technical data sheet and planning guide - diamantlift.com · technical data sheet and planning...

arnotec GmbH Grünhutstraße 7 D-76187 Karlsruhe Phone +49 721 605 710 70 Fax +49 721 605 710 19 www.diamantlift.com

Technical Data Sheet

and Planning Guide

Model // mikro //


This data sheet is a help in order to check if the

bath lift is suitable for your bath. The following

drawings shall help you to determine the requi-

red space of the lift in your bath.

Tip: Choose the position of the lift about

5 cm above the bathtub rim.

Our model mikro is the smallest lift in our assortment.

This device fits in almost every bathroom and is

extremely stylish. This lift will be the envy of everyo-

ne.

Model mikro

Engineering drawingFront view of the device with dimensions

Device view model // mikro //

41,7 cm

47,0 cm

28,0 cm

18

,0 c

m

14

,8 c

m


Engineering drawingDevice view from the right / left

Rear view of the device plate

Connector for charger

on the left

sturdy handle

made from

stainless steel

12

,0 c

m

7,2 cm

12,0 cm


The dimensions are only for your information.

With each bathlift, we deliver a precise paper

drilling template, which ist simply attached to

the place of installation with adhesive tape.

This facilitates the exact positioning of the drill

holes.

Important: Four tight screws are sufficient for

the fixing. You do not have to fix all holes with

screws on the wall.

The delivery includes:

Drilling template, 4x dowels and 4x screws

For the installation you need:

Hex key, screwdriver cross-recess, ratchet

Engineering drawing

Dimension drawing back

41,0 cm

38,5 cm

3,5

cm

3,5

cm

2,3

cm


1. Determine an appropriate position for the

installation of your bathlift above the tub. The lift

should be installed in a way that a comfortable

position is granted while lowering and rising. As a

rule, we recommend to install it at 1/3 of the

length of the bathtub.

Make sure that the entering and the sitting

position in the tub meet your demands.

2. Make sure that the wall tolerates the load of

the lift. We recommend the installation on a brick

wall (stone, concrete, masonry...).

For stud walls, secure attachment is not always

possible.

3. The belt must be straightly fed out from the

device and mounted on the floor fixing.

Tip: We recommend to install the lift about 5,0 cm

above the bathtub rim!

Planning Guide

1/3 2/3

5,0 cm

Fixation on the floor

Belt is mounted on the fixation on the

floor

Fixation on the side of the bathtub

Belt is mounted on the upper side of the

bathtub rim

5,0 cm

Belt holder Type A

Belt holder Type CBelt holder Type B

5,0 cm

Fixation on the floor

Belt is mounted on the upper side of the

bathtub rim


The right choice?

Take your measurements: take a ruler and mea-

sure the height of the bathtub. Substract at least

5 cm from the measured value and choose the

standard height that is closest to the calculated

value. (51 cm, 46 cm or 41cm)

Example: Your bathtub has a height of 54 cm.

After the deduction you have a value of 49 cm.

The closest standard height would be 46 cm.

Type A

Available heights are 51cm, 46 cm and

41cm. Is fixed to the floor.

Type B

Is fixed to the floor.

Type C

Is fixed to the side of the bathtub.

Belt holder Type A

Belt holder rangeThree different belt holders are available

16,8 cm

42,5 cm

16,8 cm4,5 cm

2,0

cm 4,2

cm

4,2 cm

51

,0 c

m /

46

,0 c

m /

41

,0 c

m

Illustration shows a type A beltholder of 46 cm fixed to the floor.

A B C


Belt holder Type B

Belt holder Type C

The belt holder type B can be directly fixed to the

floor (see image on the left).

This belt holder hardly visible. When the belt holder is

sealed with silicone, wiping up the floor with water is

possible just as before.

Please note:

Type A and B are not suitable for underfloor hea-

tings!

The belt holder type C is suitable for bathtubs that

are walled in. This belt holder can be easily fixed with

five screws on the side of the bathtub.

Please note:

This kind of fixation ist not possible on polystyrene tub

supports.

Belt holder range

4,0 cm

12,5 cm21,0 cm

29,5 cm38,0 cm

21,0 cm

15,3 cm

42,5 cm

15,3 cm4,0 cm

5,0

cm

6,0 cm

2,0

cm 4,0

cm

Illustration shows a type B beltholder fixed on the floor.

Illustration shows a type C belt holder fixed on the side of the bathtub.


Product type

Application field

Support system

Seating belt

Lifting system

Electrical data

Operating devices

Supporting structure

Transport und

Packing dimensions

Belt bath lift / Band bath lift

Plastic skin

Stainless steel mechanics

with disconnectable fastening

Bathing in sitting or reclining position

Operation by the user

Lowering and rising within the bathtub

Width seating belt ca. 28,0 (cm)

Length seating belt ca. 2,55 (m)

Heat resistant up to 60°C

Electrically adjustable with the buttons ( ) or ( )

Max. lifting capacity 120 (kg)

Adjustment range 80/100/120 (kg)

Motor DC 24V/0,7A (max. 4A)

Number of liftings ca. 10 / depending of lifting height and weight of the person

Battery 2 x 12V/1.2 Ah lead battery, gas-tight

Connector power supply +15 bis 18V DC

Power consumption standby ca. 0,01 mA / 0,1 mW

Loading time ca. 24 hrs. for an empty batter

Plug for charger bottom righty

Depending on the version, contact switch on the device or the remote control

Acoustic charging indicator via beeper, LED on the remote control

Clamping assembly on the side of the bathtub / floor fixation

Width ca. 42,0 (cm)

Height 15,0 (cm)

Depth 7,5 (cm) without handle, 11,0 (cm) with handle

Device weight 8,2 (kg)

Tub depth max. 100 (cm)

Length 67,0 (cm)

Width 50,0 (cm)

Height 15,0 (cm)

Weight 11,7 (kg)

Technical specifications

As

of

24

.9.2

01

9

Ve

rsio

n P

-1V

-3

Te

ch

nic

al m

od

ific

atio

ns

an

d e

rro

rs a

re e

xce

pte

d!


Don‘t hesitate to contact us.

We will also be pleased to meet your special

requests.

Phone + 49 721 605 710 70

E-Mail [email protected]

Please visit us on our website www.diamantlift.com

There you can conveniently choose and order your

lift from home.

Should you need any help, we are at your service

by phone.

Any questions?

Convince yourself of the outstanding quality of

our lifts. You can test our bathlifts at our head-

quarters in Karlsruhe (Germany).

technical data sheet and planning guide - diamantlift.com · technical data sheet and planning...

Documents