table top tv stand instruction manual
TRANSCRIPT
Model: PSTVS04
Table Top TV Stand Instruction Manual V3.0
Thank you for choosing this PERLESMITH product! At PERLESMITH we strive to provide you with the best quality products and services in the industry. Please share your experience of our product with others at www.perlesmith.com/pages/reviews if you are satisfied. Should you have any issues, please don't hesitate to contact us.Technical Support:1-800-556-6806 Mon-Fri 10am - 5pm (PST) (USA) (CAN)Other Info:[email protected] (US)[email protected] (CA)
Website: www.perlesmith.com
P1
Want to watch a video that show how to install the TV brackets.
WE’RE HERE TO HELP
Want to watch a video that show how to add the safetylocks.
Watch it now at: https://youtu.be/kC4JmnNCDwM
Watch it now at:https://youtu.be/MYjAmxcl1go
IMPORTANT SAFETY INFORMATION
Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact our Technical Support line at 1-800-556-6806 or customer service at [email protected] (US)/ [email protected] (CA).
CAUTION: Avoid potential personal injuries and property damage!
Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We are not liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
P2
Wrench
Check the VESA Pattern of TV before the Installation
Minimum VESA pattern: 100mm/4 in.(W)x100mm/4 in.(H)
If your TV VESA is greater than 400x400 mm/16x16 in. or less than VESA 100x100mm/4x4in., this TV stand is NOT compatible.
If this TV stand is NOT compatible, please contact customer service at [email protected] (US)/ [email protected] (CA) to find a compatible product.
MAX: 400mm/16 in.
MAX
: 400
mm
/16
in. 100 mm ≈ 4 in.
200 mm ≈ 7 7/8 in.300 mm ≈ 11 3/4 in.400 mm ≈ 15 3/4 in.
Tools Needed (Not lncluded)
Phillips Screwdriver
Weight Restrictions
If your TV weighs more, this TV stand is NOT compatible.
88lbs/40kg
DO NOT exceed the maximum weight indicated. This TV stand is intended for use only within the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in failure of the TV stand and its accessories, causing possible damage and or injury.
WARNING
P3
(P) x1Support Pillar
(Z) x1Top Cover
(W) x4Foot Pad
(R) x1Gasket with
3 Holes
(Y) x1Plastic Cover
(M) x1TV Plate
(Q) x4M6 Nut
(S) x4M6x40mm
Bolt (T) x4D6.5 Washer
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use damaged or defective parts. lf you require replacement parts, contact our Product Support line at 1-800-556-6806 or customer service at [email protected] (US)/ [email protected] (CA).
• Please note: Not all hardware included in this package will be used.
(O) x1Tempered Glass Base
Supplied Parts and Hardware
Supplied Parts and Hardware for Step 1
Supplied Parts and Hardware for Step 2
Note: The bolt is shown in accordance with the actual size
Note: The bolt is shown in accordance with the actual size
(L) x3M6x25mm Bolt
(V) x15/32in. (4mm)
Allen Key
(V) x15/32in. (4mm)
Allen Key
P4
(A) x4M4x30mm
Bolt
(B) x4M6x15mm
Bolt
(C) x4M6x35mm
Bolt
(D) x4M8x20mm
Bolt
(E) x4M8x35mm
Bolt
(F) x4M8x50mm
Bolt
(G) x4Washer
(K) x2Wire Clip
(H) x8φ8.5x18x2.5mm
Spacer
(I) x4φ8.5x18x10mm
Spacer
(J) x4φ8.5x18x22mm
Spacer
(N) x2TV Bracket
Note: The bolts and spacers are shown in accordance with the actual size
Supplied Part for Step 3
Supplied Parts and Hardware for Step 4
P5
Place foot pads [W] to the frosted side of the tempered glass base [O] in the corners
Step 1-1
Connect the support pillar [P] to tempered glass base [O] Step 1-2
Note: Make sure the side with the wire clip holes on the support pillar faces the back of the stand
Note: The paper side of the gasket with 3 holes [R] should be touched the tempered glass base [O]
Attach the top cover [Z] to the support pillar [P]Secure the support pillar [P] to tempered glass base [O] using plastic cover [Y], gasket with 3 holes [R], bolts [L] and Allen key [V]
(K1) x2Safety Lock
Note: You may need assistance with this step.
Supplied Part and Hardware for Step 5
Step 1 Assemble the Base
O
W
R
OY
P
Z
LV
O
V
LR
Table
P
Front SideBack Side
P6
[Not Included]
Step 2 Connect the TV Plate [M] to Support Pillar [P]
Q
P
TM
SV
Front
Back
Note: There are three choices for height adjustment. You can choose your desired height position while connecting the TV plate [M] to support pillar [P]
Connect TV plate [M] to support pillar [P] using bolts [S], washers [T] and nuts [Q]
Note: Connect the TV plate [M] to the front side of the support pillar [P] with the bump of the TV plate facing back side of the stand.
The First Choice
The First Choice
The Second Choice
The Second Choice
The Third Choice
The Third Choice
Note: You may need assistance with this step.
P7
Only one bolt size fits your TV.
Select TV Bolts
Step 3 Secure the Wire Clips [K] to Support Pillar [P]
Step 4 Secure the TV Brackets [N] to TV
P
K
Too Long Correct CorrectToo Short
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination. We recommend thread engagement by at least 5 turns.-Too short will not hold the TV.-Too long will damage the TV.
Please Note: The provided TV bolts meet most of today’s TVs design. However, some TVs require special bolts which may not be in the hardware bag. In this case we offer our “PSUHP" Universal Hardware Kit which provides a large selection of bolts that can meet the demand of older and unique applications.Please Note: When using the spacers it is important to note that they can be used in multi-layers (meaning stacked). If you have any difficulty understand-ing how to install the TV bolts or spacers, please contact customer service at [email protected] (US)/ [email protected] (CA).
M4 M6 M8
P8
Option B (For Round Back TV)
Option A (For Flat Back TV )
G
A/B/D
H/I(If needed)
G
A/C/E/F
H/I/J
N
Alternate Spacer Setups
Note: Keep the arrow up
Note: Keep the arrow up
AlternateSpacerSetups
CAUTION: Ensure the TV brackets [N] are EQUALLY CENTERED on your TV and securely fastened in place.
Please note: The bolt hole locations on your TV may vary in accordance of the manufacturers design of the TV. We are only illustrating possible locations of the bolt holes.
P9
Alternate Spacer Setups
Alternate Spacer Setups
Option D
For cable interference or inset holes, use spacers [H], [I] and [J] to create extra space between the TV and TV brackets
Spacers may be necessary for 2 holes ONLY.Option C (For TV with A “Bump”)
G
A/C/E/F
H/I/J
A/B/D
G
H/I(If needed)
A/ C/ E/ F
H/ I/ J
GN
N
Note: Keep the arrow up
AlternateSpacerSetups
P10
①
②
Note: Please note, there isno bolt holes in the TV plate
TV brackets are two-height-adjustable. You can choose the proper height.
Step 5-1 Hang the TV with brackets to the TV plate
Step 5-2 Push the bottom of the TV to TV plate
Step 5-3 Insert the safety locks [K1] into the upward facing hooks at the midway to lower part of the TV bracket. Please note this is where the lower part of the TV bracket meets the TV plate. Then tighten the bolts of the safety lock [K1] until the bolts touch the TV plate.
Step 5 Attach TV to the TV Plate [M] and Manage the Wires
The First ChoiceThe Second Choice
K1
“Be gentle”
③
HEAVY! You may need assistance with this step.
Thank you again for choosing this PERLESMITH product!
All of us at PERLESMITH do appreciate your product purchase. We hope that you are as happy with your product as we design-ing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry. Please share your experience of our product with others at www.perlesmith.com/pages/reviews if you are satisfied. If you have any questions please don't hesitate to contact us.
Technical Support: 1-800-556-6806 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info: [email protected] (US）
[email protected] (CA)
Please check
www.perlesmith.com
for more products and
company information.