tape feeder training rev1.ppt - bpm microsystems

BPM Microsystems, LP

BPM Microsystems Training Course # TAPF-001

Rev. A

ELECTRONIC TAPE FEEDER (Tape and Reel Input)

Teaching Method of the Course

• Covers the fundamentals– More details in BPWin Help

• Step by Step– Broken down to steps– Start with Installation– Continue through complete operation

• Examples– Photos– Diagrams

• Self taught or a taught course.• When complete, trainee should be able to install and

operate the Tape Feeder.

Tools Needed for the Course

• Tape Feeder(s)• Installation Kit, FTAPEIN3X or FTAPEIN4X• Set of SAE Hex Keys (Allen Wrenches)• Reel of Devices to match Feeder

Tape Feeder Training Chapters

1. Identification of parts2. Installing and removing individual Feeders3. Loading and Unloading the Tape Feeder4. Programming the Tape Feeder5. Teaching the Tape Feeder6. Clearing Jams7. Tape Feeder Maintenance8. Installing the Tape Feeder Option

Chapter 1

Identification of Parts

Training Seminar # TAPF-001Revision A

Typical Tape Feeder

Tape Feeder Sizes

Part Number SizeFQUAFDR008 8mmFQUAFDR012 12mmFQUAFDR016 16mmFQUAFDR024 24mmFQUAFDR032 32mmFQUAFDR044 44mmFQUAFDR056 56mm

Size refers to the width of the carrier tape that theTape Feeder can handle.

Tape Feeder Power Base

Chapter 2

Installing and Removing Individual Tape Feeders


1. Align tape feeder with power base.2. Depress locking lever.3. Slide the tape feeder into a groove in the power base

and push the feeder against the wall. CAUTION: Do not twist the feeder!

4. Push down on the rear of the feeder and release the locking lever.

5. Grab the feeder and try to move it side to side. It should stay firmly in place if installed correctly.

6. The green LED should be illuminated if installed correctly.

Installing and Removing Individual Tape Feeders

Chapter 3

Loading and Unloading Tape Feeders


Use the diagram on the following slide to load tape into a tape feeder.

1. Peel back about 2 inches of cover tape.2. Inset the end of the tape into the feeder at the entrance

slot.3. Feed the tape until it contacts the gear teeth.4. Press the red button on the feeder to advance the tape

to the pick point.5. When possible, pull the cover tape back and continue

advancing the tape until about 5 inches of cover tape is peeled off.

6. Feed the cover tape back into the rollers as indicated in the diagram and attach to the spool. Use the slot on the side of the spool.

7. Continue advancing the tape until the first part appears.

8. Refer to chapter 4 to set the Index programming and pocket position programming as required to properly adjust the feeder.

Chapter 4

Programming a Tape Feeder


Index Programming 8 – 32mmSets the Pocket Pitch

1. Simultaneously press the front(red) and rear(black) buttons on the tape feeder to enter programming mode.2. Press the rear button slowly twice, then the front button once to enter index programming mode.3. Use the button sequence in the chart below to program the required pitch.

Index Programming 36 – 44mmSets the Pocket Pitch

1. Simultaneously press the front(red) and rear(black) buttons on the tape feeder. (Both LEDs should go out)2. Press the front button three times slowly. This enters the Pocket Programming Memory Modify Mode.3. Press this button sequence slowly: Rear Front Front Rear Rear Rear Rear Front.4. For 36 mm indexing press: Front Front Front Front Front Front Front Front. For 40 mm indexing press: Front Front Front Front Rear Front Front Rear. For 44 mm indexing press: Front Front Front Front Rear Front Rear Front.5. Simultaneously press the front(red) and rear(black) buttons on the tape feeder. (Both LEDs should go out)6. Press the front button once and the rear button twice to store the sequence in memory.

1. Simultaneously press the front(red) and rear(black) buttons on the tape feeder.2. Press the rear button slowly three times to enter the pocket position programming mode.3. Press and release the front button to advance the tape incrementally. Press and hold the front button to advance the tape rapidly.4. Center the pocket on the etched indicator mark on the tape feeder.5. Press the rear button once to save the position.6. Test the setting by blocking the sensor with your finger. Repeat if necessary.

Pocket Position ProgrammingCenters the pocket in the feeder

Chapter 5

Teaching a Tape Feeder


Start BPWin software and allow the handler to initialize.In the Workflow window, locate the “Sources” box. Give the Tape Feeder teach a valid name. NOTE: The teach name must begin with TAPEIN. In this example, TAPEIN_TSOP48

Go to the main window, menu selection AUTOHANDLER/ TEACH. Select the “TAPEIN” name to bring up the Adjust Nozzle Position window.

Select the correct Pin 1 position according to the Figures (A or B). Use the arrow buttons to position the downward camera or laser pointer over the device, and press OK.

Chapter 6

Clearing Jams


1. Ensure that the carrier tape can exit smoothly. Clear bunched tape if necessary.

2. Check the spent cover tape spool for excessive cover tape. Remove cover tape if necessary.

3. Press the reverse (black) button and see if the tape will back out. Remove excess devices if necessary.

4. Remove the feeder from the base and visually inspect for jammed devices and jammed tape.

5. Cut the tape at the tape entry point or exit point.6. Press the rear button to back out the remaining tape

fragments.7. Reload the tape feeder.

Chapter 7

Tape Feeder Maintenance


Tape Feeders require very little maintenance.There are vary few user serviceable partsinside. BPM Recommends: 1. Periodically clean the adhesive residue off of

the rollers if pressure cover tape is used.2. Check the cover tape drive belt for wear and

replace as necessary.3. Remember that the cover tape removable

spool has left hand threads.

Defective tape feeders will need to be sent toBPM Microsystems, LP for repair. Call technicalsupport for Assistance.

Chapter 8

Installing the Tape Feeder Option


List of installation parts for Tape Feeder Option

FQUAFDR31 – 4” Wide Tape Feeder Power Base

Typical Tape Feeder

Typical Reel Holder Arm

WGRDFINGERCEFDR – Serves as both a finger guard and a bracket to attach the reel holder arm.

WWAVSERIAL2TAPF – Tape Feeder Serial Peripheral Card

Controls the Tape Feeder through a serial peripheral port.

CCHAPLA3XTUBE – SP Card Mounting Plate

Used on 3x00 systems as a safe way to mount the SPcard to the inside of the machine.

WCAB4XTAPFPWR – Power Cable

Connects the tape feeder base to the SP card.

WCABSHUTLPWRCOM – Communication Cable

Connects the SP card to the control port.

Assorted Hardware

Screws, nuts, washers, tie wraps, and anchors used to install the upgrade hardware.

4x00 Tape Feeder Installation-Hardware-

Important: Power the system down and observe ESD precautions when handling electronic circuit boards.

1. Mount the 4” tape Feeder Base to the table top between sites 5 and 9. The exact position is unimportant, as long as the downward camera can see the pick point, and the feeder base is square to the tape top. Drill and tap ¼ - 20 hole(s) if necessary.

2. Mount the 4” Finger guard to the table top behind the feeder base. The guard will hang off the back of the machine.

3. Mount the Tape Feeder SP card to the CHARPLA4XCOMM SP card mounting plate inside the logic rack. Use any open position.

4. Connect the WCAB4XTAPFPWR cable 9 pin connector to J6 of the Serial Peripheral card.5. Run the cable through the machine and out of the diagonal slot behind site 5.6. Connect the 4 pin connector to the T/F base.7. Connect the two pin connector to the empty carrier take-up reel option (if present).8. Connect one RJ12 connector of the WCABSHUTLPWRCOM cable to J1 on the SP card.9. Connect the other RJ12 connector to any unused port on the Interface board also located in the Logic card rack.10. Use the anchors and tie wraps to complete the hardware installation.

4x00 Installation Diagram

Tape Feeder installed with Reel holder arm attached to the finger guard. A rear metal panel (not shown) covers the open area around the finger guard.

Empty Carrier Tape Take-up Reel system

3x00 Tape Feeder Installation-Hardware-

Important: Power the system down and observe ESD precautions when handling electronic circuit boards.

1. Mount the 4” tape Feeder Base to the table top. The exact position is unimportant, as long as the downward camera can see the pick point, and the feeder base is square to the tape top. The feeder is usually mounted in the left bay on top of the tape loader mounting plate. The feeder base can be mounted directly to the table top.

2. Mount the finger guard to the mounting plate behind the feeder base.

3. Screw the SP card to the SP card mounting plate.4. Bolt the mounting plate and SP card assembly to the inside of the machine. Drill and tape a hole if necessary.5. Connect the WCAB4XTAPFPWR cable 9 pin connector to J6 of the Serial Peripheral card.6. Run the other end of the cable up through the slot in the table top closest to the base.7. Connect the 4 pin connector to the base.8. Connect the two pin connector to the empty carrier take-up reel option (if present).9. Connect one RJ12 connector of the WCABSHUTLPWRCOM cable to J1 on the SP card.10. Connect the other RJ12 connector to any unused port on the backplane. 11. Use the anchors and tie wraps to complete the hardware installation.

Chapter 9

Tape Feeder Upgrade Kit (FUPGTPFDRD-W)

BPDOS to BPWin Upgrade, 4x00 systems only

Bill Of Materials:(1) WWAVSERIAL2TAPF – T/F Serial Peripheral Card(2) CCHAPLA3XTUBE – SP Card Mounting Plate(3) WCAB4XTAPFPWR – Power Cable(4) WCABSHUTLPWRCOM – Communication Cable(5) Assorted Hardware

FUPGTPFDRD-W

Installing the DOS to Windows Upgrade Kit

Refer to Chapter 8 for installation instructions.

Review Questions

Questions: Yes, No answers, 2 minutes1. What determines the size of a tape feeder?2. What is a valid name for a tape feeder

teach?3. What is “pitch”?4. How can you determine if a tape feeder is

installed correctly in the power base?

Chapter 5: Turning On and Off

Answers to Review Questions

1. What determines the size of a tape feeder?- The width of the carrier tape.2. What is a valid name for a tape feeder teach?- The name begins with TAPEIN.3. What is “pitch”?- The distance between centers of tape pockets.4. How can you determine if a tape feeder is installed

correctly in the power base?- The green LED will be on, and you cannot move the

feeder.

Chapter 5: Turning On and Off

This completes the Tape Feeder training class.

tape feeder training rev1.ppt - bpm microsystems

Documents