice fly, stowable, offsettable to 1,15 or 30

    Cab and ControlsEnvironmental ULTRA CAB LFC2000 construction process featuring

    laminated fibrous composite material. Isolated from sound and vibration by a

    neoprene seal. Sixway adjustable operators seat with

    retractable seat belt. Fourway adjustable tilting and locking

    steering wheel. All windows are tinted and tempered

    safety glass. Slide by door opens to 3 (0.91 m) width. Sliding rear and right side windows and

    swing up roof windows for maximum visibility and ventilation.

    Engine dependent warmwater heater withdefroster.

    Handheld outrigger controls. Sight level bubble Hand throttle Audible swing alarm Warning horn Backup alarm Travel lights Cab mounted work lights Sun visor Electric windshield wiper Mirrors Top hatch window wiper Cup holder Fire extinguisher Circulating fan Dome light

    Optional Amber strobe light and rotating beacon Emergency steering system Rear steer indicator Air conditioning

    ControlsHydraulic controls (joystick type) for: Main winch Boom hoist Drum rotation indicators Swing Optional auxiliary winch Optional singleaxis controlsFoot controls for: Boom telescope Swing brake Engine throttle with throttle lock

    Cab InstrumentationCorner post mounted gauges for: Hydraulic oil temperature Fuel Convertor temperature Voltmeter Water temperature Oil pressure Tachometer Audio/visual warning system

    Rated Capacity Limiter Microguard 434 Graphic audiovisual

    warning system built into dash with antitwo block and function limiters.

    Operating data available includes: Crane configuration Boom length Boom angle Head height Radius of load Allowed load Actual load % of allowed loadPresettable alarms include: Maximum and minimum boom angles Max tip height and boom length Swing left/right positions Operator defined area alarm is standard. Antitwo block weight designed for quick

    reeve of hookblock.

    Optional Internal RCL light bar: Visually informs

    operator when crane is approaching maxi-mum load capacity with a series of lights;green, yellow, and red.

    External RCL light bar: Visually informsground crew when crane is approachingmaximum load capacity kickouts and pre-settable alarms with a series of lights;green, yellow, and red.

    Swing Bidirectional hydraulic swing motor

    mounted to a planetary reducer for 360continuous smooth swing at 2 r.p.m.

    Swing park brake 360 electric over hy-draulic (spring applied, hydraulic released)multidisc brake mounted on the speedreducer. Operated by toggle switch in over-head control console.

    Swing brake 360, foot operated, hy-draulic applied disc brake mounted on thespeed reducer.

    Travel swing lock Standard; two posi-tion travel lock (pin device) operated fromthe operators cab.

    Counterweight Pinned to upper struc-ture frame. 12,000 lb (5 443 kg).Optional hydraulically controlled counter-weight removal.

    Optional 360 (pawlingear) swing lock (meets

    New York City requirements). Hydraulic SystemMain Pump Foursection geartype pump Combined pump capacity 132 gpm (500

    Lpm) Mounted on torque converter, powered by

    engine through a pump disconnect Pump disconnect is a spline type clutch

    engaged/disengaged from carrier. Pump operates at 3,500 psi (24.1 mPa)

    maximum system pressure. ORing Face Seal (ORFS) technology

    throughout with hydraulic oil cooler.Pilot Pressure / Brake / CounterweightRemoval Pressure compensated piston pump pow-

    ered by carrier engine. Operates at 2,650psi (18.3 mPa) maximum.

    Telescope/Outrigger/Steering Pump Single geartype pump, 24 gpm (91 Lpm)

    maximum. Mounted on torque converter,powered by engine through a direct me-chanical drive.

    Pump operates at 3,000 psi (20.7 mPa)maximum system pressure.

    Reservoir 170 gal (643.5 L) capacity. Diffuser for

    deaeration.Filtration One, 10micron filter located inside

    hydraulic reservoir. Accessible for easyreplacement.

  • RTC80653

    Control Valves: Six separate pilot operated control valves

    allow simultaneous operation of all cranefunctions.

    Load Hoist SystemStandard 2M rear winch with grooved lagging Twospeed motor and automatic brake Power up/down mode of operation Controls for future addition of auxiliary

    winch.

    Bidirectional pistontype hydraulic motor,driven through a planetary reduction unitfor positive operator control under all loadconditions.

    Asynchronous parallel double crossovergrooved drums minimize rope harmonic motion.

    Winch circuit control provides balanced oilflow to both winches for smooth, simulta-neous operation.

    Line Pulls and Speeds Maximum line pull 16,506 lb (7 487 kg) and

    maximum line speed of 454 f.p.m. (138.4m/min) on standard 16 (0.41 m) root diam-eter grooved drum.

    Rotation resistant ropeOptional 2M front winch with twospeed motor and

    automatic brake, power up/down mode of operation.

    Hoist drum cable followers Third wrap indicators

    Carrier Type 10 10.5 (3.31 m) wide, 151 (3.84 m)

    wheelbase. 4 x 4 x 4 (4wheel steer, 4wheel drive)

    For rough terrain with limited turning area.Frame 100,000 psi (689.5 mPa) steel, double

    walled construction. Integral 100,000 psi (689.5 mPa) steel out-

    rigger boxes.Standard Carrier Equipment Two front, rear, and midpoint carrier

    steps. Nonslip safety strips on carrier deck Deep front storage Fenders Pontoon storage Full lighting package Front towing shackles

    Optional Front and rear mounted pintle hook Front tow winch

    EngineEngine Caterpillar 3126B 7.2LCylinders cycleBoreStrokeDisplacementMaximum brake hpPeak torque (ft. lb.)Electric systemStarting systemFuel capacityAlternatorCrankcase capacity(total system)

    6 44.33 in. (110 mm)5.00 in. (127 mm)442 cu. in. (7.2 L)225 @ 2,200 rpm646 @ 1,500 rpm12 volt12 volt95 gal (359.6 L)130 amps30 qt (28.4 L)

    Water/fuel separator on engine ther injection package

    Transmission Spicer offhighway threespeed, two

    range power shift transmission. Six speeds forward and reverse. Front axle disconnect for two or fourwheel

    drive.

    Axles Front and Rear Heavy duty planetary

    drive/steer type Front axle disconnect

    SuspensionFront Axle Rigid mounted to frame

    Rear Axle Pin mounted on bronze bushings. Auto-

    matic hydraulic rear axle oscillation lockout cylinders engage when upper structurerotates 2.5 past centerline.

    Steering Hydraulic twowheel, fourwheel, and

    crab steering. Modes selected by toggle switch on dash. All modes fully controlled by steering

    wheel.Optional Rear steer indicator

    TiresFront and Rear Standard 29.5 x 25 (28PR) Earthmover

    typeOptional 29.5R25 XHA 1 star radials Spare tires and rims.

    BrakesService Hydraulic disctype brakes at each wheel

    end.Parking/Emergency Disctype, spring applied, hydraulic re-

    leased, fade resistant, operated from cab,mounted on front axles.

    Outriggers Three position operation capability. Four hydraulic, telescoping beam and jack

    outriggers. Vertical jack cylinders equipped with

    integral holding valve. Beams extend to 23 0 (7.01 m) center-

    linetocenterline and retract to within 1010.5 (3.31 m) overall width.

    Equipped with stowable, lightweight 23.5 x27.25 (59.7 x 69.2 cm) hexagonal steel pontoons.

    Controls and sight level bubble located incab.

    Confined Area Lifting Capacities(CALC) System Three operational outrigger configurations

    are available: Full extension 23 0 (7.01 m) Intermediate position 16 4.75 (5.00 m) Full retraction 10 0.75 (3.07 m)

    For confined area operation, rated liftingcapacities are provided for the intermedi-ate and fully retracted outrigger positions.

    When the outrigger position levers (locatedon the outrigger beams) are engaged, theoperator can set the crane in the intermedi-ate or full retraction outrigger position with-out having to leave the cab.

    Optional Outrigger cover package

    Travel Speeds and Gradeablity

    Tires 29.5 x 25

    Maximum Speed 19.5 mph(31.4 km/h)Gradeablity at 70% conver-tor efficiency 112.9%

    Maximum Tractive Effort at70% convertor efficiency

    76,715 lb (34 797 kg)

    Gradeablity at 1.0 mph (1.6km/hr) 55.6%Maximum Tractive Effort at1.0 mph (1.6 km/hr)

    50,516 lb (22 914 kg)

    Crane operating angle must not exceed 35 (77% grade).Numbers reflect main hydraulic pump engaged.

  • RTC8065

    Axle LoadsBase crane with standard 38 115

    Upper facing front Upper facing rear(11.58 35.05 m) foursection boom, 2M

    main winch with 2speed hoisting and G.V.W.

    Front axle Rear axle Front axle Rear axlepower up/down, 630 (192 m) 3/4 (19mm) wire rope. 4x4x4 carrier with Cater- lb kg lb kg lb kg lb kg lb kgpillar 3126B 7.2L engine, 29.5 x 25 tires,counterweight, and no fuel. 91,488 41 498 44,296 20 092 47,192 21 406 41,804 18 962 49,684 22 253Remove 29.5 x 25 tires and wheels 6,732 3 054 3,366 1 527 3,366 1 527 3,366 1 527 3,366 1 52729.5R25 XHA Tires 964 438 482 219 482 219 482 219 482 219Remove outrigger beams 5,235 2 374 2,461 1 116 2,774 1 258 2,461 1 116 2,774 1 258Tow winch 686 311 1,002 454 316 143 1,002 454 316 143100 gal (378.5 L) fuel 685 310 364 165 321 145 364 165 321 1452M auxiliary winch with 630 (192 m) of3/4 (19 mm) rope 779 354 203 92 982 445 920 417 141 64Remove front carrier counterweights 3628 1 646 4,858 2 204 1,230 558 4,858 2 204 1230 558Hydraulic counterweight removal 353 160 163 74 190 86 518 235 165 75Remove counterweight 12,000 5 443 6,586 2 987 18,586 8 430 17,633 7 998 5,633 2 555Air conditioning 287 130 55 25 232 105 209 95 78 3536.5 (11.13 m) onepiece lattice fly, withtip lugs, stowable 1,542 700 2,485 1 115 619 415 1,039 471 2,581 1 171

    36.5 61 (11.13 18.59 m) twopiece(bifold) lattice fly, stowable 2,250 1 021 3,165 1 436 915 415 1,094 496 3,344 1 517Fly storage brackets with all fly options 160 73 228 103 69 30 81 36 241 109Auxiliary lifting sheave assembly 110 50 355 152 225 102 233 106 343 1568.5ton (7.71 mt) hook ball @ front bumper 360 163 566 256 206 93 n/a n/a n/a n/a70ton (63.50 mt) 5sheave hook block@ front bumper 1,390 631 2,186 992 796 361 n/a n/a n/a n/a

    60ton (54.43 mt) 4sheave hook block@ front bumper 1,150 522 1,809 821 659 299 n/a n/a n/a n/a

    Adjust gross weight and axle loading according to component weight. Note: All weights are 3%.

    Tire Max. Axle Load @ 20 mph (32.2 km/hr)29.5 x 25 (28PR)

    29.5R25 XHA 1 Star53,000 (24 041 kg)53,000 (24 041 kg)

    LinkBelt Construction Equipment Company Lexington, Kentucky www.linkbelt.comLinkBelt is a registered trademark. Copyright 2005. All rights reserved. We are constantly improving our products and therefore reserve the right to change designs and specifications.

  • 5448---0205---D7

    RTC---8065 Link-Belt Cranes

    This page intentionally left blank

  • 5448---0205---D7

    RTC---8065 Link-Belt Cranes

    This page intentionally left blank

  • 5448---0205---D7

    RTC---8065 Link-Belt Cranes

    This page intentionally left blank

  • 5448---0205---D7

    Link--Belt Construction Equipment Company Lexington, Kentucky www.linkbelt.comRLink--Belt is a registered trademark. Copyright 2005. We are constantly improving our products and therefore reserve the right to change designs and specifications.