technical specification manual
TRANSCRIPT
SECURE AND TESTED
WALKWAY, LADDER, PLATFORMAND HANDRAIL SYSTEMS FOR
SAFE BUILDING ACCESS
TECHNICALSPECIFICATIONMANUAL
Technical specificaTion manual
conTenTs
HANDRAILS041 Free standing handrail042 Fixed handrail
LADDERS051 Fixed access ladders – safety cage052 Fixed access ladders – safety line
STAIRS061 Step overs062 Companion way ladders063 Raised walkway
WALKWAY071 GRP walkway072 Galvanised walkway073 Aluminium walkway
WARRANTY DOCUMENT
COPYRIGHT STATEMENTAll rights reserved. Unless otherwise stated the material published within this document is copyright to Sayfa Systems UK Limited. No part may be reproduced, in whole or in part, stored in a retrieval system or transmitted in any form, by any means, electronic, mechanical, photo-copying or otherwise without the specific written permission of Sayfa Systems UK Limited.
REV: 12/09/17PRODUCT DATA SHEET REPORT NO: 041 - A
PRODUCT CODE: SRH5000
SENTRYRAIL FREE STANDING HANDRAIL
041 - A
PRODUCT DESCRIPTION:The SentryRail handrail system is a free standing aluminium handrail system. It is designed to be installed as permanent edge protection on flat roofs and surfaces which have a pitch of less than 10 degrees. The aluminium upright posts are stylish with a raking profile. The aluminium extrusion is rounded with no sharp edges. The SentryRail has a unique patented profile to facilitate ease of installation by incorporating an unlimited extruded U thread. When used with U thread bolts, it allows for an infinitely adjustable connection point on the upright and horizontal handrail tubes. Extra intermediate rails, infill panels and toe-boards can easily be added during or after installation of handrail.
Stability is provided by a cantilever concrete counter balance weight. The weights are approximately 25kg each and can be spaced up to 2.5m centres. It is normal for the weights to be positioned on each upright leg. Double weights can easily be added on any of the upright legs again using the patented profile and U thread bolts. It may be necessary to fit double weights on the end of a handrail run or on very short handrail sections.
Concrete blocks can be colour-coded if required to match the roof finish. The concrete blocks are stylish and low profile. The underside of the weight is smooth to prevent damage to roof covering materials and is installed directly onto the finished roof. A rubber protective matting can be installed under the weight and front foot, but compatibility with the roof covering must be checked prior to installation.
22Kg 44Kg
2.5m 1.25m
EN 13374:2013 BS 6180:2011
Up to a 10 degree pitch
10o
PAYLOAD SENTRYRAIL FREE STANDING HANDRAIL
041
For any technical queries please call our adviceline on 0845 241 9102
To fully comply with standards, it is necessary to have an up-stand on the edge of a roof of at least 150mm to prevent tools and equipment falling over the edge. If no roof up-stand is present the handrail must be fitted with toe-boards to provide this protection. The handrail will be a minimum 1100mm high and the handrail centres will not exceed 450mm.
Involving our design team early in the construction phase will ensure that the most cost effective and safe system is installed. Our designers will consider the safety of both installers during the construction phase and future maintenance personnel.
1100mm
450mmgap
150mmToeboard optional
PAYLOAD SENTRYRAIL FREE STANDING HANDRAIL
SentryRail has purpose made corners and D Ends. These parts have been engineered to a high degree of accuracy and are protected with a colour coded weathrproof gaiter and provide a smooth change in direction on corners and at an end of a run.
Self-closing swing gates are available as standard with a spring return latch and provision to be able to secure with a padlock to prevent unauthorized access to certain areas.
D Ends Swing gateCorners
041
The SentryRail handrail is lightweight yet extremely strong. The aluminium handrail sections are normally supplied to site in 5.0m or 3.0m lengths. A 5.0m section weighs less than 1kg per metre. The benefits during installation are reduced manual handling issues and reduced installation time.
SentryRail can be supplied and installed as a basic handrail edge protection compliant with current legislation or can be provided with optional extras to enhance the system to suit a budget. Handrail can be Polyester powder Coated to match most RAL colour requirements. Colour coding is not recommended in areas of high usage or in harsh environments.
A complete installed SentryRail system can weigh as little as 19kg per linear metre, with a point load of 24Kg. The system therefore has a very impressive safety to weight ratio, which is particularly important on modular or lightweight roof systems where reduced loading applies.
19Kg/m2 47Kg/m2
EN 13374:2013 BS 6180:2011
Point load 24Kg Point load 48Kg
PAYLOAD SENTRYRAIL FREE STANDING HANDRAIL
041
For any technical queries please call our adviceline on 0845 241 9102
ST/ST FixingsConcrete weight
Natural rubber (optional)
Aluminium extrusion
Aluminium extrusion
Nylon end caps, corners and D end connectors Natural rubber base CIS14 Polyisoprene - Optional
1.148,700-13,000 50 - 200 265-4080170resistantresistantresistantresistant
Specific gravity Tensile strength P.S.I. Elongation % Melting Point ºC Minimum ºC Max. - Continuous ºC Max. - intermittent ºC Effect of weak acids Effect of weak Alkalis Effect of Organic solvents Effect of Oils & greases Effect of Sunlight
discolours slightly
30-900.92 3500(24.1)-58/-70
Durometer (Shore A) Specific Gravity (Polymer) Tensile Strength Max-psi (Mpa) Low Temperature Brittle Point (C/F) Tear Strength Flame Retardent Properties Sealing Characteristics
EPP
PAYLOAD SENTRYRAIL FREE STANDING HANDRAIL
MATERIAL SPECIFICATION:
Fixing screws - U thread boltsStainless Steel - Grade 304 (UNS S30400)Fe, <0.08% C, 17.5-20% Cr, 8-11% Ni, <2% Mn, <1% Si, <0.045% P, <0.03% Stainless Steel Surface elctropolished typically 20-40 micron case removal of stainless steel.
Profiled extrusion - Includes handrail tube, front foot and bracketsAluminium extrusion 0.50 - 0.75 Si, Max 0.35, Fe 0.40 - 0.70 MgTensile strength PSI 23,000 Yield strength PSI 15,000
041
OPERATING AND DESIGN STANDARDS:Eurocodes are designated by EN British standards are designated by BS
Note: For guidelines only to be checked by Chief Engineer.
✔
BS ENISO
Standards
• BS EN 13374:2013 (2.5m leg centres and22Kg weights)• BS 6180:2011 (1.5m leg centres and 44Kgweights)• BS EN 12020-1 and 2 :2008 Aluminium andAluminium alloy extrusions• BS EN 755:2008 series Extruded profiles• BS EN 754: 2008 series Tolerances ondimensions extruded profiles• BS 1154:2003- Physical and compositionalproperties for natural black rubber• ISO 9001:2008• ISO 14001:2004• BS OHSAS 18001:2007• Work at height regulations 2005 (Ref.7)
Ultimate serviceability loads BS EN
13374:2013
PAYLOAD SENTRYRAIL FREE STANDING HANDRAIL
Static load
Deflection(Non-permanent)
Overturning
Occasional maintenance usage
300N0.9kN/m
300N
200N
55mm
• Work at height (amendment) Regulations2007 (Ref.8) WAHR
• Provision and use of work equipmentregulations 1998 PUWER 98 (Ref. 5)
• Management of health and safety at workregulations 1999 MHSWR (Ref.2)
• The Building Regulations 2010 part K.
041
For any technical queries please call our adviceline on 0845 241 9102
The company operates to the following standards
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD SENTRYRAIL FREE STANDING HANDRAIL
Ultimate serviceability loads BS 6180:2011
These loads are achievable with profiled uprights spaced at no more than 1.25m and double concrete weights are used on each profiled upright.
Static load
Deflection(Non-permanent)
Overturning
Regular maintenance usage
0.36kN 3.7kN/m
0.36kN
0.5kN
25mm
041
PAYLOAD SENTRYRAIL FREE STANDING HANDRAIL
Maintenance to be in accordance with SIMS standards. (details available on request)
Maintenance to be carried out at time of yearly inspection.
Contact Sayfa Systems to arrange system maintenance.
TRAINING REQUIREMENTS: All personnel who use the Aviator system should have attended a NASLOT (National Access and Safety Line Operator Training) course. Courses are available from Sayfa Systems UK Ltd.
INSPECTION/MAINTENANCE/TRAINING
INSPECTION ROUTINE: All systems to be inspected at least every 12 months from date of installation.
In harsh environments all systems to be inspected at least every 3 months.
Inspections must be carried out by approved Payload engineers.
Inspections must be approved to SIMS (Safety Inspection and Maintenance Service) standards.
Contact Sayfa Systems to arrange inspections.
MAINTENANCE SCHEDULE:All maintenance to be carried out by approved Payload engineers.Maintenance to be in accordance with Sayfa Systems UK (manufacturer) guidelines and recommendations.
In harsh environments all systems to be inspected at least every 3 months.
12 Months
From date of installation
NASLOT
CERTIFIED
SA
YF A S Y S T E
MS
CE
R T I F I C A TE
NASLOT
CERTIFIED
Certificate
PASS ✔
3Months
in harsh environments
041
d
12 Months
From date of installation
3Months
in harsh environments
d
For any technical queries please call our adviceline on 0845 241 9102
For any technical queries please call our adviceline on 0845 241 9102
COMPONENT PART DETAILS: Profiled upright SRP1100 Extruded handrail tube SRHE5000
Concrete base 25kg SRCB300 Sentry Rail system SRH5000 BIM No: SpecEquip_RfSftySymFreStdAluHndRail_SayfaSystems_ SRH5000_M3_G2
PAYLOAD SENTRYRAIL FREE STANDING HANDRAIL
041
FIXING DETAILS:Installed on flat membrane roof
PAYLOAD SENTRYRAIL FREE STANDING HANDRAIL
MEMBRANE TO CLIENT SPECIFICATION
1100
LOW PROFILECONCRETE COUNTER BALANCESUPPORT FOOT PLATE
450
EXTRUDED ALUMINIUM HANDRAIL
PROFILED ALUMINIUM UPRIGHT SUPPORT
ROOF ANGLE 10° MAXIMUM
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™SENTRY RAIL FIXEDTO FLAT MEMBRANEROOF
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
041
For any technical queries please call our adviceline on 0845 241 9102
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Installed on green roof
PAYLOAD SENTRYRAIL FREE STANDING HANDRAIL
CLEAR OUT SEDUM &GROWTH UNDER SUPPORT PLATE & COUNTER BALANCE
1100
LOW PROFILECONCRETE COUNTER BALANCESUPPORT FOOT PLATE
450
EXTRUDED ALUMINIUM HANDRAIL
PROFILED ALUMINIUM UPRIGHT SUPPORT
ROOF ANGLE 10° MAXIMUM
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™SENTRY RAIL FIXEDTO GREEN ROOF
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
041
FIXING DETAILS: Installed on gravel roof
PAYLOAD SENTRYRAIL FREE STANDING HANDRAIL
CLEAR GRAVELUNDER SUPPORT PLATE & COUNTER BALANCE
1100
LOW PROFILECONCRETE COUNTER BALANCESUPPORT FOOT PLATE
450
EXTRUDED ALUMINIUM HANDRAIL
PROFILED ALUMINIUM UPRIGHT SUPPORT
ROOF ANGLE 10° MAXIMUM
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™SENTRY RAIL FIXEDTO GRAVEL ROOF
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
041
For any technical queries please call our adviceline on 0845 241 9102
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS:Corner and D end configuration
PAYLOAD SENTRYRAIL FREE STANDING HANDRAIL
500
450
1500
523
1500 500 Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™SENTRY RAILCORNER & D ENDCONFIGURATION
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
041
FIXING DETAILS:Gates and toeboard configuration
PAYLOAD SENTRYRAIL FREE STANDING HANDRAIL
750
450
150
3000
3mm THICK TOEBOARD
SWING GATE WITH PADLOCK PLATE
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™SENTRY RAILCORNER & D ENDCONFIGURATION
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
041
For any technical queries please call our adviceline on 0845 241 9102
REV: 06/10/16PRODUCT DATA SHEET REPORT NO: 041 - B
PRODUCT CODE: SGH5000
SAYFAGUARDFREE STANDING HANDRAIL
041 - B SayfaGuard
Photo required
PRODUCT DESCRIPTION:The SayfaGuard handrail system is a free standing galvanised handrail system. It is designed to be installed as permanent edge protection on flat roofs and surfaces which have a pitch of less than 10 degrees. The upright posts and handrail are supplied in galvanised 42mm round tube construction. The tubes are connected with Sayfaclamp fittings so no on-site welding is required and site fabrication is kept to a minimum. The handrail is supplied to site with most sections cut to facilitate the speed of installation. Extra intermediate rails, infill panels and toe-boards can easily be added during or after installation of handrail.
Stability is provided by a cantilever counter balance weight incorporated into the leg design. Each leg weighs approximately XXkg each and can be spaced at up to 2.5m centres.
The underside of the weight is smooth to prevent damage to roof covering materials and is installed directly onto the finished roof. A rubber protective matting can be installed under the weight and front foot, but compatibility with the roof covering must be checked prior to installation.
22Kg 44Kg
2.5m 1.25m
EN 13374:2013 BS 6180:2011
PAYLOAD SAYFAGUARD FREE STANDING HANDRAIL
041
Up to a 10 degree pitch
10o
For any technical queries please call our adviceline on 0845 241 9102
For any technical queries please call our adviceline on 0845 241 9102
To fully comply with standards, it is necessary to have an up-stand on the edge of a roof of at least 150mm to prevent tools and equipment falling over the edge. If no roof up-stand is present the handrail must be fitted with toe-boards to provide this protection. The handrail will be a minimum 1100mm high and the handrail centres will not exceed 450mm.
Involving our design team early in the construction phase will ensure that the most cost effective and safe system is installed. Our designers will consider the safety of both installers during the construction phase and future maintenance personnel.
1100mm
450mmgap
150mmToeboard optional
PAYLOAD SAYFAGUARD FREE STANDING HANDRAIL
SayfaGuard has purpose made corners and D Ends. These parts have been engineered to a high degree of accuracy and provide a smooth change in direction on corners and at an end of a run.
Self-closing swing gates are available as standard with a spring return latch and provision to be able to secure with a padlock to prevent unauthorized access to certain areas.
D Ends Swing gateCorners
041
The SentryRail handrail is lightweight yet extremely strong. The aluminium handrail sections are normally supplied to site in 5.0m or 3.0m lengths. A 5.0m section weighs less than 1kg per metre. The benefits during installation are reduced manual handling issues and reduced installation time.
SentryRail can be supplied and installed as a basic handrail edge protection compliant with current legislation or can be provided with optional extras to enhance the system to suit a budget. Handrail can be Polyester powder Coated to match most RAL colour requirements. Colour coding is not recommended in areas of high usage or in harsh environments. Infill panels or fence panels can be fitted to provide added protection or a screen to block visibility of roof plant from the ground.
A complete installed SentryRail system can weigh as little as 19kg per linear metre, with a point load of 24Kg. The system therefore has a very impressive safety to weight ratio, which is particularly important on modular or lightweight roof systems where reduced loading applies.
Infill panel designs can be made to most specifications and requirements. It is possible to design the system to accommodate fence panels or aluminium louvres to match existing building work. All SentryRail systems that are to be fitted with any form of infill panel will need careful design input to ensure wind loading calculations have been assessed and accounted for.
19Kg/m2 47Kg/m2
EN 13374:2013
Infill panel Fence panel Louvre panel Security mesh panel
BS 6180:2011
Point load 24Kg Point load 48Kg
PAYLOAD SAYFAGUARD FREE STANDING HANDRAIL
041
For any technical queries please call our adviceline on 0845 241 9102
For any technical queries please call our adviceline on 0845 241 9102
Yield 275 N/mm² C 0.15 – 0.26; Si < 0.35; Mn < 1.5; P < 0.035; S <
0.040; Mo 0.4 – 0.6.
Young’s Modulus of Elasticity 200 x 103 MPa at 20 °C
Density 7.87 g/cm3 at 20 °C
Coefficient of Thermal Expansion Low-Carbon/HSLAS: 12.4 μm/m/°C in 20 °C to 100 °C range I-F
Steel: 12.9 μm/m/°C in 20 °C to 100 °C range
Thermal Conductivity Low-Carbon/HSLAS: 89 W/m°C at 20°C I-F Steel:
93 W/m°C at 20°C
Specific Heat 481 J/kg/°C in 50 °C to 100 °C range
Electrical Resistivity 0.142 μΩ•m at 20 °C
Aluminium louvres (if required) Aluminium extrusion 0.50 - 0.75 Si, Max 0.35, Fe 0.40 - 0.70 Mg Tensile strength PSI 23,000 Yield strength PSI 15,000
MATERIAL SPECIFICATION:
Brackets - galvanised steel
payloaD sayfaguaRD fixeD hanDRail
Galvanised tube
Galvanised fittings
Galvanised base plate
042
For any technical queries please call our adviceline on 0845 241 9102
payloaD sayfaguaRD fixeD hanDRail
OPERATING AND DESIGN STANDARDS:Eurocodes are designated by EN British standards are designated by BS
• BS 6180:2011• BS EN 12020-1 and 2 :2008 Aluminium and
Aluminium alloy extrusions• BS EN 755:2008 series Extruded profiles• BS EN 754: 2008 series Tolerances on dimensions
extruded profiles• BS 1154:2003- Physical and compositional
properties for natural black rubber• ISO 9001:2008• ISO 14001:2004• BS OHSAS 18001:2007• Work at height regulations 2005 (Ref.7)• Work at height (amendment) Regulations
✔
BS ENISO
Standards
2007 (Ref.8) WAHR• Provision and use of work equipment regulations1998 PUWER 98 (Ref. 5)• Management of health and safety at workregulations 1999 MHSWR (Ref.2)• The Building Regulations 2010 part K.
Note: For guidelines only to be checked by Chief Engineer.
Ultimate serviceability loads BS 6180:2011
Static load
Deflection(Non-permanent)
Overturning
Regular maintenance usage
0.36kN 3.7kN/m
0.36kN
0.5kN
25mm
042
The company operates to the following standards
For any technical queries please call our adviceline on 0845 241 9102
Maintenance to be in accordance with SIMS standards. (details available on request)
Maintenance to be carried out at time of yearly inspection.
Contact Sayfa Systems to arrange system maintenance.
TRAINING REQUIREMENTS:All personnel who use the Aviator system should have attended a NASLOT (National Access and Safety Line Operator Training) course. Courses are available from Sayfa Systems UK Ltd.
INSPECTION/MAINTENANCE/TRAINING
INSPECTION ROUTINE:All systems to be inspected at least every 12 months from date of installation.
In harsh environments all systems to be inspected at least every 3 months.
Inspections must be carried out by approved Aviator engineers.
Inspections must be approved to SIMS (Safety Inspection and Maintenance Service) standards.
All inspections to be carried out to EN795:2012 and BS 7883:2005 and WAHSA (inspection of eyebolts) requirements for safety line and anchor points.
All inspections to be carried out to EN364 requirements for personal protective equipment.
Contact Sayfa Systems to arrange inspections.
MAINTENANCE SCHEDULE:All maintenance to be carried out by approved Aviator engineers.
Maintenance to be in accordance with Sayfa Systems UK (manufacturer) guidelines and recommendations.
In harsh environments all systems to be inspected at least every 3 months.
12 Months
From date of installation
NASLOT
CERTIFIED
3Months
in harsh environments
d
Sa
yfa
SyStem
S
Ce
R t I f I C a
te
NASLOT
CERTIFIED
Certificate
PASS ✔
12 Months
From date of installation
3Months
in harsh environments
d
payloaD sayfaguaRD fixeD hanDRail
042
For any technical queries please call our adviceline on 0845 241 9102
payloaD sayfaguaRD fixeD hanDRail
FIXING DETAILS:Gates and toeboard configuration
750
450
150
3000
3mm THICK TOEBOARD
SWING GATE WITH PADLOCK PLATE
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™SAYFAGUARDCORNER & D ENDCONFIGURATION
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
042
DATE: 28/10/2014
BIM LOCATION: DWG 0042/28/10 REV 1
PRODUCT DATA SHEET REPORT NO: 042
PRODUCT CODE: SGH5000
SAYFAGUARD FIXED HANDRAIL
042
For any technical queries please call our adviceline on 0845 241 9102
PRODUCT DESCRIPTION:The Sayfaguard handrail system is designed to be installed as permanent edge protection on roofs and surfaces which have a pitch of up to 45 degrees. The upright posts and handrail are supplied in galvanised 42mm round tube construction. The tubes are connected with Sayfaclamp fittings so no on-site welding is required and site fabrication is kept to a minimum. The handrail is supplied to site with most sections cut to facilitate the speed of installation. Extra intermediate rails, infill panels and toeboards can easily be added during or after installation of handrail.
The Sayfaguard base plates are designed to be fixed to the roof or floor substrate with suitable fixings to accommodate the necessary forces as determined in the industry standards. If additional stability is required then outriggers can be installed. These may be needed when using infill panels to ensure that they will be
suitable for the additional wind loads which will be applied. Depending on the structure that it will be fixed to, the handrail uprights can be spaced at 2,25m centres. All handrail can be colour coded if required to match the roof finish. This is not recommended in aggressive atmospheres or high use areas.
2.25m
Up to a 45 degree pitch
Outrigger if requiredHandrail uprights spaced at 2,25m centres
45o
PAYLOAD SAYFAGUARD FIXED HANDRAIL
042
For any technical queries please call our adviceline on 0845 241 9102
To fully comply with standards, it is necessary to have an up-stand on the edge of a roof of at least 100mm to prevent tools and equipment falling over the edge. If no roof up-stand is present the handrail must be fitted with toeboards to provide this protection. The handrail will be a minimum 1100mm high and the handrail centres will not exceed 450mm. Involving
our design team early in the construction phase will ensure that the most cost effective and safe system is installed. Our designers will consider the safety of both installers during the construction phase and future maintenance personal.
1100mm
450mmgap
100mmToeboard optional
PAYLOAD SAYFAGUARD FIXED HANDRAIL
SentryRail has purpose made corners and D Ends. These parts have been plastic injection moulded to a high degree of accuracy and provide a smooth change in direction on corners and an end of a run. Swing gates are available and can be provided with or lock to prevent unauthorized access to certain areas.
When fixing direct to steel deck roofs the base plates will be fitted with a butile mastic sealing strip between the bracket and the roof deck. This sealing strip provides a guaranteed leak free seal. Sayfaguard base plates for steel roof fixing are larger with more fixing holes to accommodate Sayfa bulb type rivets, which have an integrated neoprene seal for added protection.
Weather capSayfa bulb type rivet
Butile mastic seal
Roof substrate
Roof build up Steel roof deck
150mm
042
For any technical queries please call our adviceline on 0845 241 9102
For standing seam roofs specialist Sayfaclamps are incorporated into the base plate. This will ensure that the roof deck does not need to be penetrated in any way. Base plates for standing seam roofs can be manufactured to accommodate up to a 500mm seam centre. Larger seams will require the use of spreader plates if the base cannot be fixed in the valley.
PAYLOAD SAYFAGUARD FIXED HANDRAIL
500mmWider than
500mm
Infill panel Fence panel Louvre panel Security mesh panel
Sayfaguard can be supplied and installed as a basic handrail edge protection compliant with current legislation or can be provided with optional extras to enhance the system to suit a budget. Handrail can be Polyester powder Coated to match most RAL colour requirements. Colour coding is not recommended in areas of high usage or in harsh environments. Infill panels or fence panels can be fitted to provide added protection or a screen to block visibility
of roof plant from the ground. Infill panel designs can be made to most specifications and requirements. It is possible to design the system to accommodate wooden fence panels or aluminium louvres to match existing building work. All SentryRail systems that are to be fitted with any form of infill panel will need careful design input to ensure wind loading calculations have been assessed and accounted for.
042
For any technical queries please call our adviceline on 0845 241 9102
Swing gates with locks are available for use on designated access points. Gates are supplied in galvanized steel tube and fittings. The end of a run can be supplied with a D style connector and corners and variable corners are easily achieved with the range of Sayfaclamp fittings.
PAYLOAD SAYFAGUARD FIXED HANDRAIL
D Ends Swing gateCorners
042
For any technical queries please call our adviceline on 0845 241 9102
Yield 275 N/mm² C 0.15 – 0.26; Si < 0.35; Mn < 1.5; P < 0.035; S <
0.040; Mo 0.4 – 0.6.
Young’s Modulus of Elasticity 200 x 103 MPa at 20 °C
Density 7.87 g/cm3 at 20 °C
Coefficient of Thermal Expansion Low-Carbon/HSLAS: 12.4 μm/m/°C in 20 °C to 100 °C range I-F
Steel: 12.9 μm/m/°C in 20 °C to 100 °C range
Thermal Conductivity Low-Carbon/HSLAS: 89 W/m°C at 20°C I-F Steel:
93 W/m°C at 20°C
Specific Heat 481 J/kg/°C in 50 °C to 100 °C range
Electrical Resistivity 0.142 μΩ•m at 20 °C
Aluminium louvres (if required) Aluminium extrusion 0.50 - 0.75 Si, Max 0.35, Fe 0.40 - 0.70 Mg Tensile strength PSI 23,000 Yield strength PSI 15,000
MATERIAL SPECIFICATION:
Brackets - galvanised steel
PAYLOAD SAYFAGUARD FIXED HANDRAIL
Galvanised tube
Galvanised fittings
Galvanised base plate
042
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD SAYFAGUARD FIXED HANDRAIL
OPERATING AND DESIGN STANDARDS:Eurocodes are designated by EN British standards are designated by BS
• BS 6180:2011• BS EN 12020-1 and 2 :2008 Aluminium and
Aluminium alloy extrusions• BS EN 755:2008 series Extruded profiles• BS EN 754: 2008 series Tolerances on dimensions
extruded profiles• BS 1154:2003- Physical and compositional
properties for natural black rubber• ISO 9001:2008• ISO 14001:2004• BS OHSAS 18001:2007• Work at height regulations 2005 (Ref.7)• Work at height (amendment) Regulations
✔
BS ENISO
Standards
2007 (Ref.8) WAHR• Provision and use of work equipment regulations
1998 PUWER 98 (Ref. 5)• Management of health and safety at work
regulations 1999 MHSWR (Ref.2)• The Building Regulations 2010 part K.
Note: For guidelines only to be checked by Chief Engineer.
Ultimate serviceability loads BS 6180:2011
Static load
Deflection(Non-permanent)
Overturning
Regular maintenance usage
0.36kN 3.7kN/m
0.36kN
0.5kN
25mm
042
The company operates to the following standards
For any technical queries please call our adviceline on 0845 241 9102
Maintenance to be in accordance with SIMS standards. (details available on request)
Maintenance to be carried out at time of yearly inspection.
Contact Sayfa Systems to arrange system maintenance.
TRAINING REQUIREMENTS:All personnel who use the Aviator system should have attended a NASLOT (National Access and Safety Line Operator Training) course. Courses are available from Sayfa Systems UK Ltd.
INSPECTION/MAINTENANCE/TRAINING
INSPECTION ROUTINE:All systems to be inspected at least every 12 months from date of installation.
In harsh environments all systems to be inspected at least every 3 months.
Inspections must be carried out by approved Aviator engineers.
Inspections must be approved to SIMS (Safety Inspection and Maintenance Service) standards.
All inspections to be carried out to EN795:2012 and BS 7883:2005 and WAHSA (inspection of eyebolts) requirements for safety line and anchor points.
All inspections to be carried out to EN364 requirements for personal protective equipment.
Contact Sayfa Systems to arrange inspections.
MAINTENANCE SCHEDULE:All maintenance to be carried out by approved Aviator engineers.
Maintenance to be in accordance with Sayfa Systems UK (manufacturer) guidelines and recommendations.
In harsh environments all systems to be inspected at least every 3 months.
12 Months
From date of installation
NASLOT
CERTIFIED
3Months
in harsh environments
d
Sa
yfa
SyStem
S
Ce
R t I f I C a
te
NASLOT
CERTIFIED
Certificate
PASS ✔
12 Months
From date of installation
3Months
in harsh environments
d
PAYLOAD SAYFAGUARD FIXED HANDRAIL
042
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD SAYFAGUARD FIXED HANDRAIL
COMPONENT PART DETAILS:Post for concrete fix SGP1100CF Steel roof fix SGP1100SR
Standing seam fix SGP1100SS
Complete system SGH5000 BIM No: SpecEquip_RfSftySymFxdGlvHndRailCon_SayfaSystems_SRH5000CF_M3_G2
042
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD SAYFAGUARD FIXED HANDRAIL
FIXING DETAILS:Installed on concrete deck
140mm x 73mm x 9mmBASE PLATE
Ø42mm TUBE
Ø42mm NON WELD FITTINGS
M10 RESIN ANCHORSET 100mm INCONCRETE
METAL DECKTO CLIENT SPECIFICATION
MINIMUM 150mm THICKCAST CONCRETE SLAB
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™SAYFAGUARDFIXED TO CONCRETEROOF DECK
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
042
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD SAYFAGUARD FIXED HANDRAIL
FIXING DETAILS:Installed on steel roof deck
540mm x 230mm x 4mmBASE PLATE
Ø42mm TUBE
Ø42mm NON WELD FITTINGS
10nr ROOFING SCREWSTO SUIT ROOF DECK
THIS FIXING DETAIL IS CORRECT FOR PEAK CENTRES UP TO 400mm
ROOF DECK TO CUSTOMERS SPECIFICATION
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™SAYFAGUARDFIXED TO STEELROOF DECK
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
042
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS:Installed standing seam roof
PAYLOAD SAYFAGUARD FIXED HANDRAIL
600mm x 600mm x 4mmBASE PLATE
Ø42mm TUBE
Ø42mm NON WELD FITTINGS
2nr M8 FIXING BOLTSPER SEAM CLAMP
THIS FIXING DETAIL IS CORRECT FOR PEAK CENTRES UP TO 500mmROOF DECK TOCUSTOMERSSPECIFICATION
ALUMINUMNON-PENETRATING STANDING
SEAM CLAMPS
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™SAYFAGUARDFIXED TO STANDINGSEAM ROOF DECK
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
042
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD SAYFAGUARD FIXED HANDRAIL
FIXING DETAILS:Gates and toeboard configuration
750
450
150
3000
3mm THICK TOEBOARD
SWING GATE WITH PADLOCK PLATE
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™SAYFAGUARDCORNER & D ENDCONFIGURATION
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
042
For any technical queries please call our adviceline on 0845 241 9102
DATE: 28/10/2014PRODUCT DATA SHEET REPORT NO: 051
PRODUCT CODE: LD400SC
FIXED ACCESS LADDERSSAFETY CAGE
051
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD FIXED ACCESS LADDERS - SAFETY CAGE
PRODUCT DESCRIPTION:The Payload fixed access ladders are designed to provide a permanent means of safe access to a roof or platform. The ladders are provided with a round safety cage to limit the risk of a person falling from the ladder. It is important to note that it may still be possible to fall from this ladder and should a higher degree of safety be required a vertical safety line with
line shuttle should be fitted. The safety cage is designed to start from 2.2m up to 3m from the ladder base and must run at least 1.1m above the ladder platform. This is to allow personal access underneath the cage. The ladder rungs at the base can be fitted with a Sayfa rung cover to prevent unauthorised access.
1,1m
2,2mto 3m
Rung cover
051
For any technical queries please call our adviceline on 0845 241 9102
The maximum climbing height for a single ladder is 10m. Should the ladder extend over 10m then the individual ladder heights must be 6m or less. The flights must be staggered and have a rest platform of at least 700mm square. Handrail must be provided around the platform at 1100mm for the top rail and a gap of no more than 450mm for the intermediate
handrail. A 100mm toe-board must be fitted on the platform. If it is not possible to fit an intermediate platform – such as on chimneys- a single ladder of greater than 10m can be fitted but must be installed with a vertical safety line instead of a safety cage.
10mMaximum
More than 10m
6mMaximum
PAYLOAD FIXED ACCESS LADDERS - SAFETY CAGE
The rungs on each ladder are uniformly spaced at centres between 225mm and 255mm. The last rung is replaced with the ladder platform on the ladder head. Rungs and platforms are capable of supporting
a mass of 150kg spread over 100mm. The distance between the stiles is normally between 400mm to 600mm. It is possible to go to 300mm between stiles if space is limited.
400-600mm
150Kg150Kg
Same as rung spacing
051
225mm -255mm Centres
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD FIXED ACCESS LADDERS - SAFETY CAGE
The ladder heads provide an opening at the top of the ladder of 600-700mm. Sayfa ladder gates can be fitted for added security and safety. The ladder heads extend 1.1m above the ladder platform. The ladder platform and handrail are normally 600mm long. Should the platform be required to be longer it will be necessary to extend the platform onto
The distance between the fixing brackets is a maximum of 2.0m between the fixing centres. It is important that the fixing bracket can withstand a vertical load of 3Kn and each fixing withstand a 0.5Kn pull-out load. When fixing to sheet steel the use of a spreader plate will facilitate these forces. Our designers will be able to advise on fixing details. The brackets must be designed to ensure there is a minimum of 150mm clear space behind each rung to ensure sufficient area for an operatives foot to stand on.
the roof or platform and support the platform at the extended end with a base. In some circumstances the roof may drop down onto the upper roof. If this drop down is more than 300mm than a ladder section will need to be fitted.
Optional gate Standard ladderhead Extended platform ladderhead
600-700mm 600mm 1000mm
1.1m
300 mm
2.0mMaximum
150mmMinimum stand off
0.5kN
3kN
051
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD FIXED ACCESS LADDERS - SAFETY CAGE
Permanent fixed ladders can be manufactured and supplied in galvanized steel or aluminium. Traditionally galvanized ladders are specified but aluminium ladders are now also used extensively. Both types comply with current legislation. Galvanized ladders are more cost effective to produce but due to the weight are more difficult to
When a permanent ladder is installed underneath an access hatch it is necessary to fit a Sayfa grab rail on the top rungs. The grab rail can be extended up very easily and quickly once the access hatch has been opened. This provides a single handrail for safe access onto and off the roof. It is very easily retracted
deliver to site and install. Both types of ladders are supplied in modular components to assist with manual handling issues on site. On larger ladders it will be necessary to have suitable lifting equipment in the form of a crane or MEWP to assemble and install on site.
when closing the roof hatch. In added safety and security the Payload free standing handrail can be fitted around the roof hatch with a safety gate. This will prevent any unauthorized access when in use and prevent any fall risk from the open roof hatch.
Ladder section Ladder section with cage
Ladder head with cage
Extended platform
Galvanised/ aluminium
Access closedArm retracted
Access openArm extended Access closed
Gate closedAccess open
Gate open
Galvanised/ aluminium
Galvanised/ aluminium
Galvanised/ aluminium
051
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD FIXED ACCESS LADDERS - SAFETY CAGE
Yield 275 N/mm² C 0.15 – 0.26; Si < 0.35; Mn < 1.5; P < 0.035; S < 0.040; Mo 0.4 – 0.6.
Young’s Modulus of Elasticity 200 x 103 MPa at 20 °C
Density 7.87 g/cm3 at 20 °C
Coefficient of Thermal Expansion Low-Carbon/HSLAS: 12.4 μm/m/°C in 20 °C to 100 °C range I-F Steel: 12.9 μm/m/°C in 20 °C to 100 °C range
Thermal Conductivity Low-Carbon/HSLAS: 89 W/m°C at 20°C I-F Steel: 93 W/m°C at 20°C
Specific Heat 481 J/kg/°C in 50 °C to 100 °C range
Electrical Resistivity 0.142 μΩ•m at 20 °C
Galvanised steel profile
MATERIAL SPECIFICATION:
Aluminium profileAluminium extrusion 0.50 - 0.75 Si, Max 0.35, Fe 0.40 - 0.70 MgTensile strength PSI 23,000 Yield strength PSI 15,000
Natural rubber base CIS14 Polyisoprene - Optional
Durometer (Shore A) 30-90Specific Gravity (Polymer) 0.92Tensile Strength Max-psi (Mpa) 3500 (24.1)Low Temperature Brittle Point (C/F) -58/-70Tear Strength EFlame Retardent Properties PSealing Characteristics P
Galvanised Galvanisedfixings
Stainlesssteelfixings
Aluminium
Rubber base
051
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD FIXED ACCESS LADDERS - SAFETY CAGE
Typical connection loads (Maximum cantilever from substrate 250mm)
Vertical shear
Uniform load 100mm2
Tension
Maximum SWL
3Kn 0.5Kn
150Kg 450Kg
Note: For guidelines only to be checked by Chief Engineer.
OPERATING AND DESIGN STANDARDS:Eurocodes are designated by EN British standards are designated by BS
• BS4211:2005+A1:2008• BS EN 12020-1 and 2 :2008 Aluminium and
Aluminium alloy extrusions• BS EN 755:2008 series Extruded profiles• BS EN 754: 2008 series Tolerances on dimensions
extruded profiles• BS 1154:2003- Physical and compositional
properties for natural black rubber• ISO 9001:2008• ISO 14001:2004• BS OHSAS 18001:2007• Work at height regulations 2005 (Ref.7)
✔
BS ENISO
Standards
• Work at height (amendment) Regulations2007 (Ref.8) WAHR
• Provision and use of work equipment regulations1998 PUWER 98 (Ref. 5)
• Management of health and safety at workregulations 1999 MHSWR (Ref.2)
• The Building Regulations 2010 part K.
051
The company operates to the following standards
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD FIXED ACCESS LADDERS - SAFETY CAGE
Maintenance to be in accordance with SIMS standards. (details available on request)
Maintenance to be carried out at time of yearly inspection.
Contact Sayfa Systems to arrange system maintenance.
TRAINING REQUIREMENTS:All personnel who use the Aviator system should have attended a NASLOT (National Access and Safety Line Operator Training) course. Courses are available from Sayfa Systems UK Ltd.
INSPECTION/MAINTENANCE/TRAINING
INSPECTION ROUTINE:All systems to be inspected at least every 12 months from date of installation.
In harsh environments all systems to be inspected at least every 3 months.
Inspections must be carried out by approved Aviator engineers.
Inspections must be approved to SIMS (Safety Inspection and Maintenance Service) standards.
All inspections to be carried out to EN795:2012 and BS 7883:2005 and WAHSA (inspection of eyebolts) requirements for safety line and anchor points.
All inspections to be carried out to EN364 requirements for personal protective equipment.
Contact Sayfa Systems to arrange inspections.
MAINTENANCE SCHEDULE:All maintenance to be carried out by approved Aviator engineers.
Maintenance to be in accordance with Sayfa Systems UK (manufacturer) guidelines and recommendations.
In harsh environments all systems to be inspected at least every 3 months.
12 Months
From date of installation
NASLOT
CERTIFIED
3Months
in harsh environments
d
Sa
yfa
SyStem
S
Ce
R t I f I C a
te
NASLOT
CERTIFIED
Certificate
PASS ✔
12 Months
From date of installation
3Months
in harsh environments
d
051
For any technical queries please call our adviceline on 0845 241 9102
COMPONENT PART DETAILS:Ladder section 2250mm LDS2250
Ladder cage section LDS2250CG
Ladder head LDH4RCG Ladder platform 1200mm LDP1200
PAYLOAD FIXED ACCESS LADDERS - SAFETY CAGE
400
2250
600
1100
7001000
1100
700
700 2250
LADDER SECTION 2250mm LDS 2250 LADDER CAGE SECTION LDS2250CG
LADDER PLATFORM LDP1000LADDER HEAD WITH CAGELDH4RCG
400
2250
600
1100
7001000
1100
700
700 2250
LADDER SECTION 2250mm LDS 2250 LADDER CAGE SECTION LDS2250CG
LADDER PLATFORM LDP1000LADDER HEAD WITH CAGELDH4RCG
400
2250
600
1100
7001000
1100
700
700 2250
LADDER SECTION 2250mm LDS 2250 LADDER CAGE SECTION LDS2250CG
LADDER PLATFORM LDP1000LADDER HEAD WITH CAGELDH4RCG
400
2250
600
1100
7001000
1100
700
700 2250
LADDER SECTION 2250mm LDS 2250 LADDER CAGE SECTION LDS2250CG
LADDER PLATFORM LDP1000LADDER HEAD WITH CAGELDH4RCG
051
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD FIXED ACCESS LADDERS - SAFETY CAGE
COMPONENT PART DETAILS:Ladder bracket 300mm LDB300
Ladder base LDB600
Rung cover LRC1200 Swing gate LSG700
40
400
480
2100
650
800
SPRING LOADEDHINGES OPTIONAL
PADLOCK PLATE
100
LADDER BRACKET LDB300 LADDER BASE LDB600
SWING GATE LSG650RUNG COVER LRC120040
400
480
2100
650
800
SPRING LOADEDHINGES OPTIONAL
PADLOCK PLATE
100
LADDER BRACKET LDB300 LADDER BASE LDB600
SWING GATE LSG650RUNG COVER LRC1200
40
400
480
2100
650
800
SPRING LOADEDHINGES OPTIONAL
PADLOCK PLATE
100
LADDER BRACKET LDB300 LADDER BASE LDB600
SWING GATE LSG650RUNG COVER LRC1200
40
400
480
2100
650
800
SPRING LOADEDHINGES OPTIONAL
PADLOCK PLATE
100
LADDER BRACKET LDB300 LADDER BASE LDB600
SWING GATE LSG650RUNG COVER LRC1200
051
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS:LD400L9 fixed to concrete/brickwork BIM No: SpecEquip_RfSftySymFxdLdrCgePltfm_SayfaSystems_LD400L9_M3_G2
PAYLOAD FIXED ACCESS LADDERS - SAFETY CAGE
600
1100
700
BE
TWE
EN
2.2
m &
3.0
m
MINIMUM150mm
MA
XIM
UM
2.0
m C
EN
TRE
S
ALUMINUM OR GALVANISEDCONSTRUCTION TOSUIT CUSTOMERSPECIFICATION
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ LD400/L9SAFETY CAGE ACCESSLADDER FIXED TOBLOCK WORK
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
NON - PENETRATING RUBBER BASE
M10 RESIN ANCHOR SET 80mm INBLOCKWORK.MINIMUM 3 FIXINGS PER BRACKET
051
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS:LD400L9 fixed to steel cladding BIM No: SpecEquip_RfSftySymFxdLdrCgePltfm_SayfaSystems_LD400L9_M3_G2
PAYLOAD FIXED ACCESS LADDERS - SAFETY CAGE
600
1100
700
BE
TWE
EN
2.2
m &
3.0
m
MINIMUM150mm
MA
XIM
UM
1.5
m C
EN
TRE
S
ALUMINUM OR GALVANISEDCONSTRUCTION TOSUIT CUSTOMERSPECIFICATION
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ LD400/L9SAFETY CAGE ACCESSLADDER FIXED TOSTEEL CLADDING
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
NON - PENETRATING RUBBER BASE
CLADDINGTO CLIENTSSPECIFICATION
3x TOGGLEFIXINGS PERBRACKET
SEALINGBUTILEMASTIC
051
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAIL: LD400L11 fixed to concrete/brickwork 300mm bracket - BIM No: SpecEquip_RfSftySymFxdLdrCge_SayfaSystems_LD400L11300_M3_G2
500mm bracket - BIM No: SpecEquip_RfSftySymFxdLdrCge_SayfaSystems_LD400L11500_M3_G2
PAYLOAD FIXED ACCESS LADDERS - SAFETY CAGE
BE
TWE
EN
2.2
m &
3.0
m
MINIMUM150mm
MA
XIM
UM
2.0
m C
EN
TRE
S
ALUMINUM OR GALVANISEDCONSTRUCTION TOSUIT CUSTOMERSPECIFICATION
HATCH OPENINGTO BE A MINIMUM 1m²
EXTENDABLE HANDRAILTO EXTEND A MINIMUM 1mABOVE LAST LADDER RUNG
HATCH OPENINGTHIS DIRECTION
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ LD400/L11SAFETY CAGE ACCESSLADDER FIXED TOBLOCK WORK
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
NON - PENETRATING RUBBER BASE
M10 RESIN ANCHOR SET 80mm INBLOCKWORK.MINIMUM 3 FIXINGS PER BRACKET
051
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAIL: LD400L11 fixed to steel cladding 300mm bracket - BIM No: SpecEquip_RfSftySymFxdLdrCge_SayfaSystems_LD400L11300_M3_G2
500mm bracket - BIM No: SpecEquip_RfSftySymFxdLdrCge_SayfaSystems_LD400L11500_M3_G2
PAYLOAD FIXED ACCESS LADDERS - SAFETY CAGE
BE
TWE
EN
2.2
m &
3.0
m
MINIMUM150mm
MA
XIM
UM
2.0
m C
EN
TRE
S
ALUMINUM OR GALVANISEDCONSTRUCTION TOSUIT CUSTOMERSPECIFICATION
HATCH OPENINGTO BE A MINIMUM 1m²
EXTENDABLE HANDRAILTO EXTEND A MINIMUM 1mABOVE LAST LADDER RUNG
HATCH OPENINGTHIS DIRECTION
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ LD400/L11SAFETY CAGE ACCESSLADDER FIXED TOSTEEL CLADDING
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
NON - PENETRATING RUBBER BASE
SEALINGBUTILEMASTIC
3x TOGGLEFIXINGSPER BRACKET
CLADDINGTO CLIENTSSPECIFICATION
051
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAIL: LD400L13 fixed to concrete/brickwork BIM No: SpecEquip_RfSftySymFxdLdrCgePltfmStpDn_SayfaSystems_LD400L13_M3_G2
PAYLOAD FIXED ACCESS LADDERS - SAFETY CAGE
1000
1100
700
BE
TWE
EN
2.2
m &
3.0
m
MINIMUM150mm
MA
XIM
UM
2.0
m C
EN
TRE
S
ALUMINUM OR GALVANISEDCONSTRUCTION TOSUIT CUSTOMERSPECIFICATION
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ LD400/L13SAFETY CAGE ACCESSLADDER FIXED TOBLOCK WORK
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
NON - PENETRATING RUBBER BASE
M10 RESIN ANCHOR SET 80mm INBLOCKWORK.MINIMUM 3 FIXINGS PER BRACKET
051
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAIL: LD400L13 fixed to steel cladding BIM No: SpecEquip_RfSftySymFxdLdrCgePltfmStpDn_SayfaSystems_LD400L13_M3_G2
PAYLOAD FIXED ACCESS LADDERS - SAFETY CAGE
1000
1100
700
BE
TWE
EN
2.2
m &
3.0
m
MINIMUM150mm
MA
XIM
UM
1.5
m C
EN
TRE
S
ALUMINUM OR GALVANISEDCONSTRUCTION TOSUIT CUSTOMERSPECIFICATION
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ LD400/L13SAFETY CAGE ACCESSLADDER FIXED TOSTEEL CLADDING
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
NON - PENETRATING RUBBER BASE
CLADDINGTO CLIENTSSPECIFICATION
3x TOGGLEFIXINGSPER BRACKET
SEALINGBUTILEMASTIC
051
For any technical queries please call our adviceline on 0845 241 9102
DATE: 28/10/2014PRODUCT DATA SHEET REPORT NO: 052
PRODUCT CODE: LD400SL
FIXED ACCESS LADDERSSAFETY LINE
052
For any technical queries please call our adviceline on 0845 241 9102
Vertical Safety Line fitted on ladder style
PAYLOAD FIXED ACCESS LADDERS - SAFETY LINE
PRODUCT DESCRIPTION:The Payload fixed access ladders are designed to provide a permanent means of safe access to a roof or platform. The ladders are provided with a vertical safety line to limit the risk of a person falling from the ladder. The operator attaches to the safety line with a vertical line shuttle which is attached the front connection on a full body harness. The vertical
line shuttle allows the operator to climb up and down the full extent of a straight run without disconnecting. Should the operator slip or trip the line shuttle will lock up and prevent a fall. The ladder rungs at the base can be fitted with a Sayfa rung cover to prevent unauthorised access during and after use.
1.2mMinimum
052
For any technical queries please call our adviceline on 0845 241 9102
The maximum climbing height for a single ladder is 10m. Should the ladder extend over 10m then the individual ladder heights must be 6m or less. The flights must be staggered and have a rest platform of at least 700mm square. Handrail must be provided around the platform at 1100mm for the top rail
and a gap of no more than 450mm for the intermediate handrail. A 100mm toe-board must be fitted on the platform. If it is not possible to fit an intermediate platform in restricted areas – such as on chimneys- a single ladder of greater than 10m can be fitted.
10mMaximum
More than 10m
6mMaximum
PAYLOAD FIXED ACCESS LADDERS - SAFETY LINE
The rungs on each ladder are uniformly spaced at centres between 225mm and 255mm. The last rung is replaced with the ladder platform on the ladder head. Rungs and platforms are capable of supporting
a mass of 150kg spread over 100mm. The distance between the stiles is normally between 400mm to 600mm. It is possible to go to 300mm between stiles if space is limited.
225mm -255mm Centres
400-600mm
150Kg150Kg
Same as rung spacing
052
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD FIXED ACCESS LADDERS - SAFETY LINE
The ladder heads provide an opening at the top of the ladder of 600-700mm. Sayfa ladder gates can be fitted for added security and safety. The ladder heads extend 1.1m above the ladder platform. The ladder platform and handrail are normally 600mm long. Should the platform be required to be longer it will be necessary to extend the platform onto
The distance between the fixing brackets is a maximum of 2.0m between the fixing centres. It is important that the fixing bracket can withstand a vertical load of 3Kn and each fixing withstand a 0.5Kn pull-out load. When fixing to sheet steel the use of a spreader plate will facilitate these forces. Our designers will be able to advise on fixing details. The brackets must be designed to ensure there is a minimum of 150mm clear space behind each rung to ensure sufficient area for an operatives foot to stand on.
the roof or platform and support the platform at the extended end with a base. In some circumstances the roof may drop down onto the upper roof. If this drop down is more than 300mm than a ladder section will need to be fitted.
Optional gate Standard ladderhead Extended platform ladderhead
600-700mm 600mm 1000mm
1.1m
300 mm
2.0mMaximum
150mmMinimum stand off
0.5kN
3kN
052
For any technical queries please call our adviceline on 0845 241 9102
Permanent fixed ladders can be manufactured and supplied in galvanized steel or aluminium. Traditionally galvanized ladders are specified but aluminium ladders are now also used extensively. Both types comply with current legislation. Galvanized ladders are more cost effective to produce but due to the weight are more difficult to
deliver to site and install. Both types of ladders are supplied in modular components to assist with manual handling issues on site. On larger ladders it will be necessary to have suitable lifting equipment in the form of a crane or MEWP to assemble and install on site.
Ladder section Ladder head Extended platform
Galvanised/ aluminium Galvanised/
aluminium
Galvanised/ aluminium
PAYLOAD FIXED ACCESS LADDERS - SAFETY LINE
When a permanent ladder is installed underneath an access hatch it is necessary to fit a Sayfa grab rail on the top rungs. The grab rail can be extended up very easily and quickly once the access hatch has been opened. This provides a single handrail for safe access onto and off the roof. It is very easily retracted
when closing the roof hatch. In added safety and security the Payload free standing handrail can be fitted around the roof hatch with a safety gate. This will prevent any unauthorized access when in use and prevent any fall risk from the open roof hatch.
Access closedArm retracted
Access openArm extended Access closed
Gate closedAccess open
Gate open
052
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD FIXED ACCESS LADDERS - SAFETY LINE
Yield 275 N/mm² C 0.15 – 0.26; Si < 0.35; Mn < 1.5; P < 0.035; S < 0.040; Mo 0.4 – 0.6.
Young’s Modulus of Elasticity 200 x 103 MPa at 20 °C
Density 7.87 g/cm3 at 20 °C
Coefficient of Thermal Expansion Low-Carbon/HSLAS: 12.4 μm/m/°C in 20 °C to 100 °C range I-F Steel: 12.9 μm/m/°C in 20 °C to 100 °C range
Thermal Conductivity Low-Carbon/HSLAS: 89 W/m°C at 20°C I-F Steel: 93 W/m°C at 20°C
Specific Heat 481 J/kg/°C in 50 °C to 100 °C range
Electrical Resistivity 0.142 μΩ•m at 20 °C
Galvanised steel profile
MATERIAL SPECIFICATION:
Aluminium profileAluminium extrusion 0.50 - 0.75 Si, Max 0.35, Fe 0.40 - 0.70 MgTensile strength PSI 23,000 Yield strength PSI 15,000
Natural rubber base CIS14 Polyisoprene - Optional
Durometer (Shore A) 30-90Specific Gravity (Polymer) 0.92Tensile Strength Max-psi (Mpa) 3500 (24.1)Low Temperature Brittle Point (C/F) -58/-70Tear Strength EFlame Retardent Properties PSealing Characteristics P
Galvanised ladder Stainless
steel cable/ connectors
Aluminium ladder
Stainless steel
cable/ connectors
Rubber base
052
For any technical queries please call our adviceline on 0845 241 9102
Typical connection loads (Maximum cantilever from substrate 250mm)
Vertical shear
Uniform load 100mm2
Tension
Maximum SWL
3Kn 0.5Kn
150Kg 450Kg
Note: For guidelines only to be checked by Chief Engineer.
PAYLOAD FIXED ACCESS LADDERS - SAFETY LINE
OPERATING AND DESIGN STANDARDS:Eurocodes are designated by EN British standards are designated by BS
• BS4211:2005+A1:2008• BS EN 12020-1 and 2 :2008 Aluminium and
Aluminium alloy extrusions• BS EN 755:2008 series Extruded profiles• BS EN 754: 2008 series Tolerances on dimensions
extruded profiles• BS 1154:2003- Physical and compositional
properties for natural black rubber• ISO 9001:2008• ISO 14001:2004• BS OHSAS 18001:2007• Work at height regulations 2005 (Ref.7)
✔
BS ENISO
Standards
• Work at height (amendment) Regulations2007 (Ref.8) WAHR
• Provision and use of work equipment regulations1998 PUWER 98 (Ref. 5)
• Management of health and safety at workregulations 1999 MHSWR (Ref.2)
• The Building Regulations 2010 part K.
052
The company operates to the following standards
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD FIXED ACCESS LADDERS - SAFETY LINE
Maintenance to be in accordance with SIMS standards. (details available on request)
Maintenance to be carried out at time of yearly inspection.
Contact Sayfa Systems to arrange system maintenance.
TRAINING REQUIREMENTS:All personnel who use the Aviator system should have attended a NASLOT (National Access and Safety Line Operator Training) course. Courses are available from Sayfa Systems UK Ltd.
INSPECTION/MAINTENANCE/TRAINING
INSPECTION ROUTINE:All systems to be inspected at least every 12 months from date of installation.
In harsh environments all systems to be inspected at least every 3 months.
Inspections must be carried out by approved Aviator engineers.
Inspections must be approved to SIMS (Safety Inspection and Maintenance Service) standards.
All inspections to be carried out to EN795:2012 and BS 7883:2005 and WAHSA (inspection of eyebolts) requirements for safety line and anchor points.
All inspections to be carried out to EN364 requirements for personal protective equipment.
Contact Sayfa Systems to arrange inspections.
MAINTENANCE SCHEDULE:All maintenance to be carried out by approved Aviator engineers.
Maintenance to be in accordance with Sayfa Systems UK (manufacturer) guidelines and recommendations.
In harsh environments all systems to be inspected at least every 3 months.
12 Months
From date of installation
NASLOT
CERTIFIED
3Months
in harsh environments
d
Sa
yfa
SyStem
S
Ce
R t I f I C a
te
NASLOT
CERTIFIED
Certificate
PASS ✔
12 Months
From date of installation
3Months
in harsh environments
d
052
For any technical queries please call our adviceline on 0845 241 9102
COMPONENT PART DETAILS:Ladder section 2250mm LDS2250
Vertical line kit VL6000
Ladder head LDH4R Ladder platform 1200mm LDP1200
PAYLOAD FIXED ACCESS LADDERS - SAFETY LINE
400
2250
600
1100
1000
1100
CABLE LENGTH UP TO 10m
LADDER SECTION 2250mm LDS 2250 VERTICAL LINE KIT VL10000
LADDER PLATFORM LDP1000LADDER HEAD WITHOUT CAGELDH4R
400
2250
600
1100
1000
1100
CABLE LENGTH UP TO 10m
LADDER SECTION 2250mm LDS 2250 VERTICAL LINE KIT VL10000
LADDER PLATFORM LDP1000LADDER HEAD WITHOUT CAGELDH4R
400
2250
600
1100
1000
1100
CABLE LENGTH UP TO 10m
LADDER SECTION 2250mm LDS 2250 VERTICAL LINE KIT VL10000
LADDER PLATFORM LDP1000LADDER HEAD WITHOUT CAGELDH4R
400
2250
600
1100
1000
1100
CABLE LENGTH UP TO 10m
LADDER SECTION 2250mm LDS 2250 VERTICAL LINE KIT VL10000
LADDER PLATFORM LDP1000LADDER HEAD WITHOUT CAGELDH4R
052
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD FIXED ACCESS LADDERS - SAFETY LINE
COMPONENT PART DETAILS:Ladder bracket 300mm LDB300
Ladder base LDB600
Rung cover LRC1200 Swing gate LSG700
40
400
480
2100
650
800
SPRING LOADEDHINGES OPTIONAL
PADLOCK PLATE
100
LADDER BRACKET LDB300 LADDER BASE LDB600
SWING GATE LSG650RUNG COVER LRC120040
400
480
2100
650
800
SPRING LOADEDHINGES OPTIONAL
PADLOCK PLATE
100
LADDER BRACKET LDB300 LADDER BASE LDB600
SWING GATE LSG650RUNG COVER LRC1200
40
400
480
2100
650
800
SPRING LOADEDHINGES OPTIONAL
PADLOCK PLATE
100
LADDER BRACKET LDB300 LADDER BASE LDB600
SWING GATE LSG650RUNG COVER LRC1200
40
400
480
2100
650
800
SPRING LOADEDHINGES OPTIONAL
PADLOCK PLATE
100
LADDER BRACKET LDB300 LADDER BASE LDB600
SWING GATE LSG650RUNG COVER LRC1200
052
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD FIXED ACCESS LADDERS - SAFETY LINE
FIXING DETAIL: LD400L4 fixed to concrete/brickwork BIM No: SpecEquip_RfSftySymFxdLdrLnPltfm_SayfaSystems_LD400L4_M3_G2
600
1100
MINIMUM150mm
MA
XIM
UM
2.0
m C
EN
TRE
S
ALUMINUM OR GALVANISEDCONSTRUCTION TOSUIT CUSTOMERSPECIFICATION
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ LD400/L4
SAFETY LINE ACCESSLADDER FIXED TOBLOCK WORK
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
NON - PENETRATING RUBBER BASE
M10 RESIN ANCHOR SET 80mm INBLOCKWORK.MINIMUM 3 FIXINGS PER BRACKET
8mm STAINLESSSTEEL SAFETY LINE
052
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD FIXED ACCESS LADDERS - SAFETY LINE
FIXING DETAIL: LD400L4 fixed to steel cladding BIM No: SpecEquip_RfSftySymFxdLdrLnPltfm_SayfaSystems_LD400L4_M3_G2
600
1100
MINIMUM150mm
MA
XIM
UM
1.5
m C
EN
TRE
S
ALUMINUM OR GALVANISEDCONSTRUCTION TOSUIT CUSTOMERSPECIFICATION
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ LD400/L4SAFETY LINE ACCESSLADDER FIXED TOSTEEL CLADDING
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
NON - PENETRATING RUBBER BASE
CLADDINGTO CLIENTSSPECIFICATION
3x TOGGLEFIXINGS PERBRACKET
SEALINGBUTILEMASTIC
M16 STAINLESSSTEEL EYE NUT
8mm STAINLESSSTEEL SAFETY LINE
052
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD FIXED ACCESS LADDERS - SAFETY LINE
FIXING DETAIL: LD400L7 fixed to concrete/brickwork 300mm bracket - BIM No: SpecEquip_RfSftySymFxdLdrLn_SayfaSystems_LD400L7300_M3_G2
500mm bracket - BIM No: SpecEquip_RfSftySymFxdLdrLn_SayfaSystems_LD400L7500_M3_G2
MINIMUM150mm
MA
XIM
UM
2.0
m C
EN
TRE
S
ALUMINUM OR GALVANISEDCONSTRUCTION TOSUIT CUSTOMERSPECIFICATION
HATCH OPENINGTO BE A MINIMUM 1m²
EXTENDABLE HANDRAILTO EXTEND A MINIMUM 1mABOVE LAST LADDER RUNG
HATCH OPENINGTHIS DIRECTION
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ LD400/L7SAFETY LINE ACCESSLADDER FIXED TOBLOCK WORK
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
NON - PENETRATING RUBBER BASE
M10 RESIN ANCHOR SET 80mm INBLOCKWORK.MINIMUM 3 FIXINGS PER BRACKET
M16 STAINLESSSTEEL EYE NUT
8mm STAINLESSSTEEL SAFETY LINE
052
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD FIXED ACCESS LADDERS - SAFETY LINE
FIXING DETAIL: LD400L7 fixed to steel cladding 300mm bracket - BIM No: SpecEquip_RfSftySymFxdLdrLn_SayfaSystems_LD400L7300_M3_G2
500mm bracket - BIM No: SpecEquip_RfSftySymFxdLdrLn_SayfaSystems_LD400L7500_M3_G2
MINIMUM150mm
MA
XIM
UM
1.5
m C
EN
TRE
S
ALUMINUM ORGALVANISEDCONSTRUCTION TOSUIT CUSTOMERSPECIFICATION
HATCH OPENINGTO BE A MINIMUM 1m²
EXTENDABLE HANDRAILTO EXTEND A MINIMUM 1mABOVE LAST LADDER RUNG
HATCH OPENINGTHIS DIRECTION
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ LD400/L7SAFETY LINE ACCESSLADDER FIXED TOSTEEL CLADDING
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
NON - PENETRATING RUBBER BASE
SEALINGBUTILEMASTIC
3x TOGGLEFIXINGSPER BRACKET
CLADDINGTO CLIENTSSPECIFICATION
M16 STAINLESSSTEEL EYE NUT
8mm STAINLESSSTEEL SAFETY LINE
052
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD FIXED ACCESS LADDERS - SAFETY LINE
FIXING DETAIL: LD400L8 fixed to concrete/brickwork BIM No: SpecEquip_RfSftySymFxdLdrLnPltfmStpDn_SayfaSystems_LD400L8_M3_G2
1000
1100
MINIMUM150mm
MA
XIM
UM
2.0
m C
EN
TRE
S
ALUMINUM OR GALVANISEDCONSTRUCTION TOSUIT CUSTOMERSPECIFICATION
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ LD400/L8SAFETY LINE ACCESSLADDER FIXED TOBLOCK WORK
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
NON - PENETRATING RUBBER BASE
M10 RESIN ANCHOR SET 80mm INBLOCKWORK.MINIMUM 3 FIXINGS PER BRACKET
M16 STAINLESSSTEEL EYE NUT
8mm STAINLESSSTEEL SAFETY LINE
052
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD FIXED ACCESS LADDERS - SAFETY LINE
FIXING DETAIL: LD400L8 fixed to steel cladding BIM No: SpecEquip_RfSftySymFxdLdrLnPltfmStpDn_SayfaSystems_LD400L8_M3_G2
1000
1100
MINIMUM150mm
MA
XIM
UM
1.5
m C
EN
TRE
S
ALUMINUM OR GALVANISEDCONSTRUCTION TOSUIT CUSTOMERSPECIFICATION
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ LD400/L8SAFETY LINE ACCESSLADDER FIXED TOSTEEL CLADDING
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
NON - PENETRATING RUBBER BASE
CLADDINGTO CLIENTSSPECIFICATION
3x TOGGLEFIXINGSPER BRACKET
SEALINGBUTILEMASTIC
M16 STAINLESSSTEEL EYE NUT
8mm STAINLESSSTEEL SAFETY LINE
052
For any technical queries please call our adviceline on 0845 241 9102
DATE: 28/10/2014PRODUCT DATA SHEET REPORT NO: 061
PRODUCT CODE: SO400
STEP OVERS
061
For any technical queries please call our adviceline on 0845 241 9102
PRODUCT DESCRIPTION:The Payload step over systems are designed to facilitate safe access on a designated access pathway, over pipework, roof penetrations, parapet walls and roof plant. The step overs are 800mm wide and have a platform length of 0,5m-2,0m. The maximum height of the raised step overs is 1,5. The
Payload step overs are designed as a modular system to ensure ease of installation. Depending on the size of the stairs the handrail and stringers are supplied as a complete unit. The stair treads easily bolt between the stringers and the central platform completes the product. If the site has suitable lifting
PAYLOAD STAIRS - STEPOVERS
step overs are designed to be free standing on rubber base plates which ensures that no roof or wall penetrations are required. The Step overs are designed as a permanent means of access and usually left in position throughout the duration of the access requirements. The system is supplied with handrail on both sides for added safety.
equipment it is possible to fully assemble the unit before delivering to site and then lift safely into position. The rubber base feet have an adjustment facility to ensure the stairs can remain level on surfaces that are angled at up to 10 degrees.
Height to suit customer requirements
1100mm
800mmLength to suit customer requirements
0.5 - 2.0m
Side stringer and handrail
Platform stringer and handrail
Stair treads and platform
Rubber base
061
For any technical queries please call our adviceline on 0845 241 9102
The steps are spaced at 250mm between centres and are on a 60 degree angle. The width of the stair is 242mm The stair treads all have an anti-slip nosing on the front of each step. The stair tread and platform are constructed from rectangular welded
All fixings are capable of supporting a shear load of 3Kn force and a tension force of 0,5Kn. The platform and stairs can support a weight of 150Kg spread over a 100mm area. The ultimate SWL is 450kg on each complete stair set. No more than 2 users are
PAYLOAD STAIRS - STEPOVERS
mesh. The mesh is non slip under normal working conditions. Care should be taken in extreme weather as some surfaces may become slippery. The stairs nosings can be colour coded if required for an additional cost.
allowed on each stair at any time. The step overs are designed for occasional maintenance use. Should high usage or fire access use be required our designers can advise on specific designs.
Anti slip nosing
Rectangular mesh stairs and platform
Maximum usersAluminium / Galvanised
Occasional maintenance use
242mm
40mm
SWL 450Kg
250mm
100mm60o
For any technical queries please call our adviceline on 0845 241 9102
Swing gates are available to be fitted on one of both sides of the step over to prevent unauthorized access. The gates are fitted with a slam plate. There is a facility to fit a padlock if required. It is possible to have the gates automated and to interface with a
Step Overs can be manufactured and supplied in galvanized steel or aluminium. Traditionally galvanized steel has been specified but aluminium step overs are now also used extensively. Both types comply with current legislation. Galvanized ladders are more cost effective to produce but due to the weight are more difficult to deliver to site and install.
PAYLOAD STAIRS - STEPOVERS
security or fire alarm if required. The step overs can be assembled with only 1 flight of stairs if access is only required from a lower level to a higher level.
Both types of step overs are supplied in modular components to assist with manual handling issues on site. On larger ladders it will be necessary to have suitable lifting equipment in the form of a crane or MEWP to assemble and install on site.
Hinged gate Single flight and platform Double flight and platform
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD STAIRS - STEPOVERS
Yield 275 N/mm² C 0.15 – 0.26; Si < 0.35; Mn < 1.5; P < 0.035; S < 0.040; Mo 0.4 – 0.6.
Young’s Modulus of Elasticity 200 x 103 MPa at 20 °C
Density 7.87 g/cm3 at 20 °C
Coefficient of Thermal Expansion Low-Carbon/HSLAS: 12.4 μm/m/°C in 20 °C to 100 °C range I-F Steel: 12.9 μm/m/°C in 20 °C to 100 °C range
Thermal Conductivity Low-Carbon/HSLAS: 89 W/m°C at 20°C I-F Steel: 93 W/m°C at 20°C
Specific Heat 481 J/kg/°C in 50 °C to 100 °C range
Electrical Resistivity 0.142 μΩ•m at 20 °C
Galvanised steel profile
MATERIAL SPECIFICATION:
Aluminium profileAluminium extrusion 0.50 - 0.75 Si, Max 0.35, Fe 0.40 - 0.70 MgTensile strength PSI 23,000 Yield strength PSI 15,000
Natural rubber base CIS14 Polyisoprene - Optional
Durometer (Shore A) 30-90Specific Gravity (Polymer) 0.92Tensile Strength Max-psi (Mpa) 3500 (24.1)Low Temperature Brittle Point (C/F) -58/-70Tear Strength EFlame Retardent Properties PSealing Characteristics P
Aluminium
Galvanised
Aluminium Galvanised
Rubber base
061
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD STAIRS - STEPOVERS
Typical connection loads
Vertical shear
Uniform load 100mm2
Tension
Maximum SWL
3Kn 0.5Kn
150Kg 450Kg
Note: For guidelines only to be checked by Chief Engineer.
OPERATING AND DESIGN STANDARDS:Eurocodes are designated by EN British standards are designated by BS
• BS4211:2005+A1:2008• BS EN 12020-1 and 2 :2008 Aluminium and
Aluminium alloy extrusions• BS EN 755:2008 series Extruded profiles• BS EN 754: 2008 series Tolerances on dimensions
extruded profiles• BS 1154:2003- Physical and compositional
properties for natural black rubber• ISO 9001:2008• ISO 14001:2004• BS OHSAS 18001:2007• Work at height regulations 2005 (Ref.7)
✔
BS ENISO
Standards
• Work at height (amendment) Regulations2007 (Ref.8) WAHR
• Provision and use of work equipment regulations1998 PUWER 98 (Ref. 5)
• Management of health and safety at workregulations 1999 MHSWR (Ref.2)
• The Building Regulations 2010 part K.
061
The company operates to the following standards
For any technical queries please call our adviceline on 0845 241 9102
Maintenance to be in accordance with SIMS standards. (details available on request)
Maintenance to be carried out at time of yearly inspection.
Contact Sayfa Systems to arrange system maintenance.
TRAINING REQUIREMENTS:All personnel who use the Aviator system should have attended a NASLOT (National Access and Safety Line Operator Training) course. Courses are available from Sayfa Systems UK Ltd.
INSPECTION/MAINTENANCE/TRAINING
INSPECTION ROUTINE:All systems to be inspected at least every 12 months from date of installation.
In harsh environments all systems to be inspected at least every 3 months.
Inspections must be carried out by approved Aviator engineers.
Inspections must be approved to SIMS (Safety Inspection and Maintenance Service) standards.
All inspections to be carried out to EN795:2012 and BS 7883:2005 and WAHSA (inspection of eyebolts) requirements for safety line and anchor points.
All inspections to be carried out to EN364 requirements for personal protective equipment.
Contact Sayfa Systems to arrange inspections.
MAINTENANCE SCHEDULE:All maintenance to be carried out by approved Aviator engineers.
Maintenance to be in accordance with Sayfa Systems UK (manufacturer) guidelines and recommendations.
In harsh environments all systems to be inspected at least every 3 months.
12 Months
From date of installation
NASLOT
CERTIFIED
3Months
in harsh environments
d
Sa
yfa
SyStem
S
Ce
R t I f I C a
te
NASLOT
CERTIFIED
Certificate
PASS ✔
12 Months
From date of installation
3Months
in harsh environments
d
PAYLOAD STAIRS - STEPOVERS
061
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD STAIRS - STEPOVERS
GALVANISEDSTEEL FINISH
800
242
LENGTH OF PLATFORM500mm, 1000mm,1500mm, 2000mm
VARIABLE TO SUIT CUSTOMERS REQUIREMENTS
800
LENGTH OF WALKWAY TO SUIT PLATFORM LENGTH
20
STAIR TREAD ST800 STRINGER & HANDRAIL SH1000
PLATFORM MESH PM 1000PLATFORM & HANDRAIL PH1000
TO SUITNUMBER OF TREADS
COMPONENT PART DETAILS:Stair tread ST800 Stringer and handrail 1.0M SH1000
Platform and handrail PH1000 Platform mesh PM1000
GALVANISEDSTEEL FINISH
800
242
LENGTH OF PLATFORM500mm, 1000mm,1500mm, 2000mm
VARIABLE TO SUIT CUSTOMERS REQUIREMENTS
800
LENGTH OF WALKWAY TO SUIT PLATFORM LENGTH
20
STAIR TREAD ST800 STRINGER & HANDRAIL SH1000
PLATFORM MESH PM 1000PLATFORM & HANDRAIL PH1000
TO SUITNUMBER OF TREADS
GALVANISEDSTEEL FINISH
800
242
LENGTH OF PLATFORM500mm, 1000mm,1500mm, 2000mm
VARIABLE TO SUIT CUSTOMERS REQUIREMENTS
800
LENGTH OF WALKWAY TO SUIT PLATFORM LENGTH
20
STAIR TREAD ST800 STRINGER & HANDRAIL SH1000
PLATFORM MESH PM 1000PLATFORM & HANDRAIL PH1000
TO SUITNUMBER OF TREADS
GALVANISEDSTEEL FINISH
800
242
LENGTH OF PLATFORM500mm, 1000mm,1500mm, 2000mm
VARIABLE TO SUIT CUSTOMERS REQUIREMENTS
800
LENGTH OF WALKWAY TO SUIT PLATFORM LENGTH
20
STAIR TREAD ST800 STRINGER & HANDRAIL SH1000
PLATFORM MESH PM 1000PLATFORM & HANDRAIL PH1000
TO SUITNUMBER OF TREADS
061
For any technical queries please call our adviceline on 0845 241 9102
COMPONENT PART DETAILS:Ladder base LB1000 Swing gate LSG800
Fixings M12 x 30 Access sign AS100
PAYLOAD STAIRS - STEPOVERS
100
LENGTH OF BASE 1000mm
NOUNAUTHORISED
ACCESS
750
800
SPRING LOADEDHINGES OPTIONAL
PADLOCK PLATE
LADER BASE LB 1000 SWING GATE LSG 800
ACCESS WARNING SIGN SWS 100FIXINGS M12 x 30
100
LENGTH OF BASE 1000mm
NOUNAUTHORISED
ACCESS
750
800
SPRING LOADEDHINGES OPTIONAL
PADLOCK PLATE
LADER BASE LB 1000 SWING GATE LSG 800
ACCESS WARNING SIGN SWS 100FIXINGS M12 x 30
100
LENGTH OF BASE 1000mm
NOUNAUTHORISED
ACCESS
750
800
SPRING LOADEDHINGES OPTIONAL
PADLOCK PLATE
LADER BASE LB 1000 SWING GATE LSG 800
ACCESS WARNING SIGN SWS 100FIXINGS M12 x 30
100
LENGTH OF BASE 1000mm
NOUNAUTHORISED
ACCESS
750
800
SPRING LOADEDHINGES OPTIONAL
PADLOCK PLATE
LADER BASE LB 1000 SWING GATE LSG 800
ACCESS WARNING SIGN SWS 100FIXINGS M12 x 30
061
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD STAIRS - STEPOVERS
FIXING DETAILS: LD400L18 Free standing stairs
Two flight - BIM No: SpecEquip_RfSftySymFreStdStpOvrDbl_SayfaSystems_LD400L182_M3_G2
1100
1000
800
250
100
500mm, 1000mm, 1500mm, 2000mmVARIABLE TO SUIT CUSTOMER REQUIREMENTS
HEIGHT TO UNDERSIDE OF PLATFORM500mm, 750mm, 1000mm,1250mm, 1500mm
VARIABLE TO SUIT CUSTOMERS REQUIREMENTS
20 x 20 x 1.5
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™STEP OVERS2 FLIGHTS &PLATFORM
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
061
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: LD400L17 Free standing stairs BIM No: SpecEquip_RfSftySymFreStdStpOvrSgl_SayfaSystems_LD400L181_M3_G2
PAYLOAD STAIRS - STEPOVERS
1100
500mm, 1000mm, 1500mm, 2000mmVARIABLE TO SUIT CUSTOMER REQUIREMENTS
250
HEIGHT TO UNDERSIDE OF PLATFORM500mm, 750mm, 1000mm,1250mm, 1500mm
VARIABLE TO SUIT CUSTOMERS REQUIREMENTS
1100
1000
800
250
100
20 x 20 x 1.5
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™STEP OVERS1 FLIGHTS &PLATFORM
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
061
For any technical queries please call our adviceline on 0845 241 9102
DATE: 28/10/2014PRODUCT DATA SHEET REPORT NO: 062
PRODUCT CODE: LD400L19
COMPANION WAY LADDERS
062
For any technical queries please call our adviceline on 0845 241 9102
PRODUCT DESCRIPTION:Companion way ladders consist of a single flight of narrow stairs between two levels. They are generally easier and safer to use than a vertical ladder. These types of ladders are usually provided when space is at a premium and the provision of a standard stair is not an option. The companion way ladder systems are 800mm wide and supplied in heights up to 3m
Payload companion way ladders are manufactured as a single unit to ensure speed of installation. The angler of the ladder is set between 60-75 degrees. The stair treads are 242mm wide and the rise is 225mm - 255mm. The rise is consistent throughout the stair starting from the top step. The lower step
PAYLOAD STAIRS - COMPANION WAY LADDERS
maximum. They are designed to be fixed to the floor and wall and may require additional upright supports. The companion way ladders are designed as a permanent means of access and usually left in position throughout the duration of the access requirements. The system is supplied with handrail on both sides for added safety.
to ground may vary depending on the ladder length. The steps have a non-slip nosing on the leading edge. Care should be taken in extreme weather as some surfaces may become slippery. The stairs nosings can be colour coded if required for an additional cost.
3.0mMaximum
800mm
242mm
225mm -255mm
Max Varies
Top of rung to top of rung
60-75o
062
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD STAIRS - COMPANION WAY LADDERS
All fixings are capable of supporting a shear load of 3Kn force and a tension force of 0,5Kn. The platform and stairs can support a weight of 150Kg spread over a 100mm area. The ultimate SWL is 450kg on each complete stair set. No more than 2 users are allowed
Swing gates are available to be fitted on one of both sides of the step over to prevent unauthorized access. The gates will open onto the platforms and not the ladder. The gates are fitted with a slam plate.
on each stair at any time. The companion way ladders are designed for occasional maintenance use. Should high usage or fire access use be required our designers can advise on specific designs.
Maximum users
SWL 450Kg
There is a facility to fit a padlock if required. A platform can be fitted at the top of the ladder if required. Platform cantilever should not extend more than 600mm.
Occasional access use
600mm
1110mm
062
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD STAIRS - COMPANION WAY LADDERS
Handrails on the ladders are always fitted on both sides. A minimum clear width of 600mm is maintained between the handrails. Stanchions supporting the handrails are positioned at right angles to the stringers. The top of the handrail will
Companion way ladders can be manufactured and supplied in galvanized steel or aluminium. Traditionally galvanized steel has been specified but aluminium step overs are now also used extensively. Both types comply with current legislation. Galvanized ladders are more cost effective to produce but due to the weight are more difficult to
be at least 250mm above the top of the stringer. The handrails are continuous throughout the entire flight of the stairs. A minimum clear space of at least 1,2m is required measured at right angles to the stringer.
deliver to site and install. On larger ladders it will be necessary to have suitable lifting equipment in the form of a crane or MEWP to assemble and install on site. Careful planning is necessary to ensure that the ladders are fitted during the construction phase while access and lifting equipment is still available.
Clear space
1.2m250mm
90o
062
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD STAIRS - COMPANION WAY LADDERS
Yield 275 N/mm² C 0.15 – 0.26; Si < 0.35; Mn < 1.5; P < 0.035; S < 0.040; Mo 0.4 – 0.6.
Young’s Modulus of Elasticity 200 x 103 MPa at 20 °C
Density 7.87 g/cm3 at 20 °C
Coefficient of Thermal Expansion Low-Carbon/HSLAS: 12.4 μm/m/°C in 20 °C to 100 °C range I-F Steel: 12.9 μm/m/°C in 20 °C to 100 °C range
Thermal Conductivity Low-Carbon/HSLAS: 89 W/m°C at 20°C I-F Steel: 93 W/m°C at 20°C
Specific Heat 481 J/kg/°C in 50 °C to 100 °C range
Electrical Resistivity 0.142 μΩ•m at 20 °C
Galvanised steel profile
MATERIAL SPECIFICATION:
Aluminium profileAluminium extrusion 0.50 - 0.75 Si, Max 0.35, Fe 0.40 - 0.70 MgTensile strength PSI 23,000 Yield strength PSI 15,000
Natural rubber base CIS14 Polyisoprene - Optional
Durometer (Shore A) 30-90Specific Gravity (Polymer) 0.92Tensile Strength Max-psi (Mpa) 3500 (24.1)Low Temperature Brittle Point (C/F) -58/-70Tear Strength EFlame Retardent Properties PSealing Characteristics P
Aluminium/Galvanised stairs
Aluminium/ Galvanised handrail
Aluminium/ Galvanised floor plate
Aluminium/Galvanised stringer
062
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD STAIRS - COMPANION WAY LADDERS
Typical connection loads
Vertical shear
Uniform load 100mm2
Tension
Maximum SWL
3Kn 0.5Kn
150Kg 450Kg
Note: For guidelines only to be checked by Chief Engineer.
OPERATING AND DESIGN STANDARDS:Eurocodes are designated by EN British standards are designated by BS
• BS4211:2005+A1:2008• BS EN 12020-1 and 2 :2008 Aluminium and
Aluminium alloy extrusions• BS EN 755:2008 series Extruded profiles• BS EN 754: 2008 series Tolerances on dimensions
extruded profiles• BS 1154:2003- Physical and compositional
properties for natural black rubber• ISO 9001:2008• ISO 14001:2004• BS OHSAS 18001:2007• Work at height regulations 2005 (Ref.7)
✔
BS ENISO
Standards
• Work at height (amendment) Regulations2007 (Ref.8) WAHR
• Provision and use of work equipment regulations1998 PUWER 98 (Ref. 5)
• Management of health and safety at workregulations 1999 MHSWR (Ref.2)
• The Building Regulations 2010 part K.
062
The company operates to the following standards
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD STAIRS - COMPANION WAY LADDERS
Maintenance to be in accordance with SIMS standards. (details available on request)
Maintenance to be carried out at time of yearly inspection.
Contact Sayfa Systems to arrange system maintenance.
TRAINING REQUIREMENTS:All personnel who use the Aviator system should have attended a NASLOT (National Access and Safety Line Operator Training) course. Courses are available from Sayfa Systems UK Ltd.
INSPECTION/MAINTENANCE/TRAINING
INSPECTION ROUTINE:All systems to be inspected at least every 12 months from date of installation.
In harsh environments all systems to be inspected at least every 3 months.
Inspections must be carried out by approved Aviator engineers.
Inspections must be approved to SIMS (Safety Inspection and Maintenance Service) standards.
All inspections to be carried out to EN795:2012 and BS 7883:2005 and WAHSA (inspection of eyebolts) requirements for safety line and anchor points.
All inspections to be carried out to EN364 requirements for personal protective equipment.
Contact Sayfa Systems to arrange inspections.
MAINTENANCE SCHEDULE:All maintenance to be carried out by approved Aviator engineers.
Maintenance to be in accordance with Sayfa Systems UK (manufacturer) guidelines and recommendations.
In harsh environments all systems to be inspected at least every 3 months.
12 Months
From date of installation
NASLOT
CERTIFIED
3Months
in harsh environments
d
Sa
yfa
SyStem
S
Ce
R t I f I C a
te
NASLOT
CERTIFIED
Certificate
PASS ✔
12 Months
From date of installation
3Months
in harsh environments
d
062
For any technical queries please call our adviceline on 0845 241 9102
COMPONENT PART DETAILS:Ladder LD400L21 60o - BIM No: SpecEquip_RfSftySymCpnLdr_SayfaSystems_LD400L2060_M3_G2
75o - BIM No: SpecEquip_RfSftySymCpnLdr_SayfaSystems_LD400L2075_M3_G2 Platform LD400PL
Swing gate LSG800 Support leg SL100
PAYLOAD STAIRS - COMPANION WAY LADDERS
60011
00
1100
250
250
750
800
SPRING LOADEDHINGES OPTIONAL
PADLOCK PLATE
600
1100
LD 400 L19 LADDER PLATFORM 600mm LD400PL
SUPPORT LEG100mm x 100mm 3mm
SWING GATE 0.8m LSG 800
TO SUITNUMBER OF TREADS
600
1100
1100
250
250
750
800
SPRING LOADEDHINGES OPTIONAL
PADLOCK PLATE
600
1100
LD 400 L19 LADDER PLATFORM 600mm LD400PL
SUPPORT LEG100mm x 100mm 3mm
SWING GATE 0.8m LSG 800
TO SUITNUMBER OF TREADS
600
1100
1100
250
250
750
800
SPRING LOADEDHINGES OPTIONAL
PADLOCK PLATE
600
1100
LD 400 L19 LADDER PLATFORM 600mm LD400PL
SUPPORT LEG100mm x 100mm 3mm
SWING GATE 0.8m LSG 800
TO SUITNUMBER OF TREADS
600
1100
1100
250
250
750
800
SPRING LOADEDHINGES OPTIONAL
PADLOCK PLATE
600
1100
LD 400 L19 LADDER PLATFORM 600mm LD400PL
SUPPORT LEG100mm x 100mm 3mm
SWING GATE 0.8m LSG 800
TO SUITNUMBER OF TREADS
062
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD STAIRS - COMPANION WAY LADDERS
FIXING DETAILS: LD400L21 Fixed to brick/block wall
M10 RESINANCHORSET 100mm INCONCRETEMINIMUM4no FIXINGSREQUIRED
3m M
AX
IMU
M
1100
600
250
250
1100
60° - 75°
NON PENETRATINGRUBBER BASE CAN BESUBSTITUTED FOR FIXINGPLATE IF REQUIRED
WIDTH OF STAIRS 800mmBETWEEN STRINGERS
Ø42
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™COMPANION WAYLADDERFIXED TO BLOCK WALL
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
062
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD STAIRS - COMPANION WAY LADDERS
FIXING DETAILS: LD400L21 Fixed to brick/block wall with platform 60o - BIM No: SpecEquip_RfSftySymCpnLdrPltfm_SayfaSystems_LD400L2060LDNG_M3_G2
75o - BIM No: SpecEquip_RfSftySymCpnLdrPltfm_SayfaSystems_LD400L2075LDNG_M3_G2
M10 RESINANCHORSET 100mm INCONCRETEMINIMUM4no FIXINGSREQUIRED
3m M
AX
IMU
M
1100
600
250
250
60° - 75°
NON PENETRATINGRUBBER BASE CAN BESUBSTITUTED FOR FIXINGPLATE IF REQUIRED
WIDTH OF STAIRS 800mmBETWEEN STRINGERS
Ø42
600
M10 RESINANCHORSET 100mm INCONCRETEMINIMUM4no FIXINGSREQUIRED
OPTIONAL SUPPORT LEG100mm x 100mm x 3mm
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™COMPANION WAYLADDERFIXED TO BLOCK WALLWITH PLATFORM
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
062
For any technical queries please call our adviceline on 0845 241 9102
DATE: 28/10/2014PRODUCT DATA SHEET REPORT NO: 063
PRODUCT CODE: RW400
RAISED WALKWAY
063
For any technical queries please call our adviceline on 0845 241 9102
PRODUCT DESCRIPTION:The Payload raised walkway systems is designed to facilitate safe access on a designated access pathway, over pipework, roof penetrations, parapet walls and roof plant. The walkway is 800mm wide and supplied in 1m modules. The maximum height of the raised walkway system is 500mm. The raised walkway is designed to be free standing on rubber
Payload raised walkway is designed as a modular system to ensure ease of installation. The walkway mesh easily bolts between the sides and the rubber base feet and completes the product. If the site has suitable lifting equipment it is possible to fully
base plates which ensures that no roof or wall penetrations are required. The raised walkway is designed as a permanent means of access and usually left in position throughout the duration of the access requirements. The raised walkway is supplied with handrail on both sides for added safety.
assemble the unit before delivering to site and then lift safely into position. The rubber base feet have an adjustment facility to ensure the stairs can remain level on surfaces that are angled at up to 10 degrees.
PAYLOAD STAIRS - RAISED WALKWAY
100mm - 500mm
1.0m 800mm
Side and handrail Walkway mesh Rubber base
063
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD STAIRS - RAISED WALKWAY
The walkway mesh is constructed from rectangular welded mesh. The mesh is non slip under normal working conditions. Care should be taken in extreme weather as some surfaces may become slippery. All fixings are capable of supporting a shear load of 3Kn force and a tension force of 0,5Kn. The platform and stairs can support a weight of 150Kg spread
Swing gates are available to be fitted on one of both sides of the raised walkway to prevent unauthorized access. The gates are fitted with a slam plate. There is a facility to fit a padlock if required. It is possible to
Raised walkway can be manufactured and supplied in galvanized steel or aluminium. Traditionally galvanized steel has been specified but aluminium step overs are now also used extensively. Both types comply with current legislation. Galvanized raised
over a 100mm area. The ultimate SWL is 450kg on each complete walkway set. No more than 2 users are allowed on each walkway module at any time. The raised walkway is designed for occasional maintenance use. Should high usage or fire access use be required our designers can advise on specific designs.
have the gates automated and to interface with a security or fire alarm if required. Corner units are available should the walkway be required to turn through a 90 degree angle.
walkway units are more cost effective to produce but due to the weight are more difficult to deliver to site and install. Both types of raised walkway are supplied in modular components to assist with manual handling issues on site.
Hinged gate
Occasional maintenance use
Maximum users per unit
SWL 450Kg
Aluminium/Galvanised
Corner unit
Unit2
Unit3
Unit1
063
For any technical queries please call our adviceline on 0845 241 9102
Yield 275 N/mm² C 0.15 – 0.26; Si < 0.35; Mn < 1.5; P < 0.035; S < 0.040; Mo 0.4 – 0.6.
Young’s Modulus of Elasticity 200 x 103 MPa at 20 °C
Density 7.87 g/cm3 at 20 °C
Coefficient of Thermal Expansion Low-Carbon/HSLAS: 12.4 μm/m/°C in 20 °C to 100 °C range I-F Steel: 12.9 μm/m/°C in 20 °C to 100 °C range
Thermal Conductivity Low-Carbon/HSLAS: 89 W/m°C at 20°C I-F Steel: 93 W/m°C at 20°C
Specific Heat 481 J/kg/°C in 50 °C to 100 °C range
Electrical Resistivity 0.142 μΩ•m at 20 °C
Galvanised steel profile
MATERIAL SPECIFICATION:
Aluminium profileAluminium extrusion 0.50 - 0.75 Si, Max 0.35, Fe 0.40 - 0.70 MgTensile strength PSI 23,000 Yield strength PSI 15,000
Natural rubber base CIS14 Polyisoprene - Optional
Durometer (Shore A) 30-90Specific Gravity (Polymer) 0.92Tensile Strength Max-psi (Mpa) 3500 (24.1)Low Temperature Brittle Point (C/F) -58/-70Tear Strength EFlame Retardent Properties PSealing Characteristics P
PAYLOAD STAIRS - RAISED WALKWAY
Aluminium
Rubber base
Galvanised
063
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD STAIRS - RAISED WALKWAY
Typical connection loads
Vertical shear
Uniform load 100mm2
Tension
Maximum SWL
3Kn 0.5Kn
150Kg 450Kg
Note: For guidelines only to be checked by Chief Engineer.
OPERATING AND DESIGN STANDARDS:Eurocodes are designated by EN British standards are designated by BS
• BS4211:2005+A1:2008• BS EN 12020-1 and 2 :2008 Aluminium and
Aluminium alloy extrusions• BS EN 755:2008 series Extruded profiles• BS EN 754: 2008 series Tolerances on dimensions
extruded profiles• BS 1154:2003- Physical and compositional
properties for natural black rubber• ISO 9001:2008• ISO 14001:2004• BS OHSAS 18001:2007• Work at height regulations 2005 (Ref.7)
✔
BS ENISO
Standards
• Work at height (amendment) Regulations2007 (Ref.8) WAHR
• Provision and use of work equipment regulations1998 PUWER 98 (Ref. 5)
• Management of health and safety at workregulations 1999 MHSWR (Ref.2)
• The Building Regulations 2010 part K.
063
The company operates to the following standards
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD STAIRS - RAISED WALKWAY
Maintenance to be in accordance with SIMS standards. (details available on request)
Maintenance to be carried out at time of yearly inspection.
Contact Sayfa Systems to arrange system maintenance.
TRAINING REQUIREMENTS:All personnel who use the Aviator system should have attended a NASLOT (National Access and Safety Line Operator Training) course. Courses are available from Sayfa Systems UK Ltd.
INSPECTION/MAINTENANCE/TRAINING
INSPECTION ROUTINE:All systems to be inspected at least every 12 months from date of installation.
In harsh environments all systems to be inspected at least every 3 months.
Inspections must be carried out by approved Aviator engineers.
Inspections must be approved to SIMS (Safety Inspection and Maintenance Service) standards.
All inspections to be carried out to EN795:2012 and BS 7883:2005 and WAHSA (inspection of eyebolts) requirements for safety line and anchor points.
All inspections to be carried out to EN364 requirements for personal protective equipment.
Contact Sayfa Systems to arrange inspections.
MAINTENANCE SCHEDULE:All maintenance to be carried out by approved Aviator engineers.
Maintenance to be in accordance with Sayfa Systems UK (manufacturer) guidelines and recommendations.
In harsh environments all systems to be inspected at least every 3 months.
12 Months
From date of installation
NASLOT
CERTIFIED
3Months
in harsh environments
d
Sa
yfa
SyStem
S
Ce
R t I f I C a
te
NASLOT
CERTIFIED
Certificate
PASS ✔
12 Months
From date of installation
3Months
in harsh environments
d
063
For any technical queries please call our adviceline on 0845 241 9102
COMPONENT PART DETAILS:Straight side and handrail PRW1000
Corner side and handrail PRC1000
Ladder base LB100 Platform mesh PM1000
PAYLOAD STAIRS - RAISED WALKWAY
1100
1000
125
20
100
LENGTH OF BASE 100mm
800
LENGTH OF WALKWAY TO SUIT PLATFORM LENGTH
20
1100
800
125
20
STRAIGHT SECTION & HANDRAILPRW 1000
CORNER SECTION & HANDRAILPRC 1000
PLATFORM MESH PM 1000LADDER BASE LBF 500
1100
1000
125
2010
0
LENGTH OF BASE 100mm
800
LENGTH OF WALKWAY TO SUIT PLATFORM LENGTH
20
1100
800
125
20
STRAIGHT SECTION & HANDRAILPRW 1000
CORNER SECTION & HANDRAILPRC 1000
PLATFORM MESH PM 1000LADDER BASE LBF 500
1100
1000
125
20
100
LENGTH OF BASE 100mm
800
LENGTH OF WALKWAY TO SUIT PLATFORM LENGTH
20
1100
800
125
20
STRAIGHT SECTION & HANDRAILPRW 1000
CORNER SECTION & HANDRAILPRC 1000
PLATFORM MESH PM 1000LADDER BASE LBF 500
1100
1000
125
20
100
LENGTH OF BASE 100mm
800
LENGTH OF WALKWAY TO SUIT PLATFORM LENGTH
20
1100
800
125
20
STRAIGHT SECTION & HANDRAILPRW 1000
CORNER SECTION & HANDRAILPRC 1000
PLATFORM MESH PM 1000LADDER BASE LBF 500
063
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD STAIRS - RAISED WALKWAY
FIXING DETAILS: LD400L19 Straight section BIM No: SpecEquip_RaiWlkWayStrt_SayfaSystems_LD400L19STRT_M3_G2
1100
1000
800
1000
125
20
VARIABLE HEIGHT 100mm - 500mm
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™RAISED WALKWAYSTRAIGHT SECTIONDIMENSIONS
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
063
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD STAIRS - RAISED WALKWAY
FIXING DETAILS: LD400L19 Corner section BIM No: SpecEquip_RaiWlkWayCnr_SayfaSystems_LD400L19CNR_M3_G2
1100
80012
5
20
VARIABLE HEIGHT 100mm - 500mm
800
800
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™RAISED WALKWAYCORNER SECTIONDIMENSIONS
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
063
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD STAIRS - RAISED WALKWAY
FIXING DETAILS: LD400L19 System layout
80010001000
800
1000
1000
800 ACCESS WIDTH
800
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™RAISED WALKWAYMODULARLAYOUT DETAILS
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
063
For any technical queries please call our adviceline on 0845 241 9102
DATE: 28/10/2014PRODUCT DATA SHEET REPORT NO: 071
PRODUCT CODE: WWM610GRP
GRP WALKWAY (GLASS REINFORCED PLASTIC) - ONTRACK
071
For any technical queries please call our adviceline on 0845 241 9102
PRODUCT DESCRIPTION:Glass reinforced walkway systems are designed to facilitate safe access and provide a designated access walkway on a roof. The walkway is 610mm or 810mmwide and supplied in 2.4m sections and is 25mm thick. The mesh size is normally 25mm square but can vary. The walkway is grey in colour. The walkway is designed to be laid on top of a completed roof system. It is a permanent means
PAYLOAD WALKWAY - GRP
of access and usually left in position throughout the duration of the access requirements. Glass reinforced walkway systems are fire resistant and extremely resistant to most industrial chemicals. The walkway provides excellent safety standards with minimal maintenance. It is non-conductive, non-magnetic and is ideal for use in harsh or consistently wet environments.
2.4m
810mm
610mm 25mm
25mm
071
For any technical queries please call our adviceline on 0845 241 9102
The walkway is supplied with fixing clips and joiners to suit most types of roof profile. There are specialist clips for standing seam roofs and secret fix roofs which have been tested and approved for use. For steel composite panels the clip can be riveted to the deck with the Sayfa bulb type rivets. The walkway is
PAYLOAD WALKWAY - GRP
not recommended for use on a PVC membrane roof and the Sayfa PVC walkway should be installed in these situations. For bitumen or hot melt rubber the walkway can be laid on top and the fixing clip fixed down with a suitable mastic or similar.
Standing seam
Composite steel Bitumen / Hot melt rubber
Secret fix
071
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GRP
GRP walkway is suitable for use on its own on a roof pitch of up to 10 degrees. Between 10 degrees and 20 degrees the walkway should be used with a handrail fixed to at least 1 side. The handrail is normally positioned on the lower edge of the walkway. Between 20 degrees to 45 degrees the walkway must be fitted with levelling plates, steps and handrail on
GRP walkway is extremely hard wearing and has exceptional strength to weight ratio. The 25mm thick walkway can span a 500mm gap without additional supports. This makes it an extremely cost effective system for most prefabricated roof sections that have an up stand. If there are gaps wider than 500mm Than support bars should be fitted.. The mesh is non slip under normal working conditions. Care should be taken in extreme weather as some surfaces may become slippery. All fixings (except for mastic joints) are capable of supporting a shear load of 1.5Kn
both sides. If handrail is to be fitted both sides it is recommended to use the 810mm wide panel to ensure the access width between the panels is no less than 600mm. It is not recommended to fit the walkway on any roofs over 45 degrees and a fixed access ladder should be considered in these situations.
force and a tension force of 0,5Kn. The walkway can support a weight of 150Kg spread over a 100mm area on the unsupported sections with a maximum deflection of 25mm. The ultimate SWL is 300kg on each complete walkway section. No more than 2 users are allowed on each walkway system at any time. The walkway is designed for occasional maintenance use only. Should high usage or fire access use be required our designers can advise on specific designs.
10o
10-20o
20-45o
Occasional maintenance use
Maximum users per unit
SWL 300Kg
1.0Kn0.5Kn
0.5m
071
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GRP
GRP walkway is supplied with joiners or joining strip. Both types are suitable and conform to the required standards. It is possible at time of manufacture to provide different colours to grey but large minimum quantities and additional charges will apply. The slip resistance of the GRP flooring is determined by
The GRP walkway can be integrated and used together with the Payload step overs and raised walkway if required. Involving our design team early will ensure that full consideration is given to the operator safety both during construction and for
a specific British standard test BS 4592. This slip test determines the friction of the walkway for wet areas and is conducted using a steady stream of water. GRP outperforms both metal and aluminium mesh flooring systems in this test.
long term maintenance. It is recommended to use the walkway together with additional safety protection such as Payload handrail or The Aviator safety line system.
1.10
1.00
0.90
0.80
0.70
0.60
0.50
0.40
0.30
0.20
1.04
On-track
CoF
(Co-
effic
ient
of f
rict
ion)
Metal grating Chequer plate
0.44
0.31
071
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GRP
MATERIAL SPECIFICATION:
GRP mesh and walkway joinerPolyester resin 20%, chopped strand laminate 10%, Woven rovings laminate glass 45%, Satin weave cloth glass laminate 25% ( percentages are approximate)Specific gravity 1.28Tensile Strength 55MN/M2Compression strength 140MN/m2Thermal conductivity 0.3W/moCVoltage breakdown 22KV/mm
Aluminium roofing clampsAluminium extrusion 0.50 - 0.75 Si, Max 0.35, Fe 0.40 - 0.70 MgTensile strength PSI 20,000 Yield strength PSI 11,000
Stainless steel walkway clipsGrade 304 (UNS S30400)Fe, <0.08% C, 17.5-20% Cr, 8-11% Ni, <2% Mn, <1% Si, <0.045% P, <0.03% Stainless Steel
Stainless steel
GRP
Aluminium
071
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GRP
Typical connection loads (Maximum cantilever from substrate 75mm)
Uniform load 100mm2
Slip resistance
Tension
Maximum SWL
1.5Kn 0.5Kn
1.04CoF 300Kg
Note: For guidelines only to be checked by Chief Engineer.
OPERATING AND DESIGN STANDARDS:Eurocodes are designated by EN British standards are designated by BS
• BS EN 516:2006 Class 1-C Fabricated accessoriesfor roofing installations including walkways, treadsand steps.
• BS4211:2005+A1:2008• BS EN 12020-1 and 2 :2008 Aluminium and
Aluminium alloy extrusions• BS EN 755:2008 series Extruded profiles• BS EN 754: 2008 series Tolerances on dimensions
extruded profiles• BS 1154:2003- Physical and compositional
properties for natural black rubber• ISO 9001:2008• ISO 14001:2004
✔
BS ENISO
Standards
• BS OHSAS 18001:2007• Work at height regulations 2005 (Ref.7)• Work at height (amendment) Regulations
2007 (Ref.8) WAHR• Provision and use of work equipment regulations
1998 PUWER 98 (Ref. 5)• Management of health and safety at work
071
The company operates to the following standards
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GRP
Maintenance to be in accordance with SIMS standards. (details available on request)
Maintenance to be carried out at time of yearly inspection.
Contact Sayfa Systems to arrange system maintenance.
TRAINING REQUIREMENTS:All personnel who use the Aviator system should have attended a NASLOT (National Access and Safety Line Operator Training) course. Courses are available from Sayfa Systems UK Ltd.
INSPECTION/MAINTENANCE/TRAINING
INSPECTION ROUTINE:All systems to be inspected at least every 12 months from date of installation.
In harsh environments all systems to be inspected at least every 3 months.
Inspections must be carried out by approved Aviator engineers.
Inspections must be approved to SIMS (Safety Inspection and Maintenance Service) standards.
All inspections to be carried out to EN795:2012 and BS 7883:2005 and WAHSA (inspection of eyebolts) requirements for safety line and anchor points.
All inspections to be carried out to EN364 requirements for personal protective equipment.
Contact Sayfa Systems to arrange inspections.
MAINTENANCE SCHEDULE:All maintenance to be carried out by approved Aviator engineers.
Maintenance to be in accordance with Sayfa Systems UK (manufacturer) guidelines and recommendations.
In harsh environments all systems to be inspected at least every 3 months.
12 Months
From date of installation
NASLOT
CERTIFIED
3Months
in harsh environments
d
Sa
yfa
SyStem
S
Ce
R t I f I C a
te
NASLOT
CERTIFIED
Certificate
PASS ✔
12 Months
From date of installation
3Months
in harsh environments
d
071
For any technical queries please call our adviceline on 0845 241 9102
COMPONENT PART DETAILS:Walkway mesh WWM610 BIM No: SpecEquip_GrpWlkWay_SayfaSystems_WWM610GRP_M3_G2
Prefabricated stair WWST545
Walkway clip WWFC510 Standing seam clamp WWFC515
PAYLOAD WALKWAY - GRP
2400STANDARD
WIDTHS 610mm25mm THICK32mm MESH
250
250
WALKWAY MESH WWM 610 PREFABRICATED STAIR WWST 545
STANDING SEAM CLAMP WWFC515WALKWAY CLIP WWFC 510
TO SUITANGLE OF ROOF
2400STANDARD
WIDTHS 610mm25mm THICK32mm MESH
250
250
WALKWAY MESH WWM 610 PREFABRICATED STAIR WWST 545
STANDING SEAM CLAMP WWFC515WALKWAY CLIP WWFC 510
TO SUITANGLE OF ROOF
2400STANDARD
WIDTHS 610mm25mm THICK32mm MESH
250
250
WALKWAY MESH WWM 610 PREFABRICATED STAIR WWST 545
STANDING SEAM CLAMP WWFC515WALKWAY CLIP WWFC 510
TO SUITANGLE OF ROOF
2400STANDARD
WIDTHS 610mm25mm THICK32mm MESH
250
250
WALKWAY MESH WWM 610 PREFABRICATED STAIR WWST 545
STANDING SEAM CLAMP WWFC515WALKWAY CLIP WWFC 510
TO SUITANGLE OF ROOF
071
For any technical queries please call our adviceline on 0845 241 9102
COMPONENT PART DETAILS:Secret fix clamp WWFC520
Angled roof bracket WWRB200
Fixed handrail base plate D42-132 Joining strip WWJS505
PAYLOAD WALKWAY - GRP
SECRET FIX CLAMP WWF C520 BRACKET WWJB 505
WALKWAY JOINING STRIP600mm WIDE
FIXED HANDRAIL BASE PLATED42 132
TO SUITANGLE OF ROOF
SECRET FIX CLAMP WWF C520 BRACKET WWJB 505
WALKWAY JOINING STRIP600mm WIDE
FIXED HANDRAIL BASE PLATED42 132
TO SUITANGLE OF ROOF
SECRET FIX CLAMP WWF C520 BRACKET WWJB 505
WALKWAY JOINING STRIP600mm WIDE
FIXED HANDRAIL BASE PLATED42 132
TO SUITANGLE OF ROOF
SECRET FIX CLAMP WWF C520 BRACKET WWJB 505
WALKWAY JOINING STRIP600mm WIDE
FIXED HANDRAIL BASE PLATED42 132
TO SUITANGLE OF ROOF
071
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GRP
FIXING DETAILS: Walkway fixed to steel deck roof
WALKWAYJOINER ORCLAMP
THIS FIXING DETAIL IS CORRECT FOR PEAK CENTRES UP TO500mm
GLASS REINFORCED PLASTICWALKWAYMESH SIZE 35mm²
WALKWAY25mm THICK
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GRP WALKWAY FIXEDTO STEEL DECK
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
SELF SEALINGROOFING SCREWTO SUIT ROOF DECK
WALKWAYFIXING CLIP
071
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GRP
FIXING DETAILS: Walkway fixed to steel deck roof with steel support
WALKWAYJOINER ORCLAMP
THIS FIXING DETAIL IS CORRECT FOR PEAK CENTRES OVER 500mm
GLASS REINFORCED PLASTICWALKWAYMESH SIZE 35mm²
WALKWAY25mm THICK
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GRP WALKWAY FIXEDTO STEEL DECKWITH SUPPORT STEEL
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
SELF SEALINGROOFING SCREWTO SUIT ROOF DECKTO BE FITTED BOTHSIDES EVERY 1.5m
WALKWAYFIXING CLIPTO BE FITTEDBOTH SIDESEVERY 1.5m
SUPPORT STEEL40mm HIGH
071
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GRP
FIXING DETAILS: Walkway fixed to steel deck roof with handrail
GLASS REINFORCED PLASTICWALKWAYMESH SIZE 35mm²
Ø42mm TUBE AND FITTINGS
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GRP WALKWAY FIXEDTO STEEL DECKWITH HANDRAIL
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
SELF SEALING ROOFING SCREW TO SUIT ROOF DECKTO BE FITTED BOTH SIDES EVERY 1.5m
WALKWAYFIXING CLIPTO BE FITTED BOTH SIDESEVERY 1.5M
SUPPORT STEEL40mm HIGH
HANDRAIL BASE PLATEMAXIMUM SPACING 2.25m CENTRES
071
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Raised walkway and stairs fixed to steel deck
3 MM L-BRACKET
STEEL SUPPORTTO SUIT ROOF ANGLE
WALKWAY FIXING CLIP
610 mm GRP WALKWAY
20° - 45°
20° - 45°
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GRP RAISED WALKWAY& STAIRS FIXED TOSTEEL DECK
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
ADJUSTABLE ALUMINUMSTEP FRAME WORK
GRP WALKWAY250mm WIDE
SELF SEALINGROOFING SCREWSTO SUIT ROOF DECK
SELF SEALINGROOFING SCREWSTO SUIT ROOF DECK
5mm PROFILED ROOF CLAMPTO SUIT ROOF ANGLE
PAYLOAD WALKWAY - GRP
071
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GRP
FIXING DETAILS: Walkway fixed to standing seam roof
2400
500
STANDARDWIDTHS 610mm
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GRP WALKWAY FIXEDTO STANDING SEAMROOF
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
WALKWAYJOINER OR CLAMP
WALKWAYFIXING CLIP
ALUMINUM ROOFSEAM CLAMP
MINIMUM4 FIXING CLAMPSPER WALKWAYSECTION
071
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GRP
FIXING DETAILS: Walkway fixed to standing seam roof with steel support
2400
STANDARDWIDTHS 610mm
1000
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GRP WALKWAY FIXEDTO STANDING SEAMROOF WITH SUPPORTSTEEL
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
WALKWAYJOINER OR CLAMP
WALKWAYFIXING CLIP
ALUMINUM ROOFSEAM CLAMP
MINIMUM4 FIXING CLAMPSPER WALKWAYSECTION
SUPPORT STEEL40mm HIGH
SUPPORT STEEL
SEAMS GREATERTHAN 500mm
071
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GRP
FIXING DETAILS: Walkway fixed to standing seam roof with handrail
GLASS REINFORCED PLASTICWALKWAYMESH SIZE 35mm²
Ø42mm TUBE AND FITTINGS
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GRP WALKWAY FIXEDTO STANDING SEAMWITH HANDRAIL
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
SELF SEALING ROOFING SCREW TO SUIT ROOF DECKTO BE FITTED BOTH SIDES EVERY 1.5m
WALKWAYFIXING CLIPTO BE FITTED BOTH SIDESEVERY 1.5M
SUPPORT STEEL40mm HIGH
HANDRAIL BASE PLATEMAXIMUM SPACING 2.25m CENTRES
071
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GRP
FIXING DETAILS: Raised walkway and stairs fixed to standing seam roof
3 MM L-BRACKET
STEEL SUPPORTTO SUIT ROOF ANGLE
WALKWAY FIXING CLIP
610 mm GRP WALKWAY
20° - 45°
20° - 45°
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GRP RAISED WALKWAY& STAIRS FIXED TOSTANDING SEAM
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
ADJUSTABLE ALUMINUMSTEP FRAME WORK
GRP WALKWAY250mm WIDE
ALUMINUMROOF SEAM CLAMP
ALUMINUMROOF SEAM CLAMP
5mm PROFILED ROOF CLAMPTO SUIT ROOF ANGLE
ROOF SEAM
ROOF SEAM
071
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GRP
FIXING DETAILS: Walkway fixed to secret fix roof
2400
500
STANDARDWIDTHS 610mm
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GRP WALKWAY FIXEDTO SECRET FIXROOF
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
WALKWAYJOINER OR CLAMP
WALKWAYFIXING CLIP
SECRET FIXCLAMP
MINIMUM4 FIXING CLAMPSPER WALKWAYSECTION
071
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Walkway fixed to secret fixed roof with steel support
2400
STANDARDWIDTHS 610mm
1000
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GRP WALKWAY FIXEDTO SECRET FIXROOF WITH SUPPORTSTEEL
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
WALKWAYJOINER OR CLAMP
WALKWAYFIXING CLIP
SECRET FIXCLAMP
MINIMUM4 FIXING CLAMPSPER WALKWAYSECTION
SUPPORT STEEL40mm HIGH
SUPPORT STEEL
SEAMS GREATERTHAN 500mm
PAYLOAD WALKWAY - GRP
071
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Walkway fixed to secret fixed roof with handrail
GLASS REINFORCED PLASTICWALKWAYMESH SIZE 35mm²
Ø42mm TUBE AND FITTINGS
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GRP WALKWAY FIXEDTO SECRET FIXWITH HANDRAIL
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
SELF SEALING ROOFING SCREW TO SUIT ROOF DECKTO BE FITTED BOTH SIDES EVERY 1.5m
WALKWAYFIXING CLIPTO BE FITTED BOTH SIDESEVERY 1.5M
SUPPORT STEEL40mm HIGH
HANDRAIL BASE PLATEMAXIMUM SPACING 2.25m CENTRES
SECRET FIX CLAMP
PAYLOAD WALKWAY - GRP
071
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Raised walkway and stairs fixed to secret fix roof
3 MM L-BRACKET
STEEL SUPPORTTO SUIT ROOF ANGLE
WALKWAY FIXING CLIP
610 mm GRP WALKWAY
20° - 45°
20° - 45°
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GRP RAISED WALKWAY& STAIRS FIXED TOSECRET FIX
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
ADJUSTABLE ALUMINUMSTEP FRAME WORK
GRP WALKWAY250mm WIDE
ALUMINUMSECRET FIX CLAMP
ALUMINUMSECRET FIX CLAMP
5mm PROFILED ROOF CLAMPTO SUIT ROOF ANGLE
SECRET FIXROOF SEAM
SECRET FIXROOF SEAM
PAYLOAD WALKWAY - GRP
071
For any technical queries please call our adviceline on 0845 241 9102
DATE: 28/10/2014PRODUCT DATA SHEET REPORT NO: 072
PRODUCT CODE: WWM1000GS
GALVANISED WALKWAY
072
For any technical queries please call our adviceline on 0845 241 9102
PRODUCT DESCRIPTION:Galvanised walkway systems are designed to facilitate safe access and provide a designated access walkway on a roof or building. The walkway is 1000mm wide, supplied in up to 6.0m sections and is 20mm thick. The mesh size is normally a rectangular mesh design but can vary. The walkway is supplied in steel which has been hot dipped
PAYLOAD WALKWAY - GALVANISED
galvanised and is extremely resistant to rust. The walkway is designed to be laid on top of a completed roof system or access framework. It is a permanent means of access and usually left in position throughout the duration of the access requirements. Galvanised walkway systems are heavy duty and strong. The walkway provides a robust and high usage system with low maintenance.
Up to 6.0m
810mm
610mm 20mm
20mm
072
For any technical queries please call our adviceline on 0845 241 9102
The walkway is supplied with fixing clips and joiners to suit most types of roof profile. There are specialist clips for standing seam roofs and secret fix roofs which have been tested and approved for use. Careful attention must be taken to provide a non-conductive break between two dissimilar materials. For steel composite panels the clip can be riveted
PAYLOAD WALKWAY - GALVANISED
to the deck with the Sayfa bulb type rivets. The walkway is not recommended for use on a PVC membrane roof and the Sayfa PVC walkway should be installed in these situations. For bitumen or hot melt rubber the walkway can be laid on top and the fixing clip fixed down with a suitable mastic or similar.
Standing seam
Composite steel Bitumen / Hot melt rubber
Secret fix
072
For any technical queries please call our adviceline on 0845 241 9102
Galvanised walkway is suitable for use on its own on a roof pitch of up to 10 degrees. Between 10 degrees and 20 degrees the walkway should be used with a handrail fixed to at least 1 side. The handrail is normally positioned on the lower edge of the walkway. Between 20 degrees to 45 degrees
Galvansied walkway is extremely hard wearing and has exceptional strength and load bearing capabilities. The 20mm thick walkway can span a 750mm gap without additional supports. This makes it the first choice for raised walkway and cantilever walkway systems. If there are gaps wider than 750mm support steels should be fitted. The mesh is non slip under normal working conditions. Care should be taken in extreme weather as some surfaces may become slippery. All fixings (except for mastic joints) are
the walkway must be fitted with levelling plates, steps and handrail on both sides. It is not recommended to fit the walkway on any roofs over 45 degrees and a fixed access ladder should be considered in these situations.
capable of supporting a shear load of 3Kn force and a tension force of 1.5Kn. The walkway can support a weight of 300Kg spread over a 100mm area on the unsupported sections with a maximum deflection of 25mm. The ultimate SWL is 500kg on each complete walkway section. Multiple users are allowed on each walkway system at any time. The walkway is designed for high maintenance use and is recommended to be used on fire access routes.
10o
10-20o
20-45o
High maintenance use
Maximum users per unit
SWL 500Kg
3.0Kn1.5Kn
750mm
PAYLOAD WALKWAY - GALVANISED
072
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GALVANISED
Galvanised walkway is supplied with joiners to ensure a seamless path. It is possible at time of manufacture to paint the walkway different colours but large minimum quantities and additional charges will apply. The slip resistance of the galvanised flooring is determined by a specific British standard
The walkway can be integrated and used together with the Payload step overs and raised walkway if required. Involving our design team early will ensure that full consideration is given to the operator safety both during construction and for long term maintenance. It is recommended to use the walkway together with additional safety protection such as
test BS 4592. This slip test determines the friction of the walkway for wet areas and is conducted using a steady stream of water. Galvanised is not as slip resistant as GRP walkway and should be substituted for GRP in extreme conditions.
Payload handrail or The Aviator safety line system. Care must be taken with galvanized steel to prevent the contact of 2 dissimilar metals once installed. Due to the weight of the mesh manual handling requirements must be discussed prior to installation. The use of lifting equipment is highly recommended.
1.10
1.00
0.90
0.80
0.70
0.60
0.50
0.40
0.30
0.20
1.04
On-track
CoF
(Co-
effic
ient
of f
rict
ion)
Metal grating Chequer plate
0.44
0.31
072
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GALVANISED
MATERIAL SPECIFICATION:
Aluminium walkway clampsAluminium extrusion 0.50 - 0.75 Si, Max 0.35, Fe 0.40 - 0.70 MgTensile strength PSI 20,000 Yield strength PSI 11,000
Galvanised steel
Galvanised steel
Aluminium
Yield 275 N/mm² C 0.15 – 0.26; Si < 0.35; Mn < 1.5; P < 0.035; S < 0.040; Mo 0.4 – 0.6.
Young’s Modulus of Elasticity 200 x 103 MPa at 20 °C
Density 7.87 g/cm3 at 20 °C
Coefficient of Thermal Expansion Low-Carbon/HSLAS: 12.4 μm/m/°C in 20 °C to 100 °C range I-F Steel: 12.9 μm/m/°C in 20 °C to 100 °C range
Thermal Conductivity Low-Carbon/HSLAS: 89 W/m°C at 20°C I-F Steel: 93 W/m°C at 20°C
Specific Heat 481 J/kg/°C in 50 °C to 100 °C range
Electrical Resistivity 0.142 μΩ•m at 20 °C
Galvanised steel mesh and brackets
072
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GALVANISED
OPERATING AND DESIGN STANDARDS:Eurocodes are designated by EN
British standards are designated by BS
• BS EN 516:2006 Class 1-C Fabricatedaccessories for roofing installations includingwalkways, treads and steps.
• BS4211:2005+A1:2008 Permanently fixedladders when used as steps or ladder treads.
• BS EN 12020-1 and 2 :2008 Aluminium andAluminium alloy extrusions for roof clamps
• BS EN 755:2008 series Extruded profiles• BS EN 754: 2008 series Tolerances on
dimensions extruded profiles• Plus standards from ACR M onwards
✔
BS ENISO
Standards
Typical connection loads (Maximum cantilever from substrate 75mm)
Uniform load 100mm2
Slip resistance
Tension
Maximum SWL
3.0Kn 1.5Kn
0.44CoF 500Kg
Note: For guidelines only to be checked by Chief Engineer.
072
The company operates to the following standards
• Work at height (amendment) Regulations2007 (Ref.8) WAHR
• Provision and use of work equipmentregulations 1998 PUWER 98 (Ref. 5)
• Management of health and safety at workregulations 1999 MHSWR (Ref.2)
• The Building Regulations 2010 part K.
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GALVANISED
Maintenance to be in accordance with SIMS standards. (details available on request)
Maintenance to be carried out at time of yearly inspection.
Contact Sayfa Systems to arrange system maintenance.
TRAINING REQUIREMENTS:All personnel who use the Aviator system should have attended a NASLOT (National Access and Safety Line Operator Training) course. Courses are available from Sayfa Systems UK Ltd.
INSPECTION/MAINTENANCE/TRAINING
INSPECTION ROUTINE:All systems to be inspected at least every 12 months from date of installation.
In harsh environments all systems to be inspected at least every 3 months.
Inspections must be carried out by approved Aviator engineers.
Inspections must be approved to SIMS (Safety Inspection and Maintenance Service) standards.
All inspections to be carried out to EN795:2012 and BS 7883:2005 and WAHSA (inspection of eyebolts) requirements for safety line and anchor points.
All inspections to be carried out to EN364 requirements for personal protective equipment.
Contact Sayfa Systems to arrange inspections.
MAINTENANCE SCHEDULE:All maintenance to be carried out by approved Aviator engineers.
Maintenance to be in accordance with Sayfa Systems UK (manufacturer) guidelines and recommendations.
In harsh environments all systems to be inspected at least every 3 months.
12 Months
From date of installation
NASLOT
CERTIFIED
3Months
in harsh environments
d
Sa
yfa
SyStem
S
Ce
R t I f I C a
te
NASLOT
CERTIFIED
Certificate
PASS ✔
12 Months
From date of installation
3Months
in harsh environments
d
072
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GALVANISED
072
COMPONENT PART DETAILS:Walkway mesh WWM610 BIM No: SpecEquip_GalvWlkWay_SayfaSystems_WWM1000GS_M3_G2
Prefabricated stair WWST545
Walkway clip WWFC510 Standing seam clamp WWFC515
2400STANDARD
WIDTHS 610mm25mm THICK32mm MESH
250
250
WALKWAY MESH WWM 610 PREFABRICATED STAIR WWST 545
STANDING SEAM CLAMP WWFC515WALKWAY CLIP WWFC 510
TO SUITANGLE OF ROOF
2400STANDARD
WIDTHS 610mm25mm THICK32mm MESH
250
250
WALKWAY MESH WWM 610 PREFABRICATED STAIR WWST 545
STANDING SEAM CLAMP WWFC515WALKWAY CLIP WWFC 510
TO SUITANGLE OF ROOF
2400STANDARD
WIDTHS 610mm25mm THICK32mm MESH
250
250
WALKWAY MESH WWM 610 PREFABRICATED STAIR WWST 545
STANDING SEAM CLAMP WWFC515WALKWAY CLIP WWFC 510
TO SUITANGLE OF ROOF
2400STANDARD
WIDTHS 610mm25mm THICK32mm MESH
250
250
WALKWAY MESH WWM 610 PREFABRICATED STAIR WWST 545
STANDING SEAM CLAMP WWFC515WALKWAY CLIP WWFC 510
TO SUITANGLE OF ROOF
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GALVANISED
072
COMPONENT PART DETAILS:Secret fix clamp WWFC520
Angled roof bracket WWRB200
Fixed handrail base plate D42-132 Joining strip WWJS505
SECRET FIX CLAMP WWF C520 BRACKET WWJB 505
WALKWAY JOINING STRIP600mm WIDE
FIXED HANDRAIL BASE PLATED42 132
TO SUITANGLE OF ROOF
SECRET FIX CLAMP WWF C520 BRACKET WWJB 505
WALKWAY JOINING STRIP600mm WIDE
FIXED HANDRAIL BASE PLATED42 132
TO SUITANGLE OF ROOF
SECRET FIX CLAMP WWF C520 BRACKET WWJB 505
WALKWAY JOINING STRIP600mm WIDE
FIXED HANDRAIL BASE PLATED42 132
TO SUITANGLE OF ROOF
SECRET FIX CLAMP WWF C520 BRACKET WWJB 505
WALKWAY JOINING STRIP600mm WIDE
FIXED HANDRAIL BASE PLATED42 132
TO SUITANGLE OF ROOF
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GALVANISED
FIXING DETAILS: Walkway fixed to steel deck roof
WALKWAYJOINER ORCLAMP
THIS FIXING DETAIL IS CORRECT FOR PEAK CENTRES UP TO 400mm
GALVANISED WALKWAYMESH SIZE 100mm x 38mm
WALKWAY25mm THICK
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GALVANISEDWALKWAY FIXEDTO STEEL DECK
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
SELF SEALINGROOFING SCREWTO SUIT ROOF DECK
WALKWAYFIXING CLIP
072
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GALVANISED
FIXING DETAILS: Walkway fixed to steel deck roof with steel support
WALKWAYJOINER ORCLAMP
THIS FIXING DETAIL IS CORRECT FOR PEAK CENTRES OVER 500mm
GALVANISEDWALKWAYMESH SIZE 100mm x 38mm
WALKWAY25mm THICK
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GALVANISEDWALKWAY FIXEDTO STEEL DECKWITH SUPPORT STEEL
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
SELF SEALINGROOFING SCREWTO SUIT ROOF DECKTO BE FITTED BOTHSIDES EVERY 1.5m
WALKWAYFIXING CLIPTO BE FITTEDBOTH SIDESEVERY 1.5m
SUPPORT STEEL40mm HIGH
072
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GALVANISED
FIXING DETAILS: Walkway fixed to steel deck roof with handrail
GAVVANISEDWALKWAYMESH SIZE 100mm x 38mm
Ø42mm TUBE AND FITTINGS
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GALVANISEDWALKWAY FIXED TOSTEEL DECKWITH HANDRAIL
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
SELF SEALING ROOFING SCREW TO SUIT ROOF DECKTO BE FITTED BOTH SIDES EVERY 1.5m
WALKWAYFIXING CLIPTO BE FITTED BOTH SIDESEVERY 1.5M
SUPPORT STEEL40mm HIGH
HANDRAIL BASE PLATEMAXIMUM SPACING 2.25m CENTRES
072
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GALVANISED
FIXING DETAILS: Raised walkway and stairs fixed to steel deck
3 MM L-BRACKET
STEEL SUPPORTTO SUIT ROOF ANGLE
WALKWAY FIXING CLIP
1000 mm GALVANISED WALKWAY
20° - 45°
20° - 45°
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GALVANISEDRAISED WALKWAY& STAIRS FIXED TOSTEEL DECK
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
ADJUSTABLE GALVANISEDSTEP FRAME WORK
GALVANISED WALKWAY250mm WIDE
SELF SEALINGROOFING SCREWSTO SUIT ROOF DECK
SELF SEALINGROOFING SCREWSTO SUIT ROOF DECK
5mm PROFILED ROOF CLAMPTO SUIT ROOF ANGLE
072
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - GALVANISED
FIXING DETAILS: Walkway fixed to standing seam roof
500
STANDARDWIDTH1000mm
LENGTHUP TO 600mm
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GALVANISEDWALKWAY FIXEDTO STANDING SEAMROOF
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
WALKWAYJOINER OR CLAMP
WALKWAYFIXING CLIP
ALUMINUM ROOFSEAM CLAMP
MINIMUM4 FIXINGCLAMPSPERWALKWAYSECTION
072
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Walkway fixed to standing seam roof with steel support
1000
STANDARDWIDTH1000mm
LENGTHUP TO6000mm
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GALVANISEDWALKWAY FIXEDTO STANDING SEAMROOF WITH SUPPORTSTEEL
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
WALKWAYJOINER OR CLAMP
WALKWAYFIXING CLIP
ALUMINUM ROOFSEAM CLAMP
MINIMUM4 FIXING CLAMPSPER WALKWAYSECTION
SUPPORT STEEL40mm HIGH
SUPPORTSTEELFOR SEAMSGREATER THAN500mm
PAYLOAD WALKWAY - GALVANISED
072
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Walkway fixed to standing seam roof with handrail
GALVANISEDWALKWAYMESH SIZE 100mm x 38mm
Ø42mm TUBE AND FITTINGS
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GALVANISEDWALKWAY FIXEDTO STANDING SEAMWITH HANDRAIL
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
SELF SEALING ROOFING SCREW TO SUIT ROOF DECKTO BE FITTED BOTH SIDES EVERY 1.5m
WALKWAYFIXING CLIPTO BE FITTED BOTH SIDESEVERY 1.5M
SUPPORT STEEL40mm HIGH
HANDRAIL BASE PLATEMAXIMUM SPACING 2.25m CENTRES
PAYLOAD WALKWAY - GALVANISED
072
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Raised walkway and stairs fixed to standing seam roof
3 MM L-BRACKET
STEEL SUPPORTTO SUIT ROOF ANGLE
WALKWAY FIXING CLIP
1000 mm GALVANISED WALKWAY
20° - 45°
20° - 45°
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GALVANISEDRAISED WALKWAY& STAIRS FIXED TOSTANDING SEAM
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
ADJUSTABLE GALVANISEDSTEP FRAME WORK
GALVANISED WALKWAY250mm WIDE
ALUMINUMROOF SEAM CLAMP
ALUMINUMROOF SEAM CLAMP
5mm PROFILED ROOF CLAMPTO SUIT ROOF ANGLE
ROOF SEAM
ROOF SEAM
PAYLOAD WALKWAY - GALVANISED
072
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Walkway fixed to secret fix roof
500
STANDARDWIDTH1000mm
LENGTHUP TO6000mm
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GALVANISEDWALKWAY FIXEDTO SECRET FIXROOF
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
WALKWAYJOINER OR CLAMP
WALKWAYFIXING CLIP
SECRET FIXCLAMP
MINIMUM4 FIXINGCLAMPSPERWALKWAYSECTION
PAYLOAD WALKWAY - GALVANISED
072
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Walkway fixed to secret fixed roof with steel support
1000
STANDARDWIDTH1000mm
LENGTHUP TO6000mm
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GALVANISEDWALKWAY FIXEDTO SECRET FIXROOF WITH SUPPORTSTEEL
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
WALKWAYJOINER OR CLAMP
WALKWAYFIXING CLIP
SECRET FIXCLAMP
MINIMUM4 FIXING CLAMPSPER WALKWAYSECTION
SUPPORT STEEL40mm HIGH
SUPPORT STEELFOR SEAMSGREATERTHAN 500mm
PAYLOAD WALKWAY - GALVANISED
072
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Walkway fixed to secret fixed roof with handrail
GALVANISED WALKWAYMESH SIZE 100mm x 38mm
Ø42mm TUBE AND FITTINGS
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GALVANISEDWALKWAY FIXEDTO SECRET FIXWITH HANDRAIL
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
SELF SEALING ROOFING SCREW TO SUIT ROOF DECKTO BE FITTED BOTH SIDES EVERY 1.5m
WALKWAYFIXING CLIPTO BE FITTED BOTH SIDESEVERY 1.5M
SUPPORT STEEL40mm HIGH
HANDRAIL BASE PLATEMAXIMUM SPACING 2.25m CENTRES
SECRET FIX CLAMP
PAYLOAD WALKWAY - GALVANISED
072
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Raised walkway and stairs fixed to secret fix roof
3 MM L-BRACKET
STEEL SUPPORTTO SUIT ROOF ANGLE
WALKWAY FIXING CLIP
1000 mm GALVANISED WALKWAY
20° - 45°
20° - 45°
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™GALVANISED RAISEDWALKWAY& STAIRS FIXED TOSECRET FIX
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
ADJUSTABLE GALVANISED STEP FRAME WORK
GALVANISED WALKWAY250mm WIDE
ALUMINUMSECRET FIX CLAMP
ALUMINUMSECRET FIX CLAMP
5mm PROFILED ROOF CLAMPTO SUIT ROOF ANGLE
SECRET FIXROOF SEAM
SECRET FIXROOF SEAM
PAYLOAD WALKWAY - GALVANISED
072
For any technical queries please call our adviceline on 0845 241 9102
DATE: 28/10/2014PRODUCT DATA SHEET REPORT NO: 073
PRODUCT CODE: WWM610AL
ALUMINIUM WALKWAY
073
For any technical queries please call our adviceline on 0845 241 9102 For any technical queries please call our adviceline on 0845 241 9102
PRODUCT DESCRIPTION:Aluminium walkway systems are designed to facilitate safe access and provide a designated access walkway on a roof. The walkway is 610mm or 810mm wide, supplied in 2.4m sections and is only 10mm thick. The mesh size is normally a diamond mesh design but can vary. The walkway is a natural aluminium finish. Aluminium will discolour over time although it is extremely resistant
PAYLOAD WALKWAY - ALUMINIUM
to rust. The walkway is designed to be laid on top of a completed roof system. It is a permanent means of access and usually left in position throughout the duration of the access requirements. Aluminium walkway systems are light weight but strong and blend in well on steel and standing seam roofs. The walkway provides excellent safety standards with minimal maintenance.
Up to 2.4m
810mm
610mm 10mm
10mm
073
For any technical queries please call our adviceline on 0845 241 9102 For any technical queries please call our adviceline on 0845 241 9102
The walkway is supplied with fixing clips and joiners to suit most types of roof profile. There are specialist clips for standing seam roofs and secret fix roofs which have been tested and approved for use. For steel composite panels the clip can be riveted to the deck with the Sayfa bulb type rivets. The walkway is
PAYLOAD WALKWAY - ALUMINIUM
not recommended for use on a PVC membrane roof and the Sayfa PVC walkway should be installed in these situations. For bitumen or hot melt rubber the walkway can be laid on top and the fixing clip fixed down with a suitable mastic or similar.
Standing seam
Composite steel Bitumen / Hot melt rubber
Secret fix
073
For any technical queries please call our adviceline on 0845 241 9102
Aluminium walkway is suitable for use on its own on a roof pitch of up to 10 degrees. Between 10 degrees and 20 degrees the walkway should be used with a handrail fixed to at least 1 side. The handrail is normally positioned on the lower edge of the walkway. Between 20 degrees to 45 degrees the walkway must be fitted with levelling plates, steps
Aluminium walkway is extremely hard wearing and has exceptional strength to weight ratio. The 10mm thick walkway can span a 500mm gap without additional supports. This makes it an extremely cost effective system for most prefabricated roof sections that have an up stand. If there are gaps wider than 500mm Than support bars should be fitted.. The mesh is non slip under normal working conditions. Care should be taken in extreme weather as some surfaces may become slippery. All fixings (except for mastic joints) are capable of supporting a shear load of 1.5Kn
and handrail on both sides. If handrail is to be fitted both sides it is recommended to use the 810mm wide panel to ensure the access width between the panels is no less than 600mm. It is not recommended to fit the walkway on any roofs over 45 degrees and a fixed access ladder should be considered in these situations.
force and a tension force of 0,5Kn. The walkway can support a weight of 150Kg spread over a 100mm area on the unsupported sections with a maximum deflection of 25mm. The ultimate SWL is 300kg on each complete walkway section. No more than 2 users are allowed on each walkway system at any time. The walkway is designed for occasional maintenance use only. Should high usage or fire access use be required we would recommend the use of GRP or galvanized walkway.
10o
10-20o
20-45o
Occasional maintenance use
Maximum users per unit
SWL 300Kg
1.5Kn0.5Kn
0,5m
PAYLOAD WALKWAY - ALUMINIUM
073
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - ALUMINIUM
GRP walkway is supplied with joiners or joining strip. Both types are suitable and conform to the required standards. It is possible at time of manufacture to paint the walkway different colours but large minimum quantities and additional charges will apply. The slip resistance of the aluminium flooring
The walkway can be integrated and used together with the Payload step overs and raised walkway if required. Involving our design team early will ensure that full consideration is given to the operator safety both during construction and for long term maintenance. It is recommended to use the walkway
is determined by a specific British standard test BS 4592. This slip test determines the friction of the walkway for wet areas and is conducted using a steady stream of water. Aluminium is not as slip resistant as GRP walkway and should be substituted for GRP in extreme conditions.
together with additional safety protection such as Payload handrail or The Aviator safety line system. Care must be taken with aluminum to prevent the contact of 2 dissimilar metals once installed.
1.10
1.00
0.90
0.80
0.70
0.60
0.50
0.40
0.30
0.20
1.04
On-track
CoF
(Co-
effic
ient
of f
rict
ion)
Metal grating Chequer plate
0.44
0.31
073
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - ALUMINIUM
MATERIAL SPECIFICATION:
Aluminium walkway clampsAluminium extrusion 0.50 - 0.75 Si, Max 0.35, Fe 0.40 - 0.70 MgTensile strength PSI 20,000 Yield strength PSI 11,000
Aluminium meshExpanded mesh 0.50 - 0.75 Si, Max 0.35, Fe 0.40 - 0.70 MgTensile strength PSI 23,000 Yield strength PSI 15,000
Aluminium
Aluminium
Aluminium
073
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - ALUMINIUM
OPERATING AND DESIGN STANDARDS:Eurocodes are designated by EN
British standards are designated by BS
• BS EN 516:2006 Class 1-C Fabricatedaccessories for roofing installations includingwalkways, treads and steps.
• BS4211:2005+A1:2008 Permanently fixedladders when used as steps or ladder treads.
• BS EN 12020-1 and 2 :2008 Aluminium andAluminium alloy extrusions for roof clamps
• BS EN 755:2008 series Extruded profiles• BS EN 754: 2008 series Tolerances on
dimensions extruded profiles• Plus standards from ACR M onwards
✔
BS ENISO
Standards
Typical connection loads (Maximum cantilever from substrate 75mm)
Uniform load 100mm2
Slip resistance
Tension
Maximum SWL
1.5Kn 0.5Kn
0.44CoF 300Kg
Note: For guidelines only to be checked by Chief Engineer.
073
• Work at height (amendment) Regulations2007 (Ref.8) WAHR
• Provision and use of work equipmentregulations 1998 PUWER 98 (Ref. 5)
• Management of health and safety at workregulations 1999 MHSWR (Ref.2)
• The Building Regulations 2010 part K.
The company operates to the following standards
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - ALUMINIUM
Maintenance to be in accordance with SIMS standards. (details available on request)
Maintenance to be carried out at time of yearly inspection.
Contact Sayfa Systems to arrange system maintenance.
TRAINING REQUIREMENTS:All personnel who use the Aviator system should have attended a NASLOT (National Access and Safety Line Operator Training) course. Courses are available from Sayfa Systems UK Ltd.
INSPECTION/MAINTENANCE/TRAINING
INSPECTION ROUTINE:All systems to be inspected at least every 12 months from date of installation.
In harsh environments all systems to be inspected at least every 3 months.
Inspections must be carried out by approved Aviator engineers.
Inspections must be approved to SIMS (Safety Inspection and Maintenance Service) standards.
All inspections to be carried out to EN795:2012 and BS 7883:2005 and WAHSA (inspection of eyebolts) requirements for safety line and anchor points.
All inspections to be carried out to EN364 requirements for personal protective equipment.
Contact Sayfa Systems to arrange inspections.
MAINTENANCE SCHEDULE:All maintenance to be carried out by approved Aviator engineers.
Maintenance to be in accordance with Sayfa Systems UK (manufacturer) guidelines and recommendations.
In harsh environments all systems to be inspected at least every 3 months.
12 Months
From date of installation
NASLOT
CERTIFIED
3Months
in harsh environments
d
Sa
yfa
SyStem
S
Ce
R t I f I C a
te
NASLOT
CERTIFIED
Certificate
PASS ✔
12 Months
From date of installation
3Months
in harsh environments
d
073
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - ALUMINIUM
073
COMPONENT PART DETAILS:Walkway mesh WWM610 BIM No: SpecEquip_AluWlkWay_SayfaSystems_WWM610AL_M3_G2
Prefabricated stair WWST545
Walkway clip WWFC510 Standing seam clamp WWFC515
2400STANDARD
WIDTHS 610mm25mm THICK32mm MESH
250
250
WALKWAY MESH WWM 610 PREFABRICATED STAIR WWST 545
STANDING SEAM CLAMP WWFC515WALKWAY CLIP WWFC 510
TO SUITANGLE OF ROOF
2400STANDARD
WIDTHS 610mm25mm THICK32mm MESH
250
250
WALKWAY MESH WWM 610 PREFABRICATED STAIR WWST 545
STANDING SEAM CLAMP WWFC515WALKWAY CLIP WWFC 510
TO SUITANGLE OF ROOF
2400STANDARD
WIDTHS 610mm25mm THICK32mm MESH
250
250
WALKWAY MESH WWM 610 PREFABRICATED STAIR WWST 545
STANDING SEAM CLAMP WWFC515WALKWAY CLIP WWFC 510
TO SUITANGLE OF ROOF
2400STANDARD
WIDTHS 610mm25mm THICK32mm MESH
250
250
WALKWAY MESH WWM 610 PREFABRICATED STAIR WWST 545
STANDING SEAM CLAMP WWFC515WALKWAY CLIP WWFC 510
TO SUITANGLE OF ROOF
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - ALUMINIUM
COMPONENT PART DETAILS:Secret fix clamp WWFC520
Angled roof bracket WWRB200
Fixed handrail base plate D42-132 Joining strip WWJS505
SECRET FIX CLAMP WWF C520 BRACKET WWJB 505
WALKWAY JOINING STRIP600mm WIDE
FIXED HANDRAIL BASE PLATED42 132
TO SUITANGLE OF ROOF
SECRET FIX CLAMP WWF C520 BRACKET WWJB 505
WALKWAY JOINING STRIP600mm WIDE
FIXED HANDRAIL BASE PLATED42 132
TO SUITANGLE OF ROOF
SECRET FIX CLAMP WWF C520 BRACKET WWJB 505
WALKWAY JOINING STRIP600mm WIDE
FIXED HANDRAIL BASE PLATED42 132
TO SUITANGLE OF ROOF
SECRET FIX CLAMP WWF C520 BRACKET WWJB 505
WALKWAY JOINING STRIP600mm WIDE
FIXED HANDRAIL BASE PLATED42 132
TO SUITANGLE OF ROOF
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - ALUMINIUM
FIXING DETAILS: Walkway fixed to steel deck roof
WALKWAYJOINER ORCLAMP
THIS FIXING DETAIL IS CORRECT FOR PEAK CENTRES UP TO 400mm
ALUMINIUM WALKWAYMESH SIZE 70mm x 40mm
WALKWAY10mm THICK
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ALUMINIUMWALKWAY FIXEDTO STEEL DECK
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
SELF SEALINGROOFING SCREWTO SUIT ROOF DECK
WALKWAYFIXING CLIP
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - ALUMINIUM
FIXING DETAILS: Walkway fixed to steel deck roof with steel support
WALKWAYJOINER ORCLAMP
THIS FIXING DETAIL IS CORRECT FOR PEAK CENTRES OVER 500mm
ALUMINIUMWALKWAYMESH SIZE 70-mm x 40mm
WALKWAY10mm THICK
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ALUMINIUMWALKWAY FIXEDTO STEEL DECKWITH SUPPORT STEEL
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
SELF SEALINGROOFING SCREWTO SUIT ROOF DECKTO BE FITTED BOTHSIDES EVERY 1.5m
WALKWAYFIXING CLIPTO BE FITTEDBOTH SIDESEVERY 1.5m
SUPPORT STEEL40mm HIGH
073
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - ALUMINIUM
FIXING DETAILS: Walkway fixed to steel deck roof with handrail
ALUMINIUMWALKWAYMESH SIZE 70mm x 40mm
Ø42mm TUBE AND FITTINGS
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ALUMINIUMWALKWAY FIXED TOSTEEL DECKWITH HANDRAIL
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
SELF SEALING ROOFING SCREW TO SUIT ROOF DECKTO BE FITTED BOTH SIDES EVERY 1.5m
WALKWAYFIXING CLIPTO BE FITTED BOTH SIDESEVERY 1.5M
SUPPORT STEEL40mm HIGH
HANDRAIL BASE PLATEMAXIMUM SPACING 2.25m CENTRES
073
For any technical queries please call our adviceline on 0845 241 9102
PAYLOAD WALKWAY - ALUMINIUM
FIXING DETAILS: Raised walkway and stairs fixed to steel deck
3 MM L-BRACKET
STEEL SUPPORTTO SUIT ROOF ANGLE
WALKWAY FIXING CLIP
610 mm ALUMINIUM WALKWAY
20° - 45°
20° - 45°
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ALUMINIUMRAISED WALKWAY& STAIRS FIXED TOSTEEL DECK
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
ADJUSTABLE ALUMINUM STEP FRAME WORK
ALUMINIUM WALKWAY250mm WIDE
SELF SEALINGROOFING SCREWSTO SUIT ROOF DECK
SELF SEALINGROOFING SCREWSTO SUIT ROOF DECK
5mm PROFILED ROOF CLAMPTO SUIT ROOF ANGLE
073
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Walkway fixed to standing seam roof
500
STANDARDWIDTH610mm
LENGTHUP TO 2400mm
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ALUMINIUMWALKWAY FIXEDTO STANDING SEAMROOF
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
WALKWAYJOINER OR CLAMP
WALKWAYFIXING CLIP
ALUMINUM ROOFSEAM CLAMP
MINIMUM4 FIXINGCLAMPSPERWALKWAYSECTION
PAYLOAD WALKWAY - ALUMINIUM
073
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Walkway fixed to standing seam roof with steel support
1000
LENGTHUP TO 2400mm
STANDARDWIDTH610mm
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ALUMINIUMWALKWAY FIXEDTO STANDING SEAMROOF WITH SUPPORTSTEEL
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
WALKWAYJOINER OR CLAMP
WALKWAYFIXING CLIP
ALUMINUM ROOFSEAM CLAMP
MINIMUM4 FIXING CLAMPSPER WALKWAYSECTION
SUPPORT STEEL40mm HIGH
SUPPORTSTEELFOR SEAMSGREATER THAN500mm
PAYLOAD WALKWAY - ALUMINIUM
073
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Walkway fixed to standing seam roof with handrail
ALUMINIUMWALKWAYMESH SIZE 70mm x 40mm
Ø42mm TUBE AND FITTINGS
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ALUMINIUMWALKWAY FIXEDTO STANDING SEAMWITH HANDRAIL
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
SELF SEALING ROOFING SCREW TO SUIT ROOF DECKTO BE FITTED BOTH SIDES EVERY 1.5m
WALKWAYFIXING CLIPTO BE FITTED BOTH SIDESEVERY 1.5M
SUPPORT STEEL40mm HIGH
HANDRAIL BASE PLATEMAXIMUM SPACING 2.25m CENTRES
PAYLOAD WALKWAY - ALUMINIUM
073
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Raised walkway and stairs fixed to standing seam roof
3 MM L-BRACKET
STEEL SUPPORTTO SUIT ROOF ANGLE
WALKWAY FIXING CLIP
1000 mm ALUMINIUM WALKWAY
20° - 45°
20° - 45°
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ALUMINIUMRAISED WALKWAY& STAIRS FIXED TOSTANDING SEAM
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
ADJUSTABLE ALUMINIUM STEP FRAME WORK
ALUMINIUM WALKWAY250mm WIDE
ALUMINUMROOF SEAM CLAMP
ALUMINUMROOF SEAM CLAMP
5mm PROFILED ROOF CLAMPTO SUIT ROOF ANGLE
ROOF SEAM
ROOF SEAM
PAYLOAD WALKWAY - ALUMINIUM
073
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Walkway fixed to secret fix roof
500
STANDARDWIDTH610mm
LENGTHUP TO 2400mm
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ALUMINIUMWALKWAY FIXEDTO SECRET FIXROOF
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
WALKWAYJOINER OR CLAMP
WALKWAYFIXING CLIP
SECRET FIXCLAMP
MINIMUM4 FIXINGCLAMPSPERWALKWAYSECTION
PAYLOAD WALKWAY - ALUMINIUM
073
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Walkway fixed to secret fixed roof with steel support
1000
STANDARDWIDTH610mm
LENGTHUP TO 2400mm
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ALUMINUMWALKWAY FIXEDTO SECRET FIXROOF WITH SUPPORTSTEEL
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
WALKWAYJOINER OR CLAMP
WALKWAYFIXING CLIP
SECRET FIXCLAMP
MINIMUM4 FIXING CLAMPSPER WALKWAYSECTION
SUPPORT STEEL40mm HIGH
SUPPORT STEELFOR SEAMSGREATERTHAN 500mm
PAYLOAD WALKWAY - ALUMINIUM
073
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Walkway fixed to secret fixed roof with handrail
ALUMINIUM WALKWAYMESH SIZE 70mm x 40mm
Ø42mm TUBE AND FITTINGS
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ALUMINIUMWALKWAY FIXEDTO SECRET FIXWITH HANDRAIL
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
SELF SEALING ROOFING SCREW TO SUIT ROOF DECKTO BE FITTED BOTH SIDES EVERY 1.5m
WALKWAYFIXING CLIPTO BE FITTED BOTH SIDESEVERY 1.5M
SUPPORT STEEL40mm HIGH
HANDRAIL BASE PLATEMAXIMUM SPACING 2.25m CENTRES
SECRET FIX CLAMP
PAYLOAD WALKWAY - ALUMINIUM
073
For any technical queries please call our adviceline on 0845 241 9102
FIXING DETAILS: Raised walkway and stairs fixed to secret fix roof
3 MM L-BRACKET
STEEL SUPPORTTO SUIT ROOF ANGLE
WALKWAY FIXING CLIP
1000 mm ALUMINIUM WALKWAY
20° - 45°
20° - 45°
Client:
Contract:
Project Title:
Line to be located as indicated on theroof plan.
Line primarily used to gain access toexposed roof edges.
Incorporates Aviator™ units and allSayfa Systemscomponents required.
Fixing details for Aviator™ units asindicated within layout.
System to be used in conjunction with2m restraining lanyard unless statedotherwise.
Enables two users simultaneously atany one time.
System Details
SAYFA SYSTEMS
FIXING DETAIL
PAYLOAD™ALUMINIUM RAISEDWALKWAY& STAIRS FIXED TOSECRET FIX
Revision:
Drawn By: MW
Scale:
Date:
Checked By:
Job No:
DWG No:
Jubilee House
ShepshedLeicestershireLE12 9NHT: 0845 241 9102F:0845 130 4520www.sayfasystems.com
Unit 3, Gelders Hall Road
Status:
S:\Design\Mark's Temp CAD\SAYFA CAD Templates\SAYFA CAD TEMPLATE FILES\Sayfa_Logo_New.jpg
UNDER THE CDM REGULATIONS 200, IF ANY ALTERATIONS ARE MADE TO THIS DRAWING THEN THE PERSON UNDERTAKING THESE CHANGES ASSUME THE ROLE OF THE DESIGNER, THEREFORE TAKING FULL CDM RESPONSIBILITY.
A = Access point
Drawing Symbols
THIS DRAWING IS PROTECTED BY COPYRIGHT AND THE INFORMATION HEREIN IS CONFIDENTIAL. THE DRAWING MAY NOT BE COPIED AND THE INFORMATION HEREIN MAY NOT BE USED OR DISCLOSED EXCEPT WITH THE WRITTEN PERMISSION OF SAYFA SYSTEMS ©
DRAWING REVISIONSREV DATE COMMENT
THIS DRAWING WAS CREATED INCONJUNCTION WITH ____________
DRAWING NO. ______________
TYPICAL FIXING DETAILS
22/12/2014
As Dimensioned
For DesignN/A
N/A
001
DJ
ADJUSTABLE ALUMINIUM STEP FRAME WORK
ALUMINIUM WALKWAY250mm WIDE
ALUMINUMSECRET FIX CLAMP
ALUMINUMSECRET FIX CLAMP
5mm PROFILED ROOF CLAMPTO SUIT ROOF ANGLE
SECRET FIXROOF SEAM
SECRET FIXROOF SEAM
PAYLOAD WALKWAY - ALUMINIUM
073