Oth

ers

Mai

nte

nan

ceO

per

atio

ns

Pre

par

atio

ns

Bef

ore

Usi

ng

OWNER’S MANUAL

DATA PROJECTORTDP-T250

Bef

ore

Usi

ng

32

SAFETY PRECAUTIONSBefore Using

The lightning flash with arrowhead symbol, within an equilateral triangle, is intendedto alert the user to the presence of uninsulated "dangerous voltage" within the product'senclosure that may be of sufficient magnitude to constitute a risk of electric shock topersons.

The exclamation point within an equilateral triangle is intended to alert the user to thepresence of important operating and maintenance (servicing) instructions in theliterature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSETHIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGESARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET.REFER SERVICING TO QUALIFIED PERSONNEL ONLY.

WARNING: Handling the cord on this product or cords associated with accessories sold withthis product, will expose you to lead, a chemical known to the State of Californiato cause birth defects or other reproductive harm. Wash hands after handling.

WARNING: This [product] contains mercury. Disposal of mercury may be regulated due toenvironmental considerations. For disposal or recycling information, pleasecontact your local authorities or the Electronic Industries Alliance: www.eiae.org.

USA only

MODEL NAME: TDP-T250FCC Radio Frequency Interference StatementNote: This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designedto provide reasonable protection against harmful interference when the equipmentis operated in a commercial environment. This equipment generates, uses, andcan radiates radio frequency energy and, if not installed and used in accordancewith the instruction manual, may cause harmful interference to radiocommunications. Operation of this equipment in a residential area is likely tocause harmful interference in which case the user will be required to correct theinterference at his own expense.

WARNING: Changes or modifications made to this equipment, not expressly approved byToshiba, or parties authorized by Toshiba, could void the user’s authority to operatethe equipment.

Notice: This Class A digital apparatus complies with Canadian ICES-003. Cet appareilnumérique de la classe A est conforme à la norme NMB-003 du Canada.

WARNING: This is a Class A product. In a domestic environment this product may causeradio interference in which case the user may be required to take adequatemeasures.

USA only

USA only

USA only

CANADA only

Bef

ore

Usi

ng

54

5. HeatThe product should be situatedaway from heat sources such asradiators, heat registers, stoves, orother products (includingamplifiers) that produce heat.

6. Water and MoistureDo not use this product near water.- for example, near a bath tub,wash bowl, kitchen sink, or laundrytub; in a wet basement; or near aswimming pool and the like.

7. CleaningUnplug this product from the walloutlet before cleaning. Do not useliquid cleaners or aerosol cleaners.Use a soft cloth for cleaning.

8. Power-Cord ProtectionPower-supply cords should berouted so that they are not likely tobe walked on or pinched by itemsplaced upon or against them,paying particular attention to cordsat plugs, convenience receptacles,and the point where they exit fromthe product.

9. OverloadingDo not overload wall outlets;extension cords, or integralconvenience receptacles as thiscan result in a risk of fire orelectric shock.

IMPORTANT SAFETY INSTRUCTIONSCAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND

INSTRUCTIONS GIVEN IN THIS OWNER'S MANUAL AND THOSEMARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTUREREFERENCE.

This set has been designed and manufactured to assure personal safety. Improper use canresult in electric shock or fire hazard. The safeguards incorporated in this unit will protect youif you observe the following procedures for installation, use and servicing. This unit is fullytransistorized and does not contain any parts that can be repaired by the user.DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TODANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICEPERSONNEL ONLY.

1. Read Owner's ManualAfter unpacking this product, readthe owner's manual carefully, andfollow all the operating and otherinstructions.

2. Power SourcesThis product should be operatedonly from the type of power sourceindicated on the marking label.If you are not sure of the type ofpower supply to your home,consult your product dealer orlocal power company.For products intended to operatefrom battery power, or othersources, refer to the operatinginstructions.

3. Source of LightDo not look into the lens while thelamp is on. The strong light fromthe lamp may cause damage toyour eyes or sight.

4. VentilationOpenings in the cabinet areprovided for ventilation and toensure reliable operation of theproduct and to protect it fromoverheating, and these openingsmust not be blocked or covered.The openings should never beblocked by placing the product ona bed, sofa, rug or other similarsurface. This product should notbe placed in a built-in installationsuch as a bookcase or rack unlessproper ventilation is provided orthe manufacturer's instructionshave been adhered to.

Bef

ore

Usi

ng

76

IMPORTANT SAFETY INSTRUCTIONS (Continued)

15. AccessoriesDo not place this product on anunstable cart, stand, tripod,bracket, or table. The product mayfall, causing serious injury to achild or adult, and serious damageto the product. A product and cartcombination should be moved withcare. Quick stops, excessiveforce, and uneven surfaces maycause the product and cartcombination to overturn.

S3125A

16. Damage Requiring ServiceUnplug this product from the walloutlet and refer servicing toqualified service personnel underthe following conditions:

a) When the power-supply cord orplug is damaged.

b) If liquid has been spilled, orobjects have fallen into theproduct.

c) If the product has been exposed torain or water.

d) If the product does not operatenormally by following the operatinginstructions. Adjust only thosecontrols that are covered by theoperating instructions as animproper adjustment of othercontrols may result in damage andwill often require extensive work bya qualified technician to restorethe product to its normaloperation.

e) If the product has been dropped ordamaged in any way.

f) When the product exhibits adistinct change in performance -this indicates a need for service.

17. If glass components,including lens and lamp,should break, contact yourdealer for repair service.This product incorporates glasscomponents, including a lens anda lamp. If such parts shouldbreak, please handle with care toavoid injury and contact yourdealer for repair service. Thebroken pieces of glass may causeto injury. In the unlikely event ofthe lamp rupturing, thoroughlyclean the area around theprojector and discard any edibleitems placed in that area.

18. ServicingDo not attempt to service thisproduct yourself as opening orremoving covers may expose youto dangerous voltage or otherhazards. Refer all servicing toqualified service personnel.

10. Lightning stormsFor added protection for thisproduct during storm, or when it isleft unattended and unused forlong periods of time, unplug it fromthe wall outlet. This will preventdamage to the product due tolightning and power-line surges.However, while it is thundering orlightning, do not touch theapparatus and any connectedcable and/or equipment.This will prevent you fromreceiving the electric shock by anelectric surge.

11. Object and Liquid EntryNever push objects of any kindinto this product through openingsas they may touch dangerousvoltage points or short-out partsthat could result in a fire or electricshock. Never spill liquid of anykind on the product.

12. Do not place the productverticallyDo not use the product in theupright position to project thepictures at the ceiling, or any othervertical positions. It may fall downand dangerous.

13. Stack InhibitedDo not stack other equipment onthis product or do not place thisproduct on the other equipment.Top and bottom plates of thisproduct develops heat and maygive some undesirable damage toother unit.

14. AttachmentsDo not use attachments notrecommended by the productmanufacturer as they may causehazards.

Bef

ore

Usi

ng

8 9

If your line voltage is 220 to 240V, use one of the following types of cable.

Plugconfiguration Plug type

Australian240V10A

North American240V15A

Switzerland240V6A

Line voltage

EURO

UK

220 – 240V

220 – 240V

200 – 240V

200 – 240V

200 – 240V

Plugconfiguration Plug type Line voltage

Use a 5A fuse which is approved by ASTA or BSI to BSI362.Always replace the fuse cover after changing the fuse.

IMPORTANT PRECAUTIONSSave Original Packing Materials

The original shipping carton and packing materials will come in handy if you ever have toship your projector. For maximum protection, repack the set as it was originally packed atthe factory.

Moisture CondensationNever operate this unit immediately after moving it from a cold location to a warm location.When the unit is exposed to such a change in temperature, moisture may condense onthe crucial internal parts. To prevent the unit from possible damage, do not use the unit forat least 2 hours when there is an extreme or sudden change in temperature.

Place and Manner of Installation• Do not place in hot locations, such as near heating equipment. Doing so could cause

malfunction, and shorten the life of the projector.• Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts,

shortening their lives, and darkening the screen.• Do not use this product in the upright position or tilt it up or down by more than 20° from

level. Doing so may cause a failure or shorten the life of the product.• Using this instrument near a TV or radio may cause interference to the images or audio

sound. If this happens, move it away from the TV or radio.• Moving the projector from a low-temperature room to a high-temperature room may

cause condensation on the lens or internal parts in the instrument. If you continue to useit in that situation, the malfunction may result. Ensure to wait until the condensationnaturally disappears.

• In a high altitude location where air is thin, cooling efficiency is reduced so use theprojector with [Fan mode] set to [High]. p.45

POWER SUPPLY CORD SELECTION19. Replacement Parts

When replacement parts arerequired, be sure the servicetechnician has used replacementparts specified by themanufacturer or have the samecharacteristics as the original part.Unauthorized substitutions mayresult in fire, electric shock, orother hazards.(Replacement of the lamp onlyshould be made by users.)

20. Safety CheckUpon completion of any service orrepairs to this product, ask theservice technician to performsafety checks to determine thatthe product is in proper operatingcondition.

21. Do not leave thermal-paper documents or easilydeformed items on top ofthe unit or near the airexhaust for long periodsof time.The heat from the unit could erasethe information on the thermalpaper, or cause deformation orwarping.

IMPORTANT SAFETY INSTRUCTIONS (Continued)

22. Do not use the product ina closed installation state.Do not place the product in a boxor in any other closed installationstate. Otherwise it may overheat.This could result in a risk of fire.

23. Do not look into the laserlight source of the remotecontrol or direct the laserpointer toward a person ora mirror.The laser beam may causedamage to the eyes or sight.

Bef

ore

Usi

ng

10 11

EXEMPTION CLAUSES• Toshiba Corporation bears no responsibility in the case of damages arising from natural

disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation,operation, theft or mischief by third parties, other accidents, or use under abnormalconditions including erroneous or improper operation and other problems.

• Toshiba Corporation bears no responsibility for incidental damages (lost profit, workinterruption, corruption or loss of the memory contents, etc.) arising from the use of or theinability to use this unit.

• Toshiba Corporation accepts no liability whatsoever for any damages arising from nothaving followed the descriptions in this Instruction Manual.

• Toshiba Corporation accepts no liability whatsoever for any damages arising frommalfunctions arising from combination with equipment or software that is not related toToshiba Corporation.

CopyrightsShowing or transmitting commercial imaging software or broadcast or cable-broad castingprograms with the purpose of other than the personal and private viewing, includingmodifying images using the freeze, resize, PIP, or SPLIT screen functions, or displaying withthe varying aspect ratio of the images, could violate the direct or indirect copyrights of theimaging software or broadcast program, etc., if done without first consulting with thecopyright holder. For this reason, please take appropriate measures before performing oneof the actions listed above, including obtaining a license from the copyright holder.

DisposalThis product contains substances which are harmful to humans and the environment.• Solder used in the internal parts contains the lead.• The lamp contains inorganic mercury.Please dispose of this product or used lamps in accordance with local regulations.

Trademarks• VGA, SVGA, XGA, SXGA, UXGA are trademarks or registered trademarks of

International Business Machines Corporation.• Digital Light Processing, Digital Micromirror Device and DMD are trademakes of Texas

Instruments.• Macintosh is a registered trademark of Apple Computer, Inc.• Windows is a registered trademark of Microsoft Corporation in the U.S. and other countries.• Adobe is a registered trademark and Acrobat Reader is a trademark of Adobe Systems

Incorporated.

Notational Conventions Used in This Manual• References to pages with related information are annotated as follows.

For example, if making a reference to page 36: p.36

• The illustrations in this document are for reference purposes only and may not reflectyour package exactly.

REMOTE CONTROL BATTERIESCaution• Never throw batteries into a fire.

Notes• Be sure to use AAA size batteries.• Dispose of batteries in a designated disposal area.• Attention should be drawn to the environmental aspects of battery disposal.• Do not mix different battery types or combine used batteries with new ones.• If the remote control does not operate correctly, or if the operating range becomes

reduced, replace both batteries with new ones.• If the batteries are dead or if you will not be using the remote control for a long time,

remove the batteries to prevent battery acid from leaking into the battery compartment.Using the batteries improperly may cause them to explode or leak and lead to burn or injury. Ifbattery-leaking fluid contacts skin, wash the fluid off immediately with clean water and consult adoctor. If the fluid is spilt on an instrument, avoid contact and wipe it off using tissue paper.(Dispose of the used tissue paper as flammable garbage after moistening with water.)

IMPORTANT PRECAUTIONS (Continued)

Avoid Volatile LiquidDo not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber orplastic products touching the unit for a long time. They will leave marks on the finish.If cleaning with a chemically saturated cloth, be sure to follow the product's precautions.

In the spaces provided below, record the Model and Serial No. located at the bottom of yourprojector.Model No. Serial No.

Retain this information for future reference.

OTHER CAUTIONS AND INFORMATIONS

Bef

ore

Usi

ng

1312

CONTENTS

Before UsingSAFETY PRECAUTIONS .................................................................................. 2IMPORTANT SAFETY INSTRUCTIONS ........................................................... 4POWER SUPPLY CORD SELECTION .............................................................. 9IMPORTANT PRECAUTIONS ........................................................................... 9EXEMPTION CLAUSES .................................................................................... 10OTHER CAUTIONS AND INFORMATIONS ...................................................... 11REMOTE CONTROL BATTERIES .................................................................... 11CONTENTS ....................................................................................................... 12

PreparationsChecking the package contents ......................................................................... 14Names of each part on the main unit ................................................................. 15Names of each part on the control panel and remote control ............................ 16Label locations ................................................................................................... 17Parts on the rear panel ...................................................................................... 18Preparing and using the remote control ............................................................. 20Operating a computer using the remote control ................................................ 21Placement .......................................................................................................... 22Connection ......................................................................................................... 24

OperationsTurning the power on and off ............................................................................. 26Basic operations ................................................................................................ 28Using handy features ......................................................................................... 30

Using auto setting ........................................................................................... 30Correcting the keystone distortion .................................................................. 30Resizing image ............................................................................................... 31Cutting off the picture and sound temporarily (Mute) ..................................... 32Changing picture mode .................................................................................. 33Changing screen size ..................................................................................... 33Freezing the image (Freeze) .......................................................................... 33Display a sub screen (PIP function) ................................................................ 34Sub screen setting .......................................................................................... 34Displaying two screens (SPLIT function) ........................................................ 35SPLIT function setting .................................................................................... 35Screen combination of PIP and SPLIT functions ........................................... 36Password function .......................................................................................... 36

Using the menus ................................................................................................ 38How to use the menus .................................................................................... 38The image adjustment menu .......................................................................... 39The display setting menu ................................................................................ 41The default setting menu ................................................................................ 44The control setting menu ................................................................................ 46Displaying Information (Status display) .......................................................... 48

MaintenanceAbout lamp ......................................................................................................... 49Lamp replacement ............................................................................................. 49Lens and main unit cleaning .............................................................................. 52

OthersTrouble indications ............................................................................................. 53Before calling service personnel ........................................................................ 54Specifications ..................................................................................................... 55

List of general specifications .......................................................................... 55Separately sold product .................................................................................. 55List of supported signals (RGB signals) ......................................................... 56List of supported signals (Y/PB/PR signals) .................................................... 57List of supported signals (Video, S-Video signals) ......................................... 57Pin assignment of COMPUTER-2 & MONITOR terminals ............................. 57Pin assignment of DVI-I terminal .................................................................... 58CONTROL terminal ........................................................................................ 59

1514

Pre

par

atio

ns

The Supplied CD-ROMThe supplied CD-ROM contains an owner’s manual, including information not available forthe printed Owner’s manual (Getting started) and Acrobat® Reader™ to view the manual.

Installing Acrobat® Reader™Windows®: Run the CD-ROM, select the Reader/English folder, and run ar500enu.exe.Follow the on-screen instructions.Macintosh: Run the CD-ROM, select the Reader/English folder, and run ReaderInstaller. Follow the on-screen instructions to install the software.

Viewing the manualRun the CD-ROM and double-click on Start.pdf. Acrobat® Reader™ launches, and themenu screen of the Owner’s manual appears. Click on your language. The Owner’sManual cover and list of bookmarks appear. Click on a bookmark title to view thatsection of the manual. Click on p. to view a reference page with related information.See the Help menu for more information about Acrobat® Reader™.

(1) Remote control (2) LR03 (SIZE AAA) batteries for remote

control (2) (3) CD-ROM (4) Owner’s Manual (5) RGB cable (3m)

Please make sure that the following items are included in the box, along with the main unit.If any item is missing, please contact the store immediately where you purchased theproduct.

(1) (5) (9)

(2) (6)

(3) (7) (10)

(4) (8)

Checking the package contentsPreparations

NoteThe shape and number of supplied power cords vary depending on the product destination.

(6) Power cord (See note)

(7) Audio cable (for computer input) (8) Audio cable (for video input) (9) Carrying bag (10) Mouse remote control receiver

Names of each part on the main unit

Back Front

(10) (11)

(9)

(12)

(8)

(13)

(6) (1)(4) (3) (2)(5)(7)

(11) (14) (15)

Name : Function

(1) Lens : Projects expanded image.(2) Infrared remote sensor : Senses commands from the remote control. p.20

(3) Foot adjuster release button : Press to set up or stow the foot adjuster. p.29

(4) Antitheft lock hole : Attach a safety cable or any other antitheft device.(5) Air exhaust : Expels air that has grown hot inside the projector.(6) Control panel : Operates the projector. p.16

(7) Lamp cover : Remove to replace lamp. p.50

(8) Zooming lever : Adjusts screen size. p.29

(9) Focusing lever : Adjusts screen focus. p.29

(10) Air intake : Draws in air from outside the projector.(11) Speaker : Outputs audio sound.(12) Rear panel : Connects external devices. p.18

(13) Tilt adjuster : Adjusts the projector’s horizontal tilt. p.29

(14) Handle : Hold to carry the projector.(15) Foot adjuster : Adjusts the vertical projection angle. p.29

1716

Pre

par

atio

ns

Names of each part on the control panel and remote controlControl panel Remote Control

Name : Main Function

Control panel(1) ENTER button : Accepts the selected mode.(2) MENU button : Displays menus. p.38(3) KEYSTONE button : Adjusts keystone distortion. p.30

(4) ON/STANDBY button : Turns the power on/off (standby). p.26

(5) ON/STANDBY indicator : Displays whether power is on or off. p.26

(6) INPUT button : Selects input. p.28(7) RETURN button : Goes back one screen.(8) Selection button : Menu selections and adjustments, volume control, etc.

p.38

(9) LAMP indicator : Displays lamp mode. p.27(10) TEMP indicator : Lights when internal temperature too high. p.53(11) FAN indicator : Displays cooling fan mode. p.53

Remote control(1) ENTER button : Accepts the selected mode.(2) MENU button : Displays menus. p.38

(3) KEYSTONE button : Adjusts keystone distortion. p.30

(4) ON/STANDBY button : Turns the power on/off (standby). p.26(6) INPUT button : Selects input. p.28

(7) RETURN button : Goes back one screen.(8) Selection button : Menu selections and adjustments, volume control, etc.

p.38(12) LASER button : Shows a laser pointer.

(1)

(2)

(3)

(4)(5)

(6)

(7)

(8)

(9) (10) (11)

(4)(6) (3)(13)

(2)

(1)

(12)

(28)(16)(17)(18)(19)(20)

(21)

(29)(8)(7)

(27)(26)(25)(24)

(14)

(23)(22)

(30)

(15)

Remote control transmitterLaser light

source

Battery cover

Warning label

CAUTION• Do not look into the laser light

source of the remote control ordirect the laser pointer toward aperson or a mirror.

• Handling and adjusting other thandescribed here may lead todangerous exposure to laser.

Name : Main Function

(13) AUTO SET button : Sets up analog input from computer. p.30(14) Laser indicator : Lights when laser is on.(15) Mouse control button : Controls a mouse pointer. p.21

(16) PAGE+ button : Proceeds PowerPoint® slides. p.21

(17) MUTE button : Cuts off the picture and sound temporarily. p.32(18) FREEZE button : Pauses image. p.33

(19) SPLIT button : Displays two screens. p.35

(20) Ten-Key button : Use as a ten-key pad with wired LAN, from whichnumbers and characters can be entered. p.47

(21) Remote control ON/OFF switch : Switches on/off the remote control. p.20

(22) SWAP button : Swaps the main screen and the sub screen in PIPmode, or swaps the two screens in SPLIT mode. p.34

(23) PIP button : Displays the sub screen. p.34(24) PICTURE button : Changes image mode. p.33

(25) SCREEN SIZE button : Changes screen size. p.33

(26) RESIZE button : Enlarges image. p.31

(27) PAGE- button : Goes back PowerPoint® slides. p.21(28) R-CLICK button : Functions as right-click of a mouse. p.21(29) L-CLICK button : Functions as left-click of a mouse. p.21

(30) Remote control code switch : Sets the code of remote control to that of the projector.(inside the battery cover) p.45

Note• For the remainder of this manual, buttons are referred to as follows:

Selection buttons ⇒ ; ENTER button ⇒

Label locations

Caution – use of controls or adjustments or performance of procedures other thanthose specified herein may result in hazardous radiation exposure.

1918

Pre

par

atio

ns

Parts on the rear panel(4) (6)(3)(2) (5) (7)

(9) (10)

(1)

(11)(8)

Name : Main Function

(9) VIDEO IN terminalS-VIDEO : Input S video signals from video equipment.

AUDIO (L/R) : Input audio signals from video equipment.VIDEO : Input video signals from video equipment.

AUDIO (L/R) : Input audio signals from video equipment.(10) AC IN socket : Connect the supplied power cord here.(11) Main power switch : AC power line ON (standby)/OFF.

Name : Main Function

(1) Infrared remote sensor : Senses commands from the remote control. p.20

(2) CONTROL terminalLAN : Connects a network cable.

RS232C : When operating the projector via a computer, connectthis to the controlling computer’s RS-232C port. p.59

(3) COMPUTER (Y/PB/PR) 2 IN terminalRGB : Input analog RGB signal from a computer or other

source, or a component video signal (Y/PB/PR) fromvideo equipment.

AUDIO : Input audio signals.(4) COMPUTER (Y/PB/PR) 1 IN terminal

DVI-I : Input analog or digital RGB signal from a computer, ora component video signal (Y/PB/PR) from videoequipment.

AUDIO : Input audio signals.(5) MONITOR terminal : Connect to a computer display, etc.(6) AUDIO OUT terminal : Outputs audio signals.(7) COMPUTER (Y/PB/PR) 3 IN terminal

BNC : Input G/B/R/HD/VD signal from a computer, or acomponent video signal (Y/PB/PR) from videoequipment.

AUDIO : Input audio signals.(8) CAMERA POWER terminal : DC power supply terminal (+15 V). Reserved for future

use.

2120

Pre

par

atio

ns

Operating the remotecontrol

Turn on the ON/OFF switch of theremote control.Point toward the projector’sinfrared remote sensor, and press abutton on the remote control.• Operating the projector from the front

Approx. 15°

Approx. 5m

• Operating the projector from the rear

Approx. 15°

Approx. 5m

Loading dry-cell batteriesinto the remote control

q Remove the battery cover.

w Insert the dry-cell batteries.Be sure to align the plus and minusends of the batteries properly.

Two batteries (LR03, SIZE AAA) areused.

e Replace the battery cover.

Dry-cell batteries• Before using the batteries, be sure to observe the Safety Precautions described in

previous pages.• Remove batteries from remote control when not using for extended periods.• If the remote control stops working, or if its range decreases, replace all the batteries with

new ones.

The remote control• Turn off the ON/OFF switch of the remote control when not in use or to store in baggage.• The remote control may fail to operate if the infrared remote sensor is exposed to bright

sunlight or fluorescent lighting.• Do not drop or bang.• Do not leave in hot or humid locations.• Do not get wet or place on top of wet objects.• Do not take apart.• In rare cases, ambient conditions could impede the operation of the remote control. If this

happens, point the remote control at the main unit again, and repeat the operation.

Preparing and using the remote control Operating a computer using the remote controlA computer can be operated using the projector’s remote control. This function is availableon any computer with the Windows 98/98SE, Windows Me, Windows 2000, or Windows XPOS, that is equipped with a USB port which can support USB1.1 (The mouse remotecontrol receiver is also supported on OS 9 or OS X for the Macintosh). However, pleasenote that Toshiba does not guarantee the operation of all computers.

1 Connecting a computerConnect the mouse remote control receiver (supplied) to a computer.

Mouse remote control receiver

To USB port

2 Operating a computerOperate remote control’s buttons towards the mouse remote control receiver. Moving the mouse pointer

Press the mouse control button in the direction you wish the mouse pointer to move,then press.

To left clickPress the L-CLICK button.

To right clickPress the R-CLICK button.

To drag and dropHolding down the L-CLICK button, move the mouse control button until the mousepointer is over the desired location, then release the L-CLICK button.

Using the computer’s page up [↑] and down [↓] functionPress the PAGE+ and PAGE- buttons to switch PowerPoint® slides.

The remote control may fail to operateif the mouse remote control receiver isexposed to bright sunlight orfluorescent lighting.In such a case, change position ordirection of the mouse remote controlreceiver and retry.

Mouse control

Remote Control Front Remote Control Rear

PAGE – PAGE +

R-CLICK

L-CLICK

2322

Pre

par

atio

ns

Placement StylesAs shown in the figures below, this device can be placed in 4 different styles.The factory setting is “floor-mounted front projection.” Set the [Projection mode] in theDefault setting menu p.44 , in accordance with your needs.

Placement

WARNING• Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit.

Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thusresulting in injury.

• If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting theprojector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge.Improper mounting could cause the projector to fall, resulting in an accident.

• If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Leteveryone involved with the use of the projector know that fact.

Floor-mounted front projection

Floor-mounted rear projection

Ceiling-mounted front projection

Ceiling-mounted rear projection

Projection Distance and SizeUse the figures, tables, and formulas below to determine the projection size and projectiondistance. (Projection sizes are approximate values for full-size picture with no keystoneadjustment.)

Screen As seen from above

As seen from the side

a is the distance (m) between the lens and the screen, and corresponds to a range of1.29 m to 12.10 m. H is the height from the image bottom to the center of the lens.

90°

a

90°H

Lens center

a (min length) = projection size (inches) – 1.4596

29.888

a (max length) = projection size (inches) – 1.2084

24.744

projectionprojection distance a (m)

height (H)min length max lengthsize (inches)

(zooming max) (zooming min)(cm)

33 – 1.29 6.840 1.29 1.57 8.260 1.96 2.38 12.380 2.63 3.18 16.5

100 3.30 3.99 20.6150 4.97 6.01 30.9200 6.64 8.03 41.1250 8.32 10.05 51.4300 9.99 12.08 61.7

2524

Pre

par

atio

ns

Before connection• Read the owner’s manual of the device you are connecting to the projector.• Some types of computer cannot be used or connected to this projector.

Check for an RGB output terminal, supported signal p.56 , etc.• Turn off the power of both devices before connecting.• The figures are sample connections.

Connecting with computers

Notes• Signals are output from MONITOR OUT terminal even in standby mode. From AUDIO OUT terminal, no audio signal is output.• Moving pictures played back on computers using DVD software may appear unnatural if it

is projected with this projector, but it is not a malfunction.

Connection

Notes• When an AUDIO OUT terminal is connected, sound is not output from the projector

speaker.• Output volume of AUDIO OUT terminal can be adjusted by the VOL button.

Connecting with AV equipment

p.59

Computer (for control) ComputerMonitor

Speaker withbuilt-in amplifier

To RS-232Cterminal

To DVI output

DVI cable(not supplied) Audio cable

(not supplied)

To audio output To audioinput

Audio cable(notsupplied)

Control cable

RGB cable(supplied)

Audio cable(not supplied)

To audiooutput

To RGB output

Computer

Monitor cable MiniD-sub 15P-BNC(not supplied)

To RGB output

To audiooutput

Audio cable (not supplied)

Computer

DVD video recorder, etc.DVD video recorder,

DVD player, etc.

Audio amplifier, etc.

DVD video recorder, etc.Video recorder,DVD player, etc.

Video recorder, etc.

To DVI output Conversionadapter BNC-pin(not supplied)To Y/CB/CR outputGreen (Y)/Blue(CB)/Red (CR)

DVI cable-29 pin(not supplied)

Audio cable(not supplied)

To audio outputWhite (L)/Red (R)

Audio cable(not supplied)

Monitor cable MiniD-sub 15P-BNC(not supplied)

To audio outputWhite (L)/Red (R)

Audio cable(not supplied)

To audio inputWhite (L)/Red (R)

Audio cable(not supplied)

To audio outputWhite (L)/Red (R)

To audio outputWhite (L)/Red (R)

To audio outputWhite (L)/Red (R)

Conversion adapterBNC-pin (not supplied)Green (Y)/Blue (CB)/Red (CR)

Component cable(not supplied)

To Y/CB/CR outputGreen (Y)/Blue (CB)/Red (CR)

AV cable(not supplied)Video cable

(not supplied)

S-video cable(not supplied)

To S-videooutput

To video output

• The MONITOR OUT terminal outputs analog RGB signals or component video signals (Y/PB/PR) from the COMPUTER 1 IN, COMPUTER 2 IN, or from the COMPUTER 3 INterminal as selected with the INPUT button. If no input is selected, the MONITOR OUTterminal outputs the input signals last selected among the COMPUTER 1 IN, COMPUTER2 IN, and the COMPUTER 3 IN terminals. (Digital RGB signals are not output.)

• A computer monitor usually cannot accept Y/PB/PR signals correctly.

27

Op

erat

ion

s

26

• The first time you use the projector after purchase, after the start-up screen disappears,the start menu is displayed p.28 .

• You can disable the beep sound in the Display setting menu p.41 .• When [Key lock] is [On], the operation buttons of the projector do not work p.44 .• When [Password] is [On], the start-up screen is displayed after the Password entry

screen disappears p.44 .

Turning the power off

1 Press the ON/STANDBY button.A message appears on the screen, confirming that you wish to shut off the power. Thismessage will disappear after a moment. (This operation is no longer valid after themessage disappears.)

2 Press the ON/STANDBY button again.A beep sound is made (if the beep sound is set to [On]) and the screen turns off, butthe internal cooling fan continues to operate for a short while. Then, the projector goesinto standby mode.

When cooling lamp During internal cooling After cooling complete

A B C

A During cooling, the LAMP indicator flashes. In this state, the power cannot beturned back on.If you are in a hurry, there is no problem with unplugging the power cord orturning off the main power switch in this state.

B After the LAMP indicator goes off, the FAN indicator keeps lighted and thecooling fan continues to operate for a short while, in order to expel excessinternal heat.

C In standby mode

Note• The projector consumes about 16W of power in standby. We recommend that you unplug

the power cord or turn off the main power switch if you will not be using the projector foran extended period.

PRECAUTION• If the power cord is unplugged before cooling is complete, give the lamp time (about 5

minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light, andits lifetime will be shortened.

Turning the power on and offOperations

Connecting the power cord1 Insert the power cord connector into

the AC IN socket of the projector.

2 Insert the power cord plug into awall or other power outlet.

Removing the lens coverBe sure to remove the lens cover when the power isturned on. If it is left on, it could become deformed dueto heat.

Turning the power on1 Turn on the main power

switch.The ON/STANDBY indicator willchange to orange, indicating standbymode.

2 Press the ON/STANDBYbutton.The power turns on with a beep sound(if the beep sound is set to [On]), andthe following 3 green indicators light:ON/STANDBY, LAMP, and FAN. After amoment, the start-up screen appears.

CAUTION• Do not look into the lens while the lamp is on. The strong light from the lamp may cause

damage to your eyes or sight.• Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.• Do not place your hands, face, or other objects near the air exhaust. Doing so could cause

burns, deform/break the object.

Power cord connector(Supplied)

Start-up screenControl panel

RemoteControl

Notes• The start-up screen will disappear after a moment. You can dismiss the start-up screen

before this by performing any operation. You can also configure the start-up screen not toappear via the Display setting menu p.41 .

29

Op

erat

ion

s

28

5 Projector placement angle adjustmentsThe placement angle and the height of the projected image can be adjusted by the footadjuster.

q Lift up the front of the projector tothe desired angle, then press thefoot adjuster release button.The foot adjuster extends. Release thebutton to lock the position.

w To fine adjust the angle, twist thefoot adjuster.

e To adjust the horizontal angle, usethe tilt adjuster.

To stow the foot adjuster, hold up the projectorwhile pressing the foot adjuster release button,then slowly lower the projector.

6 Adjusting the screen size and focusq Use the zooming lever to adjust the screen size.

w Use the focusing lever to adjust the focus.

7 Adjusting the volume with the buttonsThe speaker volume can be adjusted when an audio signal is being input.

Notes• Note that a lamp characteristics may rarely cause the brightness to fluctuate slightly.• A lamp is consumable item. If used for extended periods, images will appear dark, and

the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (Thelifetime of the lamp depends on conditions of use.)

• The DMDTM is made using extremely advanced technology, but there may be black spots(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. Pleasenote that these are not malfunctions.

• Although this projector supports a wide range of RGB signals p.56 , any resolutions notsupported by this projector (XGA) will be expanded or shrunk, which will affect imagequality slightly. To view high-quality images, it is recommended that the computer’sexternal output should be set to XGA resolution.

• With some models of computer having LCD displays or the like, displaying imagessimultaneously on the projector and the monitor’s display may prevent the images fromdisplaying properly. If this happens, turn off the computer’s LCD display. For informationon how to turn off the LCD display, see the owner’s manual of your computer.

• If no signal is being input from the connected equipment or signal input is stopped whileprojecting, the “No signal” will appear.

• If a signal not supported by the projector is input, the “Unsupported signal” will appear.• If an unavailable operation button is pressed, the icon will appear.

1

2

1

2

3

1 Turn on the power.Turn on the power by following the instructions in “Turning the power on” p.26 .

2 Select the language and the lamp power (When using thefirst time).When the projector is used for the first time after purchase, the start menu for lan-guage (to display the menus and messages on the screen) and lamp power selectionand configuration is displayed in English. (If the screen is out of focus, adjust itaccording to the step 6 .)

q Use the or button to select thedesired language and press the button.Message for setup confirmation is displayed in aselected language.Then, the menu for lamp power selection andconfiguration is displayed. It is automatically set asStandard. To change the setting, follow the step w.

w Use the or button to select the lamppower and press the button.The lamp power, if selected, will be toggled withoutpressing the button. The display automaticallydisappears in a few seconds.

Notes• When the projector is turned on the next time, the start menu does not appear upon

startup. However, if [Reset all] is executed from the Default setting menu p.44 , thestart menu will be displayed the next time when the power is turned on.

• The language can also be set via the Display setting menu p.41 and Lamp powervia the Default setting menu p.44 .

• This owner’s manual assumes that English has been selected.

3 Activate the connected device.Turn on and start the connected device such as a computer.

4 Press the INPUT button.An image of the connected eqipment is projected.Each time you press the INPUT button, it switches to the input of the connectedequipment that is outputting video signals.

Notes• When [Auto input search] is set to [On] in the Default setting menu p.44 (factory

setting is [On]), the input is switched to the connected equipment that is outputting videosignals each time you press the INPUT button p.45 .

• If no signal is being output from the connected equipment, pressing the INPUT buttondoes not change the input and “There is no other input signal.” will appear.

Basic operations

EnglishFrenchGermanItalianSpanishPortugueseRussianSwedishTurkishPolishJapaneseChinese (simplified)Chinese (traditional)Korean

31

Op

erat

ion

s

30

Adjusting vertical distortion [Auto]2 Press the button.

The keystone distortion is automatically corrected. The icon appears during thiscorrection.When adjustment is finished, the Keystone menu appears again. For fine adjust-ment, select [V-keystone] by the button and adjust image manually by the

buttons.

Adjusting vertical distortion [Manual]1 Press the KEYSTONE button.

2 Select [V-keystone] by the button.

3 Use the buttons for keystone adjustment.

Adjusting horizontal distortion [Manual]1 Press the KEYSTONE button.

2 Select [H-keystone] by the button.

3 Use the buttons for keystoneadjustment.When the adjustment is finished, the menuautomatically disappears. The menu also disap-pears when the KEYSTONE or RETURN button ispressed.

Notes• To adjust both vertical and horizontal keystones, adjust vertical keystone at first.• Depending on the amount of keystone adjustment and the content of images, some

information may be lost, or the picture quality may suffer.

Resizing imageThe projected image can be resized (zoomed in/out).

1 Press the remote control’s RESIZE button.Each time you press the RESIZE button, zoom ratio is up. You can keeppressing.

Before correction After correction

Using auto setting (Only for analog input from computer)This function sets up the projector to the optimum state such assampling phase, frequency, screen position, and clamp for eachtype of the input signal by using simple operations.

Press the remote control’s AUTO SET button.For computer input, the icon will appear during processing.You can set as well by selecting [Auto setting] in the Imageadjustment menu p.39 .

Notes• The image may not be projected or auto adjustment/setting may not be performed

correctly for input signals other than those supported by the projector p.56 , p.57 .• If auto setting fails adjustment, adjust manually with the Image adjustment menu

p.39 .

Correcting the keystone distortionWhen the projector placement angle against thescreen is changed while projecting the image,the picture will undergo keystone (trapezoidal)distortion.This projector is capable of correcting this keystonedistortion.

1 Press the KEYSTONE button.The Keystone menu appears. By default, [Auto V-keystone] is selected.

Item Description

Automatically corrects the vertical distortion.Press .

Screen shrinking at Screen shrinking at bottom top

Screen shrinking on Screen shrinking onthe left the right

Auto V-keystone

V-keystone

H-keystone

Using handy features

Control panelRemoteControl

Before correction After correction

RemoteControl

33

Op

erat

ion

s

32

Changing picture modeThe projected image mode can be selected.

Press the remote control’s PICTURE button.Pressing the button switches Bright/Standard/True color in turn.

Note• [Picture mode] of the Image adjustment menu has the same

function p.39 .

Changing screen sizeThe screen size for the projected image can be changed.

Press the remote control’s SCREEN SIZE button.Pressing the button switches Full/Thru/Wide in turn.

Notes• Thru display is available for computer-input images.• [Screen size] of the Display setting menu has the same function

p.41 .• If you use this function on commercial video software, broadcast

or cable-broadcasting except for the purpose of your privateviewing and listening, it may infringe the copyright protected bythe copyright laws.

Freezing the image (Freeze)The image being projected can be frozen. This function is to be usedto pause a video during a presentation, etc.

Press the remote control’s FREEZE button.The picture pauses. (The Freeze function is released whenpressing the FREEZE button again.)

Notes• The icon will appear while freeze is in effect.• Other operation will also release the freeze.• Even if an image is frozen on the projector, the pictures are

running on the video or other equipment.• If you use this function on commercial video software, broadcast

or cable-broadcasting except for the purpose of your privateviewing and listening, it may infringe the copyright protected bythe copyright laws.

RemoteControl

RemoteControl

RemoteControl

2 To zoom out, press the remote control’s RESIZE button.

Each time you press the RESIZE button, zoom ratio isdown. You can keep pressing.(However, the image cannot be smaller than the originalsize.)

3 To move the area to zoom in, use the buttons.You can keep pressing.

4 To reset the zoom, press the RETURN button.The image is reset to the original size.

Notes• The icon appears while resizing.• Operating a function other than Mute will release resizing.• As zooming is processed digitally, the image quality is degraded in larger zoom

ratio.• During resizing or moving the zooming area, the image may be distorted.

Cutting off the picture and sound temporarily (Mute)When you want to project the images of another projector, overheadprojector, etc. temporarily, this projector’s images and sound can beturned off.

Press the remote control’s MUTE button.The picture and sound are cut off. (The Mute function is releasedwhen pressing the MUTE button again.)

Notes• The icon will appear while mute is in effect.• Operating any other functions will also cancel the muting.

RemoteControl

RemoteControl

Using handy features (Continued)

35

Op

erat

ion

s

34

Displaying two screens (SPLIT function)This function displays two screens at a time.

Press the remote control’s SPLIT button.The projected image moves to the left (mainscreen), and a new image is displayed tothe right (sub screen). To switch the sub andmain screens, press the remote control'sSWAP button.To hide the sub screen, press the SPLITbutton again.

Notes• Sound of the main screen is output.• Size of the screens and input source of the sub screen can be changed in the

SPLIT menu.• Compared with the main screen, the sub screen may suffer some slight image

degradation.• Operating a function other than Mute, Freeze and volume control will release the

SPLIT mode.• If you use this function on commercial video software, broadcast or cable-

broadcasting except for the purpose of your private viewing and listening, it mayinfringe the copyright protected by the copyright laws.

SPLIT function settingPressing the MENU button while two screens are displayed displays the SPLIT menu.This menu sets up both screens.To hide the menu, press the RETURN button.

Sets size of both screens.

Selects the input source for the sub screen.When the main screen is input from computer or Y/PB/PR:Press or , toggle the input with and fix selection with .

Video/S-videoWhen the main screen is input from video or S-video:Press or , toggle the input with and fix selection with .Computer (1) (Digital) / Y/PB/PR (1) (Digital) / Computer (1) (Analog) / Y/PB/PR (1) (Analog) / Computer (2) / Y/PB/PR (2) / Computer (3) / Y/PB/PR (3)

Size

Sub input

Item Description

Note• To enlarge the screen fully, select [Full] for [Size].

RemoteControl

Using handy features (Continued)

Display a sub screen (PIP function)Another image can be added in smaller size(referred as sub screen in this manual) to theprojected image (referred as main screen).

Press the remote control’s PIPbutton.A sub screen is displayed in the currentlyprojected image (main screen).To swap the main and sub screens, pressthe remote control’s SWAP button.To hide the sub screen, press the PIP button again.

Notes• Sound of the main screen is output.• Input select, display position and size of the sub screen can be changed in the PIP

menu.• Operating a function other than Mute, Freeze and volume control will release PIP

mode.• If you use this function on commercial video software, broadcast or cable-

broadcasting except for the purpose of your private viewing and listening, it mayinfringe the copyright protected by the copyright laws.

Sub screen settingPressing the MENU button while the sub screen is displayed displays the PIP menu.This menu sets up the sub screen.To hide the menu, press the RETURN button.

Sets the sub screen size.Large Medium Small

Sets display position of the sub screen.

Selects the input source for the sub screen.When the main screen is input from computer or Y/PB/PR:Press or , toggle the input with and fix selection with .

Video/S-videoWhen the main screen is input from video or S-video:Press or , toggle the input with and fix selection with .Computer (1) (Digital) / Y/PB/PR (1) (Digital) / Computer (1) (Analog) / Y/PB/PR (1) (Analog) / Computer (2) / Y/PB/PR (2) / Computer (3) / Y/PB/PR (3)

PIP size

PIP position

PIP input

Item Description

RemoteControl

37

Op

erat

ion

s

36

How to set password (from [Off] to [On])1 Select [Password] in the Default setting menu and press the or

button.The password setting confirmation screen is displayed. ([OK] or [Cancel])

2 Select [OK] and press the button.The password entry screen is displayed.

3 Enter a four-digit number for the password using numeric keys of theremote control.The input number appears as [****].

4 Re-enter the same password for confirmation.When the password is confirmed, the setting is complete and the passwordbecomes [On].If the password is wrong, repeat the procedure from step 2 .

How to operate when password is [On]1 Turn on the power.

2 The lamp lights and the password entry screen appears.

3 Enter the password using numeric keys of the remote control.If the entered password is correct, the start-up screen appears and the projectorgoes into normal operation. If the password is wrong, a message appears toprompt you to re-enter the password. If you enter a wrong password for more than5 times, the projector will automatically power off and enter standby mode.

How to cancel password (from [On] to [Off])1 Select [Password] in the Default setting menu and press the or

button.The password entry screen is displayed.

2 Enter the password using numeric keys of the remote control.

3 The password cancel confirmation screen is displayed. ([OK] or[Cancel])

4 Select [OK] and press the button.The [Password] is canceled and becomes [Off].

Note• The password entry screen appears when the power is turned back on only after

the main power switch is turned off or the power cord is unplugged.

If you forgot the password, please inquire your dealer.

Screen combination of PIP and SPLIT functions

Computer (1) (Digital) / Y/PB/PR (1) (Digital)

Computer (1) (Analog) / Y/PB/PR (1) (Analog)

Computer (2) / Y/PB/PR (2)

Computer (3) / Y/PB/PR (3)

Video

S-video

A

B

Group Input signal

For PIP functionA: Main screen, B: Sub screenA: Sub screen, B: Main screenYou cannot display two screens of the same group in the PIP mode.

For SPLIT functionA, B or B, A is available.You cannot display two screens of the same group in the SPLIT mode.

Password functionWhen the password function is added and [Password] is set to [On], image projectionrequires an entry of the preset password at power-on.To add the password function, perform the following procedure:(The password function, once added, cannot be deleted. Set [Password] to [Off] if youdo not want to use it after addition.)

1 Set the projector to the operating status or the standby mode.

2 Keep pressing the button for about 10 seconds until a beepsounds.The password function is added when the steps up to here have been completed. Itis also added to the Default setting menu.

Using handy features (Continued)

39

Op

erat

ion

s

38

The image adjustment menuUse this menu to set or adjust image-related items. Items that can be set or adjusted aremarked with “Yes”, and those that cannot are marked with “No”. (When an item is masked,it indicates that you cannot select for the current input.)

Digital (DVI) Analog (D-SUB)(BNC)Item Description

RGB Y/PB/PR RGB Y/PB/PRVideo S-video

Contrast Adjust the image contrast. Yes Yes Yes Yes Yes YesLower Higher

Brightness Adjust the brightness of the image. Yes Yes Yes Yes Yes YesDarker Brighter

Color Adjust the color of the image. No Yes No Yes Yes YesLighter Deeper

Tint *1 Adjust the tint of the image color. No No No No Yes YesReddish Greenish

Sharpness Adjust the sharpness of the image. No Yes No Yes Yes YesSofter Sharper

Noise Set the function to reduce screen noise. No Yes No Yes Yes Yesreduction *2 On (Enable) Off (Disable)

Picture mode Press . Toggle the picture mode with Yes Yes Yes Yes Yes Yes .

Bright/Standard/True color

R-level Adjust red of the image color. Yes Yes Yes Yes Yes YesLess red More red

G-level Adjust green of the image color. Yes Yes Yes Yes Yes YesLess green More green

B-level Adjust blue of the image color. Yes Yes Yes Yes Yes YesLess blue More blue

NTSC mode*3 Set the black level with . No No No No Yes YesUS : NTSC (US) modeJapan : NTSC (JAPAN) mode

Auto setting Automatically adjusts items such as the No No Yes No No Nosampling phase depending on the type ofinput signal.

Phase Adjust with to eliminate flicker. No No Yes No No No

Frequency Adjust with to eliminate periodic No No Yes No No Nopatterns and flickering when many verticallines appear on the screen.

H-position Adjust the horizontal position of the image. No No Yes No No NoMove left Move right

You can call up on-screen menus, and conduct a number of adjustments and settings usingthe operation buttons p.16 on the control panel (main unit side) and remote control.

How to use the menusThe menu shown below is for operation instructions purposes and might differ from theactual display.

Using the menus

Execute

+16

+16

+16

+16

+16

+64

+64

+32

255

255

30

Standard

Brightness +12

Image adjustment

ContrastBrightnessPicture modeR-levelG-levelB-levelAuto settingPhaseFrequencyH-positionV-positionClamp 1Clamp 2

+12+12

Bright+12+12+12

+12+12+12+12+12+12

To image adjustment menu

On

On

On

Language English

Standard

Off

Off

On

Manual

Low

1

Yes

Key lock Off

Toggle items with . Select items with and press . Fix selection with .

Display the Setting display menu.1. Press the MENU button2. Select a Category

3. Adjustments & Settings

Select a category by using .

There are following five categories:

Displays the current adjustments and settings of selected category.Item shown with gray cannot be adjusted with the current input source.

p.39Image adjustment menu

p.41Display setting menu

Default setting menu p.44

Control setting menu p.46

The figure shows displays given for operation instructions purposes. As the display may differ depending on the item, use the following pages as a reference.

ItemAdjustment/Setting Value

These marks signify the items can be adjusted/set by using .

These marks signify the items can be selected from the list by using .After an item is selected, apply it by pressing .

Press or to open the menu.

Status display menu p.48

These marks signify that there are options. Press or to display a list of options.

These marks signify that there are setting screens. Press or to display a list of setting screens.

* When no item is changed, press .

4. Back RETURN button5. End Press the MENU button or RETURN button.

(The menu disappears 30 seconds after the last operation.)

41

Op

erat

ion

s

40

The display setting menuUse this menu to set screen display-related items.(The items in gray color cannot be set with the current input selection.)

(Full): Display with 1024 × 768 dot resolution(Thru): Display with sampling resolution (for computer input only)(Wide): Wide-screen display

Select one of the languages below to use for displaying the menu and messages[ or : Enter setting mode] [ :Selection] [Apply: ]English/Français/Deutsch/Italiano/Español/Português/ /Svenska/Türkçe/Polski/ / / /

Screen to display when there is no input signal[ or : Enter setting mode] [ :Selection] [Apply: ]Logo/Blue/None

Display icons as function guides On Off

Sound a beep when operation is done. On Off

Display start-up screen when power is turned on On Off

Display a logo customized by the user for the start-up screen or when there is no input signal.[ or : Enter setting mode] [ : Selection]

Logo registration Press to display the registration menu.

Display style

Background Black Blue White

Logo confirmation Press .

Reset logo Yes No

DescriptionItem

Screen size

Language

Background

Icon

Beep

Start-up screen

User logo

Detailed description[Screen size]• If “Thru” is selected for [Screen size], portions exceeding the native resolution

(1024 × 768 pixels) will not appear on the screen. Note that for RGB signals withclock frequency 140MHz or lower, all input pixel signals are sampled. However, ifthe clock speed is higher than this, the RGB pixel signal is thinned beforesampling.

• If you use the screen size setting function on commercial video software,broadcast or cable-broadcasting programs to display images with the varyingaspect ratio except for the purpose of your private viewing and listening, it mayinfringe the copyright protected by the copyright laws.

Digital (DVI) Analog (D-SUB)(BNC)Item Description

RGB Y/PB/PR RGB Y/PB/PRVideo S-video

V-position Adjust the vertical position of the image. No No Yes No No NoMove down Move up

Clamp 1 Adjusts the clamp pulse position. No No Yes No No NoLower Higher

Clamp 2 Adjusts the clamp pulse width. No No Yes No No NoNarrower Wider

Equalizer Reduce noise on the screen. Yes Yes No No No NoAdjust with .

*1: [Tint] and [NTSC mode] can be displayed and adjusted only when the video signal is set to[NTSC] and [NTSC4.43].

*2: [Noise reduction] may not work depending on signal type.*3: [NTSC mode] is set to JAPAN when the language is set to Japanese. It is set to US for other

languages.

Using the menus (Continued)

43

Op

erat

ion

s

42

<Background>Sets background color when [Center] is selected for the logo display mode.

<Logo confirmation>You can preview the registered logo.

<Reset logo>You can reset the registered logo, display style and background to the factorysetting. (The logo set for the start-up screen and background is reset.)

[Background]• TOSHIBA is set for [Logo] by factory setting.• If user’s logo has been registered, it is displayed when [Logo] is set for

background.[Start-up screen]If user’s logo has been registered and this setting is [On], the logo is displayed atstart-up.[User logo]Registers a part of the image that is input from computer and displays it as a logoat start-up and when no signal is input.

<Logo registration>

How to register user logo1 Select [User logo] in the Display setting menu, and press the

or button.

2 Select <User logo registration> from the displayed menu listand press the button.

3 The registration area is displayed for confirmation. Select [OK]or [Cancel] and press the button.• If the picture does not fall within the area, operate the computer to scroll

the screen.

4 Press the button to register.

5 Registration starts.• A message is displayed while registration is in process.

Notes• You can register a logo from computer input only.• The area that can be registered is 512 × 384 dots at the center of the screen. To

register a company logo, prepare the image within the limit.• Only one logo can be registered. When a new image is registered, the old one is

erased.• The time needed to register or display the image varies depending on the data size.• If you use this function on commercial video software, broadcast or cable-

broadcasting except for the purpose of your private viewing and listening, it mayinfringe the copyright protected by the copyright laws.

<Display style>Select the size of the registered logo (except during the PIP and SPLIT modes).

: Displays the registered image in original size at center of the screen.: Displays the registered image by enlarging fully in the screen.

(As processed digitally, the image quality is degraded.)

Using the menus (Continued)

45

Op

erat

ion

s

44

[Auto input search][On]: Automatically searches the signals that

can be projected, and switches inputfrom the connected device that outputsthe signals each time the INPUT buttonis pressed. The input from the connecteddevice that outputs no signals is skipped.

[Off]: Displays the Input select menu.

Toggle with buttons and press button. (The input without signals can beselected.)

[Power on]Note that if [Power on] is set to [Auto], then if the main power switch is ON whenpower is restored after a power outage, the projector will come on.

[Lamp power]When [Lamp power] is set to [Low], the screen becomes a little darker, but thecooling fan noise gets quieter.

[Fan mode]Setting [Fan mode] to [High] increases the cooling fan speed. Set this option touse the projector, for example, at high altitude (over 1,500 meters above sea level).

[Remote control]Sets a remote control code from 4 types. You can set each code respectively for upto 4 projectors. The factory setting is [1].To switch codes, set the same code for the projector and the remote control.A remote control code is applied after the setting is done.• You cannot operate the remote control if the codes of the projector and the

remote control do not match.

Remote control code setting for remote controlRemove the battery cover and set the same remote control code switch as theprojector. p.16 (Use a screwdriver with thin tip to set.)

[Key lock]Protect from operating errors by locking on the control panel buttons of theprojector. (The remote control operations are available.)Control panel operations are locked after the setting is done.• To release the key lock, press the control panel’s RETURN button for 10 seconds.

The key lock is released with a beep sound.

Computer (1) (Digital)Y/PB/PR (1) (Digital)Computer (1) (Analog)Y/PB/PR (1) (Analog)Computer (2)Y/PB/PR(2)Computer (3)Y/PB/PR(3)VideoS-video

Input select

/ shows whether signal is input or not.

Input select menu

Using the menus (Continued)

The default setting menuThis menu shows placement status and other settings.

Sets projection mode in accordance with Placement Style.

When projecting on a non-screen surface, select a color in accordance with the projecting surface.Press and switch with and . Off/Green/Black/Brown/Blue/Beige

Set the time to wait for the power to be turned off after the last operation is made with no input signal.Press and switch with and .Off (not turned off)/1 min./5 min./10 min./30 min./60 min.

Set whether the input with signals is only selected or not.

Sets whether to turn on the power when the ON/STANDBY button is pressed (Manual), or when the power cord is plugged in (Auto). Manual Auto

Sets the lamp power.

Sets the cooling fan speed.

When two or more projectors are used and controlled by the remote control respectively, this menu sets the code for the projector and the remote control.[ or : Enter setting mode] [ : Select item] [ : Select from 1, 2, 3, 4] [ :Confirm] [ :Select OK to end] Press [Cancel] to return.

Lock the control panel buttons.[ or : Enter setting mode] [ : Select item] [ : Select On/Off] [ :Confirm] [ :Select OK to end] Press [Cancel] to return.

Press . (The password and user logo are not reset.)Resets all adjustments and settings to their factory settings.

Password functionWhen [Password] is [On], the Password Setting screen is displayed.

DescriptionItem

Projectionmode

Blackboard mode

No signal power off

Auto input search

Power on

Lamp power

Fan mode

Remote control

Key lock

Reset all

Password

(Rear mounted from ceiling)

(Standard) (Rear) (Mounted from ceiling)

On Off

Standard High

Yes No

Off On

Low Standard

p.22

p.36

Detailed description[Blackboard mode]Projects the image in colors more like projecting on a screen.

Precaution• The projected image may differ depending on the type, color, and material of the

blackboard and wall even if the selected color is the same as the projectedscreen.

47

Op

erat

ion

s

46

<Subnet mask>: For dividing the network, the subnet mask determines the rangeof an IP address assigned to a terminal. (Example: 255.255.xxx.xxx)

<Gateway>: Gateway specifies a network device like a router when accessing aserver outside the network. It is identified by an IP address. (Example:111.112.xxx.xxx)

[Email]<Status notification>: Sends alarm information to the specified E-mail addresswhen an error such as lamp blowout occurs.

<SMTP server>: Set an IP address of the SMTP server.

<Port number>: Enter a port number of the SMTP server.

<Destination address>: Enter within 60 characters. (Example: xxx@xxx.xxx)

Character entryEnter characters using numeric keys of the remote control.The character is entered with a beep sound if the beep sound is set to [On].

Character entry mode

Remote control button

Items using characters, numbers, and symbols(e.g., projector name and destination address) Number only

“1” “.” “@” “-” “_”

“2” “A” “B” “C” “a” “b” “c”

“3” “D” “E” “F” “d” “e” “f”

“4” “G” “H” “I” “g” “h” “i”

“5” “J” “K” “L” “j” “k” “l”

“6” “M” “N” “O” “m” “n” “o”

“7” “P” “Q” “R” “S” “p” “q” “r” “s”

“8” “T” “U” “V” “t” “u” “v”

“9” “W” “X” “Y” “Z” “w” “x” “y” “z”

“0” “space!"#$%&'()*+,-./:;<=>?@[＼]^_`｜~”

Deletes one character.

“1”

“2”

“3”

“4”

“5”

“6”

“7”

“8”

“9”

“0”

Deletes one character.

Using the menus (Continued)

The control setting menuThis menu sets items regarding wired LAN.By this setting, you can transmit operation status messages from the projector to thespecified E-mail address.

[ : Wired LAN setting] [ : Select item]

Projector name: Enter a character string (0 to 64 characters) using numeric keys of the remote control.

DHCP: Use Not use

IP address: Enter a character string using numeric keys of the remote control.

Subnet mask: Enter a character string using numeric keys of the remote control.

Gateway: Enter a character string using numeric keys of the remote control.

Confirm: [OK Cancel]

[ : E-mail setting] [ : Select item]

Status notification: On Off

SMTP server: Enter a character string using numeric keys of the remote control.

Port number: Enter a character string using numeric keys of the remote control.

Destination address: Enter a character string using numeric keys of the remote control.

Confirm: [OK Cancel]

DescriptionItem

Wired LAN

Email

Detailed description[Wired LAN]<Projector name>: Setting a projector name helps you identify each of theprojectors that are connected to the network.• You cannot set a projector name starting with ERR.

<DHCP>: When <DHCP> is set to [Use], an IP address is automatically assignedto the projector by a DHCP server. In case of a network that an IP address cannotbe assigned automatically, set <DHCP> to [Not use].When <DHCP> is set to [Not use], ask your network administrator for IP address,subnet mask, and gateway, then set the following items manually:

<IP address>: This is a unique number assigned for a terminal to connect to anetwork. The format is a quartet of 3-digit decimal number. (Example:111.112.xxx.xxx)

48 49

Mai

nte

nan

ce

The product’s light source is a mercury lamp that lights at increased internal pressure. Be sureto fully understand the following characteristics of the lamp and handle it with extreme care.

• The lamp may burst with a loud noise due to impact or deterioration, or fail to light atthe expiration of its life.

• How long it takes before the lamp bursts or the life expires may vary greatly by lamp.Some may burst shortly after first use.

• Burst is likely to happen if the lamp is used after the replacement period has elapsed.• When the lamp bursts, the broken pieces of glass may get inside the product or be

released outside from the openings for ventilation.• When the lamp bursts, a slight amount of mercury gas enclosed in the lamp along with

glass dust may be released from the openings for ventilation.

Immediately replace the lamp when a sign appears on the screen.• When the replacement time approaches, a message will appear on the screen.• The risk of burst will increase if the lamp is continuously used without being replaced.• Frequently check the used hours and prepare spares when the replacement time

approaches. (Refer to “Status display”. p.48 )

When the lamp is broken• If glass components, including a lamp and a lens, should break, handle the broken

pieces with care to avoid injury and contact your dealer for repair service.• In the event of lamp burst, unplug the product from the wall outlet, leave and completely

ventilate the room. Then, thoroughly clean the area around the projector and discardany edible items placed in that area.

• When the lamp bursts, consult a doctor if glass dust or mercury gas gets into your eyesor you breathe it.

Lamp replacementA lamp is consumable supplies. If used for extended periods, images will appear dark, andthe lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The lifetimeof the lamp depends on condition of use.) If this happens, replace it with a new one.

WARNING• If the projector is mounted on the ceiling, it is recommended to use your Toshiba dealer-

ship when the lamp has to be exchanged.Uncovering the lamp while the projector is mounted on a ceiling may lead to a dangerof damage from falling pieces of glass if the lamp is broken. Besides, working at highelevations can also be hazardous. Do not attempt to replace the lamp by yourself.

• When replacing, always use lamp “TLPLW6” (sold separately).

CAUTION• If you have been using the projector, the lamp will be very hot, and may cause burn injuries.

Wait for the lamp to cool (for longer than 1 hour) before replacing it.• If the lamp should break, please handle with care to avoid injury due to broken pieces and

contact your dealer for repair service.

About lampMaintenance

Using the menus (Continued)

Displaying Information (Status display)This displays information about the input signal, lamp use time, LAN connection status,etc.

“Yes”: displayed, “No”: not displayed

Item Description Computer Y/PB/PR Video S-videoProjectorInput Input source name Yes Yes Yes YesMode name RGB input mode [Note 1] Yes No No NoResolution Resolution (in dots) Yes No No NoFrequency Sync frequency Yes No No NoSync Sync signal polarity [Note 2] Yes No No NoSignal format Y/PB/PR signal format No Yes No NoVideo mode Color method of video signal No No Yes YesLamp time Time of lamp use [Note 3] Yes Yes Yes YesLamp reset count The count for lamp replacement Yes Yes Yes YesTotal time The total time that this projector is

used.Yes Yes Yes Yes

Version Firmware version [Note 4] Yes Yes Yes YesWired LANConnection status Displays connection status of LAN. Yes Yes Yes YesIP address Displays the IP address. Yes Yes Yes YesSubnet mask Displays numeric value of subnet

mask.Yes Yes Yes Yes

Gateway Displays numeric value of gateway. Yes Yes Yes YesMAC address Displays MAC address of the

projector. [Note 5] Yes Yes Yes Yes

Notes1: The mode of supported RGB signals p.56 is shown.2: Sync signal polarity shown as P (positive) or N (negative) for [H/V].3: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as

a counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours, consultwith a store about getting a TLPLW6 replacement lamp (sold separately) prepared.

4: [Version] shows the version of the projector’s internal control program. This version is referredto for customer service, etc.

5: In case that “------” appears for MAC address, please contact your dealer.

Note• The displayed information will not be refreshed if the status changes. To refresh the

information, dismiss the display, then display it again. The information regardingwired LAN is refreshed every time it is displayed.

5150

Mai

nte

nan

ce

Lamp replacement (Continued)

1 Unplug power cord.

2 Wait until lamp is sufficiently cooled.Wait for at least 1 hour.

3 Remove the outer lamp cover.Loosen the two screws, raise the outer lampcover with your fingers as shown to remove theouter lamp cover. Use care to avoid anydamage to nails and/or tip of your finger(s). Ifyou have any difficulty in removal, you can usea screwdriver or any other smaller tool for yourconvenience.

4 Remove the inner lamp cover.Loosen the screw to remove the inner lampcover.

5 Pull out the lamp.Loosen the three lamp locking screws, pull up thehandle, and press the tab to remove the lamp.

6 Mount the new lamp.Align the orientation, press down the new lampuntil the bottom is reached, and lock in place usingthe three lamp locking screws.

Outer lamp cover

2

1

1

2

1

2

2

1

3

4

Inner lamp cover

5

6

7 Replace the inner lamp cover.Tighten the screw loosened in step 4 until theinner lamp cover is no longer loose.

8 Replace the outer lamp cover.Align the cover, and press it in, then tighten thescrews loosened in step 3 until the outer lampcover is no longer loose. (Be sure to replace theouter lamp cover.)

9 Reset the lamp timer.See the lamp’s manual for instructions on resettingthe lamp timer.

Notes and Precautions• Press the button twice to display (a rough guide) the time of lamp use, the [Lamp

time] item, in the Status display menu. p.48

• It is recommended that the lamp be replaced after 2,000 hours of use. When [Lamp time]reaches 2,000 hours, the icon and a message will appear with a beep sound. (After2,000 hours, they will appear when the power is on at the first time every 100 hours.) Thisdisplay disappears when you press the button.

• Attach the outer lamp cover correctly so that it is not loose. If it is not attached correctly,the projector may fail to be powered on or the lamp may fail to come on.

• Always replace the lamp with a new one.• The lamp is made out of glass. Do not touch the glass surface with your bare hands,

bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)

Used LampsThis projector’s lamps contain trace amounts of environmentally harmful inorganicmercury. Be careful not to break used lamps, and dispose of them in accordance withlocal regulations.

Tab

5352

Oth

ers

The indicator lights and a beep sound inform you of internal abnormalities.

No power⇒ Problem with projector

• Unplug the power cord, and contact your dealer.

Lamp went out during use, or won’t come on⇒ Lamp temperature is high so that it is difficult to turn on, the lifetime of the

lamp has ended or the projector is malfunctioning.• Unplug the power cord and wait for a short while, then turn the power

back on.• If a lamp burns out, replace it with a new one. After approx. one minute of abnormal display, the projector returns to

the standby state waiting for internal cool down.

Power went out during use⇒ Internal overheating, or the outside temperature is too high.

• Place the projector so that the air intake and exhaust are not blocked.• Unplug the power cord and wait for a short while, then turn the power

back on. The icon will appear before the power goes out. After approx. one minute of abnormal display, the projector returns to

the standby state waiting for internal cool down.

Power went out during use⇒ Problem with internal cooling fan.

• Unplug the power cord, and contact your dealer. The icon will appear before the power goes out. After approx. one minute of abnormal display, the projector returns to

the standby state waiting for internal cool down.

Power went out during use, or power won’t come on⇒ The lamp cover is not properly attached.

• Unplug the power cord, and reattach the lamp cover. p.51 After approx. one minute of abnormal display, the projector returns to

the standby state waiting for internal cool down.

Power went out during use⇒ Problem inside the projector.

• Unplug the power cord and wait for a short while, then turn the powerback on.

• If the above action will not clear the problem, unplug the power cord,and contact your dealer.

The icon will appear before the power goes out. After approx. one minute of abnormal display, the projector returns to

the standby state waiting for internal cool down.

WARNING• Request cleaning and maintenance of a ceiling-mounted unit from your projector dealership.

Attempting to clean/replace the lamp at a high site by yourself may cause you to falldown, thus resulting in injury.

Lens cleaning• Clean the lens with a commercially available blower and/or

lens cleaner.• The lens is easily scratched, so do not rub it with hard objects,

or strike it.

Main unit cleaning• Clean the main unit after unplugging the power cord.• Wipe dirt off the main unit gently with a soft cloth.• Do not wipe the main unit with a damp cloth. Doing

so may allow water to get inside, resulting in anelectric shock or failure.

• Do not use benzene, thinner and the like as they maydeform or discolor the unit or damage the paintsurface.

• When using a chemically treated cloth, follow theprecautions included with the cloth.

Lens and main unit cleaning

(Off)

Or (Orange lit)

Or (Orange litor flashing)(Red lit)

Trouble indications

(Red lit)

(Green lit)

(Red lit or flashing)

(Red lit)

(Red lit)

(Red lit)

(Red lit)

(Greenflashing)

(Orangeflashing)

(Red lit)

5554

Oth

ers

If you think something is wrong, check the followings before contacting customer service.Please see “Trouble indications” p.53 as well.

If This Happens Check

No power

Power goes outduring use

No picture

No audio

Picture notdisplayedcorrectly

Picture blurredPart of pictureout of focus

Image is dark

Colors too lightBad shading

Control panelkey doesn’t work

Remote controldoesn’t work

Before calling service personnel

• Is the power cord plugged in? Is it connected to the projector?• Is the main power switch turned on? p.26

• Is the outer lamp cover attached properly? p.50

• Is the ambient temperature high? p.53

• Is the air intake or air exhaust blocked? p.53

• Is the projector turned on? (When [Auto input search] is [Off]) p.45

• Is the mute function on? p.32

• Is the brightness setting minimized? p.39

• Are the connections set up correctly? p.24

• Are all the connected devices functioning properly?

• Is the mute function on? p.32

• Is the volume setting minimized? p.29

• Are the connections set up correctly? p.24

• Are all the connected devices functioning properly?

• Is the input signal supported by the projector? p.56 , p.57

• Is there something generating an abnormal video signal, forinstance the video tape?

• Is the lens dirty? p.52

• Is the lens focus adjusted optimally? p.29

• Is the projection distance within the projector’s supported range? p.23

• Is the projector’s screen placement angle tilted too far? p.23

• Are the sharpness or sampling phase adjustments off? p.39

• Are the brightness or contrast adjustments off? p.39

• Is the lamp nearing the end of its service life? p.48

• Are the color, tint, R-level, G-level, or B-level adjustments off? p.39

• Is the screen dirty?• Is the blackboard mode set properly? p.44

• Is the lamp nearing the end of its service life? p.48

• Is the key lock function on? p.44

• Is the remote control ON/OFF switch set off? p.20

• Is the remote control code identical with the projector's code? p.45

• Are the remote control’s batteries drained?• Are the batteries inserted into the remote control correctly? p.20

• Is the remote control being used within the effective range? p.20

• Are there any obstructions between the remote control and projector?• Are there any fluorescent or other bright lights shining at the

projector’s infrared remote sensor?

Specifications List of general specifications

Item SpecificationConsumption Power 390 WWeight 4.9 kgExternal Dimensions

340 × 115 × 314 mm (W × H × D)(including protruding parts)Cabinet material PC+ABS resin and ABS resinConditions for usage environment Temp: 5°C to 35°C; relative humidity: 30% to 70%Display pixels 1 chip DMD™Picture elements 786,432 pixels (1024H × 768V)Lens Zoom lens F=2.4-2.6 f=23-27.6 mmLamp High-pressure mercury lamp (300 W)Projection screen size 33-300 inchesProjection distance 1.29-12.10mSpeaker 4 W + 4 W (stereo)

CONTROL terminal LAN: 10BASE-T/100BASE-TXRS-232C: Mini DIN 8 pin

COMPUTER(Y/PB/PR) 1 DVI-I: Analog RGB / Digital RGB / Y/PB/PR (dual use)IN terminal AUDIO: 3.5mm dia. stereo mini-jack, 1.5 V (rms)COMPUTER(Y/PB/PR) 2 Mini D sub 15 pin Analog RGB / Y/PB/PR (dual use)IN terminal AUDIO: 3.5mm dia. stereo mini-jack, 1.5 V (rms), 22 kΩ or moreCOMPUTER(Y/PB/PR) 3 G/Y: BNC Jack G: 0.7 V (p-p), 75Ω, Y: 1 V (p-p), 75ΩIN terminal B/PB: BNC Jack 0.7 V (p-p), 75Ω

R/PR: BNC Jack 0.7 V (p-p), 75ΩHD (Horizontal sync signal): BNC Jack TTL level (Pos/neg polarity)VD (Vertical sync signal): BNC Jack TTL level (Pos/neg polarity)AUDIO: 3.5mm dia. stereo mini-jack, 1.5 V (rms), 22 kΩ or more

VIDEO IN terminal S-VIDEO: Mini DIN 4 pinAUDIO (L/R): RCA Pin Jack × 2, 1.5 V (rms), 22 kΩ or moreVIDEO: RCA Pin Jack, 1 V (p-p), 75ΩAUDIO (L/R): RCA Pin Jack × 2, 1.5 V (rms), 22 kΩ or more

MONITOR OUT terminal Mini D sub 15 pin RGB / Y/PB/PR (dual use)AUDIO OUT terminal 3.5mm dia. stereo mini-jack, 1.5 V (rms), 22 kΩ or more

Notes• This model complies with the above specifications.• Designs and specifications are subject to change without notice.• This model may not be compatible with features and/or specifications that may be added

in the future.

Separately sold productReplacement Lamp Model TLPLW6

Con

nect

ion

term

inal

5756

Oth

ers

List of supported signals (RGB signals)This projector supports the following RGB signals. Note, however, that depending on thecomputer model, the screen may show flicker or streaking. Please adjust the projector ifthis happens.

Resolution

720 x 400640 x 480

800 x 600

832 x 6241024 x 768

1152 x 8641280 x 960

1280 x 1024

1400 x 10501600 x 1200

Mode

720x400_85VGA_60VGA_72VGA_75VGA_85

SVGA_56SVGA_60SVGA_72SVGA_75SVGA_85MAC16"XGA_60XGA_70XGA_75XGA_85MAC19"

SXGA1_75QuadVGA_60QuadVGA_85

SXGA3_60SXGA3_75SXGA3_85

SXGA+UXGA_60UXGA_65UXGA_70UXGA_75UXGA_85

Refresh rate(Hz)

85.03959.94072.80975.00085.00856.25060.31772.18875.00085.06174.55060.00470.06975.02984.99774.70075.00060.00085.00260.02075.02585.02459.97860.00065.00070.00075.00085.000

H-frequency(kHz)

37.92731.46937.86137.50043.26935.15637.87948.07746.87553.67449.72548.36356.47660.02368.66760.13467.50060.00085.93863.98179.97691.14665.31775.00081.25087.50093.750106.250

Clock(MHz)35.50025.17531.50031.50036.00036.00040.00050.00049.50056.25057.28365.00075.00078.75094.50079.857108.000108.000148.500108.000135.000157.500121.750162.000175.500189.000202.500229.500

**

* Depending on the model of computer, the image may not be displayed properly with theDVI input.

Note• Signals which resolution exceeds the native resolution (1024 × 768 pixels) will be

compressed. For this reason, some information may be lost, or image quality may beaffected.

Specifications (Continued)

List of supported signals (Y/PB/PR signals)

Signal format fh(kHz) fv(Hz)

480i(525i)@60Hz 15.73 59.94

480p(525p)@60Hz 31.47 59.94

576i(625i)@50Hz 15.63 50.00

576p(625p)@50Hz 31.25 50.00

720p(750p)@60Hz 45.00 60.00

720p(750p)@50Hz 37.50 50.00

1080i(1125i)@60Hz 33.75 60.00

1080i(1125i)@50Hz 28.13 50.00

*

*

* DVI digital input is not supported.

List of supported signals (Video, S-Video signals)Video mode fh(kHz) fv(Hz) fsc(MHz)

NTSC 15.73 60 3.58

PAL 15.63 50 4.43

SECAM 15.63 50 4.25 or 4.41

PAL-M 15.73 60 3.58

PAL-N 15.63 50 3.58

PAL-60 15.73 60 4.43

NTSC4.43 15.73 60 4.43

Pin assignment of COMPUTER-2 & MONITOR terminals

1115

6

15

10

Input Signal• RGB input

RGB signals: 0.7V (p-p) 75 ΩHorizontal sync signal: TTL level (Pos/neg polarity)Vertical sync signal: TTL level (Pos/neg polarity)

• Y/PB/PR inputY signal: 1.0V (p-p) 75 ΩPB/PR signals: 0.7V (p-p) 75 Ω

Mini D sub 15 Pin connector

Pin Pin description

No. During RGB input During Y/PB/PR input

1 Video signal (R) Color difference signal (PR)

2 Video signal (G) Luminance signal (Y)

3 Video signal (B) Color difference signal (PB)

4 GND ∗5 GND ∗6 GND (R) GND (PR)

7 GND (G) GND (Y)

8 GND (B) GND (PB)

9 N.C ∗10 GND ∗11 GND ∗12 N.C ∗13 Horizontal sync signal ∗14 Vertical sync signal ∗15 N.C ∗

∗ Do not connect anything.

5958

Oth

ers

Pin assignment of DVI-I terminal

Specifications (Continued)

Pin No.123456789101112131415

Pin descriptionT.M.D.S. data 2 –T.M.D.S. data 2 +T.M.D.S. data 2/4 shieldedT.M.D.S. data 4 – (N.C)T.M.D.S. data 4 + (N.C)DDC clockDDC dataAnalog vertical sync signalT.M.D.S. data 1 –T.M.D.S. data 1 +T.M.D.S. data 1/3 shieldedT.M.D.S. data 3 – (N.C)T.M.D.S. data 3 + (N.C)+5V power sourceGND(+5V, H Sync & V Sync)

Pin descriptionHot plug detectionT.M.D.S. data 0 –T.M.D.S. data 0 +T.M.D.S. data 0/5 shieldedT.M.D.S. data 5 – (N.C)T.M.D.S. data 5 + (N.C)T.M.D.S. clock shieldedT.M.D.S. clock +T.M.D.S. clock –Analog video signal (R / PR) Analog video signal (G / Y) Analog video signal (B / PB) Analog horizontal sync signal Analog GND(R/PR,G/Y,B/PB)

Pin No.161718192021222324C1C2C3C4C5

COMPUTER IN 1C5

C3 24C4

C1C2 8 1

1617 9

Analog input signal• Analog RGB input

RGB signals: 0.7V (p-p) 75 ΩHorizontal sync signal: TTL level (Pos/neg polarity)Vertical sync signal: TTL level (Pos/neg polarity)

• Y/PB/PR inputY signal: 1.0V (p-p) 75 ΩPB/PR signals: 0.7V (p-p) 75 Ω

DVI digital & analog connector

CONTROL terminal Pin assignment

768

5

4

3

2 1

Signal NameRXDCTSDSRGNDRTSN.CTXDGND

Pin No.12345678

DescriptionReceiving dataConsent to sendData set readySignal groundRequest to sendNo connectionSending dataSignal ground

Mini DIN 8 pin connector

Interface format1 Communication method RS-232C, 9600bps, No Parity, Data Length: 8 bits;

Stop Bit Length: 1 bit2 Communication format STX (02h) Command (3Byte) ETX (03h)

Only 1 command valid per communication.3 Data format For input commands, only ASCII-compliant all-uppercase

alphanumeric characters supported.

4 Replies Acknowledge ACK (06h) CR (0Dh) Data ... Normally ended

ACK (06h) ESC (1Bh) ... Aborted

No acknowledge NAK (15h)

If commands are to be sent consecutively, wait for the response from the projectorbefore sending the next command.

Main CommandsItem Command

Power on PONPower off POFIcon display on MO0Icon display off MO1Auto setting (RGB input) PATStatus display on DONStatus display off DOF

Note• Contact your dealer for control cable and other commands.