tec lars er y s y stem s c h a nd rec ov l au n · certification dnv 2.22 rules for lifting...
TRANSCRIPT
4__Ulmatec Moon Pool LARS™ 6__Ulmatec U-Frame LARS™ 8_Ulmatec Overhead LARS 4.5™
10__Cetix - high performance electrical winches 9__Ulmatec Heavy-Duty LARS 6.0™
Ulmatec has delivered two Moon
Pool LARS™ (pictured), a hydraulic
hatch system for the main moon pool
and skid systems for the work deck on
Island Enforcer, an advanced subsea
construction vessel.
04
ULMATEC MOON POOL LARS™
The Ulmatec Moon Pool LARS™ for safe handling, storing,
launching and recovery through the moon pool. This vertically
guided system is fitted to the moon pool wall. With its
operational area placed inside the vessel and screened from
wind and weather, it is designed to provide a safe platform for
both operators and ROV equipment.
05
2600
CURSOR SYSTEM FOR CONTROLLED RELEASE AND SOFT LANDING
When the ROV/TMS is to be retrieved to the vessel,
it is first raised with the umbilical winch to about 50
metres beneath the keel. The umbilical winch will then
cease lifting and the lower cursor will be lowered to
about 30 metres beneath the keel.
In recovery mode, the umbilical winch will lift
about 20 per cent faster than the cursor winch. This
reduces the jolt when the lower cursor engages with
the ROV/TMS.
When the lower cursor and the ROV/TMS have
latched together, the signal will be given for the
umbilical to change to constant tension (CT) mode,
and cursor winches will guide the lower cursor and
the ROV/TMS into the upper cursor, up into the moon
pool and over the hatches to the deck.
A cursor guides the ROV and its tether management
system (TMS) through the moon pool.
When the ROV/TMS reach the bottom of the moon
pool, the main (upper) cursor halts and the ROV/TMS
is lowered to the desired depth.
The lower cursor is conically shaped in order to
guide the umbilical during the operation.
Controlled release
Soft landing
ULMATEC MOON POOL LARS™
Enlarges the weather window, and thereby
increases the number of operating days
Reduces the danger of damage to the
equipment
LOWER CURSOR
ROV/TMS
80% SPEED
100% SPEED
06
ULMATEC U-FRAME LARS™
The Ulmatec U-Frame LARS™
is a deck-mounted system for safe
handling, storing, launching and
recovery over the side. With its long
reach of 4.5 metres from the vessel side
and 3.5 metres below deck level, it can
be installed on a mezzanine deck, for
instance.
07
ROVVOR
A FLEXIBLE SOLUTION WITH A LONG REACH AND HIGH CAPACITY
The Ulmatec U-Frame LARS™ is a mobile system
which ensures rapid and simple mobilisation and
demobilisation.
As a deck-mounted system, it can easily be adapted
to existing vessels.
Safe working load 15 000kg
The Ulmatec U-Frame LARS™ has properties which
minimise the risk of damaging equipment during
launch and recovery.
In working position, the distance from the ship side
to the umbilical cable is about 4.5 metres.
In addition, the frame extends no less than 3.5
metres down towards the splash zone from the deck
where it has been installed.
Its extended dip features mean that the system
provides flexible positioning. It can be located on a
mezzanine deck, for instance.
Extended dip features
Mobile system
ULMATEC U-FRAME LARS™
Rapid mobilisation – more days in operation.
Flexible choice of vessel.
Can be installed higher than standard
A-frames while reducing the distance to the
splash zone.
3.5m 4.5m
08
ULMATEC OVERHEAD LARS 4.5™
ROVVOR
The Ulmatec LARS 4.5™ is designed to operate at
about 5 metres from the vessel side to the centre of
the umbilical at deck level when in launch and recovery
position. That provides greater distance from the ship
than a standard A-frame, and a considerably lower gap
between the launch/recovery position and the splash
zone. This permits soft handling in rough weather as
well as optimised ROV lowering and raising.
When deploying the ROV, the vertical crib can be
hoisted above the lower part of the hangar side hatch
for more secure operation in heavy seas.
A solid weather-tight hatch measuring three metres
from deck and into the hangar opening can be supplied.
This protects crew and equipment in the hangar
from waves and weather along the vessel side during
operation.
The ROV operators have optimum working
conditions, with a clean ROV deck providing easy access
during service and maintenance.
The system is equipped with a trolley for parking
and separating the ROV and TMS, which simplifies
service and maintenance.
Safe working load 12 000kg
SAFE LAUNCH AND RECOVERY OPERATIONS
5m
09
ROVVOR
ROVVOR
ULMATEC HEAVY-DUTY LARS 6.0™
A guidance system which follows the ROV down
the vessel side is important during launch and recovery
operations on ships where the ROV hangar is a long
distance from the splash zone.
The guidance system eliminates swinging of the
ROV, even with large vessel motion. This eliminates the
danger of the ROV coming into contact with the vessel
side on its way up or down.
The Ulmatec LARS 6.0™ comprises two trolleys –
one horizontal, running on horizontal guide beams
fitted to the hangar ceiling, and the other vertical,
running on vertical guide beams fitted to the horizontal
trolley and the ship’s side.
The system can also be delivered with a guidance
system beneath the sea surface. The vertical guide
beams on the vessel’s side will then end at the bilge
radius below the waterline.
Safe working load 18 000kg
FULL HORIZONTAL AND VERTICAL CONTROL
10
CETIX - HIGH PERFORMANCE ELECTRICAL WINCHES
CETIX WAVERUNNER™ 5R
CETIX WAVERUNNER™ 10R
Umbilical capacity 2 000m of 25.4mm-diameter umbilicalUmbilical speed 0-115 m/minSafe working load 5 000 kgCertification DNV 2.22 rules for lifting applianceses
Umbilical capacity 2 200m of 40mm-diameter umbilicalUmbilical speed 0-115 m/minSafe working load 14 000 kgCertification DNV 2.22 rules for lifting appliances
11
CETIX WAVERUNNER™ 13R
CETIX WAVERUNNER™ 19R
CETIX OCEANRUNNER
Umbilical capacity 2 000m of 25.4mm-diameter umbilicalUmbilical speed 0-115 m/minSafe working load 5 000 kgCertification DNV 2.22 rules for lifting applianceses
Umbilical capacity 2 200m of 40mm-diameter umbilicalUmbilical speed 0-115 m/minSafe working load 14 000 kgCertification DNV 2.22 rules for lifting appliances
Umbilical capacity 3 500m of 40mm-diameter umbilicalUmbilical speed 0-115 m/minSafe working load 19 500 kgCertification DNV 2.22 rules for lifting appliances
Umbilical capacity 4 500m of 39.5mm-diameter umbilicalUmbilical speed 0-115 m/minSafe working load 25 000 kgCertification DNV 2.22 rules for lifting appliances
Umbilical capacity 2 000m of 32.6mm-diameter umbilicalUmbilical speed 0-90 m/minSafe working load 13 000 kgCertification DNV 2.22 rules for lifting appliances
ULMATEC STROMEK ASStrandgata 25 NO-6060 Hareid Norway
Phone: +47 70 01 24 70 Fax: +47 70 01 24 71 E-mail: [email protected] Web: www.ulmatec.no
ULMATEC
Des
ign
: ww
w.o
sber
get
.no