Basic Cleaning Instructions forTalaris® Dispensers*

Innovative Control Systems1349 Jacobsburg Road • Wind Gap, PA 18091

610.881.8000 • 610.881.8120 – fax • www.washnet.com

* Formerly DeLaRue®

Before You BeginBefore You Begin

• Always turn the power to the unit off • Always turn the power to the unit off before you begin.Have someone available to help you lift • Have someone available to help you lift the bill dispenser if necessary.A lifi d ICS t h i i h l • A qualified ICS technician can help ensure these instructions are followed correctly. C t t ICS f tContact ICS for support.

3/19/2009 2Copyright © 2008 Innovative Control Systems, Inc.

Required ToolsRequired Tools

• Isopropyl rubbing alcohol.Isopropyl rubbing alcohol.– No greater than 70% concentration.

• Q-Tips® type cleaning swabs.Q Tips® type cleaning swabs.• Compressed air.• Paint brush• Paint brush.

– Soft bristled.– 1-inch.

• Cleaning supplies online– http://supplies.talaris.com/

3/19/2009 3Copyright © 2008 Innovative Control Systems, Inc.

Preparing a Work SurfacePreparing a Work Surface

• Prepare a clean solid work surface on • Prepare a clean, solid work surface on which to position the bill dispenser.Work surface should be dry protected • Work surface should be dry, protected and free from debris.D t tt t t th b d • Do not attempt to use the bare ground as a work surface.

3/19/2009 4Copyright © 2008 Innovative Control Systems, Inc.

Removing the DispenserRemoving the Dispenser

• Open side • Open side chamber on unit.Extend tray• Extend tray.

• Access wiring.

3/19/2009 5Copyright © 2008 Innovative Control Systems, Inc.

Removing the DispenserRemoving the Dispenser

• Disconnect power• Disconnect power.

3/19/2009 6Copyright © 2008 Innovative Control Systems, Inc.

Removing the DispenserRemoving the Dispenser

• Disconnect COM• Disconnect COM.

3/19/2009 7Copyright © 2008 Innovative Control Systems, Inc.

Removing the DispenserRemoving the Dispenser

• Disconnect ground• Disconnect ground.

3/19/2009 8Copyright © 2008 Innovative Control Systems, Inc.

Removing the DispenserRemoving the Dispenser

• Unclip harness• Unclip harness.

3/19/2009 9Copyright © 2008 Innovative Control Systems, Inc.

Removing the DispenserRemoving the Dispenser

• Lift dispenser off tray• Lift dispenser off tray.• Place dispenser on secure work surface.

3/19/2009 10Copyright © 2008 Innovative Control Systems, Inc.

Cleaning the Pinch WheelsCleaning the Pinch Wheels

• Remove cassette from dispenser• Remove cassette from dispenser.• Orient dispenser as shown.

Side view

Top view

3/19/2009 11Copyright © 2008 Innovative Control Systems, Inc.

Side view

Cleaning the Pinch WheelsCleaning the Pinch Wheels

• Locate three pinch wheels• Locate three pinch wheels.

3/19/2009 12Copyright © 2008 Innovative Control Systems, Inc.

Cleaning the Pinch WheelsCleaning the Pinch Wheels

• Clean pinch wheels• Clean pinch wheels.– Dust with dry paint brush.

Scrub with alcohol moistened swab– Scrub with alcohol-moistened swab.

TurnScrub

3/19/2009 13Copyright © 2008 Innovative Control Systems, Inc.

Brush

Cleaning the Pinch WheelsCleaning the Pinch Wheels

• Replace swab when dirty• Replace swab when dirty.• Scrub until clean.

R l i f i i h l• Repeat cleaning for remaining wheels.

Getting dirty!3/19/2009 14Copyright © 2008 Innovative Control Systems, Inc.

Getting dirty!

Cleaning the InteriorCleaning the Interior

• Locate yellow handle• Locate yellow handle.• Open door to expose interior.

3/19/2009 15Copyright © 2008 Innovative Control Systems, Inc.

Cleaning the InteriorCleaning the Interior

• Use compressed air• Use compressed air.• Blow-clean interior.

3/19/2009 16Copyright © 2008 Innovative Control Systems, Inc.

Cleaning the ExteriorCleaning the Exterior

• Reorient bill dispenser to horizontal• Reorient bill dispenser to horizontal.• Open top tray.

B h l d h bl l• Brush clean, and then blow clean.

Brush clean Blow clean3/19/2009 17Copyright © 2008 Innovative Control Systems, Inc.

Brush clean Blow clean

Replace Bill DispenserReplace Bill Dispenser

Re-insert cassetteRe insert cassetteReseat & secure bill dispenser on tray.R iReconnect wires.Reclip harness.Close & lock door.TestTest.Repeat cleanings.

E 3 t 4 th d di bill lEvery 3 to 4 months depending on bill volume.3/19/2009 18Copyright © 2008 Innovative Control Systems, Inc.

• Information in this presentation is subject to change without notice. Companies, names and data used in examples within the presentation are fictitious unless names and data used in examples within the presentation are fictitious unless otherwise noted. No part of this presentation may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Innovative Control Systems, Inc.

• ICS is not responsible for damage, bodily harm, loss of business, etc. due to the information contained in this document. Refer to the standard sales agreement and warranty information that came with your ICS product for more details.

• Auto Sentry, Lube Master and Tunnel Master are registered trademarks of Innovative Control Systems, Inc.

• Touch ‘N Clean and Wash Valet are trademarks of Innovative Control Systems, Inc.• DeLaRue is a registered trademark of De la Rue Holdings plc• DeLaRue is a registered trademark of De la Rue Holdings, plc.• Q-Tips is a registered trademark of Unilever Supply Chain, Inc.• Talaris is a registered trademark of Talaris Holdings Limited.

3/19/2009 19Copyright © 2008 Innovative Control Systems, Inc.