table saw. general safety wear your safety glasses at all times take off all jewelry do not wear...
TRANSCRIPT
![Page 1: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/1.jpg)
Table Saw
![Page 2: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/2.jpg)
General Safety
Wear your safety glasses at all times
Take off all jewelry
Do not wear loose clothing
Make sure you are the only person in the safety zone when operating the table saw.
![Page 3: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/3.jpg)
General Safety continued
Do the entire operation yourself
Never pass your hands over the blade to remove scrap material
Never pass your hands over the blade
Always have one hand or the push-stick on the material
Never back out of a cut
The guard must be in place at all times
![Page 4: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/4.jpg)
Components of the Table Saw
Arbor
Miter Gauge
Fence
Support Arm
Guard
Splitter
![Page 5: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/5.jpg)
Components of the Table Saw
Push Sticks
Front Hand Wheel
Side Hand Wheel
![Page 6: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/6.jpg)
Set-up of the Table Saw
One face and one edge must be flat to use the table saw.
The blade must be 1/8” to 1/4” above the material being cut.
OR One Tooth
Do not lower the support arm or raise the guard unless you have special permission from the teacher and are being monitored by the teacher.
![Page 7: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/7.jpg)
Operations of the Table Saw
Ripping
Cross cutting
Bevel
Miter
Groove
Dado
Rabbet
![Page 8: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/8.jpg)
Arbor
![Page 9: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/9.jpg)
Miter Gauge
![Page 10: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/10.jpg)
Fence
![Page 11: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/11.jpg)
Support Arm
![Page 12: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/12.jpg)
Guard
![Page 13: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/13.jpg)
Splitter
![Page 14: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/14.jpg)
Push Sticks
![Page 15: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/15.jpg)
Front Hand Wheel
![Page 16: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/16.jpg)
Side Hand Wheel
![Page 17: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/17.jpg)
Ripping
Ripping is defined as cutting along the material’s length
OR Cutting with the grain
![Page 18: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/18.jpg)
Cross cutting
Cross cutting is defined as cutting the material’s length
OR Cutting across the grain
![Page 19: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/19.jpg)
Bevel
A Bevel is defined as cutting along the material’s length at an angle.
OR Cutting with the grain at an angle
![Page 20: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/20.jpg)
Miter
A miter is defined as cutting the material’s length at an angle
OR Cutting across the grain at an angle
![Page 21: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/21.jpg)
Groove
A Groove is defined as cutting a “slot” along the material’s length but not through the full thickness of the material
OR Cutting a “slot” with the grain but not
through the full thickness of the material
![Page 22: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/22.jpg)
Dado
A Dado is defined as cutting a “slot” across the material’s width but not through the full thickness of the material
OR Cutting a “slot” across the grain but
not through the full thickness of the material
![Page 23: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/23.jpg)
Rabbet
A Rabbet is defined as cutting a square edge or end across or with the grain but not through the full thickness of the material.
![Page 24: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/24.jpg)
Ripping
![Page 25: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/25.jpg)
Cross cutting
![Page 26: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/26.jpg)
Bevel
![Page 27: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/27.jpg)
Miter
![Page 28: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/28.jpg)
Groove
![Page 29: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/29.jpg)
Dado
![Page 30: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/30.jpg)
Rabbet
![Page 31: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/31.jpg)
Operation Procedure 1 (Ripping)
1. Raise the Splitter.
![Page 32: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/32.jpg)
Raising the Splitter
![Page 33: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/33.jpg)
Operation Procedure 2 (Ripping)
2. Raise the blade to its maximum height.
Using a try-square, square the blade to the table.
![Page 34: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/34.jpg)
Squaring the Blade
![Page 35: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/35.jpg)
Operation Procedure 3 (Ripping)
3. Adjust the blade height. One tooth above the material.
![Page 36: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/36.jpg)
Adjust the blade height
![Page 37: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/37.jpg)
Operation Procedure 4 (Ripping)
4. Determine the width of your material that will be cut and set the fence.
If the material is 5” in width or less, push sticks are required.
The material you are going to be using always goes between the fence and the blade.
![Page 38: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/38.jpg)
Setting the Fence
![Page 39: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/39.jpg)
Operation Procedure 5 (Ripping)
5. Lower the guard.
Keep the material tight against the fence.
Be sure the material is not in contact with the blade when the machine is turned on.
Stand to the left of the blade path.
![Page 40: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/40.jpg)
Lowering the Guard
![Page 41: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/41.jpg)
Tight against the Fence
![Page 42: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/42.jpg)
Operation Procedure 6 (Ripping)
6. Turn the machine on.
Slide the material against the fence and through the blade.
Push the material all the way off the table.
![Page 43: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/43.jpg)
Ripping operation.
Material more than 5” in width. No push sticks required.
![Page 44: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/44.jpg)
Ripping operation.
Material less than 5” in width. Push sticks required.
![Page 45: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/45.jpg)
Operation Procedure 1 (Cross cutting)
1. Slide the splitter down
![Page 46: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/46.jpg)
Splitter down
![Page 47: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/47.jpg)
Operation Procedure 2 (Cross cutting)
2. Set the miter gauge in the left groove on the table.
![Page 48: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/48.jpg)
Miter gauge placement
![Page 49: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/49.jpg)
Operation Procedure 3 (Cross cutting)
Raise the blade to it’s maximum height.
Using a try-square, square the miter gauge.
![Page 50: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/50.jpg)
Squaring the Miter Gauge
![Page 51: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/51.jpg)
Operation Procedure 4 (Cross cutting)
4. Adjust the blade height. One tooth above the material.
Keep the material tight against the miter gauge.
Be sure the material is not in contact with the blade when the machine is turned on.
Stand to the left of the blade path.
![Page 52: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/52.jpg)
Tight against the Miter Gauge
![Page 53: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/53.jpg)
Operation Procedure 5 (Cross cutting)
5. Line up the end of your material to take off approximately 1/8” (or a blade width) to square one side of your material.
Lower the guard.
Turn the machine on.
Slide the material through the blade cutting the 1/8” off the material
![Page 54: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/54.jpg)
Line up the Material
![Page 55: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/55.jpg)
Cross cutting Operation
![Page 56: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/56.jpg)
Operation Procedure 6 (Cross cutting)
6. Check for the end to be square to the edge
![Page 57: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/57.jpg)
Checking for Square
![Page 58: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/58.jpg)
Operation Procedure 7 (Cross cutting)
7. If the edge to end is square you may move on. If not, repeat steps 1-6 until and end to edge is square.
Jump the miter gauge to the groove in the right of the table
![Page 59: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/59.jpg)
New Miter Gauge Placement
![Page 60: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/60.jpg)
Operation Procedure 8 (Cross cutting)
8. Set the fence to the specified length.
Set the material’s end on the fence and edge on the miter gauge.
![Page 61: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/61.jpg)
Material Placement
![Page 62: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/62.jpg)
Operation Procedure 9 (Cross cutting)
9. Holding your material in place against the miter gauge, MOVE THE FENCE OUT OF THE WAY!
The fence is used only for measuring purposes when cross cutting.
![Page 63: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/63.jpg)
Moving the fence
![Page 64: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/64.jpg)
Operation Procedure 10 (Cross cutting)
10. Turn the machine on.
Slide the material all the way through the blade.
![Page 65: Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the](https://reader036.vdocument.in/reader036/viewer/2022062518/56649ed25503460f94be1872/html5/thumbnails/65.jpg)
Final Cross Cut